Page 1 of 30
Document #
LAT-PS-05664-05
Date
11/18/05
Author(s):
A. T. Kavelaars
GLAST LAT
Subsystem/Office
Integration and Test Subsystem
Document Title
GLAST LAT I&T E-Logbook Test Procedure and Report
Gamma-ray Large Area Space Telescope (GLAST)
Large Area Telescope (LAT)
I&T E-Logbook Test Procedure and Report
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 2 of 30
Change History Log
Revision
Effective Date
Description of Changes
01
01/26/05
Initial Release
02
03/25/05
Revised Setup Instructions
Added line to enter attachment # for scripts versions
Revised Test Cases 7.3.4 to 7.3.10
03
05/12/05
Re-indexed Setup Validation to 7.1.4
Added: JIRA Issue attachment placeholder as part 7.2.
Added: 7.3.5.2.4) e)
Modified: 7.1.3, 7.3.3.2.4) b), 7.3.6.2.5) a)
No longer TBX: 7.3.1.2.2) e), 7.3.4.2.8) c), 7.3.6.2.3) c),
7.3.6.2.4) d), 7.3.8.2.5) a), 7.3.9.2.3) a), 7.3.10.2.3) a)
Put appendix A as part 8. Re-indexed document accordingly.
04
6/20/05
Added General Instructions Section.
Changed Setup Instructions.
Added attachment space for Print statements in Sections: 7.3.2.2. 5),
7.3.3.2. 7), 7.3.4.2. 10), 7.3.5.2. 6), 7.3.6.2. 6), 7.3.7.2. 4), 7.3.8.2.
6), 7.3.9.2. 4), 7.3.10.2. 3).
Added FHW LAT Matrix Log: Section 7.3.11.1
Added: 7.3.3.2. 6), 7.3.4.2. 3), 7.3.4.2. 9), 7.3.4.2. 8), 7.3.5.2. 3),
7.3.6.2. 3), 7.3.9.2. 3).
Modified: 7.3.3.2. 6), 7.3.4.2. 2), 7.3.4.2. 9), 7.3.9.2. 2), 7.3.9.2. 3).
Re-indexed document accordingly.
05
11/19/05
Added setup instructions for Linux in 7.1.3.
Added 7.3.1.2. 2) h), 3) and 4), 7.3.5.2. 5) h)
Modified 7.3.5.2. 5) and 5) e).
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 3 of 30
Contents
1.
PURPOSE .................................................................................................................................. 5
2.
SCOPE ....................................................................................................................................... 5
3.
ACRONYMS / DEFINITIONS ............................................................................................... 5
3.1.
Acronyms ............................................................................................................................................................. 5
3.2.
Definitions............................................................................................................................................................ 6
3.2.1.
E-Logbook: ............................................................................................................................................... 6
3.2.2.
MySQL elogbook ..................................................................................................................................... 6
4.
APPLICABLE DOCUMENTS ................................................................................................ 6
5.
DESCRIPTION ......................................................................................................................... 6
6.
REQUIREMENTS .................................................................................................................... 6
6.1.
7.
GENERAL INSTRUCTIONS ........................................................................................................................... 7
TEST PROCEDURE ................................................................................................................ 7
7.1.
SETUP ................................................................................................................................................................. 7
7.1.1.
Hardware Setup......................................................................................................................................... 7
7.1.2.
Software Setup & Test Environment ........................................................................................................ 7
7.1.2.1.
E-Logbook Scripts ................................................................................................................................ 8
7.1.3.
Setup Instructions ..................................................................................................................................... 8
7.1.3.1.
Install E-Logbook for remote database access ...................................................................................... 8
7.1.3.2.
Create a local copy of the E-Logbook Database ................................................................................... 9
7.1.4.
Setup Validation ..................................................................................................................................... 12
7.2.
JIRA ISSUES .................................................................................................................................................... 12
7.3.
TEST CASES .................................................................................................................................................... 12
7.3.1.
Test Case: E-Logbook Main ................................................................................................................... 12
7.3.1.1.
Test Objective ..................................................................................................................................... 12
7.3.1.2.
Test Procedure .................................................................................................................................... 12
7.3.1.3.
Overall Outcome of Test Case 7.3.1 ................................................................................................... 13
7.3.2.
Test Case: User Log ................................................................................................................................ 14
7.3.2.1.
Test Objective ..................................................................................................................................... 14
7.3.2.2.
Test Procedure .................................................................................................................................... 14
7.3.2.3.
Overall Outcome of Test 7.3.2 ............................................................................................................ 14
7.3.3.
Test Case: Shift Log ............................................................................................................................... 15
7.3.3.1.
Test Objective ..................................................................................................................................... 15
7.3.3.2.
Test Procedure .................................................................................................................................... 15
7.3.3.3.
Overall Outcome of Test 7.3.3 ............................................................................................................ 16
7.3.4.
Test Case: EGSE Log ............................................................................................................................. 16
7.3.4.1.
Test Objective ..................................................................................................................................... 16
7.3.4.2.
Test Procedure .................................................................................................................................... 16
7.3.4.3.
Overall Outcome of Test 7.3.4 ............................................................................................................ 18
7.3.5.
Test Case: Mate/Demate ......................................................................................................................... 19
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
7.3.5.1.
7.3.5.2.
7.3.5.3.
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 4 of 30
Test Objective ..................................................................................................................................... 19
Test Procedure .................................................................................................................................... 19
Overall Outcome of Test Case 7.3.5 ................................................................................................... 20
7.3.6.
Test Case: Flight Hardware Installation Log .......................................................................................... 20
7.3.6.1.
Test Objective ..................................................................................................................................... 20
7.3.6.2.
Test Procedure .................................................................................................................................... 20
7.3.6.3.
Overall Outcome of Test 7.3.6 ............................................................................................................ 21
7.3.7.
Test Case: Material Mix Record ............................................................................................................. 22
7.3.7.1.
Test Objective ..................................................................................................................................... 22
7.3.7.2.
Test Procedure .................................................................................................................................... 22
7.3.7.3.
