MC33174 - MC35174
LOW POWER
QUAD BIPOLAR OPERATIONAL AMPLIFIERS
■ GOOD CONSUMPTION/SPEED RATIO :
ONLY 200µA FOR 2.1MHz, 2Vµs
■ SINGLE (OR DUAL) SUPPLY OPERATION
FROM +4V TO +44V (±2V TO ±22V)
■ WIDE INPUT COMMON MODE MODE
VOLTAGE RANGE INCLUDING VCC-
N
DIP14
(Plastic Package)
■ LOW LEVEL OUTPUT VOLTAGE CLOSE TO
VCC- : 100mV TYPICAL
■ PIN TO PIN COMPATIBLE WITH
STANDARD QUAD OP-AMPs
DESCRIPTION
The MC3x174 series are quad bipolar operational
amplifier offering both low consumption (200µA)
and good speed (2.1MHz, 2V/µs).
Moreover the Input Common Mode Range extends down to the lower supply rail, allowing single
supply operation from +4V to +44V.
D
SO14
(Plastic Micropackage)
PIN CONNECTIONS (top view)
ORDER CODE
Output 1 1
Part Number
Temperature
Range
MC33174
-40°C, +105°C
MC35174
-55°C, +125°C
Example : MC33174N
Package
N
•
•
14 Output 4
Inverting Input 1 2
-
-
13 Inverting Input 4
D
Non-inverting Input 1 3
+
+
12 Non-inverting Input 4
•
•
VCC + 4
11 VCC -
Non-inverting Input 2 5
+
+
10 Non-inverting Input 3
Inverting Input 2 6
-
-
9
Inverting Input 3
8
Output 3
Output 2 7
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT))
April 2002
1/5
MC33174-MC35174
SCHEMATIC DIAGRAM (for 1/4 MC33174)
VCC +
R5
R4
T7
T8
R6
T10
T9
T1
R7
T13
T12
T11
R8
T25
R3
T16
T15
T6
Input -
Input +
T24
T26
T17
R13
T14
Output
R12
C
T22
T5
R14
T13
T2
T21
T19
T28
T27
T20
T3
T29
T4
T23
R2
R1
R10
R9
R11
T30
R15
T31
VCC -
MAXIMUM RATINGS
Symbol
Value
Unit
±22
V
VCC
Supply Voltage
Vid
Differential Input Voltage
see note 1)
V
Vi
Input Voltage
Output Short Circuit Duration
Operating Free-Air Temperature range
see note 1
Indefinite
-40 to 105
-55 to 125
V
s
Toper
1.
Parameter
MC33174
MC35174
°C
Tj
Junction Temperature
150
°C
Tstg
Storage Temperature
-65 to 150
°C
Value
Unit
±2 to ±22
V
Either or both input voltages must not exceed the magnitude of Vcc.
OPERATING CONDITIONS
Symbol
VCC
2/5
Parameter
Supply Voltage
MC33174-MC35174
ELECTRICAL CHARACTERISTICS
VCC+ = +15V, VCC- = -15V, R L connected to Ground, Tamb = 25°C (unless otherwise specified)
Symbol
Vio
Parameter
Min.
Input Offset Voltage
VCC+ = +15V, VCC- = -15V, Vic = 0V
VCC+ = 5V, VCC- = 0V, Vic = 0V, Vo = 1.4V
Typ.
Max.
1
1
4.5
5
6.5
VCC = +15V, VCC = -15V, Vic = 0V, Tmin. ≤ Tamb ≤ Tmax.
+
DVio
-
Input Offset Voltage Drift
10
Iio
Input Offset Current (Vic = 0V)
Tmin. ≤ Tamb ≤ Tmax.
5
Iib
Input Bias Current (Vic = 0V)
Tmin. ≤ Tamb ≤ Tmax.
Avd
VOH
Large Signal Voltage Gain (RL = 10kΩ, Vo = ±10V)
Tmin. ≤ Tamb ≤ Tmax.
High Level Output Voltage
VCC+ = 5V, VCC- = 0V, RL = 10kΩ
VCC+ = +15V, VCC- = -15V, RL = 10kΩ
VCC = +15V, VCC = -15V, RL = 10kΩ, Tmin. ≤ Tamb ≤ Tmax
+
VOL
-
20
50
25
100
3.5
13.6
13.3
4.2
14.2
Low Level Output Voltage
VCC+ = 5V, VCC- = 0V, RL = 10kΩ
0.1
-14
VCC+ = +15V, VCC- = -15V, RL = 10kΩ
VCC+ = +15V, VCC- = -15V, RL = 10kΩ, Tmin. ≤ Tamb ≤ Tmax
Isc
Output Short Circuit Current (Vid = ±1V, Vo = 0V)
Source
Sink
3
15
Unit
mV
µV/°C
20
40
nA
100
200
nA
V/mV
V
0.15
-13.6
-13.3
6
27
V
mA
VCC- to (VCC+ - 1.8)
Vicm
Input Common Mode Voltage Range
Tmin. ≤ Tamb ≤ Tmax
CMR
Common-mode Rejection Ratio (Vic = Vicm min.)
80
100
dB
SVR
Supply Voltage Rejection Ratio (VCC = ±5 to ±15V)
80
100
dB
ICC
V
VCC- to (VCC+ - 2.2)
Supply Current
VCC+ = 5V, VCC- = 0V, no load
200
220
VCC+ = +15V, VCC- = -15V, no load
VCC+ = +15V, VCC- = -15V, no load, Tmin. ≤ Tamb ≤ Tmax
SR
GBP
250
250
300
µA
Slew Rate (Vi = ±10V, RL = 10kΩ, CL = 100pF)
1.6
2
V/µs
Gain Bandwidth Product
RL = 10kΩ, CL = 100pF, f = 100kHz
1.4
2.1
MHz
φm
Phase Margin (RL = 10kΩ, CL = 100pF)
45
Degrees
en
Equivalent Input Noise Voltage (f = 1kHz)
29
nV
-----------Hz
0.05
%
120
dB
THD
Total Harmonic Distortion
VO1/VO2 Channel Separation
3/5
MC33174-MC35174
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC DIP
Millimeters
Inches
Dimensions
Min.
a1
B
b
b1
D
E
e
e3
F
i
L
Z
4/5
Typ.
0.51
1.39
Max.
Min.
1.65
0.020
0.055
0.5
0.25
Typ.
0.065
0.020
0.010
20
0.787
8.5
2.54
15.24
0.335
0.100
0.600
7.1
5.1
0.280
0.201
3.3
1.27
Max.
0.130
2.54
0.050
0.100
MC33174-MC35174
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC MICROPACKAGE (SO)
G
c1
s
e3
b1
e
a1
b
A
a2
C
L
E
D
M
8
1
7
F
14
Millimeters
Inches
Dimensions
Min.
A
a1
a2
b
b1
C
c1
D (1)
E
e
e3
F (1)
G
L
M
S
Typ.
Max.
Min.
1.75
0.2
1.6
0.46
0.25
0.1
0.35
0.19
Typ.
0.069
0.008
0.063
0.018
0.010
0.004
0.014
0.007
0.5
Max.
0.020
45° (typ.)
8.55
5.8
8.75
6.2
0.336
0.228
1.27
7.62
3.8
4.6
0.5
0.344
0.244
0.050
0.300
4.0
5.3
1.27
0.68
0.150
0.181
0.020
0.157
0.208
0.050
0.027
8° (max.)
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2002 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia
Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States
© http://www.st.com
5/5