Universal Remote
Alarm Buzzer
General Specifications:
The Amico Universal Remote Alarm Buzzer will provide the user
with the ability to receive an audible alarm, and a visual alarm
from a remote dry contact signal. If an alarm condition occurs,
the “RED” alarm LED shall flash and the audible alarm will sound.
Pushing the “ALARM SILENCE” button will cancel the audible
alarm, but the unit will remain in the visual alarm condition
until the problem is rectified.
The M2-REM-AL-NEMA includes a built in power supply that
accepts 110 V AC to 240 V AC (50 to 60 Hz) as the input voltage.
The output voltage is 12V DC.
M2-REM-AL-WALL
The M2-REM-AL-N2 includes two remote buzzers and a power
supply that accepts 110 V AC to 240V AC (50 to 60 Hz) as the
input voltage and an output voltage of 12V DC.
The M2-REM-AL-WALL and M2-REM-AL-SURF if used with an
Amico Alert-2 Manifold or Alarm does not require a power
supply if the distance between the Universal Remote Buzzer
and the Manifold or Alarm is less than 60 ft. If the distance is
greater than 60 ft, an external power supply (A2P-POWER-CONV)
or a 12 volt DC voltage is required.
M2-REM-AL-SURF
Features:
M2-REM-AL-NEMA
The Remote Alarm Buzzer can be used in the
following separate functions:
• A device sending a dry contact signal.
• An Amico Alert-2 area or master alarm.
• An Alert-2 manifold bank switch-over occurs.
M2-REM-AL-N2
1
Technical Specifications
M2-REM-AL-WALL
Inch
[mm]
2“
2
[51]
[51]
5
5“
[127]
[127]
annunciator wiring
schematic
wiring schematic
44“
[101]
[101]
AC
Supply
AC Supply
120 VAC
VAC
120
Power Supply
Optional
Power
Supply
12V DC
+
+
Optional: To
To Amico
Universal
Optional:
Amico
Universal
Remote Buzzer
Remote Buzzer
REMOTE BUZZER
Optional Signal
Optional
Signal
Device
Device
Dry Contact
--
+12V
+12V
C NO
NO
NC
C
NC
+
5.5
5.5“
[139.7]
[139.7]
S
-
M2-REM-AL-SURF
+
REMOTE BUZZER
S
3 3“
[76.2]
[76.2]
-
2-7/8“
2-7/8
[73]
[73]
NO NC COM GND +12V
4-7/16“
4-7/16
[112.71]
[127]
Power Supply: A2P-POWER-CONV
NOTE: Power supply not included with wall & surface mount
wiring schematic
44“
[101.6]
[101.6]
66“
[152.4]
[152.4]
annunciator wiring
schematic
AC Supply
Supply
AC
G
G
66“
[152.4]
[152.4]
N
L
Optional:
To Amico
Optional:
To Amico
UniversalUniversal
Remote
BuzzerBuzzer
Remote
Power Supply
Power Supply
Optional
Signal
Dry Contact
Device
12V DC
+
+
--
NO NC
NC
CC NO
Power
Power Supply
Supply
12V DC
++
--
REMOTE BUZZER
+
+12V
REMOTE BUZZER
+
M2-REM-AL-NEMA
S
-
S
-
M2-REM-AL-N2
NO NC COM GND +12V
R1
R1
R2
R2
REMOTE BUZZER
REMOTE BUZZER
+
44“
[101.6]
[101.6]
S
-
+
8 8“
[203.2]
[203.2]
S
-
66“
[152.4]
[152.4]
G R2
R2 R1
R1
G
Optional Signal
Device
Dry Contact
+
+
-Power Supply
Power
Supply
12V DC
NOTE: The Manifold can be
connected from Normally
Open to R1 or R2, but all
appropriate
connections
(Common) should be
made to Ground.
AC
Supply
AC Supply
120
120VAC
VAC
Amico Corporation 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada I 71 East Industry Court, Deer Park , NY 11729, USA
Toll Free Tel: 1.877.462.6426 | Toll Free Fax:1.866.440.4986 Tel: 905.764.0800 | Fax: 905.764.0862
AL_SP_MED_GAS_MANIFD_RMT_ALRM PRINTED APR 09
www.amico.com
2