Overall Outcome of Test Case 7.3.7 ................................................................................................... 22
7.3.8.
Test Case: Flight Software Installation Log............................................................................................ 23
7.3.8.1.
Test Objective ..................................................................................................................................... 23
7.3.8.2.
Test Procedure .................................................................................................................................... 23
7.3.8.3.
Overall Outcome of Test 7.3.8 ............................................................................................................ 24
7.3.9.
Test Case: Configuration Log ................................................................................................................. 24
7.3.9.1.
Test Objective ..................................................................................................................................... 24
7.3.9.2.
Test Procedure .................................................................................................................................... 24
7.3.9.3.
Overall Outcome of Test Case 7.3.9 ................................................................................................... 25
7.3.10.
Test Case: Configuration Request Log ................................................................................................... 25
7.3.10.1.
Test Objective ..................................................................................................................................... 26
7.3.10.2.
Test Procedure .................................................................................................................................... 26
7.3.10.3.
Overall Outcome of Test Case 7.3.10 ................................................................................................. 26
7.3.11.
Test Case: Data Reporting Tools ............................................................................................................ 26
7.3.11.1.
Flight Hardware LAT Matrix Log ...................................................................................................... 26
7.3.11.1.1. Test Objective ................................................................................................................................... 26
7.3.11.1.2. Test Procedure................................................................................................................................... 27
7.3.11.1.3. Overall Outcome of Test Case 7.3.11.1 ............................................................................................ 27
7.3.12.
Test Case: Database Performance Tool (TBX) ....................................................................................... 27
8.
DEVIATIONS FROM THE QUALIFICATION TEST PROCEDURE ........................... 28
9.
CERTIFICATION .................................................................................................................. 30
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
1.
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 5 of 30
PURPOSE
The purpose of this document is to define the Test Procedure and Report for E-Logbook, the
Integration and Test electronic database for the Large Area Telescope (LAT).
2.
SCOPE
This document defines the test procedure and report for E-Logbook, based on the requirements
defined at LAT-MD-04601. A Verification and Validation Matrix is defined with the
correspondence of the requirements to tests. A test is required every time there is a new release of ELogbook. This document will be signed off every time a run for the record for a new version is
carried out. The new version is approved via CCB. The results will be scanned in and saved
accordingly.
3.
ACRONYMS / DEFINITIONS
3.1. ACRONYMS
LAT
Large Area Telescope
GSE
Ground Support Equipment
GLAST
Gamma-ray Large Area space Telescope
I&T
Integration and Test
MGSE
Mechanical Ground Support Equipment
EGSE
Electrical Ground Support Equipment
SVAC
Science Verification, Analysis, and Calibration
GUI
Graphic User Interface
ISOC
Instrument Science Operations Center
QA
Quality Assurance
IRR
Integration Readiness Review
TRR
Test Readiness Review
AIDS
Assembly Instruction Data Sheet
IFCT
Integration, Facilities, Configuration, and Test
NCR
Non-Conformance Report
CM
Configuration Management
LAN
Local Area Network
PAIP
Performance Assurance Implementation Plan
OSHA
Occupational Safety and Health Act
ES&H
Environmental Safety and Health
ESD
Electro-Static Discharge
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
R/D
GLAST LAT I&T E-Logbook Test Procedure and Report
Reference Designator
FHW
Flight Hardware
FSW
Flight Software
MMR
Material Mix Record
Page 6 of 30
3.2. DEFINITIONS
3.2.1. E-Logbook:
Graphical User Interface to enter and retrieve data that captures all the critical activities performed in
the GLAST LAT I&T facility. E-Logbook is designed to optimize the data input and speed of data
retrieval.
3.2.2. MySQL elogbook
Electronic database structure written in MySQL that holds the data created via E-Logbook.
4.
5.
APPLICABLE DOCUMENTS
LAT-MD-00408
LAT Instrument Performance Verification Plan.
LAT-MD-01386
LAT Facilities Plan
LAT-MD-02730
Performance and Operations Test Plan
LAT-MD-03492
I&T Configuration Management plan
LAT-MD-01376
LAT I&T Plan
LAT-MD-04601
GLAST LAT I&T E-Logbook Implementation Plan
DESCRIPTION
Every time there is a new E-Logbook release a test conductor will follow this document to test each
component of this product. QA will be necessary to sign off the release, as is captured in the test
report part of the procedure.
6.
REQUIREMENTS
E-Logbook requirements defined at LAT-MD-04601 will be satisfied following the Verification and
Validation Matrix. Once a test case defined in section 7.2 of this document is completed, a check
mark will be entered in the last column of the matrix.
V&V TEST MATRIX
REQ # NAME/DESCRIPTION
Main
COMPONENT
TEST ID
E-Logbook Main
7.3.1
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
VERIFIED
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
6.1.1.1
User Log
User Log
7.3.2
6.1.2.1
Shift Log
Shift Log
7.3.3
6.1.3.1
EGSE Log
EGSE Log
7.3.4
6.1.4.1
Mate/Demate
Mate/Demate Log
7.3.5
6.1.5.1
Hardware Component Installation
Hardware Component Installation Log
7.3.6
6.1.6.1
Material Mix Record
Material Mix Record Log
7.3.7
6.1.7.1
Flight Software Installation
Flight Software Installation Log
7.3.8
6.1.8.1
Configuration Log
Configuration Log
7.3.9
6.1.9.1
Configuration Report
Configuration Report
7.3.10
6.2.1.1
Data Reporting
Analysis Tools
7.3.11
6.2.2.1
Database Performance
Analysis Tools
7.3.12 (TBX)
Page 7 of 30
6.1. GENERAL INSTRUCTIONS
This qualification test procedure shall be conducted on a formal basis to its latest approved and
released version. The designated Software QAE shall be notified 24 hours prior to the start of this
procedure. Software QAE may monitor the execution of all or part of this procedure should they
elect to do so.
The Test Engineer conducting this test shall read this document in its entirety and resolve any
apparent ambiguities before beginning the procedures described herein.
Deviations from the procedures described in this document and breaks in hardware or software
configuration can only be initiated by the Test Engineer, must be approved by QA, and must be
documented in Section 8. The program can be restarted any time during testing without incurring
into breaking configuration.
Any nonconformance/defect/anomaly is to be reported in JIRA and/or Section 8. Do not alter or
break configuration if a failure occurs. Notify Software Quality Assurance. All success conditions
for a test must be met for the test to pass.
7.
TEST PROCEDURE
7.1. SETUP
7.1.1. Hardware Setup
A Windows based PC is the only hardware necessary to test E-Logbook.
7.1.2. Software Setup & Test Environment
The software listed in the Test Environment table with the indicated versions must be installed in the
machine. The version for E-Logbook will be entered at the time of test and retrieved from the CVS
tagging system, for example P03-02-00 means E-Logbook version 3.2.0.
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 8 of 30
Important: All tests will verify data entry with known values for known fields via the MySQL
Control Center GUI.
TEST ENVIRONMENT
COMPONENT VERSION LOCATION
LICENSE
E-Logbook
http://wwwglast.slac.stanford.edu/IntegrationTest/
ONLINE/ELogbook/download.htm
SLAC Copyright
Win OS
www.microsoft.com
As indicated on website
MySQL
4.1.7
www.mysql.org
As indicated on website
Qt
3.3.3
www.trolltech.com
Yes
Python
2.3.5
www.python.org
As indicated on website
PyQt
3.0.9
www.riverbankcomputing.co.uk/pyqt
As indicated on website
7.1.2.1.
E-Logbook Scripts
E-Logbook with version detailed in the Test Environment Table is comprised of the tests scripts
listed in the following attachment:
_________________________________________________________________________________
7.1.3. Setup Instructions
E-Logbook test setup involves mainly software. Please make sure that all of the following steps have
been completed before a test run is performed:
7.1.3.1.
Install E-Logbook for remote database access
Note: This can only be used to read data

