LIST OF ATTEMPTED QUESTIONS AND ANSWERS
Multiple Choice Single Answer
Question
Any premise in which persons are employed for purpose
of making any product/s is called
Correct Answer Factory
Your Answer
Factory
True/False
Question
Objective of Work Study is to improve Productivity
Correct Answer True
Your Answer
True
True/False
Question
The OC curve is based on the assumption that if the lot is
large in comparison to the sample, the probabilities of the
OC curve will follow a poisson distribution.
Correct Answer False
Your Answer
True
Multiple Choice Multiple Answer
Question
What are the uses of failure statistics analysis?
Correct Answer To forecast the defect , To identify causes of major
repetative failures , To quantify the frequency of
preventive inspection
Your Answer
To forecast the defect , To identify causes of major
repetative failures , To quantify the frequency of
preventive inspection
True/False
Question
Systematic maintenance system can completely
eliminate the wear and tear of machines.
Correct Answer False
Your Answer
False
Select The Blank
Question
Production control work is ________ in case of floor
inspection as compared with the centralised inspection.
Correct Answer easier
Your Answer
time consuming
True/False
Question
Originating process of raw material influence Process
Planning
Correct Answer True
Your Answer
True
Multiple Choice Single Answer
Question
What is represented by an arrow in a network?
Correct Answer Activity
Your Answer
Activity
Multiple Choice Single Answer
Question
What do you mean by the selection of the job for the
method study on the basis of manufacturing difficulties?
Correct Answer Technical consideration
Your Answer
Manufacturing consideration
Multiple Choice Single Answer
Question
Who prepares the daily production report?
Correct Answer Shop Supervisor
Your Answer
Shop Supervisor
True/False
Question
Fixed cost is lower in case of continuous production than
intermittent production.
Correct Answer False
Your Answer
True
Select The Blank
Question
An ________ history card is the record of all repairs,
replacements and engineering changes carried out in the
equipment during it's period of service.
Correct Answer Equipment history card
Your Answer
Equipment history card
True/False
Question
Grouping of machines gives a lot of flexibility in loading
and scheduling
Correct Answer True
Your Answer
True
Multiple Choice Multiple Answer
Question
Which are the advantages of suburban location?
Correct Answer Avaialability of adequate land at lower cost , Both skilled
and unskilled labour can be available , Plant expansion is
easier due to less or no restriction for building and
construction
Your Answer
Avaialability of adequate land at lower cost , Both skilled
and unskilled labour can be available , Plant expansion is
easier due to less or no restriction for building and
construction
Select The Blank
Question
The ________ is the probability that a good lot will be
rejected by the sampling plan.
Correct Answer Producer's risk
Your Answer
Producer's risk
Multiple Choice Single Answer
Question
Technique of Value Engineering can be effectively
employed in design of a product to
Correct Answer To meet the intended function at lowest cost
Your Answer
To meet the intended function at lowest cost
Multiple Choice Single Answer
Question
Which kind of preventive inspection detects some
maintenance related characteristics by making use of
human senses, when equipment is in operation?
Correct Answer Extrernal inspection
Your Answer
Daily inspection
Multiple Choice Multiple Answer
Question
Route Sheet generally contains following information
Correct Answer Material Specification , Sequence of operation , Skill of
Labour
Your Answer
Material Specification , Sequence of operation , Order
Quantity
Multiple Choice Single Answer
Question
Data from Process Sheet can be used to
Correct Answer Prepare load and schedule charts
Your Answer
Prepare load and schedule charts
Multiple Choice Single Answer
Question
The ratio of output to input of a production system is
commonly known as
Correct Answer Productivity
Your Answer
Productivity
Match The Following
Question
Correct Answer
Your Answer
Net requirement of
material under MRP
Stock on hand
Stock on hand
Fixation of inventory
level
Reorder level
Reorder level
Symptom of ill planned Over ordering
purchasing
Over ordering
Factor influencing
material planning
Price of material
Lead time
Multiple Choice Multiple Answer
Question
Which of the following products should be produced by
using mass production?
Correct Answer Refrigerator , Tyre for automobile , Television Set
Your Answer
Refrigerator , Tyre for automobile , Television Set
Select The Blank
Question
The ________ is necessary when the job requires
detailed of one or more of the job characteristics with the
help of special equipment which is not available at the
producing company.
Correct Answer Inspection order
Your Answer
Job card
True/False
Question
Limit gauges are not useful when it is necessary to
measure the exact amount of variation.
Correct Answer True
Your Answer
False
Multiple Choice Single Answer
Question
A good plant layout helps in
Correct Answer Reducing handling costs
Your Answer
Reducing handling costs
Select The Blank
Question
In case of an OC curve, the risk of rejecting a good
quality lot may vary between ________.
