IEEE C802.16m -09/1283r2
Project
IEEE 802.16 Broadband Wireless Access Working Group <http://ieee802.org/16>
Title
Multi-Carrier DG Harmonized Text Proposal - MAC
Date
Submitted
2009-07-16
Source(s)
I-Kang Fu, Jaehee Cho
Multi-Carrier DG Chairs
Re:
IEEE 802.16m-09/0028r1, “Call for Comments and Contributions on Project 802.16m
Amendment Content.”
Abstract
This document contains the harmonized text proposal on MAC sections by Multi-Carrier DG
participants through email or conference call discussions.
Purpose
Harmonized text proposal by Multi-Carrier DG for possible adoption by TGm
Notice
Release
Patent
Policy
IK.Fu@mediatek.com
jaehee1.cho@samsung.com
This document does not represent the agreed views of the IEEE 802.16 Working Group or any of its subgroups. It
represents only the views of the participants listed in the “Source(s)” field above. It is offered as a basis for
discussion. It is not binding on the contributor(s), who reserve(s) the right to add, amend or withdraw material
contained herein.
The contributor grants a free, irrevocable license to the IEEE to incorporate material contained in this contribution,
and any modifications thereof, in the creation of an IEEE Standards publication; to copyright in the IEEE’s name
any IEEE Standards publication even though it may include portions of this contribution; and at the IEEE’s sole
discretion to permit others to reproduce in whole or in part the resulting IEEE Standards publication. The
contributor also acknowledges and accepts that this contribution may be made public by IEEE 802.16.
The contributor is familiar with the IEEE-SA Patent Policy and Procedures:
<http://standards.ieee.org/guides/bylaws/sect6-7.html#6> and
<http://standards.ieee.org/guides/opman/sect6.html#6.3>.
Further information is located at <http://standards.ieee.org/board/pat/pat-material.html> and
<http://standards.ieee.org/board/pat>.
1
IEEE C802.16m -09/1283r2
Multi-Carrier DG Harmonized Text Proposal - MAC
I-Kang Fu, Jaehee Cho
Multi-Carrier DG Chairs
Note:
The text in BLACK color: the existing text in AWD
The text in RED color: the removal of existing AWD text
The text in BLUE color: the new text added by Multi-Carrier DG
------------------------------------------------------------Start of the Text-------------------------------------------------------15. Advanced Air Interface
15.2.9 Multi-carrier operation
15.2.9.1 Multi-carrier Types and Operational Modes
The carriers involved in multi-carrier mode of operation from an AMS point of view are of two types:
• A primary carrier is a carrier used by the ABS to exchange traffic and PHY/MAC control signaling (e.g.,
MAC management messages) with an AMS. An ABS may be deployed with multiple carriers but each AMS
in the ABS has only one primary carrier which is also used when AMS is operating in single carrier mode.
• Secondary carriers are additional carriers which the AMS may use for traffic, only per ABS’s specific
commands and rules received on the primary carrier.
In the multicarrier operation a common MAC can utilize radio resources in the primary carrier and one or more
of the secondary carriers, while maintaining full control of AMS mobility, state and context through the primary
carrier.
Based on the primary and/or secondary usage and target services, the carriers of a multi-carrier system may be
configured differently as follows:

Fully configured carrier: A standalone carrier for which all control channels including synchronization,
broadcast, multicast and unicast control signaling are configured. Fully configured carrier supports both single
carrier AMS and multi-carrier AMS.

Partially configured carrier: A carrier configured for downlink only transmission in TDD or a downlink
carrier without paired UL carrier in FDD mode. . Such supplementary carriers may be used only in conjunction
with a primary carrier and cannot operate standalone to offer IEEE 802.16m services for an AMS. Whether a
carrier is fully configured or partially configured is indicated using Advanced Preamble of the carrier. The AMS
shall not attempt network entry or handover to partially configured carrier
A primary carrier is fully configured while a secondary carrier may be fully or partially configured depending on
deployment scenarios. A secondary carrier for an AMS, if fully configured, may serve as primary carrier for
other AMS’s. Multiple AMSs, each with a different primary RF carrier may also share the same secondary
carrier. The following multi-carrier operation modes are identified, which may all or independently be
supported:

Multi-Carrier Aggregation: The multicarrier mode in which the AMS maintains its physical layer
connection and monitors the control signaling on the primary carrier while processing data on the secondary
2
IEEE C802.16m -09/1283r2
carrier. The resource allocation to an AMS may span across a primary and multiple secondary RF carriers. Link
adaptation feedback mechanisms should incorporate measurements relevant to both primary and secondary
carriers. In this mode the system may assign secondary carriers to an AMS in the downlink and/or uplink
asymmetrically based on system load (i.e., for static/dynamic load balancing), peak data rate, or QoS demand.

Multi-Carrier Switching: The multicarrier mode in which the AMS switches its physical layer
connection from the primary to the secondary carrier per ABS’ instruction. The AMS connects with the
secondary carrier for the specified time period and then returns to the primary carrier. When the AMS is
connected to the secondary carrier, the AMS is not required to maintain its physical layer connection to the
primary carrier. This mode is used for switching to partially configured carriers for downlink transmission only
service.
The following is common to all multi-carrier modes of operation:

The system defines N standalone fully configured RF carriers; each fully configured with all
synchronization, broadcast, multicast and unicast control signaling channels needed to support an AMS in single
carrier mode. Each AMS in the cell is connected to and its state being controlled through only one of the fully
configured carriers designated as its primary carrier.

