POM assgn : Seema Select The Blank Question

advertisement
POM assgn : Seema
Select The Blank
Question
The ________ is the process of withdrawing the equipment from the production line,
dismantling it unitwise, visualising defects, effecting adjustments, replacing worn-out
parts and finally building it up to get desired accuracies.
Correct
Reconditioning
Answer
Your Answer
Overhauling
Multiple Choice Single Answer
Question
What do you understand by the measurement of work to establish allowed time for a job
for the defined method?
Correct
Work measurement
Answer
Your Answer
Work measurement
Multiple Choice Single Answer
Question
The ratio of output to input of a production system is commonly known as
Correct
Answer
Your Answer
Productivity
Productivity
Multiple Choice Single Answer
Question
What is the location of lower control limit in the X bar-R control chart?
Correct
Answer
Your Answer
3 standard deviations below central line
2 standard deviations below central line
Match The Following
Question
Correct Answer
Your Answer
Factor Analysis
Method to evaluate layouts
Technique for evolving and analysis
of layouts
Minimization of production delays Objective of good layout
Principles of good layout
Maximum visibility
Principles of good layout
Layout analysis
Scale model
Layout analysis
Method to evaluate layouts
Multiple Choice Single Answer
Question
What is the name of the document on which details of the process are recorded by the
symbols and charting conventions?
Correct
Chart
Answer
Your Answer
Chart
Multiple Choice Single Answer
Question
Which kind of inspection is followed in case of process layout?
Correct
Answer
Your Answer
First off inspection
Cent percent inspection
Multiple Choice Multiple Answer
Question
Which of the following defects can be observed during preventive inspection by using
human senses?
Correct
Deviation from normal sound , Excessive Vibration , Leakage of a gas
Answer
Your Answer
Deviation from normal sound , Excessive Vibration , Leakage of a gas
True/False
Question
Correct
Answer
Your Answer
Process Sheets for parts in batch production are not maintained as standard process
sheet
False
True
Select The Blank
Question
Goods after final inspection should accompany ________to enable dispatch department
to identify and draw correct reference.
Correct
Forwarding note
Answer
Your Answer
Move order
Select The Blank
Question
A set of activities to keep an equipment in the specified condition is called as ________.
Correct
Answer
Your Answer
Maintenance
Maintenance
Multiple Choice Multiple Answer
Question
What are the advantages of three dimensional models?
Correct
Answer
Your Answer
Overhead facilities can be shown , Can be shifted easily and quickly , Even non-technical
person can use it
Overhead facilities can be shown , Economical , Can be shifted easily and quickly
Select The Blank
Question
The ________ is the maintenance work initiated on a result of knowledge of the
condition of an item from routine or continuous checking.
Correct
Condition monitoring
Answer
Your Answer
Preventive maintenance
Multiple Choice Single Answer
Question
What do you understand by the selection of the job for the method study on the basis of
money saving potential of the job?
Correct
Economic consideration
Answer
Your Answer
Economic consideration
Select The Blank
Question
Capacity decisions have a direct influence on performance of production system in
respect of ________
Correct
Delivery performance
Answer
Your Answer
Quality
Multiple Choice Multiple Answer
Question
Which of the following are the objectives of a good maintenance system?
Correct
Answer
Your Answer
Elimination of unsafe conditions , Minimisation of wear and tear of machines , Ensuring
maximum plant availability
Elimination of unsafe conditions , Minimisation of wear and tear of machines , Ensuring
maximum plant availability
Match The Following
Question
Correct Answer
Your Answer
First off inspection
First piece produced after tool
change
First piece produced after tool
change
Critical operation inspection
After whose no rework is possible Last operation
Patrolling inspection
Inspection at the place of actual
production
Inspection at the place of actual
production
Key operation inspection
Costlier operation
After whose no rework is possible
True/False
Question
Correct
Answer
Your Answer
In case of backward pass computation, the latest event time of a tail event equals to the
latest event time of the succeeding ( Head ) event minus duration of the activity
converging to the head event..
True
True
Multiple Choice Multiple Answer
Question
Which of the following factors affect the quality control function?
Correct
Answer
Your Answer
Quality of workmanship , Production aids , Manufacturing facilities
Quality of workmanship , Production aids , Manufacturing facilities
Multiple Choice Multiple Answer
Question
Which of the following products should be produced by using mass production?
Correct
Answer
Your Answer
True/False
Refrigerator , Tyre for automobile , Television Set
Refrigerator , Tyre for automobile , Television Set
Question
Correct
Answer
Your Answer
True/False
Question
Correct
Answer
Your Answer
True/False
Question
Correct
Answer
Your Answer
Cent percent inspection does not mean inspection of component for 100% quality
characteristics.
True
True
Cellular layout is based on the concept of Group Technology
True
True
A lot declared rejected in sampling inspection should not be inspected 100% in any case.
False
False
Multiple Choice Single Answer
Question
Which kind of relationship exists between those activities which can be carried out
simultaneously and both activities require definite time to finish?