Correct Answer 0.01 to 10%
Your Answer
0.10 to 10%
Select The Blank
Question
The ________ is the maximum percentage defective that
for the purpose of sampling inspection can be considered
satisfactory as a process average.
Correct Answer Acceptable quality level
Your Answer
Acceptable quality level
Multiple Choice Multiple Answer
Question
Which of the following is not the characteristic of Project
Production?
Correct Answer Continuous flow of material , Highly mechanised material
handling , Virtually zero manufacturing cycle time
Your Answer
Continuous flow of material , Virtually zero manufacturing
cycle time
Select The Blank
Question
Goods after final inspection should accompany
________to enable dispatch department to identify and
draw correct reference.
Correct Answer Forwarding note
Your Answer
Move order
Select The Blank
Question
Production Planning is a centralised activity which
includes functions such as ________
Correct Answer Scheduling
Your Answer
Expediting
Multiple Choice Multiple Answer
Question
Which of the following are steps to identify the critical
path in a small network?
Correct Answer Compare the durations of all paths to identify the longest
path. , Sum up the durations of activities along each path.
, Enumerate all paths in the network and list down
activities on each path.
Your Answer
Compare the durations of all paths to identify the longest
path. , Sum up the durations of activities along each path.
, Enumerate all paths in the network and list down
activities on each path.
Select The Blank
Question
Capacity decisions have a direct influence on
performance of production system in respect of
________
Correct Answer Delivery performance
Your Answer
Delivery performance
True/False
Question
Floor inspection promotes tendency of machines to drift
out of limits and produce defectives.
Correct Answer False
Your Answer
False
True/False
Question
Even if any activity on the critical path is delayed, project
completes on the scheduled time.
Correct Answer False
Your Answer
False
Multiple Choice Multiple Answer
Question
Which are different ways to show critical path in a
network?
Correct Answer Thick Line , Red Line , Double Line
Your Answer
Thick Line , Red Line , Double Line
Multiple Choice Single Answer
Question
Which phase of method study is concerned with
analyzing the facts critically, generating alternatives
which form the basis for selection and development of
improved methods?
Correct Answer Critical examination
Your Answer
Development and selection
True/False
Question
Operation Process Chart provides information on time
and distances
Correct Answer False
Your Answer
False
Multiple Choice Single Answer
Question
The document which incorporates details of process
planning for a job is called
Correct Answer Route Sheet
Your Answer
Route Sheet
Multiple Choice Single Answer
Question
The process of changing inputs into outputs thereby
adding some value to entity can be defined as
Correct Answer Operation
Your Answer
Manufacturing
Select The Blank
Question
The ________ are the definitions of the measurable as
well as nonmeasurable characteristics of the product.
Correct Answer Specifications
Your Answer
Specifications
Multiple Choice Multiple Answer
Question
Which of the following method can be adopted to
overcome the problem of rushing up a job for it's timely
completion?
Correct Answer Use of optimum speeds and feeds , Subcontracting , Job
splitting
Your Answer
Use alternative materials , Subcontracting , Job splitting
Multiple Choice Multiple Answer
Question
What is the basic minimum requirement for those who
are responsible for the quality of design?
Correct Answer In depth knowledge about alternative materials and
manufacturing processes , access to latest technology
and production process adopted by industries in the
developed market , Continuous effort in product
development
Your Answer
In depth knowledge about alternative materials and
manufacturing processes , access to latest technology
and production process adopted by industries in the
developed market , Continuous effort in product
development
Multiple Choice Single Answer
Question
Following is not an input information for Process Planning
Correct Answer Inventory level
Your Answer
Drawings
Multiple Choice Single Answer
Question
Which kind of inspection is followed in case of product
layout?
Correct Answer Pilot inspection
Your Answer
Vendor inspection
Match The Following
Question
Correct Answer
Bottom compartment of Bunch of work orders
control board
arranged in a sequence
in which they are to be
processed.
Your Answer
Bunch of work orders
arranged in a sequence
in which they are to be
processed.
Control board
Pictorial view of
Pictorial view of machine
machine loading activity loading activity
Top compartment of
control board
Work order of item
Work order of item
currently being worked currently being worked
on the machine
on the machine
Middle compartment of Work order of item to be Work order of item to be
control board
processed next on the processed next on the
machine
machine
Select The Blank
Question
The ________ is the probability that a bad lot will be
accepted by the sampling plan.
Correct Answer Consumer's risk
Your Answer
Consumer's risk
Multiple Choice Single Answer
Question
How to reveal the capability of the sampling plan to
discriminate between good lots and bad lots?
Correct Answer Operating characteristics curve ( OC )
Your Answer
Operating characteristics curve ( OC )