Make sure the following software is installed in your machine:
E-LOGBOOK ENVIRONMENT
COMPONENT
VERSION
LOCATION
E-Logbook
Latest
MySQL
4.1.7
www.mysql.org
As indicated on website
Python
2.3.5
www.python.org
As indicated on website
http://wwwglast.slac.stanford.edu/IntegrationTest/ON
LINE/ELogbook/download.htm
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LICENSE
SLAC Copyright
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 9 of 30
Unix Environment Additional Packages:
COMPONENT
VERSION
LOCATION
LICENSE
Qt
3.3.3
www.trolltech.com
PyQt
3.14.1
http://www.riverbankcomputing.co.uk/py As indicated on website
qt/index.php
Sip
4.3.2
http://www.riverbankcomputing.co.uk/si
p/index.php
As indicated on website
Doxygen
1.4.5
http://www.stack.nl/~dimitri/doxygen/
As indicated on website
As indicated on website
In Windows:

Add C:\Python23\ to PATH.

Add C:\Program Files\MySQL\MySQL Server 4.1\bin to PATH.
To Launch E-Logbook: If there is a shortcut in the desktop double click on it. Otherwise open a
Command Prompt (Windows) or Shell (Unix) and enter:

In Windows:
o \\Elogbook\start\startElogbook.bat

In Unix:
o //ELogbook/start/startElogbook.csh
 Once the Connect window appears select glast03 as hostname for access to a mirror copy of
the cleanroom E-Logbook database.
7.1.3.2.

