ETSI TS 102 384 V10.3.0 (2015-08)
TECHNICAL SPECIFICATION
Smart Cards;
UICC-Terminal interface;
Card Application Toolkit (CAT) conformance specification
(Release 10)
Release 10
2
ETSI TS 102 384 V10.3.0 (2015-08)
Reference
RTS/SCP-00014va30
Keywords
smart card
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
Release 10
3
ETSI TS 102 384 V10.3.0 (2015-08)
Contents
Intellectual Property Rights ................................................................................................................................8
Foreword.............................................................................................................................................................8
Modal verbs terminology....................................................................................................................................8
Introduction ........................................................................................................................................................8
1
Scope ........................................................................................................................................................9
2
References ................................................................................................................................................9
2.1
2.2
3
3.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.4.1
3.2.4.2
3.2.4.3
3.3
3.4
3.5
3.5.1
3.6
Normative references ......................................................................................................................................... 9
Informative references ...................................................................................................................................... 10
Definitions and abbreviations .................................................................................................................10
Terminal definition and configurations ............................................................................................................ 10
Applicability ..................................................................................................................................................... 10
Applicability of the present document ........................................................................................................ 10
Applicability of the individual tests ............................................................................................................ 10
Applicability to terminal equipment ........................................................................................................... 11
Definitions .................................................................................................................................................. 11
Format of the table of optional features ................................................................................................ 11
Format of the applicability table ........................................................................................................... 11
Status and notations............................................................................................................................... 12
Table of optional features ................................................................................................................................. 12
Applicability table ............................................................................................................................................ 15
Conventions for mathematical notations .......................................................................................................... 56
Mathematical signs ..................................................................................................................................... 56
Abbreviations ................................................................................................................................................... 56
4
Test equipment .......................................................................................................................................56
5
Testing methodology in general .............................................................................................................57
5.1
5.2
5.3
Testing of optional functions and procedures................................................................................................... 57
Test interfaces and facilities ............................................................................................................................. 57
Information to be provided by the apparatus supplier ...................................................................................... 57
6
Void ........................................................................................................................................................58
7
Measurement uncertainty .......................................................................................................................58
8
Format of tests ........................................................................................................................................58
9
Generic call set up procedures................................................................................................................60
10
to 26 Void ...............................................................................................................................................60
27
Testing of the UICC/Terminal interface ................................................................................................60
27.0
General ............................................................................................................................................................. 60
27.1 to 27.21 Void ............................................................................................................................................................. 60
27.22
Card Application Toolkit.................................................................................................................................. 61
27.22.1a
General Test purpose .................................................................................................................................. 61
27.22.1b
Definition of default values for Card Application Toolkit testing .............................................................. 61
27.22.1
Initialization of Card Application Toolkit Enabled UICC by Card Application Toolkit Enabled
Terminal (Profile Download)...................................................................................................................... 64
27.22.1.1
Definition and applicability................................................................................................................... 64
27.22.1.2
Conformance requirement ..................................................................................................................... 64
27.22.1.3
Test purpose .......................................................................................................................................... 64
27.22.1.4
Method of test ....................................................................................................................................... 64
27.22.1.4.1
Initial conditions .............................................................................................................................. 64
27.22.1.4.2
Procedure ......................................................................................................................................... 64
27.22.1.5
Test requirement ................................................................................................................................... 65
27.22.2
Contents of the TERMINAL PROFILE command ..................................................................................... 65
27.22.2.1
Definition and applicability................................................................................................................... 65
ETSI
Release 10
4
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.2.2
Conformance requirement ..................................................................................................................... 65
27.22.2.3
Test purpose .......................................................................................................................................... 65
27.22.2.4
Method of test ....................................................................................................................................... 65
27.22.2.4.1
Initial conditions .............................................................................................................................. 65
27.22.2.4.2
Procedure ......................................................................................................................................... 65
27.22.2.5
Test requirement ................................................................................................................................... 66
27.22.3
Servicing of proactive UICC commands .................................................................................................... 66
27.22.3.1
Definition and applicability................................................................................................................... 66
27.22.3.2
Conformance requirement ..................................................................................................................... 66
27.22.3.3
Test purpose .......................................................................................................................................... 66
27.22.3.4
Method of test ....................................................................................................................................... 66
27.22.3.4.1
Initial conditions .............................................................................................................................. 66
27.22.3.4.2
Procedure ......................................................................................................................................... 66
27.22.3.5
Test requirement ................................................................................................................................... 66
27.22.4
Proactive UICC commands ........................................................................................................................ 67
27.22.4.1
DISPLAY TEXT................................................................................................................................... 67
27.22.4.1.1
DISPLAY TEXT (Normal) ............................................................................................................. 67
27.22.4.1.2
DISPLAY TEXT (Support of "No response from user") ................................................................ 76
27.22.4.1.3
DISPLAY TEXT (Display of extension text).................................................................................. 77
27.22.4.1.4
DISPLAY TEXT (Sustained text) ................................................................................................... 79
27.22.4.1.5
DISPLAY TEXT (Display of icons) ............................................................................................... 83
27.22.4.1.6
DISPLAY TEXT (UCS2 display supported in Cyrillic) ................................................................. 88
27.22.4.1.7
DISPLAY TEXT (Variable Time out) ............................................................................................ 89
27.22.4.1.8
DISPLAY TEXT (Support of Text Attribute) ................................................................................. 91
27.22.4.1.9
DISPLAY TEXT (UCS2 display in Chinese) ............................................................................... 117
27.22.4.1.10
DISPLAY TEXT (UCS2 display in Katakana) ............................................................................. 119
27.22.4.2
GET INKEY ....................................................................................................................................... 120
27.22.4.2.1
GET INKEY(normal) .................................................................................................................... 120
27.22.4.2.2
GET INKEY (No response from User) ......................................................................................... 127
27.22.4.2.3
GET INKEY (UCS2 display in Cyrillic) ....................................................................................... 128
27.22.4.2.4
GET INKEY (UCS2 entry in Cyrillic) .......................................................................................... 131
27.22.4.2.5
GET INKEY ("Yes/No" Response)............................................................................................... 133
27.22.4.2.6
GET INKEY (display of Icon) ...................................................................................................... 135
27.22.4.2.7
GET INKEY (Help Information)................................................................................................... 143
27.22.4.2.8
GET INKEY (Variable Time out) ................................................................................................. 146
27.22.4.2.9
GET INKEY (Support of Text Attribute) ...................................................................................... 148
27.22.4.2.10
GET INKEY (UCS2 display in Chinese) ...................................................................................... 179
27.22.4.2.11
GET INKEY (UCS2 entry in Chinese) ......................................................................................... 182
27.22.4.2.12
GET INKEY (UCS2 display in Katakana) .................................................................................... 183
27.22.4.2.13
GET INKEY (UCS2 entry in Katakana) ....................................................................................... 186
27.22.4.3
GET INPUT ........................................................................................................................................ 188
27.22.4.3.1
GET INPUT (normal).................................................................................................................... 188
27.22.4.3.2
GET INPUT (No response from User) .......................................................................................... 201
27.22.4.3.3
GET INPUT (UCS2 display in Cyrillic) ....................................................................................... 203
27.22.4.3.4
GET INPUT (UCS2 entry in Cyrillic) ........................................................................................... 206
27.22.4.3.5
GET INPUT (default text) ............................................................................................................. 209
27.22.4.3.6
GET INPUT (display of Icon) ....................................................................................................... 213
27.22.4.3.7
GET INPUT (Help Information) ................................................................................................... 220
27.22.4.3.8
GET INPUT (Support of Text Attribute) ...................................................................................... 222
27.22.4.3.9
GET INPUT (UCS2 display in Chinese) ....................................................................................... 258
27.22.4.3.10
GET INPUT (UCS2 entry in Chinese) .......................................................................................... 261
27.22.4.3.11
GET INPUT (UCS2 display in Katakana) ..................................................................................... 265
27.22.4.3.12
GET INPUT (UCS2 entry in Katakana) ........................................................................................ 268
27.22.4.4
MORE TIME ...................................................................................................................................... 271
27.22.4.4.1
Definition and applicability ........................................................................................................... 271
27.22.4.4.2
Conformance requirement ............................................................................................................. 271
27.22.4.4.3
Test purpose .................................................................................................................................. 271
27.22.4.4.4
Method of test ................................................................................................................................ 271
27.22.4.4.5
Test requirement ............................................................................................................................ 272
27.22.4.5
PLAY TONE....................................................................................................................................... 272
27.22.4.5.1
PLAY TONE (Normal) ................................................................................................................. 272
27.22.4.5.2
PLAY TONE (UCS2 display in Cyrillic) ...................................................................................... 284
ETSI
Release 10
27.22.4.5.3
27.22.4.5.4
27.22.4.5.5
27.22.4.5.6
27.22.4.6
27.22.4.6.1
27.22.4.6.2
27.22.4.6.3
27.22.4.6.4
27.22.4.6.5
27.22.4.7
27.22.4.7.1
27.22.4.8
27.22.4.8.1
27.22.4.8.2
27.22.4.8.3
27.22.4.8.4
27.22.4.8.5
27.22.4.8.6
27.22.4.8.7
27.22.4.8.8
27.22.4.8.9
27.22.4.9
27.22.4.9.1
27.22.4.9.2
27.22.4.9.3
27.22.4.9.4
27.22.4.9.5
27.22.4.9.6
27.22.4.9.7
27.22.4.9.8
27.22.4.9.9
27.22.4.9.10
27.22.4.9.11
27.22.4.9.12
27.22.4.10
27.22.4.11
27.22.4.12
27.22.4.13
27.22.4.14
27.22.4.15
27.22.4.15.1
27.22.4.15.2
27.22.4.15.3
27.22.4.15.4
27.22.4.15.5
27.22.4.16
27.22.4.16.1
27.22.4.17
27.22.4.17.1
27.22.4.18
27.22.4.18.1
27.22.4.18.2
27.22.4.19
27.22.4.19.1
27.22.4.19.2
27.22.4.20
27.22.4.20.1
27.22.4.20.2
27.22.4.21
27.22.4.21.1
27.22.4.21.2
5
ETSI TS 102 384 V10.3.0 (2015-08)
PLAY TONE (display of Icon) ..................................................................................................... 287
PLAY TONE (Support of Text Attribute) ..................................................................................... 294
PLAY TONE (UCS2 display in Chinese) ..................................................................................... 323
PLAY TONE (UCS2 display in Katakana) ................................................................................... 326
POLL INTERVAL .............................................................................................................................. 329
Definition and applicability ........................................................................................................... 329
Conformance requirement ............................................................................................................. 329
Test purpose .................................................................................................................................. 329
Method of test ................................................................................................................................ 329
Test requirement ............................................................................................................................ 331
REFRESH ........................................................................................................................................... 331
REFRESH (normal)....................................................................................................................... 331
SET UP MENU and ENVELOPE MENU SELECTION ................................................................... 333
SET UP MENU (normal) and ENVELOPE MENU SELECTION ............................................... 333
SET UP MENU (help request support) and ENVELOPE MENU SELECTION .......................... 344
SET UP MENU (next action support) and ENVELOPE MENU SELECTION ........................... 346
SET UP MENU (display of icons) and ENVELOPE MENU SELECTION ................................. 349
SET UP MENU (soft keys support) and ENVELOPE MENU SELECTION ............................... 354
SET UP MENU (support of Text Attribute) and ENVELOPE MENU SELECTION .................. 356
SET UP MENU (UCS2 display in Cyrillic) and ENVELOPE MENU SELECTION................... 392
SET UP MENU (UCS2 display in Chinese) and ENVELOPE MENU SELECTION .................. 397
SET UP MENU (UCS2 display in Katakana) and ENVELOPE MENU SELECTION ................ 401
SELECT ITEM ................................................................................................................................... 405
SELECT ITEM (mandatory features for Terminal supporting SELECT ITEM) .......................... 405
SELECT ITEM (next action support)............................................................................................ 418
SELECT ITEM (default item support) .......................................................................................... 419
SELECT ITEM (help request support) .......................................................................................... 421
SELECT ITEM (icons support) ..................................................................................................... 423
SELECT ITEM (presentation style) .............................................................................................. 427
SELECT ITEM (soft keys support) ............................................................................................... 430
SELECT ITEM (Support of "No response from user") ................................................................. 431
SELECT ITEM (Support of Text Attribute).................................................................................. 433
SELECT ITEM (UCS2 display in Cyrillic) ................................................................................... 467
SELECT ITEM (UCS2 display in Chinese) .................................................................................. 472
SELECT ITEM (UCS2 display in Katakana) ................................................................................ 474
SEND SHORT MESSAGE................................................................................................................. 478
Void..................................................................................................................................................... 478
Void..................................................................................................................................................... 478
SET UP CALL .................................................................................................................................... 478
POLLING OFF ................................................................................................................................... 478
PROVIDE LOCAL INFORMATION ................................................................................................ 478
Definition and applicability ........................................................................................................... 478
Conformance requirement ............................................................................................................. 478
Test purpose .................................................................................................................................. 478
Method of tests .............................................................................................................................. 479
Test requirement ............................................................................................................................ 487
SET UP EVENT LIST ........................................................................................................................ 487
SET UP EVENT LIST (normal) ................................................................................................... 487
PERFORM CARD APDU .................................................................................................................. 494
PERFORM CARD APDU (normal) .............................................................................................. 494
POWER OFF CARD .......................................................................................................................... 512
POWER OFF CARD (normal) ...................................................................................................... 512
POWER OFF CARD (detachable card reader) ............................................................................. 514
POWER ON CARD ............................................................................................................................ 515
POWER ON CARD (normal) ....................................................................................................... 515
POWER ON CARD (detachable card reader) ............................................................................... 519
GET READER STATUS .................................................................................................................... 520
GET READER STATUS (normal) ............................................................................................... 520
GET CARD READER STATUS (detachable card reader) ........................................................... 530
TIMER MANAGEMENT and ENVELOPE TIMER EXPIRATION ................................................ 532
TIMER MANAGEMENT (normal) .............................................................................................. 532
ENVELOPE TIMER EXPIRATION (normal) ............................................................................. 569
ETSI
Release 10
6
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4.22
SET UP IDLE MODE TEXT.............................................................................................................. 575
27.22.4.22.1
SET UP IDLE MODE TEXT (normal) ......................................................................................... 575
27.22.4.22.2
SET UP IDLE MODE TEXT (Icon support) ................................................................................ 584
27.22.4.22.3
SET UP IDLE MODE TEXT (UCS2 display in Cyrillic) ............................................................. 590
27.22.4.22.4
SET UP IDLE MODE TEXT (support of Text Attribute) ............................................................ 591
27.22.4.22.5
SET UP IDLE MODE TEXT (UCS2 display in Chinese) ............................................................ 618
27.22.4.22.6
SET UP IDLE MODE TEXT (UCS2 display in Katakana) .......................................................... 620
27.22.4.23
RUN AT COMMAND ........................................................................................................................ 621
27.22.4.23.1
RUN AT COMMAND (normal) ................................................................................................... 621
27.22.4.23.2
RUN AT COMMAND (Icon support) .......................................................................................... 624
27.22.4.23.3
RUN AT COMMAND (support of Text Attribute) ....................................................................... 630
27.22.4.23.4
RUN AT COMMAND (UCS2 display in Cyrillic) ....................................................................... 661
27.22.4.23.5
RUN AT COMMAND (UCS2 display in Chinese) ...................................................................... 662
27.22.4.23.6
RUN AT COMMAND (UCS2 display in Katakana) .................................................................... 664
27.22.4.24
SEND DTMF ...................................................................................................................................... 666
27.22.4.25
LANGUAGE NOTIFICATION ......................................................................................................... 666
27.22.4.25.1
Definition and applicability ........................................................................................................... 666
27.22.4.25.2
Conformance Requirement ............................................................................................................ 666
27.22.4.25.3
Test purpose .................................................................................................................................. 666
27.22.4.25.4
Method of Test .............................................................................................................................. 666
27.22.4.25.5
Test requirement ............................................................................................................................ 668
27.22.4.26
LAUNCH BROWSER ........................................................................................................................ 668
27.22.4.27
OPEN CHANNEL .............................................................................................................................. 668
27.22.4.27.1
Void ............................................................................................................................................... 668
27.22.4.27.2
Open Channel (related to GPRS)................................................................................................... 668
27.22.4.27.3
Open Channel (default bearer) ...................................................................................................... 668
27.22.4.27.4
Open Channel (Local Bearer) ........................................................................................................ 668
27.22.4.27.5
Open Channel (GPRS, support of Text Attribute) ......................................................................... 668
27.22.4.27.6
Open Channel (related to UICC Server Mode) ............................................................................. 669
27.22.4.27.7
Open Channel (related to Terminal Server Mode) ........................................................................ 671
27.22.4.28
CLOSE CHANNEL ............................................................................................................................ 679
27.22.4.28.1
CLOSE CHANNEL (related to GPRS) ......................................................................................... 679
27.22.4.28.2
CLOSE CHANNEL (support of Text Attribute) ........................................................................... 679
27.22.4.28.3
CLOSE CHANNEL (related to UICC Server Mode) .................................................................... 679
27.22.4.28.4
CLOSE CHANNEL (related to Terminal Server Mode) ............................................................... 682
27.22.4.29
RECEIVE DATA ................................................................................................................................ 684
27.22.4.30
SEND DATA ...................................................................................................................................... 684
27.22.4.31
GET CHANNEL STATUS ................................................................................................................. 685
27.22.4.31.1
GET CHANNEL STATUS (related to GPRS) .............................................................................. 685
27.22.4.31.2
GET CHANNEL STATUS (related to UICC server mode) .......................................................... 685
27.22.4.32
ACTIVATE......................................................................................................................................... 690
27.22.4.32.1
Definition and applicability ........................................................................................................... 690
27.22.4.32.2
Conformance Requirement ............................................................................................................ 690
27.22.4.32.3
Test purpose .................................................................................................................................. 690
27.22.4.32.4
Method of Test .............................................................................................................................. 690
27.22.4.32.5
Test requirement ............................................................................................................................ 692
27.22.4.33
CONTACTLESS STATE CHANGED ............................................................................................... 692
27.22.4.33.1
Definition and applicability ........................................................................................................... 692
27.22.4.33.2
Conformance Requirement ............................................................................................................ 692
27.22.4.33.3
Test purpose .................................................................................................................................. 692
27.22.4.33.4
Method of Test .............................................................................................................................. 692
27.22.4.33.5
Test requirement ............................................................................................................................ 694
27.22.5
Void .......................................................................................................................................................... 694
27.22.6
CALL CONTROL BY NAA .................................................................................................................... 694
27.22.6.1
Procedure for Terminal Originated calls ............................................................................................. 694
27.22.6.2
Void..................................................................................................................................................... 694
27.22.6.3
Interaction with Fixed Dialling Number (FDN) .................................................................................. 694
27.22.7
EVENT DOWNLOAD ............................................................................................................................. 694
27.22.7.1
MT Call Event ..................................................................................................................................... 694
27.22.7.2
Call Connected Event .......................................................................................................................... 694
27.22.7.2.1
Call Connected Event (MT and MO call)...................................................................................... 694
27.22.7.3
Call Disconnected Event ..................................................................................................................... 694
ETSI
Release 10
7
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.7.4
Location Status Event ......................................................................................................................... 694
27.22.7.4.1
Location Status Event (normal) ..................................................................................................... 694
27.22.7.5
User Activity Event ............................................................................................................................. 694
27.22.7.5.1
User Activity Event (normal) ........................................................................................................ 694
27.22.7.6
Idle screen available event .................................................................................................................. 696
27.22.7.6.1
Idle Screen Available (normal)...................................................................................................... 696
27.22.7.7
Card reader status event ...................................................................................................................... 698
27.22.7.7.1
Card Reader Status (normal) ......................................................................................................... 698
27.22.7.7.2
Card Reader Status(detachable card reader) .................................................................................. 703
27.22.7.8
Language selection event .................................................................................................................... 706
27.22.7.8.1
Language selection event (normal) ................................................................................................ 706
27.22.7.9
Browser termination event .................................................................................................................. 707
27.22.7.10
Data available event ............................................................................................................................ 707
27.22.7.10.1
Data available event (related to GPRS) ......................................................................................... 707
27.22.7.10.2
Data available event (related to UICC server mode) ..................................................................... 707
27.22.7.11
Channel Status event ........................................................................................................................... 710
27.22.7.11.1
Channel Status event (related to GPRS) ........................................................................................ 710
27.22.7.11.2
Channel Status event (related to UICC server mode) .................................................................... 711
27.22.7.12
Access Technology Change event ....................................................................................................... 714
27.22.7.13
Display parameter changed event ....................................................................................................... 714
27.22.7.14
Local Connection event....................................................................................................................... 714
27.22.7.15
Network search mode change event .................................................................................................... 714
27.22.7.16
Browsing status event ......................................................................................................................... 714
27.22.7.17
Frames Information changed event ..................................................................................................... 715
27.22.7.18
HCI connectivity event ....................................................................................................................... 715
27.22.7.18.1
HCI connectivity event (normal) ................................................................................................... 715
27.22.7.19
Contactless state request ..................................................................................................................... 717
27.22.7.19.1
Contactless state request (normal) ................................................................................................. 717
27.22.8
Void .......................................................................................................................................................... 720
27.22.9
Handling of command number ................................................................................................................. 720
27.22.9.1
Definition and applicability................................................................................................................. 720
27.22.9.2
Conformance requirement ................................................................................................................... 720
27.22.9.3
Test purpose ........................................................................................................................................ 720
27.22.9.4
Method of tests .................................................................................................................................... 720
27.22.9.4.1
Initial conditions ............................................................................................................................ 720
27.22.9.4.2
Procedure ....................................................................................................................................... 721
27.22.9.5
Test requirement ................................................................................................................................. 723
27.22.10
TERMINAL APPLICATIONS ................................................................................................................ 723
27.22.10.1
TERMINAL APPLICATIONS (one application) ............................................................................... 723
27.22.10.1.1
Definition and applicability ........................................................................................................... 723
27.22.10.1.2
Conformance requirement ............................................................................................................. 723
27.22.10.1.3
Test purpose .................................................................................................................................. 724
27.22.10.1.4
Method of test ................................................................................................................................ 724
27.22.10.2
TERMINAL APPLICATIONS (several applications) ........................................................................ 726
27.22.10.2.1
Definition and applicability ........................................................................................................... 726
27.22.10.2.2
Conformance requirement ............................................................................................................. 726
27.22.10.2.3
Test purpose .................................................................................................................................. 726
27.22.10.2.4
Method of test ................................................................................................................................ 726
Annex A (normative):
Details of Test-SIM (TestSIM)....................................................................729
Annex B (normative):
Details of terminal profile support .............................................................731
Annex C (informative):
Bibliography .................................................................................................742
Annex D (informative):
Change history .............................................................................................743
History ............................................................................................................................................................745
ETSI
Release 10
8
ETSI TS 102 384 V10.3.0 (2015-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Smart Card Platform (SCP).
It is based on work originally done in the 3GPP in TSG-terminals WG3.
The contents of the present document are subject to continuing work within TC SCP and may change following formal
TC SCP approval. If TC SCP modifies the contents of the present document, it will then be republished by ETSI with
an identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x
the first digit:
0
early working draft;
1
presented to TC SCP for information;
2
presented to TC SCP for approval;
3
or greater indicates TC SCP approved document under change control.
y
the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z
the third digit is incremented when editorial only changes have been incorporated in the document.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document defines the Card Application Toolkit (CAT) test conformance for the Terminal.
The aim of the present document is to ensure interoperability between an UICC and a Terminal independently of the
respective manufacturer, card issuer or operator.
Application specific tests for applications residing on an UICC are specified in ETSI TS 131 124 [9].
ETSI
Release 10
1
9
ETSI TS 102 384 V10.3.0 (2015-08)
Scope
The present document describes the technical characteristics and methods of test for testing the Card Application
Toolkit implemented in Terminals for the UICC, in compliance with the relevant requirements, and in accordance with
the relevant guidance given in ISO/IEC 9646-7 [3] and ETSI ETS 300 406 [4].
The present document covers the minimum characteristics considered necessary in order to provide sufficient
performance for Terminal and to prevent interference to other services or to other users.
It does not necessarily include all the characteristics which may be required by a user or subscriber, nor does it
necessarily represent the optimum performance achievable.
The present document is part of the ETSI-series of technical specifications. The present document neither replaces any
of the other ETSI technical specifications or ETSI related ETSs or ENs, nor is it created to provide full understanding of
(or parts of) the NAA. The present document lists the requirements, and provides the methods of test for testing the
Card Application Toolkit implemented in a Terminal for conformance to the ETSI standard.
For a full description of the system, reference should be made to all the ETSI technical specifications or ETSI related
ETSs or ENs. Clause 2 provides a complete list of the ETSI technical specifications, ETSI related ETSs, ENs, and
ETRs, on which this conformance test specifications is based.
If there is a difference between this present conformance document, and any other ETSI technical specification or ETSI
related ETS or EN, then the other ETSI technical specification or ETSI related ETS or EN is to be considered the
authoritative reference.
2
References
2.1
Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
•
In the case of a reference to a TC SCP document, a non specific reference implicitly refers to the latest version
of that document in the same Release as the present document.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE:
While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1]
ETSI TS 102 223: "Smart Cards; Card Application Toolkit (CAT)".
[2]
ISO/IEC 10646:2014: "Information technology -- Universal Coded Character Set (UCS)".
[3]
ISO/IEC 9646-7 (1995): "Information technology -- Open Systems Interconnection -Conformance testing methodology and framework -- Part 7: Implementation Conformance
Statements".