The system may also define M (M >= 0) partially configured RF carriers, which can only be used as
secondary carriers along with a primary carrier, for downlink only data transmissions.

The set of all supported radio carriers in an ABS is called Available Carriers.

The multiple Available cCarriers may be in different parts of the same spectrum block or in noncontiguous spectrum blocks. Support of non-contiguous spectrum blocks may require additional control
information on the secondary carriers.

In addition to information about the (serving) primary carrier an ABS, supporting any multicarrier mode,
also provides AMSs with some basic configuration information about its other available carriers through such
primary carrier. The basic multicarrier configuration Through such messaging the ABS informs AMS’s of the
presence, bandwidth, duplexing, and location in the spectrum for all available carriers to help AMS prepare for
any multicarrier operation involving multiple carriers. The primary carrier may also provide an AMS the
extended information about the configuration of the secondary carrier.
15.2.9.2 MAC operation
15.2.9.2.1 Addressing
A multi-carrier supporting ABS or AMS follows the same MAC addressing mechanism defined in 15.2.1[5].
15.2.9.2.2 Security
A multi-carrier supporting AMS follows the same security procedure defined in 10.6[3]. All the security
procedures between an AMS and an ABS are performed using the AMS’s primary carrier. The security context
created and maintained by the procedures is managed per ABS through the primary carrier.
3
IEEE C802.16m -09/1283r2
15.2.9.2.3 Network Entry
The network entry in multicarrier mode is the same as single carrier mode as defined in 15.2.15, where the AMS
and ABS also indicate their support for multicarrier modes during the registration. An AMS can only perform
network entry (or network re-entry) procedures with a fully configured carrier. Once the AMS detects the APREAMBLE on a fully configured carrier, the AMS may proceed with reading SFH or Extended system
parameters and system configuration information where the ABS indicates its configuration, and its support for
multi-carrier feature.
During the initial network entry, AMS will inform ABS of its support of multi-carrier transmission by REGREQ message and the ABS will indicate if it supports any of multicarrier modes for that AMS through REGRSP message. The basic multicarrier capability exchange uses a two bit code in REG-REQ/RSP message with
the following indications:
b1,b2
Multicarrier Capabilities
00
No MC modes
01
Multicarrier Aggregation
10
Multicarrier Switching
11
Both Multicarrier aggregation and
Switching
The procedure for initialization of an AMS, following network entry, to prepare for subsequent multi-carrier
operation shall be as shown in Figure x. This procedure includes

Obtaining the multicarrier configuration for available carriers at the ABS

Obtaining information about Assigned Carriers consisting of two steps
1. Provide ABS with information on AMS’s supportable carriers and their combined multicarrier
configurations
2. Obtain information about the subset of available carrier, hereby referred to as the Assigned
Carriers, which ABS may utilize in subsequent multicarrier operation for that AMS.
The AMS does not perform any MAC or PHY processing on an assigned carrier until such carrier is
activated per ABS’s direction
The AMS can decide on proceeding with network entry with the current carrier or going to alternative carriers
based on this information. The initial network entry/re-entry follows the procedures defined in 10.8[3] with the
exception of operations described in below.
4
IEEE C802.16m -09/1283r2
Network Entry Process
(defined in 15.2.15)
Including
Basic Multicarrier Capability
Negotiation
during REG-REQ/RSP
Establish provisioned connections
Operational
No
AMS and ABS support
a common MC mode?
Yes
No
Continue with Single Carrier
Procedures
AAI_MC-ADV Received ?
Yes
Send AAI_MC-REQ including the
MC capability negotiation
Receive AAI_MC-RSP including list
of the assigned carrier(s)
AMS/ABS Ready for Multicarrier
Operation
Figure x - AMS initialization overview to support multi-carrier transmission
15.2.9.2.3.1 AMS’s Obtaining MC Configuration
The ABS will broadcast the SFH for each carrier with the format defined in 15.3.6.2.1. The ABS indicates if it
supports any of multicarrier modes to AMS in a cell. . The ABS shall also provides AMS’s with basic radio
configuration for other available carriers in the ABS through AAI_MC-ADV a MAC management message.
This message is periodically broadcast by BS, which includes the supporting any multicarrier mode and the
configurations supported by ABS. The same configuration information may also be unicast per AMS request.
The multi-carrier configuration information is relevant to and shall may be used by all AMS’s in any of
multicarrier modes or in single carrier mode.
The multicarrier configuration information includes information such as center frequency, duplexing mode,
bandwidth and other parameters if different than the serving carrier and it also assigns each carrier a physical
carrier index, which is used by ABS and AMS for any reference to any available carrier. The configuration
information is applicable to all MS’s supporting any of multicarrier modes.
15.2.9.2.3.1.1 AAI_MC-ADV (Multi-Carrier Advertisement) Message
ABS shall periodically broadcast AAI_MC-ADV message for the reception by all AMS. ABS may also send this
5
IEEE C802.16m -09/1283r2
message to AMS in unicast manner per request.
The following information shall be included in multicarrier configuration information MC-CONFIG-ADV

Physical Carrier Index

Center Frequency (eg. Band Class Index and channel index)

Channel Bandwidth

Carrier Type (fully/partially configured)

