DALUME L
I G H T I N G
DRL11_RM - Sheet Rock Ceiling Recessed Mount FIG. A
Framing
Opening
12" x 12"
R
LIGHTING GROUP
LOS ANGELES, CA
SAVE THESE INSTRUCTIONS
INSTALL AND USE THIS LUMINAIRE FOLLOWING THE NATIONAL ELECTRICAL
CODE, YOUR LOCAL ELECTRICAL CODE AND REGULATIONS.
1 PREPARATION:
4x Wood
Screw
Recessed
Frame
EEMA
1). Read and understand instructions completely before installing this luminaire. If you are unfamiliar
with electrical wiring have a qualified licensed electrician installs this luminaire.
2). Before proceeding the installation, be sure that the ceiling construction follows the proper requirements.
3). Custom Framing is required, Installer may build a wood joist framing as specified in FIG. A.
Framing clearance and Sheet-rock (ceiling) Opening must be 12" x 12" x 6" Height.
CAUTION!
FIG. B
(1x) 3/4" K.O.
Recessed
Luminaire
FIG. C
Wood Screws
@ 1.75" Height
FIG. D
FINAL INSTALLATION
1-3/4"
CEILING MOUNTED
FIG. E
WIRING DIAGRAM
POWER
SUPPLY
Ground
Wire
Ground
Wire
Line (-)
Wire
NON-IC LUMINAIRES: Ceiling insulation must be kept a minimum of 3" away from the sides of the
framing. No insulation allowed on the top. Install housing at a minimum of 1/2" away from
combustible material such as sub-flooring or roofing.
2 INSTALLING LUMINAIRE RECESSED FRAME:
NOTE: Ceiling (sheet-rock) must be installed prior to Luminaire Recessed Frame installation.
1). Place Recessed Frame into Ceiling Opening. Make sure the frame flanges are flush (level) with ceiling
surface, then install Frame using Wood Screws (by others) as shown in illustration (see FIG. A).
2). In order to be able to install the Recessed Luminiare into the Frame, pass Electrical Supply through
Frame and connect to Luminaire Electrical Box to make electrical connection (see FIG. E).
3 ELECTRICAL CONNECTIONS:
1). WARNING- Before starting the wire connections, disconnect the power by turning off
the circuit breaker or removing the fuse at the fuse panel. Turning the power off using the light switch
is not sufficient to prevent electrical shock.
2). This luminaire must be connected with supply wire rated at 90o C. Most dwellings built before 1985
have supply wire rated at 60o C; consult a qualified electrician before installing.
3). Connect the power source to the luminaire junction box. Connect the line (-) wire to the black wire of
the power source, the neutral (+) wire to the white wire of the power source and connect the ground
wire to the green ground wire of the power source using twist type wire connectors (by others) suitable
for the size, type and number of wires; see wiring diagram (see FIG. E).
4). After completing the wiring (be sure the wires are placed within the electrical box), replace J-Box cover.
4 INSTALLING RECESSED LUMINAIRE:
1). Tilt Recessed Luminaire and insert it all away into the Frame in diagonal angle. Lens facing down
(see FIG. B).
2). Let the Recessed Luminaire come down and rest on the Frame Flanges as shown in illustration
(see FIG. C & D).
WARNING-DO NOT REPLACE ANY ELECTRICAL COMPONENT for this Luminaire without
consulting a qualified Electrician or Luminaire Manufacturer.
* Consult factory for Remote LED driver ordering and installation.
Black Wire
White Wire
Neutral (+)
Wire
DALUME
R
DALUME L
EEMA
I G H T I N G
DRL11_RM - TEE BAR Ceiling Recessed Mount FIG. A
12" x 12"
T-Bar spacing
Luminaire
Opening
R
LIGHTING GROUP
LOS ANGELES, CA
SAVE THESE INSTRUCTIONS
INSTALL AND USE THIS LUMINAIRE FOLLOWING THE NATIONAL ELECTRICAL
CODE, YOUR LOCAL ELECTRICAL CODE AND REGULATIONS.
1 PREPARATION:
FIG. B
1). Read and understand instructions completely before installing this luminaire. If you are unfamiliar
with electrical wiring have a qualified licensed electrician installs this luminaire.
2). Before proceeding the installation, be sure that the ceiling construction follows the proper requirements.
3). 12in x 12in T-Bar Framing is required, as specified in FIG. A.
Framing clearance (ceiling) Opening must be 12" x 12" x 10" Height.
CAUTION!
NON-IC LUMINAIRES: Ceiling insulation must be kept a minimum of 3" away from the sides of the
framing. No insulation allowed on the top. Install housing at a minimum of 1/2" away from
combustible material such as sub-flooring or roofing.
2 INSTALLING POWER SUPPLY:
Recessed
Luminaire
FIG. C
NOTE: Ceiling Suspension Cables must be installed prior to Recessed Luminaire installation.