[4]
ETSI ETS 300 406 (1995): "Methods for Testing and Specification (MTS); Protocol and profile
conformance testing specifications; Standardization methodology".
[5]
ETSI TS 124 008: "Digital cellular telecommunications system (Phase 2+); Universal Mobile
Telecommunications System (UMTS); LTE; Mobile radio interface Layer 3 specification; Core
network protocols; Stage 3 (3GPP TS 24.008)".
[6]
ETSI TS 127 007: "Digital cellular telecommunications system (Phase 2+); Universal Mobile
Telecommunications System (UMTS); LTE; AT command set for User Equipment (UE)
(3GPP TS 27.007)".
ETSI
Release 10
10
ETSI TS 102 384 V10.3.0 (2015-08)
[7]
ISO/IEC 7816-3:2006: "Identification cards -- Integrated circuit cards -- Part 3: Cards with
contacts -- Electrical interface and transmission protocols".
[8]
ANSI TIA/EIA-41-D: "Cellular Radiotelecommunications Intersystem Operations
(ANSI/TIA/EIA-41-D-97)".
[9]
ETSI TS 131 124: "Universal Mobile Telecommunications System (UMTS); LTE; Mobile
Equipment (ME) conformance test specification; Universal Subscriber Identity Module
Application Toolkit (USAT) conformance test specification (3GPP TS 31.124)".
[10]
Void.
[11]
ETSI TS 101 267: "Digital cellular telecommunications system (Phase 2+); Specification of the
SIM Application Toolkit for the Subscriber Identity Module - Mobile Equipment (SIM-ME)
interface (3GPP TS 11.14 version 8.8.0 Release 1999)".
[12]
ETSI TS 100 607-4: "Digital cellular telecommunications system (Phase 2+); Mobile Station (MS)
conformance specification; Part 4: Subscriber Identity Module (SIM) application toolkit
conformance test specification (3GPP TS 11.10-4)".
[13]
ETSI TS 102 613: "Smart Cards; UICC - Contactless Front-end (CLF) Interface; Part 1: Physical
and data link layer characteristics".
[14]
ETSI TS 102 622: "Smart Cards; UICC - Contactless Front-end (CLF) Interface; Host Controller
Interface (HCI)".
[15]
ANSI/TIA/EIA-136-C: "TDMA Third Generation Wireless".
2.2
Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
•
In the case of a reference to a TC SCP document, a non specific reference implicitly refers to the latest version
of that document in the same Release as the present document.
NOTE:
While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1]
ETSI ETR 028: "Radio Equipment and Systems (RES); Uncertainties in the measurement of
mobile radio equipment characteristics".
3
Definitions and abbreviations
3.1
Terminal definition and configurations
The terminal definition and configurations specified in the present document apply.
3.2
Applicability
3.2.1
Applicability of the present document
The present document applies to a terminal equipment that supports the Card Application Toolkit optional feature
according to ETSI TS 102 223 [1].
3.2.2
Applicability of the individual tests
Table A.1 lists the optional features for which the supplier of the implementation states the support.
ETSI
Release 10
3.2.3
11
ETSI TS 102 384 V10.3.0 (2015-08)
Applicability to terminal equipment
The applicability to terminal equipment specified in table B.1 in clause 3.4 of the present document applies, unless
otherwise specified.
Terminals, which require a specific NAA to be present on the UICC, are to be tested according to the specific Card
Application Toolkit enabled NAA dependent test specification (e.g. ETSI TS 131 124 [9] for USIM application, ETSI
TS 100 607-4 [12] for SIM application). If there is no test specification defined for a specific Card Application Toolkit
enabled NAA, terminals may be tested according to the present document. In this case, the simulated UICC is to include
the specific NAA application, but the configuration and additional requirements of the specific Card Application
Toolkit enabled NAA are out of scope in the present document.
3.2.4
Definitions
3.2.4.1
Format of the table of optional features
Option
The optional feature supported or not by the implementation.
Support Answer notation
The support columns is to be filled in by the supplier of the implementation. The following common notations, defined
in ISO/IEC 9646-7 [3], are used for the support column in the tables below.
Y or y
supported by the implementation
N or n
not supported by the implementation
N/A, n/a or -
no answer required (allowed only if the status is N/A, directly or after evaluation of a conditional
status)
Mnemonic column
The Mnemonic column contains mnemonic identifiers for each item.
3.2.4.2
Format of the applicability table
The applicability of every test in table B.1 is formally expressed by the use of Boolean expression defined in the
following clause.
The columns in table B.1 have the following meaning:
•
In the "Item" column a local entry number for the requirement in the table is given.
•
In the "Description" column a short non-exhaustive description of the requirement is found.
•
The "Release" column gives the Release applicable and onwards, for the item in the "Description" column.
•
The "Test Sequence(s)" column gives a reference to the test sequence number(s) detailed in the present
document and required to validate the implementation of the corresponding item in the "Description" column.
•
For a given Release, the corresponding "Rel X Terminal" column lists the tests required for a Terminal to be
declared compliant to this Release.
•
The "Support" column is blank in the proforma, and is to be completed by the manufacturer in respect of each
particular requirement to indicate the choices, which have been made in the implementation.
•
The "Terminal Profile" column gives a reference to the corresponding bit that needs to be present in the
Terminal Profile.
ETSI
Release 10
12
3.2.4.3
ETSI TS 102 384 V10.3.0 (2015-08)
Status and notations
The "Release X Terminal" columns show the status of the entries as follows:
The following notations, defined in ISO/IEC 9646-7 [3], are used for the status column:
M
mandatory - the capability is required to be supported.
O
optional - the capability may be supported or not.
N/A
not applicable - in the given context, it is impossible to use the capability.
X
prohibited (excluded) - there is a requirement not to use this capability in the given context.
O.i
qualified optional - for mutually exclusive or selectable options from a set. "i" is an integer which
identifies an unique group of related optional items and the logic of their selection which is
defined immediately following the table.
Ci
conditional - the requirement on the capability ("M", "O", "X" or "N/A") depends on the support
of other optional or conditional items. "i" is an integer identifying an unique conditional status
expression which is defined immediately following the table. For nested conditional expressions,
the syntax "IF... THEN (IF... THEN... ELSE...) ELSE..." is to be used to avoid ambiguities.
References to items
For each possible item answer (answer in the support column) there exists a unique reference, used, for example, in the
conditional expressions. It is defined as the table identifier, followed by a solidus character "/", followed by the item
number in the table. If there is more than one support column in a table, the columns are to be discriminated by letters
(a, b, etc.), respectively.
EXAMPLE:
3.3
A.1/4 is the reference to the answer of item 4 in table A.1.
Table of optional features
Support of Card Application Toolkit is optional for Terminal. However, if a Terminal states conformance with a
specific SCP release, it is mandatory for the Terminal to support all functions of that release, as stated in table A.1.
The support of letter classes, which specify mainly Terminal hardware dependent features, is optional for the Terminal
and may supplement the Card Application Toolkit functionality described in the present document. If a Terminal states
conformance to a letter class, it is mandatory to support all functions within the respective letter class.
The supplier of the implementation is to state the support of possible options in table A.1.
Table A.1: Options
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Option
Capability Configuration parameter
Sustained text
UCS2 coding scheme for Entry
Extended Text String
Help information
Icons
Class A: Dual Slot
Detachable reader
Class B: RUN AT
Class C: LAUNCH BROWSER
Class D: Soft keys
Class E: B.I.P related to CSD
Screen sizing parameters
Screen Resizing
UCS2 coding scheme for Display
Terminal supporting GPRS
Terminal supporting UDP
Terminal supporting TCP
Redial in Set Up Call
Status
M
M
O
M
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
ETSI
Support
Mnemonic
O_Cap_Conf
O_sust_text
O_Ucs2_Entry
O_Ext_Str
O_Help
O_Icons
O_Dual_Slot
O_Detach_Rdr
O_Run_At
O_LB
O_Soft_key
O_BIP_CSD
O_Scr_Siz
O_Scr_Resiz
O_Ucs2_Disp
O_GPRS
O_UDP
O_TCP
O_Redial
Release 10
Item
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
13
Option
Status
Terminal decision to respond with "No response from
O
user" in finite time
Class E: B.I.P related to GPRS
O
Terminal supporting Called Party Subaddress
O
Immediate response
O
Variable Timeout
O
Void
Class F: B.I.P related to local bearer
O
BlueTooth Support
O
IrDA Support
O
RS232 Support
O
USB Support
O
WML Browser Support
O
XHTML Browser Support
O
HTML Browser Support
O
CHTML Browser Support
O
Class G: Battery Data
O
Class H: Multimedia Call support
O
Class I: Frame support
O
Class J: Multimedia Support
O
Void
Void
UCS2 in Cyrillic
O
UCS2 in Chinese
O
UCS2 in Katakana
O
Text attributes - Alignment left
O
Text attributes - Alignment center
O
Text attributes - Alignment right
O
Text attributes - Font size normal
O
Text attributes - Font size large
O
Text attributes - Font size small
O
Text attributes - Style normal
O
Text attributes - Style bold
O
Text attributes - Style italic
O
Text attributes - Style underlined
O
Text attributes - Style strikethrough
O
Text attributes - Style text foreground colour
O
Text attributes - Style text background colour
O
Terminal supporting "+CGMI" in combination with Run
O
AT Command
Class E: Terminal supports TCP, UICC in Server Mode
O
Terminal supports selection of default item in Select
O
Item
Preferred buffer size supported by the terminal for Open
O
Channel command is greater than 0 byte and less than
65535 bytes
Class E: Terminal supports TCP, Terminal in Server
O
Mode
Class E: Terminal supports UDP, Terminal in Server
O
Mode
Class K: Terminal Applications
O
Class L: Proactive command: ACTIVATE
O
Class M: Event download: HCI connectivity event
O
Class O: Broadcast Network Information
O
Terminal supports display capability
C001
Terminal supports keypad
C001
Terminal supports audio alerting
C001
Terminal supports speech call
C001
Terminal supports multiple languages
C001
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Support
Mnemonic
O_D_NoResp
O_BIP_GPRS
O_CP_Subaddr
O_Imm_Resp
O_Duration
O_BIP_Local
O_BT
O_IrDA
O_RS232
O_USB
O_WML
O_XHTML
O_HTML
O_CHTML
O_Batt
O_Xmedia_Call
O_Frames
O_MMS
O_UCS2_Cyrillic
O_UCS2_Chinese
O_UCS2_Katakana
O_TAT_AL
O_TAT_AC
O_TAT_AR
O_TAT_FSN
O_TAT_FSL
O_TAT_FSS
O_TAT_SN
O_TAT_SB
O_TAT_SI
O_TAT_SU
O_TAT_SS
O_TAT_STFC
O_TAT_STFB
O_+CGMI
O_TCP_UICC_ServerMode
O_Select_Item_Default_Item
O_BUFFER_SIZE
O_TCP_Terminal_ServerMode
O_UDP_Terminal_ServerMode
O_Terminal_Applications
O_Activate
O_HCI_Connectivity_Event
O_Broadcast_Network
O_ No_Type_ND
O_No_Type_NK
O_No_Type_NA
O_No_Type_NS
O_No_Type_NL
Release 10
Item
72
73
74
C001
14
ETSI TS 102 384 V10.3.0 (2015-08)
Option
Status Support
Class R: Contactless State Change/Request
O
Confirmation parameters supported for OPEN
O
CHANNEL - Terminal Server Mode
Direct communication channel supported for OPEN
O
CHANNEL - Terminal Server Mode
If feature is implemented according to Rel-8 or later then O, else M.
ETSI
Mnemonic
O_CL_State_CR
O_Terminal_ServerMode_Confir
m_Param
O_Direct_Com_Channel
Release 10
3.4
15
ETSI TS 102 384 V10.3.0 (2015-08)
Applicability table
Table B.1a: Applicability of tests (releases 4 to 8)
Item
1
2
3
4
Description
PROFILE DOWNLOAD
27.22.1
Contents of the TERMINAL PROFILE
command
27.22.2
Servicing of Proactive UICC
Commands
27.22.3
DISPLAY TEXT
27.22.4.1
Unpacked
Screen busy
high priority
Packed
Clear after delay
Long text up to 160 bytes
Backwards move in Proactive UICC
session
Session terminated by user
Release
Rel-4
Rel-4
Test
sequence(s)
1
Rel-4
Rel-4
Terminal
M
M
Rel-5
Terminal
M
M
Rel-6
Terminal
M
M
Rel-7
Terminal
M
M
Rel-8
Terminal
M
M
M
M
M
M
M
Rel-4
Rel-4
Rel-4
Rel-4
Rel-4
Rel-4
Rel-4
1.1
1.2
1.3
1.4
1.5
1.6
1.7
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Rel-4
1.8
M
M
M
M
Command not understood by Terminal
No response from user
Rel-4
Rel-4
1.9
2.1
M
C120
M
C120
M
C120
M
C120
Extension Text
Rel-4
3.1
M
M
M
M
C170
C170
C170
C170
C170
C170
C170 AND
C171
C170 AND
C171
C170
C120 AND
C170 AND
C171
C170
Sustained text
Rel-4
4.1, 4.2
M
M
M
M
C170
Sustained text
Rel-4
4.3
M
M
M
M
C170 AND
C171
Icons
Rel-4
5.1, 5.2, 5.3
C108
C108
C108
C108
UCS2 display in Cyrillic
Rel-4
6.1
C118
C118
C118
C118
Variable Timeout
Rel-4
7.1
C126
C126
C126
C126
Text attribute - left alignment
Rel-5
8.1
C146
C146
C146
C108 AND
C170 AND
C171
C118 AND
C170 AND
C171
C126 AND
C170 AND
C171
C146 AND
C170 AND
C171
ETSI
Terminal
Profile
E.1/1
E.1/1
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/110
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/16
AND E.1/110
E.1/17 AND E.1/65
AND E.1/110
E.1/17 AND E.1/65
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/137
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/124
AND E.1/217 AND
E.1/110 AND E.1/111
Support
Release 10
Item
16
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Text attribute - center alignment
Rel-5
Test
sequence(s)
8.2
Rel-4
Terminal
Text attribute - right alignment
Rel-5
8.3
Text attribute - large font size
Rel-5
8.4
C150
C150
C150
AND C149 AND C149 AND C149
Text attribute - small font size
Rel-5
8.5
C151
C151
C151
AND C149 AND C149 AND C149
Text attribute - bold on
Rel-5
8.6
C153
C153
C153
AND C152 AND C152 AND C152
Text attribute - italic on
Rel-5
8.7
C154
C154
C154
AND C152 AND C152 AND C152
Text attribute - underlined on
Rel-5
8.8
C155
C155
C155
AND C152 AND C152 AND C152
Text attribute -strikethrough on
Rel-5
8.9
C156
C156
C156
AND C152 AND C152 AND C152
Text attribute - foreground and
background colours
Rel-5
8.10
C157
C157
C157
AND C158 AND C158 AND C158
UCS2 display_in Chinese
Rel-4
9.1
C143
C143
C143
UCS2 display_in Katakana
Rel-4
10.1
C145
C145
C145
Frames
Rel-6
TBD
C133
C133
ETSI
Rel-5
Terminal
C147
Rel-6
Terminal
C147
Rel-7
Terminal
C147
C148
C148
C148
Rel-8
Terminal
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170
Terminal
Profile
E.1/17 AND E.1/124
AND E.1/218 AND
E.1/110 AND E.1/111
E.1/17 AND E.1/124
AND E.1/219 AND
E.1/110 AND E.1/111
E.1/17 AND E.1/124
AND E.1/221 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/222 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/226 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/227 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/225 AND
E.1/228 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/229 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/230 AND
E.1/231 AND E.1/110
AND E.1/111
E.1/17 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/177
AND E.1/178 AND
E.1/110
Support
Release 10
Item
5
17
Description
ETSI TS 102 384 V10.3.0 (2015-08)
Release
Test
sequence(s)
Rel-4
Terminal
Rel-5
Terminal
Rel-6
Terminal
Rel-7
Terminal
Rel-8
Terminal
Terminal
Profile
Rel-4
1.1
M
M
M
M
Prompt packed
Rel-4
1.2
M
M
M
M
Backwards move in UICC session
Rel-4
1.3
M
M
M
M
Session terminated by user
Rel-4
1.4
M
M
M
M
SMS alphabet
Rel-4
1.5
M
M
M
M
Long text up to 160 bytes
Rel-4
1.6
M
M
M
M
No response from user
Rel-4
2.1
C120
C120
C120
C120
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
UCS2 display in Cyrillic
Rel-4
3.1
C118
C118
C118
C118
UCS2 display in Cyrillic, Long text up to
70 chars
Rel-4
3.2
C118
C118
C118
C118
UCS2 format of entry in Russian
Rel-4
4.1
C105
C105
C105
C105
"Yes/No" response
Rel-4
5.1
M
M
M
M
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C120 AND
C170 AND
C171
C118 AND
C170 AND
C171
C118 AND
C170 AND
C171
C105 AND
C170 AND
C171
C170 AND
C171
Icons
Rel-4
6.1, 6.2, 6.3,
6.4
C108
C108
C108
C108
Help information
Rel-4
7.1
C107
C107
C107
C107
Variable Timeout
Rel-4
8.1
C126
C126
C126
C126
Text attribute - left alignment
Rel-5
9.1
C146
C146
C146
Text attribute - center alignment
Rel-5
9.2
C147
C147
C147
GET INKEY
Prompt unpacked
27.22.4.2
ETSI
C108 AND
C170 AND
C171
C107 AND
C170 AND
C171
C126 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/60
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/140
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/124
AND E.1/217 AND
E.1/110 AND E.1/111
E.1/18 AND E.1/124
AND E.1/218 AND
E.1/110 AND E.1/111
Support
Release 10
Item
18
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Text attribute - right alignment
Rel-5
Test
sequence(s)
9.3
Rel-4
Terminal
Rel-5
Terminal
C148
Text attribute - large font size
Rel-5
9.4
C150
C150
C150
AND C149 AND C149 AND C149
Text attribute - small font size
Rel-5
9.5
C151
C151
C151
AND C149 AND C149 AND C149
Text attribute - bold on
Rel-5
9.6
C153
C153
C153
AND C152 AND C152 AND C152
Text attribute - italic on
Rel-5
9.7
C154
C154
C154
AND C152 AND C152 AND C152
Text attribute -underlined on
Rel-5
9.8
C155
C155
C155
AND C152 AND C152 AND C152
Text attribute -strikethrough on
Rel-5
9.9
C156
C156
C156
AND C152 AND C152 AND C152
Text attribute - foreground and
background colours
Rel-5
9.10
C157
C157
C157
AND C158 AND C158 AND C158
UCS2 display in Chinese
Rel-4
10.1, 10.2
C143
C143
C143
UCS2 format of entry in Chinese
Rel-4
11.1
C142
C142
C142
UCS2 display in Katakana
Rel-4
12.1
C145
C145
C145
UCS2 format of entry in Katagana
Rel-4
13.1
C144
C144
C144
ETSI
Rel-6
Terminal
C148
Rel-7
Terminal
C148
Rel-8
Terminal
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C142 AND
C170 AND
C171
C145 AND
C170 AND
C171
C144 AND
C170 AND
C171
Terminal
Profile
E.1/18 AND E.1/124
AND E.1/219 AND
E.1/110 AND E.1/111
E.1/18 AND E.1/124
AND E.1/221 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/222 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/226 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/227 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/228 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/18 AND
E.1/124AND E.1/229
AND E.1/225 AND
E.1/110 AND E.1/111
E.1/18 AND E.1/124
AND E.1/230 AND
E.1/231 AND E.1/110
AND E.1/111
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/14
AND E.1/110 AND
E.1/111
Support
Release 10
Item
19
Description
Release
Rel-4
Terminal
Rel-5
Terminal
Rel-6
Test
sequence(s)
TBD
Rel-6
Terminal
C133
Rel-7
Terminal
C133
Rel-8
Terminal
C133 AND
C170 AND
C171
Terminal
Profile
E.1/19 AND E.1/177
AND E.1/178 AND
E.1/110 AND E.1/111
Rel-4
1.1
M
M
M
M
Input packed
Rel-4
1.2
M
M
M
M
SMS alphabet
Rel-4
1.3
M
M
M
M
Hidden input
Rel-4
1.4
M
M
M
M
Min/max acceptable length
Rel-4
1.5
M
M
M
M
Backwards move in UICC session
Rel-4
1.6
M
M
M
M
Session terminated by user
Rel-4
1.7
M
M
M
M
Prompt text up to 160 bytes
Rel-4
1.8
M
M
M
M
SMS default alphabet, Terminal to echo
text, packing not required
Null length for the text string
Rel-4
1.9
M
M
M
M
Rel-4
1.10
M
M
M
M
No response from user
Rel-4
2.1
C120
C120
C120
C120
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
UCS2 display in Cyrillic
Rel-4
3.1, 3.2
C118
C118
C118
C118
UCS2 entry in Cyrillic
Rel-4
4.1, 4.2
C105
C105
C105
C105
Default text for the input
Rel-4
5.1, 5.2
M
M
M
M
Icons
Rel-4
6.1, 6.2, 6.3,
6.4
C108
C108
C108
C108
Help information
Rel-4
7.1
C107
C107
C107
C107
Text attribute - left alignment
Rel-5
8.1
C146
C146
C146
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C120 AND
C170 AND
C171
C118 AND
C170 AND
C171
C105 AND
C170 AND
C171
C170 AND
C171
C108 AND
C170 AND
C171
C107 AND
C170 AND
C171
C146 AND
C170 AND
C171
Frames
6
ETSI TS 102 384 V10.3.0 (2015-08)
GET INPUT
Input unpacked
27.22.4.3
ETSI
E.1/19 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/217 AND
E.1/110 AND E.1/111
Support
Release 10
Item
20
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Text attribute - center alignment
Rel-5
Test
sequence(s)
8.2
Rel-4
Terminal
Text attribute - right alignment
Rel-5
8.3
Text attribute - large font size
Rel-5
8.4
C150
C150
C150
AND C149 AND C149 AND C149
Text attribute - small font size
Rel-5
8.5
C151
C151
C151
AND C149 AND C149 AND C149
Text attribute - bold on
Rel-5
8.6
C153
C153
C153
AND C152 AND C152 AND C152
Text attribute - italic on
Rel-5
8.7
C154
C154
C154
AND C152 AND C152 AND C152
Text attribute -underlined on
