2.02
GENERATOR SET EXERCISE (TEST) WITH LOAD MODE. THE CONTROL
SYSTEM SHALL BE CONFIGURABLE TO TEST THE GENERATOR SET
UNDER LOAD. IN THIS MODE, THE TRANSFER SWITCH SHALL CONTROL
THE GENERATOR SET IN THE FOLLOWING SEQUENCE:
TRANSFER SWITCH SHALL INITIATE THE EXERCISE SEQUENCE AT A
TIME INDICATED IN THE EXERCISE TIMER PROGRAM, OR WHEN
MANUALLY INITIATED BY THE OPERATOR.
WHEN THE CONTROL SYSTEMS SENSE THE GENERATOR SET AT RATED
VOLTAGE AND FREQUENCY, IT SHALL OPERATE TO CONNECT THE LOADS
TO THE GENERATOR SET BY OPENING THE NORMAL SOURCE
CONTACTS, AND CLOSING THE ALTERNATE SOURCE CONTACTS A
PREDETERMINED TIME PERIOD LATER. THE TIMING SEQUENCE FOR
THE CONTACT OPERATION SHALL BE PROGRAMMABLE IN THE
CONTROLLER.
THE GENERATOR SET SHALL OPERATE CONNECTED TO THE LOAD FOR
THE DURATION OF THE EXERCISE PERIOD. IF THE GENERATOR SET
FAILS DURING THIS PERIOD, THE TRANSFER SWITCH SHALL
AUTOMATICALLY RECONNECT THE GENERATOR SET TO THE NORMAL
ON COMPLETION OF THE EXERCISE PERIOD, THE TRANSFER SWITCH
SHALL OPERATE TO CONNECT THE LOADS TO THE NORMAL SOURCE BY
OPENING THE ALTERNATE SOURCE CONTACTS, AND CLOSING THE
NORMAL SOURCE CONTACTS A PREDETERMINED TIME PERIOD LATER.
THE TIMING SEQUENCE FOR THE CONTACT OPERATION SHALL BE
PROGRAMMABLE IN THE CONTROLLER.
THE TRANSFER SWITCH SHALL OPERATE THE GENERATOR SET UNLOADED
FOR A COOL-DOWN PERIOD, AND THEN REMOVE THE START SIGNAL
FROM THE GENERATOR SET. IF THE NORMAL POWER FAILS AT ANY
TIME WHEN THE GENERATOR SET IS RUNNING, THE TRANSFER SWITCH
SHALL IMMEDIATELY CONNECT THE SYSTEM LOADS TO THE GENERATOR SET.
2.03
GENERATOR SET EXERCISE (TEST) WITHOUT LOAD MODE. THE
CONTROL SYSTEM SHALL BE CONFIGURABLE TO TEST THE GENERATOR
SET WITHOUT TRANSFER SWITCH LOAD CONNECTED. IN THIS MODE,
THE TRANSFER SWITCH SHALL CONTROL THE GENERATOR SET IN THE
FOLLOWING SEQUENCE:
TRANSFER SWITCH SHALL INITIATE THE EXERCISE SEQUENCE AT A
TIME INDICATED IN THE EXERCISE TIMER PROGRAM, OR WHEN
MANUALLY INITIATED BY THE OPERATOR.
WHEN THE CONTROL SYSTEMS SENSE THE GENERATOR SET AT RATED
VOLTAGE AND FREQUENCY, IT SHALL OPERATE THE GENERATOR SET
UNLOADED FOR THE DURATION OF THE EXERCISE PERIOD.
AT THE COMPLETION OF THE EXERCISE PERIOD, THE TRANSFER SWITCH
SHALL REMOVE THE START SIGNAL FROM THE GENERATOR SET. IF
THE NORMAL POWER FAILS AT ANY TIME WHEN THE GENERATOR SET
IS RUNNING, THE TRANSFER SWITCH SHALL IMMEDIATELY CONNECT THE
SYSTEM LOADS TO THE GENERATOR SET.