1). In order to be able to install the Recessed Luminiare into the Framing, pass Electrical Supply through
Ceiling Opening and connect to Luminaire Electrical Box to make electrical connection (see FIG. E).
3 ELECTRICAL CONNECTIONS:
1). WARNING- Before starting the wire connections, disconnect the power by turning off
the circuit breaker or removing the fuse at the fuse panel. Turning the power off using the light switch
is not sufficient to prevent electrical shock.
2). This luminaire must be connected with supply wire rated at 90o C. Most dwellings built before 1985
have supply wire rated at 60o C; consult a qualified electrician before installing.
3). Connect the power source to the luminaire junction box. Connect the line (-) wire to the black wire of
the power source, the neutral (+) wire to the white wire of the power source and connect the ground
wire to the green ground wire of the power source using twist type wire connectors (by others) suitable
for the size, type and number of wires; see wiring diagram (see FIG. E).
4). After completing the wiring (be sure the wires are placed within the electrical box), replace J-Box cover.
FIG. D
FINAL INSTALLATION
(1x) 3/4" K.O.
Suspension
Cables
FIG. E
WIRING DIAGRAM
POWER
SUPPLY
Ground
Wire
1). Tilt Recessed Luminaire and insert it all away into the Frame in diagonal angle. Lens facing down
(see FIG. B).
2). Let the Recessed Luminaire come down and rest on the Frame Flanges as shown in illustration
(see FIG. C & D).
NOTE: When Installing with Suspension Cables, access above ceiling is required (see FIG. D).
T-BAR CEILING MOUNTED
Ground
Wire
4 INSTALLING RECESSED LUMINAIRE:
Line (-)
Wire
WARNING-DO NOT REPLACE ANY ELECTRICAL COMPONENT for this Luminaire without
consulting a qualified Electrician or Luminaire Manufacturer.
* Consult factory for Remote LED driver ordering and installation.
Black Wire
White Wire
Neutral (+)
Wire
DALUME
R
DALUME L
I G H T I N G
DRL11_SM - Ceiling / Wall Surface Mount -
LIGHTING GROUP
LOS ANGELES, CA
SAVE THESE INSTRUCTIONS
1 PREPARATION:
4x Mounting
Screw
Surface
Frame
R
INSTALL AND USE THIS LUMINAIRE FOLLOWING THE NATIONAL ELECTRICAL
CODE, YOUR LOCAL ELECTRICAL CODE AND REGULATIONS.
4x Screw
Anchor
FIG. A
1). Read and understand instructions completely before installing this luminaire. If you are
unfamiliar with electrical wiring have a qualified licensed electrician installs this luminaire.
2). Before proceeding the installation, be sure that the ceiling construction follows the proper
requirements .
2 INSTALLING LUMINAIRE SURFACE FRAME:
NOTE: Ceiling / Wall (sheet-rock) must be installed prior to Luminaire Surface Frame installation.
1). Choose desire location, place Surface Frame on mounting surface and trace the holes.
4 mounting holes minimum required (see FIG. A).
2). Insert Screw Anchors (by others) into sheet-rock openings. Make sure the Screw Anchors are
flush with mounting surface and install the Surface Frame using Mounting Screws (by others)
as shown (see FIG. A).
3). In order to be able to install the Surface Luminiare into the Frame, pass Electrical Supply
through Frame and connect to Luminaire Electrical Box to make electrical connection
(see FIG. E).
Surface
Luminaire
FIG. B
4x Machine
Screw
FIG. C
FIG. D
FINAL INSTALLATION
WALL MOUNTED
FIG. E
WIRING DIAGRAM
Ground
Wire
Ground
Wire
3 MAKE ELECTRICAL CONNECTIONS:
1). WARNING- Before starting the wire connections, disconnect the power by turning
off the circuit breaker or removing the fuse at the fuse panel. Turning the power off using the
light switch is not sufficient to prevent electrical shock.
o
2). This luminaire must be connected with supply wire rated at 90 C. Most dwellings built before
o
1985 have supply wire rated at 60 C; consult a qualified electrician before installing.
3). Connect the power supply to the Luminaire Junction Box. Connect the line (-) wire to the black
wire of the power supply, the neutral (+) wire to the white wire of the power supply and
connect the ground wire to the green ground wire of the power supply using twist type wire
connectors (by others) suitable for the size, type and number of wires; see wiring diagram
(see FIG. E).
4). After completing the wiring (be sure the wires are placed within the electrical box),
replace J-Box cover.
4 INSTALLING SURFACE LUMINAIRE:
CEILING MOUNTED
POWER
SUPPLY
EEMA
Line (-)
Wire
1). Place Surface Luminaire into the Frame and install using the four Machine screws provided
(see FIG. B & C).
WARNING-DO NOT REPLACE ANY ELECTRICAL COMPONENT for this Luminaire without
consulting a qualified Electrician or Luminaire Manufacturer.
* Consult factory for Remote LED driver ordering and installation.
Black Wire
White Wire
Neutral (+)
Wire
DALUME
R