www.meade.com
MEADE INSTRUCTION MANUAL
Polaris Series German Equatorial Telescopes
POLARIS SERIES
WARNING!
Never use a Meade® Telescope to look at the Sun!
Looking at or near the Sun will cause instant and
irreversible damage to your eye. Eye damage is often
painless, so there is no warning to the observer that
damage has occurred until it is too late. Do not point the
telescope at or near the Sun. Do not look through the
telescope or viewfinder as it is moving. Children should
always have adult supervision while observing.
INTRODUCTION
Your telescope is an excellent beginner’s
instrument, and is designed to observe
objects in the sky. It can be your personal
window to the universe allowing you to see
bright galaxies, planets, stars and more.
The telescope is shipped with the following
parts:
• Optical tube
• German equatorial mount
• Stainless-steel tripod with accessory tray
• Three 1.25” eyepieces:
MA25mm, MA9mm, MA6.3mm
• Red dot viewfinder with bracket
• Slow-motion control cables
• 90 degree erect-image diagonal prism (Refractors only)
The Polaris Series of telescope includes
optical tubes of different sizes and design.
Some optical tubes use lenses to focus the
incoming light and are called refractors. Other
optical tubes use mirrors to bring the incoming
light to focus and are called reflectors.
The lens or mirror diameter of the telescope
is one of the most important pieces of
information about the telescope. The size of
the lens or mirror, also known as “aperture”,
determines how much detail you will be able
to see in your telescope. The optical tubes
focal length information is also important
and will help later on to calculate the viewing
magnification.
Setting up your telescope involves these
simple steps:
•Setup your tripod
•Attach the accessory tray
•Attach the mount
•Attach the counterweight
counterweight
shaft
•Prepare the mount
•Attach the optical tube to the mount
•Attach the red dot viewfinder
•Attach the eyepiece
and
Study the picture on the next page(s)
and become acquainted with the parts
of your telescope. Figure 1A shows
a typical reflector telescope whereas
Figure 1B shows a refractor. Then
proceed to “Setup your Tripod.”
1
2
FIGURE 1A
1. Tripod legs
2. Large Equatorial Mount
3. Right Ascension control cable
4. Declination control cable
5.Counterweight(s)
6. Counterweight shaft
7. Counterweight lock knobs
8. Counterweight safety knob
9. Latitude adjustment lock (see Fig. 3)
10. Polar axis (see Fig. 3)
11. Latitude adjustment knob
12. Main optical tube (OTA)
13. Optical tube saddle plate (see Fig. 3)
14. Cradle rings
15. Cradle ring lock knobs
16. Red dot viewfinder bracket mounting
thumbscrews (see Fig 4/5)­­­
17.Focuser
18. Focuser thumbscrew
19.Eyepiece
20. Red dot viewfinder On/Off switch
(see Inset B)
21. Declination axis (see Fig. 3)
22. Right Ascension lock (see Fig. 3)
23. Declination lock (see Fig. 3)
24. Red dot viewfinder
25. Front dust cover (not shown)
Figure 1A: Meade Polaris Reflecting Telescope
Inset A:
Accessory Tray
Inset B:
Red Dot Viewfinder Assembly.
Inset C:
Tripod Leg
26. Eyepiece holder slots (see Inset A)
27. Right Ascension setting circle
28. Declination setting circle
29. Latitude dial (see Fig. 3)
30. Azimuth lock
31. Focus knobs
32. Azimuth base (see Fig. 3)
33. Accessory tray (see Inset A)
34. Red dot viewfinder alignment
screws (see Inset B)
35. Leg brace support (see Inset A)
36. Tripod leg lock knob (see Inset C)
37. Sliding leg extension
(see Inset C)
38. OTA saddle plate lock knob(s) (not
visible)
39. Primary Mirror collimation adjustments (not visible)
40. Camera adapter mounting screw
41. Secondary Mirror collimation adjustments
42. Optional motor drive gear (Large EQ
mount only)
Inset A
Inset B
Inset C
FIGURE 1B
1. Tripod legs
2. Small Equatorial Mount
3. Right Ascension control cable
4. Declination control cable
5.Counterweight(s)
6. Counterweight shaft
7. Counterweight lock knobs
8. Counterweight safety knob
9. Latitude adjustment lock (not visible)
10. Polar axis (see Fig. 3)
11. Latitude adjustment knob
12. Main optical tube (OTA)
13. Optical tube saddle plate (see Fig. 3)
14. 90 Degree Erect-Image Prism
15. 90 Degree Prism Thumb screws
16. Red dot viewfinder bracket mounting
thumbscrews (see Fig 4/5)­­­
17.Focuser
18. Focuser thumbscrew
19.Eyepiece
20. Red dot viewfinder On/Off switch
(see Inset B)
21. Declination axis (see Fig. 3)
22. Right Ascension lock (see Fig. 3)
23. Declination lock (see Fig. 3)
24. Red dot viewfinder
25. Front dust cover (not shown)
Figure 1B: Meade Polaris Refracting Telescope
Inset A:
Accessory Tray
Inset B:
Red Dot Viewfinder Assembly.
Inset C:
Tripod Leg
26. Eyepiece holder slots (see Inset A)
27. Right Ascension setting circle
28. Declination setting circle
29. Latitude dial (see Fig. 3)
30. Azimuth lock
31. Focus knobs
32. Azimuth base (see Fig. 3)
33. Accessory tray
34. Red dot viewfinder alignment
screws (see Inset B)
35. Leg brace support (see Inset A)
36. Tripod leg lock knob (see Inset C)
37. Sliding leg extension
(see Inset C)
38. OTA saddle plate lock knob(s) (not
visible)
39. Dew Shield
Inset A
3
Inset B
Inset C
Fig. 2
4
SETUP YOUR TRIPOD
The tripod is the basic support for your
telescope. Its height may be adjusted so that
you can view comfortably. Note: Number in
brackets, e.g., (3), refer to Fig. 1A and 1B
unless noted otherwise. The tripod is shipped
from the factory pre-assembled and needs
only the mount and accessory tray attached.
1.Spread the tripod legs out evenly apart.
2. Set the height of your tripod:
a. Rotate and loosen the tripod leg lock
thumbscrew (36) to unlock the sliding leg
extension (37).
b. Slide the inner portion of the leg (37) in or
out to the desired length.
c. Rotate and tighten the leg lock thumbscrew
(36) to re-lock the inner tripod leg.
d. Repeat for the other two legs so when
complete, the top of the tripod is level.