3.0 CONSTRUCTION AND PERFORMANCE
3.01 THE TRANSFER SWITCH MANUFACTURER SHALL SUBMIT TEST DATA FOR EACH
SIZE SWITCH, SHOWING IT CAN WITHSTAND FAULT CURRENTS OF THE MAGNITUDE
AND THE DURATION NECESSARY TO MAINTAIN SYSTEM INTEGRITY. MINIMUM
UL LISTED WITHSTAND AND CLOSING RATINGS SHALL BE AS FOLLOWS:
SIZE (AMPS)
100-400
401-600
601-1200
ANY MOLDED BREAKER
(RMS SYMMETRICAL)
35,000
50,000
50,000
SIZE (AMPS)
100-400
401-600
601-1200
SPECIFIC COORDINATED
MOLDED CASE BREAKER
50,000
65,000
85,000
SIZE (AMPS)
100-4000
CURRENT
LIMITING FUSE
200,000
LIGHTOLIER
8037CLW
S7142BU
BETA-CALCO
63 2441 3A
XX 1 DB
G
3.08 THE TRANSFER SWITCH SHALL BE PROVIDED WITH 4 HOURS OF FACTORY
TRAINED INSTRUCTIONS COORDINATED WITH FACULTY. INSTRUCTION MAY BE
VIDEOTAPED AT OWNERS DISCRETION.
H
BETA-CALCO
63 9802
XX1
COOPER
LIGHTING
LA8055ML
NOTES
1. A 24 VDC SHUNT TRIP OPERATOR MUST BE PROVIDED ON THE GENERATOR
FEEDER BREAKER TO OPERATE SHOULD THE TWO SOURCES BE PARALLELED
FOR LONGER THAN SPECIFIED PARAMETERS
8021CCL
S6132BU
LIGHTOLIER
I
EG1-13-FO81W-D
J
2. 24 VDC MUST BE SUPPLIED FROM THE ENGINE BATTERIES FOR USE WITH THE
SHUNT TRIP CIRCUIT AND AS A BACKUP FOR ALARM FUNCTIONS.
QVS2GSD
GC1FT120VBE
K
3. TRANSFER SWITCH SHALL BE IN CONFORMANCE WITH THE APPLICABLE PORTIONS OF:
UL 1008
NFPA 70
NFPA 110
IEEE 241
IEEE 446
NEMA ICS
UL 50/508
ICS 6
NEMA 250
L
JESCO
M
INSIGHT
LIGHTING
N
----
FUSED DISCONNECT SWITCH, SIZE PER NEC.
HUBBELL
HBL1221
AC SWITCH SPECIFICATION GRADE, TOGGLE TYPE, SINGLE POLE, 20A,
120V. PROVIDE WITH WALL PLATE. COORDINATE FINISH WITH
ARCHITECT. MOUNT 44" A.F.F. U.O.N.
3
HUBBELL
HBL1223
AC SWITCH SPECIFICATION GRADE, TOGGLE TYPE, THREE-WAY, 20A,
120V. PROVIDE WITH WALL PLATE. COORDINATE FINISH WITH
ARCHITECT. MOUNT 44" A.F.F. U.O.N.
44W LED
ARRAY
2'x4' SHIELDED RECESSED LED FIXTURE. RECTANGULAR PERF INLAY
SHEILD WITH 4000K LED LAMP. 120V.
3D
HUBBELL
AS63
ARCHITECTURAL GRADE SLIDER TYPE THREE-WAY DIMMER SWITCH,
PRESET, 600w, 120V AC. PROVIDE WITH WALL PLATE. COORDINATE
FINISH WITH ARCHITECT. MOUNT 44" A.F.F. U.O.N.
HUBBELL
HBL5262
DUPLEX SPECIFICATION GRADE RECEPTACLE, 20 AMPS, 3 WIRE
GROUNDING. PROVIDE WITH WALL PLATE. COORDINATE FINISH WITH
ARCHITECT. MOUNT 18" A.F.F. U.O.N.
HUBBELL
----
SAME AS ABOVE EXCEPT MOUNT 44" A.F.F.
HUBBELL
----
QUAD SPECIFICATION GRADE RECEPTACLE, 20 AMPS, 3 WIRE
GROUNDING. PROVIDE WITH WALL PLATE. COORDINATE FINISH WITH
ARCHITECT. MOUNT 18" A.F.F. U.O.N.
50W LED
ARRAY
6"x48" RECESSED CEILING LED FIXTURE. LED DRIVER 4000K, 120V.
"CALCULITE" CFL OPEN DOWNLIGHT WITH 8" APERATURE. 26W TRIPLE TUBE
CFL, 120V.