Rel-5
8.8
C155
C155
C155
AND C152 AND C152 AND C152
Text attribute -strikethrough on
Rel-5
8.9
C156
C156
C156
AND C152 AND C152 AND C152
Text attribute - foreground and
background colours
Rel-5
8.10
C157
C157
C157
AND C158 AND C158 AND C158
UCS2 display in Chinese
Rel-4
9.1, 9.2
C143
C143
C143
C143
UCS2 entry in Chinese
Rel-4
10.1, 10.2
C142
C142
C142
C142
UCS2 display in Katakana
Rel-4
11.1, 11.2
C145
C145
C145
C145
ETSI
Rel-5
Terminal
C147
Rel-6
Terminal
C147
Rel-7
Terminal
C147
C148
C148
C148
Rel-8
Terminal
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C142 AND
C170 AND
C171
C145 AND
C170 AND
C171
Terminal
Profile
E.1/19 AND E.1/124
AND E.1/218 AND
E.1/110 AND E.1/111
E.1/19 AND E.1/124
AND E.1/219 AND
E.1/110 AND E.1/111
E.1/19 AND E.1/124
AND E.1/221 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/222 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/226 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/227 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/228 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/229 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/230 AND
E.1/231 AND E.1/110
AND E.1/111
E.1/19 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/15
AND E.1/110 AND
E.1/111
Support
Release 10
Item
7
8
21
Description
UCS2 entry in Katakana
Rel-4
Test
sequence(s)
12.1, 12.2
Frames
Rel-6
TBD
Rel-4
1.1
M
M
M
M
Rel-4
1.1
M
M
M
M
UCS2 display in Cyrillic
Rel-4
2.1
C118
C118
C118
C118
Icons
Rel-4
3.1, 3.2,3.3,
3.4
C108
C108
C108
C108
Text attribute - left alignment
Rel-5
4.1
C146
C146
C146
Text attribute - center alignment
Rel-5
4.2
C147
C147
C147
Text attribute - right alignment
Rel-5
4.3
C148
C148
C148
Text attribute - large font size
Rel-5
4.4
C150
C150
C150
AND C149 AND C149 AND C149
Text attribute - small font size
Rel-5
4.5
C151
C151
C151
AND C149 AND C149 AND C149
Text attribute - bold on
Rel-5
4.6
C153
C153
C153
AND C152 AND C152 AND C152
Text attribute - italic on
Rel-5
4.7
C154
C154
C154
AND C152 AND C152 AND C152
MORE TIME
PLAY TONE
Play all tones
Release
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4.4
27.22.4.5
Rel-4
Terminal
C144
Rel-5
Terminal
C144
ETSI
Rel-6
Terminal
C144
Rel-7
Terminal
C144
C133
C133
Rel-8
Terminal
C144 AND
C170 AND
C171
C133 AND
C170 AND
C171
M
Terminal
Profile
E.1/19 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/177
AND E.1/178 AND
E.1/110 AND E.1/111
E.1/20
C170 AND
C171 AND
C172
C118 AND
C170 AND
C172
C108 AND
C170 AND
C172
C146 AND
C170 AND
C172
C147 AND
C170 AND
C172
C148 AND
C170 AND
C172
C150 AND
C149 AND
C170 AND
C172
C151 AND
C149 AND
C170 AND
C172
C153 AND
C152 AND
C170 AND
C172
C154 AND
C152 AND
C170 AND
C172
E.1/21 AND E1/110
AND E.1/111
E.1/21
AND E.1/15 AND
E1/110
E.1/21 AND E1/110
E.1/21 AND E.1/124
AND E.1/217 AND
E1/110
E.1/21 AND E.1/124
AND E.1/218 AND
E1/110
E.1/21 AND E.1/124
AND E.1/219 AND
E1/110
E.1/21 AND E.1/124
AND E.1/221 AND
E.1/220 AND E1/110
E.1/21 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
E.1/21 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
E.1/21 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
Support
Release 10
Item
9
10
11
22
Description
Text attribute -underlined on
Rel-5
Test
sequence(s)
4.8
Text attribute -strikethrough on
Rel-5
4.9
Text attribute - foreground and
background colours
Rel-5
4.10
UCS2 display in Chinese
Rel-4
5.1
UCS2 display in Katakana
Rel-4
6.1
Frames
Rel-6
TBD
Themed and Melody tones
Rel-6
TBD
Rel-4
1.1
Rel-4
N/A
Rel-4
Rel-4
1.2
N/A
Rel-4
Rel-4
Rel-4
Rel-4
N/A
1.5
N/A
N/A
Rel-4
POLL INTERVAL
27.22.4.6
Duration
REFRESH
27.22.4.7
NAA Initialization and Full File Change
Notification
File Change Notification
NAA Initialization and File Change
Notification
NAA Initialization
UICC Reset
NAA Application Reset
NAA Session Reset
SET UP MENU
27.22.4.8
Set up, menu selection, replace and
remove menu
Large menu
Help information
Release
Rel-4
Terminal
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-5
Rel-6
Rel-7
Rel-8
Terminal
Terminal
Terminal
Terminal
C155
C155
C155
C155 AND
AND C152 AND C152 AND C152 C152 AND
C170 AND
C172
C156
C156
C156
C156 AND
AND C152 AND C152 AND C152 C152 AND
C170 AND
C172
C157
C157
C157
C157 AND
AND C158 AND C158 AND C158 C158 AND
C170 AND
C172
C143
C143
C143
C143 AND
C170 AND
C172
C145
C145
C145
C145 AND
C170 AND
C172
C133
C133
C133 AND
C170 AND
C172
C138
C138
C138 AND
C170 AND
C172
M
M
M
M
M
Terminal
Profile
E.1/21 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
E.1/21 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
E.1/21 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
E.1/21
AND E.1/15 AND
E1/110
E.1/21
AND E.1/15 AND
E1/110
E.1/21 AND E.1/177
AND E.1/178 AND
E1/110
E.1/21 AND E1/110
E.1/22
E.1/24
M
M
M
M
M
M
M
M
M
M
1.1
M
M
M
M
Rel-4
1.2
M
M
M
M
Rel-4
2.1
C107
C107
C107
C107
ETSI
E.1/24
E.1/24
E.1/24
E.1/24
E.1/24
E.1/24
C170 AND E.1/30 AND E.1/4 AND
C171
E1/110 AND E1/111
C170 AND E.1/30 AND E.1/4 AND
C171
E1/110 AND E1/111
C107 AND E.1/30 AND E.1/4 AND
C170 AND
E1/110 AND E1/111
C171
Support
Release 10
Item
23
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Next action indicator
Rel-4
Test
sequence(s)
3.1
Rel-4
Terminal
M
Rel-5
Terminal
M
Rel-6
Terminal
M
Rel-7
Terminal
M
Icons
Rel-4
4.1, 4.2
C108
C108
C108
C108
Soft key access
Rel-4
5.1
C112
C112
C112
C112
Text attribute
Rel-5
6.1
C146
C146
C146
Text attribute - center alignment
Rel-5
6.2
C147
C147
C147
Text attribute - right alignment
Rel-5
6.3
C148
C148
C148
Text attribute - large font size
Rel-5
6.4
C150
C150
C150
AND C149 AND C149 AND C149
Text attribute - small font size
Rel-5
6.5
C151
C151
C151
AND C149 AND C149 AND C149
Text attribute - bold on
Rel-5
6.6
C153
C153
C153
AND C152 AND C152 AND C152
Text attribute - italic on
Rel-5
6.7
C154
C154
C154
AND C152 AND C152 AND C152
Text attribute -underlined on
Rel-5
6.8
C155
C155
C155
AND C152 AND C152 AND C152
Text attribute -strikethrough on
Rel-5
6.9
C156
C156
C156
AND C152 AND C152 AND C152
Text attribute - foreground and
background colours
Rel-5
6.10
C157
C157
C157
AND C158 AND C158 AND C158
ETSI
Rel-8
Terminal
C170 AND
C171
C108 AND
C170 AND
C171
C112 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
Terminal
Profile
E.1/30 AND E1/110
AND E1/111
E.1/30 AND E1/110
AND E1/111
E.1/30 AND E.1/74
AND E1/110 AND
E1/111
E.1/30 AND E.1/124
AND E.1/217 AND
E1/110 AND E1/111
E.1/30 AND E.1/124
AND E.1/218 AND
E1/110 AND E1/111
E.1/30 AND E.1/124
AND E.1/219 AND
E1/110 AND E1/111
E.1/30 AND E.1/124
AND E.1/221 AND
E.1/220 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
AND E1/111
Support
Release 10
Item
12
24
Description
UCS2 Display in Cyrillic
Rel-4
Test
sequence(s)
7.1
UCS2 Display in Chinese
Rel-4
8.1
C143
C143
C143
UCS2 Display in Katakana
Rel-4
9.1
C145
C145
C145
Rel-4
1.1
M
M
M
M
Large menu
Rel-4
1.2, 1.3, 1.6
M
M
M
M
Backwards move
Rel-4
1.4
M
M
M
M
User termination
Rel-4
1.5
M
M
M
M
Next action indicator
Rel-4
2.1
M
M
M
M
Default selected item
Rel-4
3.1
M
M
M
M
Help information
Rel-4
4.1
C107
C107
C107
C107
Icons
Rel-4
5.1, 5.2
C108
C108
C108
C108
Presentation style
Rel-4
6.1, 6.2
M
M
M
M
Soft keys
Rel-4
7.1
C112
C112
C112
C112
No Response from user
Rel-4
8.1
C120
C120
C120
C120
Text attribute - left alignment
Rel-5
9.1
C146
C146
C146
Text attribute - center alignment
Rel-5
9.2
C147
C147
C147
SELECT ITEM
Mandatory features
Release
Rel-4
Terminal
C118
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-5
Terminal
C118
Rel-6
Terminal
C118
Rel-7
Terminal
C118
Rel-8
Terminal
C118 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
Terminal
Profile
E.1/39
AND E.1/15 AND
E1/110 AND E1/111
E.1/39
AND E.1/15 AND
E1/110 AND E1/111
E.1/39
AND E.1/15 AND
E1/110 AND E1/111
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C107 AND
C170 AND
C171
C108 AND
C170 AND
C171
C170 AND
C171
C112 AND
C170 AND
C171
C120 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
27.22.4.9
ETSI
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E.1/73
AND E1/110 AND
E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/217 AND
E1/110 AND E1/111
E.1/25 AND E.1/124
AND E.1/218 AND
E1/110 AND E1/111
Support
Release 10
Item
13
14
25
Description
Text attribute - right alignment
Rel-5
Test
sequence(s)
9.3
Text attribute - large font size
Rel-5
9.4
C150
C150
C150
AND C149 AND C149 AND C149
Text attribute - small font size
Rel-5
9.5
C151
C151
C151
AND C149 AND C149 AND C149
Text attribute - bold on
Rel-5
9.6
C153
C153
C153
AND C152 AND C152 AND C152
Text attribute - italic on
Rel-5
9.7
C154
C154
C154
AND C152 AND C152 AND C152
Text attribute -underlined on
Rel-5
9.8
C155
C155
C155
AND C152 AND C152 AND C152
Text attribute -strikethrough on
Rel-5
9.9
C156
C156
C156
AND C152 AND C152 AND C152
Text attribute - foreground and
background colours
Rel-5
9.10
C157
C157
C157
AND C158 AND C158 AND C158
UCS2 Display in Cyrillic
Rel-4
10.1,10.2,10.
3
UCS2 Display in Chinese
Rel-4
UCS2 Display in Katakana
Frames
SEND SMS
Void
Release
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4.10
Rel-4
Terminal
Rel-5
Terminal
C148
C118
Rel-6
Terminal
C148
Rel-7
Terminal
C148
C118
C118
C118
11.1
C143
C143
C143
Rel-4
12.1,12.2,12.
3
C145
C145
C145
Rel-6
TBD
C133
C133
Rel-4
N/A
ETSI
Rel-8
Terminal
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C118 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170 AND
C171
Terminal
Profile
E.1/25 AND E.1/124
AND E.1/219 AND
E1/110 AND E1/111
E.1/25 AND E.1/124
AND E.1/221 AND
E.1/220 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
AND E1/111
E.1/25
AND E.1/15 AND
E1/110 AND E1/111
E.1/25
AND E.1/15 AND
E1/110 AND E1/111
E.1/25
AND E.1/15 AND
E1/110 AND E1/111
E.1/25 AND E.1/177
AND E.1/178 AND
E1/110 AND E1/111
E.1/26
Support
Release 10
26
Item
Description
15
16
17
18
Void
27.22.4.12
SET UP CALL
27.22.4.13
POLLING OFF
27.22.4.14
PROVIDE LOCAL INFO
27.22.4.15
Location Information according to current
NAA
IMEI of the Terminal
Network Measurement results according
to current NAA
Date, time and time zone
Language setting
Void
Access Technology
ESN of the terminal
IMEISV of the terminal
Search Mode
Charge State of the Battery
Void
Broadcast Network information
SET UP EVENT LIST
27.22.4.16
User Activity event
19
20
ETSI TS 102 384 V10.3.0 (2015-08)
Release
Test
sequence(s)
Rel-4
Terminal
Rel-5
Terminal
Rel-6
Terminal
Rel-7
Terminal
Rel-4
Rel-4
N/A
1.1
M
M
M
M
Rel-4
N/A
Rel-4
Rel-4
1.2
N/A
M
M
M
M
M
E.1/31
E.1/32 AND E.1/67
Rel-4
Rel-4
1.4
1.5
M
M
M
M
M
M
M
M
M
M
E.1/59
E.1/68
Rel-4
Rel-4
Rel-6
Rel-6
Rel-6
N/A
1.8
1.9
N/A
1.11
M
M
M
M
M
M
M
M
C139
C139
C139
E.1/72
E.1/141
E.1/143
E.1/144
E.1/170
Rel-8
1.13
C169
E.1/239
Rel-4
1.1
M
M
M
M
C171
Replace by new event list
Rel-4
1.2
M
M
M
M
Remove event
Rel-4
1.3
M
M
M
M
Remove Event on Terminal Power Cycle
Rel-4
1.4
M
M
M
M
C170 AND
C171 AND
C174
C170 AND
C171 AND
C174
C170 AND
C171 AND
C174
E.1/33 AND E.1/35
AND E1/111
E.1/33 AND E.1/35
AND E.1/36 AND
E1/110 AND E1/111
E.1/33 AND E.1/35
AND E1/110 AND
E1/111
E.1/33 AND E.1/35
AND E1/110 AND
E1/111
Rel-4
1.1
C109
C109
C109
C109
C109
E.1/51
Rel-4
1.2
C109
C109
C109
C109
C109
E.1/51
Rel-4
1.3
C109
C109
C109
C109
C109
E.1/51
Rel-4
Rel-4
Rel-4
1.4
1.5
2.1
C109
C109
C116
C109
C109
C116
C109
C109
C116
C109
C109
C116
C109
C109
C116
E.1/51
E.1/51
E.1/51
PERFORM CARD APDU 27.22.4.17
Additional card inserted, Select MF and
Get Response
Additional card inserted, Select DF GSM,
Select EF PLMN , Update Binary, Read
Binary on EF PLMN
Additional card inserted, card powered
off
No card inserted, card powered off
Invalid card reader identifier
Detachable reader
Rel-8
Terminal
Terminal
Profile
E.1/29
E.1/23
E.1/31
ETSI
Support
Release 10
27
Item
Description
21
POWER OFF CARD
27.22.4.18
Additional card inserted
No card inserted
Detachable reader
POWER ON CARD
27.22.4.19
Additional card inserted
No ATR
No card inserted
Detachable reader
GET READER STATUS
27.22.4.20
Additional card inserted, card powered
Additional card inserted, card not
powered
Additional card inserted, card not present
Detachable reader
TIMER MANAGEMENT 27.22.4.21.1
Start timer 1 several times, get the
current value of the timer and deactivate
the timer successfully
Start timer 2 several times, get the
current value of the timer and deactivate
the timer successfully
Start timer 8 several times, get the
current value of the timer and deactivate
the timer successfully
Try to get the current value of a timer
which is not started: action in
contradiction with the current timer state
Try to deactivate a timer which is not
started: action in contradiction with the
current timer state
Start 8 timers successfully
ENVELOPE TIMER EXPIRATION
27.22.4.21.2
Pending proactive UICC command
Card application toolkit busy
22
23
24
25
26
ETSI TS 102 384 V10.3.0 (2015-08)
Release
Test
sequence(s)
Rel-4
Terminal
Rel-5
Terminal
Rel-6
Terminal
Rel-7
Terminal
Rel-8
Terminal
Terminal
Profile
Rel-4
Rel-4
Rel-4
1.1
1.2
2.1
C109
C109
C109
C109
C109
C109
C109
C109
C109
C109
C109
C109
C109
C109
C109
E.1/50
E.1/50
E.1/50
Rel-4
Rel-4
Rel-4
Rel-4
1.1
1.2
1.3
2.1
C109
C109
C109
C116
C109
C109
C109
C116
C109
C109
C109
C116
C109
C109
C109
C116
C109
C109
C109
C116
E.1/49
E.1/49
E.1/49
E.1/49
Rel-4
Rel-4
1.1
1.2
C109
C109
C109
C109
C109
C109
C109
C109
C109
C109
E.1/52
E.1/52
Rel-4
Rel-4
1.3
2.1
C109
C116
C109
C116
C109
C116
C109
C116
C109
C116
E.1/52
E.1/52
Rel-4
1.1
M
M
M
M
M
E.1/57 AND E.1/58
Rel-4
1.2
M
M
M
M
M
E.1/57 AND E.1/58
Rel-4
1.3
M
M
M
M
M
E.1/57 AND E.1/58
Rel-4
1.4
M
M
M
M
M
E.1/57 AND E.1/58
Rel-4
1.5
M
M
M
M
M
E.1/57 AND E.1/58
Rel-4
1.6
M
M
M
M
M
E.1/57 AND E.1/58
Rel-4
Rel-4
2.1
2.2
M
M
M
M
M
M
M
M
M
M
E.1/6 AND E.1/57
E.1/6 AND E.1/57
AND E.1/20
SET UP IDLE MODE TEXT 27.22.4.22
Display idle mode text
Rel-4
1.1
M
M
M
M
C170 AND
C171
Replace idle mode text
Rel-4
1.2
M
M
M
M
C170 AND
C171
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
ETSI
Support
Release 10
Item
28
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Remove idle mode test
Rel-4
Test
sequence(s)
1.3
Rel-4
Terminal
M
Rel-5
Terminal
M
Rel-6
Terminal
M
Rel-7
Terminal
M
Rel-8
Terminal
C170 AND
C171
Competing information on Terminal
display
Rel-4
1.4
M
M
M
M
C170 AND
C171
Terminal powered cycled
Rel-4
1.5
M
M
M
M
C170 AND
C171
Refresh with NAA initialization
Rel-4
1.6
M
M
M
M
C170 AND
C171
Large text string
Rel-4
1.7
M
M
M
M
C170 AND
C171
Icons
Rel-4
2.1, 2.2, 2.3
C108
C108
C108
C108
Icons
Rel-4
2.4
C108
C108
C108
C108
UCS2 display in Cyrillic
Rel-4
3.1
C118
C118
C118
C118
Text attribute - left alignment
Rel-5
4.1
C146
C146
C146
C108 AND
C170 AND
C171
C108 AND
C170
C118 AND
C170 AND
C171
C146 AND
C170 AND
C171
Text attribute - center alignment
Rel-5
4.2
C147
C147
C147
C147 AND
C170 AND
C171
Text attribute - right alignment
Rel-5
4.3
C148
C148
C148
C148 AND
C170 AND
C171
Text attribute - large font size
Rel-5
4.4
C150
C150
C150
C150 AND
AND C149 AND C149 AND C149 C149 AND
C170 AND
C171
ETSI
Terminal
Profile
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.124
AND E.1/33 AND
E.1/39 AND E1/110
AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/39
AND E1/110 AND
E1/111
E.1/61 AND E.1/39
AND E1/110
E.1/61 AND E.1/15
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/217
AND E1/110 AND
E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/218
AND E1/110 AND
E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/219
AND E1/110 AND
E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/221
AND E.1/220 AND
E1/110 AND E1/111
Support
Release 10
Item
27
29
Description
Release
Rel-4
Terminal
ETSI TS 102 384 V10.3.0 (2015-08)
Text attribute - small font size
Rel-5
Test
sequence(s)
4.5
Rel-5
Rel-6
Rel-7
Rel-8
Terminal
Terminal
Terminal
Terminal
C151
C151
C151
C151 AND
AND C149 AND C149 AND C149 C149 AND
C170 AND
C171
Text attribute - bold on
Rel-5
4.6
C153
C153
C153
C153 AND
AND C152 AND C152 AND C152 C152 AND
C170 AND
C171
Text attribute - italic on
Rel-5
4.7
C154
C154
C154
C154 AND
AND C152 AND C152 AND C152 C152 AND
C170 AND
C171
Text attribute -underlined on
Rel-5
4.8
C155
C155
C155
C155 AND
AND C152 AND C152 AND C152 C152 AND
C170 AND
C171
Text attribute -strikethrough on
Rel-5
4.9
C156
C156
C156
C156 AND
AND C152 AND C152 AND C152 C152 AND
C170 AND
C171
Text attribute - foreground and
background colours
Rel-5
4.10
C157
C157
C157
C157 AND
AND C158 AND C158 AND C158 C158 AND
C170 AND
C171
UCS2 display in Chinese
Rel-4
5.1
C143
C143
C143
UCS2 display in Katakana
Rel-4
6.1
C145
C145
C145
Frames
Rel-6
TBD
C133
C133
RUN AT COMMAND
27.22.4.23
No alpha Identifier
null data alpha identifier presented
alpha identifier presented
Rel-4
Rel-4
Rel-4
1.1
1.2
1.3
C110
C110
C110
C110
C110
C110
C110
C110
C110
C110
C110
C110
ETSI
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170 AND
C171
C110
C110
C110 AND
C170
Terminal
Profile
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/222
AND E.1/220 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/226
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/227
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/228
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/229
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/230
AND E.1/231 AND
E1/110 AND E1/111
E.1/61 AND E.1/15
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/15
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/177
AND E.1/178 AND
E1/110 AND E1/111
E.1/62
E.1/62
E.1/62 AND E1/110
Support
Release 10
Item
30
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Icons
Rel-4
Text attribute - left alignment
Rel-5
Test
sequence(s)
2.1, 2.2, 2.3,
2.4, 2.5
3.1
Rel-4
Terminal
C114
Rel-5
Terminal
C114
Rel-6
Terminal
C114
Rel-7
Terminal
C114
Text attribute - center alignment
Rel-5
3.2
C110 AND C110 AND C110 AND
C147
C147
C147
Text attribute - right alignment
Rel-5
3.3
C110 AND C110 AND C110 AND
C148
C148
C148
Text attribute - large font size
Rel-5
3.4
C110 AND C110 AND C110 AND
C150 AND C150 AND C150 AND
C149
C149
C149
Text attribute - small font size
Rel-5
3.5
C110 AND C110 AND C110 AND
C151 AND C151 AND C151 AND
C149
C149
C149
Text attribute - bold on
Rel-5
3.6
C110 AND C110 AND C110 AND
C153 AND C153 AND C153 AND
C152
C152
C152
Text attribute - italic on
Rel-5
3.7
C110 AND C110 AND C110 AND
C154 AND C154 AND C154 AND
C152
C152
C152
Text attribute -underlined on
Rel-5
3.8
C110 AND C110 AND C110 AND
C155 AND C155 AND C155 AND
C152
C152
C152
Text attribute -strikethrough on
Rel-5
3.9
C110 AND C110 AND C110 AND
C156 AND C156 AND C156 AND
C152
C152
C152
Text attribute - foreground and
background colours
Rel-5
3.10
C110 AND C110 AND C110 AND
C157 AND C157 AND C157 AND
C158
C158
C158
UCS2 display in Cyrillic
Rel-4
4.1
UCS2 display in Chinese
Rel-4
UCS2 display in Katakana
Rel-4
C110 AND C110 AND C110 AND
C146
C146
C146
C159
C1598
C159
C159
5.1
C160
C160
C160
6.1
C161
C161
C161
ETSI
Rel-8
Terminal
C114 AND
C170
C110 AND
C146 AND
C170
C110 AND
C147 AND
C170
C110 AND
C148 AND
C170
C110 AND
C150 AND
C149 AND
C170
C110 AND
C151 AND
C149 AND
C170
C110 AND
C153 AND
C152 AND
C170
C110 AND
C154 AND
C152 AND
C170
C110 AND
C155 AND
C152 AND
C170
C110 AND
C156 AND
C152 AND
C170
C110 AND
C157 AND
C158 AND
C170
C159 AND
C170
C160 AND
C170
C161 AND
C170
Terminal
Profile
E.1/62 AND E1/110
E.1/62 AND E.1/124
AND E.1/217 AND
E1/110
E.1/62 AND E.1/124
AND E.1/218 AND
E1/110
E.1/62 AND E.1/124
AND E.1/219 AND
E1/110
E.1/124 AND E.1/221
AND E.1/220 AND
E1/110
E.1/62 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
E.1/62 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
E.1/62 AND E.1/15
AND E1/110
E.1/62 AND E.1/15
AND E1/110
E.1/62 AND E.1/15
AND E1/110
Support
Release 10
Item
28
29
30
31
32
31
Description
Release
Frames
Rel-6
Test
sequence(s)
TBD
SEND DTMF
27.22.4.24
LANGUAGE NOTIFICATION
27.22.4.25
Specific language notification
Non specific language notification
LAUNCH BROWSER
27.22.4.26
OPEN CHANNEL
27.22.4.27
Void
Rel-4
N/A
Rel-4
Rel-4
Rel-4
1.1
1.2
N/A
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-4
Terminal
Rel-5
Terminal
Rel-6
Terminal
C135
Rel-7
Terminal
C135
Rel-8
Terminal
C135 AND
C170
Terminal
Profile
E.1/62 AND E.1/177
AND E.1/178 AND
E1/110
E.1/66
M
M
M
M
M
M
M
M
C174
C174
E.1/70
E.1/70
E.1/71
Void
Open Channel (related to GPRS)
Rel-4
N/A
E.1/89 AND E.1/98
Open Channel (default bearer)
Rel-4
N/A
E.1/89 AND E.1/98
Open Channel (Local Bearer)
Rel-4
TBD
E.1/89 AND E.1/98
Open Channel (GPRS, support of Text
Attribute)
Open Channel (related to UICC Server
Mode)
Open Channel, TCP in LISTEN state,
command performed with modification
Open Channel (related to Terminal
Server Mode), TCP
Open Channel (related to Terminal
Server Mode), UDP
Open Channel (related to Terminal
Server Mode), TCP, confirmation
parameters