ATTACH THE ACCESSORY TRAY
using the large azimuth lock knob (30) at the
top of the tripod. Tighten to a firm feel.
ATTACH THE COUNTERWEIGHT SHAFT
AND COUNTERWEIGHT
1. Thread the counterweight shaft (6) into
the mounts declination axis (21, Fig. 3) until
it stops.
The accessory tray attaches at the center of
the tripod legs and is a convenient place to
hold eyepieces and other Meade accessories
while observing, such as the Barlow lens.
To attach, place the hole in the center of the
accessory tray over the attachment point as
shown in Fig 2. Then rotate the tray until the
wings of the tray snap into place on the tripod
leg brace supports.
To remove the tray, rotate the tray so it
unlocks, then remove.
ATTACH THE MOUNT
Next, attach the mount body (2) to the tripod
by placing the base of the mount on top of the
tripod. Next, secure the mount to the tripod
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
2. Remove the safety knob (8) and set aside.
3. Hold the counterweight (5) firmly in one
hand and slide the counterweight onto the
counterweight shaft (6) so it is about 2” from
the bottom of the shaft.
4. Secure in place by tightening the
counterweight lock knob (7).
5. Thread the safety nut (8) into the
counterweight shaft until tight.
Note: Make sure the safety knob (8) always
remains in place on the shaft. This safety
feature prevents the counterweight from
accidentally falling off the shaft.
PREPARE THE MOUNT
1. Attach the flexible cables (3) and (4).
These cables are secured in place with
a firm tightening of the thumbscrews
located at the attachment ends of each
cable.
2. Tilt the polar axis of the telescope to
roughly a 45° angle with the horizon:
Loosen the latitude adjustment lock (9) so
you can move the mount to the desired
position.
3. Turn the latitude adjusting screw (11)
clockwise until the latitude scale (29) on
the side of the mount reads approximately
45°.
4.Re-tighten the latitude adjustment lock
(9) to secure the mount in place.
ATTACH THE OPTICAL TUBE TO THE
MOUNT
1. Lay the optical tube saddle plate (13)
onto the top of the mount as shown in
Fig 1.
2. Tighten the ota saddle plate lock
knob(s) (38) to a firm feel.
ATTACH THE RED DOT VIEWFINDER
An eyepiece (19) has a narrow field of
view. The red dot viewfinder (24) has
a wider field of view, which makes it
easier to locate objects. Once the red
dot viewfinder is aligned to the optical
tube, the red dot can be used to locate
and place objects more easily in the
telescopes eyepiece.
1. Note the two thumbscrews (16, Fig.
4) thread onto two bolts on the optical
tube. Remove the thumbscrews from
the tube.
2. Line up the two holes on the red dot
viewfinder bracket over the two bolts.
Slide the bracket over the bolts with the
viewfinder lens facing the front of the
telescope.
3. Replace the thumbscrews (16) on to
the bolts and tighten to a firm feel.
NOTE: The Polaris 80 and 90 models
use a dovetail to secure the red dot
viewfinder. For these models, slide the
viewfinder bracket into the viewfinder
holder and secure with the single
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
Fig. 3
5
locking screw (16, Fig 5).
Fig. 4
6
Fig. 5
SUN WARNING!
NEVER USE YOUR TELESCOPE
TO LOOK AT THE SUN!
LOOKING AT OR NEAR THE SUN WILL
CAUSE INSTANT AND IRREVERSIBLE
DAMAGE TO YOUR EYE. EYE DAMAGE
IS OFTEN PAINLESS, SO THERE IS NO
WARNING TO THE OBSERVER THAT
DAMAGE HAS OCCURRED UNTIL IT IS
TOO LATE. DO NOT POINT THE TELESCOPE OR ITS VIEWFINDER AT OR NEAR
THE SUN. DO NOT LOOK THROUGH THE
TELESCOPE OR ITS VIEWFINDER AS IT
IS MOVING. CHILDREN SHOULD ALWAYS
HAVE ADULT SUPERVISION WHILE OBSERVING.
to hold the eyepiece securely.
INSERT THE EYEPIECE
(REFLECTOR MODELS ONLY)
1. Slide the MA25mm eyepiece (19) directly
into eyepiece holder on the focuser (17).
2. Tighten the focuser thumbscrew(s) (18)
(REFRACTOR MODELS ONLY)
1. First, slide the 90 degree erect image
prism (14, Fig 1B) directly into the focuser
draw tube (17).
2. Tighten the focuser thumbscrew(s) (18) to
hold the 90 degree prism securely.
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
3. Then, slide the MA25mm eyepiece (19)
directly into 90 degree erect image prism (14,
Fig 1B).
4. Tighten the 90 degree erect image prism
thumbscrew (15, Fig 1B) to hold the eyepiece
securely.
BALANCING THE TELESCOPE
In order for the telescope to move smoothly
on its mechanical axes, it must first be
balanced as follows:
Note: If the counterweight is positioned as
recommended previously then the telescope
is already approximately balanced.
1. Loosen the right ascension lock (22). The
telescope mount will turn freely about the
polar axis. Rotate the telescope about the
polar axis so that the counterweight shaft (6)
is parallel to the ground (horizontal).
2. Loosen the counterweight locking knob
(7) and slide the counterweight (5) along the
shaft (6) until the telescope remains in any
given position without tending to drift up or
down around the polar axis (10).
NOTE: Always re-tighten the counterweight
lock knob (7) before rotating the RA axis
to prevent the counterweight from sliding
unexpectedly. When the telescope is
balanced, proceed to aligning the red dot
viewfinder.
ALIGN THE RED DOT VIEWFINDER
object, such as the Moon or a bright star, and
use the viewfinder’s alignment screws to
make any necessary refinements.
5. When finished, turn off the red dot
viewfinder by rotating the on/off switch(20)
counter-clockwise.
Fig. 6
2. Turn on the red dot viewfinder by turning
the on/off switch(20) clockwise.
3. Look through the red dot viewfinder
(24). Turn one or more of the viewfinder’s
alignment screws (34) until the red dot
is precisely over the same object as you
centered in the eyepiece.