(1) 26W C.F.
"TRILOGY CRADLE" TRIPLE ARM LIGHTING FIXTURE. HIGH FREQUENCY
ELECTRONIC BALLASTS, 120V. FINISH SELECTION BY ARCHITECT.
(3) 32W C.F.
"TRILOGY" PENDANT MOUNT LIGHTING FIXTURE. HIGH FREQUENCY
ELECTRONIC BALLASTS, 120V. FINISH SELECTION BY ARCHITECT.
(2) 32W C.F.
GFI
HUBBELL
GF5362
14W LED
ARRAY
GFI
HUBBELL
----
SAME AS ABOVE EXCEPT MOUNT 44" A.F.F.
(1) 32W C.F.
GFI
WP
HUBBELL
----
SAME AS ABOVE EXCEPT PROVIDE WITH WEATHER PROOF COVER
PLATE PER EXTERIOR RECEPTACLES. MOUNT 18" A.F.F. U.O.N.
HUBBELL
HBL45123C
----
----
TV JACK IN SINGLE GANG BOX WITH
WITH PULL STRING MOUNT 40" A.F.F
----
----
TELEPHONE OUTLET SINGLE GANG BOX WITH 3/4" CONDUIT TO ABOVE
CEILING WITH PULL STRINGS. COORDINATE WORK WITH FIELD
CONDITIONS AND OTHER TRADES.
----
----
DATA/TELEPHONE OUTLET. DOUBLE GANG BOX WITH 3/4" CONDUIT TO
ABOVE CEILING WITH PULL STRINGS. COORDINATE WORK WITH FIELD
CONDITIONS AND OTHER TRADES.
CR
SCHLAGE
AD300CY50PR
SPA626PDC123
4. SEE SPECIFICATION SECTION 263600 - TRANSFER SWITCHES FOR ADDITIONAL REQUIREMENTS
CR2
HID
PROXPRO
5355
GENERATOR SPECIFICATIONS
SP
----
----
TYPE:
208Y/120V, 3PH, 4W, 200 KW, DIESEL FUELED.
MANUFACTURER: GENERAC
MODEL:
SD-200
GENERATOR SET SPECIFICATIONS:
VOLTAGE REGULATION, NO LOAD TO FULL LOAD:
RANDOM VOLTAGE VARIATION:
FREQUENCY REGULATION:
RANDOM FREQUENCY REGULATION:
±1.0%
±1.0%
ISOCHRONOUS (ELECTRONIC GOVERNOR STANDARD)
±.0.25%
ENGINE SPECIFICATIONS:
DESIGN:
BORE:
STROKE:
DISPLACEMENT:
STARTING VOLTAGE:
FUEL SYSTEMS:
AIR CLEANER TYPE:
LUBE OIL FILTER TYPE(S):
BMEP:
ASPIRATION:
6 CYCL., WATER-COOLED
4.61"
5.31"
8.7L
24 VOLT, NEGATIVE GROUND
DIESEL
DRY ELEMENT
SPIN-ON, FULL FLOW
265 PSI
TURBO CHARGED/AFTERCOOLED
ALTERNATOR SPECIFICATIONS:
DESIGN:
STATOR:
ROTOR
INSULATION SYSTEM:
TEMPERATURE RISE:
EXCITER TYPE:
PHASE ROTATION:
ALTERNATOR COOLING:
AC WAVEFORM TOTAL HARMONIC DISTORTION:
TELEPHONE INFLUENCE FACTOR (TIF)
BRUSH LESS, 4 POLE, DRIP PROOF REVOLVING FIELD
2/3 PITCH
DIRECT COUPLED BY FLEXIBLE DISC
CLASS H PER NEMA MG1-1.65
125°C STANDBY
PERMANENT MAGNET
A (U), B (V), C (W)
DIRECT DRIVE CENTRIFUGAL BLOWER
<5% TOTAL NO LOAD TO FULL LINEAR LOAD
<50 PER NEMA MG1-22.43.
(2) 28W T5
"ENERGOS" LINEAR PENDANT FIXTURE. (DIRECT/INDIRECT) 3 BULB T5.
PARABOLIC LOUVER WITH DUAL SWITCHING. 120V.
2'x2' RECESSED DIRECT/INDIRECT FLUORESCENT 1 LAMP FIXTURE. SOLID
GLASS SHIELD. ALTER SOFT LIGHTS, 120V.
