NZQF NQ Ref Version 1690 Page 1 of 15 2 National Certificate in Solid Wood Manufacturing (Level 2) with strands in Defecting; Finger Jointing and Laminating; Pole, Post and Pile; Saw Doctoring Principles; Sawmilling; Timber Drying and Treatment; and Timber Machining Level 2 Credits 45-63 This qualification has been reviewed. The last date to meet the requirements is 31 December 2018. Transition Arrangements This qualification has been reviewed and replaced by the New Zealand Certificate in Solid Wood Manufacturing (Level 2) with strands in Finger Jointing; Laminating; Pole, Post and Pile; Sawmilling; Timber Drying and Treatment; Timber Grading; Timber Machining; and Wood Pallet Manufacturing [Ref: 1967]. People currently working towards this expiring qualification may either complete the requirements for the qualification by 31 December 2018 or transfer their results to the replacement New Zealand qualification. New enrolments into programmes leading to this expiring qualification will not be accepted after 31 December 2015. It is anticipated that no existing candidates will be disadvantaged by these transition arrangements. However, anyone who feels that they have been disadvantaged may appeal to Competenz at the address below. Appeals will be considered on a case by case basis. For detailed information see Review Summaries on the NZQA website. NZQF National Qualification Registration Information Process Registration Review Competenz SSB Code 101571 Version 1 2 Date July 2011 April 2014 Last Date for Assessment December 2018 December 2018 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version 2 Page 2 of 15 Standard Setting Body Competenz PO Box 9005 Newmarket Auckland 1149 Telephone Fax Email Website 0800 526 1800 09 539 9899 qualifications@competenz.org.nz www.competenz.org.nz Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref Version 1690 2 Page 3 of 15 National Certificate in Solid Wood Manufacturing (Level 2) with strands in Defecting; Finger Jointing and Laminating; Pole, Post and Pile; Saw Doctoring Principles; Sawmilling; Timber Drying and Treatment; and Timber Machining Level 2 Credits 45-63 Purpose This qualification recognises the foundation skills and knowledge required of employees in a range of solid wood manufacturing industries. The core compulsory section covers industry foundation skills including an understanding of the health, safety, and environmental risks associated with the workplace; the factors that affect performance in the workplace; an introduction to workplace communication; workplace structures and workplace organisation, and physical characteristics of wood. The core compulsory section of this qualification shares unit standards in common with the National Certificate in Wood Manufacturing Foundation Skills (Wood Panels) (Level 2) [Ref: 1691] and the National Certificate in National Certificate in Wood Manufacturing Foundation Skills (Wood Handling and Distribution) (Level 2) [Ref: 1692]. The core compulsory section of these qualifications recognises skill and knowledge requirements that are transferable across the different wood manufacturing sectors. The qualification’s strands recognise the competencies required to work responsibly and safely in entry level roles in a diverse range of the solid wood manufacturing industries including: operating and maintaining a cross cut saw centre, and grading and wrapping for defecting operations knowledge of wood product, wood quality and principles of finger jointing and laminating, and operating stacking, feeding and sawing machinery used in finger jointing and laminating operations grading, stacking and saw centre operation in pole, post and pile production and knowledge of phytosanitary standards, log yarding, log making and chainsaw use for pole, post and pile operations knowledge of saws, knives, grinding and sawmilling, and setting circular saws and maintaining cutting tools used in saw doctoring knowledge of sawmilling principles, phytosanitary standards and timber grading, and operating stacking systems and saw centre machinery, and stock processing in sawmilling operations knowledge of wood preservation and drying, and storage and handling of timber and chemicals used in timber drying and treatment operations knowledge of timber machining, wood product, wood quality, drying, and stacking, wrapping and tallying timber for timber machining