4. Check this alignment at night on a celestial
UNDERSTANDING
OBJECTS MOVE
HOW
7
CELESTIAL
Due to the Earth’s rotation, celestial bodies
appear to move from East to West in a curved
path through the skies.
Perform the first part of this procedure
during the daytime and the last step at night.
1. Point the telescope at an easy-to-find land
object such as the top of a telephone pole or
a distant mountain or tower. Look through
the eyepiece and turn the focuser knob (31)
until the image is sharply focused. Center
the object precisely in the eyepiece’s field
of view.
astronomical objects. Another technique
for locating objects is to use the setting
circles that are provided on your
telescope.
All stars and celestial objects are mapped
onto an imaginary sphere surrounding the
UNDERSTANDING
CELESTIAL
MOVEMENTS AND COORDINATES
Understanding where to locate celestial
objects and how those objects move across
the sky is the key to enjoying the hobby
of astronomy. Most amateur astronomers
practice “star-hopping” to locate celestial
objects. They use star charts or astronomical
software to identify bright stars and star
patterns as “landmarks” in their search for
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
Earth. This mapping system is similar to
the system of latitude and longitude on
Earth surface maps.
and longitude on the celestial sphere. These
lines are known as Right Ascension and
Declination.
In mapping the surface of the Earth,
lines of longitude are drawn between the
North and South Poles and lines of latitude
are drawn in an East-West direction, parallel
to the Earth’s equator. Similarly, imaginary
lines have been drawn to form a latitude
The celestial map also contains two poles
and an equator just like a map of the Earth.
The celestial poles are defined as those two
points where the Earth’s North and South
poles, if extended to infinity, would cross the
celestial sphere. Thus, the North Celestial
Pole is that point in the sky where the North
Pole crosses the celestial sphere. The North
Star, Polaris, is located very near the North
Celestial Pole.
8
Fig. 7­­­
North
Celestial
Pole
(Vicinity of
Polaris)
+90 Déc.
Star
17
18
19
16
20
15
14
13
12
11
ation
clin
De
Celestial
Equator
10
Rotation
of the
Earth
21
22
23
8
4
0
Right
Ascension
South
Celestial
Pole
9
-90 Dec.
1
2
3
0 Dec.
7
6
5
So, just as an object’s position on the
Earth’s surface can be located by its latitude
and longitude, celestial objects may also
be located using Right Ascension and
Declination. For example: You can locate
Los Angeles, California, by its latitude (+34°) and longitude (118°). Similarly, you
can locate the Ring Nebula (also known as
“M57”) by its Right Ascension (18hr) and its
Declination (+33°).
• RIGHT ASCENSION (R.A.): This Celestial
version of longitude is measured in units of
hours (hr), minutes (min), and seconds (sec)
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
on a 24 hour “clock” (similar to how Earth’s
time zones are determined by longitude lines).
The “zero” line was chosen to pass through
the constellation Pegasus, a sort of cosmic
Greenwich meridian. R.A. coordinates range
from 0hr 0min 0sec to 23hr 59min 59sec.
There are 24 primary lines of R.A., located
at 15-degree intervals along the celestial
equator. Objects located further and further
East of the zero R.A. grid line (0hr 0min 0sec)
carry higher R.A. coordinates.
• Declination (Dec.): This celestial version
of latitude is measured in degrees, arcminutes, and arc-seconds (e.g., 15° 27’ 33”).
Dec. locations North of the celestial equator
are indicated with a plus (+) sign (e.g., the
Dec. of the North celestial pole is +90°). Any
point on the celestial equator (such as the
THE MEADE 4M COMMUNITY
You haven’t just bought a telescope, you have embarked on an astronomy adventure that never ends.
Share the journey with others by accepting your free
membership in the 4M community of astronomers.
Go to www.Meade4M.com
to activate your membership today.
constellations of Orion, Virgo, and Aquarius)
is said to have a Declination of zero, shown
as 0° 0’ 0”.
All celestial objects therefore may be located
with their celestial coordinates of Right
Ascension and Declination.
LINING UP WITH THE CELESTIAL POLE
Objects in the sky appear to revolve around
the celestial pole. (Actually, celestial objects
are essentially “fixed” and their apparent
motion is caused by Earth’s rotation). During
any 24 hour period, stars make one complete
revolution about the pole, circling with the
pole at the center. By lining up the telescope’s
polar axis with the North Celestial Pole (or
for observers located in Earth’s Southern
Hemisphere with the South Celestial Pole),
astronomical objects may be followed, or
“tracked,” by moving the telescope about one
axis, the polar axis.
If the telescope is reasonably well aligned
with the pole very little use of the telescope’s
Declination flexible cable control is necessary.
Virtually all of the required telescope tracking
will be in Right Ascension. For the purposes of casual visual telescopic observations,
lining up the telescope’s polar axis to within
a degree or two of the pole is more than
sufficient: with this level of pointing accuracy,
the telescope can track accurately by slowly
turning the telescope’s R.A. flexible cable
control and keep objects in the telescopic
field of view for perhaps 20 to 30 minutes.
POLAR ALIGNMENT OF THE EQUATORIAL
MOUNT
To line up the Meade Polaris German
TOO MUCH POWER?
Can you ever have too much power? If the type of
power you’re referring to is eyepiece magnification,
yes you can! The most common mistake of the
beginning observer is to “overpower” a telescope
by using high magnifications which the telescope’s
aperture and atmospheric conditions cannot
reasonably support. Keep in mind that a smaller,
but bright and well-resolved image is far superior
to one that is larger, but dim and poorly resolved.
Powers above 400x should be employed only under
the steadiest atmospheric conditions.
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
Fig. 8
9
Little Dipper
Big Dipper
Polaris
Cassiopeia
Equatorial mount with the celestial pole,
follow this procedure:
1. Slightly loosen the Azimuth lock (30) of the
Azimuth base, so that the entire telescopewith-mounting may be rotated in a horizontal
direction. Rotate the telescope until it points
due North. Use a compass or locate Polaris,
the North Star, as an accurate reference to
North (See Fig. 8).
2. Level the mount with the horizon, if
necessary, by adjusting the heights of the
three tripod legs.
3. Determine the latitude of your observing
location by checking a road map or atlas.
Release the latitude lock (9) and tilt the
telescope mount so that the star “Polaris”
10
is centered in the telescope’s red
dot viewfinder. Then center it in the
MA25mm eyepiece. Next, re-tighten the
latitude lock.