S6014840
SAME AS FIXTURE ABOVE EXCEPT 48" IN LENGTH.
14W LED ARRAY
"MEDLEY C" LINEAR LED ACCENT FIXTURE. 24" LENGTH, SURFACE
MOUNT, ADJUSTABLE DOWNWARD LIGHT THROW. 5000K, 120V.
26W LED ARRAY
68070184
WZNC
P
EUROFASE
19240-015
CM
(1) 50W TT5
7W LED ARRAY
RESTORATION
HARDWARE
R
"CALCULITE" CFL OPEN DOWNLIGHT WITH 6" APERATURE. 32W TRIPLE TUBE
CFL, 120V.
SLIM COVE LED LIGHTING FIXTURE. MOUNTED UNDER BAR FOR SOFT
DISPLAY ACCENT LIGHTING. 4000K. 24" IN LENGTH.
O
Q
"HALO" SERIES STASIS LED SMALL. 4000K 8° SPOT BEAM. ADJUSTABLE
ON MOUNTED ARCHITECTURAL TRACK. FINISH BY SELECTION
ARCHITECT.
TV
W
(1) 26W C.F.
w/ EDISON BASE
VINTAGE BARN PENDANT WEATHERED ZINK FIXTURE. 18" ZINK SHADE, 75W.
SURFACE MOUNTED, FULLY ADJUSTABLE, LED SPOTLIGHT. METAL
CONSTRUCTION, FINISH BY ARCHITECT.
(1) 1W LED
"TRILOGY" CRADLE SEMI-RECESSED FIXTURE. 120V. TRIM FINISH BY
ARCHITECT.
(2) 32W C.F.
BETA-CALCO
63 2130
PL-T
LIGHTOLIER
ST74WA43
A40UUADB
SEALATRON LED ENCLOSED INDUSTRIAL WET LOCATION SURFACE MOUNTED
LUMINAIRE PRODUCING 4300 LUMENS AND 4000 DEGREE KELVIN COLOR
TEMPERATURE, 120V.
LIGHTOLIER
ST74WA43
A40UUADB
SEALATRON LED ENCLOSED INDUSTRIAL WET LOCATION SURFACE MOUNTED
LUMINAIRE PRODUCING 4300 LUMENS AND 4000 DEGREE KELVIN COLOR
TEMPERATURE, 120V.
WAC LIGHTING
LED-RL-30
LOW PROFILE LED ROPE LIGHT. 1/2" ROPE WITH LEDS SPACED EVERY 1".
DIMMABLE WATERPROOF AND UV RESISTANT. DIRECTLY CONNECTED TO
120V POWER SUPPLY TO PROVIDE SOFT GLOW BEHIND SIGNAGE, TO BE
CONNECTED TO SITE LIGHTING CONTACT TO OPERATE FROM DUSK TO
DAWN.
T
1.
AIPHONE
IS-IPMV
IP SECURITY DESK CONTROLLER. DESK MOUNTED STATION WITH 3.5" LCD
MONITOR. EQUIPPED WITH AUDIO OUTPUT AND DOOR RELEASE BUTTON.
PROVIDE AND INSTALL CAT 5E CABLING WITH PULLSTRING IN CONDUIT TO
ABOVE CEILING.
AIPHONE
AX-DV-P
IP INTERCOM VIDEO DOOR STATION. EQUIPPED WITH COLOR VIDEO
CAMERA, AUDIO INTERCOM, AND EMBEDDED CARD READER. PROVIDE
AND INSTALL CAT 5E CABLING.
---
---
G
GENERAC
SD-200
EMERGENCY INDUSTRIAL DIESEL GENERATOR. 250 KVA, 200 KW, 60 HZ.
PROVIDE WITH LEVEL 2 SOUND ENCLOSURE.
5000
MITEL
SERIES 5000
5000 IP
52002686
COMMUNICATION PLATFORM - SYSTEM HARDWARE BASE KIT HX NO CF
MT 5000 HX. PROVIDE WITH THE FOLLOWING:
VI
REFER TO MEP-2 FOR OUTDOOR LIGHTING SCHEDULE & DETAILS.
ML-1
PP-3
(MECH. RM.)
