10 Output Power
Supply Panel
Installation
Instructions
CSPS-P1-10-6
CSPS-P1-10-6
English
Input: 120-240 V
50/60 Hz 1.5 A
Output: 12 V
5A
Weight: 8.5 lb
cULus Listed (E135084)
Installation Instructions (save these instructions)
Read and Follow all instructions.
Tools Required:
Wire Cutter/Stripper
#2 Flat-Head Screwdriver
Power Drill
#2 Phillips Screwdriver
NOTE: Mounting hardware is not included due to the wide variety of wall materials.
Customer should determine the appropriate mounting hardware for their specific needs.
Box Contents:
CSPS-P1-10-6
1
1.1
The 10 Output Power Supply Panel is a permanently
installed power supply for use with Lutron Insulating
Honeycomb Shades. CSPS-P1-10-6 simplifies the wiring
and organizes installations that require multiple power
supplies. Each panel provides ten 12 V- Class 2 outputs
for Lutron Insulating Honeycomb Devices.
Important Notes
1. All wiring must be in accordance with national and local electrical codes.
2. Note: Secondary wiring must be of type CL2, CL2P, CL2R, CL2X or other cable with equivalent
or better electrical, mechanical, and flammability ratings in accordance with all local and national
electric codes.
3. CSPS-P1-10-60 must be installed by a qualified electrician.
4. Ambient operating temperature: 32 to 104 °F (0 to 40 °C), 0 - 90% humidity,
non-condensing.
5. This product is intended for indoor use only.
No maintenance required.
6. This panel is not compatible with Sivoia QED, Sivoia QS, or any other non-honeycomb devices.
Page 2
Cellular Shade Power Panel
CSPS-P1-10-6
Installation instructions
2
2.1
Installation
English
1. Remove metal outer panel cover and inner plastic line voltage shield.
2. Choose panel mounting location so line voltage wiring is at least 6 ft (1.8 m) from audio or
electronic equipment and associated wiring (prevents radio frequency interference).
3. Surface Mount - Use the four holes located on the back of the enclosure in each corner
to fasten the CSPS-P1-10-6 to the wall. Use fasteners rated for a 25 lb (11,3 kg) load.
•
•
•
•
•
•
Notes:
Mount the Power Panel in a position where it can be easily located and accessed if service
or troubleshooting is necessary.
Mount the CSPS-P1-10-6 in the orientation shown (Mounting Hardware is not provided).
Do not mount in any other orientation.
For indoor use only.
NEMA, Type 1 enclosure, IP20.
Install in accordance with all national and local electrical codes.
Can be installed in accordance with National Electrical Code® (NEC®) Article 300.22(c)
“Other places used for environmental air”.
9.25 in
(234,95 mm)
1.66 in
(42,16 mm)
1.31 in
(33,27 mm)
1.22 in
(30,99 mm)
3.16 in
(80,26 mm)
7.50 in
(190,50 mm)
0.88 in
(22,35 mm)
1.22 in
(30,99 mm)
1.00 in
(25,40 mm)
Line Voltage Shield
11.25 in
(285,75 mm)
13.25 in
(336,55 mm)
0.20 in
(5,16 mm) dia.
Page 3
Cellular Shade Power Panel
CSPS-P1-10-6
Installation instructions
3
Primary Wiring
3.1
WARNING
English
SHOCK HAZARD. Risk of serious injury or death. Locate and lock the supply breaker in the OFF
position before wiring to the terminal blocks. If the line voltage shield is not securely covering the
input wiring, the unit must be accessed by a certified electrician, following local codes.
Note: Maximum of 5 CSPS-P1-10-6 power supplies per 15 A Breaker.
Note: All Primary wiring must be 16 AWG - 12 AWG copper wire rated for 75 ˚C or better.
The CS Power Panel operates at 120-240 V . Use the following instructions to wire line voltage
to the unit.
1.
2.
3.
4.