Correct
Concurrent activities
Answer
Your Answer
Concurrent activities
True/False
Question
Correct
Answer
Your Answer
Recording of movement is not necessary in case of method study in any form.
False
False
Select The Blank
Question
The ________ includes preventive maintenance activities whose needs are identified
through inspection which requires stoppage of machines.
Correct
Shutdown Maintenance
Answer
Your Answer
Shutdown Maintenance
Select The Blank
Question
Production control work is ________ in case of floor inspection as compared with the
centralised inspection.
Correct
easier
Answer
Your Answer
easier
True/False
Question
In case of backward pass computation, the latest event time of the burst event equals
the smallest of the difference between the latest event time of the head event less
duration of the activity converging on the head event.
Correct
Answer
Your Answer
True
True
Select The Blank
Question
The ________ breakdowns usually cost more, partly due to damage done to the
adjustment components and partly due to emergency actions.
Correct
Unexpected
Answer
Your Answer
Unexpected
Multiple Choice Multiple Answer
Question
Which of the following are examples of addition during recording for method study?
Correct
Answer
Your Answer
Brazing , Welding , Riveting
Brazing , Welding , Riveting
Multiple Choice Multiple Answer
Question
Which kind of natural delays and interruptions are considered during estimation of
activity time?
Correct
Shop efficiency , Breakdowns , Absenteeism
Answer
Your Answer
Shop efficiency , Breakdowns , Absenteeism
Multiple Choice Single Answer
Question
How does the control chart of statistical quality control helps the operating personnel?
Correct
Answer
Your Answer
True/False
Question
Correct
Answer
Your Answer
Identify the presence of an assignable cause before it develops
Identify the presence of an assignable cause before it develops
Inspection Order can be a verbal order
True
True
Multiple Choice Multiple Answer
Question
Lack of material planning results in the following
Correct
Answer
Your Answer
Over ordering , under ordering , stockouts
Over ordering , under ordering , stockouts
Multiple Choice Single Answer
Question
Inherent Safety' is one of the principle of good layout. In context of layout, this can be
achieved by the following
Correct
Answer
Your Answer
Clear gangway, location of material and material handling system
Proper plant location
Multiple Choice Multiple Answer
Question
What are the benefits of reconditioning?
Correct
Answer
Your Answer
Eliminates problems and frequent breakdowns , Increases life of an equipment , It helps
to plan requirement of replacement spares
Eliminates problems and frequent breakdowns , Increases life of an equipment , It helps
to plan requirement of replacement spares
Multiple Choice Multiple Answer
Question
Which are the general principles underlying probability aspects of project planning?
Correct
Answer
Your Answer
Statistically three time estimate of an activity conform to Beta distribution. , Expected
time divides the area under the curve into two equal parts. , Expected time of an activity
is located at one third of the distance between "m" and mid-range { (a+b)/2 } away
from the most likely time.
Statistically three time estimate of an activity conform to Beta distribution. , Expected
time divides the area under the curve into three equal parts. , Expected time of an
activity is located at one third of the distance between "m" and mid-range { (a+b)/2 }
away from the most likely time.
Select The Blank
Question
OC curve of ideal sampling plan suggests that all lots less than 3% defectives have the
probability of acceptance of ________.
Correct
One
Answer
Your Answer
0.5
True/False
Question
Correct
Answer
Your Answer
Grouping of machines gives a lot of flexibility in loading and scheduling
True
True
Select The Blank
Question
The ________ is specified to indicate the maximum permissible variability in the
dimensions product or parts.
Correct
Tolerance
Answer
Your Answer
Tolerance
Multiple Choice Single Answer
Question
What is the nature of the sampling plan for critical defects?
Correct
Answer
Your Answer
Tight
Tight
Multiple Choice Multiple Answer
Question
Correct
Answer
Your Answer
Which are the first three steps of Critical Path Analysis technique?
Activity relationships , Activity identification , Network construction
Activity relationships , Activity identification , Network construction
Select The Blank
Question
The ________ is the maximum percentage defective that for the purpose of sampling
inspection can be considered satisfactory as a process average.
Correct
Acceptable quality level
Answer
Your Answer
Lot Tolerance Percentage Defective
Multiple Choice Single Answer
Question
What do you understand by the critical analysis of existing jobs to develop easier and
effective method?
Correct
Method study
Answer
Your Answer
Method study
Multiple Choice Multiple Answer
Question
Which utilities are considered as infrastructural requirements?
Correct
Answer
Your Answer
True/False
Question
Correct
Answer
Your Answer
Disposal of waste , Power , Water
Power , Labour , Water
During set up of X bar-R control chart, control limts should be practically revised from
time to time as additional data is accumulated.
True
False
Multiple Choice Single Answer
Question
What do you understand by identification of defects in materials, components, machining
processes or men to fix responsibility of defectives, thereby preventing or minimising
occurance of defectives?
Correct
Preventive function
Answer
Your Answer
Preventive function
Download