NZQA registered unit standard
1106 version 5
Page 1 of 4
Title
Perform drain maintenance
Level
3
Purpose
Credits
5
This unit standard is for people who work in the drainlaying
industry.
People credited with this unit are able to: identify drain defects
and their rectification; clear, repair and replace defective drains;
carry out backfilling and clear the site; and work safely and with
care.
Classification
Plumbing, Gasfitting and Drainlaying > Drainlaying
Available grade
Achieved
Entry information
Critical health and
safety prerequisites
Unit 1099, Excavate and trench for plumbing, gasfitting, or
drainlaying; or demonstrate equivalent knowledge and skills.
Candidates who are working within the jurisdiction of the
Plumbers, Gasfitters and Drainlayers Board must hold a
current drainlaying limited certificate or exemption for
drainlaying under supervision as issued under the Plumbers,
Gasfitters and Drainlayers Act 2006.
Explanatory notes
1
Legislation, standards, codes, and guides applicable to this unit standard include but
are not limited to:
Plumbers, Gasfitters, and Drainlayers Act 2006
Health and Safety in Employment Act 1992
Building Act 2004
Health Act 1956
Resource Management Act 1991
Plumbers, Gasfitters, and Drainlayers Regulations 2010
AS/NZS 1547:2000 On-site domestic wastewater management (available at
http://www.standards.co.nz)
AS/NZS 1546.1:2008 On-site domestic wastewater treatment units – Septic tanks
(available at http://www.standards.co.nz)
AS/NZS 3500.2:2003 Plumbing and drainage – Sanitary plumbing and drainage
(available at http://www.standards.co.nz)
The Skills Organisation
SSB Code 101554
 New Zealand Qualifications Authority 2016
NZQA registered unit standard
1106 version 5
Page 2 of 4
Approved Code of Practice for Safety in Excavation and Shafts for Foundations
(Wellington:
Department
of
Labour,
1995)
(available
at
http://www.osh.govt.nz/order/catalogue)
Guide for Safety with Underground Services (Wellington: Department of Labour
2002) (available at http://www.osh.govt.nz/order/catalogue)
New Zealand Building Code Clause E1 Surface Water and any related compliance
documents (available at http://www.dbh.govt.nz)
New Zealand Building Code Clause G12 Water Supplies and any related compliance
documents (available at http://www.dbh.govt.nz)
New Zealand Building Code Clause G13 Foul Water and any related compliance
documents (available at http://www.dbh.govt.nz).
Any legislation, standard, code, or guide superseding any of the above will apply,
pending review of this unit standard.
2
Definitions
Job specifications, for the purpose of this unit standard, refer to instructions (oral,
written, graphic) and may include any of the following: manufacturers’ instructions;
design drawing detail specifications; specifications from a specialist source such as
an architect, designer, engineer, or a supervisor; and site or work specific
requirements. Where job specifications are in conflict with applicable legislation,
standards, and/or codes, such legislation, standards, and/or codes shall take
precedence for the purpose of assessment.
Other services, for the purposes of this unit standard, refer to any existing installed
services such as water, gas, electricity, or telephone network cables.
Outcomes and evidence requirements
Outcome 1
Identify drain defects and their rectification.
Evidence requirements
1.1
Defects are identified in terms of location, type, and cause.
1.2
Means of rectification is identified.
Range
repair, replace, or clear.
Outcome 2
Clear, repair, and replace defective drains.
Evidence requirements
2.1
Clearing procedure ensures free flow of materials.
2.2
Drain is repaired in accordance with the drain type and job specifications.
2.3
The drain is replaced in accordance with job specifications.
The Skills Organisation
SSB Code 101554
 New Zealand Qualifications Authority 2016
NZQA registered unit standard
2.4
1106 version 5
Page 3 of 4
The installation meets requirements of the Building Act 2004.
Outcome 3
Carry out backfilling and clear the site.
Evidence requirements
3.1
Site is backfilled, and compacted as necessary, in accordance with job
specifications.
3.2
Site is cleared of construction debris and working equipment.
Outcome 4
Work safely and with care.
Evidence requirements
4.1
Practical activities are carried out avoiding harm to people and damage to
property, other services, materials, tools, and equipment.
Planned review date
31 December 2017
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
31 January 1994
N/A
Revision
2
19 June 1996
N/A
Revision
3
3 April 1997
N/A
Review
4
25 October 2007
N/A
Review
5
15 March 2012
N/A
Consent and Moderation Requirements (CMR) reference
0008
This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA,
before they can report credits from assessment against unit standards or deliver courses
of study leading to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
The Skills Organisation
SSB Code 101554
 New Zealand Qualifications Authority 2016
NZQA registered unit standard
1106 version 5
Page 4 of 4
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Requirements for consent to assess and an outline of the moderation system that applies
to this standard are outlined in the Consent and Moderation Requirements (CMR). The
CMR also includes useful information about special requirements for organisations wishing
to develop education and training programmes, such as minimum qualifications for tutors
and assessors, and special resource requirements.
Comments on this unit standard
Please contact The Skills Organisation info@skills.org.nz if you wish to suggest changes
to the content of this unit standard.
The Skills Organisation
SSB Code 101554
 New Zealand Qualifications Authority 2016