Create a local copy of the E-Logbook Database
Make sure the following software is installed in your machine:
E-LOGBOOK ENVIRONMENT
COMPONENT
VERSION
LOCATION
LICENSE
E-Logbook
Latest
http://wwwSLAC Copyright
glast.slac.stanford.edu/IntegrationTest/
ONLINE/ELogbook/download.htm
MySQL
4.1.7
www.mysql.org
As indicated on website
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
MySQL
Center
GLAST LAT I&T E-Logbook Test Procedure and Report
Control 0.9.4
Python
2.3.5
Page 10 of 30
www.mysql.org
As indicated on website
www.python.org
As indicated on website
Unix Environment Additional Packages:
COMPONENT
VERSION
LOCATION
LICENSE
Qt
3.3.3
www.trolltech.com
PyQt
3.14.1
http://www.riverbankcomputing.co.uk/py As indicated on website
qt/index.php
Sip
4.3.2
http://www.riverbankcomputing.co.uk/si
p/index.php
As indicated on website
Doxygen
1.4.5
http://www.stack.nl/~dimitri/doxygen/
As indicated on website
As indicated on website
In Windows:

Add C:\Python23\ to PATH.

Add C:\Program Files\MySQL\MySQL Server 4.1\bin to PATH.

Environment variable setup:
o For E-Logbook up to and including version 3.3.0: Create environment variable
ONLINE_ROOT pointing to the parent directory where E-Logbook has been
installed, for example C:\LAT\Online.
o For E-Logbook version 3.4.0 and on: Create environment variable TOOLS_ROOT
pointing to the parent directory where E-Logbook has been installed, for example
C:\LAT\Tools.
Database Setup (Both Windows and Unix):

Open the MySQL Control Center GUI:
o Right click User Administration and select New User:

Select Global Privileges:

Under Username enter: root

Under Host enter: localhost

Under Password enter: A password of your choice
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05

GLAST LAT I&T E-Logbook Test Procedure and Report
Page 11 of 30
Open up a Command Prompt and enter the following:
1) mysql –u root –p –e "drop database elogbook"
(Ignore the error)
o You will have to enter the password you created for root in the MySQL Control
Center for steps 1) to 3).
2) mysql –u root –p -e "create database elogbook"
3) mysql –u root –p elogbook < \\X.sql
or
mysql –u root –p elogbook < \\Y.dmp
o X indicates an empty copy of the release version you are about to test.
o Y indicates a backup copy of the cleanroom database you are about to review.

At the MySQL Control Center GUI:
o Under New User:

Select ELogbook.

Under Username enter: Elogbook

Under Host enter: localhost

Under Password enter: Elogbook
o MySQL CCC will help you verify data entry and retrieval during the test.

In the Command Prompt (it can be the same as above) go to \\Elogbook\start\ and enter:
startElogbook

(launches E-Logbook).
If the connect window complains that it cannot open the elogbook database on localhost:
o In Windows:
o

Make sure the MySQL Service located at ControlPanel-> Administrative
tools -> Services has started (press the play button otherwise).

Copy libMySQL.dll located at c:\Program Files\MySQL\MySQL Server
4.1\bin under the folder \\ELogbook\ext.
In Unix:

Make sure the MySQL server has started by typing:

/etc/init.d/mysqld start
To Launch E-Logbook: If there is a shortcut in the desktop double click on it. Otherwise open a
Command Prompt (Windows) or Shell (Unix) and enter:

In Windows:
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 12 of 30
o \\Elogbook\start\startElogbook.bat