Open Channel (related to Terminal
Server Mode), UDP, confirmation
parameters
Open Channel (related to Terminal
Server Mode), Direct communication
channel
Open Channel (related to Terminal
Server Mode), Direct communication
channel, confirmation parameters
CLOSE CHANNEL
27.22.4.28
Close Channel (related to GPRS)
Rel-5
N/A
E.1/89 AND E.1/98
Rel-7
6.1
C162
C162
E.1/89 AND E.1/131
Rel-7
6.2
C163
C163
E.1/89 AND E.1/131
Rel-7
7.1
C164
C164
E.1/89 AND E.1/132
Rel-7
7.2
C165
C165
E.1/89 AND E.1/133
Rel-10
7.3
E.1/89 AND E.1/132
AND E.1/243
Rel-10
7.4
E.1/89 AND E.1/133
AND E.1/243
Rel-10
7.5
E.1/89 AND E.1/134
Rel-10
7.6
E.1/89 AND E.1/134
AND E.1/243
Rel-4
N/A
E.1/89 AND E.1/90
ETSI
Support
Release 10
Item
33
34
35
36
37
38
39
40
32
Description
Release
Close Channel (support of Text Attribute)
Rel-5
Test
sequence(s)
N/A
Close Channel (related to UICC Server
Mode)
Close Channel (related to Terminal
Server Mode)
RECEIVE DATA
27.22.4.29
SEND DATA
27.22.4.30
GET CHANNEL STATUS 27.22.4.31
GET CHANNEL STATUS (related to
GPRS)
GET CHANNEL STATUS (related to
UICC Server Mode)
Void
Void
Void
CALL CONTROL BY NAA
27.22.6
Rel-7
Rel-7
Terminal
Rel-8
Terminal
Terminal
Profile
E.1/89 AND E.1/90
3.1 to 3.2
C162
C162
Rel-7
4.1
C164
C164
Rel-4
Rel-4
N/A
N/A
E.1/89 AND E.1/90
AND E.1/131
E.1/89 AND E.1/90
AND E.1/132
E.1/89 AND E.1/91
E.1/89 AND E.1/92
Rel-4
N/A
E.1/93
Rel-7
2.1 to 2.2
Rel-4
N/A
E.1/7 AND E.1/8 AND
E.1/10 AND
E.1/11 AND E.1/13
AND E.1/29 AND
E.1/64
Rel-4
Rel-4
Rel-4
N/A
N/A
N/A
Rel-4
Rel-4
Rel-4
N/A
N/A
1.1
M
M
M
M
C171
27.22.7.6: idle screen available event
Rel-4
1.1
M
M
M
M
C170 And
C171
27.22.7.7.1: Card reader status normal
27.22.7.7.2: Detachable card reader
27.22.7.8: language selection event
Rel-4
Rel-4
Rel-4
1.1
2.1
1.1
C109
C116
M
C109
C116
M
C109
C116
M
C109
C116
M
C109
C116
C170 AND
C171 AND
C174
27.22.7.9: Browser termination event
27.22.7.10: Data available event (related
to GPRS)
Rel-4
Rel-4
N/A
N/A
E.1/34 AND E.1/33
E.1/35 AND E.1/33
E.1/35 AND
E.1/29 AND E.1/33
E.1/36 AND E.1/33
E.1/37 AND E.1/33
E.1/38 AND E.1/33
AND E1/111
E.1/39 AND E.1/33
AND E1/110 AND
E1/111
E.1/40 AND E.1/33
E.1/40 AND E.1/33
E.1/41 AND E.1/33
AND E1/110 AND
E1/111
E.1/42 AND E.1/33
E.1/43
AND E.1/89 AND
E.1/33
EVENT DOWNLOAD
27.22.7
27.22.7.1: MT call event
27.22.7.2.1: call connected event
27.22.7.2.2: Terminal supporting SET UP
CALL
27.22.7.3: call disconnected event
27.22.7.4: location status event
27.22.7.5: user activity event
Rel-4
Terminal
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-5
Terminal
Rel-6
Terminal
C162
ETSI
C162
E.1/89, E.1/93 AND
E.1/131
Support
Release 10
Item
41
42
43
44
45
46
47
48
49
50
51
52
53
33
Description
Release
Rel-4
Terminal
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.7.10.2: Data available event
(related to UICC server mode)
Rel-7
Test
sequence(s)
2.1
Rel-5
Terminal
Rel-6
Terminal
Rel-7
Terminal
C162
Rel-8
Terminal
C162
27.22.7.11: Channel status event
(related to GPRS)
27.22.7.11.2: Channel status event
(related to UICC server mode)
Rel-4
N/A
Rel-7
2.1 to 2.2
27.22.7.12: Access Technology change
event
27.22.7.13: Display parameter changed
event
27.22.7.14: Local connection event
27.22.7.15: Network search mode
change event
27.22.7.16: Browsing status event
27.22.7.17: Frame Information changed
event
27.22.7.18: HCI connectivity event
27.22.7.19: Contactless state request
Void
SERVICE SEARCH
GET SERVICE INFORMATION
DECLARE SERVICE
Void
Void
Void
SET FRAMES
GET FRAME STATUS
Handling of command number
DISPLAY TEXT normal priority
Rel-4
N/A
Terminal
Profile
E.1/43 AND E.1/89
AND E.1/33 AND
E.1/131
E.1/44 AND E.1/89
AND E.1/33
E.1/44 AND E.1/89
AND E.1/33 AND
E.1/131
E.1/45 AND E.1/33
C162
C162
Rel-4
N/A
E.1/46 AND E.1/33
Rel-4
Rel-6
N/A
N/A
E.1/47 AND E.1/33
E.1/48 AND E.1/33
Rel-6
Rel-6
N/A
TBD
E.1/193 AND E.1/33
REL-7
REL-9
1.1
1.1
Rel-4
Rel-4
Rel-4
N/A
N/A
N/A
Rel-6
Rel-6
TBD
TBD
Rel-4
1.1
Terminal Applications (one application)
Rel-7
1.1 to 1.2
Terminal Applications (one application),
Extended Terminal Applications
Terminal Applications (several
applications)
ACTIVATE
27.22.4.32
Rel-10
1.3
Rel-7
2.1
C166
C166
E.1/235
Rel-7
1.1
C167
C167
E.1/237
CONTACTLESS STATE CHANGED
27.22.4.33
Rel-9
1.1
C168
C168
E.1/198 AND E.1/33
E.1/201 AND E.1/33
E.1/94
E.1/95
E.1/96
M
M
C133
C133
C133
C133
C133
C133
E.1/177
E.1/178
M
M
C170 AND
C171
E.1/17 AND E1/110
AND E1/111
C166
C166
E.1/235
TERMINAL APPLICATIONS 27.22.10
E.1/235
E1/241
ETSI
Support
Release 10
34
ETSI TS 102 384 V10.3.0 (2015-08)
Table B.1b: Applicability of tests (from release 9)
Item
1
2
3
4
Description
PROFILE DOWNLOAD
27.22.1
Contents of the TERMINAL PROFILE
command
27.22.2
Servicing of Proactive UICC
Commands
27.22.3
DISPLAY TEXT
27.22.4.1
Unpacked
Screen busy
high priority
Packed
Clear after delay
Long text up to 160 bytes
Backwards move in Proactive UICC
session
Session terminated by user
Release
Rel-4
Rel-4
Test
sequence(s)
1
Rel-4
Rel-9
Terminal
M
M
Rel-10
Terminal
M
M
M
M
C170
C170
C170
C170
C170
C170
C170 AND
C171
C170 AND
C171
C170
C120 AND
C170 AND
C171
C170
Rel-4
Rel-4
Rel-4
Rel-4
Rel-4
Rel-4
Rel-4
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Rel-4
1.8
Command not understood by Terminal
No response from user
Rel-4
Rel-4
1.9
2.1
Extension Text
Rel-4
3.1
C170
C170
C170
C170
C170
C170
C170 AND
C171
C170 AND
C171
C170
C120 AND
C170 AND
C171
C170
Sustained text
Rel-4
4.1, 4.2
C170
C170
Sustained text
Rel-4
4.3
C170 AND
C171
C170 AND
C171
Icons
Rel-4
5.1, 5.2, 5.3
UCS2 display in Cyrillic
Rel-4
6.1
Variable Timeout
Rel-4
7.1
Text attribute - left alignment
Rel-5
8.1
C108 AND
C170 AND
C171
C118 AND
C170 AND
C171
C126 AND
C170 AND
C171
C146 AND
C170 AND
C171
C108 AND
C170 AND
C171
C118 AND
C170 AND
C171
C126 AND
C170 AND
C171
C146 AND
C170 AND
C171
ETSI
Terminal
Profile
E.1/1
E.1/1
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/110
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/16
AND E.1/110
E.1/17 AND E.1/65
AND E.1/110
E.1/17 AND E.1/65
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/110
AND E.1/111
E.1/17 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/137
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/124
AND E.1/217 AND
E.1/110 AND E.1/111
Support
Release 10
35
Item
Description
Release
Text attribute - center alignment
Rel-5
Test
sequence(s)
8.2
Text attribute - right alignment
Rel-5
8.3
Text attribute - large font size
Rel-5
8.4
Text attribute - small font size
Rel-5
8.5
Text attribute - bold on
Rel-5
8.6
Text attribute - italic on
Rel-5
8.7
Text attribute - underlined on
Rel-5
8.8
Text attribute -strikethrough on
Rel-5
8.9
Text attribute - foreground and
background colours
Rel-5
8.10
UCS2 display_in Chinese
Rel-4
9.1
UCS2 display_in Katakana
Rel-4
10.1
Frames
Rel-6
TBD
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170
Rel-10
Terminal
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170
Terminal
Profile
E.1/17 AND E.1/124
AND E.1/218 AND
E.1/110 AND E.1/111
E.1/17 AND E.1/124
AND E.1/219 AND
E.1/110 AND E.1/111
E.1/17 AND E.1/124
AND E.1/221 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/222 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/226 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/227 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/225 AND
E.1/228 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/229 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/17 AND E.1/124
AND E.1/230 AND
E.1/231 AND E.1/110
AND E.1/111
E.1/17 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/17 AND E.1/177
AND E.1/178 AND
E.1/110
Support
Release 10
36
Item
5
Description
ETSI TS 102 384 V10.3.0 (2015-08)
Release
Test
sequence(s)
Rel-9
Terminal
Rel-10
Terminal
Terminal
Profile
Rel-4
1.1
Prompt packed
Rel-4
1.2
Backwards move in UICC session
Rel-4
1.3
Session terminated by user
Rel-4
1.4
SMS alphabet
Rel-4
1.5
Long text up to 160 bytes
Rel-4
1.6
No response from user
Rel-4
2.1
Rel-4
3.1
UCS2 display in Cyrillic, Long text up to
70 chars
Rel-4
3.2
UCS2 format of entry in Russian
Rel-4
4.1
"Yes/No" response
Rel-4
5.1
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C120 AND
C170 AND
C171
C118 AND
C170 AND
C171
C118 AND
C170 AND
C171
C105 AND
C170 AND
C171
C170 AND
C171
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
UCS2 display in Cyrillic
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C120 AND
C170 AND
C171
C118 AND
C170 AND
C171
C118 AND
C170 AND
C171
C105 AND
C170 AND
C171
C170 AND
C171
Icons
Rel-4
6.1, 6.2, 6.3,
6.4
Help information
Rel-4
7.1
Variable Timeout
Rel-4
8.1
Text attribute - left alignment
Rel-5
9.1
Text attribute - center alignment
Rel-5
9.2
C108 AND
C170 AND
C171
C107 AND
C170 AND
C171
C126 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
C108 AND
C170 AND
C171
C107 AND
C170 AND
C171
C126 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
GET INKEY
Prompt unpacked
27.22.4.2
ETSI
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/60
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/110
AND E.1/111
E.1/18 AND E.1/140
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/124
AND E.1/217 AND
E.1/110 AND E.1/111
E.1/18 AND E.1/124
AND E.1/218 AND
E.1/110 AND E.1/111
Support
Release 10
37
Item
Description
Release
Text attribute - right alignment
Rel-5
Test
sequence(s)
9.3
Text attribute - large font size
Rel-5
9.4
Text attribute - small font size
Rel-5
9.5
Text attribute - bold on
Rel-5
9.6
Text attribute - italic on
Rel-5
9.7
Text attribute -underlined on
Rel-5
9.8
Text attribute -strikethrough on
Rel-5
9.9
Text attribute - foreground and
background colours
Rel-5
9.10
UCS2 display in Chinese
Rel-4
10.1, 10.2
UCS2 format of entry in Chinese
Rel-4
11.1
UCS2 display in Katakana
Rel-4
12.1
UCS2 format of entry in Katagana
Rel-4
13.1
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C142 AND
C170 AND
C171
C145 AND
C170 AND
C171
C144 AND
C170 AND
C171
Rel-10
Terminal
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C142 AND
C170 AND
C171
C145 AND
C170 AND
C171
C144 AND
C170 AND
C171
Terminal
Profile
E.1/18 AND E.1/124
AND E.1/219 AND
E.1/110 AND E.1/111
E.1/18 AND E.1/124
AND E.1/221 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/222 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/226 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/227 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/18 AND E.1/124
AND E.1/228 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/18 AND
E.1/124AND E.1/229
AND E.1/225 AND
E.1/110 AND E.1/111
E.1/18 AND E.1/124
AND E.1/230 AND
E.1/231 AND E.1/110
AND E.1/111
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/18 AND E.1/14
AND E.1/110 AND
E.1/111
Support
Release 10
38
Item
Description
Release
Rel-6
Test
sequence(s)
TBD
Rel-9
Terminal
C133 AND
C170 AND
C171
Rel-10
Terminal
C133 AND
C170 AND
C171
Terminal
Profile
E.1/19 AND E.1/177
AND E.1/178 AND
E.1/110 AND E.1/111
Rel-4
1.1
Input packed
Rel-4
1.2
SMS alphabet
Rel-4
1.3
Hidden input
Rel-4
1.4
Min / max acceptable length
Rel-4
1.5
Backwards move in UICC session
Rel-4
1.6
Session terminated by user
Rel-4
1.7
Prompt text up to 160 bytes
Rel-4
1.8
SMS default alphabet, Terminal to echo
text, packing not required
Null length for the text string
Rel-4
1.9
Rel-4
1.10
No response from user
Rel-4
2.1
Rel-4
3.1, 3.2
UCS2 entry in Cyrillic
Rel-4
4.1, 4.2
Default text for the input
Rel-4
5.1, 5.2
Icons
Rel-4
6.1, 6.2, 6.3,
6.4
Help information
Rel-4
7.1
Text attribute - left alignment
Rel-5
8.1
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C120 AND
C170 AND
C171
C118 AND
C170 AND
C171
C105 AND
C170 AND
C171
C170 AND
C171
C108 AND
C170 AND
C171
C107 AND
C170 AND
C171
C146 AND
C170 AND
C171
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
UCS2 display in Cyrillic
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C120 AND
C170 AND
C171
C118 AND
C170 AND
C171
C105 AND
C170 AND
C171
C170 AND
C171
C108 AND
C170 AND
C171
C107 AND
C170 AND
C171
C146 AND
C170 AND
C171
Frames
6
ETSI TS 102 384 V10.3.0 (2015-08)
GET INPUT
Input unpacked
27.22.4.3
ETSI
E.1/19 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/217 AND
E.1/110 AND E.1/111
Support
Release 10
39
Item
Description
Release
Text attribute - center alignment
Rel-5
Test
sequence(s)
8.2
Text attribute - right alignment
Rel-5
8.3
Text attribute - large font size
Rel-5
8.4
Text attribute - small font size
Rel-5
8.5
Text attribute - bold on
Rel-5
8.6
Text attribute - italic on
Rel-5
8.7
Text attribute -underlined on
Rel-5
8.8
Text attribute -strikethrough on
Rel-5
8.9
Text attribute - foreground and
background colours
Rel-5
8.10
UCS2 display in Chinese
Rel-4
9.1, 9.2
UCS2 entry in Chinese
Rel-4
10.1, 10.2
UCS2 display in Katakana
Rel-4
11.1, 11.2
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C142 AND
C170 AND
C171
C145 AND
C170 AND
C171
Rel-10
Terminal
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C143 AND
C170 AND
C171
C142 AND
C170 AND
C171
C145 AND
C170 AND
C171
Terminal
Profile
E.1/19 AND E.1/124
AND E.1/218 AND
E.1/110 AND E.1/111
E.1/19 AND E.1/124
AND E.1/219 AND
E.1/110 AND E.1/111
E.1/19 AND E.1/124
AND E.1/221 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/222 AND
E.1/220 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/226 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/227 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/228 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/229 AND
E.1/225 AND E.1/110
AND E.1/111
E.1/19 AND E.1/124
AND E.1/230 AND
E.1/231 AND E.1/110
AND E.1/111
E.1/19 AND E.1/15
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/15
AND E.1/110 AND
E.1/111
Support
Release 10
40
Item
7
8
Description
UCS2 entry in Katakana
Rel-4
Test
sequence(s)
12.1, 12.2
Frames
Rel-6
TBD
Rel-4
1.1
Rel-4
1.1
UCS2 display in Cyrillic
Rel-4
2.1
Icons
Rel-4
3.1, 3.2,3.3,
3.4
Text attribute - left alignment
Rel-5
4.1
Text attribute - center alignment
Rel-5
4.2
Text attribute - right alignment
Rel-5
4.3
Text attribute - large font size
Rel-5
4.4
Text attribute - small font size
Rel-5
4.5
Text attribute - bold on
Rel-5
4.6
Text attribute - italic on
Rel-5
4.7
MORE TIME
PLAY TONE
Play all tones
Release
27.22.4.4
27.22.4.5
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C144 AND
C170 AND
C171
C133 AND
C170 AND
C171
M
Rel-10
Terminal
C144 AND
C170 AND
C171
C133 AND
C170 AND
C171
M
Terminal
Profile
E.1/19 AND E.1/14
AND E.1/110 AND
E.1/111
E.1/19 AND E.1/177
AND E.1/178 AND
E.1/110 AND E.1/111
E.1/20
C170 AND
C171 AND
C172
C118 AND
C170 AND
C172
C108 AND
C170 AND
C172
C146 AND
C170 AND
C172
C147 AND
C170 AND
C172
C148 AND
C170 AND
C172
C150 AND
C149 AND
C170 AND
C172
C151 AND
C149 AND
C170 AND
C172
C153 AND
C152 AND
C170 AND
C172
C154 AND
C152 AND
C170 AND
C172
C170 AND
C171 AND
C172
C118 AND
C170 AND
C172
C108 AND
C170 AND
C172
C146 AND
C170 AND
C172
C147 AND
C170 AND
C172
C148 AND
C170 AND
C172
C150 AND
C149 AND
C170 AND
C172
C151 AND
C149 AND
C170 AND
C172
C153 AND
C152 AND
C170 AND
C172
C154 AND
C152 AND
C170 AND
C172
E.1/21 AND E1/110
AND E.1/111
E.1/21
AND E.1/15 AND
E1/110
E.1/21 AND E1/110
E.1/21 AND E.1/124
AND E.1/217 AND
E1/110
E.1/21 AND E.1/124
AND E.1/218 AND
E1/110
E.1/21 AND E.1/124
AND E.1/219 AND
E1/110
E.1/21 AND E.1/124
AND E.1/221 AND
E.1/220 AND E1/110
E.1/21 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
E.1/21 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
E.1/21 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
Support
Release 10
41
Item
9
10
11
Description
Text attribute -underlined on
Rel-5
Test
sequence(s)
4.8
Text attribute -strikethrough on
Rel-5
4.9
Text attribute - foreground and
background colours
Rel-5
4.10
UCS2 display in Chinese
Rel-4
5.1
UCS2 display in Katakana
Rel-4
6.1
Frames
Rel-6
TBD
Themed and Melody tones
Rel-6
TBD
Rel-4
1.1
Rel-4
N/A
Rel-4
Rel-4
1.2
N/A
Rel-4
Rel-4
Rel-4
Rel-4
N/A
1.5
N/A
N/A
Rel-4
1.1
Rel-4
1.2
Rel-4
2.1
POLL INTERVAL
27.22.4.6
Duration
REFRESH
27.22.4.7
NAA Initialization and Full File Change
Notification
File Change Notification
NAA Initialization and File Change
Notification
NAA Initialization
UICC Reset
NAA Application Reset
NAA Session Reset
SET UP MENU
27.22.4.8
Set up, menu selection, replace and
remove menu
Large menu
Help information
Release
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C155 AND
C152 AND
C170 AND
C172
C156 AND
C152 AND
C170 AND
C172
C157 AND
C158 AND
C170 AND
C172
C143 AND
C170 AND
C172
C145 AND
C170 AND
C172
C133 AND
C170 AND
C172
C138 AND
C170 AND
C172
Rel-10
Terminal
C155 AND
C152 AND
C170 AND
C172
C156 AND
C152 AND
C170 AND
C172
C157 AND
C158 AND
C170 AND
C172
C143 AND
C170 AND
C172
C145 AND
C170 AND
C172
C133 AND
C170 AND
C172
C138 AND
C170 AND
C172
Terminal
Profile
E.1/21 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
M
M
E.1/22
E.1/21 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
E.1/21 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
E.1/21
AND E.1/15 AND
E1/110
E.1/21
AND E.1/15 AND
E1/110
E.1/21 AND E.1/177
AND E.1/178 AND
E1/110
E.1/21 AND E1/110
E.1/24
M
M
M
M
C170 AND
C171
C170 AND
C171
C107 AND
C170 AND
C171
C170 AND
C171
C170 AND
C171
C107 AND
C170 AND
C171
E.1/24
E.1/24
E.1/24
E.1/24
E.1/24
E.1/24
E.1/30 AND E.1/4 AND
E1/110 AND E1/111
E.1/30 AND E.1/4 AND
E1/110 AND E1/111
E.1/30 AND E.1/4 AND
E1/110 AND E1/111
Support
Release 10
42
Item
Description
Release
Next action indicator
Rel-4
Test
sequence(s)
3.1
Icons
Rel-4
4.1, 4.2
Soft key access
Rel-4
5.1
Text attribute
Rel-5
6.1
Text attribute - center alignment
Rel-5
6.2
Text attribute - right alignment
Rel-5
6.3
Text attribute - large font size
Rel-5
6.4
Text attribute - small font size
Rel-5
6.5
Text attribute - bold on
Rel-5
6.6
Text attribute - italic on
Rel-5
6.7
Text attribute -underlined on
Rel-5
6.8
Text attribute -strikethrough on
Rel-5
6.9
Text attribute - foreground and
background colours
Rel-5
6.10
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C170 AND
C171
C108 AND
C170 AND
C171
C112 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
Rel-10
Terminal
C170 AND
C171
C108 AND
C170 AND
C171
C112 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
Terminal
Profile
E.1/30 AND E1/110
AND E1/111
E.1/30 AND E1/110
AND E1/111
E.1/30 AND E.1/74
AND E1/110 AND
E1/111
E.1/30 AND E.1/124
AND E.1/217 AND
E1/110 AND E1/111
E.1/30 AND E.1/124
AND E.1/218 AND
E1/110 AND E1/111
E.1/30 AND E.1/124
AND E.1/219 AND
E1/110 AND E1/111
E.1/30 AND E.1/124
AND E.1/221 AND
E.1/220 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
AND E1/111
E.1/30 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
AND E1/111
Support
Release 10
43
Item
12
Description
UCS2 Display in Cyrillic
Rel-4
Test
sequence(s)
7.1
UCS2 Display in Chinese
Rel-4
8.1
UCS2 Display in Katakana
Rel-4
9.1
Rel-4
1.1
Large menu
Rel-4
1.2, 1.3, 1.6
Backwards move
Rel-4
1.4
User termination
Rel-4
1.5
Next action indicator
Rel-4
2.1
Default selected item
Rel-4
3.1
Help information
Rel-4
4.1
Icons
Rel-4
5.1, 5.2
Presentation style
Rel-4
6.1, 6.2
Soft keys
Rel-4
7.1
No Response from user
Rel-4
8.1
Text attribute - left alignment
Rel-5
9.1
Text attribute - center alignment
Rel-5
9.2
SELECT ITEM
Mandatory features
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C118 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
Rel-10
Terminal
C118 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
Terminal
Profile
E.1/39
AND E.1/15 AND
E1/110 AND E1/111
E.1/39
AND E.1/15 AND
E1/110 AND E1/111
E.1/39
AND E.1/15 AND
E1/110 AND E1/111
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C107 AND
C170 AND
C171
C108 AND
C170 AND
C171
C170 AND
C171
C112 AND
C170 AND
C171
C120 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C170 AND
C171
C107 AND
C170 AND
C171
C108 AND
C170 AND
C171
C170 AND
C171
C112 AND
C170 AND
C171
C120 AND
C170 AND
C171
C146 AND
C170 AND
C171
C147 AND
C170 AND
C171
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
27.22.4.9
ETSI
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E.1/73
AND E1/110 AND
E1/111
E.1/25 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/217 AND
E1/110 AND E1/111
E.1/25 AND E.1/124
AND E.1/218 AND
E1/110 AND E1/111
Support
Release 10
44
Item
13
14
Description
Text attribute - right alignment
Rel-5
Test
sequence(s)
9.3
Text attribute - large font size
Rel-5
9.4
Text attribute - small font size
Rel-5
9.5
Text attribute - bold on
Rel-5
9.6
Text attribute - italic on
Rel-5
9.7
Text attribute -underlined on
Rel-5
9.8
Text attribute -strikethrough on
Rel-5
9.9
Text attribute - foreground and
background colours
Rel-5
9.10
UCS2 Display in Cyrillic
Rel-4
10.1,10.2,10.
3
UCS2 Display in Chinese
Rel-4
11.1
UCS2 Display in Katakana
Rel-4
12.1,12.2,12.
