hanger options - Alera Lighting

advertisement
Hanger Options
Pendant Options
Nut
SS18 - Stem, Swivel=$12.90 Per stem adder
45° Swivel from Vertical
Swivel
Suspension
Plate
Suspension
Plate
PMB - Feed Stem w/j-BOx, Non-Swivel=
contact factory for pricing
J-Box with fixture
stud (furnished by
electrical contractor)
Crossbar
Canopy
Ceiling Canopy
with Slip Ring
Canopy
Stem (⅝" OD)
Stem (⅝" OD)
Stem (⅝" OD)
K.O. in fixture
channel
⅜" IP Hex Nut
Slip Ring
with Screw
Screw
Locknut
Locknut
Washer
Wastenut
Locknut
Locknut
PMS - Sloped Ceiling Stem=Contact factory
for pricing
45° Swivel from Vertical
Small Hex Nut
PMR - Earthquake Stem w/cable= $17.50 per
stem adder
45° Swivel from Vertical
⅜" IP
Hex Nut
Pendant Options available for:
F4
Ceiling
Bracket
IB66
Visual Leveling
Scale
IT4
Ceiling
Bracket
IT6
Visual Leveling
Scale
IT9
MS6
Canopy
Canopy
Stem (⅝" OD)
K.O. in fixture
channel
Stem (⅝" OD)
Rocker
Fitting Kit
Wastenut Kit
Standard ⅝"
K.O. in
fixture
channel
MS8
S6
S8
For pendant mounting on products
not listed here, please contact factory.
Cable Earthquake
Specifications subject to change without notice.
Technical
Technical
S18 - Stem, Non-Swivel= $11.05 per stem adder
Hanger Options
Cable Options
Non-Feed
T-Bar
Caddy Clip*
J-Box Strap w/
ground screw
Ceiling Plate 5"
Wastenut Kit Required
T-Bar
Caddy Clip*
Stud
F4, IB66, IT4*, IT6*, IT9*, ME*
MS6, MS8, S6, S8
Ceiling Plate 2"
(optional)
*Indirect and direct/indirect fixtures.
Ceiling Plate 5"
(standard)
Bushing
Coiled Cord
(optional)
Cable Assembly
(see options below)
Note:
Do not
over-torque
safety nut.
Finger
tighten only
and wrench
tighten 1/2
turn further
but no
more.
SJT Power Cord
Bushing
Wastenut Kit if required
Cable Assembly
(see options below)
Wastenut Kit Not Required
Note: Do not overtorque safety nut.
Finger tighten only
and wrench tighten
1/2 turn further but
no more.
ASC , ALS1, CV2, IDC2, IQ1, IT43,
IT63, IT93, LEX2, MAX2,
QST2, SLS1, SOLO1
1
⅜" IP Hex Nut
¼" IP Hex Nut
3
¼" IP Hex Nut, direct fixtures require locknut.
1
2
Wastenut Kit if required
*Add TBAR in the suffix of the catalog number if required.
Cable Assembly Options
FCM
CM
CM
ASC, ASCL, CVL 2-L, QST
CV, CVPL, CVSL, IDC, LEX, MAX
CM
CM
CM
IQ
CPLS, CVL 1T8, CVL 3T8,
NPLS, NVS, PLK, PPLS
ALS, ARC, BENE, SLS, SOLO
T-Bar Mounting Option
Junction Box Accessory for Drop Ceiling Installation
Alera cable hangers can be installed directly to the T-Bar grid. The IDS clip
and additional length of SJT cord will be supplied when the suffix “TBAR” is
added to the catalog number.
#93016675- ordered separately
Feed End
• Complies with Article
400.8 NEC with issues
concerning cords thru
drop ceilings
Non-Feed End
Support Wire to
Structure (by others)
4" Octagonal J-Box
by others
¼" Flex to Junction Box
(by others)
T-Bar Clip with
¼-20 Screw
5" Canopy
Ceiling Tile (by others)
Strain Relief
Bushing
¼-20 Internal Thread
Ceiling Coupler
Cable Hanger
Assembly
Connect feed wires to
fixture as required
T-Bar Clip
T-Bar (by others)
5" Canopy
(2” Canopy option)
Aircraft Cable
Feed Cord
Snap-In
Bushing
• UL Listed 2⅛" deep
octagonal box to mount
over T-Bar
• Independent support tab
provided on back of box
for independent support
for both junction box and
attached lighting fixture.
• Ground screw hole
location and ½"
knockouts located for
easier access after
mounting.
• Knockouts provided for
regular type ceiling tiles
to keep junction box flush
with ceiling tile edge.
3.56" Square
Drop Ceiling
Junction Box
Drop Ceiling
T-Bar By Others
(For Drop Ceiling
Application)
2.16"
Height
¼"-20 × ¾"L
Philips Flat
Head Screw
Countersunk
¼"-20 Gem Bar
3.5" C to C
8/32" Mounting
Screws
Specifications subject to change without notice.
Technical
Technical
Feed
Download