SPECIFICATIONS:
SEE SPECIFICATION SECTION 26 32 13 FOR ADDITIONAL REQUIREMENTS
MITEL
DESKTOP
DEVICE
50006476
COMMUNICATION PLATFORM - SOFTWARE LICENSES MT5000 LIC FILE BASED
MUSIC SOURCE
5330e IP PHONE. MULTI-FUNCTION PROGRAMMABLE SELF-LABELING KEYS,
LARGE PRAGHIC DISPLAY, WIDEBAND AUDIO SUPPORT, HANDS FREE
SPEAKER PHONE OPERATION.
25CX30L3G
726008
BK1000
BK1001
CA 1013
MS 1050
MP-1
(PENTHOUSE)
LP-2
(MECH. RM.)
150A
MCB
NETWORK
SWITCHES
250A
MCB
J9087A#ABA
MPC4PL5ST-05
CONNECT IP PHONE VIA CAT. 5E OR CAT. 6 CABLE BACK TO COMMUNICATION PLATFORM LOCATED IN IT ROOM.
CONTRACTOR TO PROVIDE ALL NECESSARY HARDWARE AND APPURTENANCES FOR A COMPLETE AND OPERABLE
SYSTEM. COORDINATE WITH OWNER FOR FINAL PHONE LOCATIONS.
NEW 300 KVA
13.2KV:208Y/120V
PAD-MOUNT TRANSFORMER
10'-0"
800 AMP METER
WITH CT CABINET
M
#1/0 GND
KP-1
(STORAGE)
IG-1
(IT RM.)
PP-4
(ELEC. RM.)
EN
0
PR
7 3 0 8 4
OF E
S S I ON
AL
1
200A
MCB
150A
MCB
200A
MCB
200A
MCB
150A
MCB
No
150A
MCB
Date
Revision
Drawn By:
Checked By:
Proj. #:
CSArch Proj. #:
Date:
150A-3P
150A-3P
DS-1
EL L
2
200A-3P
#4/0 GND
N
3
PP-1
PP-2
LP-1
(ELEC. RM.) (ELEC. RM.) (ELEC. RM.)
800A-3P
800AF/800AT
DEA
4
150A-3P
200A-3P
C
OF NEW Y
OR
F
NY PROFESSIONAL ENGINEER
NO. 073084-1
250A-3P
NEW 800A FUSED
DISCONNECT WITH
CLASS L TIME
DELAY FUSE
TE
R
EX
C E L S IO
D
1.
150A-3P
200A-3P
TA
SE
NOTES:
150A-3P
END OF RGS
HP 2610-24-PWR 10/100 POE 2 GIG 2SFP L
5' RJ-45 CAT-5E + PATCH CORD
SECOND FLOOR
MDP (ELEC. RM.)
800A-3P
ERIC D. FELLENZER
R
150A
MCB
25 PAIR 30 FOOT FEMALE TAIL
GROUND CLAMP
89B BRACKET
66M 1-50 BLOCK
GROUND CABLE
POWER ARRESTER
ZE
(4)#1/0, (1)#6 GND
IN 2" CONDUIT
G
By
Author
Checker
811-11-01
10/30/12
Sheet Title
FIRST FLOOR
2'-6" MIN.
START
OF RGS
SERIES 5000
840.0819
L I C EN
PVC & RGS BY
ELECTRICAL
CONTRACTOR
MITEL
K
(4)#250 MCM, (1)#2
GND IN 3" CONDUIT
NEW 200 KW
120/208 VOLT
3 PHASE 4W DIESEL
GENERATOR
(INSTALLED BY E.C.)