4. If the above steps (1-3) were performed
with reasonable accuracy, your telescope
is now sufficiently well-aligned to the North
Celestial Pole for visual observations.
You will enjoy your telescope even more
as you learn more about it. But don’t be
scared off by difficult terms or complicated
procedures. Don’t panic! Just relax and enjoy
your scope.
Once the mount has been polar-aligned as
described above, the latitude angle need
not be adjusted again, unless you move to a
different geographical location (i.e. a different
latitude). The only polar alignment procedure
that you need to perform each time you use
the telescope is to point the polar axis due
North, as described in step 1 above.
You will begin to grow and learn more about
astronomy the more you observe. Go on
the internet or to the library and read some
books about the stars and planets. Read
about astronomers of old. Many of them
had telescope no bigger than the one you
are using right now. Galileo, who is one of
the first astronomers to use a telescope,
discovered four of the moons of Jupiter with a
telescope about the same size as yours (and
his didn’t even focus very well!).
THE MOST IMPORTANT RULE
OBSERVING
We have one very important rule that you
should always follow when using your
telescope: Have Fun!
Have a good time when you’re observing.
You may not know everything that there is to
know about a telescope or what all the sights
in the universe are, but that’s OK. Just point
and observe at first.
Observe during the daytime: Try out your
telescope during the daytime at first. It is
easier to learn how it operates and how to
observe when it is light.
Pick out an easy object to observe: A
distant mountain, a large tree, a lighthouse
or skyscraper make excellent targets. Point
the optical tube so it lines up with your object.
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
In Reflecting telescope models, objects will
appear upside down and backwards in this
model telescope due to the position of the
eyepiece.
Unlock the lock knobs:
To move the
telescope, you will need to unlock the Right
Ascension (22, Fig. 3) and Declination (23,
Fig. 3) lock knobs (just rotate to unlock or
lock; when locking, only tighten to a “firm
feel,” do not over tighten).
Use the red dot viewfinder: If you have
not done so, align the viewfinder (24) with
the telescope’s eyepiece (19) as described
earlier. Look through the red dot viewfinder
until you can see the object. It will be easier to
locate an object using the red dot viewfinder
rather than locating with the eyepiece. Line
up the object using the viewfinders red dot.
move the telescope. These can come in very
handy, especially when you wish to move the
telescope in very small (fine control) steps.
Look through the eyepiece: Once you have
the object lined up in the viewfinder, look
through the optical tube’s eyepiece. If you
have aligned your viewfinder, you will you see
the object in your eyepiece.
Observe the Moon: When you feel comfortable
with the viewfinder, the eyepieces, the locks
and the adjustment controls, you will be ready
to try out the telescope at night. The Moon
is the best object to observe the first time
you go out at night. Pick a night when the
Moon is a crescent. No shadows are seen
during a full Moon, making it appear flat and
uninteresting.
Focus: Look through the eyepiece and
practice focusing on the object you have
chosen.
Try out the slow-motion flexible cable control:
Practice using the right ascension control
cable (3) and declination control cable (4) to
Look for different features on the Moon. The
most obvious features are craters. In fact
you can see craters within craters. Some
craters have bright lines about them. These
are called rays and are the result of material
thrown out of the crater when it was struck
by a colliding object. The dark areas on the
Moon are called maria and are composed of
lava from the period when the Moon still had
volcanic activity. You can also see mountain
ranges and fault lines on the Moon.
Use a neutral density filter (often called a
“moon filter”) when observing the Moon.
Neutral density filters are available from
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
Fig. 9
11
Meade as an optional accessory and enhance
contrast to improve your observation of lunar
features.
Spend several nights observing the Moon.
Some nights, the Moon is so bright that it
makes other objects in the sky difficult to see.
These are nights that are excellent for lunar
observation.
Observe the Solar System: After observing
the Moon, you are ready to step up to the
next level of observation, the planets. There are four planets that you can easily
observe in your telescope: Venus, Mars,
Jupiter and Saturn.
Nine planets (maybe more!) travel in a fairly
circular pattern around our Sun. Any
system of planets orbiting one or more
12 stars is called a solar system. Our Sun,
by the way, is a single, yellow dwarf
star. It is average as far as stars go and is a
middle aged star.
Beyond the planets are clouds of comets, icy
planetoids and other debris left over from the
birth of our sun. Recently astronomers have
found large objects in this area and they may
increase the number of planets in our solar
system.
The four planets closest to the Sun are rocky
and are called the inner planets. Mercury,
Venus, Earth and Mars comprise the inner
planets. Venus and Mars can be easily seen
in your telescope.
Venus is seen before dawn or after sunset,
because it is close to the Sun. You can
observe Venus going through crescent
phases. But you cannot see any surface
detail on Venus because it has a very thick
atmosphere of gas.
When Mars is close to the Earth, you can
see some details on Mars, and sometimes
even Mars’ polar caps. But quite often, Mars
is further away and just appears as a red dot
with some dark lines crisscrossing it.
the positions of the moons each night is an
excellent exercise for novice astronomers.
Jupiter, Saturn, Uranus, Neptune and Pluto
comprise the outer planets. These planets,
except for Pluto, are made mostly of gases
and are sometimes called gas giants. If they
had grown much bigger, they may have
become stars. Pluto is made mostly of ice.
Any small telescope can see the four
Galilean moons of Jupiter (Fig. 9), plus a few
others, but how many moons does Jupiter
actually have? No one knows for sure! Nor
are we sure how many Saturn has either. At
last count, Jupiter had over 60 moons, and
held a small lead over Saturn. Most of these
moons are very small and can only be seen
with very large telescopes.
Jupiter is quite interesting to observe. You
can see bands across the face of Jupiter. The
more time you spend observing these bands,
the more details you will be able to see.