3
Frames
Rel-6
TBD
Rel-4
N/A
SEND SMS
Void
Release
27.22.4.10
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C118 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170 AND
C171
Rel-10
Terminal
C148 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
C151 AND
C149 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
C118 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170 AND
C171
Terminal
Profile
E.1/25 AND E.1/124
AND E.1/219 AND
E1/110 AND E1/111
E.1/25 AND E.1/124
AND E.1/221 AND
E.1/220 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
AND E1/111
E.1/25 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
AND E1/111
E.1/25
AND E.1/15 AND
E1/110 AND E1/111
E.1/25
AND E.1/15 AND
E1/110 AND E1/111
E.1/25
AND E.1/15 AND
E1/110 AND E1/111
E.1/25 AND E.1/177
AND E.1/178 AND
E1/110 AND E1/111
E.1/26
Support
Release 10
45
Item
Description
15
16
17
18
Void
27.22.4.12
SET UP CALL
27.22.4.13
POLLING OFF
27.22.4.14
PROVIDE LOCAL INFO
27.22.4.15
Location Information according to current
NAA
IMEI of the Terminal
Network Measurement results according
to current NAA
Date, time and time zone
Language setting
Void
Access Technology
ESN of the terminal
IMEISV of the terminal
Search Mode
Charge State of the Battery
Void
Broadcast Network information
SET UP EVENT LIST
27.22.4.16
User Activity event
19
20
21
ETSI TS 102 384 V10.3.0 (2015-08)
Release
Test
sequence(s)
Rel-4
Rel-4
N/A
1.1
E.1/29
E.1/23
Rel-4
N/A
E.1/31
Rel-4
Rel-4
1.2
N/A
M
M
E.1/31
E.1/32 AND E.1/67
Rel-4
Rel-4
1.4
1.5
M
M
M
M
E.1/59
E.1/68
Rel-4
Rel-4
Rel-6
Rel-6
Rel-6
N/A
1.8
1.9
N/A
1.11
M
M
M
M
C139
C139
E.1/72
E.1/141
E.1/143
E.1/144
E.1/170
Rel-8
1.13
C169
C169
E.1/239
Rel-4
1.1
C171
C171
Replace by new event list
Rel-4
1.2
Remove event
Rel-4
1.3
Remove Event on Terminal Power Cycle
Rel-4
1.4
C170 AND
C171 AND
C174
C170 AND
C171 AND
C174
C170 AND
C171 AND
C174
C170 AND
C171 AND
C174
C170 AND
C171 AND
C174
C170 AND
C171 AND
C174
E.1/33 AND E.1/35
AND E1/111
E.1/33 AND E.1/35
AND E.1/36 AND
E1/110 AND E1/111
E.1/33 AND E.1/35
AND E1/110 AND
E1/111
E.1/33 AND E.1/35
AND E1/110 AND
E1/111
Rel-4
1.1
C109
C109
E.1/51
Rel-4
1.2
C109
C109
E.1/51
Rel-4
Rel-4
Rel-4
Rel-4
1.3
1.4
1.5
2.1
C109
C109
C109
C116
C109
C109
C109
C116
E.1/51
E.1/51
E.1/51
E.1/51
Rel-4
Rel-4
1.1
1.2
C109
C109
C109
C109
E.1/50
E.1/50
PERFORM CARD APDU 27.22.4.17
Additional card inserted, Select MF and
Get Response
Additional card inserted, Select DF GSM,
Select EF PLMN , Update Binary, Read
Binary on EF PLMN
Additional card inserted, card powered off
No card inserted, card powered off
Invalid card reader identifier
Detachable reader
POWER OFF CARD
27.22.4.18
Additional card inserted
No card inserted
ETSI
Rel-9
Terminal
Rel-10
Terminal
Terminal
Profile
Support
Release 10
46
Item
22
23
24
25
26
Description
Release
Detachable reader
POWER ON CARD
27.22.4.19
Additional card inserted
No ATR
No card inserted
Detachable reader
GET READER STATUS
27.22.4.20
Additional card inserted, card powered
Additional card inserted, card not powered
Additional card inserted, card not present
Detachable reader
TIMER MANAGEMENT 27.22.4.21.1
Start timer 1 several times, get the current
value of the timer and deactivate the timer
successfully
Start timer 2 several times, get the current
value of the timer and deactivate the timer
successfully
Start timer 8 several times, get the current
value of the timer and deactivate the timer
successfully
Try to get the current value of a timer
which is not started: action in
contradiction with the current timer state
Try to deactivate a timer which is not
started: action in contradiction with the
current timer state
Start 8 timers successfully
ENVELOPE TIMER EXPIRATION
27.22.4.21.2
Pending proactive UICC command
Card application toolkit busy
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-4
Test
sequence(s)
2.1
Rel-9
Terminal
C109
Rel-10
Terminal
C109
Terminal
Profile
E.1/50
Rel-4
Rel-4
Rel-4
Rel-4
1.1
1.2
1.3
2.1
C109
C109
C109
C116
C109
C109
C109
C116
E.1/49
E.1/49
E.1/49
E.1/49
Rel-4
Rel-4
Rel-4
Rel-4
1.1
1.2
1.3
2.1
C109
C109
C109
C116
C109
C109
C109
C116
E.1/52
E.1/52
E.1/52
E.1/52
Rel-4
1.1
M
M
E.1/57 AND E.1/58
Rel-4
1.2
M
M
E.1/57 AND E.1/58
Rel-4
1.3
M
M
E.1/57 AND E.1/58
Rel-4
1.4
M
M
E.1/57 AND E.1/58
Rel-4
1.5
M
M
E.1/57 AND E.1/58
Rel-4
1.6
M
M
E.1/57 AND E.1/58
Rel-4
Rel-4
2.1
2.2
M
M
M
M
E.1/6 AND E.1/57
E.1/6 AND E.1/57
AND E.1/20
SET UP IDLE MODE TEXT 27.22.4.22
Display idle mode text
Rel-4
1.1
C170 AND
C171
C170 AND
C171
Replace idle mode text
Rel-4
1.2
C170 AND
C171
C170 AND
C171
Remove idle mode test
Rel-4
1.3
C170 AND
C171
C170 AND
C171
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
ETSI
Support
Release 10
47
Item
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Competing information on Terminal
display
Rel-4
Test
sequence(s)
1.4
Terminal powered cycled
Rel-4
1.5
C170 AND
C171
C170 AND
C171
Refresh with NAA initialization
Rel-4
1.6
C170 AND
C171
C170 AND
C171
Large text string
Rel-4
1.7
C170 AND
C171
C170 AND
C171
Icons
Rel-4
2.1, 2.2, 2.3
Icons
Rel-4
2.4
UCS2 display in Cyrillic
Rel-4
3.1
Text attribute - left alignment
Rel-5
4.1
C108 AND
C170 AND
C171
C108 AND
C170
C118 AND
C170 AND
C171
C146 AND
C170 AND
C171
C108 AND
C170 AND
C171
C108 AND
C170
C118 AND
C170 AND
C171
C146 AND
C170 AND
C171
Text attribute - center alignment
Rel-5
4.2
C147 AND
C170 AND
C171
C147 AND
C170 AND
C171
Text attribute - right alignment
Rel-5
4.3
C148 AND
C170 AND
C171
C148 AND
C170 AND
C171
Text attribute - large font size
Rel-5
4.4
C150 AND
C149 AND
C170 AND
C171
C150 AND
C149 AND
C170 AND
C171
ETSI
Rel-9
Terminal
C170 AND
C171
Rel-10
Terminal
C170 AND
C171
Terminal
Support
Profile
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.124 AND
E.1/33 AND E.1/39
AND E1/110 AND
E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/39
AND E1/110 AND
E1/111
E.1/61 AND E.1/39
AND E1/110
E.1/61 AND E.1/15
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/217
AND E1/110 AND
E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/218
AND E1/110 AND
E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/219
AND E1/110 AND
E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/221
AND E.1/220 AND
E1/110 AND E1/111
Release 10
48
Item
27
Description
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Text attribute - small font size
Rel-5
Test
sequence(s)
4.5
Text attribute - bold on
Rel-5
4.6
C153 AND
C152 AND
C170 AND
C171
C153 AND
C152 AND
C170 AND
C171
Text attribute - italic on
Rel-5
4.7
C154 AND
C152 AND
C170 AND
C171
C154 AND
C152 AND
C170 AND
C171
Text attribute -underlined on
Rel-5
4.8
C155 AND
C152 AND
C170 AND
C171
C155 AND
C152 AND
C170 AND
C171
Text attribute -strikethrough on
Rel-5
4.9
C156 AND
C152 AND
C170 AND
C171
C156 AND
C152 AND
C170 AND
C171
Text attribute - foreground and
background colours
Rel-5
4.10
C157 AND
C158 AND
C170 AND
C171
C157 AND
C158 AND
C170 AND
C171
UCS2 display in Chinese
Rel-4
5.1
UCS2 display in Katakana
Rel-4
6.1
Frames
Rel-6
TBD
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170 AND
C171
C143 AND
C170 AND
C171
C145 AND
C170 AND
C171
C133 AND
C170 AND
C171
RUN AT COMMAND
27.22.4.23
No alpha Identifier
null data alpha identifier presented
alpha identifier presented
Rel-4
Rel-4
Rel-4
1.1
1.2
1.3
C110
C110
C110 AND
C170
C110
C110
C110 AND
C170
ETSI
Rel-9
Terminal
C151 AND
C149 AND
C170 AND
C171
Rel-10
Terminal
C151 AND
C149 AND
C170 AND
C171
Terminal
Profile
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/222
AND E.1/220 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/226
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/227
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/228
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/229
AND E.1/225 AND
E1/110 AND E1/111
E.1/61 AND E.1/33
AND E.1/39 AND
E.1/124 AND E.1/230
AND E.1/231 AND
E1/110 AND E1/111
E.1/61 AND E.1/15
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/15
AND E.1/39 AND
E1/110 AND E1/111
E.1/61 AND E.1/177
AND E.1/178 AND
E1/110 AND E1/111
E.1/62
E.1/62
E.1/62 AND E1/110
Support
Release 10
49
Item
Description
Release
Icons
Rel-4
Text attribute - left alignment
Rel-5
Test
sequence(s)
2.1, 2.2, 2.3,
2.4, 2.5
3.1
Text attribute - center alignment
Rel-5
3.2
Text attribute - right alignment
Rel-5
3.3
Text attribute - large font size
Rel-5
3.4
Text attribute - small font size
Rel-5
3.5
Text attribute - bold on
Rel-5
3.6
Text attribute - italic on
Rel-5
3.7
Text attribute -underlined on
Rel-5
3.8
Text attribute -strikethrough on
Rel-5
3.9
Text attribute - foreground and
background colours
Rel-5
3.10
UCS2 display in Cyrillic
Rel-4
4.1
UCS2 display in Chinese
Rel-4
5.1
UCS2 display in Katakana
Rel-4
6.1
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C114 AND
C170
C110 AND
C146 AND
C170
C110 AND
C147 AND
C170
C110 AND
C148 AND
C170
C110 AND
C150 AND
C149 AND
C170
C110 AND
C151 AND
C149 AND
C170
C110 AND
C153 AND
C152 AND
C170
C110 AND
C154 AND
C152 AND
C170
C110 AND
C155 AND
C152 AND
C170
C110 AND
C156 AND
C152 AND
C170
C110 AND
C157 AND
C158 AND
C170
C159 AND
C170
C160 AND
C170
C161 AND
C170
Rel-10
Terminal
C114 AND
C170
C110 AND
C146 AND
C170
C110 AND
C147 AND
C170
C110 AND
C148 AND
C170
C110 AND
C150 AND
C149 AND
C170
C110 AND
C151 AND
C149 AND
C170
C110 AND
C153 AND
C152 AND
C170
C110 AND
C154 AND
C152 AND
C170
C110 AND
C155 AND
C152 AND
C170
C110 AND
C156 AND
C152 AND
C170
C110 AND
C157 AND
C158 AND
C170
C159 AND
C170
C160 AND
C170
C161 AND
C170
Terminal
Profile
E.1/62 AND E1/110
E.1/62 AND E.1/124
AND E.1/217 AND
E1/110
E.1/62 AND E.1/124
AND E.1/218 AND
E1/110
E.1/62 AND E.1/124
AND E.1/219 AND
E1/110
E.1/124 AND E.1/221
AND E.1/220 AND
E1/110
E.1/62 AND E.1/124
AND E.1/222 AND
E.1/220 AND E1/110
E.1/62 AND E.1/124
AND E.1/226 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/227 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/228 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/229 AND
E.1/225 AND E1/110
E.1/62 AND E.1/124
AND E.1/230 AND
E.1/231 AND E1/110
E.1/62 AND E.1/15
AND E1/110
E.1/62 AND E.1/15
AND E1/110
E.1/62 AND E.1/15
AND E1/110
Support
Release 10
50
Item
28
29
30
31
32
Description
Frames
Rel-6
Test
sequence(s)
TBD
SEND DTMF
27.22.4.24
LANGUAGE NOTIFICATION 27.22.4.25
Specific language notification
Non specific language notification
LAUNCH BROWSER
27.22.4.26
OPEN CHANNEL
27.22.4.27
Void
Rel-4
N/A
Rel-4
Rel-4
Rel-4
1.1
1.2
N/A
Open Channel (related to GPRS)
Rel-4
N/A
E.1/89 AND E.1/98
Open Channel (default bearer)
Rel-4
N/A
E.1/89 AND E.1/98
Open Channel (Local Bearer)
Rel-4
TBD
E.1/89 AND E.1/98
Open Channel (GPRS, support of Text
Attribute)
Open Channel (related to UICC Server
Mode)
Open Channel, TCP in LISTEN state,
command performed with modification
Open Channel (related to Terminal Server
Mode), TCP
Open Channel (related to Terminal Server
Mode), UDP
Open Channel (related to Terminal Server
Mode), TCP, confirmation parameters
Rel-5
N/A
E.1/89 AND E.1/98
Rel-7
6.1
C162
C162
E.1/89 AND E.1/131
Rel-7
6.2
C163
C163
E.1/89 AND E.1/131
Rel-7
7.1
C164
C164
E.1/89 AND E.1/132
Rel-7
7.2
C165
C165
E.1/89 AND E.1/133
Rel-10
7.3
E.1/89 AND E.1/132
AND E.1/243
Open Channel (related to Terminal Server
Mode), UDP, confirmation parameters
Rel-10
7.4
Open Channel (related to Terminal Server
Mode), Direct communication channel
Open Channel (related to Terminal Server
Mode), Direct communication channel,
confirmation parameters
Rel-10
7.5
C176 AND
C164 AND
C170 AND
C171
C176 AND
C165 AND
C170 AND
C171
C177
Rel-10
7.6
Rel-4
N/A
CLOSE CHANNEL
27.22.4.28
Close Channel (related to GPRS)
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C135 AND
C170
Rel-10
Terminal
C135 AND
C170
Terminal
Profile
E.1/62 AND E.1/177
AND E.1/178 AND
E1/110
E.1/66
C174
C174
C174
C174
E.1/70
E.1/70
E.1/71
Void
ETSI
C177 AND
C170 AND
C171 AND
C176
E.1/89 AND E.1/133
AND E.1/243
E.1/89 AND E.1/134
E.1/89 AND E.1/134
AND E.1/243
E.1/89 AND E.1/90
Support
Release 10
51
Item
33
34
35
36
37
38
39
40
Description
Release
Close Channel (support of Text Attribute)
Close Channel (related to UICC Server
Mode)
Close Channel (related to Terminal Server
Mode)
RECEIVE DATA
27.22.4.29
SEND DATA
27.22.4.30
GET CHANNEL STATUS 27.22.4.31
GET CHANNEL STATUS (related to
GPRS)
GET CHANNEL STATUS (related to
UICC Server Mode)
Void
Void
Void
CALL CONTROL BY NAA
27.22.6
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
Rel-10
Terminal
Rel-5
Test
sequence(s)
N/A
Terminal
Profile
E.1/89 AND E.1/90
Rel-7
3.1 to 3.2
C162
C162
Rel-7
4.1
C164
C164
Rel-4
Rel-4
N/A
N/A
E.1/89 AND E.1/90
AND E.1/131
E.1/89 AND E.1/90
AND E.1/132
E.1/89 AND E.1/91
E.1/89 AND E.1/92
Rel-4
N/A
E.1/93
Rel-7
2.1 to 2.2
Rel-4
N/A
E.1/7 AND E.1/8 AND
E.1/10 AND
E.1/11 AND E.1/13
AND E.1/29 AND
E.1/64
E.1/34 AND E.1/33
E.1/35 AND E.1/33
E.1/35 AND
E.1/29 AND E.1/33
E.1/36 AND E.1/33
E.1/37 AND E.1/33
E.1/38 AND E.1/33
AND E1/111
E.1/39 AND E.1/33
AND E1/110 AND
E1/111
E.1/40 AND E.1/33
E.1/40 AND E.1/33
E.1/41 AND E.1/33
AND E1/110 AND
E1/111
E.1/42 AND E.1/33
E.1/43
AND E.1/89 AND
E.1/33
EVENT DOWNLOAD
27.22.7
27.22.7.1: MT call event
27.22.7.2.1: call connected event
27.22.7.2.2: Terminal supporting SET UP
CALL
27.22.7.3: call disconnected event
27.22.7.4: location status event
27.22.7.5: user activity event
Rel-4
Rel-4
Rel-4
N/A
N/A
N/A
Rel-4
Rel-4
Rel-4
N/A
N/A
1.1
27.22.7.6: idle screen available event
Rel-4
27.22.7.7.1: Card reader status normal
27.22.7.7.2: Detachable card reader
27.22.7.8: language selection event
27.22.7.9: Browser termination event
27.22.7.10: Data available event (related
to GPRS)
C162
C162
C171
C171
1.1
C170 And
C171
C170 And
C171
Rel-4
Rel-4
Rel-4
1.1
2.1
1.1
C109
C116
C170 AND
C171 AND
C174
C109
C116
C170 AND
C171 AND
C174
Rel-4
Rel-4
N/A
N/A
ETSI
E.1/89, E.1/93 AND
E.1/131
Support
Release 10
52
Item
41
42
43
44
45
46
47
48
49
50
Description
27.22.7.10.2: Data available event
(related to UICC server mode)
Rel-7
Test
sequence(s)
2.1
27.22.7.11: Channel status event (related
to GPRS)
27.22.7.11.2: Channel status event
(related to UICC server mode)
Rel-4
N/A
Rel-7
2.1 to 2.2
27.22.7.12: Access Technology change
event
27.22.7.13: Display parameter changed
event
27.22.7.14: Local connection event
27.22.7.15: Network search mode change
event
27.22.7.16: Browsing status event
27.22.7.17: Frame Information changed
event
27.22.7.18: HCI connectivity event
27.22.7.19: Contactless state request
Rel-4
N/A
Terminal
Profile
E.1/43 AND E.1/89
AND E.1/33 AND
E.1/131
E.1/44 AND E.1/89
AND E.1/33
E.1/44 AND E.1/89
AND E.1/33 AND
E.1/131
E.1/45 AND E.1/33
Rel-4
N/A
E.1/46 AND E.1/33
Rel-4
Rel-6
N/A
N/A
E.1/47 AND E.1/33
E.1/48 AND E.1/33
Rel-6
Rel-6
N/A
TBD
E.1/193 AND E.1/33
REL-7
REL-9
1.1
1.1
Rel-4
Rel-4
Rel-4
N/A
N/A
N/A
Rel-6
Rel-6
TBD
TBD
C133
C133
C133
C133
E.1/177
E.1/178
Rel-4
1.1
C170 AND
C171
C170 AND
C171
E.1/17 AND E1/110
AND E1/111
Terminal Applications (one application)
Rel-7
1.1 to 1.2
C166
C166
E.1/235
Terminal Applications (one application),
Extended Terminal Applications
Terminal Applications (several
applications)
ACTIVATE
27.22.4.32
Rel-10
1.3
C166
E.1/235
Rel-7
2.1
C166
C166
E.1/235
Rel-7
1.1
C167
C167
E.1/237
Void
SERVICE SEARCH
GET SERVICE INFORMATION
DECLARE SERVICE
Void
Void
Void
SET FRAMES
GET FRAME STATUS
Handling of command number
DISPLAY TEXT normal priority
51
52
Release
ETSI TS 102 384 V10.3.0 (2015-08)
Rel-9
Terminal
C162
Rel-10
Terminal
C162
C162
C162
C168
C175 AND
C171
C168
C175 AND
C171
E.1/198 AND E.1/33
E.1/201 AND E.1/33
E.1/94
E.1/95
E.1/96
TERMINAL APPLICATIONS 27.22.10
ETSI
Support
Release 10
53
Item
53
Description
CONTACTLESS STATE CHANGED
27.22.4.33
Release
Rel-9
ETSI TS 102 384 V10.3.0 (2015-08)
Test
sequence(s)
1.1
Rel-9
Terminal
C175 AND
C170
Rel-10
Terminal
C175 AND
C170
Terminal
Profile
E1/241
Table B.1c: Applicability of tests (conditions and options list)
C101
C102
C103
C104
C105
C106
C107
C108
C109
C110
C111
C112
C113
C114
C115
C116
C117
C118
C119
C120
C121
C122
C123
C124
C125
C126
C127
C128
C129
C130
C131
C132
C133
C134
C135
C136
C137
Void
Void
Void
Void
IF A.1/3 AND A.1/41 THEN M ELSE N/A
Void
IF A.1/5 THEN M ELSE N/A
IF A.1/6 THEN (O.1 OR O.2) ELSE N/A
IF A.1/7 THEN M ELSE N/A
IF (A.1/9 AND A.1/57) THEN M ELSE N/A
Void
IF A.1/11 THEN M ELSE N/A
Void
IF C110 AND C108 THEN M ELSE N/A
Void
IF A1/07 AND A.1/8 THEN M ELSE N/A
Void
IF A.1/15 AND A.1/41 THEN M ELSE N/A
Void
IF A.1/20 THEN M ELSE N/A
Void
Void
Void
Void
Void
IF A.1/24 THEN M ELSE N/A
Void
Void
Void
Void
Void
IF A.1/27 THEN M ELSE N/A
IF A.1/37 THEN M ELSE N/A
Void
IF C110 ANC C133 THEN M ELSE N/A
Void
Void
-- O_Ucs2_Entry AND O_Ucs2_Entry_Cyrillic
-- O_Help
-- O_Icons
-- O_Dual_Slot
-- O_Run_At AND O_+CGMI
-- O_Soft_key
-- O_Run_At AND O_+CGMI AND O_Icons
-- O_Dual_Slot AND O_Detach_Rdr
-- O_Ucs2_Disp AND O_Ucs2_Disp_Cyrillic
-- O_D_NoResp
-- O_Duration
-- O_BIP_Local
-- O_Frames
-- O_Run-At AND O_+CGMI AND O_Frames
ETSI
Support
Release 10
54
C138
C139
C140
C141
C142
C143
C144
C145
C146
C147
C148
C149
C150
C151
C152
C153
C154
C155
C156
C157
C158
C159
IF A.1/39 THEN M ELSE N/A
IF A.1/35 THEN M ELSE N/A
Void
Void
IF A.1/3 AND A.1/42 THEN M ELSE N/A
IF A.1/15 AND A.1/42 THEN M ELSE N/A
IF A.1/3 AND A.1/43 THEN M ELSE N/A
IF A.1/15 AND A.1/43 THEN M ELSE N/A
IF A.1/44 THEN M ELSE N/A
IF A.1/45 THEN M ELSE N/A
IF A.1/46 THEN M ELSE N/A
IF A.1/47 THEN M ELSE N/A
IF A.1/48 THEN M ELSE N/A
IF A.1/49 THEN M ELSE N/A
IF A.1/50 THEN M ELSE N/A
IF A.1/51 THEN M ELSE N/A
IF A.1/52 THEN M ELSE N/A
IF A.1/53 THEN M ELSE N/A
IF A.1/54 THEN M ELSE N/A
IF A.1/55 THEN M ELSE N/A
IF A.1/56 THEN M ELSE N/A
IF C110 AND C118 THEN M ELSE N/A
C160
IF C110 AND C143 THEN M ELSE N/A
C161
IF C110 AND C145 THEN M ELSE N/A
C162
C163
C164
C165
C166
C167
C168
C169
C170
C171
C172
C173
C174
C175
C176
C177
IF A.1/58 THEN M ELSE N/A
IF A.1/58 AND A.1/60 THEN M ELSE N/A
IF A.1/61 THEN M ELSE N/A
IF A.1/62 THEN M ELSE N/A
IF A.1/63 THEN M ELSE N/A
IF A.1/64 THEN M ELSE N/A
IF A.1/65 THEN M ELSE N/A
IF A.1/66 THEN M ELSE N/A
IF A.1/67 THEN M ELSE N/A
IF A.1/68 THEN M ELSE N/A
IF A.1/69 THEN M ELSE N/A
IF A.1/70 THEN M ELSE N/A
IF A.1/71 THEN M ELSE N/A
IF A.1/72 THEN M ELSE N/A
IF A.1/73 THEN M ELSE N/A
IF A.1/74 THEN M ELSE N/A
ETSI TS 102 384 V10.3.0 (2015-08)
-- O_Tones
-- O_Batt
-- O_Ucs2_Entry AND O_UCS2_Chinese
-- O_Ucs2_Disp AND O_UCS2_Chinese
-- O_Ucs2_Entry AND O_UCS2_Katakana
-- O_Ucs2_Disp AND O_UCS2_Katakana
-- O_TAT_AL
-- O_TAT_AC
-- O_TAT_AR
-- O_TAT_FSN
-- O_TAT_FSL
-- O_TAT_FSS
-- O_TAT_SN
-- O_TAT_SB
-- O_TAT_SI
-- O_TAT_SU
-- O_TAT_SS
-- O_TAT_STFC
-- O_TAT_STBC
-- O_Run_At AND O_+CGMI AND O_Ucs2_Disp AND
O_Ucs2_Disp_Cyrillic
-- O_Run_At AND O_+CGMI AND O_Ucs2_Disp AND
O_Ucs2_Disp_Chinese
-- O_Run_At AND O_+CGMI AND O_Ucs2_Disp AND
O_Ucs2_Disp_Katakana
-- O_TCP_UICC_ServerMode
-- O_TCP_UICC_ServerMode AND O_BUFFER_SIZE
-- O_TCP_Terminal_ServerMode
-- O_UDP_Terminal_ServerMode
-- O_Terminal_Applications
-- O_Activate
-- O_HCI_Connectivity_Event
-- O_Broadcast_Network
-- O_No_Type_ND
-- O_No_Type_NK
-- O_No_Type_NA
-- O_No_Type_NS
-- O_No_Type_NL
-- O_CL_State_CR
-- O_Terminal_ServerMode_Confirm_Param
-- O_Direct_Com_Channel
ETSI
Release 10
55
O.1
O.2
O.3
ETSI TS 102 384 V10.3.0 (2015-08)
IF (the Terminal supports icons as defined in record 1 of EF(IMG), tests x.1A M ELSE tests x.1B M (where
x is the expected sequence number value).
IF the Terminal supports icons as defined in record 2 of EF(IMG), tests x.2A M ELSE x.2B M (where x is
the expected sequence number value).