LEAVE SUFFICIENT SLACK FOR
CONNECTION BY UTILITY COMPANY
1 : 580.1003 MT5000 HX CONTROLLER CHASSIS ONLY
1 : 580.3000 MT5000 HX PROCESSOR Mdl (HPM)
16 : 840.0416 MT5000 LIC IP PHONE CATEGORY D
1 : 840.0844 MT5000 LIC DYN EXT EXPR SYSTEM
1 : 50006271 PWR CRD C13 10A 125V - NA PLUG
1 : 580.9126 MT5000 HX CTRL PWR SUP 120W 24VDC 5A
4 : 840.0411 LICENSE INTL5000 BVM SINGLE PT
1 : 999.9000 99.9000
1 : 54005357 MT5000 LIC UVM E-MAIL SYNCHRONIZATION
1 : 54005359 MT5000 LIC MEET-ME CONF
1 : 54005399 MT5000 LIC HOT DESKING SYSTEM - WIDE
1GB COMPACT FLASH MITEL 5000 NA
INSTALLATION
HARDWARE
REMOTE ANNUNIATOR:
NFPA 110 COMPLIANT
UTILITY POLE
SLIDING GATE MAGNETIC LOCK 120V/1 DIAMETER
841.1152
GENERATOR SET:
BATTERIES
BATTERY CHARGER
BATTERY RACK
COOLANT DRAIN EXTENSION
MAIN LINE CIRCUIT BREAKER (800A, 3P)
OIL DRAIN EXTENSION
SOUND ANTINUATION ENCLOSURE W/ CRITICAL GRADE SILENCER
LEVEL 2 SOUND ENCLOSURE TO ALLOW 73 Db AT 23 FT.
2 YEAR STANDBY WARRANTY
* ALL VALUES 208 VOLT, RMS SYMMETRICAL, LESS THAN 20% POWER FACTOR
SPEAKER FOR PHONE INTERCOM. PROVIDE BACK BOX AND CONDUIT
WITH PULL STRING TO ABOVE CEILING HEIGHT.
HIGH BAY OCCUPANCY SENSOR WITH PASSIVE INFRARED TECHNOLOGY,
LOW VOLTAGE, 68' DIAMETER COVERAGE. PROVIDE WITH MODEL #:B120E
POWER PACK (ONE FOR BOTH) AND JUNCTION BOX ADAPTOR PLATE.
ENGINE:
208 VOLT, 2000 WATT COOLANT HEATERS
CONTROL PANEL:
DETECTOR 12 CONTROL (NFPA 110 COMPLIANCE)
EMERGENCY STOP
LOW BATTERY VOLTAGE WARNING
LOW COOLANT LEVEL WARNING/SHUTDOWN
OIL PRESSURE GAUGE
REMOTE FAULT SIGNAL PACKAGE
WATER TEMPERATURE GUAGE
125 KHZ WALL SWITCH SECURITY PROXIMITY READER. PROVIDE BACK
BOX AND CONDUIT WITH PULL STRING TO ABOVE CEILING HEIGHT.
HB-150-4CP-1
ADDITIONAL REQUIREMENTS:
ALTERNATOR:
105°C RISE ALTERNATOR
ANTI-CONDENSATION HEATER
EXTENDED STACK (FULL SINGLE PHASE OUTPUT)
PERMANENT MAGNET EXCITATION
HARDWIRED ELECTRONIC LOCK WITH PROXIMITY READER.
WATTSTOPPER
H
VIC
NOTE:
CONDUIT TO ABOVE CEILING
DUAL TECHNOLOGY, PASSIVE INFRARED AND ULTRASONIC, OCCUPANCY
SENSOR, CEILING MOUNTED, LOW VOLTAGE. POWER WITH MATCHING
POWER PACK TYPICAL OF WATTSTOPPER MODEL# BZ-150.
(2) 28W T5
120W
LED
3/ "
4
DT-300
OS
S
SPRING DRIVEN ELECTRIC CABLE REEL. MOUNT TO CEILING. PROVIDE
WITH 45' OF 12Awg CABLE AND SINGLE 20A, 3 WIRE RECEPTACLE.
WATTSTOPPER
OS
49W LED
ARRAY
DUPLEX SPECIFICATION GRADE GROUND FAULT INTERRUPTER TYPE
3-WIRE GROUNDING RECEPTACLE, PROVIDE WITH FACE PLATE,
20A,125V. COORDINATE FINISH WITH ARCHITECT. MOUNT 18"AFF.
19 Front St., Newburgh, New York 12550
845.561.3179 FAX 845.561.3215
www.csarchpc.com
----
(3) 42W C.F.
S6012440
MC1250K8
SMS24INT-1W
Arch
UNLESS OTHERWISE NOTED.
F
3.07 THE AUTOMATIC TRANSFER SWITCH SHALL BE PROTECTED BY 5
YEAR MANUFACTURERS WARRANTY.
Architecture Engineering Construction Management
----
181 Church St., Suite 100,
Poughkeepsie, NY 12601
t 845-454-9704 fx 845-454320-8735
LIS64GPN4OULAG
----
U.O.N.