In Unix:
o //ELogbook/start/startElogbook.csh
 Once the Connect window appears select localhost as hostname for access to the local copy
of E-Logbook just created following the steps above.
7.1.4. Setup Validation
Before the tests begin, the Test Engineer and Quality Assurance Engineer verify the version numbers
of all software listed in the table in Section 7.1.2 and initial below.
__________________ _____________ ________________ ______________
Date
Time
Test Engineer
QAE
7.2. JIRA ISSUES
E-Logbook with version detailed in the Test Environment Table addresses the JIRA issues listed in
the following attachment:
_________________________________________________________________________________
7.3. TEST CASES
The following tests are designed to invoke components of a graphical user interface. Successful
result of the test involves that data was recorded and retrieved successfully in the E-Logbook
database via the graphic user interface. A list of the underlying scripts being tested by each test case
will be provided at the beginning of each case.
7.3.1. Test Case: E-Logbook Main
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.1 corresponding to Test Case: E-Logbook Main.
7.3.1.1.
Test Objective
Verify that E-Logbook launches and connects to MySQL elogbook to retrieve data.
7.3.1.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
2) Launch E-Logbook:
Page 13 of 30
a) Display known MySQL elogbook data in the main window with no reported error messages.
In particular:
b) Shift Log has current Shift and Date selected in the list boxes.
c) Mate/Demate Connector List displays known values.
d) Hardware Component List displays known values.
e) Flight Software Component List displays known values.
f) EGSE List displays known values.
g) MMR List displays known values.
h) Done button closes E-Logbook (all windows open).
i) Hide Savers check box hides savers in M/D Log list.
3) Test duplicate and removal of components:
a) Right click Duplicate on a component description of each list (Mate/Demate, FHW, FSW
and EGSE). Check that a duplicate component with a new name and the same R/D list is
created. Make sure that, for each RD, if it is already in the database then it is not duplicated
and an information message appears.
b) Right click Removal on a component description of each list (Mate/Demate, FHW, FSW and
EGSE). Check that the component description and its R/D list is removed. Make sure that,
for each RD, if it has already been used in the database then the removal is not permitted an
information message appears.
4) Main Preferences:
a) From Preferences Menu:
i) Select Font and Style.
ii) Close and verify Font and Style selection.
b) Resize Main window.
c) Restart E-Logbook and verify size.
7.3.1.3.
Overall Outcome of Test Case 7.3.1
Based on the analysis of the test results, the overall outcome of Test 7.3.1 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 14 of 30
7.3.2. Test Case: User Log
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.2 corresponding to Test Case: User Log.
7.3.2.1.
Test Objective
Verify that E-Logbook creates and retrieves the list of E-Logbook users.
7.3.2.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) Under Elogbook Main click add user and retrieve list of known users with known values.
3) Add a New User:
a) Created known new user with known values.
b) Displayed new user in user list
4) Update a User:
a) Updated known user record with known values.
b) Displayed updated user with known values.
5) General Considerations
a) Attach print copy of User Log showing the addition and change:
_________________________________________________________________________________
7.3.2.3.
Overall Outcome of Test 7.3.2
Based on the analysis of the test results, the overall outcome of Test 7.3.2 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 15 of 30
7.3.3. Test Case: Shift Log
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.3 corresponding to Test Case: E-Logbook Main.
7.3.3.1.
Test Objective
Verify that E-Logbook creates, retrieves and prints Flight Software Installation Records filtered by
Component Description and R/D.
7.3.3.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) Shift Summary
a) Created a known summary with known values..
3) Shifters Sign In
a) Created a known shifter record with known values
4) Activity Tables
a) Created a known Activity, Problem and Other record with known values, for different
subsystems.
b) Retrieved known record with known values in read only format, web link enabled.
5) List of Runs
a) Displayed known run records with known information.
b) Displayed known run report for selected run.
6) Shift Log Default Startup Tool in Preferences Menu:
a) Select Default subsystem for shift log startup.
b) Verify selection in Shift Log.
c) Close Shift Log.
d) Restart Shift Log and verify selection.
7) General Considerations
a) The shift toggle buttons (Prev., Next and Refresh) load information on adjacent shifts
properly.
b) Attach print copy of Activity Report with known values:
_________________________________________________________________________________
c) Attach print copy of Shift Log with known values:
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 16 of 30
_________________________________________________________________________________
7.3.3.3.
Overall Outcome of Test 7.3.3
Based on the analysis of the test results, the overall outcome of Test 7.3.3 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
7.3.4. Test Case: EGSE Log
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.4 corresponding to Test Case: EGSE Log.
7.3.4.1.
Test Objective
Verify that E-Logbook creates, retrieves and prints EGSE Records filtered by EGSE Description and
Assembly Number. Verify that records can be populated with EGSE Components. Verify that
records can be revalidated.
7.3.4.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) New EGSE
a) Under the Main window create known EGSE record with known values.
b) New Record displays in EGSE list:
i) If Unit already existed new EGSE Assembly Number/Location is listed below it.
ii) If a new Unit has been entered it is properly displayed as a main item of the list, with the
Assembly Number listed as a sub item.
iii) If cancel, esc or the X button is clicked in the New EGSE window, no new EGSE data is
saved or displayed in the connector list on the main window.
3) Edit EGSE
a) Under the Main window edit known EGSE record with known values.
b) QA approval is entered for the changes to be saved.
c) Updated Record displays in EGSE list:
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 17 of 30
i) If Unit already existed the new EGSE Assembly Number/Location is listed below it.
ii) If a new Unit Description has been entered, it is properly displayed as a new main item of
the list, with the Assembly Number listed as a sub item. It will no longer be listed in the
old Unit Description.
iii) If cancel, esc or the X button is clicked in the New EGSE window, no new EGSE data is
saved or displayed in the connector list on the main window.
4) Assign EGSE
a) Create known EGSE Validation Record with known values, select the correct EGSE type.
b) Create EGSE Component Records with correct type corresponding to the EGSE type. For
example EGSE SW Component for EGSE Type WORKSTATION or SERVER.