operations. This qualification may lead on to the National Certificate in Solid Wood Manufacturing (Level 3) with strands in Engineered Wood Product Operations; Planer Operations; Pole, Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref Version 1690 Page 4 of 15 2 Post and Pile Operations; Saw Doctoring Operations; Sawmilling Operations; Timber Drying Operations; Timber Grading; and Timber Treatment Operations, [Ref: 1693]; or the National Certificate in Wood Handling and Distribution (Level 3) with strands in Log Yard and Wood Preparation, and Timber Yarding and Despatch [Ref: 1308]; depending on the wood manufacturing operations that candidates are engaged in. Replacement Information This qualification, the National Certificate in Wood Manufacturing Foundation Skills (Wood Panels) (Level 2) [Ref: 1691] and the National Certificate in Wood Manufacturing Foundation Skills (Wood Handling and Distribution) (Level 2) [Ref: 1692], replaced the National Certificate in Wood Manufacturing Foundation Skills (Level 2) with strands in Solid Wood Manufacturing, Sliced Veneer Operations, Technical Awareness, Wood Handling and Distribution, Wood Panel Manufacturing, and Wood Product Manufacturing [Ref: 1305]. Special Notes It is recommended that candidates hold a current first aid certificate or are credited with the following first aid standards – Unit 26551, Provide first aid for life threatening conditions; and Unit 26552, Demonstrate knowledge of common first aid conditions and how to respond to them. Credit Range Core Compulsory Level 2 credits Level 3 credits Minimum totals Qualification total with strand Level 2 credits Level 3 credits Minimum totals Qualification total with strand Competenz SSB Code 101571 30 30 Defecting Strand Compulsory Elective 5-13 5 0-8 5 13 48 Finger Jointing and Laminating Strand Compulsory Elective 1 Elective 2 10 5 0-5 10-15 10 20 60 New Zealand Qualifications Authority 2016 NZQF NQ Ref Version 1690 Page 5 of 15 2 Pole, Post and Pile Strand Level 2 credits Level 3 credits Minimum totals Qualification total with strand Compulsory 8 10 18 Elective 5-10 0-5 10 58 Sawmilling Strand Level 2 credits Level 3 credits Minimum totals Qualification total with strand Level 2 credits Level 3 credits Minimum totals Qualification total with strand Compulsory 5 5 Elective 0-10 0-10 10 45 Saw Doctoring Principles Strand Compulsory Elective 15 0-3 15 0-5 30 3 63 Timber Drying and Treatment Strand Compulsory Elective 10 2-10 0-8 10 10 50 Timber Machining Strand Compulsory Elective 15 0-3 5 0-5 20 3 53 Requirements for Award of Qualification Award of NZQF National Qualifications Credit gained for a standard may be used only once to meet the requirements of this qualification. Unit standards and achievement standards that are equivalent in outcome are mutually exclusive for the purpose of award. The table of mutually exclusive standards is provided on the New Zealand Qualifications Authority (NZQA) website: http://www.nzqa.govt.nz/qualifications-standards/standards/standards-exclusionlist/. Reviewed standards that continue to recognise the same overall outcome are registered as new versions and retain their identification number (ID). Any version of a standard with the same ID may be used to meet qualification requirements that list the ID and/or that specify the past or current classification of the standard. Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 6 of 15 2 Summary of Requirements Core Compulsory standards One of the following strands is required Defecting Strand Finger Jointing and Laminating Strand Pole, Post and Pile Strand Saw Doctoring Principles Strand Sawmilling Strand Timber Drying and Treatment Strand Timber Machining Strand Detailed Requirements Core Compulsory The following standards are required Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 736 22970 22973 22977 Demonstrate knowledge of physical characteristics of wood Demonstrate employment and interrelationship foundation skills in a wood manufacturing operation Demonstrate knowledge of factors that affect the performance of wood manufacturing workers Demonstrate knowledge of workplace risks in a wood manufacturing operation 2 5 2 10 2 10 2 5 Level Credit 3 5 Defecting Strand Meet the requirements of all of the following sets Defecting Strand Compulsory Defecting Strand Elective Defecting Strand Compulsory The following standard is required