Duplexing Mode

Preamble Index
Table xxx AAI_MC-ADV MAC management message format
Field
Size
(bit)
Description
Number of Carrier Groups
4
Groups of contiguous carriers
Uniformity Flag
1
All Carriers have the same Protocol Version, Carrier Type
Duplexing Mode and Transmit Power.
Physical Carrier Index of Current Carrier
6
The carrier that ABS broadcast this message
Multi-Carrier Configuration Index
6
Index associated to Table 648
Start Frequency Assignment Index
6
Frequency Assignment Index of the first carrier in carrier
group #i
Number of Carriers
4
Number of carriers in carrier group #i
For (i=1; i<= Number of Carrier Groups;
i++){
For (j=1; j <= Number of Carriers; j++) {
Physical Carrier Index
6
Preamble Index
6
If (Uniformity Flag == 1) | | (i == 1 && j ==
1) ) {
Protocol Version
2
“00” IEEE 802.16-2009 only mode
“01” IEEE802.16m and IEEE 802.16-2009 mixed mode
“10” IEEE 802.16m only mode
“11” Reserved
Carrier Type
1
“0” for fully configured
“1” for partially configured
Duplexing Mode
1
“0” for TDD
“1” for FDD
6
Transmit Power
6
IEEE C802.16m -09/1283r2
Maximum transmit power level
}
}
}
After successful ranging the AMS follows the capability negotiation procedure. During capability negotiation,
the AMS and ABS shall exchange their multi-carrier capabilities, such as supported multicarrier modes, the
number of supportable RF carriers in the downlink and uplink and maximum throughput. These Capabilities are
negotiated via post authentication as they do not affect network entry and operation in basic single carrier mode
through REG-REQ/RSP messages.
15.2.9.2.3.2 Secondary Carrier Assignment
After the initial network entry procedure defined in 15.2.9.2.3, AMS shall send AAI_MC-REQ message to ABS
if AMS and ABS both support multi-carrier transmission. AMS shall inform ABS its capability on multi-carrier
support by the parameters defined in AAI_MC-REQ message. Based on AMS’s multicarrier capabilities
informed in AAI_MC-REQ, the ABS shall reply AAI_MC-RSP message to may assign one or more carriers
from its available carriers to an AMS as the Aassigned secondary carriers (see 15.2.x.2.11.).
15.2.9.2.3.2.1 AAI_MC-REQ (Multi-Carrier Request) Message
The Multi-Carrier Request Message (AAI_MC-REQ) is sent by the AMS to ABS to request the list of Assigned
Carriers. This message shall include all information about the AMS’s supported multicarrier configurations that
is needed by the ABS to assign carriers to the AMS and activate when needed. AMS cannot send AAI_MC-REQ
until it receives AAI_MC-ADV from serving ABS. The following are the parameters shall be included in
AAI_MC-REQ message:

AMS multi-carrier capability parameters for carrier assignment

List of candidate of assigned carriers

Support of data transmission over guard sub-carrier
15.2.9.2.3.2.2 AAI_MC-RSP (Multi-Carrier Response) Message
Based on information provided by the AMS on AAI_MC-REQ message, the ABS shall respond to AMS
through the AAI_MC-RSP message to provide AMS with information about its assigned carriers. The
following are the parameters shall be included in AAI_MC-RSP message:

