Sandvik LH517
TECHNICAL SPECIFICATION
LH517-18 (12.11.2010)
1/3
Note: Dimensions subject to bucket options
Sandvik Mining and Construction reserves the right to change this
specification without further notice
ISO 9001
ISO 14001
CERTIFICATED
FIRM
CERTIFICATED
FIRM
Sandvik Mining and Construction Oy
P.O. Box 434
20101 Turku, Finland
Tel. +358 205 44 131
Fax +358 205 44 130
www.smc.sandvik.com
Sandvik LH517
Main dimensions
TECHNICAL SPECIFICATION
LH517-18 (12.11.2010)
2/3
Standard axles
Total length
Width without bucket
Maximum width
Std. height with safety canopy or cabin
11 120 mm (438")
2 785 mm (110")
3 000 mm (118")
2 754 mm (109")
Front axle
Rear axle
Weights
Dana 53R300, Posi Stop brakes,
Posi-Torq differentials with springs, fixed
Dana 53R300, Posi Stop brakes,
Posi-Torq differentials with springs,
oscillating ±8°.
Operating weight
44 030 kg (97 000 lb)
Total loaded weight
61 200 kg (135 000 lb)
Shipping weight
43 700 kg (98 600 lb)
Axle weights without load:
Front axle
18 270 kg (40 210 lb)
Rear axle
25 760 kg (56 800 lb)
Axle weights with load:
Front axle
45 070 kg (99 360 lb)
Rear axle
16 130 kg (35 560 lb)
Unit weight is dependent on the selected options
Standard tyres
Capacities
ROPS/FOPS Safety Cabin 21 with air condition.
Height
2754 mm (108”)
Tramming capacity
Breakout force, lift
Breakout force, tilt
Tipping load
Bucket std.
17 200 kg (38 000 lb)
343 kN (35 000 kg) (77 160 lb)
289 kN (29 450 kg) (64 930 lb)
35 500 kg (78 260 lb)
7 m3 (9,2 yd3), GET -abrasion
system
Bucket motion times
Raising time
Lowering time
Tipping time
8,3 sec.
4,3 sec.
2,0 sec.
Driving speeds forward and reverse
1st gear
2nd gear
3rd gear
4th gear
5,4 km/h (3.4 mph)
9,4 km/h (5.8 mph)
16,0 km/h (9.9 mph)
27,0 km/h (16.8 mph)
Frame
Rear and front frame
Material
Central hinge
Material
Tanks are welded to frame.
Welded steel construction
Raex Multisteel N (St/Fe 355)
Adjustable upper bearing
Raex Multisteel N (St/Fe 355)
Standard engine
Diesel engine
Output
Torque
Number of cylinders
Displacement
Cooling system
Combustion principle
Electric system
Air filtering
Exhaust system
Fuel tank capacity
Volvo TAD1361VE,
MSHA approved
285 kW (388 hp) / 1900 rpm
1939 Nm / (1430 lbf ft) / 1350 rpm
In line 6
12.78 l
Water cooled
Four stroke, direct injection, turbo
with intercooler
24 V starter and accessories
Donaldson
Catalytic purifier and muffler,
Double wall exhaust pipe
485 l (128 gal)
Standard converter
Dana C9602
Without lock-up
Standard gearbox
Dana 6422
Power shift (electrical gear
shift control) gear box with
modulation, 4 + 4 speeds
Sandvik Mining and Construction reserves the right to change this
specification without further notice
Size and
26.5x25 L-5, 34ply
type
Brand and type subject to availability)
Other type of tyres available to user’s choice. In certain
applications the productive capabilities of the loader may
exceed the TKPH value given by tyre manufacturer.
Sandvik Mining and Construction Oy recommends that the
user consult their tyre supplier to evaluate conditions and to
find the best solution for application.
Standard Cabin
Controls
Joystick bucket & steering, gear selector buttons on the
joystick. Automatic gear selection.
Heavy duty switches
Steering hydraulics
Full hydraulic, centre-point articulation, power steering with
two double acting cylinders. Steering controlled by electric
joy-stick, interlock protection. Emergency steering is
optional.
Turning angle
±42,5°
Turning radius with std bucket Inner right 3540 mm (139")
Inner left 3420 mm (135”)
Outer 7235 mm (285")
Main components in steering system:
Main valve
Servo control valve
Steering hydraulic cylinders
2 pcs, 125 mm (4.9")
Steering pump
piston type, Rexroth
Pressure settings:
Steering hydraulics, main relief valve
12.0Mpa(120 bar)
Shock load valves
17,5Mpa(175 bar)
Bucket hydraulics
Joy-stick bucket and boom control (electric). Lift by two ø180
mm cylinders. Tilt by one ø220 mm cylinder with Z-linkage.