22 Mulberry St., Suite 2A,
Middletown, NY 10940
t 845-343-1481 fx 845-343-4986
TRANSFER SWITCH NORMALLY CONNECTS AN ENERGIZED UTILITY POWER
SOURCE (SOURCE 1) TO LOADS AND A GENERATOR SET (SOURCE 2)
TO THE LOADS WHEN NORMAL SOURCE FAILS. THE NORMAL POSITION
OF THE TRANSFER SWITCH IS SOURCE 1 (CONNECTED TO THE UTILITY),
AND NO START SIGNAL IS SUPPLIED TO THE GENERATOR.
E
LIGHTOLIER
NEW HOME RUN TO PANEL AS INDICATED.
NEER
2.01
D
44W LED
ARRAY
----
GI
2.0 SEQUENCE OF OPERATION
R3-WG-2L40
-1C-120-24-T1
C
2'x2' SHIELDED RECESSED LED FIXTURE. RECTANGULAR PERF INLAY
SHEILD WITH 4000K LED LAMP. 120V.
----
EN
1.05 THE WITHSTAND CURRENT OF THE MAIN CONTACTS SHALL
NOT BE LESS THAN 20 TIMES THE CONTINUOUS DUTY RATING
AS ESTABLISHED BY TEST DATA.
* AUXILIARY CONTACT CLOSED IN EMERGENCY POSITION
* AUXILIARY CONTACT CLOSED IN NORMAL POSITION
* ENGINE START CONTACT, 1 N.O., 1 N.C.
* PILOT LIGHT TO INDICATE SWITCH IN EMERGENCY POSITION
* PILOT LIGHT TO INDICATE EMERGENCY SOURCE AVAILABILITY
* ADJUSTABLE TIME DELAY ON RETRANSFER TO NORMAL, 0-30 MIN
* ADJUSTABLE TIME DELAY ON TRANSFER TO EMERGENCY, 0-30 MIN
* ADJUSTABLE TIME DELAY ON ENGINE START, .5-6 SECONDS
* ADJUSTABLE TIME DELAY FOR ENGINE COOL DOWN, 0-30 MIN
* LOAD TEST SWITCH
* TRANSITION MODE SELECTOR SWITCH TO ALLOW OPEN OR CLOSED
TRANSITION TRANSFER.
* ALARM AND SHUNT TRIP CIRCUIT WITH DIAGNOSTIC INDICATORS
* EXTENDED PARALLEL ELECTRICAL OPERATOR REVERSAL
SAFETY CIRCUIT AND LOCKOUT
R3-WG-2L40
-1C-120-22-T1
EMERGENCY EXIT SIGN, RED LETTERS, WHITE BACKGROUND,
THERMOPLASTIC HOUSING.
ENGINEERING LLP
1.04 AS A PRECONDITION FOR APPROVAL, ALL TRANSFER SWITCHES
SHALL BE LISTED BY UNDERWRITERS LABORATORIES, UNDER
STANDARD UL 1008 (AUTOMATIC TRANSFER SWITCHES) AND
APPROVAL FOR USE ON EMERGENCY SYSTEMS.
COOPER
LIGHTING
B
----
JOB# 09-167B
1.03 THE UNIT SHALL BE RATED BASED ON ALL CLASSES OF LOADS:
I.E., RESISTIVE, TUNGSTEN, BALLAST, AND INDUCTIVE LOADS.
SWITCHES RATED AT 800A OR LESS SHALL BE UL LISTED FOR 100%
TUNGSTEN LAMP LOADS.
3.06 THE CLOSED TRANSITION TRANSFER SWITCH SHALL INCLUDE THE FOLLOWING
STANDARD EQUIPMENT:
(3) 42W C.F.
DESCRIPTION
I
1.02 THE CURRENT RATING SHALL BE A 800A CONTINUOUS RATING
WHEN THE SWITCH IS INSTALLED IN AN UNVENTILATED ENCLOSURE,
AND SHALL CONFORM TO NEMA TEMPERATURE RISE STANDARDS.
A3
SAME AS FIXTURE ABOVE EXCEPT MOUNTED WITH A LONGER
CONNECTION TO BE 18'-9" FROM FINISHED FLOOR AND PARALLEL TO
OTHER FIXTURES.