List of assigned carrier

Support of data transmission over guard sub-carrier
The AAI_MC-RSP (Multi-Carrier Response) Message is typically sent to AMS in response to AAI_MC-REQ
message, but it may also be sent by ABS to an AMS to update the list of assigned carriers in unsolicited manner.
The AMS may not be able to communicate with the ABS over the secondary carrier(s), if it needs ranging to
7
IEEE C802.16m -09/1283r2
adjust time/frequency synchronization and power for the carrier(s). Under the assumption of high channel
correlation between the carriers, the transmission parameters of secondary carrier(s) could be quite similar with
those of primary carrier. Since the AMS already completed the network entry with the ABS over the primary
carrier, it does not need to perform the initial ranging over the secondary carrier(s). Therefore, over the
secondary carrier(s), the periodic ranging instead of initial ranging may be performed. So once secondary
carriers are assigned, the AMS may perform the periodic ranging over the assigned secondary carrier(s) if
directed by the ABS.
When the AMS omit the ranging for the secondary carrier(s), the AMS may use the same timing, frequency and
power adjustment parameters for the secondary carrier(s) as in the primary carrier. The AMS may perform the
fine timing, frequency and power adjustment on the secondary carrier(s) through measuring the synch channel
and/or pilot on the secondary carrier(s).
15.2.9.2.4 Ranging
In some cases, the AMS may not be able to communicate with the ABS over the secondary carrier(s) without
ranging to adjust time/frequency synchronization and power for the carrier(s). If the channel correlations
between the primary and the secondary carriers are very high, the transmission parameters of the secondary
carrier(s) could be quite similar with those of primary carrier. If the AMS already completed the network entry
with the ABS over the primary carrier, it does not need to perform the initial ranging over the secondary
carrier(s). Therefore, only the periodic ranging instead of initial ranging may be performed over the secondary
carrier(s). Once the secondary carriers are activated, the AMS may perform the periodic ranging over the active
secondary carrier(s) if directed by the ABS.
When the AMS omit the ranging for the secondary carrier(s), the AMS may use the same timing, frequency and
power adjustment parameters for the secondary carrier(s) as in the primary carrier for initial transmission. The
AMS may perform the fine timing, frequency and power adjustment on the secondary carrier(s) through
measuring the synch channel and/or pilot on the secondary carrier(s).
CDMA initial/periodic ranging with a fully configured carrier shall be the same as defined in 6.3.10.3.1,
6.3.10.3.2[1]. Periodic ranging may only be performed on the assigned activated secondary carrier(s) if directed
by the ABS. Upon moving to a target ABS, the AMS shall initiate CDMA handover ranging as defined in
section 15.2.5.2.5.1[5]. CDMA handover ranging shall be done only with one of the fully configured carriers of
target ABS. Upon moving to a target ABS, the AMS shall initiate CDMA handover ranging as defined in
section 15.2.5.2.5.1[5].
15.2.9.2.5 MPDU processing
The construction and transmission of MAC PDU is the same as that in single carrier operation.
For each service flow the ARQ operates for a common MAC as defined in 10.4[3].
15.2.9.2.5.1 MAC segmentation
MAC data (15.3.2.6) shall be processed as defined for single carrier physical layer operation and can be mapped
to data region (15.3.2.6) in one of primary or secondary carriers. The A-MAP IE shall be sent through the carrier
where the OFDMA data region is located. The A-MAP IE is the same as the one defined in 15.3.6.5.2.
8
IEEE C802.16m -09/1283r2
15.2.x.2.6 Bandwidth Request and Resource Allocation
15.2.9.2.6.1 Bandwidth Request
All bandwidth requests are transmitted on the AMS’s primary carrier using the assigned bandwidth request
channel following the same procedures as defined in 15.2.2[5]. Bandwidth request using piggyback may be
transmitted in MPDUs over the secondary carrier(s) as well as the primary carrier.
15.2.9.2.6.2 Resource Allocation
The ABS may allocate downlink or uplink resources which belong to a specific carrier or a combination of
multiple carriers based on available resources, QoS requirements and other factors. The multicarrier resource
assignment for carrier aggregation can use the same A-MAP IE’s as single carrier mode, where A-MAP
messages for each active carrier are transmitted in the respective carrier.
15.2.9.2.7 QoS and connection management
The STID and all FIDs assigned to an AMS are unique identifiers for a common MAC and used over all the
carriers of the AMS. The service setup/change messages (i.e., DSx messages) are transmitted only through the
AMS’s primary carrier. The service flow is defined for a common MAC entity and AMS’s QoS context
represented by an SFID is applicable across primary carrier and secondary carrier(s) and collectively applied to
all carriers of the AMS.
15.2.9.2.8 DL CINR report operation
An ABS may assign CQI channels to each carrier of an AMS. When CQI channel is assigned, the AMS reports
CINR for a carrier over the assigned CQI channel of the corresponding carrier. ABS may also direct AMS to
report CINRs of active carriers through CQI channel(s) on the primary carrier. When measurement/report MAC
messages are used for DL CINR report operation, the messages are transmitted on the AMS’s primary carrier.
The measurement/report MAC message may contain CINR reports for all carriers or for each carrier of the
AMS.
15.2.9.2.8.1 MAC management messages for CINR report in multi-carrier
15.2.9.2.9 Handover
The multi-carrier handover (MCHO) is defined as the handover procedure which involves multiple radio
carriers. An AMS with multi-carrier capability may follow the single-carrier handover procedure per section
15.2.56. It may also decide to perform MCHO procedure as defined in this section.
15.2.9.2.9.1 Network topology acquisition
15.2.9.2.9.1.1 Network topology advertisement
The AAI_NBR-ADV message shall carry neighbor ABS’s multi-carrier configuration information to facilitate
AMS’s scanning of neighbor ABSs’ fully configured carriers.
15.2.9.2.9.1.2 AMS scanning of target carriers
The AMS with multi-carrier capability may perform the single-carrier scanning procedure per section 15.2.5.1.2.
It may also perform multi-carrier scanning procedure, i.e. scanning procedure which involves multiple radio
carriers, as defined in this subsection.
9
IEEE C802.16m -09/1283r2
The AMS scans each fully configured carrier of the neighbor ABSs as advertised in the AAI_NBR-ADV
message. The AMS may also scan other fully configured carriers of the serving ABS which are not in use by the
AMS. Figure 403 illustrates the example message flows for neighbor ABS advertisements and scanning of fully
configured carriers of serving and neighbor ABSs.
ABS#1 (serving)
Full conf.
Carrier#1
AMS
Full conf.
Carrier#2
ABS#2
Full conf.
Carrier#1
Full conf.
Carrier#2
ABS#3
Full conf.
Carrier#1
Full conf.
Carrier#2
AAI_NBR-ADV
(N_Neighbors=2)
(Multi-carrier configuration)
By AMS
request only
AAI_SCN-REQ
(Scan duration = N frames,
Interleaving interval = P frames,
Iteration=T times)
AAI_SCN-RSP
(start frame = M frames)
(duration = N frames)
M frames
Synchronize with carrier #1 of ABS #2
Synchronize with carrier #2 of ABS #2
Iteration #1
Scanning interval
duration = N frames
Synchronize with carrier #2 of ABS #1
Nonscanning interleaving