The bucket hydraulics has one piston pump, which delivers
oil to the bucket hydraulic main valve. The oil flow from
steering hydraulic pump is directed to bucket hydraulics
when steering is not used.
Boom system
Z-link
Lift cylinders
2pcs, ø180 mm (7.1”)
Tilt cylinder
1pcs, ø220 mm (8.7”)
Pressure setting for:
Servo circuit
3,5 MPa (35 bar)
Bucket hydraulics
28,0 MPa (280 bar)
Shock load valves
30,0 MPa (300 bar)
Main components:
Servo control valve
Main valve
Pump for bucket hydraulics
Fittings
ORFS
Hoses
High temperature
ISO 9001
ISO 14001
CERTIFICATED
FIRM
CERTIFICATED
FIRM
Sandvik Mining and Construction Oy
P.O. Box 434
20101 Turku, Finland
Tel. +358 205 44 131
Fax +358 205 44 130
www.smc.sandvik.com
Sandvik LH517
Standard brakes
Service brakes are spring applied, hydraulically released
multidisc wet brakes (Posi-Stop) on all wheels, two separate
circuits for the front and rear axle. Service brakes also
function as an emergency and parking brake. Electrically
driven pump for brake emergency/towing releasing.
Main components in the brake system:
Pressure accumulator
Brake pedal valve
Brake valve
Charging valve
Standard Lubrication system
Centralized manual lubrication
Electrical equipment
Parking lights
Brake lights
Blinkers
Control system
24V, 140 A, Bosch
2 x 12 V, 180 Ah
9 kW, 24V
2 pcs in front, 65W
Nordic lights
2 pcs in rear, 65W
Nordic lights
2 pcs on cabin, 65W
Nordic lights
2 pcs in front (LED lights)
2 pcs in rear (LED lights)
5,7” display, 3 modules,
inbuild system diagnostics
Safety equipment
Seat belt
Lockable main switch
Reverse alarm
External shutdown, 2 pcs in rear
Others
Decal language
3/3
Main Options:
Oil cooler (2 pcs) for hydraulic and transmission oil.
Capability up to 52°C ambient temperature
Hydraulic oil tank capacity
Appr. 320 l (85 gal)
Alternator
Batteries
Starter
Driving and working lights
TECHNICAL SPECIFICATION
LH517-18 (12.11.2010)
* Replaces standard equipment
• * Engine Volvo TAD1361VE, 285kW / (388hp),
Euro Stage 3B / Tier 4i (for EU and Japan)
• * Engine Detroit S60 DDEC IV 298kW (400hp),
MSHA approved
• * Safety cabin with swivel seat (high backrest) & controls
±25° ,
ROPS/FOPS, height 2990 mm, width 2975 mm (without
bucket)
• * Bucket size 6.5 m3 (8.5yd3), width 3070 mm (118”),
GET abrasion system.
• * Bucket size 7.6 m3 (10.0yd3), width 3070 mm (118”),
GET abrasion system.
3
3
• * Bucket size 8.6 m (11.0yd ), width 3070 mm (118”),
GET abrasion system.
• * Automatic central lubrication.
• * Converter with lock-up, Dana SOH.
• Fire suppression system ANSUL, two-tank system with 8
nozzles (CEN) with auto engine shut down
• Fire suppression system ANSUL, two-tank system with 8
nozzles (CEN), CHECKFIRE with auto engine shut down
• Sandvik FS1000 fire suppression system with auto engine
shut down
• Fire extinguisher 12 kg CEN).
• RRC HBC, complete
• Radio remote control interface HBC
• RRC recovery kit, hook included.
• Ride control system with boom float
• Emergency steering (CEN).
• Accordance with CE-norms (CEN).
• Disassembly needed shaft dim: TBA
• Rotating beacon (CEN with RRC)
• Load weighing device, Tamtron PKVS 300 M
• Load weighing device, Tamtron PKVS 300 C
• Wiggins fill set (hydr., transm., eng. oil)
• Wiggins fuel fill system
• CatBase/LinkOne spare part manuals and additional
Instructions, Workshop, Spare part manuals, ToolMan CD’s
are available.
EU-languages
Standard manuals
Instructions Manual
-Operator's Manual
-Maintenance Manual
Parts Manual
Service and Repair Manual
ToolMan CD, (2 pcs)
-Instructions Manual
-Operator's Manual
-Maintenance Manual
-Parts Manual
-Service and Repair Manual
EU-languages
EU-languages
English
English
In pdf format
Sandvik Mining and Construction reserves the right to change this
specification without further notice
ISO 9001
ISO 14001
CERTIFICATED
FIRM
CERTIFICATED
FIRM
Sandvik Mining and Construction Oy
P.O. Box 434
20101 Turku, Finland
Tel. +358 205 44 131
Fax +358 205 44 130
www.smc.sandvik.com