SECTION 06403
PART 1
-
-
CASEWORK
GENERAL
1.01 RELATED WORK
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 specification sections, apply to work of this section.
B.
Section 1541 1
"Plumbing F ~ t u r e sand Trim"
C.
Section 01030
"Alternates"
1.02 APPLICABLE WORK
A. This Section includes the following:
1. Quartz surfacing countertops
2. Solid Surface Material Countertops and Sinks (alternate bid)
3. Stainless steel covered panels
4. Stainless steel countertops
5. Laminate covered panels (alternate bids)
6. Laminate covered cabinets
7. Wood valances
8. Other Casework indicated on the drawings
Submit the following in accordance with Cornlitions of Contract and Division
A. General:
1 Specification Sections.
Shop drawings showing location of each item, dimensioned plans and elevations. largescale details, attachment devices, and other components.
B.
C. Samples to venfy quartz surfacing finishes, plastic laminate selections, and solid surface
materials.
1.04 QUALITY ASSURANCE
A Manufacturer Qualifications: Firm experienced in successfully producing wood cabinets
similar to that indicated for this Project
B. Single-Source Manufacturing and Installation Responsibility: Engage a qualified Manufacturer
to assume undivided responsibility for the work specified in this section, including fabrication.
finishing, and installation.
C. AWI Certificatjon: Engage a fabricator who is certified by the countertop material
manufacturer.
1.05 DELIVERY. STORAGE. AND HANDLING
A Protect materials during transit, deliiety, storage, and handling to prevent damage.
CENTURY CENTER
RESTROOM REMODEL
-
CASEWORK 06403 1
B. Do not deliver casework until painting, wet work, grinding, and similar operations that
could damage, soil, or deteriorate casework have been completed in installation areas. If
woodwork must be stored in other than installation areas, store only in areas whose
environmental conditions meet requirements of the manufacturer.
1.06 PROJECT CONDmONS
A Field Measurements: Where woodwork is indicated t o be fitted to other construction,
check actual dimensions of other construction by accurate field measurements before
manufacturing woodwork.
6. Coordination:
PART 2
-
Coordinate countertops with sinks and accessories.
PRODUCTS
2.01 QUARTZ SURFACING COUNTERTOPS
A Provide the following product Zodiaqm quartz surfaces from DuPont
B. Thickness: For horizontal surfaces and elsewhere a s shown on the drawings: 1-1/8"
For vertical shelf support and end closures: contractor's option
C. Edge treatments:
Men's Areas: Single ovolo
Women's Areas: Imperial edge
D. Colors: See schedule at the end of this Section.
E Seam width cl/8"
F. Sink mounting:
G. Backsplash:
Under-mount
See drawings
H. Sink/bowl mounting hardware: Use Manufacturer's approved bowl clips, brass inserts and
fasteners for attachment of under-mount sinks/bowls.
I. Joint adhesive: Manufacturer-approved adhesive to create color-matched seam.
J. Warranty:
Provide manufacturer's 10-year warranty against defects in materials.
2.02 SOUD SURFACE COUNTERTOPS & SINKS
A Provide the following product
(ALTERNATE BID)
Corian solid surface by DuPont
B. Thickness: For horizontal surfaces and elsewhere a s shown on the drawings: Lz" thick.
Adjust dimensions of countertop supports a s required.
C. Edge .treatment 1" to 1-1/4" thickened edge w/ radius
D.
Colors:
see schedule at the end of this section
E Sinks. Under alternate bid. provide integral Corian sinks in Corian countertops in lieu of
Sinks to be under-mounted t o the
under-mounted porcelain sinks in quartz surfacing tops.
tops and be seamed flush with the face of the solid surface countertop.
CENTURY CENTER
RESTROOM REMODEL
CASEWORK 06403 - 2
F. Sinks: Color: Bone. Sink Style
G. Backsplash:
=
$810
See drawings
H. Joint adhesive: Manufacturer-approved adhesive to create invisible seam.
I. Solid substrate: MDF board or other manufacturer approved material
J. Warranty:
Provide manufacturer's IO-year warranty against defects in materials.
2.03 HIGH PRESSURE DECORATIVE lAMlNATE
A
Manufacturer:
Subject to compliance with requirements,
decorative laminates of one of the following:
1. Formica Corp.
2. Laminah
3. Nevamar Corp.
provide
high
pressure
4. Pionite
5. Ralph W~lsonPlastics co.
B. Colors: To be selected by Architect from any of the manufacturer's standard colors.
C. General:
standards:
Provide materials that comply with requirements of the referenced product
1. High Pressure Laminate: NEMA LD 3.
2. Particleboard: ANSI ,4208.1
3. Plywood:
2.04 FABRICATION. GENERAL
A Drawings indicate general design intent, including most materials and details. The
drawings are not meant to show every condition. Fabricator is to provide complete and
finished cabinet work, reinforced and finished to perform its intended function.
B. Complete fabrication, including assembly, finishing. and hardware application, before
shipment to project site to maximum extent possible. Disassemble components only
as necessary for shipment and installation.
Where necessary for W n g at site,
provide ample allowance for scribing, trimming, and fitting.
C. Factory-cut openings, to maximum extent possible. to receive hardware. plumbing
fixtures, electrical work, and similar items. Locate openings accurately and use templates
or roughing-in diagrams to produce accurately sized and shaped openings. Smooth edges
of cutouts and, where located in countertops and similar exposures, seal edges of cutouts
with a water-resistant coating.
