Low duty mode in a legacy support femtocell BS
Document Number:
IEEE C80216m-09/0409
Date Submitted:
2009-03-02
Source:
Jin Lee, Sungho Moon, Ronny (Yong ho) Kim, Kiseon Ryu and Jinsam Kwak
Email:{jins978,msungho,ronnykim}@lge.com
LG Electronics
Venue:
IEEE 802.16 session #60, Vancouver, Canada
Re: IEEE 802.16m-09/0008, “IEEE 802.16m Internal Documents Configurations Control Procedure (CCP)”
Purpose:
Discussion and Approval for IEEE 802.16m SDD Text
Notice:
This document does not represent the agreed views of the IEEE 802.16 Working Group or any of its subgroups. It represents only the views of the participants listed in
the “Source(s)” field above. It is offered as a basis for discussion. It is not binding on the contributor(s), who reserve(s) the right to add, amend or withdraw material
contained herein.
Release:
The contributor grants a free, irrevocable license to the IEEE to incorporate material contained in this contribution, and any modifications thereof, in the creation of an
IEEE Standards publication; to copyright in the IEEE’s name any IEEE Standards publication even though it may include portions of this contribution; and at the IEEE’s
sole discretion to permit others to reproduce in whole or in part the resulting IEEE Standards publication. The contributor also acknowledges and accepts that this
contribution may be made public by IEEE 802.16.
Patent Policy:
The contributor is familiar with the IEEE-SA Patent Policy and Procedures:
<http://standards.ieee.org/guides/bylaws/sect6-7.html#6> and <http://standards.ieee.org/guides/opman/sect6.html#6.3>.
Further information is located at <http://standards.ieee.org/board/pat/pat-material.html> and <http://standards.ieee.org/board/pat >.
1
Motivation
•
When a CSG femtocell BS supports both an YMS and AMS, frame configuration of
the femtocell BS will be the same as a legacy support macro BS (shown in Fig 1.)
16e
preamble
16e DL
16m
Switching
A-PREAMBLE Point
16m DL
16e
UL
5 ms Radio
Frame
•
16m
16e
preamble A-PREAMBLE
Switching
Point
16e
preamble
Switching
16m
A-PREAMBLE Point
16m UL
5 ms Radio
Frame
5 ms Radio
Frame
Fig 1. Legacy support macro BS
However,
• If none of the CSG YMS exists within the overlay macro BS of its CSG Femtocell
BS,
– Unnecessary access signals occur from non-CSG YMSs in the Lzone
– Inessential 16e signals via Lzone (power consumable and outbreak of interference) are
transmitted
• In case where none of the CSG AMS exist the overlay macro BS of its CSG
Femtocell BS, the non CSG AMSs will keep trying to access the femtocell BS in
the MZone
•
Therefore, a CSG femtocell BS should support low duty mode (defined in SDD 17.7)
of L/MZone separately upon the presence of a CSG YMS/AMS within the overlay
2
macro BS of its CSG Femtocell BS
Low duty mode in a legacy support femtocell BS
 Low duty mode of LZone
 If none of the CSG YMSs are
within the overlay macro BS of
its CSG Femtocell BS,
 Frame configuration would be :
16e
preamble
16m
A-PREAMBLE
16m DL zone
 Low duty mode of MZone
 If none of the CSG AMSs are
within the overlay macro BS of
its CSG Femtocell BS,
 Frame configuration would be :
16m UL zone
5 ms Radio
Frame
Fig 2. Low duty mode of LZone
16e DL
16e
UL
5 ms Radio
Frame
Fig 3. Low duty mode of MZone
 Advantages
 To remove interference to non CSG (Y/A)MSs
 To decrease unnecessary access signaling from non CSG (Y/A)MSs
Usage Scenarios
16e DL
CSG list
16m 16e
DL UL
16m
UL
Macro BS 1
CSG list
16m
DL
16m
UL
111
222
111
222
Macro BS 1
AMS: 111
YMS: 222
AMS: 111
YMS: 222
Case 1
Macro BS 2
16e DL
16e
UL
Macro BS 2
Case 2
Macro BS 1
Macro BS 1
Turn off Radio
CSG list
CSG list
111
222
111
222
YMS: 222
AMS: 111
Macro BS 2
YMS: 222
Case 3
Case 4
Macro BS 2
AMS: 111
Proposed SDD Text
 17.7 Low –duty Operation Mode
 When an MS leaves or enters the overlay macro BS of its CSG Femtocell BS,
the network may signal the CSG Femtocell BS to enter low-duty operation
mode or normal operation mode, respectively. Handover signaling or location
update signaling may trigger such operation. In case a CSG Femtocell BS
supports both AMS and YMS, the network may signal the CSG Femtocelcell
BS to stop or start transmission of LZone/MZone when an YMS/AMS leaves
or enters the overlay macro BS of its CSG Femtocell BS respectively. The
CSG Femtocell BS switches between the low-duty operation mode and the
normal operation mode when it receives requests from the overlay macro BS,
the core network, or an MS for network entry, HO, or the exit of the sleep
mode.The low-duty operation mode shall not impact the support for
emergency service and E911.