c) Invoking save EGSE Validation Record in Assign EGSE Validation record created known
EGSE Validation Record with known values.
d) Invoking add comment in Assign EGSE created known comment with known values.
5) EGSE Component
a) Invoking add EGSE Validation Record Component in Assign EGSE Validation record
created known EGSE Validation Component Record with known values, and displayed
known record in Assign EGSE under component list.
b) Check that for every component that:
i) Validation Expiration Date N/A: It is stated so.
ii) Validation Expired: The EGSE Component record is colored in red.
iii) Validation will expire within a month: The EGSE Component record is colored in
orange.
iv) Removed: The EGSE Component record is colored green, and its validation expiration
date if available has not been taken into account to determine the overall EGSE Record
expiration.
6) Validation Date
a) If an EGSE Component has a validation expiration date, check the EGSE Record has been
updated to take into account earliest validation expiration date: that will be the overall
validation expiration date of the EGSE Record.
b) Check that if validation expiration date is:
i) Expired: EGSE Record is colored in red.
ii) Will expire within a month: EGSE Record is colored in orange.
7) Revalidate a EGSE Record
a) To revalidate an EGSE Record that has expired or is about to expire select it from EGSE
Report to access the Assign EGSE window. Click on revalidate.
b) In order to edit a component of the EGSE Component list double click on the component.
i) In the Assign EGSE Component window click on revalidate or remove.
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 18 of 30
ii) Update the document, validation expiration and OP information, and Save.
c) Add New EGSE Components if necessary.
d) The global Validation Expiration Date will be updated according to the new changes.
e) Update the validation document, OP and QA information.
f) Click save, the new EGSE Validation Record will be inserted in the EGSE Report.
8) EGSE Report
a) Select an EGSE (Unit and Assembly Number).
b) Click Validate in the Main Window EGSE tab to access the EGSE Validation Report for the
selected EGSE record.
c) Check that the list with all known validation records of the selected EGSE is displayed.
i) Make sure that records are color coded as explained in 5).
d) Select EGSE Validation Record and verify it displays known values, known EGSE
Validation Record Components with known values, and known comments.
9) EGSE Default Validation Expiration Limit (Preferences Menu):
a) Select default EGSE Expiration Limit and save.
b) Verify that the EGSE Report and Validation Record get refreshed showing the new selected
limit.
10) General Considerations
a) Validation Date: Under Assign EGSE, every time a new EGSE Component is added or
removed the global Validation Date is recalculated and equal to the earliest in time EGSE
Component Validation Date.
b) Revalidate: Under Assign EGSE, the Revalidate button enables all fields to expedite the
revalidation process, creating a new known record with known values, following all the
procedure described above.
c) Attach print copy of EGSE Report with known values:
_________________________________________________________________________________
d) Attach print copy of EGSE Validation Record with known values:
_________________________________________________________________________________
7.3.4.3.
Overall Outcome of Test 7.3.4
Based on the analysis of the test results, the overall outcome of Test 7.3.4 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 19 of 30
7.3.5. Test Case: Mate/Demate
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.5 corresponding to Test Case: Mate/Demate Log.
7.3.5.1.
Test Objective
Verify that E-Logbook creates, retrieves and prints Mate/Demate records filtered by Connector
Description and R/D.
7.3.5.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) New Connector
a) Under the Main Window Mate/Demate tab click New and enter new Connector information:
i) If the unit already exists the new R/D is listed below it.
ii) If a new Unit has been entered it is properly displayed as a main item of the list, with the
R/D listed as a sub item.
iii) If cancel, esc or the X button is clicked in the New Connector window, no new connector
data is saved or displayed in the connector list on the main window.
3) Edit Connector
a) Under the Main Window Mate/Demate tab click Edit and update Connector information.
b) QA approval is entered for the changes to be saved.
c) Updated Record displays in Mate/Demate list:
i) If the updated Unit Description already exists the new R/D is listed below it.
ii) If a new Unit has been entered it is properly displayed as a main item of the list, with the
R/D listed as a sub item.
iii) If cancel, esc or the X button is clicked in the New Connector window, no new connector
data is saved or displayed in the connector list on the main window.
4) Mate/Demate Report
a) Displayed known Connector Mate/Demate Report with known values.
b) Displayed selected Connector Mate/Demate Record with known values.
c) Displayed current Connector Mate/Demate state on Add selection.
5) Assign Mate/Demate (Preform access and save Assign Mate/Demate both from Main Window
and Mate/Demate Report):
a) Created new known Mate/Demate Record for known Connector with known values.
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 20 of 30
b) Displayed message error upon selection of same Connector as second Connector.
c) Displayed message error upon selection of a currently Mated Connector as second
Connector.
d) Fixed Mate/Demate selection depending on current state of the Connector.
e) Created and displayed torque information. If N/A is checked, torque information is disabled
(only for Mates).
f) If the Connector is currently mated displayed second Connector in read only format.
g) Added known comment record with known values.
h) Hide savers check box hides connector saver information from 2nd connector list.
6) General Considerations
a) Attach print copy of M/D Report with known values:
_________________________________________________________________________________
7.3.5.3.
Overall Outcome of Test Case 7.3.5
Based on the analysis of the test results, the overall outcome of Test 7.3.5 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
7.3.6. Test Case: Flight Hardware Installation Log
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.6 corresponding to Test Case: Hardware Installation Log.
7.3.6.1.
Test Objective
Verify that E-Logbook creates, retrieves and prints FHW Installation records filtered by Component
Description and R/D.
7.3.6.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) New FHW Component
a) Under the Main Window FHW Installation tab click New and enter the new Component
information:
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
i) If the Unit already exists the new R/D is listed below it.
Page 21 of 30
ii) If a new Unit has been entered it is properly displayed as a main item of the list, with the
R/D listed as a sub item.
iii) If cancel, esc or the X button is clicked in the New FHW Component window, no new
connector data is saved or displayed in the connector list on the main window.
3) Edit FHW Component
