POM assgn : Parmeet Multiple Choice Multiple Answer Question
advertisement
POM assgn : Parmeet Multiple Choice Multiple Answer Question What is indicated by the hugging points lying close to mean of the process in X bar-Rcontrol chart? Correct Answer Recording done without actual measurements , Improper selection of samples , Biases in measurements Your Answer Improper selection of samples , Biases in measurements , Recording done without actual measurements Multiple Choice Multiple Answer Question Which of the following are the basic requirements of quality standard? Correct Answer Deifinite , Undesrstandable , Economically viable Your Answer Deifinite , Undesrstandable , Economically viable Match The Following Question Correct Answer Your Answer Fixation of inventory level Reorder level Reorder level Symptom of ill planned purchasing Over ordering Over ordering Factor influencing material planning Lead time Lead time Net requirement of material under Stock on hand MRP Stock on hand Multiple Choice Multiple Answer Question What are the benefits of inspection and quality control? Correct Answer Adequate maintenance of quality , Ensures parts are within specified limits of accuracy , Gives economy in production through reduction of defective work Your Answer Adequate maintenance of quality , Ensures parts are within specified limits of accuracy , Gives economy in production through reduction of defective work Select The Blank Question The ________ advocates maintenance procedures whereby the condition of the plant is constantly watched through systematic inspection to unearth unhealthy conditions and preventive Correct Answer Preventive Maintenance Your Answer Preventive Maintenance Multiple Choice Single Answer Question What do you mean by design modifications made to reduce time and effort required in carrying out maintenance work ? Correct Answer Design-in Maintenance Your Answer True/False Question Design-in Maintenance Even in a small set up wherein maintenance of a machine is looked after by a mechanic cum worker, he should report directly to the person responsible for the manufacturing operations. Correct Answer True Your Answer True Multiple Choice Single Answer Question Which of the following technique makes three time estimates for each activity? Correct Answer Project Evaluation & Review Technique Your Answer Project Evaluation & Review Technique Select The Blank Question A set of activities to keep an equipment in the specified condition is called as ________. Correct Answer Maintenance Your Answer Maintenance Multiple Choice Multiple Answer Question Which of the following are characteristics of an operating characteristics curve? Correct Answer Producer risk , Consumer Risk , Acceptable Quality Level Your Answer Producer risk , Consumer Risk , Acceptable Quality Level Multiple Choice Multiple Answer Question Which three of the following are causes of continuous upward pattern of Xbar-R control chart? Correct Answer Wear of tool , Abnormal rise in temperature , Accumulation of dirt Your Answer Wear of tool , Untrained operator , Abnormal rise in temperature True/False Question Inspection should be conducted on all incoming materials, semifinished items, bought out components, subcontract items prior to any operation, assembly. Correct Answer True Your Answer True Select The Blank Question The ________ is necessary when the job requires detailed of one or more of the job characteristics with the help of special equipment which is not available at the producing company. Correct Answer Inspection order Your Answer Inspection order Multiple Choice Multiple Answer Question Lack of material planning results in the following Correct Answer Over ordering , under ordering , stockouts Your Answer Over ordering , under ordering , stockouts True/False Question Since value of c can never be negativee, hence" if LCLp works out to be negative, it is taken as zero." Correct Answer True Your Answer False Multiple Choice Single Answer Question What do you understand by the quality specified by the designer on behalf the customer? Correct Answer Quality of design Your Answer Quality of design Select The Blank Question The easiest way to bring the delayed job within the promised delivery time by using extra shift or weekly holiday is ________. Correct Answer Overtime working Your Answer Overtime working Select The Blank Question Work study is also called ________ study Correct Answer Time and Motion Your Answer Time and Motion True/False Question Maintenance function must be decentralised apart from a size of a manufacturing organisation for it's better functioning. Correct Answer False Your Answer False True/False Question Repetitive movements between work stations which are difficult to be traced on string diagrams can be conveniently shown on flow diagrams. Correct Answer False Your Answer False Multiple Choice Single Answer Question Which method is used to trace especially those movements which are too fast for human eye to pursue? Correct Answer Cyclegraph Your Answer Cyclegraph Match The Following Question Correct Answer Your Answer Template Two dimensional cutouts Two dimensional cutouts REL chart Degree of closeness Degree of closeness Flow diagram Tracing movements Tracing movements Travel chart Distance and frequency of movements Distance and frequency of movements Select The Blank Question An Ideal OC curve is ________ shaped curve that accpets all the lots with quality equal to or better than