One of the most fascinating sights of Jupiter
are its moons. The four largest moons
are called the Galilean moons, after the
astronomer Galileo, who observed them for
the first time. If you’ve never watched the
Galilean moons in your telescope before,
you’re missing a real treat! Each night, the
moons appear in different positions around
the Jovian sky. This is sometimes called
the Galilean dance. On any given night,
you might be able to see the shadow of a
moon on the face of Jupiter, see one moon
eclipse another or even see a moon emerge
from behind Jupiter’s giant disk. Drawing
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
Probably the most memorable sight you will
see in your telescope is Saturn. Although
SURF THE WEB
• The Meade 4M Community:
http://www.meade4m.com
• Sky & Telescope:
http://www.skyandtelescope.com
•Astronomy:
http://www.astronomy.com
• Astronomy Picture of the Day:
http://antwrp.gsfc.nasa.goc/apod
• Photographic Atlas of the Moon:
http://www.lpi.ursa.edu/research/lunar_orbiter
• Hubble Space Telescope Public Pictures:
http://oposite.stsci.edu/pubinfo/pictures.html
you may not see many features on the
surface of Saturn, its ring structure will steal
your breath away. You will probably be able
to see a black opening in the rings, known as
the Cassini band.
Saturn is not the only planet that has rings,
but it is the only set of rings that can be seen
with a small telescope. Jupiter’s rings cannot
be seen from Earth at all—the Voyager
spacecraft discovered the ring after it passed
Jupiter and looked back at it. It turns out, only
with the sunlight shining through them, can
the rings be seen. Uranus and Neptune also
have faint rings.
Optional color filters help bring out detail and
contrast of the planets. Meade offers a line of
inexpensive color filters.
What’s Next? Beyond the Solar System:
Once you have observed our own system of
planets, it’s time to really travel far from home
and look at stars and other objects.
You can observe thousands of stars with
your telescope. At first, you may think stars
are just pinpoints of light and aren’t very
interesting. But look again. There is much
information that is revealed in stars.
The first thing you will notice is that not all
stars are the same colors. See if you can find
blue, orange, yellow, white and red stars. The
color of stars sometimes can tell you about
the age of a star and the temperature that
they burn at.
Other stars to look for are multiple stars.
Very often, you can find double (or binary)
stars, stars that are very close together.
These stars orbit each other. What do you
notice about these stars? Are they different
colors? Does one seem brighter than the other?
Almost all the stars you can see in the
sky are part of our galaxy. A galaxy is a
large grouping of stars, containing millions
or even billions of stars. Some galaxies form
a spiral (like our galaxy, the Milky Way) and
other galaxies look more like a large football
and are called elliptical galaxies. There are
many galaxies that are irregularly shaped
and are thought to have been pulled apart
because they passed too close to—or even
through—a larger galaxy.
You may be able to see the Andromeda
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
galaxy and several others in your
telescope. They will appear as small,
fuzzy clouds. Only very large telescope
will reveal spiral or elliptical details.
13
You will also be able to see some nebulas
with your scope. Nebula means cloud. Most
nebulas are clouds of gas. The two easiest
to see in the Northern Hemisphere are the
Orion nebula during the winter and the Triffid
nebula during the summer. These are large
clouds of gas in which new stars are being
born. Some nebulas are the remains of
stars exploding. These explosions are called
supernovas.
Fig. 10
eyepiece
barlow
When you become an advanced
observer you can look for other
14 types of objects such as asteroids,
planetary nebula and globular clusters.
And if you’re lucky, every so often a bright
comet appears in the sky, presenting an
unforgettable sight.
The more you learn about objects in the
sky, the more you will learn to appreciate
the sights you see in your telescope. Start
a notebook and write down the observations
you make each night. Note the time and the
date.
Use a compass to make a circle, or trace
around the lid of a jar. Draw what you see
in your eyepiece inside the circle. The best
exercise for drawing is to observe the moons
of Jupiter every night or so. Try to make
Jupiter and the moons approximately the
same size as they look in your eyepiece.
You will see that the moons are in a different
position every night. As you get better at
drawing, try more challenging sights, like a
crater system on the moon or even a nebula.
Go your library or check out the internet for
more information about astronomy. Learn
about the basics: light years, orbits, star
colors, how stars and planets are formed,
red shift, the big bang, what are the different
kinds of nebula, what are comets, asteroids
and meteors and what is a black hole. The
more you learn about astronomy, the more
fun, and the more rewarding your telescope
will become.
SOME OBSERVING TIPS
Eyepieces: Always begin your observations
using the 25mm low-power eyepiece. The
25mm eyepiece delivers a bright, wide field
of view and is the best to use for most
viewing conditions. Use the high-power 9mm
eyepiece to view details when observing
the Moon and planets. If the image become
fuzzy, switch back down to a lower power.
Changing eyepieces changes the power or
magnification of your telescope.
By the way, users of reflecting telescopes
may have noticed something strange when
looking through your eyepiece. The image
is upside down and reversed. That means
reading words can be a problem. But it has
no affect on astronomical objects.
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
Optional Accessory Barlow lens: You can
also change magnification by using a Barlow
lens. The Barlow lens doubles the power of
your telescope (See Fig. 10).
Meade offers a complete line of eyepieces for
your telescope. Most astronomers have four
or five low-power and high power eyepieces
to view different objects and to cope with
different viewing conditions.
Objects move in the eyepiece: If you are
observing an astronomical object (the
Moon, a planet, star, etc.) you will notice
that the object will begin to move slowly
through the telescopic field of view. This
STAR CHARTS
Star charts and planispheres are useful for a variety of
reasons. In particular, they are a great aid in planning a
night of celestial viewing.
A wide variety of star charts are available in books,
in magazines, on the internet and on CD Roms.
Meade offers AutoStar SuiteTM software. Contact your
local Meade dealer or Meade’s Customer Service
department for more information.
Astronomy and Sky and Telescope magazines print
star charts each month for up-to-the-minute maps of
the heavens.
movement is caused by the rotation of the
Earth and makes an object move through
the telescope’s field of view. To keep
astronomical objects centered in the field,
simply move the telescope on one or both
of its axes—vertically and/or horizontally as
needed—try using the telescopes coarse and
fine adjustment controls. At higher powers,
astronomical objects will seem to move
through the field of view of the eyepiece
more rapidly.
that the object to be viewed is again placed
at the edge of the field, ready to be further
observed.
Place the object to be viewed at the edge of
the field and, without touching the telescope,
watch it drift through the field to the other
side before repositioning the telescope so
Let your eyes “dark-adapt:” Allow five or
ten minutes for your eyes to become “dark
adapted” before observing. Use a redfiltered flashlight to protect your night vision
when reading star maps, or inspecting the
telescope. Stay away from bright lights too.
Do not use a regular flash-light or turn on
other lights when observing with a group of
other astronomers. You can make your own
red filtered flashlight by taping red cellophane
over a flashlight lens.