interval (P frames)
Synchronize with carrier #1 of ABS #3
Synchronize with carrier #2 of ABS #3
Data traffic (if any)
Additional alternations
of scanning interval and
interleaving intervals
Figure 403 — Example message flows for neighbor ABS advertisement and scanning of fully configured
carriers of serving and neighbor ABSs.
An AMS capable of concurrently processing multiple radio carriers may perform scanning with neighbor ABSs
using one or more of its available radio carriers without interruption to its normal communication with the
serving ABS on the primary carrier and/or secondary carriers. In this case, the AMS may inform the serving
ABS through AAI_SCN-REQ its carriers AMS and ABS may negotiate through AAI_SCN-REQ/RSP messages
the radio carriers to be assigned for scanning operations to avoid resource allocation on those carriers, as
illustrated in Figure 404. The physical carrier index should will be included in AAI_SCN-REQ/RSP/REP.
1
0
IEEE C802.16m -09/1283r2
AMS
Primary
carrier
ABS#1 (serving)
Full conf.
Carrier#1
Carrier#2
Full conf.
Carrier#2
ABS#2
Full conf.
Carrier#1
Full conf.
Carrier#2
ABS#3
Full conf.
Carrier#1
Full conf.
Carrier#2
AAI_NBR-ADV
(N_Neighbors=2)
(Multi-carrier configuration)
AAI_SCN-REQ
(Scan duration = N frames)
(ID of carriers for scanning)
AAI_SCN-RSP
(start frame = M frames)
(duration = N frames)
Synchronize with
carrier #2 of ABS #1
AMS continues normal
operation with serving
ABS on primary carrier
Scanning interval
duration = N frames
M frames
Synchronize with carrier #1 of ABS #2
Synchronize with carrier #2 of ABS #2
Synchronize with carrier #1 of ABS #3
Synchronize with carrier #2 of ABS #3
Figure 404 — Example message flows for performing scanning using available radio carriers of the AMS while
maintaining normal communication with its serving ABS
15.2.9.2.9.2 Multi-carrier handover (MCHO) procedure
The multi-carrier handover (MCHO) is defined as the handover procedure which involves multiple radio
carriers, as described in this section.
15.2.9.2.9.2.1 MCHO preparation
An AMS in multi-carrier operation follows the handover operations defined in 15.2.5.2. MAC management
messages in relation with handover preparation and initiation between the AMS and the serving ABS are
transmitted over the primary carrier of the AMS.
During HO preparation, the AMS may request or be requested by the serving ABS to perform MCHO procedure
through AAI_HO-REQ/AAI_HO-CMD messages. the AMS may indicate its multi-carrier capability through
AAI_MSHO-REQ or AAI_HO-IND messages. The ABS may also inform AMS the multi-carrier configurations
of one or more potential Serving ABS informs AMS the carrier information (e.g. target primary carrier index) of
the target ABSs through AAI_BSHO-CMD message. If the target ABS is supporintg multicarrier mode,
additional information may be included in the AAI_MSHO_REQ, AAI_BSHO_CMD and AAI_HO_IND
messages. The serving ABS may communicate with target ABS(s) to help AMS obtain the assigned secondary
carriers before handover execution. The serving ABS will forward the information received from AAI_MCREQ message to the target ABS for secondary carrier pre-assignment. The serving ABS will reply the secondary
carrier pre-assignment results to AMS.
15.2.9.2.9.2.2 MCHO execution and network re-entry
The AMS with multi-carrier capability follows the network re-entry procedure per section 15.2.5.2.5. The AMS
1
1
IEEE C802.16m -09/1283r2
may use the original primary carrier for network re-entry to the target ABS, as illustrated in Figure xx3. It may
also use another carrier different from its original primary carrier for network re-entry procedures, as illustrated
in Figure xx4. In both cases, if the Multi-carrier_Mode and HO_Reentry_Mode in AAI_BSHO-CMD message
is are set to 1, the AMS maintains normal communication with the serving ABS on another carrier not
performing network re-entry procedure. In this case, Disconnect_time should be long enough that network
reentry procedure to target ABS can be completed prior to the expiration of Disconnect_time. In case of
AAI_HO-CMD message with multiple target ABS and carriers, the physical index of each candidate carrier
provided by each target ABS should also be indicated in the AAI_BSHO-CMD message The AMS may inform
the serving ABS through AAI_HO-IND the carrier to be used for network re-entry operations to avoid resource
allocation by the serving ABS on that carrier.
Serving
ABS
AMS
Target
ABS
AAI_MSHO-REQ
AAI_BSHO-CMD
AAI_HO-IND
Network re-entry to T-ABS
Data communication with S-ABS
during network re-entry
Data path established
Data path established
Radio
carrier 1
Radio
carrier 2
Serving
primary
carrier
Serving
secondary
carrier
Target
primary
carrier
Target
secondary
carrier
Figure 405 — A call flow for multi-carrier HO in which the AMS performs network re-entry to the target ABS
on one radio carrier while maintaining communication with the serving ABS on another carrier.
Serving
ABS
AMS
Target
ABS
AAI_MSHO-REQ
AAI_BSHO-CMD
AAI_HO-IND
Network re-entry to T-ABS
Data communication with S-ABS during
network re-entry
Data path established
Data path established
Radio
carrier 1
Radio
carrier 2
Serving
primary
carrier
Serving
secondary
carrier
1
2
Target
primary
carrier
Target
secondary
carrier
IEEE C802.16m -09/1283r2
Figure 406 — A call flow for multi-carrier HO in which the AMS performs network re-entry on the target
primary carrier which is different from the serving primary carrier
From AMS point of view, if network entry is completed (see 15.2.5), the AMS shall stop communicating with
the serving ABS. Then, the AMS may send UL data or BW-REQ message to the target ABS.
The Serving ABS may negotiate with the Target ABS for secondary carrier pre-assignment. In this case, the preassignment information is forwarded to the AMS by the Serving ABS through AAI_HO-CMD message, and
part of the pre-assigned secondary carriers may be activated if the AMS sends AAI_CM-IND message to the
target ABS after network re-entry. Before secondary carrier pre-assignment, the Serving ABS shall forward the
multi-carrier capability of the AMS to the Target ABS via backbone.
AMS
S-ABS
T-ABS
Backend
Carrier N
Carrier 2
Carrier 1
Backend
Carrier N
Carrier 2
Carrier 1
Carrier N
Carrier 2
Carrier 1
Primary
Data communication over primary carrier
1st active secondary carrier
Nth active secondary carrier
AAI_HO-REQ
HO request
(for multiple carriers)
HO response with carrier
assignment information
AAI_HO-CMD with target ABS carrier
assignment information
Ranging to the target primary carrier
Optional ranging to the pre-assigned secondary carrier
Optional ranging to the pre-assigned secondary carrier
Remaining network reentry procedure on target primary carrier
Primary carrier established
1st secondary carrier activated
Nth secondary carrier activated
Figure 40X – A call flow for multi-carrier HO with secondary carrier pre-assignment
If secondary carrier pre-assignment is not allowed, then the AMS follows the operation of secondary carrier
assignment (see 15.2.9.2.3.2) and carrier activation (see 15.2.9.2.11.1) after the AMS completes its network reentry with the target ABS.
15.2.9.2.9.2.3 MAC management messages for MCHO
The support of multi-carrier handover will reuse the same messages as defined in 15.2.5.1, 15.2.5.2, 15.2.5.3
and 15.2.5.4. The parameters to be included into each MAC message to support multi-carrier handover are list
as following.
1
3
IEEE C802.16m -09/1283r2
15.2.9.2.9.2.3.1 AAI_SCN-REQ
The AAI_SCN-REQ message may include the following parameters:

N_Recommended_Carrier_Index: Number of carriers to be scanned at each neighboring ABS.

Recommended_Carrier_Index: Recommended carrier index for scan at each neighboring ABS.

Carrier index at serving ABS: Recommended logical carrier index to be used for scanning
15.2.9.2.9.2.3.1 AAI_SCN-RSP
The AAI_SCN-RSP message may include the following parameters:

N_Recommended_Carrier_Index: Number of carriers to be scanned at each neighboring ABS.

Recommended_Carrier_Index: Recommended carrier index for scan at each neighboring ABS.

Carrier index at serving ABS: Recommended logical carrier index to be used for scanning
15.2.9.2.9.2.3.1 AAI_SCN-REP
The AAI_SCN-RSP message may include the following parameters:

Scanning report of each recommended carrier at each neighboring ABS
15.2.9.2.9.2.3.1 AAI_HO-IND
The AAI_HO-IND message may include the following parameters:

Physical_Carrier_Index: Physical carrier index of the Target ABS where AMS will perform network
reentry procedure.
15.2.9.2.9.2.3.2 AAI_HO-REQ
The AAI_HO-REQ message shall include the following parameters:

Multi-Carrier_Support: If Multi-Carrier_Support is set to 0, the AMS only supports single-carrier handover
procedure defined in 15.2.6.3 and will disconnect all its active secondary carriers before handover;
otherwise, the AMS supports the multi-carrier handover procedure defined in section 15.2.9.2.9.2. no
matter the AMS which is capable of multi-carrier operation is in single-carrier mode or multi-carrier mode
For Multi-Carrier_Support = 1, the AAI_HO-REQ message may also include the following parameters:

Carrier_Preassignment_Indication: indicates whether AMS needs pre-assignment of secondary carriers at
the Target ABS
15.2.9.2.9.2.3.3 AAI_HO-CMD
The AAI_HO-CMD message shall include the following parameters:

Multi-Carrier_Indication: If Multi-Carrier_Indication is 0, the AMS shall disconnect all its active
secondary carriers and perform single-carrier handover procedure per 15.2.6.3; otherwise it performs multicarrier handover procedure per 15.2.9.2.9.2.
1
4
IEEE C802.16m -09/1283r2
For Multi-Carrier Indication = 1, the AAI_HO-REQ message also includes the following parameters:

N_Preassigned_Carriers: Number of pre-assigned secondary carriers. A value of 0 means no secondary is
pre-assigned.

Carrier_information of each pre-assigned secondary carrier if N_Preassigned_Carriers > 0. In this case, the
AAI_HO-CMD further include the following information:

1-bit carrier status indicating whether this pre-assigned carrier will be activated immediately after HO
procedure is done.

Logical carrier index is assigned implicitly in the order of Carrier_information of each pre-assigned
secondary carriers.