Void.
ETSI
Release 10
56
3.5
Conventions for mathematical notations
3.5.1
Mathematical signs
ETSI TS 102 384 V10.3.0 (2015-08)
The conventions for mathematical notations specified below apply:
•
The "plus or minus" sign is expressed by "±".
•
The sign "multiplied by" is expressed by "*".
•
The sign "divided by" is expressed by "/", or the common division bar.
•
The sign "greater than or equal to" is expressed by "≥".
•
The sign "less than or equal to" is expressed by "≤".
3.6
Abbreviations
For the purposes of the present document, the abbreviations given in ETSI TS 102 223 [1], ETSI TS 127 007 [6], ETSI
TS 101 267 [11] and the following apply:
CLA
CLF
CLI
CSG
DF
HCI
HSDPA
ICCID
INS
LOCI
MF
NA
ND
NK
NL
NS
PL
PLMN
RF
RP
SIM
SM
SN
SWP
TA
TBD
TE
TR
USB
WLAN
4
CLAss
ContactLess Frontend
Calling Line Identifier
Closed Subscriber Group
Dedicated File
Host Controller Interface
High Speed Downlink Packet Access
Integrated Circuit Card IDentification
INStruction
LOCation Information
Master File
No Audio
No Display
No Keypad
No support for multiple Languages
No Speech capability
Preferred Languages
Public Land Mobile Network
Radio Frequency
Radio Path
Subscriber Identity Module
ShortMessage
Short Message
Single Wire Protocol
Terminal Adaptor
To Be Defined
Terminal Equipment
TEMINAL RESPONSE
Universal Serial Bus
Wireless ocal Area Network
Test equipment
The test equipment depends on the NAA of the test environment.
ETSI
Release 10
57
ETSI TS 102 384 V10.3.0 (2015-08)
5
Testing methodology in general
5.1
Testing of optional functions and procedures
Any function or procedure which is optional, as indicated in the present document, may be subject to a conformance test
if it is implemented in the Terminal.
5.2
Test interfaces and facilities
The UICC interface provides the main test interfaces for the purpose of performing conformance tests.
The tests which require a network simulator shall not be carried out in this present document as the tests are intended to
be independent of the NAA.
5.3
Information to be provided by the apparatus supplier
The information to be provided by the apparatus supplier specified in this present document shall apply.
In addition, the apparatus supplier shall provide the information with respect to the Supported Option table A.1 and to
Terminal's default configuration table A.2.
Table A.2: Terminal's default configuration
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
NOTE:
Description
Value
DISPLAY TEXT No Response from user timeout interval
GET INKEY No Response from user timeout interval
GET INPUT No Response from user timeout interval
SELECT ITEM No Response from user timeout interval
DISPLAY TEXT Text Attribute Alignment (Left or Center or Right)
GET INKEY Text Attribute Alignment (Left or Center or Right)
GET INPUT Text Attribute Alignment (Left or Center or Right)
PLAY TONE Text Attribute Alignment (Left or Center or Right)
SET UP MENU Text Attribute Alignment (Left or Center or Right)
SELECT ITEM Text Attribute Alignment (Left or Center or Right)
SEND SHORT MESSAGE Text Attribute Alignment (Left or Center or Right)
Void
Void
SET UP CALL Text Attribute Alignment (Left or Center or Right)
SET UP IDLE MODE TEXT Text Attribute Alignment (Left or Center or Right)
RUN AT COMMAND Text Attribute Alignment (Left or Center or Right)
SEND DTMF Text Attribute Alignment (Left or Center or Right)
LAUNCH BROWSER Text Attribute Alignment (Left or Center or Right)
OPEN CHANNEL Text Attribute Alignment (Left or Center or Right)
CLOSE CHANNEL Text Attribute Alignment (Left or Center or Right)
RECEIVE DATA Text Attribute Alignment (Left or Center or Right)
SEND DATA Text Attribute Alignment (Left or Center or Right)
IMEI
IMEISV
ESN
Additional Card Reader ID
Channel ID
Manufacturer identification as implemented according to ETSI TS 127 007 [6], clause 5.1
Preferred buffer size supported by the terminal for Open Channel command
Conditional values shall be provided if the corresponding option is supported in the table A.1.
ETSI
Status
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Release 10
58
6
Void
7
Measurement uncertainty
ETSI TS 102 384 V10.3.0 (2015-08)
The measured value relating to the corresponding limit shall be used to determine whether or not a terminal equipment
meets the requirement (ETSI ETR 028 [i.1], annex B).
This process is often referred to as "shared risk".
8
Format of tests
In general the following basic format for tests is used:
27.22.X.X.
Tested command
27.22.X.X.1
Command tested in «environment #1" (NORMAL, ICONS, UCS2 …)
27.22.X.X.1.1
Definition and applicability
This clause refers back to clause 3.2.2.
27.22.X.X.1.2
Conformance requirement
Only if required, this clause details the necessary core specification references.
27.22.X.X.1.3
Test purpose
This clause details the purpose of the test.
27.22.X.X.1.4
Method of test
27.22.X.X.1.4.1
Initial conditions
If present this clause defines the initial conditions to be established before running each test
sequence.
27.22.X.X.1.4.2
Procedure
This clause details the test procedure. Each test sequence shall be carried out independently unless
otherwise stated.
Sequence 1.1 (further initial conditions, added here)
Command 1.1.1
TERMINAL RESPONSE1.1.1A or 1.1.1B
Command 1.1.2
TERMINAL RESPONSE1.1.2
PROACTIVE COMMAND 1.1.1
TERMINAL RESPONSE 1.1.1A
TERMINAL RESPONSE 1.1.1B
PROACTIVE COMMAND 1.1.2
TERMINAL RESPONSE 1.1.2
ETSI
Release 10
59
ETSI TS 102 384 V10.3.0 (2015-08)
Sequence 1.2
Command 1.2.1
TERMINAL RESPONSE 1.2.1
Command 1.2.2
TERMINAL RESPONSE1.2.2 (same as TERMINAL RESPONSE 1.2.1)
Command 1.2.3
TERMINAL RESPONSE 1.2.3
PROACTIVE COMMAND 1.2.1
PROACTIVE COMMAND 1.2.2
PROACTIVE COMMAND 1.2.3
TERMINAL RESPONSE 1.2.1
TERMINAL RESPONSE 1.2.2
TERMINAL RESPONSE 1.2.3
Sequence 1.3
Command 1.3.1
TERMINAL RESPONSE1.3.1
PROACTIVE COMMAND 1.3.1
TERMINAL RESPONSE 1.3.1
27.22.X.X.1.5
Test requirement
This clause details the conditions to be met for successful completion of the test.
27.22.X.X.2
Command tested in "environment #2" (NORMAL, ICONS, UCS2 …)
27.22.X.X. 2.1
Definition and applicability
27.22.X.X. 2.2
Conformance requirement
27.22.X.X. 2.3
Test purpose
27.22.X.X. 2.4
Method of test
27.22.X.X. 2.4.1.1 Initial conditions
27.22.X.X. 2.4.1.2 Procedure
Sequence 2.1
Command 2.1.1
TERMINAL RESPONSE2.1.1A or 2.1.1B
Command 2.1.2
TERMINAL RESPONSE2.1.2
PROACTIVE COMMAND 2.1.1
TERMINAL RESPONSE 2.1.1A
TERMINAL RESPONSE 2.1.1B
PROACTIVE COMMAND 2.1.2
TERMINAL RESPONSE 2.1.2
ETSI
Release 10
60
ETSI TS 102 384 V10.3.0 (2015-08)
Sequence 2.2
Command 2.2.1
TERMINAL RESPONSE 2.2.1
Command 2.2.2
TERMINAL RESPONSE 2.2.2 (same as TERMINAL RESPONSE 2.2.1)
Command 2.2.3
TERMINAL RESPONSE 2.2.3
PROACTIVE COMMAND 2.2.1
PROACTIVE COMMAND 2.2.2
PROACTIVE COMMAND 2.2.3
Coding TERMINAL RESPONSE 2.2.1
Coding TERMINAL RESPONSE 2.2.2
Coding TERMINAL RESPONSE 2.2.3
27.22.X.X.2.5
9
Test requirement
Generic call set up procedures
The generic call set up procedure is not specified in this present document as this procedure is NAA dependent.
10 to 26 Void
27
Testing of the UICC/Terminal interface
27.0
General
This clause is to confirm the correct interpretation of the Card Application Toolkit commands and the correct operation
of the Toolkit facilities.
The definitions, declarations and default values specified in this present document shall apply.
A UICC Simulator with the appropriate Card Application Toolkit functionality will be required. The UICC data defined
below shall be used for all test cases unless otherwise specified within the test case.
The comprehension required flags in SIMPLE-TLV objects that are included in a TERMINAL RESPONSE or an
ENVELOPE shall be set as described in ETSI TS 102 223 [1]. This means that in cases where it is up to the Terminal to
decide if this flag is used or not, the corresponding Tag coding in the TERMINAL RESPONSEs and ENVELOPEs in
the present document represents only one of the two valid possibilities.
27.1 to 27.21 Void
ETSI
Release 10
27.22
61
ETSI TS 102 384 V10.3.0 (2015-08)
Card Application Toolkit
27.22.1a General Test purpose
Testing of functional conformance to Card Application Toolkit commands includes proactive UICC commands.
All facilities independent from a specific NAA given by the TERMINAL PROFILE as supported, for which tests exist
in the present document, shall be tested.
Many of the proactive UICC commands include an alpha identifier data object. This is intended to be a short one or two
word identifier for the Terminal to optionally display on the screen along with any other indications, at the same time as
the Terminal performs the UICC command.
NOTE:
The sequence of Card Application Toolkit commands are specific to the Toolkit Application being
executed within the UICC, hence sequential testing of commands is not possible. The testing will
therefore have to be performed on a command by command basis.
27.22.1b Definition of default values for Card Application Toolkit testing
A UICC containing the following default values is used for all tests of this clause unless otherwise stated.
For each item, the logical default values and the coding within the Elementary Files (EF) of the UICC as follows:
NOTE 1: Bx represents byte x of the coding.
NOTE 2: Unless otherwise defined, the coding values in binary.
EFICCID (ICCID, 2FE2)
Logically:
Identification number: 8949000202140000045
Coding:
Coding:
98
94
00
20
20
41
00
00
40
F5
For the display of icon:
•
Under the DF Telecom: creation of DF Graphics (5F50);
•
Under the DF 5F50: creation of EFImg (4F20, linear fixed file) and EFInstance (4FXX, transparent file).
EFImg (Image, 4F20)
Record 1:
Logically:
Number of Actual Images Instances:
Image Instance Width:
Image Instance Height:
Image Coding Scheme:
Image Instance File Identifier:
Offset into Image Instance File:
Length of Image Instance Data:
01
08
08
11 (basic image)
4F 04 (EFInstance)
00 00
00 0A
Coding:
Coding:
01
FF
08
FF
08
FF
11
FF
4F
FF
04
FF
ETSI
00
FF
00
FF
00
0A
FF
FF
Release 10
62
ETSI TS 102 384 V10.3.0 (2015-08)
Record 2:
Logically:
Number of Actual Images Instances:
Image Instance Width:
Image Instance Height:
Image Coding Scheme:
Image Instance File Identifier:
Offset into Image Instance File:
Length of Image Instance Data:
01
08
08
21 (colour image)
4F 02(EFInstance)
00 00
00 16
Coding:
Coding:
01
FF
08
FF
08
FF
21
FF
4F
FF
02
FF
00
FF
00
FF
00
16
FF
FF
03
FF
00
FF
00
FF
00
32
FF
FF
01
FF
00
FF
00
FF
00
E8
FF
FF
Record 3:
Logically:
Number of Actual Images Instances:
Image Instance Width:
Image Instance Height:
Image Coding Scheme:
Image Instance File Identifier:
Offset into Image Instance File:
Length of Image Instance Data:
01
18
10
11 (basic image)
4F 03 (EFInstance)
00 00
00 32
Coding:
Coding:
01
FF
18
FF
10
FF
11
FF
4F
FF
Record 4:
Logically:
Number of Actual Images Instances:
Image Instance Width:
Image Instance Height:
Image Coding Scheme:
Image Instance File Identifier:
Offset into Image Instance File:
Length of Image Instance Data:
01
2E
28
11 (basic image)
4F 01 (EFInstance)
00 00
00 E8
Coding:
Coding:
01
FF
2E
FF
28
FF
11
FF
4F
FF
Record 5:
Logically:
Number of Actual Images Instances:
Image Instance Width:
Image Instance Height:
Image Coding Scheme:
Image Instance File Identifier:
Offset into Image Instance File:
Length of Image Instance Data:
01
05
05
11 (basic image)
4F 05 (EFInstance)
00 00
00 08
ETSI
Release 10
63
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
Coding:
01
FF
05
FF
05
FF
11
FF
4F
FF
05
FF
00
FF
00
FF
00
08
FF
FF
00
FF
F8
80
38
40
00
00
00
00
06
6F
FF
FE
F8
00
EE
80
00
00
00
00
00
00
00
00
00
6F
6F
FF
FE
E0
00
00
00
00
07
4A
00
00
00
00
00
00
06
6D
FF
FE
E6
20
F0
00
00
00
48
14
24
00
00
00
00
06
6B
FF
EE
E4
40
04
40
00
00
00
00
C4
45
89
00
00
06
6B
BF
F6
E4
40
04
40
00
00
00
03
00
00
31
15
32
01
77
FF
F6
60
00
04
40
00
00
00
01
1B
00
00
00
92
43
20
FF
FE
E0
BC
20
80
00
00
00
01
1B
BF
FF
0C
00
00
20
80
01
80
00
00
00
00
00
00
01
1B
BF
FF
F8
80
00
00
00
01
12
C8
00
81
00
16
52
00
AA
80
FF
AA
02
80
AA
02
AA
85
FF
42
00
EFInstance (4F01)
Logically:
Image Instance Data:
see below
Coding:
Coding:
2E
00
00
00
00
00
01
1B
BF
FF
F9
88
66
80
00
00
1C
25
71
9E
28
00
00
00
01
1A
A0
FF
F9
90
01
10
00
00
00
00
21
11
1C
24
00
00
01
1A
AF
FD
1F
90
01
10
00
00
00
00
1F
00
08
45
4D
4E
00
0F
BF
03
D8
80
02
10
00
00
00
00
06
7F
FF
00
44
50
08
E0
EFInstance (4F02)
Logically:
Image Instance Data:
Image width:
Image length:
Bits per raster image point:
Number of CLUT entries:
Location of CLUT:
Image body:
08
08
02
03
00 16
see below
Coding:
Coding:
08
81
00
08
42
00
02
81
FF
03
42
00
EFInstance (4F03)
Logically:
Image Instance Data:
see below
ETSI
Release 10
64
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
Coding:
18
00
20
3C
FF
10
01
F1
F1
FF
FF
8F
89
80
FF
3C
20
00
FF
F1
11
01
80
89
89
80
00
20
20
00
01
81
11
01
80
89
89
80
00
20
20
00
01
81
11
01
03
A5
99
99
A5
C3
FF
FE
EB
BF
FF
FF
FF
80
89
8F
FF
EFInstance (4F04)
Logically:
Image Instance Data:
see below
Coding:
Coding:
08
08
FF
EFInstance (4F05)
Logically:
Image Instance Data:
see below
Coding:
Coding:
05
05
27.22.1 Initialization of Card Application Toolkit Enabled UICC by Card
Application Toolkit Enabled Terminal (Profile Download)
27.22.1.1
Definition and applicability
See clause 3.2.2.
27.22.1.2
Conformance requirement
The Terminal shall support the PROFILE DOWNLOAD command as defined in:
•
ETSI TS 102 223 [1], clause 5.2.
27.22.1.3
Test purpose
To verify that the Terminal sends a TERMINAL PROFILE command in accordance with the above requirements.
27.22.1.4
27.22.1.4.1
Method of test
Initial conditions
The Terminal is connected to the UICC Simulator. All elementary files are coded as the default Toolkit personalization.
27.22.1.4.2
Procedure
Expected Sequence 1 (PROFILE DOWNLOAD)
Step
1
2
3
4
5
6
Direction
USER → Terminal
Terminal → UICC
UICC → Terminal
Terminal → UICC
UICC → Terminal
Terminal → UICC
Message/Action
Comments
Power on Terminal
UICC Activation.
Select EF PL
Read EF PL
TERMINAL PROFILE 1.1
PROFILE DOWNLOAD.
NORMAL ENDING OF COMMAND 1.1
Select NAA Application
ETSI
Release 10
65
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL PROFILE: 1.1
Logically:
Coding:
APDU:
CLA=80
DATA IN:
INS=10
P1=00
YY
ZZ
P2=00
P3=XX
…
With XX representing the length of the following DATA IN depending on the Card Toolkit commands supported by the
Terminal, and with YY, ZZ, … representing here the bytes of the TERMINAL PROFILE data, as specified in ETSI
TS 102 223 [1], clause 5.2.
NORMAL ENDING OF COMMAND: 1.1
Logically:
Coding:
SW1=90
27.22.1.5
SW2=00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 1.
27.22.2 Contents of the TERMINAL PROFILE command
27.22.2.1
Definition and applicability
See table E.1 in annex B.
27.22.2.2
Conformance requirement
The Terminal shall support the PROFILE DOWNLOAD command as defined in:
•
ETSI TS 102 223 [1], clause 5.2.
27.22.2.3
Test purpose
1)
Verify that the TERMINAL PROFILE indicates that Profile Download facility is supported.
2)
Record which Card Application Toolkit facilities are supported by the Terminal, to determine which
subsequent tests are required.
27.22.2.4
27.22.2.4.1
Method of test
Initial conditions
The Terminal is connected to the UICC Simulator. All elementary files are coded as the default Card Application
Toolkit personalization.
27.22.2.4.2
Procedure
a)
The Terminal is powered on.
b)
After the Terminal sends the TERMINAL PROFILE command to the UICC Simulator, the UICC Simulator
shall record the content of the TERMINAL PROFILE.
c)
The UICC Simulator shall return SW1/SW2 of '90 00'.
d)
The contents of the TERMINAL PROFILE is recorded and compared to the corresponding table E.1 "status"
column.
ETSI
Release 10
66
ETSI TS 102 384 V10.3.0 (2015-08)
The test is terminated upon the Terminal sending the TERMINAL PROFILE command to the UICC Simulator.
27.22.2.5
Test requirement
1)
After step a) the Terminal shall send the TERMINAL PROFILE command to the UICC Simulator with bit 1 of
the first byte set to 1 (facility supported by Terminal).
2)
In table E.1 for the corresponding Terminal Card Toolkit Release and Options, The TERMINAL PROFILE
information "support" recorded shall be in accordance with the "Status" column. Support of features defined
only in releases later than present release shall be ignored.
27.22.3 Servicing of proactive UICC commands
27.22.3.1
Definition and applicability
See clause 3.2.2.
27.22.3.2
Conformance requirement
On detection of a pending Card Application Toolkit command from the UICC the Terminal shall perform the FETCH
command to retrieve the proactive UICC command. The result of the executed command shall be transmitted from the
Terminal to the UICC within a TERMINAL RESPONSE command.
The MORE TIME proactive command is used in this test. The Terminal shall have knowledge of this command, but
may not support this Card Application Toolkit facility.
•
ETSI TS 102 223 [1], clause 6.3.
27.22.3.3
Test purpose
To verify that the Terminal uses the FETCH command to obtain the proactive UICC command, after detection of a
pending proactive UICC command. The pending proactive UICC command is indicated by the response parameters
'91 xx' from the UICC.
To verify that the Terminal transmits the result of execution of the proactive UICC command to the UICC in the
TERMINAL RESPONSE command.
27.22.3.4
27.22.3.4.1
Method of test
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as the Card Application Toolkit default.
The UICC Simulator is configured to indicate that a proactive UICC command is pending.
The UICC Simulator is configured to monitor the UICC - Terminal interface.
27.22.3.4.2
Procedure
a)
The Terminal is powered on.
b)
After the Terminal has performed the PROFILE DOWNLOAD procedure, the UICC Simulator indicates that a
Proactive UICC Command is pending with SW1/SW2 of '91 0B'.
c)
After the Terminal sends the FETCH command to the UICC Simulator, the UICC Simulator returns Proactive
UICC Command 2.1: MORE TIME.
27.22.3.5
Test requirement
1)
After step b) the Terminal shall send the FETCH command to the UICC.
2)
After step c) the Terminal shall send the TERMINAL REPONSE command with command number "01", type
of command "02" and command qualifier "00".
ETSI
Release 10
67
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4 Proactive UICC commands
27.22.4.1
DISPLAY TEXT
27.22.4.1.1
27.22.4.1.1.1
DISPLAY TEXT (Normal)
Definition and applicability
See clause 3.2.2.
27.22.4.1.1.2
Conformance requirements
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.31.
27.22.4.1.1.3
Test purpose
To verify that the Terminal displays the text contained in the DISPLAY TEXT proactive UICC command, and returns a
successful result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.1.4
Method of test
27.22.4.1.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.1.4.2
Procedure
Expected Sequence 1.1 (DISPLAY TEXT normal priority, Unpacked 8 bit data for Text String, successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.1.1
Terminal → USER Display "Toolkit Test 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
Normal priority, wait for user to clear
message, unpacked, 8 bit data.
Command performed successfully.
PROACTIVE COMMAND: DISPLAY TEXT 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
ETSI
Release 10
68
Text String
Data coding scheme:
Text:
"Toolkit Test 1"
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
Coding:
BER-TLV:
D0
0F
73
1A
04
74
81
54
20
03
6F
31
01
6F
21
6C
80
6B
82
69
02
74
81
20
02
54
8D
65
01
00
TERMINAL RESPONSE: DISPLAY TEXT 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
Expected Sequence 1.2 (DISPLAY TEXT normal priority, Unpacked 8 bit data for Text String, screen busy)
Step
1
2
3
4
5
6
7
Direction
Message/Action
USER → Terminal Set the Terminal screen to a
display mode other than the
normal stand-by display
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.2.1
Terminal → USER No change of the currently being
used display.
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
The Terminal will be set to a mode so that
normal priority text commands shall be
rejected.
Normal priority.
Terminal currently unable to process
command - screen busy.
PROACTIVE COMMAND: DISPLAY TEXT 1.2.1: same as 1.1.1
TERMINAL RESPONSE: DISPLAY TEXT 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
69
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Additional information:
Terminal currently unable to process command
Screen is busy
Coding:
BER-TLV:
81
01
03
01
21
80
82
02
82
81
83
02
20
Expected Sequence 1.3 (DISPLAY TEXT, high priority, Unpacked 8 bit data for Text String, successful)
Step
1
2
3
4
5
6
7
8
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.3.1
Terminal → USER Display "Toolkit Test 2"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.3.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Set the Terminal screen back to
normal stand-by display
Comments
The Terminal screen is in a mode other than
the normal stand by display.
High priority.
PROACTIVE COMMAND: DISPLAY TEXT 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
high priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Toolkit Test 2"
Coding:
BER-TLV:
D0
0F
73
1A
04
74
81
54
20
03
6F
32
01
6F
21
6C
81
6B
82
69
TERMINAL RESPONSE: DISPLAY TEXT 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
high priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
02
74
81
20
02
54
8D
65
Release 10
70
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
81
82
02
82
81
83
01
00
Expected Sequence 1.4 (DISPLAY TEXT, Packed, SMS default alphabet, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING: DISPLAY
TEXT 1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: DISPLAY TEXT 1.4.1
Terminal → USER Display "Toolkit Test 3"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE: DISPLAY TEXT 1.4.1
Comments
Packed, SMS default alphabet.
Command performed successfully.
PROACTIVE COMMAND: DISPLAY TEXT 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text string
Data coding scheme:
Text:
packed, SMS default alphabet
"Toolkit Test 3"
Coding:
BER-TLV:
D0
0E
0E
19
00
9A
81
D4
01
03
F7
01
9B
21
BD
80
4E
82
D3
02
41
81
D4
02
F2
8D
9C
01
00
TERMINAL RESPONSE: DISPLAY TEXT 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
ETSI
02
82
81
83
Release 10
71
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.5 (DISPLAY TEXT, Clear message after delay, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING: DISPLAY
TEXT 1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: DISPLAY TEXT 1.5.1
Terminal → USER Display "Toolkit Test 4" and clear this message
after a short delay
Terminal → UICC TERMINAL RESPONSE: DISPLAY TEXT 1.5.1
UICC → Terminal PROACTIVE UICC SESSION ENDED
Comments
Clear message after a delay.
Command performed successfully.
PROACTIVE COMMAND: DISPLAY TEXT 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, clear message after a delay
Device identities
Source device:
Destination device:
UICC
Display
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"Toolkit Test 4"
Coding:
BER-TLV:
D0
0F
73
1A
04
74
81
54
20
03
6F
34
01
6F
21
6C
00
6B
82
69
02
74
81
20
02
54
8D
65
01
00
TERMINAL RESPONSE: DISPLAY TEXT 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, clear message after a delay
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
00
82
ETSI
02
82
81
83
Release 10
72
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.6 (DISPLAY TEXT, Text string with 160 bytes, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.6.1
Terminal → USER Display "This command instructs
the ME to display a text message.
It allows the SIM to define the
priority of that message, and the
text string format. Two types of
prio"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.6.1
Comments
Text string with 160 bytes - maximum for non
extension text.
Command performed successfully.