Vibrations: Avoid touching the eyepiece while
observing through the telescope. Vibrations
resulting from such contact will cause the
image to move. Avoid observing sites where
vibrations cause image movement (for
example, near railroad tracks). Viewing from
the upper floors of a building may also cause
image movement.
Viewing through windows: Avoid setting up
the telescope inside a room and observing
through an opened or closed window pane.
Images may appear blurred or distorted
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
due to temperature differences between
inside and outside air. Also, it is a
good idea to allow your telescope to 15
reach the ambient (surrounding) outside
temperature before starting an observing
session.
When to observe: Planets and other objects
viewed low on the horizon often lack sharpness—the same object, when observed
higher in the sky, will appear sharper and
have greater contrast. Try reducing power
(change your eyepiece) if your image is fuzzy
or shimmers. Keep in mind that a bright,
clear, but smaller image is more interesting
than a larger, dimmer, fuzzy one. Using too
JOIN AN ASTRONOMY CLUB, ATTEND A STAR
PARTY
One of the best ways to increase your knowledge of
astronomy is to join an astronomy club. Check your
local newspaper, school, library, or telescope dealer/
store to find out if there’s a club in your area.
Many groups also hold regularly scheduled Star Parties
at which you can check out and observe with many
different telescopes and other pieces of astronomical
equipment. Magazines such as Sky and Telescope
and Astronomy print schedules for many popular Star
Parties around the United States and Canada.
16
high a power eyepiece is one of the
most common mistakes made by new
astronomers.
Dress Warm: Even on summer nights,
the air can feel cool or cold as the night wears
on. It is important to dress warm or to have a
sweater, jacket, gloves, etc., nearby.
Know your observing site: If possible, know
the location where you will be observing. Pay
attention to holes in the ground and other
obstacles. Is it a location where wild animals,
such as skunks, snakes, etc., may appear?
Are there viewing obstructions such as tall
trees, street lights, headlights and so forth?
ASTRONOMY RESOURCES
•
•
•
•
•
The Meade 4M Community
27 Hubble, Irvine, CA 92618
Astronomical League
Executive Secretary
5675 Real del Norte, Las Cruces, NM 88012
The Astronomical Society of the Pacific
390 Ashton Ave., San Francisco, CA 94112
The Planetary Society
65 North Catalina Ave, Pasadena, CA 91106
International Dark-Sky Association, Inc.
3225 N. First Avenue, Tucson, AZ 85719-2103
The best locations are dark locations, the
darker the better. Deep space objects are
easiest to see under dark skies. But it is still
possible to observe even in a city.
POLARIS 80
Surf the Web and visit your local library:
The internet contains a huge amount of
astronomical information, both for children
and adults. Check out astronomy books from
your library. Look for star charts—these are
available on a monthly basis in Astronomy
and Sky and Telescope magazines.
Objective lens diameter...........…80mm (3.1”)
HAVE A GOOD TIME,
ASTRONOMY IS FUN!
SPECIFICATIONS
POLARIS 70
Optical tube design………..............Refractor
Optical tube focal length…................900mm
Objective lens diameter…...........70mm (2.8”)
Focal ratio……………....................….....f/12.9
Mount…………........Small German Equatorial
Optical tube design………................Refractor
Optical tube focal length.....................900mm
Focal ratio…………….....................……f/11.3
Mount…………....…Small German Equatorial
POLARIS 90
Optical tube design…................…...Refractor
Optical tube focal length.....................900mm
Objective lens diameter...............90mm (3.5”)
Focal ratio……………..........................….f/10
Mount………......…..Large German Equatorial
POLARIS 114
Optical tube design……...............….Reflector
Optical tube focal length…..................900mm
Primary mirror diameter.............114mm (4.5”)
Focal ratio……….......................…………f/7.9
Mount………....……Large German Equatorial
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
POLARIS 127
Optical tube design……..................….Reflector
Optical tube focal length…..................1000mm
Primary mirror diameter…............127mm (5.0”)
Focal ratio…………...................…….....….f/7.9
Mount…….............…Large German Equatorial
POLARIS 130
Optical tube design……..................….Reflector
Optical tube focal length..........................650mm
Primary mirror diameter…..............130mm (5.1”)
Focal ratio…………….............................…….f/5
Mount…………........…Large German Equatorial
What do the specifications mean?
Optical tube focal length is simply a measurement
of the length of the optical tube. In other words,
this is the distance light travels in the telescope
before being brought to focus in you eyepiece.
For example, the Polaris 90 Refractor tube is
900mm long.
how fast the photographic speed
of a telescope is. The lower the
focal ratio number, the faster the 17
exposure. F/5 is faster than f/10.
Monture
The slower the focal ratio, the longer
Miroir Diagonal
Miroir Primaire
Diagonale
the exposure time is needed when a
camera is hooked up to the telescope.
Vis D'inclinaison
For example, the Polaris 90 Refractor
du Miroir Primaire
Image Focalisée
has slow focal ratio at f/10. Sometimes,
astronomers use focal reducers to
The Newtonian Reflecting Telescope
make slow exposure telescopes have
faster focal ratios.
Primary mirror diameter (reflectors) or
Objective lens diameter (refractors) is how
big the mirror or lens is on your scope.
USE
THE
SPECIFICATIONS
Telescopes are always described by how
TO
CALCULATE
THE
Fig. 12
large their primary mirror/lens is.
MAGNIFICATION OF YOUR
For example, the objective lens
EYEPIECE
on the Polaris 90 is 90mm or
The power of a telescope is how
3.5 inches. Telescopes come in
much it magnifies objects. Each
many different sizes. They can
telescope has its own set of focal
be 70mm, 8 inches, 16 inches,
1
lengths
and, therefore, different
or even 3 feet in diameter. The
magnifications when used with
2
Hubble Space Telescope’s
various eyepieces. For example,
primary mirror has a diameter
the Polaris 90 used 3with the 25mm
of 2.4 meters (that’s 7.8 feet
eyepiece magnifies an object 36
across!).
Secondary Mirror Assembly
times. The 9mm eyepiece used
The focal ratio helps determine
with the Polaris 90 will magnify
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
Fig. 11
objects 100 times.
You can calculate how much
magnification an eyepiece will have with
your specific telescope. Just divide the
telescope focal length by the focal length of
the eyepiece.