a) Under the Main Window FHW Installation tab click New and enter the new Component
information.
b) QA approval is entered for the changes to be saved.
c) Updated Record displays in FHW Component list:
i) If the updated Unit already exists the new R/D is listed below it.
ii) If a new Unit has been entered it is properly displayed as a main item of the list, with the
R/D listed as a sub item.
iii) If cancel, esc or the X button is clicked in the New FHW Component window, no new
connector data is saved or displayed in the connector list on the main window.
4) FHW Installation Report
a) Displayed known FHW Component Installation Report with known values.
b) Displayed selected FHW Component Installation Record with known values.
c) Displayed current FHW Component Installation state on Add selection.
5) Assign FHW Installation
a) Created new known FHW Installation Record for known Component with known values,
upon selected completion state.
b) Selected known FHW Component Installation Record and added known values for new
known completion state.
c) Displayed current FHW Component Installation record activity (In Progress, Install, or
Remove).
d) Fixed known FHW Component Installation record activity upon add selection, (if removed,
allow install only, etc).
6) General Considerations
a) Units: Displayed known values in known selected weight, flatness and torque units for every
torque value listed.
b) Attach print copy of FHW Installation Report with known values:
_________________________________________________________________________________
7.3.6.3.
Overall Outcome of Test 7.3.6
Based on the analysis of the test results, the overall outcome of Test 7.3.6 is as follows:
□ Passed - all of the success conditions for the test were met.
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
□ Failed - one or more of the success conditions were not met.
__________________
Date
Page 22 of 30
________________ ______________
Test Engineer
QAE
7.3.7. Test Case: Material Mix Record
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.7 corresponding to Test Case: Material Mix Record Log.
7.3.7.1.
Test Objective
Verify that E-Logbook creates, retrieves and prints Material Mix Records filtered by MMR #.
7.3.7.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) New MMR
a) Created known MMR with known values.
b) Assigned new MMR #.
3) Update MMR
a) Displayed known MMR with known values.
b) Updated known MMR with known values.
4) General Considerations
a) Once a new MMR is generated, select it, retrieve it and review values.
b) Units: Displayed known values in known selected weight units.
c) Hardness: Displayed error if exists known discrepancy between, Minimum and Average
Hardness, and Test Result.
d) Attach print copy of MMR with known values:
_________________________________________________________________________________
7.3.7.3.
Overall Outcome of Test Case 7.3.7
Based on the analysis of the test results, the overall outcome of Test 7.3.7 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
__________________
Date
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 23 of 30
________________ ______________
Test Engineer
QAE
7.3.8. Test Case: Flight Software Installation Log.
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.8 corresponding to Test Case: Flight Software Installation Log
7.3.8.1.
Test Objective
Verify that E-Logbook creates, retrieves and prints Flight Software Installation Records filtered by
Component Description and R/D.
7.3.8.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) New FSW Component
a) Under the Main Window FSW Installation tab click New and enter the new Component
information:
i) If the Unit already exists the new R/D is listed below it.
ii) If a new Unit has been entered it is properly displayed as a main item of the list, with the
R/D listed as a sub item.
iii) If cancel, esc or the X button is clicked in the New FSW Component window, no new
connector data is saved or displayed in the connector list on the main window.
3) Edit FSW Component
a) Under the Main Window FSW Installation tab click New and enter the new Component
information.
b) QA approval is entered for the changes to be saved.
c) Updated Record displays in FSW Component list:
i) If the updated Unit already exists the new R/D is listed below it.
ii) If a new Unit has been entered it is properly displayed as a main item of the list, with the
R/D listed as a sub item.
iii) If cancel, esc or the X button is clicked in the New FSW Component window, no new
connector data is saved or displayed in the connector list on the main window.
4) FSW Installation Report
a) Displayed known FSW Component Installation Report with known values.
b) Displayed selected FSW Component Installation Record with known values.
5) Assign FSW Installation
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 24 of 30
a) Created new known FSW Installation Record for known Component with known values,
upon selected completion state.
b) Selected known FSW Component Installation Record and added known values for new
known completion state.
6) General Considerations
a) Attach print copy of FSW Report with known values:
_________________________________________________________________________________
7.3.8.3.
Overall Outcome of Test 7.3.8
Based on the analysis of the test results, the overall outcome of Test 7.3.8 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
7.3.9. Test Case: Configuration Log
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.9 corresponding to Test Case: Configuration Log
7.3.9.1.
Test Objective
Verify that E-Logbook creates, retrieves and prints Configuration Logs for the following
components: FHW Log, FSW Log and EGSE Validation Log.
A Configuration Log will display the current state of EVERY unit component for the selected type
(FHW, FSW or EGSE) at the time of configuration.
7.3.9.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) Configuration Log
a) In the Main Window FHW, FSW or EGSE tab press Configuration Log.
b) Enter username and password information that will be subsequently passed to the
Configuration Request Log (See Section 7.3.10).
c) The corresponding Configuration Log window displays a list of ALL known Component
units:
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 25 of 30
i) EGSE Validation Log: The configuration Log will show the units’ current validation
state; i.e. it displays its latest validation record color coded as described in Test Case ID
7.3.4.
(1) Verify that the EGSE units expired or about to expire validation are color coded
accordingly as described in 7.3.4.2. part 6).
(2) Verify that the Main Window EGSE tab shows the right number of EGSE units that
have expired or are about to expire validation.
d) Verify that double clicking a record accesses the corresponding record to be reviewed.
i) In the EGSE Validation Log, verify that the window that allows the record to be
revalidated.
ii) Revalidate if necessary following 7.3.4.2 part 7).
(1) Verify that if revalidated the EGSE Validation record is updated in the Configuration
Log.
3) EGSE Default Validation Expiration Limit (Preferences Menu):
a) Select default EGSE Expiration Limit and save.
b) Verify that the EGSE Configuration Log gets refreshed showing the new selected limit.
4) General Considerations