Physical carrier index of pre-assigned secondary carriers
15.2.9.2.9.3 Multi-carrier Zone Switch
The AMS with multi-carrier capability follows the Zone Switch procedure per section 15.2.6.4.1 except
specified in this section.
When AMS performs Zone Switch from LZone to MZone during network re-entry to LZone, the ABS sends a
RNG-RSP message with Zone Switch TLV in LZone including MZone’s multi-carrier configuration information,
as shown in Figure xxx. When an AMS performs Zone Switch from LZone to MZone after network re-entry to
LZone, the ABS sends a RNG-RSP message with Zone Switch TLV including MZone’s multi-carrier
configuration information, as shown in Figure yyy. In this case, the AMS may use another different radio carrier
to access the MZone while maintaining data transmission with LZone.
1
5
IEEE C802.16m -09/1283r2
ABS
AMS
LZone
MZone
RNG-REQ
RNG-RSP (with Zone Switch TLV
including multi-carrier configuration)
Synchronization with MZone
AAI_RNG-REQ
(Ranging Purpose Indication = Zone Switch)
AAI_RNG-RSP
Data path established
Target
carrier
1
Target
carrier
2
Figure xxx
ABS
AMS
LZone
MZone
RNG-REQ
RNG-RSP
Data path established
RNG-RSP (with Zone Switch TLV
including multi-carrier configuration)
Synchronization with MZone
AAI_RNG-REQ
(Ranging Purpose Indication = Zone Switch)
AAI_RNG-RSP
Data path established
Data path established
Radio Radio
carrier carrier
1
2
Target Target
primary secondary
carrier carrier
Figure yyy
1
6
IEEE C802.16m -09/1283r2
For AMS with multi-carrier capability performing Zone Switch from MZone to LZone, the information of
LZone (such as LZone’s carrier information) for Zone Switch shall be received through its primary carrier in
MZone. The AMS may use another different radio carrier to access the Lzone while maintaining data
transmission with Mzone.
15.2.9.2.10 Power Management
The AMS is only assigned to one or more secondary carrier during the active/normal mode. Therefore, the
power saving procedures in OFDMA multi-carrier mode of operation are the same as single carrier mode and all
messaging including idle mode procedures and state transitions are handled by the primary carrier.
15.2.9.2.10.1 Sleep mode
When an AMS enters sleep mode, the AMS negotiates its sleep mode parameters (i.e., Ssleep Wwindow and
Llistening Wwindow configuration) with an ABS. The negotiated parameters of sleep mode are applied to an
AMS and all carriers power down according to the negotiated sleep mode parameters. The messages and
procedures before entering sleep mode and during sleep mode are processed over the primary carrier. Note that
the serving ABS may request AMS to change its primary carrier upon entering the sleep mode or during the
Llistening Wwindow using carrier management MAC message for load balancing, power saving, or alleviating
signaling overhead..
During the Llistening Wwindow, the traffic indication enabled AMS monitors the traffic indication message
with its primary carrier. Upon receiving negative traffic indication in the traffic indication message, the AMS
goes back to sleep mode. If positive traffic indication is received, the AMS continues to monitor receive any DL
data the primary active carriers. If the traffic indication is disabled, dData transmission allocation and follows
the normal operation for multi-carrier mode during the Listening Window. In this case, the ABS may allocate
the DL data on the active secondary carrier and the AMS receives the data on the active secondary carrier during
the Listening Window.
15.2.9.2.10.2 Idle mode
A multi-carrier supporting AMS in idle state follows the same procedures defined in 10.5.2[3].
15.2.9.2.11 Carrier management
15.2.9.2.11.1 Secondary Carrier management
[Based on AMS’s multicarrier capabilities, the ABS may assign one or more carriers from its available carriers
to an AMS as Assigned secondary carriers through AMAC message. This message refers to carriers using their
physical carrier index and each assigned carrier is given implicitly or explicitly a logical carrier index.
The AMS does not start PHY/MAC processing of secondary carriers until directed byABS. ]
The activation or deactivation of secondary carrier(s) is decided by ABS based on QoS requirement, load
1
7
IEEE C802.16m -09/1283r2
condition of carriers and other factors. The ABS may transmit the list of active carriers to the AMS as a QoS
parameter. ABS activates and/or deactivates secondary carrier with AAI-CM-CMD MAC management message.
Carrier management MAC message The ABS sends the AAI-CM-CMD MAC management message is
transmitted on the primary carrier and shall includes the following information:

Indication Type per DL/UL: (including activationActivation, dDeactivation)

List of Secondary Carriers: (referred by logical carrier index)