18
Focal Length of the Telescope
÷
Focal Length of the Eyepiece
=
Magnification
Look at the specifications. For example, you
will see that the focal length of the Polaris 90
is 900mm. Let’s say that you have obtained a
6.3mm eyepiece. You can tell what the focal
length of your eyepiece is as it is always
printed on the side of the eyepiece. Divide:
900mm ÷ 6.3mm, which equals 142.86.
Round this off to the nearest whole number
and you find the 6.3mm eyepiece used with
the Polaris 90 magnifies objects 143 times.
If you use a Barlow lens with one of your
eyepieces, it doubles the magnification of
your eyepiece. Other types of Barlows
can triple or further increase the power of
an eyepiece. To find out how much your
magnification is when you use a 2x Barlow,
multiply your eyepiece’s magnification by two.
For example, the 25mm low-power eyepiece
used with the Polaris 90 magnifies an object
36 times. Multiply 36 by 2 and you get 72
times magnification with a Barlow.
Eyepiece’s magnification x 2
=
Magnification with a 2X Barlow lens
It’s worth repeating: Keep in mind that a
bright, clear, but smaller image is more
interesting than a larger, dimmer, fuzzy one.
Using too high a power eyepiece is one
of the most common mistakes made by
new astronomers. So don’t think that higher
magnification is necessarily better—quite
often the best view is with lower magnification
value!
TAKING CARE OF YOUR TELESCOPE
Your telescope is a precision optical instrument
designed for a lifetime of rewarding viewing.
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
It will rarely, if ever, require factory servicing
or maintenance. Follow these guidelines to
keep your telescope in the best condition:
•As with any quality instrument, lens or mirror
surfaces should be cleaned as infrequently
as possible. Front surface aluminized mirrors
(reflecting models), in particular, should be
cleaned only when absolutely necessary. In
all cases avoid touching any mirror surface.
A little dust on the surface of a mirror or lens
causes negligible loss of performance and should not be considered reason to clean
the surface. When lens or mirror cleaning
does become necessary, use a camel’s hair
brush or compressed air gently to remove
dust. If the telescope’s dust cover is replaced
after each observing session, cleaning of the
optics will rarely be required.
•Fingerprints and organic materials on
the lens or mirror may be removed with a
solution of 3 parts distilled water to 1 part
isopropyl alcohol. You may also add 1 drop
of biodegradable dishwashing soap per pint
of solution. Use soft, white facial tissues and
make short, gentle strokes. Change tissues
often.
CAUTION: Do not use scented or lotioned
Fig. 13
3
Fig. 14
2
2
3
3
2
4
4
5
5
Correct Collimation
1
1
1
1
2
2
2
Fig. 15
3
2
2
2
3 Mirror Misalignment
Secondary
4
2
5
1
Primary Mirror Cell
tissues or damage could result to the optics.
DO NOT use a commercial photographic lens cleaner.
2
4
3
4
4
COLLIMATION (ALIGNMENT) OF OPTICS
(REFLECTING MODELS ONLY)
All Meade Polaris Reflecting telescopes
are optically aligned at the factory prior to
shipment. It is unlikely that you will need to
align, or collimate, the optics after receipt
of the instrument. However, if the telescope
received unusually rough handling in
1
2
3
19
3
1
1
you will recognize a properly collimated
instrument and can adjust the collimation
yourself, if necessary.
Fig. 16
1
2
A. CORRECT
COLLIMATION
3
The properly collimated (aligned) mirror
system in the Meade Polaris telescope
assures the sharpest images possible. This
occurs when the primary mirror and secondary
mirror are tilted so that the focused image
falls directly through the center of the focuser
draw tube. These mirror tilt adjustments are
made with the secondary mirror assembly
and the primary mirror cell (Fig. 13) and will
be discussed later.
3
Fig. 17
Primary Mirror Misalignment
shipment, it is possible that the optics must
be re aligned for best optical performance.
In any case this alignment procedure is
simple, and requires only a few minutes
the very first time the telescope is used.
Take the time to familiarize yourself with
the following collimation procedure, so that
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
A
Collimation
B
C
To inspect the view of the mirror
collimation, look down the focuser draw
20 tube with the eyepiece removed. The
edge of the focuser drawtube (1, Fig.
14), will frame the reflections of the
primary mirror with the 3 mirror clips (2,
Fig. 14), the secondary mirror (3, Fig. 14),
the spider vanes (4, Fig. 14), and your
eye (5, Fig. 14). Properly aligned, all of
these reflections will appear concentric (i.e.,
centered) as illustrated in Fig. 14.
Any deviation from the concentric reflections
will require adjustments to the secondary
mirror assembly and/or the primary mirror
cell (Fig. 12).
B. SECONDARY
ADJUSTMENTS
MIRROR
HOLDER
If the secondary mirror (1, Fig. 15) is centered
in the draw tube (2, Fig. 15), but the primary
mirror is only partially visible in the reflection
(3, Fig. 15), one or more of the 3 Phillipshead secondary mirror collimation screws
need adjusting. First, unthread each of
the secondary mirror collimation screws
slightly to the point of where you can tilt
the secondary holder from side-to-side. By
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
grasping the secondary holder with your
hand, tilt the secondary mirror holder until you
see the primary mirror become as centered
in the reflection of the diagonal mirror as
possible. Once you are at the best position,
thread in the 3 Phillips-head secondary mirror
collimation screws to lock the holder in place.
Then, if necessary, make adjustments to
these 3 Phillips-head screws to refine the tiltangle of the secondary mirror until the entire
primary mirror can be seen centered within
the secondary mirror reflection. When the
secondary mirror is correctly aligned, it will
look like Fig. 16 (Note: The primary mirror is
shown out of alignment).
C. PRIMARY MIRROR ADJUSTMENTS
If the secondary mirror (1, Fig. 16) and the
reflection of the primary mirror (2, Fig. 16)
appear centered within the draw tube (3, Fig.
16), but the reflection of your eye and the
reflection of the secondary mirror (4, Fig. 16)
appear off center, you will need to adjust the
primary mirror tilt screws of the primary mirror
cell (2, Fig. 13). These primary tilt screws
are located behind the primary mirror, at the
lower end of the main tube.
To adjust the primary mirror tilt screws (2, Fig
13), first turn by several turns, the primary
mirror cell lock knobs (3, Fig. 13) that are next
to each primary mirror tilt screw. The three
primary mirror cell locking screws are Phillips
head screws on all Polaris models.