2.05 LAWllNATE
COVERED WOOD CABINETS
A Wood cabinets in office/retail areas rooms to have minimum construction and finish
requirements as follows. If not listed, follow the requirements of AWI Premium grade
laminate covered cabinets:
1.
Door Construction: 3/4" particleboard w/ HP laminate on edges and outside face.
Hinges to be continuous off-set hinges with mechanical or magnetic keeper and
CENTURY CENTER
RESTROOM REMODEL
CASEWORK 06403 - 3
lock. Provide US 10B wire-type pull for each door.
construction.
Doors to be full overlay
2. Cabinet Construction:
a. face frames - 3/4" laminate covered particle board
b. shelves - H.P. laminate covered 3/4" thk. particle board.
One 3/4 depth bottom shelf typical in lower cabinets (except recycling/waste
cabs.). Support shelves from adj. standards; thicken back edge of shelf or
provide additional standards as span requires.
c. interior sides, back, top, H.P. laminate or melamine covered particle board.
3. Provide laminate covered braces, cleats, and misc. supports as required.
4. Provide special wood trim and edging where shown in the drawings.
5. Provide locks on all lower cabinet doors.
A. Q u a l i Standard: Comply with applicable WIC Section 16
Countertops, Splashes and Wall Paneling".
-
"Laminated
Plastic
6.
Laminate Cladding for Countertops: Laminate colors to be selected by Architect
from manufacturer's standard colors. Grade: GP-50 (0.050-inch nominal thickness).
C. Edge Treatment and Splashes:
follows:
Same as laminate cladding on horizontal surfaces and as
1. Countertop Edge: As shown, if not shown: self-edge.
2. Backsplash: 4" high unless otherwise noted, applied or cove w/ self-edge or rolled
top. Calk with silicone as required at wall/countertop, splash/counter- top
intersections.
D. Seal underside/backside of countertops and backsplashes with water resistant paper or
sealer to limit moisture absorption of particle board substrate.
E Provide laminate covered braces, cleats, and metal supports as indicated or where
required.
2.07 STAINLESS SmL COVERED VANITY PANEL
A Provide tz" thick plywood panels with 18 gauge stainless steel with welded comers
laminated to the plywood on front and four edges. Provide z clips or other means of
securing the panels .to the support brackets so that they are readily removable, and remain
in alignment when re-attached. Provide with # 4 brushed finish.
A Provide 18 gauge # 4 stainless steel over %" Plywood or MDF board. Countertop to be
seamless. welded and ground smooth. Provide stainless steel backsplash. Support
countertop on existing supports for existing countertop to be removed.
CENTURY CENTER
RESTROOM REMODEL
CASEWORK 06403 - 4
2.09 WOOD VALANCE
A Provide edge-banded sanded birch plywood. Attach to wood supports with Z clips or
other type of connection that allows the valance to be removed for servicing of the cove
lights.
PART 3
-
EXECUTION
3.01 INSTALLATION
A. lnstall cabinets and tops plumb, level, true, and straight with no distortions. Shim as
required with concealed shims.
Install to a tolerance of 1/8 inch in 8'4" for plumb
and level (including tops) and with no more than 1/8" variation in flushness of adjoining
surfaces.
B. Install Cabinets: Install without distortion so that doors and drawers fit openings
properly and are accurately aligned. Adjust hardware to center doors and drawers in
openings and to provide unencumbered operation. Complete the installation of hardware
and accessory items as indicated.
C. Tops: Anchor securely to base units and other support systems as indicated. Scribe
and cut as required to fit adjoining work and refinish cut surfaces or repair damaged finish
at cuts.
3.02
ADJUSTMENT AND C W I N G
A Repair damaged and defective cabinets and tops where to eliminate defects
functionally and visually; where not possible to repair, replace woodwork. Adjust joinery for
uniform appearance.
B. Clean, lubricate, and adjust hardware.
C. Clean woodwork on exposed and semi exposed surfaces.
finishes to restore damaged or soiled areas.
Touch up factory-applied
3.03 PROTECTION
A. Provide final protection and maintain conditions, in a manner acceptable to manufacturer
and Installer, that ensures that woodwork is being without damage or
deterioration at time of Substantial Completion.
CENTURY CENTER
RESTROOM REMODEL
-
CASEWORK 06403 5
COUNTERTOP COLOR
SCHEDULE
BASE BID / COLOR
ROOM
Dl15
B115A
Dl41
D202
B208A
MEN
SlNK AREA
MEN
MEN
SlNK AREA
ALTERNATE BID / COLOR
------------------------
ZODIAQ / WOODLAND GREY
--------------------------------------B116 WOMEN
BI16A MAKE-UP
Dl42 W O M W
ZODIAQ / MINERA PEARL
D203 WOME
D203A MAKE-UP
B207A MAKE-UP
ZODIAC / SMOKEY TOPAZ
CORIAN / SAGEBRUSH
--..---------------NO ALTERNATE
---------------------
------------------------------------------
-------------------------------------------"
CORIAN / SONORA
---------------
Note: existing vanities to remain under Alternates 1 b. 2.
END OF SECTlON 06403
CENTURY CENTER
RESTROOM REMODEL
-
CASEWORK 06403 6