PROACTIVE COMMAND: DISPLAY TEXT 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"This command instructs the ME to display a text message. It allows
the SIM to define the priority of that message, and the text string
format. Two types of prio"
Coding:
BER-TLV:
D0
8D
6D
74
20
65
20
68
66
6F
74
6E
73
74
20
81
81
61
73
64
78
49
65
69
72
20
64
74
2E
6F
AD
A1
6E
20
69
74
74
20
6E
69
6D
20
72
20
66
81
04
64
74
73
20
20
53
65
74
65
74
69
54
20
03
54
20
68
70
6D
61
49
20
79
73
68
6E
77
70
01
68
69
65
6C
65
6C
4D
74
20
73
65
67
6F
72
21
69
6E
20
61
73
6C
20
68
6F
61
20
20
20
69
80
73
73
4D
79
73
6F
74
65
66
67
74
66
74
6F
82
20
74
45
20
61
77
6F
20
20
65
65
6F
79
02
63
72
20
61
67
73
20
70
74
2C
78
72
70
TERMINAL RESPONSE: DISPLAY TEXT 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
ETSI
81
6F
75
74
20
65
20
64
72
68
20
74
6D
65
02
6D
63
6F
74
2E
74
65
69
61
61
20
61
73
Release 10
73
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
01
00
Expected Sequence 1.7 (DISPLAY TEXT, Backward move in Proactive UICC session, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.7.1
Terminal → USER Display "<GO-BACKWARDS>"
USER → Terminal Indicate the need to go backwards
in the proactive UICC application
session
Backward move in the proactive UICC
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.7.1
session requested by the user.
PROACTIVE COMMAND: DISPLAY TEXT 1.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"<GO-BACKWARDS>"
Coding:
BER-TLV:
D0
0F
52
1A
04
44
81
3C
53
03
47
3E
01
4F
21
2D
80
42
82
41
02
43
81
4B
TERMINAL RESPONSE: DISPLAY TEXT 1.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
02
57
8D
41
Release 10
74
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Backward move in the proactive UICC session requested by the user
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
01
11
Expected Sequence 1.8 (DISPLAY TEXT, session terminated by user)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.8.1
Terminal → USER Display "<ABORT>"
USER → Terminal Indicate the need to end the
proactive UICC application session
Proactive UICC session terminated by the
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.8.1
user.
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: DISPLAY TEXT 1.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"<ABORT>"
Coding:
BER-TLV:
D0
08
13
04
81
3C
03
41
01
42
21
4F
80
52
82
54
02
3E
81
TERMINAL RESPONSE: DISPLAY TEXT 1.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Proactive UICC session terminated by the user
ETSI
02
8D
Release 10
75
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
01
10
Expected Sequence 1.9 (DISPLAY TEXT, icon and text to be displayed, no text string given, not understood by
Terminal)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.9.1
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
Including icon identifier, icon shall be
displayed together with the alpha text string,
but no text string given.
Command data not understood by Terminal
(clause 6.5.4).
PROACTIVE COMMAND: DISPLAY TEXT 1.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text string
Contents:
null data object
Icon Identifier:
Icon qualifier:
Icon Identifier:
icon is self-explanatory
record 1 in EF(IMG)
Coding:
BER-TLV:
D0
00
0F
9E
81
02
03
00
01
01
21
80
82
02
81
TERMINAL RESPONSE: DISPLAY TEXT 1.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command data not understood by Terminal
ETSI
02
8D
Release 10
76
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
27.22.4.1.1.5
81
03
01
21
80
82
02
82
81
83
01
32
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.9.
27.22.4.1.2
27.22.4.1.2.1
DISPLAY TEXT (Support of "No response from user")
Definition and applicability
See clause 3.2.2.
27.22.4.1.2.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
27.22.4.1.2.3
Test purpose
To verify that the Terminal displays the text contained in the DISPLAY TEXT proactive UICC command, and returns a
"No response from user" result value in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.2.4
Method of test
27.22.4.1.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
Terminal Manufacturers shall set the "no response from user" period of time as declared in table A.2/1.
The UICC Simulator shall be set to that period of time.
27.22.4.1.2.4.2
Procedure
Expected Sequence 2.1 (DISPLAY TEXT, no response from user)
Step
1
2
3
4
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 2.1.1
Terminal → USER Display "<TIME-OUT>"
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 2.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
Normal priority, wait for user to clear
message, unpacked, 8 bit data.
No response from user within 5 s after the end
of that defined period of time.
PROACTIVE COMMAND: DISPLAY TEXT 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
ETSI
Release 10
77
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Display
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"<TIME-OUT>"
Coding:
BER-TLV:
D0
0B
16
04
81
3C
03
54
01
49
21
4D
80
45
82
2D
02
4F
81
55
02
54
8D
3E
01
12
TERMINAL RESPONSE: DISPLAY TEXT 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
No response from user
Coding:
BER-TLV:
27.22.4.1.2.5
81
03
01
21
80
82
02
82
81
83
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.1.3
27.22.4.1.3.1
DISPLAY TEXT (Display of extension text)
Definition and applicability
See clause 3.2.2.
27.22.4.1.3.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.6.1, 6.8, 6.11, 8.6 and 8.15.
27.22.4.1.3.3
Test purpose
To verify that the Terminal displays the extension text contained in the DISPLAY TEXT proactive UICC command,
and returns a successful result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.3.4
Method of test
27.22.4.1.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
78
27.22.4.1.3.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 3.1 (DISPLAY TEXT, display of the extension text)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 3.1.1
Terminal → UICC FETCH
Text string with the maximum of 240 bytes.
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 3.1.1
Terminal → USER Display "This command instructs
the ME to display a text message,
and/or an icon (see 6.5.4). It allows
the SIM to define the priority of that
message, and the text string
format. Two types of priority are
defined:- display normal priority
text and/"
USER → Terminal Clear Message
Command performed successfully.
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 3.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: DISPLAY TEXT 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"This command instructs the ME to display a text message and/or an
icon (see 6.5.4). It allows the SIM to define the priority of that
message, and the text string format. Two types of priority are
defined:- display normal priority text and/"
Coding:
BER-TLV:
D0
8D
6D
74
20
65
20
63
2E
77
6F
20
20
65
65
6F
79
72
69
81
81
61
73
64
78
61
6F
34
73
20
70
74
2C
78
72
70
69
6E
FD
F1
6E
20
69
74
6E
6E
29
20
64
72
68
20
74
6D
65
74
65
81
04
64
74
73
20
64
20
2E
74
65
69
61
61
20
61
73
79
64
03
54
20
68
70
6D
2F
28
20
68
66
6F
74
6E
73
74
20
20
3A
01
68
69
65
6C
65
6F
73
49
65
69
72
20
64
74
2E
6F
61
2D
ETSI
21
69
6E
20
61
73
72
65
74
20
6E
69
6D
20
72
20
66
72
20
80
73
73
4D
79
73
20
65
20
53
65
74
65
74
69
54
20
65
64
82
20
74
45
20
61
61
20
61
49
20
79
73
68
6E
77
70
20
69
02
63
72
20
61
67
6E
36
6C
4D
74
20
73
65
67
6F
72
64
73
81
6F
75
74
20
65
20
2E
6C
20
68
6F
61
20
20
20
69
65
70
02
6D
63
6F
74
2C
69
35
6F
74
65
66
67
74
66
74
6F
66
6C
Release 10
79
61
69
61
79
6F
6E
20
72
64
6E
69
2F
6F
74
ETSI TS 102 384 V10.3.0 (2015-08)
72
79
6D
20
61
74
6C
65
20
78
70
74
72
20
01
00
TERMINAL RESPONSE: DISPLAY TEXT 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.1.3.5
81
03
01
21
80
82
02
82
81
83
Test requirement
The Terminal shall operate in the manner defined in expected sequence 3.1.
27.22.4.1.4
27.22.4.1.4.1
DISPLAY TEXT (Sustained text)
Definition and applicability
See clause 3.2.2.
27.22.4.1.4.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.6.1, 6.8, 6.11, 8.6, 8.15 and 8.15.
27.22.4.1.4.3
Test purpose
To verify that the Terminal displays the text contained in the DISPLAY TEXT proactive UICC command, returns a
successful result in the TERMINAL RESPONSE command send to the UICC and sustain the display beyond sending
the TERMINAL response.
27.22.4.1.4.4
Method of test
27.22.4.1.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
80
27.22.4.1.4.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 4.1 (DISPLAY TEXT, sustained text, unpacked data 8 bits, successful)
Step
1
2
3
4
6
7
8
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 4.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 4.1.1
Terminal → USER Display "Toolkit Test 1"
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 4.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Terminal → USER Display of "Toolkit Test 1" shall
sustain
Comments
Normal priority, wait for user to clear
message, unpacked, 8 bit data.
Command performed successfully.
Text shall sustain until - a subsequent
proactive command is received containing
display data.
PROACTIVE COMMAND: DISPLAY TEXT 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Toolkit Test 1"
Immediate Response
Coding:
BER-TLV:
D0
0F
73
1C
04
74
81
54
20
03
6F
31
01
6F
AB
21
6C
00
80
6B
82
69
02
74
81
20
02
54
8D
65
01
00
TERMINAL RESPONSE: DISPLAY TEXT 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
ETSI
02
82
81
83
Release 10
81
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 4.2 (DISPLAY TEXT, sustained text, clear message after delay, successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 4.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 4.2.1
Terminal → USER Display "Toolkit Test 2"
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 4.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Terminal → USER Display "Toolkit Test 2"
Comments
Clear message after a delay.
Command performed successfully.
Text shall sustain until - the expiration of a
short delay.
PROACTIVE COMMAND: DISPLAY TEXT 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, clear message after a delay
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Toolkit Test 2"
Immediate Response
Coding:
BER-TLV:
D0
0F
73
1C
04
74
81
54
20
03
6F
32
01
6F
AB
21
6C
00
00
6B
82
69
02
74
81
20
02
54
8D
65
01
00
TERMINAL RESPONSE: DISPLAY TEXT 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, clear message after a delay
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
00
82
ETSI
02
82
81
83
Release 10
82
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 4.3 (DISPLAY TEXT, sustained text, wait for user MMI to clear, successful)
Step
1
2
3
4
5
6
7
8
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 4.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 4.3.1
Terminal → USER Display "Toolkit Test 3"
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 4.3.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Terminal → USER Display of "Toolkit Test 3"
USER → Terminal Clear message
Comments
Wait for user to clear message.
Command performed successfully.
Text shall sustain until - a user MMI action.
PROACTIVE COMMAND: DISPLAY TEXT 4.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Toolkit Test 3"
Immediate Response
Coding:
BER-TLV:
D0
0F
73
1C
04
74
81
54
20
03
6F
33
01
6F
AB
21
6C
00
80
6B
82
69
02
74
81
20
02
54
8D
65
01
00
TERMINAL RESPONSE: DISPLAY TEXT 4.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
ETSI
02
82
81
83
Release 10
83
27.22.4.1.4.5
ETSI TS 102 384 V10.3.0 (2015-08)
Test requirement
The Terminal shall operate in the manner defined in expected sequences 4.1 to 4.3.
27.22.4.1.5
27.22.4.1.5.1
DISPLAY TEXT (Display of icons)
Definition and applicability
See clause 3.2.2.
27.22.4.1.5.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.31.
27.22.4.1.5.3
Test purpose
To verify that the Terminal displays the icons which are referred to in the contents of the DISPLAY TEXT proactive
UICC command, and returns a successful result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.5.4
Method of test
27.22.4.1.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.5.4.2
Procedure
Expected Sequence 5.1A (DISPLAY TEXT, display of basic icon, self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 5.1.1
Terminal → USER Display the BASIC-ICON
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 5.1.1A
Comments
BASIC-ICON, self-explanatory
Command performed successfully
PROACTIVE COMMAND: DISPLAY TEXT 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Basic Icon"
Icon Identifier:
Icon qualifier:
Icon Identifier:
icon is self-explanatory
record 1 in EF(IMG)
ETSI
Release 10
84
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0B
9E
1A
04
02
81
42
00
03
61
01
01
73
21
69
80
63
82
20
02
49
81
63
02
6F
8D
6E
01
00
TERMINAL RESPONSE: DISPLAY TEXT 5.1.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
Expected Sequence 5.1B (DISPLAY TEXT, display of basic icon, self-explanatory, requested icon could not be
displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 5.1.1
Terminal → USER Display "Basic Icon" without icon
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 5.1.1B
Comments
BASIC-ICON, self-explanatory.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: DISPLAY TEXT 5.1.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully, but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
21
80
82
ETSI
02
82
81
83
01
04
Release 10
85
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 5.2A (DISPLAY TEXT, display of colour icon, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
PROACTIVE
COMMAND
UICC → Terminal
PENDING: DISPLAY TEXT 5.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 5.2.1
Terminal → USER Display the COLOUR-ICON
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 5.2.1A
Comments
COLOUR-ICON.
Command performed successfully.
PROACTIVE COMMAND: DISPLAY TEXT 5.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Colour Icon"
Icon Identifier:
Icon qualifier:
Icon Identifier:
icon is self-explanatory
record 2 in EF(IMG)
Coding:
BER-TLV:
D0
0C
6E
1B
04
9E
81
43
02
03
6F
00
01
6C
02
21
6F
80
75
82
72
02
20
81
49
02
63
8D
6F
01
00
TERMINAL RESPONSE: DISPLAY TEXT 5.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
ETSI
02
82
81
83
Release 10
86
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 5.2B (DISPLAY TEXT, display of colour icon, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
PROACTIVE
COMMAND
UICC → Terminal
PENDING: DISPLAY TEXT 5.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 5.2.1
Terminal → USER Display "Colour Icon" without the
icon
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 5.2.1B
Comments
COLOUR-ICON.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: DISPLAY TEXT 5.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully, but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
01
04
Expected Sequence 5.3A (DISPLAY TEXT, display of basic icon, not self explanatory, successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 5.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 5.3.1
Terminal → USER Display the BASIC-ICON
And
Display "Basic Icon"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 5.3.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
BASIC-ICON, not self-explanatory.
Command performed successfully.
PROACTIVE COMMAND: DISPLAY TEXT 5.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
ETSI
Release 10
87
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Basic Icon"
Icon Identifier:
Icon qualifier:
Icon Identifier:
icon is not self-explanatory
record 1 in EF(IMG)
Coding:
BER-TLV:
D0
0B
9E
1A
04
02
81
42
01
03
61
01
01
73
21
69
80
63
82
20
02
49
81
63
02
6F
8D
6E
01
00
TERMINAL RESPONSE: DISPLAY TEXT 5.3.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
Expected Sequence 5.3B (DISPLAY TEXT, display of basic icon, not self explanatory, requested icon could not
be displayed)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 5.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 5.3.1
Terminal → USER Display "Basic Icon" without the
icon
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 5.3.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
BASIC-ICON, not self-explanatory.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: DISPLAY TEXT 5.3.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
ETSI
Release 10
88
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully, but requested icon could not be
displayed
Coding:
BER-TLV:
27.22.4.1.5.5
81
03
01
21
80
82
02
82
81
83
01
04
Test requirement
The Terminal shall operate in the manner defined in expected sequences 5.1A to 5.3B.
27.22.4.1.6
27.22.4.1.6.1
DISPLAY TEXT (UCS2 display supported in Cyrillic)
Definition and applicability
See clause 3.2.2.
27.22.4.1.6.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.31.
The Terminal shall support the UCS2 alphabet for the coding of the Cyrillic alphabet, as defined in the following
technical specification: ISO/IEC 10646 [2].
27.22.4.1.6.3
Test purpose
To verify that the Terminal displays the text contained in the DISPLAY TEXT proactive UICC command, and returns a
successful result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.6.4
Method of test
27.22.4.1.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.6.4.2
Procedure
Expected Sequence 6.1 (DISPLAY TEXT, UCS2 coded in Cyrillic)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 6.1.1
Terminal → USER Display " ЗДРАВСТВУЙТЕ "
USER → Terminal Clear message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 6.1.1
ETSI
Comments
Normal priority, wait for user to clear
message, UCS2 coded.
"Hello" in Russian.
Release 10
89
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
UCS2 (16bit)
"ЗДРАВСТВУЙТЕ"
Coding:
BER-TLV:
D0
19
04
04
24
08
21
15
81
04
04
03
17
22
01
04
04
21
14
12
80
04
04
82
20
23
02
04
04
81
10
19
02
04
04
8D
12
22
01
00
TERMINAL RESPONSE: DISPLAY TEXT 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.1.6.5
81
03
01
21
80
82
02
82
81
83
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.1.
27.22.4.1.7
27.22.4.1.7.1
DISPLAY TEXT (Variable Time out)
Definition and applicability
See clause 3.2.2.
27.22.4.1.7.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31 and 8.43.
The Terminal shall support the variable time out for the display text.
ETSI
Release 10
90
27.22.4.1.7.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text contained in the DISPLAY TEXT proactive UICC command, and returns a
successful result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.7.4
Method of test
27.22.4.1.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.7.4.2
Procedure
Expected Sequence 7.1 (DISPLAY TEXT, variable timeout of 10 seconds)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 7.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 7.1.1
Comments
Normal priority, wait for user to clear
message, clear message after delay of 10
seconds.
Terminal → USER Display "10 Second" for 10
seconds
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 7.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
No response from user.
PROACTIVE COMMAND: DISPLAY TEXT 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"10 Second"
Duration
Time unit:
Time interval:
seconds
10 units
Coding:
BER-TLV:
D0
0A
02
19
04
01
81
31
0A
03
30
01
20
21
53
ETSI
80
65
82
63
02
6F
81
6E
02
64
8D
84
Release 10
91
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: DISPLAY TEXT 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
No response from user
Coding:
BER-TLV:
27.22.4.1.7.5
81
03
01
21
80
82
02
82
81
83
01
12
Test requirement
The Terminal shall operate in the manner defined in expected sequence 7.1.
27.22.4.1.8
DISPLAY TEXT (Support of Text Attribute)
27.22.4.1.8.1
DISPLAY TEXT (Support of Text Attribute - Left Alignment)
27.22.4.1.8.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.1.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with Left Alignment for the display text.
27.22.4.1.8.1.3
Test purpose
To verify that the Terminal displays the text formatted according to the left alignment text attribute configuration
contained in the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL
RESPONSE command send to the UICC.
27.22.4.1.8.1.4
Method of test
27.22.4.1.8.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.8.1.4.2
Procedure
Expected Sequence 8.1 (DISPLAY TEXT, Text Attribute with Left Alignment)
Step
1
2
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.1.1
Terminal → UICC FETCH
ETSI
Comments
Release 10
Step
3
4
5
6
7
8
9
10
11
12
92
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.1.1
Terminal → USER Display "Text Attribute 1"
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with left
alignment.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.1.2
Terminal → USER Display "Text Attribute 2"
Normal priority, wait for user to clear
message.
Message shall be formatted without left
alignment. Remark: If left alignment is the
Terminal's default alignment as declared in
table A.2/5, no alignment change will take
place.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.1.1
PROACTIVE COMMAND: DISPLAY TEXT 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
PROACTIVE COMMAND: DISPLAY TEXT 8.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
ETSI
02
72
00
8D
69
B4
Release 10
93
Text String
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"Text Attribute 2"
Coding:
BER-TLV:
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
82
41
02
74
81
74
02
72
8D
69
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.1.8.1.5
81
03
01
21
80
82
02
82
81
83
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.1.
27.22.4.1.8.2
DISPLAY TEXT (Support of Text Attribute - Center Alignment)
27.22.4.1.8.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.2.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with Centre Alignment for the display text.
27.22.4.1.8.2.3
Test purpose
To verify that the Terminal displays the text formatted according to the center alignment text attribute configuration
contained in the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL
RESPONSE command send to the UICC.
27.22.4.1.8.2.4
Method of test
27.22.4.1.8.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
94
27.22.4.1.8.2.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 8.2 (DISPLAY TEXT, Text Attribute with Center Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.2.1
Terminal → USER Display "Text Attribute 1"
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with center
alignment.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.2.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.2.2
Terminal → USER Display "Text Attribute 2"
Normal priority, wait for user to clear
message.
Message shall be formatted without center
alignment. Remark: If center alignment is the
Terminal's default alignment as declared in
table A.2/5, no alignment change will take
place.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.2.1
PROACTIVE COMMAND: DISPLAY TEXT 8.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
"Text Attribute 1"
unpacked, 8 bit data
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Center Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
ETSI
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
01
8D
69
B4
Release 10
95
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 8.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Coding:
BER-TLV:
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
82
41
02
74
81
74
02
72
8D
69
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.1.8.2.5
81
03
01
21
80
82
02
82
81
83
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.2.
27.22.4.1.8.3
DISPLAY TEXT (Support of Text Attribute - Right Alignment)
27.22.4.1.8.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.3.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with Right Alignment for the display text.
ETSI
Release 10
96
27.22.4.1.8.3.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text formatted according to the right alignment text attribute configuration
contained in the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL
RESPONSE command send to the UICC.
27.22.4.1.8.3.4
Method of test
27.22.4.1.8.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.8.3.4.2
Procedure
Expected Sequence 8.3 (DISPLAY TEXT, Text Attribute with Right Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.3.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.3.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.3.2
Terminal → USER Display "Text Attribute 2"
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with right
alignment.
Normal priority, wait for user to clear
message.
Message shall be formatted without right
alignment. Remark: If right alignment is the
Terminal's default alignment as declared in
table A.2/5, no alignment change will take
place.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.3.1
PROACTIVE COMMAND: DISPLAY TEXT 8.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
ETSI
Release 10
97
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
16
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
02
8D
69
B4
02
72
8D
69
01
00
PROACTIVE COMMAND: DISPLAY TEXT 8.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Coding:
BER-TLV:
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
82
41
02
74
81
74
TERMINAL RESPONSE: DISPLAY TEXT 8.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.1.8.3.5
81
03
01
21
80
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.3.
ETSI
82
81
83
Release 10
98
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4.1.8.4
DISPLAY TEXT (Support of Text Attribute - Large Font Size)
27.22.4.1.8.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.4.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with large font size for the display text.
27.22.4.1.8.4.3
Test purpose
To verify that the Terminal displays the text formatted according to the large size font text attribute configuration
contained in the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL
RESPONSE command send to the UICC.
27.22.4.1.8.4.4
Method of test
27.22.4.1.8.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.8.4.4.2
Procedure
Expected Sequence 8.4 (DISPLAY TEXT, Text Attribute with Large Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.4.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.4.2
Terminal → USER Display "Text Attribute 2"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.4.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.4.1
ETSI
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with large font
size.
Normal priority, wait for user to clear
message.
Message shall be formatted with normal font
size.
Normal priority, wait for user to clear
message.
Message shall be formatted with large font
size.
Release 10
Step
19
20
21
22
23
24
99
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.4.3
Terminal → USER Display "Text Attribute 3"
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with normal font
size.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.4.1
PROACTIVE COMMAND: DISPLAY TEXT 8.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
04
8D
69
B4
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
ETSI
02
82
81
83
Release 10
100
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 8.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font , Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
00
8D
69
B4
02
72
8D
69
PROACTIVE COMMAND: DISPLAY TEXT 8.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 3"
Coding:
BER-TLV:
27.22.4.1.8.4.5
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
33
80
20
82
41
02
74
81
74
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.4.
27.22.4.1.8.5
DISPLAY TEXT (Support of Text Attribute - Small Font Size)
27.22.4.1.8.5.1
Definition and applicability
See clause 3.2.2.
ETSI
Release 10
101
27.22.4.1.8.5.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with small font size for the display text.
27.22.4.1.8.5.3
Test purpose
To verify that the Terminal displays the text formatted according to the small size font text attribute configuration
contained in the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL
RESPONSE command send to the UICC.
27.22.4.1.8.5.4
Method of test
27.22.4.1.8.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.8.5.4.2
Procedure
Expected Sequence 8.5 (DISPLAY TEXT, Text Attribute with Small Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.5.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.5.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.5.2
Terminal → USER Display "Text Attribute 2"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.5.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.5.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.5.3
ETSI
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with small font
size.
Normal priority, wait for user to clear
message.
Message shall be formatted normal font size.
Normal priority, wait for user to clear
message.
Message shall be formatted with small font
size.
Normal priority, wait for user to clear
message.
Release 10
102
Step
22
Direction
Message/Action
Terminal → USER Display "Text Attribute 3"
23
24
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.5.1
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Message shall be formatted with normal font
size.
PROACTIVE COMMAND: DISPLAY TEXT 8.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
08
8D
69
B4
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
PROACTIVE COMMAND: DISPLAY TEXT 8.5.2
Logically:
Command details
Command number:
1
ETSI
02
82
81
83
Release 10
103
Command type:
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
00
8D
69
B4
02
72
8D
69
PROACTIVE COMMAND: DISPLAY TEXT 8.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 3"
Coding:
BER-TLV:
27.22.4.1.8.5.5
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
33
80
20
82
41
02
74
81
74
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.5.
27.22.4.1.8.6
DISPLAY TEXT (Support of Text Attribute - Bold On)
27.22.4.1.8.6.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.6.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with bold on for the display text.
ETSI
Release 10
104
27.22.4.1.8.6.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text formatted according to the bold text attribute configuration contained in the
DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL RESPONSE command
send to the UICC.
27.22.4.1.8.6.4
Method of test
27.22.4.1.8.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.8.6.4.2
Procedure
Expected Sequence 8.6 (DISPLAY TEXT, Text Attribute with Bold On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.6.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.6.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.6.2
Terminal → USER Display "Text Attribute 2"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.6.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.6.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.6.3
Terminal → USER Display "Text Attribute 3"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.6.1
ETSI
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with bold text on.
Normal priority, wait for user to clear
message.
Message shall be formatted with bold text off.
Normal priority, wait for user to clear
message.