Manufacturing > Solid Wood Manufacturing > Sawmilling ID Title 20751 Operate cross cut saw centre Defecting Strand Elective A minimum of 13 credits Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 7 of 15 2 Manufacturing > Solid Wood Manufacturing > Wood Product Manufacturing Skills ID Title Level Credit 24607 Wrap wood products manually Manufacturing > Wood Handling and Distribution > Timber Yarding ID Title 8005 Operate a mechanical timber stacking system 3 3 Level Credit 3 5 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 17971 20767 27074 Demonstrate knowledge of the solid wood manufacturing industry Demonstrate knowledge of saws and knives used in wood manufacturing Demonstrate knowledge of timber grading 2 5 2 5 2 5 Finger Jointing and Laminating Strand Meet the requirements of all of the following sets Finger Jointing and Laminating Strand Compulsory Finger Jointing and Laminating Strand Elective 1 Finger Jointing and Laminating Strand Elective 2 Finger Jointing and Laminating Strand Compulsory The following standards are required Manufacturing > Solid Wood Manufacturing > Wood Product Manufacturing Skills ID Title Level Credit 17964 Demonstrate knowledge of the wood product manufacturing industry 2 5 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 22978 Demonstrate knowledge of wood product quality 2 5 Level Credit 2 5 Finger Jointing and Laminating Strand Elective 1 A minimum of 5 credits Manufacturing > Solid Wood Manufacturing > Finger Jointing ID Title 15055 Demonstrate knowledge of the principles of finger jointing in solid wood manufacturing Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 8 of 15 2 Manufacturing > Solid Wood Manufacturing > Wood Product Manufacturing Skills ID Title Level Credit 15056 Demonstrate knowledge of the principles of laminating in wood product manufacturing 2 5 Level Credit 3 5 Level Credit 3 5 Level Credit 3 5 Finger Jointing and Laminating Strand Elective 2 A minimum of 15 credits Manufacturing > Solid Wood Manufacturing > Finger Jointing ID Title 4546 Feed and tail out finger jointer Manufacturing > Solid Wood Manufacturing > Sawmilling ID Title 20751 Operate cross cut saw centre Manufacturing > Wood Handling and Distribution > Timber Yarding ID Title 8005 Operate a mechanical timber stacking system Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 729 Measure moisture content of wood products 2 5 Pole, Post and Pile Strand Meet the requirements of all of the following sets Pole, Post and Pile Strand Compulsory Pole, Post and Pile Strand Elective Pole, Post and Pile Strand Compulsory The following standards are required Manufacturing > Solid Wood Manufacturing > Pole and Post Manufacturing ID Title Level 20022 Grade roundwood products Manufacturing > Solid Wood Manufacturing > Sawmilling ID Title 20751 Operate cross cut saw centre Competenz SSB Code 101571 Credit 3 5 Level Credit 3 5 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 9 of 15 2 Manufacturing > Wood Handling and Distribution > Timber Yarding ID Title 165 Handle, sort and stack timber Level Credit 2 3 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 17971 Demonstrate knowledge of the solid wood manufacturing industry 2 5 Pole, Post and Pile Strand Elective A minimum of 10 credits Agriculture, Forestry and Fisheries > Forestry > Forest Landing Operations ID Title Level 1252 Demonstrate knowledge of log making Agriculture, Forestry and Fisheries > Forestry > Forest Operations ID Title 6916 Demonstrate knowledge of the Approved Code of Practice relating to chainsaw use Credit 3 5 Level Credit 2 5 Agriculture, Forestry and Fisheries > Forestry > Non Commercial Forestry Skills ID Title Level Credit 6917 Demonstrate basic chainsaw operation 2 8 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 156 8008 Demonstrate knowledge of phytosanitary standards in the wood manufacturing industry Demonstrate knowledge of log yard operations 2 3 2 5 Saw Doctoring Principles Strand Meet the requirements of all of the following sets Saw Doctoring Principles Strand Compulsory Saw Doctoring Principles Strand Elective Saw Doctoring Principles Strand Compulsory The following standards are required Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 10 of 15 2 Manufacturing > Solid Wood Manufacturing > Saw Doctoring ID Title Level Credit 662 Grind and hone straight knives and anvils 3 5 669 Demonstrate knowledge