AQL . Correct Answer Rectangular Your Answer Rectangular Multiple Choice Single Answer Question What does the points falling outside the control limits indicate? Correct Answer Presence of assignable causes Your Answer Presence of chance causes Multiple Choice Multiple Answer Question Which information is recorded in an equipment card? Correct Answer Date of commissioning , Equipment specifications , Name and address of manufacturer Your Answer Date of commissioning , Equipment specifications , Name and address of manufacturer True/False Question Inspection should be avoided prior to long run of a manufacturing stage as it becomes duplication of work and cost. Correct Answer False Your Answer False True/False Question Delay in completion of projects result in unwelcome additions to the fixed manufacturing expenses. Correct Answer True Your Answer True Multiple Choice Single Answer Question Material Planning is an integral part of Correct Answer Production Planning Your Answer Production Planning Multiple Choice Single Answer Question Which of the following policies is advisable in case of low product variety and large volumes? Correct Answer Low Skilled Labour & Special Purpose Machines Your Answer Low Skilled Labour & Special Purpose Machines Select The Blank Question In case of an OC curve, the risk of rejecting a good quality lot may vary between ________. Correct Answer 0.01 to 10% Your Answer 0.01 to 10% Multiple Choice Single Answer Question MRP is based on the concept of inventory demand which is of following type Correct Answer Dependent and independent Your Answer Dependent and independent True/False Question In case of X bar, if the process is not under control indicated by some points falling outside the control limits, such points outside the control limits are eliminated and new trial control limits for the remaining points are computed. Correct Answer True Your Answer True Multiple Choice Multiple Answer Question Plant Layout is concerned with optimum arrangement of the following Correct Answer Storage space , Machines , Material Handling Equipment Your Answer Storage space , Machines , Material Handling Equipment Multiple Choice Single Answer Question What is the location of upper control limit in the X bar-R control chart? Correct Answer 3 standard deviations above central line Your Answer 3 standard deviations above central line Select The Blank Question The ________ is the defect level for which lots are regarded as bad lots. Correct Answer Lot Tolerance Percentage Defective Your Answer Lot Tolerance Percentage Defective True/False Question While numbering as per Fulkerson's rule, arrows emerging from the initial event are deleted so as to create one or more initial events. Correct Answer True Your Answer False Multiple Choice Single Answer Question Why stores issue order should not be issued as soon as it is prepared? Correct Answer Material may or may not be available at the time of preparation Your Answer Material may or may not be available at the time of preparation Multiple Choice Single Answer Question Which characteristics are verified in cent percent sampling? Correct Answer All important characteristics Your Answer Only characteristics related to performance Select The Blank Question An ________ history card is the record of all repairs, replacements and engineering changes carried out in the equipment during it's period of service. Correct Answer Equipment history card Your Answer Equipment history card Multiple Choice Multiple Answer Question Features of Cellular layout are Correct Answer It is a type of mixed layout , Uses concept of Group Technology , Facilities are grouped in to cells Your Answer It is a type of mixed layout , Uses concept of Group Technology , Facilities are grouped in to cells Multiple Choice Single Answer Question Inadequate production capacity ultimately leads to Correct Answer Poor Customer Service Your Answer Poor Customer Service Multiple Choice Multiple Answer Question Which of the following factors affect the quality control function? Correct Answer Quality of workmanship , Production aids , Manufacturing facilities Your Answer Quality of workmanship , Competitive prices , Manufacturing facilities Multiple Choice Multiple Answer Question Which of the following situations demand the economic consideration while selecting a job for method study? Correct Answer Unorderly movement of men and materials , Excessive process defectives , Too many suggestions received for improvement from a department or section Your Answer Unorderly movement of men and materials , Excessive process defectives , Too many suggestions received for improvement from a department or section True/False Question Systematic maintenance system can completely eliminate the wear and tear of machines. Correct Answer False Your Answer False Select The Blank Question Capacity decisions have a direct influence on performance of production system in respect of ________ Correct Answer Delivery performance Your Answer Delivery performance Select The Blank Question The ________ must ensure that the product satisfy the functional requirements of it's usage. Correct Answer Quality of design Your Answer Quality of design Multiple Choice Multiple Answer Question Which of the following can be subtypes of corrective maintenance? Correct Answer Shutdown Maintenance , Design-out Maintenance , Design-in Maintenance Your Answer Shutdown Maintenance , Design-out Maintenance , Design-in Maintenance