Turn power off at circuit breaker.
Remove metal outer panel cover.
Remove internal plastic line voltage shield.
Use 16 AWG to 12 AWG (1,5 mm2 to 4,0 mm2) conductors (in accordance with circuit
breaker rating) for the input wiring.
5. Wire the line voltage wires to the terminals labeled H (Hot), N (Neutral) and (Ground).
Tighten the terminal blocks to 3.5 - 5 in•lb (0,4 - 0,6 N•m).
6. Reinstall the internal plastic line voltage shield.
Page 4
Cellular Shade Power Panel
CSPS-P1-10-6
Installation instructions
4
4.1
Secondary Wiring
English
WARNING
SHOCK HAZARD. Risk of serious injury or death.
Locate and lock the supply breaker in the OFF position
before wiring to the terminal blocks. If the line voltage
shield is not securely covering the input wiring, the unit
must be accessed by a certified electrician, following
local codes.
Note: All secondary wiring must be of type CL2, CL2P,
CL2R, CL2X or other cable with equivalent or better
electrical, mechanical, and flammability ratings in
accordance with local and national electric code.
Common
(Black terminals)
+12V
(Red terminals)
1. Turn off power at the circuit breaker.
2. Remove as many knockout tabs as neccessary
from the bottom of the enclosure and insert 0.75 in
(19 mm) strain reliefs (not included) into the open
knockout holes.
3. Route the secondary wire through the strain reliefs
and to the output terminal blocks.
4. Strip the secondary wire insulation so that 0.25 in
(7 mm) of bare wire is exposed. Insert the Common
leads into the Black Terminal Blocks and the +12 V
leads into the Red Terminal Blocks. Tighten the terminal blocks to 3.5 - 5 in•lb (0,4 - 0,6 N•m). Make
sure the wire insluation is not pinched.
5. Place the metal cover securely back onto the
enclosure and tighten the screws.
5. Restore power to the panel.
4.2 Wire Length Chart
Use this chart to determine the maximum wire length, from panel to
shade, based on the gauge of the wire that is used.
Distance to
shade
16 AWG
(1.5 mm2)
18 AWG
(1 mm2)
20 AWG
(0.5 mm2)
200 ft (60 m)
125 ft (35 m)
75 ft (22 m)
Page 5
Cellular Shade Power Panel
CSPS-P1-10-6
Installation instructions
5
5.1
Shade Wiring
English
WARNING
SHOCK HAZARD. Risk of serious injury or death. Locate and lock the supply breaker in the OFF
position before wiring to the terminal blocks. If the line voltage shield is not securely covering the
input wiring, the unit must be accessed by a certified electrician, following local codes.
1. Turn off power at the circuit breaker.
2. Route the secondary wiring to the shade so the connection to the shade wiring can be
concealed in the shade headrail. Secondary wiring may be routed into the headrail either by
dropping the wire in through the top of the headrail, or drilling a hole in the shade endcap.
3. Identify the shade wiring cable. This is a 15 foot cable attached to the shade headrail.
4. Clip the shade wiring cable so that no more than three feet of the cable is connected to
the shade.
5. Remove 0.5 in (13 mm) of the outer insulation from the shade cable to expose the red and black
wires inside.
6. Remove 0.25 in (6,3 mm) of the inner insulation from both the red and black wires.
7. Connect the secondary wires to the shade cable using wire connectors. Connect the red shade
wire to the +12V lead of the secondary wiring. Connect the black shade wire to the common of
the secondary wiring.
Note: The shade wiring cable is housed in the left side of the headrail (see diagram below). If
you want to connect the secondary wires to the shade cable in the right side of the headrail, you
must run the cable out of the headrail, past the shade motor, and then back into the right side
of the headrail. Leave at least 0.25 in (6,3 mm) clearance between shade cable and antenna to
ensure proper RF perfomance.