of grinding for saw doctoring, timber machining and finger jointing Demonstrate knowledge of saw tooth profiles in saw doctoring Demonstrate knowledge of saw grinder application and operation 2 5 3 5 3 5 17962 17967 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 160 Demonstrate knowledge of the principles of sawmilling 2 5 20767 Demonstrate knowledge of saws and knives used in wood manufacturing 2 5 Level Credit Saw Doctoring Principles Strand Elective A minimum of 3 credits Manufacturing > Solid Wood Manufacturing > Saw Doctoring ID Title 656 Set circular saws 2 3 667 Maintain household and handyperson cutting tools 3 5 Sawmilling Strand Meet the requirements of all of the following sets Sawmilling Strand Compulsory Sawmilling Strand Elective Sawmilling Strand Compulsory The following standard is required Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 27074 Demonstrate knowledge of timber grading 2 5 Sawmilling Strand Elective A minimum of 10 credits Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 11 of 15 2 Manufacturing > Solid Wood Manufacturing > Sawmilling ID Title 20752 Operate ripping saw centre Manufacturing > Wood Handling and Distribution > Timber Yarding ID Title Level Credit 3 5 Level Credit 143 Fillet timber for further processing 2 3 164 Tally timber 2 3 165 Handle, sort and stack timber 2 3 8005 Operate a mechanical timber stacking system 3 5 17961 Tally random width timber 2 3 20757 Operate a mechanical timber handling system 3 5 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 156 160 17971 Demonstrate knowledge of phytosanitary standards in the wood manufacturing industry Demonstrate knowledge of the principles of sawmilling 2 3 2 5 Demonstrate knowledge of the solid wood manufacturing industry 2 5 Timber Drying and Treatment Strand Meet the requirements of all of the following sets Timber Drying and Treatment Strand Compulsory Timber Drying and Treatment Strand Elective Timber Drying and Treatment Strand Compulsory The following standards are required Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 729 Measure moisture content of wood products 2 5 17971 Demonstrate knowledge of the solid wood manufacturing industry 2 5 Timber Drying and Treatment Strand Elective A minimum of 10 credits Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 12 of 15 2 Health > Occupational Health and Safety > Occupational Health and Safety Practice ID Title Level Credit 21467 Store and handle workplace chemicals Manufacturing > Wood Handling and Distribution > Timber Yarding ID Title 165 Handle, sort and stack timber 3 8 Level Credit 2 3 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 162 16244 Demonstrate knowledge of the principles of wood drying Demonstrate knowledge of wood preservation 2 5 2 5 Level Credit 3 5 Timber Machining Strand Meet the requirements of all of the following sets Timber Machining Strand Compulsory Timber Machining Strand Elective Timber Machining Strand Compulsory The following standards are required Manufacturing > Solid Wood Manufacturing > Timber Machining ID Title 678 Feed and tail out a planer, and monitor planer performance Manufacturing > Solid Wood Manufacturing > Wood Product Manufacturing Skills ID Title Level Credit 17964 Demonstrate knowledge of the wood product manufacturing industry 2 5 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 15774 Demonstrate knowledge of timber machining 2 5 22978 Demonstrate knowledge of wood product quality 2 5 Timber Machining Strand Elective A minimum of 3 credits Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 13 of 15 2 Manufacturing > Solid Wood Manufacturing > Wood Product Manufacturing Skills ID Title Level Credit 24607 Wrap wood products manually Manufacturing > Wood Handling and Distribution > Timber Yarding ID Title 3 3 Level Credit 164 Tally timber 2 3 20757 Operate a mechanical timber handling system 3 5 Manufacturing > Wood Manufacturing - Generic Skills > Wood Manufacturing Foundation Skills ID Title Level Credit 162 729 Demonstrate knowledge of the principles of wood drying Measure moisture content of wood products 2 5 2 5 Transition Arrangements Version 1 Version 1 was issued following review of the National Certificate in Wood Manufacturing Foundation Skills (Level 2) with strands in Solid Wood Manufacturing, Sliced Veneer Operations, Technical Awareness, Wood Handling and Distribution, Wood Panel