Ranging indicator for the activated carrier
AAI-CM-CMD MAC management message may allocate feedback channel for the activated carriers which does
not have the paired UL like partially configured carrier or asymmetrically activated DL carrier.
In response to the AAI-CM-CMD MAC management message, AMS transmits AAI-CM-IND MAC
management message through the primary carrier. This message confirms with the ABS that the AMS has
successfully activated/deactivated the carriers listed in the AAI-CM-CMD message. In case of activation, the
confirmation is sent by the AMS when DL/UL of the newly activated carrier is ready.
After ABS receives AAI-CM-IND MAC management message ABS may start transmitting data on such active
secondary carrier(s).
Note that the AAI_CM-CMD and AAI_CM-IND message cannot be sent until the secondary carrier and the
corresponding logical carrier index are assigned to AMS.
15.2.9.2.11.2 Primary Carrier Change
The ABS may instruct the AMS, through AAI-CM-CMD MAC management message control signaling on the
current primary carrier, to change its primary carrier to one of the available assigned fully configured carriers
within the same ABS for load balancing purpose, carriers’ varying channel quality or other reasons. When an
AMS receives the AAI-CM-CMD MAC management message, the AMS transmits AAI-CM-IND MAC
management message and AMS switches to the target fully configured carrier at action time specified by the
ABS. The carrier change may also be requested by the AMS through control signaling on the current primary
carrier. Given that a common MAC manages both serving and target primary carriers, network re-entry
procedures at the target primary carrier is not required. ABS may provide the system information of the target
primary carrier that is different from the serving primary carrier via the serving primary carrier. The logical
carrier indices of the serving and target primary carrier are swapped after the primary carrier change. may be rearranged if needed. ABS may direct an AMS to change the primary carrier without scanning.
The ABS may instruct AMS to perform scanning on other carriers which are not serving the AMS. AMS reports
the scanning results back to the serving ABS, which may be used by the ABS to determine the carrier for the
AMS to switch to. In this case, if the target carrier is not currently serving the AMS, the AMS may perform
synchronization with the target carrier if required.
AAI-CM-CMD MAC management message for the primary carrier change is transmitted on the primary carrier
and shall include the following information

Target primary carrier index

Indication of the next state of serving primary carrier
1
8
IEEE C802.16m -09/1283r2

Action Time
The serving primary carrier will be kept active or deactivated depending on the indication of the next state of
serving primary carrier.
15.2.9.2.11.3 Carrier switching mode
Primary to secondary carrier switching in multi-carrier mode is supported when secondary carrier is partially
configured. The carrier switching between a primary carrier and a secondary carrier can be periodic or eventtriggered with timing parameters defined by AAI-CM-CMD MAC management message multi-carrier switching
message on the primary carrier. When an AMS switches to a secondary carrier, its primary carrier may provide
basic information such as timing and frequency adjustment to help with AMS’s with fast synchronization with
the secondary carrier. When an AMS receives the AAI-CM-CMD MAC management message, the AMS
transmits AAI-CM-IND MAC management message and switches to the secondary carrier as directed in AAICM-CMD MAC management message.
AAI-CM-CMD MAC management message for carrier switching mode is transmitted on the primary carrier and
shall include the following information

Target partially configured carriers

Switching Mode : periodic or event-triggered

Start Time

Switching Interval

Switching Period (if it is periodic switching mode)
15.2.9.2.11.4 MAC Management Messages for Carrier Management
15.2.9.2.11.4.1 AAI Carrier Management Command MAC management message : AAI-CM-CMD
Field
Size (bit)
Description
Management Message Type
8
AAI_CM-CMD
Action code
2
00: Secondary Carrier Management
AAI_Carrier Management Command message
format(){
01: Primary carrier change
10: Carrier switching
11: reserved
1
9
IEEE C802.16m -09/1283r2
This message is for secondary carrier activation
and/or deactivation
If (Action code == 00){
Indication Type
2
For Activation and/or Deactivation
Bit #0: ‘0’: No action, ‘1’: Activation
Bit #1: ‘0’: No action, ‘1’: Deactivation
If (Indication Type #0 == 1)
Num of target carrier
[TBD]
The number of newly activated carrier(s)
Target carrier index
[TBD]
Target carrier index for activation
Activation of DL/UL
1
‘0’: Both DL/UL are activated
For(i=0; i< Num of target carrier; i++){
‘1’: DL is activated but UL is not activated
Ranging indicator
1
Ranging indicator for target carrier
‘0’: No ranging is required for the target carrier
‘1’: Periodic ranging is required for the target
carrier
}
}
If (Indication Type #1 == 1){
Num of target carrier
[TBD]
The number of deactivated carrier(s)
Target carrier index
[TBD]
Target carrier index for deactivation
Deactivation of DL/UL
1
‘0’: Both DL/UL are deactivated
For(i=0; i< Num of target carrier; i++){
‘1’: UL is deactivated but DL is kept active
}
}
}
If (Action code == 01){
This message is for primary carrier change.
Target carrier index
[TBD]
Target carrier index for primary carrier change
Next state of serving primary carrier
1
‘0’: Serving carrier will be deactivated after
primary carrier change
‘1’: Serving carrier is kept active after primary
carrier change
}
If (Action code == 10){
This message is for secondary carrier switching.
2
0
Target carrier index
[TBD]
IEEE C802.16m -09/1283r2
Target carrier index for carrier switching
Switching Mode
1
Periodic or event-triggered switching
0: Periodic switching
1: Event-triggered switching
Start Time
[TBD]
TBD LSB bits of Superframe number at the start
time of carrier switching
Switching Interval
[TBD]
Number of superframes during which an AMS
stays at the target secondary carrier before
returning to the primary carrier
[TBD]
Number of superframes between consecutive
switching interval
If (Switching Mode == 0){
Switching Period
}
}
}
15.2.9.2.11.4.2 AAI Carrier Management Indication MAC management message : AAI-CM-IND
Field
Size
Description
Management
Message Type
8
//AAI_CM-IND
Action code
2
00: Secondary carrier management
AAI_Carrier
Management Indication
messge format(){
01: Primary carrier change
10: Carrier switching
11: reserved
}
-------------------------------------------------------------End of the Text--------------------------------------------------------
2
1