8. Replace the metal panel cover and tighten the screws.
9. Restore power to the CS Power Panel and confirm that the shade is energized.
Refer to the Insulating Honeycomb Shade Installation and Programming guide for programming and
operating instructions.
Line Voltage Shield
+12 V
(Red Wire)
Shade Wiring
Cable
Common
(Black Wire)
Connect the secondary wiring to the
shade wiring cable via wire connectors.
- Connection should be concealed
within headrail
Page 6
Cellular Shade Power Panel
CSPS-P1-10-6
M h
i l Di
i
Installation instructions
Technical Assistance
WORLDWIDE
HEADQUARTERS - USA
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
TEL: +1.610.282.3800
FAX: +1.610.282.1243
Technical support: 1.800.523.9466
Toll-free: 1.888.LUTRON1
intsales@lutron.com
ASIAN HEADQUARTERS
Lutron GL Ltd.
15 Hoe Chiang Road
#07-03 – Tower Fifteen
Singapore 089316
TEL: +65.6220.4666
FAX: +65.6220.4333
Technical support: 800.120.4491
lutronsea@lutron.com
English
ADDITIONAL SALES OFFICES:
Germany
TEL: +49.(0)30.9710.4590
FAX: +49.(0)30.9710.4591
FREEPHONE: 00800.5887.6635
lutrongermany@lutron.com
France
TEL: +33.(0)1.56.52.93.01
FAX: +33.(0)1.56.52.93.02
FREEPHONE 0800.90.12.18
lutronfrance@lutron.com
Spain, Madrid
FAX: +34.91.567.84.78
FREEPHONE: 900.948.944
lutroniberia@lutron.com
Spain, Barcelona
TEL: +34.93.496.57.42
FAX: +34.93.496.57.01
FREEPHONE: 900.948.944
lutroniberia@lutron.com
EUROPEAN
HEADQUARTERS
Lutron EA Ltd.
6 Sovereign Close
London, E1W 3JF, UK
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Technical support: +44.
(0)20.7680.4481
FREEPHONE: 0800.282.107
www.lutron.com/shadingsolutions
USA and Canada (24 hrs/7days):
call:
800.523.9466
Other countries (8 a.m. – 8 p.m. ET)
call:
+1.610.282.3800
fax:
+1.610.282.3090
email:
shadinginfo@lutron.com
Lutron and the sunburst logo are
registered trademarks of
Lutron Electronics Co., Inc.
NEC and National Electrical Code
are registered trademarks of National
Fire Protection Association,
Quincy, Massachusetts.
© 2012 Lutron Electronics Co, Inc.
Printed in the USA
P/N 045-348 Rev. C 04/2012
China, Hong Kong
TEL: +852.2104.7733
FAX: +852.2104.7633
Technical support: 800.901.849
lutronhk@lutron.com
China, Beijing
TEL: +86.10.5877.1818
FAX: +86.10.5877.1816
lutronchina@lutron.com
CUSTOMER SERVICE/
ORDERING
UK +44.(0)20.7702.0657 –
09.00 - 18.00 GMT
USA +1.610.282.-3800 –
08.00 - 20.00 EST
Japan
TEL: +81.3.5575.8411
FAX: +81.3.5575.8420
FREEPHONE: 0120.083.417
asuka@lutron.com
CUSTOMER SERVICE
/E-MAIL
shadinginfo@lutron.com
TECHNICAL SUPPORT
& SERVICES
U.S.A., Canada, and Caribbean:
1.800.523.9466
Mexico: +1.888.235.2910
Central/S. America: +1.610.282.6701
European technical support number:
+44.(0)20.7702.0657
Limited warranty
Number of years from
date of shipment
Percentage of cost of replacement parts
credited by Lutron
Up to 5
100%
More than 5 but not more than 8
50%
More than 8
0%
For more information:
www.lutron.com/technicaldocumentlibrary/window systems warranty.pdf
Cellular Shade Power Panel
CSPS-P1-10-6
Page 7
Installation instructions