Then by trial-and-error, turn the primary mirror
tilt knobs (2, Fig. 13) until you develop a feel
for which way to turn each knob to center the
reflection of your eye. Once centered, as in
Fig. 14, turn the 3 primary mirror cell locking
screws (3, Fig. 13) to re-lock the tilt-angle
adjustment.
NOTE: Some models have large thumb knobs
for the primary mirror cell tilt knobs(2, Fig 13).
Other models have Phillips head screws as
the primary mirror cell tilt screws. On these
models, the primary mirror cell tilt screws (2,
Fig 13) are the screws that have the screw
heads touching the rear cell.
D. STAR TESTING THE COLLIMATION
With the collimation performed, you will want
to test the accuracy of the alignment on a
star. Use the 25mm eyepiece and point the
telescope at a moderately bright (second or
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
third magnitude) star, then center the
star image in the telescope’s field-ofview. With the star centered follow the
method below:
21
• Bring the star image slowly out of focus
until one or more rings are visible around the
central disc. If the collimation was performed
correctly, the central star disk and rings will
be concentric circles, with a dark spot dead
center within the out-of-focus star disk (this
is the shadow of the secondary mirror), as
shown in Fig. 17C. (An improperly aligned
telescope will reveal elongated circles (Fig.
17A), with an off-center dark shadow.)
•If the out-of-focus star disk appears
elongated (Fig. 17A), you will need to adjust
the primary mirror adjusting tilt screws of the
primary mirror cell (3, Fig. 13)
•To adjust the primary mirror tilt screws (3,
Fig. 13), first unscrew several turns the 3
hex-head primary mirror cell locking screws
(2, Fig. 13), to allow free turning movement
of the tilt knobs.
•Using the flexible cable controls move the
telescope until the star image is at the edge
of the field-of-view in the eyepiece, as in Fig.
17B.
•As you make adjustments to the
22 primary mirror tilt screws (3, Fig. 13),
you will notice that the out-of-focus star
disk image will move across the eyepiece
field. Choose one of the 3 primary mirror tilt
screws and slightly move the shadow to the
center of the disk. Then slightly move the
telescope using the flexible cable controls to
center the star disk image in the center of the
eyepiece.
• If any further adjustments are necessary,
repeat this process as many times as needed
until the out-of-focus star disk appears as in
Fig. 18C, when the star disk image is in the
center of the eyepiece field.
• With the star testing of the collimation
complete, tighten the 3 hex-head primary
mirror locking screws (2, Fig. 13)
push here to open
battery compartment
Fig. 18
CR2032
battery
battery
compartment
To replace the battery, press the left side
of the viewfinder housing labeled “push”.
The battery compartment will slide out on
the right side of the viewfinder (see Fig.
18). Replace the battery with a Lithium
CR2032 battery with the positive side up.
Then push the battery compartment back
into the viewfinder and power on.
CHANGING THE VIEWFINDER BATTERY
If the viewfinder red dot does not illuminate, verify the viewfinder is on by rotating
the knob below the viewfinder lens clockwise. If the red dot does not illuminate, the
battery may need replacing.
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
OPTIONAL ACCESSORIES
Additional
Eyepieces
(1.25”
barrel
diameter only): For higher or lower viewing
magnifications, Meade’s Series 4000 Super
Plössl eyepieces, available in a wide variety of
sizes, provide a high level of image resolution
and color correction at an economical price.
Contact your Meade Dealer or see the Meade
catalog for more information. Visit us on the
web at www.meade.com.
MEADE CONSUMER SOLUTIONS
If you have a question concerning your
telescope, call Meade Instruments Consumer
Solutions Department at (800) 626-3233.
Consumer Solutions Department hours are
7:00AM to 5:00PM, Pacific Time, Monday
through Friday. Call the Meade Consumer
Solutions Department first, before returning
the telescope to the factory, giving full
particulars as to the nature of the problem,
as well as your name, address, and daytime
telephone number. The great majority of
servicing issues can be resolved by telephone,
avoiding return of the telescope to the factory.
MEADE LIMITED WARRANTY
Every Meade telescope, and telescope
accessory is warranted by Meade Instruments
Corp. (“Meade”) to be free of defects in
materials and workmanship for a period
of ONE YEAR from the date of original
purchase in the U.S.A. Meade will repair or
replace a product, or part thereof, found by
Meade to be defective, provided the defective
part is returned to Meade, freight-prepaid,
with proof of purchase. This warranty applies
to the original purchaser only and is non-
transferable. Meade products purchased
outside North America are not included in
this warranty, but are covered under separate
warranties issued by Meade international
distributors.
RGA Number Required: Prior to the
return of any product or part, a Return
Goods Authorization (RGA) number must
be obtained from Meade by writing, or by
calling (800) 626-3233. Each returned part
or product must include a written statement
detailing the nature of the claimed defect,
as well as the owner’s name, address, and
phone number.
This warranty is not valid in cases where the
product has been abused or mishandled,
where unauthorized repairs have been
attempted or performed, or where depreciation
of the product is due to normal wear-and-tear.
Meade specifically disclaims special, indirect,
or consequential damages or lost profit which
may result from a breach of this warranty.
Any implied warranties which cannot be
disclaimed are hereby limited to a term of one
year from the date of original retail purchase.
This warranty gives you specific rights. You
Looking at or near the Sun will cause irreversable damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
may have other rights which vary from
state to state.
Meade reserves the right to change
product specifications or to discontinue
products without notice.
23
This warranty supersedes all previous Meade
product warranties.
©2014 MEADE INSTRUMENTS CORP.
OBSERVATION LOG
OBSERVER:
OBJECT NAME:
DATE & TIME OBSERVED:
CONSTELLATION:
EYEPIECE SIZE:
SEEING CONDITIONS:
EXCELLENT
GOOD
POOR
NOTES:
DRAWING OF IMAGE
OBSERVATION LOG
OBSERVER:
OBJECT NAME:
DATE & TIME OBSERVED:
CONSTELLATION:
EYEPIECE SIZE:
SEEING CONDITIONS:
EXCELLENT
GOOD
POOR
NOTES:
DRAWING OF IMAGE
www.meade.com
626-3233
1-800
Meade Instruments Corp.
27 Hubble, Irvine,
California
92618