a) Attach print copy of FHW Configuration Log with known values:
_________________________________________________________________________________
b) Attach print copy of FSW Configuration Log with known values:
_________________________________________________________________________________
c) Attach print copy of EGSE Validation Configuration Log with known values:
_________________________________________________________________________________
7.3.9.3.
Overall Outcome of Test Case 7.3.9
Based on the analysis of the test results, the overall outcome of Test 7.3.9 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
7.3.10. Test Case: Configuration Request Log
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.10 corresponding to Test Case: Configuration Request Log
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
7.3.10.1.
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 26 of 30
Test Objective
Retrieve a time stamped list of users that requested a configuration log for either FHW, FSW or
EGSE validation records.
7.3.10.2.
Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) Configuration Request Log
a) In the Main Window press Config. Request Log.
b) The corresponding Configuration Request Log window displays a list with the following
information:
i) Configuration Log Type: FHW, FHW Matrix, FSW or EGSE Validation.
ii) User that requested the Configuration Log.
iii) Request Time stamp.
3) General Considerations
a) Attach print copy of Configuration Request Log with known values:
_________________________________________________________________________________
7.3.10.3.
Overall Outcome of Test Case 7.3.10
Based on the analysis of the test results, the overall outcome of Test 7.3.10 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
7.3.11. Test Case: Data Reporting Tools
This section describes the objectives, test scripts, procedure, and expected outcomes for Test ID
7.3.11 corresponding to Test Cases: Data Reporting Tools.
7.3.11.1.
Flight Hardware LAT Matrix Log
7.3.11.1.1. Test Objective
Verify that E-Logbook creates, retrieves and prints the FHW LAT Matrix Log. This Log will display
the current installation state of FHW Components in the LAT in a Bay grid Format.
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 27 of 30
7.3.11.1.2. Test Procedure
1) Record procedure start time and date:
__________________
Date
_____________ ________________ ______________
Time
Test Engineer
QAE
2) FHW LAT Matrix Log
a) In the Main Window FHW Installation tab press Matrix Log.
b) Enter username and password information that will be subsequently passed to the
Configuration Request Log (See Section 7.3.10).
c) The corresponding FHW LAT Matrix Log window displays the current installation state of
FHW Components in grid format:
i) Timestamp and User Name are displayed.
d) Weight units can be toggled between International and English system.
3) General Considerations
a) Attach print copy of FHW LAT Matrix Log with known values:
_________________________________________________________________________________
7.3.11.1.3. Overall Outcome of Test Case 7.3.11.1
Based on the analysis of the test results, the overall outcome of Test 7.3.9 is as follows:
□ Passed - all of the success conditions for the test were met.
□ Failed - one or more of the success conditions were not met.
__________________
Date
________________ ______________
Test Engineer
QAE
7.3.12. Test Case: Database Performance Tool (TBX)
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
8.
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 28 of 30
DEVIATIONS FROM THE QUALIFICATION TEST PROCEDURE
This section details any deviations from the hardware configuration, software configuration, or test
procedure followed during the execution of the test or tests described in this Qualification Test
Procedure document. All deviations from the approved procedure are agreed to by the Test Engineer
and the Software Quality Engineer during the test execution session. All deviations must be reported
during the Post Qualification Test Review, where their impact on the test results will be evaluated.
Hardware Deviations
Describe any deviations from the hardware configuration defined in Section 7.1.1. Name the
hardware that was modified and describe the modifications. If hardware is replaced during execution
of the test, name the replaced hardware, the manufacturer, and list an identification number (e.g.,
GLAT ID number).
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Software Deviations
Describe any changes made to the software configuration under test or the software configuration
used to support test execution, as defined in Section 7.1.2. Give version numbers of all E-Logbook
scripts and test packages that were modified. Describe how the contents of the modified software
load were verified. Describe these deviations for each test that was modified.
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05 GLAST LAT I&T E-Logbook Test Procedure and Report
Page 29 of 30
_________________________________________________________________________________
_________________________________________________________________________________
Procedural Deviations
Specify any deviations from the test procedure for the test being executed. If this document contains
more than one test procedure, list the procedure by number (e.g., “Test 7.3.1.”). List by number the
steps modified or skipped. Provide a numbered sequence listing any added steps. Describe these
deviations for each test that was modified.
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Known Issues
Specify any known issues that remain to be addressed at next release.
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.
LAT-PS-05664-05
9.
GLAST LAT I&T E-Logbook Test Procedure and Report
Page 30 of 30
CERTIFICATION
I certify that the information obtained under this test procedure is as represented and the information
recorded in this document is complete and correct. Any deviations from test procedures described
herein are identified in Section 8.
_________________
__________________________
________________________
Date
Test Engineer (Print Name)
Test Engineer (Signature)
I certify that the information obtained through execution of this test procedure is as represented and
the information recorded in this document is complete and correct. Execution of the test, storage of
the results, and verification of outcomes were carried out in accordance with quality standards
defined in the GLAST Quality Manual (LAT-MD-00091).
_________________ ___________________________
Date
_____________________________
Software QA Engineer (Print Name) Software QA Engineer (Sign)
I certify that the information obtained under this test procedure is as represented and the information
recorded in this document is complete and correct. The test procedure, as designed and executed,
does indeed verify that the E-Logbook functionality under test satisfies the corresponding
requirements from the E-Logbook Specification – LAT-MD-04601.
_________________
________________________
__________________________
Date
I&T Manager (Print Name)
I&T Manager (Signature)
Hard copies of this document are for REFERENCE ONLY and should not be
considered the latest revision beyond the date of printing.