SAME AS FIXTURE ABOVE EXCEPT MOUNTED WITH A LONGER
CONNECTION TO BE 18'-9" FROM FINISHED FLOOR AND PARALLEL TO
OTHER FIXTURES.
MCPHILBEN
MODEL NO.
S
1.01 THE AUTOMATIC OPEN TRANSITION TRANSFER SWITCH
SHALL BE RATED FOR 208Y/120V, 3PH, 3P, SOLID NEUTRAL,
800A, AND SHALL HAVE 600 VOLT INSULATION ON ALL
PARTS IN ACCORDANCE WITH NEMA STANDARDS.
3.05 SWITCHED COMPOSED OF MOLDED CASE BREAKERS, CONTACTORS OR COMPONENTS
THEREOF NOT SPECIFICALLY DESIGNED AS AN AUTOMATIC TRANSFER SWITCH
WILL NOT BE ACCEPTABLE.
(3) 42W C.F.
MANUFACTURER
ER
1.0 GENERAL
A2
"REFRACTOR" PENDANT MOUNT LIGHTING FIXTURE. ALUMINUM BODY
WITH HIGH TEMPERATURE CLEAR PRISMATIC ACRYLIC REFRACTOR AND
GLASS DECORATIVE DISK. 120V MOUNTED 18'-9" FROM FINISHED FLOOR.
SYMBOL
SOUTH SPRING VALLEY FIRE DISTRICT
NEW FIRE HOUSE
CHESTNUT RIDGE, NY
3.04 THE SWITCH SHALL BE MOUNTED IN NEMA 1 ENCLOSURE UNLESS OTHERWISE
INDICATED IN PLANS.
LAMPS
DESCRIPTION
Consultant
BELARO 22
20 2202-1
BETA-CALCO
A1
MODEL NO.
Project Title
208Y/120V, 3 , 4W, 800A, 3 POLE. SOLID
NEUTRAL
MANUFACTURER
S
SYMBOL
3.03 A MANUAL HANDLE SHALL BE PROVIDED FOR MAINTENANCE PURPOSES
WITH THE SWITCH DE-ENERGIZED. AN OPERATOR DISCONNECT SWITCH
SHALL BE PROVIDED TO DEFEAT AUTOMATIC OPERATION DURING MAINTENANCE,
INSPECTION OR MANUAL OPERATION.
LEGEND AND SCHEDULE OF ELECTRICAL EQUIPMENT
S
TYPE: OPEN TRANSITION AUTOMATIC
MAKE: TRANSFER SWITCH (ATS)
ASCO
LEGEND AND SCHEDULE OF LIGHTING EQUIPMENT
3.02 A DIELECTRIC TEST AT THE CONCLUSION OF THE WITHSTAND AND CLOSING TESTS
SHALL BE PERFORMED.
S
AUTOMATIC TRANSFER SWITCH SPECIFICATIONS
13.2 KV (3)#2 PRIMARY WITH
CONCENTRIC NEUTRALS IN
4" SCH. 80 PVC CONDUIT
2 SETS OF: (4)#600 MCM IN 4"
SCH. 80 PVC CONDUIT
2 SETS OF: (4)#600 MCM
(1)#1/0 GND IN 4" CONDUIT
NEW 800A
SERVICE
ENTRANCE
RATED OPEN
TRANSITION ATS
SPARE
(4)#4/0, (1)#2 GND
IN 2 1/2" CONDUIT
(4)#4/0, (1)#6 GND,
(1)#6 IG IN 2"
CONDUIT
ELECTRICAL
SCHEDULES
NEW 208 VOLT 800 AMP SQUARE
'D' TYPE 'HCM' I-LINE PANEL
NOTES:
1.
ELECTRICAL CONTRACTOR RESPONSIBLE FOR SECONDARY CONDUCTORS, CONDUITS, TRANSFORMER PAD AND
INSTALLATION. UTILITY COMPANY RESPONSIBLE FOR CONNECTION AT POLE AND PAD MOUNT TRANSFORMER.
2.
METER BY UTILITY COMPANY. METER ENCLOSURE & METERING BY ELECTRICAL CONTRACTOR.
1
Sheet No.
E-801
ELECTRICAL ONE-LINE DIAGRAM
N.T.S.
COPYRIGHT
zALL
RIGHTS RESERVED
ISSUE FOR BID