Manufacturing, and Wood Product Manufacturing [Ref: 1305]. The review found that wood fibre manufacturing qualifications should be separated from solid wood manufacturing qualifications. This qualification, the National Certificate in Wood Manufacturing Foundation Skills (Wood Panels) (Level 2) [Ref: 1691] and the National Certificate in Wood Manufacturing Foundation Skills (Wood Handling and Distribution) (Level 2) [Ref: 1692], replaced the National Certificate in Wood Manufacturing Foundation Skills (Level 2) with strands in Solid Wood Manufacturing, Sliced Veneer Operations, Technical Awareness, Wood Handling and Distribution, Wood Panel Manufacturing, and Wood Product Manufacturing [Ref: 1305]. There are substantial differences between the new and replaced qualifications. For detailed information see Review Summaries on the NZQA website. People currently working towards the Solid Wood Manufacturing or Wood Product Manufacturing strands of the replaced qualification may either complete the requirements for that qualification by 31 December 2014 or transfer their results to this qualification. Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 14 of 15 2 People currently working towards the Wood Panel Manufacturing strand of the replaced qualification may either complete the requirements of that qualification by 31 December 2014 or transfer their results to the National Certificate in Wood Manufacturing Foundation Skills (Wood Panels) (Level 2) [Ref: 1691]. People currently working towards the Wood Handling and Distribution strand of the replaced qualification may either complete the requirements of that qualification by 31 December 2014 or transfer their results to the National Certificate in Wood Manufacturing Foundation Skills (Wood Handling and Distribution) (Level 2) [Ref: 1692]. People currently working towards other strands of the replaced qualification may either complete the requirements for that qualification by 31 December 2014 or transfer their results to this qualification or one of the other replacement qualifications. The last date for entry to programmes or courses for the replaced qualification is 31 December 2011. People who are considering transition should contact their training provider or the Competenz at the address below for further advice. This qualification contains standards that replace or substitute earlier standards. For the purposes of this qualification, people who have gained credit for the earlier standards are exempt from the requirement to gain credit for the replacement or substitute standards – see table below. Credit for Exempt from 146 729 9774 27074 It is anticipated that no existing trainees will be disadvantaged by these transition arrangements. Any person who feels they have been disadvantaged by these transition arrangements should contact Competenz at the address below. Appeals will be considered on a case-by-case basis. Other standard setting bodies whose standards are included in the qualification New Zealand Industry Training Organisation Certification This certificate will display the logos of NZQA, Competenz and the organisation that has been granted consent to assess against standards that meet the requirements of the qualification (accredited). Competenz SSB Code 101571 New Zealand Qualifications Authority 2016 NZQF NQ Ref 1690 Version Page 15 of 15 2 Classification This qualification is classified according to the classification system listed on the Directory of Assessment Standards (DAS) and the New Zealand Standard Classification of Education (NZSCED) system as specified below. DAS Classification NZSCED Code Description Code Description 428 Manufacturing > Solid Wood Manufacturing 030304 Engineering and Related Technologies > Process and Resources Engineering > Wood Based Manufacturing Quality Management Systems Providers and Industry Training Organisations must be granted consent to assess by a recognised Quality Assurance Body before they can register credits from assessment against standards. Organisation with consent to assess and Industry Training Organisations assessing against standards must engage with the moderation system that applies to those standards. Consent to assess requirements and the moderation system are outlined in the associated Consent and Moderation Requirements (CMR) for each standard. Competenz SSB Code 101571 New Zealand Qualifications Authority 2016