Message shall be formatted with bold text on.
Normal priority, wait for user to clear
message.
Message shall be formatted with bold text off.
Release 10
105
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 8.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
10
8D
69
B4
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
PROACTIVE COMMAND: DISPLAY TEXT 8.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
ETSI
Release 10
106
Text String
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"Text Attribute 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
00
8D
69
B4
02
72
8D
69
PROACTIVE COMMAND: DISPLAY TEXT 8.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 3"
Coding:
BER-TLV:
27.22.4.1.8.6.5
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
33
80
20
82
41
02
74
81
74
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.6.
27.22.4.1.8.7
DISPLAY TEXT (Support of Text Attribute - Italic On)
27.22.4.1.8.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.7.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with italic on for the display text.
27.22.4.1.8.7.3
Test purpose
To verify that the Terminal displays the text formatted according to the italic text attribute configuration contained in
the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL RESPONSE
command send to the UICC.
ETSI
Release 10
107
27.22.4.1.8.7.4
Method of test
27.22.4.1.8.7.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.8.7.4.2
Procedure
Expected Sequence 8.7 (DISPLAY TEXT, Text Attribute with Italic On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.7.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.7.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.7.2
Terminal → USER Display "Text Attribute 2"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.7.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.7.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.7.3
Terminal → USER Display "Text Attribute 3"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.7.1
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with italic on.
Normal priority, wait for user to clear
message.
Message shall be formatted with italic off.
Normal priority, wait for user to clear
message.
Message shall be formatted with italic on.
Normal priority, wait for user to clear
message.
Message shall be formatted with italic off.
PROACTIVE COMMAND: DISPLAY TEXT 8.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
ETSI
Release 10
108
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
20
8D
69
B4
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
PROACTIVE COMMAND: DISPLAY TEXT 8.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
ETSI
Release 10
109
Colour:
ETSI TS 102 384 V10.3.0 (2015-08)
Dark Green Foreground, Bright Yellow Background
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
00
8D
69
B4
02
72
8D
69
PROACTIVE COMMAND: DISPLAY TEXT 8.7.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 3"
Coding:
BER-TLV:
27.22.4.1.8.7.5
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
33
80
20
82
41
02
74
81
74
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.7.
27.22.4.1.8.8
DISPLAY TEXT (Support of Text Attribute - Underline On)
27.22.4.1.8.8.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.8.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with underline on for the display text.
27.22.4.1.8.8.3
Test purpose
To verify that the Terminal displays the text formatted according to the underline text attribute configuration contained
in the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL RESPONSE
command send to the UICC.
27.22.4.1.8.8.4
Method of test
27.22.4.1.8.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
110
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.8.8.4.2
Procedure
Expected Sequence 8.8 (DISPLAY TEXT, Text Attribute with Underline On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.8.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.8.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.8.2
Terminal → USER Display "Text Attribute 2"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.8.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.8.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.8.3
Terminal → USER Display "Text Attribute 3"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.8.1
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with underline on.
Normal priority, wait for user to clear
message.
Message shall be formatted with underline off.
Normal priority, wait for user to clear
message.
Message shall be formatted with underline on.
Normal priority, wait for user to clear
message.
Message shall be formatted with underline off.
PROACTIVE COMMAND: DISPLAY TEXT 8.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
ETSI
Release 10
111
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
40
8D
69
B4
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
PROACTIVE COMMAND: DISPLAY TEXT 8.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
32
ETSI
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
00
8D
69
B4
Release 10
112
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 8.8.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 3"
Coding:
BER-TLV:
27.22.4.1.8.8.5
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
33
80
20
82
41
02
74
81
74
02
72
8D
69
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.8.
27.22.4.1.8.9
DISPLAY TEXT (Support of Text Attribute - Strikethrough On)
27.22.4.1.8.9.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.9.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with underline on for the display text.
27.22.4.1.8.9.3
Test purpose
To verify that the Terminal displays the text formatted according to the strikethrough text attribute configuration
contained in the DISPLAY TEXT proactive UICC command, and returns a successful result in the TERMINAL
RESPONSE command send to the UICC.
27.22.4.1.8.9.4
Method of test
27.22.4.1.8.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
113
27.22.4.1.8.9.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 8.9 (DISPLAY TEXT, Text Attribute with Strikethrough On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
21
22
23
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.9.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.9.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.9.3
Terminal → USER Display "Text Attribute 2"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.9.1
Terminal → USER Display "Text Attribute 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.9.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.9.3
Terminal → USER Display "Text Attribute 3"
Comments
Normal priority, wait for user to clear
message.
Message shall be formatted with strikethrough
on.
Normal priority, wait for user to clear
message.
Message shall be formatted with strikethrough
off.
Normal priority, wait for user to clear
message.
Message shall be formatted with strikethrough
on.
Normal priority, wait for user to clear
message.
Message shall be formatted with strikethrough
off.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.9.1
PROACTIVE COMMAND: DISPLAY TEXT 8.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
ETSI
Release 10
114
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
80
8D
69
B4
01
00
TERMINAL RESPONSE: DISPLAY TEXT 8.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
PROACTIVE COMMAND: DISPLAY TEXT 8.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
32
ETSI
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
00
8D
69
B4
Release 10
115
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 8.9.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 3"
Coding:
BER-TLV:
27.22.4.1.8.9.5
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
33
80
20
82
41
02
74
81
74
02
72
8D
69
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.9.
27.22.4.1.8.10
DISPLAY TEXT (Support of Text Attribute - Foreground and Background Colours)
27.22.4.1.8.10.1
Definition and applicability
See clause 3.2.2.
27.22.4.1.8.10.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.31, 8.43 and 8.70.
The Terminal shall support the text attribute with different foreground and background colours for the display text.
27.22.4.1.8.10.3
Test purpose
To verify that the Terminal displays the text formatted according to the foreground and background colour text attribute
configuration contained in the DISPLAY TEXT proactive UICC command, and returns a successful result in the
TERMINAL RESPONSE command send to the UICC.
27.22.4.1.8.10.4
Method of test
27.22.4.1.8.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
116
27.22.4.1.8.10.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 8.10 (DISPLAY TEXT, Text Attribute with Foreground and Background Colours)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.10.1
Terminal → UICC FETCH
Normal priority, wait for user to clear
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.10.1
message.
Message shall be formatted with foreground
Terminal → USER Display "Text Attribute 1"
and background colour according to text
attribute configuration.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.10.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 8.10.2
Terminal → UICC FETCH
Normal priority, wait for user to clear
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 8.10.2
message.
Message shall be formatted with Terminal's
Terminal → USER Display "Text Attribute 2"
default foreground and background colour.
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 8.10.1
PROACTIVE COMMAND: DISPLAY TEXT 8.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
62
22
04
75
81
54
74
03
65
65
01
78
20
21
74
31
ETSI
80
20
D0
82
41
04
02
74
00
81
74
10
02
72
00
8D
69
B4
Release 10
117
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: DISPLAY TEXT 8.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
01
00
02
72
8D
69
PROACTIVE COMMAND: DISPLAY TEXT 8.10.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Text Attribute 2"
Coding:
BER-TLV:
27.22.4.1.8.10.5
D0
11
62
1C
04
75
81
54
74
03
65
65
01
78
20
21
74
32
80
20
82
41
02
74
81
74
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.10.
27.22.4.1.9
27.22.4.1.9.1
DISPLAY TEXT (UCS2 display in Chinese)
Definition and applicability
See clause 3.2.2.
27.22.4.1.9.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.31.
The Terminal shall support the UCS2 alphabet for the coding of the Chinese character, as defined in the following
technical specification: ISO/IEC 10646 [2].
ETSI
Release 10
118
27.22.4.1.9.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text contained in the DISPLAY TEXT proactive UICC command, and returns a
successful result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.9.4
Method of test
27.22.4.1.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.9.4.2
Procedure
Expected Sequence 9.1 (DISPLAY TEXT, UCS2 coded in Chinese)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 9.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 9.1.1
Terminal → USER Display "
"
你好
Comments
Normal priority, wait for user to clear
message, UCS2 coded.
"Hello" in Chinese.
USER → Terminal Clear message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 9.1.1
PROACTIVE COMMAND: DISPLAY TEXT 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
UCS2 (16bit)
Text:
"
你好"
Coding:
BER-TLV:
D0
05
10
08
81
4F
03
60
01
59
21
7D
80
82
02
81
TERMINAL RESPONSE: DISPLAY TEXT 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
ETSI
02
8D
Release 10
119
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.1.9.5
81
03
01
21
80
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.1.
27.22.4.1.10
27.22.4.1.10.1
DISPLAY TEXT (UCS2 display in Katakana)
Definition and applicability
See clause 3.2.2.
27.22.4.1.10.2
Conformance requirement
The Terminal shall support the DISPLAY TEXT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.1, 6.5.4, 6.6.1, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.31.
The Terminal shall support the UCS2 alphabet for the coding of the Katakana character, as defined in the following
technical specification: ISO/IEC 10646 [2].
27.22.4.1.10.3
Test purpose
To verify that the Terminal displays the text contained in the DISPLAY TEXT proactive UICC command, and returns a
successful result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.1.10.4
Method of test
27.22.4.1.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.1.10.4.2
Procedure
Expected Sequence 10.1 (DISPLAY TEXT, UCS2 coded in Katakana)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 10.1.1
Terminal → UICC FETCH
Normal priority, wait for user to clear
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 10.1.1
message, UCS2 coded.
Characters in Katakana.
Terminal → USER Display "80 "
ル
USER → Terminal Clear message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 10.1.1
ETSI
Release 10
120
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
UCS2 (16bit)
"80 "
ル
Coding:
BER-TLV:
D0
07
12
08
81
00
03
38
01
00
21
30
80
30
82
EB
02
81
02
8D
01
00
TERMINAL RESPONSE: DISPLAY TEXT 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.1.10.5
81
03
01
21
80
82
02
82
81
83
Test requirement
The Terminal shall operate in the manner defined in expected sequence 10.1.
27.22.4.2
27.22.4.2.1
27.22.4.2.1.1
GET INKEY
GET INKEY(normal)
Definition and applicability
See clause 3.2.2.
27.22.4.2.1.2
Conformance Requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
27.22.4.2.1.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
single character entered in the TERMINAL RESPONSE command sent to the UICC.
ETSI
Release 10
121
27.22.4.2.1.4
Method of test
27.22.4.2.1.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be set to a display other than the idle display.
27.22.4.2.1.4.2
Procedure
Expected Sequence 1.1 (GET INKEY, digits only for character, Unpacked 8 bit data for Text String, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 1.1.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 1.1.1
Comments
Digits only, no help info available.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
02
22
81
2B
82
22
8D
TERMINAL RESPONSE: GET INKEY 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
122
Text String
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 1.2 (GET INKEY, digits only for character set, SMS default Alphabet for Text String,
successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 1.2.1
Terminal → USER Display "Enter "0""
USER → Terminal Enter the input "0" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 1.2.1
Comments
Digits only, no help info available.
Text string coding in packed format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
SMS default alphabet
"Enter "0""
Coding:
BER-TLV:
D0
09
14
00
81
45
03
37
01
BD
22
2C
00
07
82
89
02
60
81
22
82
8D
TERMINAL RESPONSE: GET INKEY 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
123
Text String
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"0"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
30
00
82
02
82
81
83
01
00
Expected Sequence 1.3 (GET INKEY, backward move)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 1.3.1
Terminal → USER Display "<GO-BACKWARDS>"
USER → Terminal Backwards move MMI action
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 1.3.1
Comments
Digits only, no help information available.
Text string coding in unpacked format.
Backward move in the proactive UICC
session requested by the user.
PROACTIVE COMMAND: GET INKEY 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<GO-BACKWARDS>"
Coding:
BER-TLV:
D0
0F
52
1A
04
44
81
3C
53
03
47
3E
01
4F
22
2D
00
42
82
41
02
43
81
4B
82
57
8D
41
TERMINAL RESPONSE: GET INKEY 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
backward move in the proactive UICC session requested by the user
ETSI
Release 10
124
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
03
01
22
00
82
02
82
81
83
01
11
Expected Sequence 1.4 (GET INKEY, abort)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 1.4.1
Terminal → USER Display "<ABORT>"
USER → Terminal Terminate the Proactive UICC
session MMI action
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 1.4.1
Comments
Digits only, no help information available.
Text string coding in unpacked format.
Proactive UICC session terminated by the
user.
PROACTIVE COMMAND: GET INKEY 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<ABORT>"
Coding:
BER-TLV:
D0
08
13
04
81
3C
03
41
01
42
22
4F
00
52
82
54
02
3E
81
82
8D
TERMINAL RESPONSE: GET INKEY 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Proactive UICC session terminated by the user
Coding:
BER-TLV:
81
03
01
22
00
82
ETSI
02
82
81
83
01
10
Release 10
125
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.5 (GET INKEY, SMS default alphabet for character set, Unpacked 8 bit data for Text
String, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 1.5.1
Terminal → USER Display "Enter "q""
USER → Terminal Enter the input "q" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 1.5.1
Comments
Characters from SMS default alphabet, no
help info available.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
SMS default alphabet, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "q""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
01
72
82
20
02
22
81
71
82
22
8D
TERMINAL RESPONSE: GET INKEY 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
SMS default alphabet, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"q"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
71
01
82
ETSI
02
82
81
83
01
00
Release 10
126
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.6 (GET INKEY, Max length for the Text String, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 1.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 1.6.1
Terminal → USER Display "Enter "x". This
command instructs the ME to
display text, and to expect the
user to enter a single character.
Any response entered by the
user shall be passed t"
USER → Terminal Enter the input "x" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 1.6.1
Comments
Digits only, no help info available.
160 characters Text string coding in unpacked
format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
SMS default alphabet, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
unpacked, 8 bit data
Text:
"Enter "x". This command instructs the ME to display text, and
expect the user to enter a single character. Any response entered by the user shall be passed t"
Coding:
BER-TLV:
D0
8D
22
61
73
64
2C
65
20
73
63
73
65
65
70
81
81
2E
6E
20
69
20
63
74
69
74
70
64
72
61
AD
A1
20
64
74
73
61
74
6F
6E
65
6F
20
20
73
81
04
54
20
68
70
6E
20
20
67
72
6E
62
73
73
03
45
68
69
65
6C
64
74
65
6C
2E
73
79
68
65
01
6E
69
6E
20
61
20
68
6E
65
20
65
20
61
64
22
74
73
73
4D
79
74
65
74
20
41
20
74
6C
20
01
65
20
74
45
20
6F
20
65
63
6E
65
68
6C
74
82
72
63
72
20
74
20
75
72
68
79
6E
65
20
02
20
6F
75
74
65
65
73
20
61
20
74
20
62
81
22
6D
63
6F
78
78
65
61
72
72
65
75
65
TERMINAL RESPONSE: GET INKEY 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
SMS default alphabet, no help information available
ETSI
82
78
6D
74
20
74
70
72
20
61
65
72
73
20
to
Release 10
127
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"x"
Coding:
BER-TLV:
27.22.4.2.1.5
81
8D
03
02
01
04
22
78
01
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.6.
27.22.4.2.2
GET INKEY (No response from User)
27.22.4.2.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.2.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
27.22.4.2.2.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns a "No
response from user" result value in the TERMINAL RESPONSE command send to the UICC.
27.22.4.2.2.4
Method of test
27.22.4.2.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
Terminal Manufacturers shall set the "no response from user" period of time as declared in table A.2/2.
The UICC Simulator shall be set to that period of time.
27.22.4.2.2.4.2
Procedure
Expected Sequence 2.1 (GET INKEY, no response from the user)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 2.1.1
Terminal → USER Display "<TIME-OUT>"
USER
Waiting and no completion
ETSI
Comments
Digits only, no help information available.
Text string coding in unpacked format.
Release 10
Step
6
7
128
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
No response from user within 5 s after the end
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 2.1.1
of that defined period of time.
USER
Check the delay of TERMINAL
RESPONSE is reasonable or not
PROACTIVE COMMAND: GET INKEY 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<TIME-OUT>"
Coding:
BER-TLV:
D0
0B
16
04
81
3C
03
54
01
49
22
4D
00
45
82
2D
02
4F
81
55
82
54
8D
3E
TERMINAL RESPONSE: GET INKEY 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
No response from user
Coding:
BER-TLV:
27.22.4.2.2.5
81
03
01
22
00
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.2.3
27.22.4.2.3.1
GET INKEY (UCS2 display in Cyrillic)
Definition and applicability
See clause 3.2.2.
ETSI
82
81
83
01
12
Release 10
129
27.22.4.2.3.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally, the Terminal shall support the UCS2 facility for the coding of the Cyrillic alphabet, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.2.3.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.3.4
Method of test
27.22.4.2.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.3.4.2
Procedure
Expected Sequence 3.1 (GET INKEY, Text String coding in UCS2 Alphabet in Cyrillic, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 3.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 3.1.1
Terminal → USER Display " ЗДРАВСТВУЙТЕ "
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 3.1.1
Comments
Digits only, no help information available.
Text string "Hello" in Russian coding in 16 bits
UCS2 alphabet format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
" ЗДРАВСТВУЙТЕ "
Coding:
BER-TLV:
D0
19
04
04
24
08
21
15
81
04
04
03
17
22
01
04
04
22
14
12
ETSI
00
04
04
82
20
23
02
04
04
81
10
19
82
04
04
8D
12
22
Release 10
130
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INKEY 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 3.2 (GET INKEY, max length for the Text String coding in UCS2 Alphabet in Cyrillic,
successful)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 3.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 3.2.1
Terminal → USER Display
"ЗДРАВСТВУЙТЕЗДРАВСТВУ
ЙТЕЗДРАВСТВУЙТЕЗДРАВСТ
ВУЙТЕЗДРАВСТВУЙТЕЗДРАВ
СТВУЙ"
5
6
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 3.2.1
Comments
Digits only, no help information available.
Text string length 70 characters, coding in 16
bits UCS2 alphabet format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 3.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
"ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙ"
ETSI
Release 10
131
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
8D
04
04
04
04
04
04
04
04
04
04
04
81
81
12
22
12
22
12
22
12
22
12
22
12
99
8D
04
04
04
04
04
04
04
04
04
04
04
81
08
21
15
21
15
21
15
21
15
21
15
21
03
04
04
04
04
04
04
04
04
04
04
04
04
01
17
22
17
22
17
22
17
22
17
22
17
22
22
04
04
04
04
04
04
04
04
04
04
04
04
00
14
12
14
12
14
12
14
12
14
12
14
12
82
04
04
04
04
04
04
04
04
04
04
04
04
02
20
23
20
23
20
23
20
23
20
23
20
23
81
04
04
04
04
04
04
04
04
04
04
04
04
82
10
19
10
19
10
19
10
19
10
19
10
19
TERMINAL RESPONSE: GET INKEY 3.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
27.22.4.2.3.5
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 3.1 to 3.2.
27.22.4.2.4
27.22.4.2.4.1
GET INKEY (UCS2 entry in Cyrillic)
Definition and applicability
See clause 3.2.2.
27.22.4.2.4.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally, the Terminal shall support the UCS2 facility for the coding of the Cyrillic alphabet, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.2.4.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
ETSI
Release 10
132
27.22.4.2.4.4
Method of test
27.22.4.2.4.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.4.4.2
Procedure
Expected Sequence 4.1 (GET INKEY, characters from UCS2 alphabet in Cyrillic, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 4.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 4.1.1
Terminal → USER Display "Enter"
USER → Terminal Enter the input "Д"
and completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 4.1.1
Comments
Characters from UCS2 alphabet, no help
information available.
Text string coding in unpacked format.
Cyrillic character, coding in UCS2 format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
characters from UCS2 alphabet, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter"
Coding:
BER-TLV:
D0
06
11
04
81
45
03
6E
01
74
22
65
03
72
82
02
81
82
8D
TERMINAL RESPONSE: GET INKEY 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
characters from UCS2 alphabet, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
133
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
16 bit data UCS2 alphabet format
"Д"
Coding:
BER-TLV:
27.22.4.2.4.5
81
8D
03
03
01
08
22
04
03
14
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.1.
27.22.4.2.5
GET INKEY ("Yes/No" Response)
27.22.4.2.5.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.5.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
27.22.4.2.5.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.5.4
Method of test
27.22.4.2.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.5.4.2
Procedure
Expected Sequence 5.1 (GET INKEY, "Yes/No" Response for the input, successful)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 5.1.1
Terminal → USER Display "Enter YES "
5
6
USER → Terminal Choice "Yes" and Completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 5.1.1
7
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 5.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 5.1.2
8
9
ETSI
Comments
"Yes/No" Response, no help information
available.
Text string coding in unpacked format.
Command performed successfully.
Check if it is in accordance with the user
choice (value '01' in the Text String data
object).
"Yes/No" Response, no help information
available.
Release 10
Step
10
11
12
134
Direction
Message/Action
Terminal → USER Display "Enter NO:"
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Text string coding in unpacked format.
USER → Terminal Choice "No" and Completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 5.1.2
Command performed successfully.
Check if it is in accordance with the user
choice (value '00' in the Text String data
object).
PROACTIVE COMMAND: GET INKEY 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
"Yes/No" Response, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter YES"
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
04
72
82
20
02
59
81
45
82
53
8D
TERMINAL RESPONSE: GET INKEY 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
"Yes/No" Response, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
01 (hex)
Coding:
BER-TLV:
81
8D
03
02
01
04
22
01
04
82
PROACTIVE COMMAND: GET INKEY 5.1.2
Logically:
Command details
Command number:
Command type:
1
GET INKEY
ETSI
02
82
81
83
01
00
Release 10
135
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
"Yes/No" Response, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter NO"
Coding:
BER-TLV:
D0
09
14
04
81
45
03
6E
01
74
22
65
04
72
82
20
02
4E
81
4F
82
8D
TERMINAL RESPONSE: GET INKEY 5.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
"Yes/No" Response, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
00 (hex)
Coding:
BER-TLV:
27.22.4.2.5.5
81
8D
03
02
01
04
22
00
04
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 5.1.
27.22.4.2.6
GET INKEY (display of Icon)
27.22.4.2.6.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.6.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.31.
27.22.4.2.6.3
Test purpose
To verify that the Terminal displays the Icon contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
ETSI
Release 10
136
27.22.4.2.6.4
Method of test
27.22.4.2.6.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.6.4.2
Procedure
Expected Sequence 6.1A (GET INKEY, Basic icon, self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.1.1
Terminal → USER Display the BASIC-ICON for the
prompt
USER → Terminal Enter "+" and completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.1.1A
Comments
BASIC-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<NO-ICON>"
Icon Identifier
Icon qualifier:
Icon identifier:
self-explanatory
1 (number of record in EFImg)
Coding:
BER-TLV:
D0
0A
02
19
04
00
81
3C
01
03
4E
01
4F
22
2D
00
49
82
43
02
4F
81
4E
82
3E
8D
1E
TERMINAL RESPONSE: GET INKEY 6.1.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
ETSI
Release 10
137
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.1B (GET INKEY, Basic icon, self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.1.1
Terminal → USER Display "<NO-ICON>" for the
prompt without the icon
USER → Terminal Enter "+" and completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.1.1B
Comments
BASIC-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INKEY 6.1.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
displayed
Command performed successfully but requested icon could not be
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
ETSI
02
82
81
83
01
04
Release 10
138
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 6.2A (GET INKEY, Basic icon, non self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.2.1
Terminal → USER Display "<BASIC-ICON>" and
Display the BASIC-ICON for the
prompt
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.2.1A
Comments
BASIC-ICON non self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 6.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<BASIC-ICON>"
Icon Identifier
Icon qualifier:
Icon identifier:
not self-explanatory
1 (number of record in EFImg)
Coding:
BER-TLV:
D0
0D
4E
1C
04
3E
81
3C
1E
03
42
02
01
41
01
22
53
01
00
49
82
43
02
2D
81
49
82
43
8D
4F
TERMINAL RESPONSE: GET INKEY 6.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Text string
Data coding scheme:
Text:
Command performed successfully
unpacked, 8 bit data
"+"
ETSI
Release 10
139
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.2B (GET INKEY, Basic icon, non self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.2.1
Terminal → USER Display "<BASIC-ICON>" for the
prompt without the icon
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.2.1B
Comments
BASIC-ICON non self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INKEY 6.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
04
Expected Sequence 6.3A (GET INKEY, Colour icon, self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.3.1
Terminal → USER Display the COLOUR-ICON for
the prompt
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.3.1A
ETSI
Comments
COLOUR-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully.
Release 10
140
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INKEY 6.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<NO-ICON>"
Icon Identifier
Icon qualifier:
Icon identifier:
self-explanatory
2 (number of record in EFImg)
Coding:
BER-TLV:
D0
0A
02
19
04
00
81
3C
02
03
4E
01
4F
22
2D
00
49
82
43
02
4F
81
4E
82
3E
8D
1E
TERMINAL RESPONSE: GET INKEY 6.3.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.3B (GET INKEY, Colour icon, self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.3.1
Terminal → USER Display "<NO-ICON>"for the
prompt without the icon
USER → Terminal Enter the input "+" and
completion
ETSI
Comments
COLOUR-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Release 10
Step
6
141
Direction
Message/Action
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.3.1B
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INKEY 6.3.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
04
Expected Sequence 6.4A (GET INKEY, Colour icon, non self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.4.1
Terminal → USER Display "<COLOUR-ICON>" and
Display the COLOUR-ICON for
the prompt
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.4.1A
Comments
COLOUR-ICON non self-explanatory for the
Text string.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 6.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<COLOUR-ICON>"
ETSI
Release 10
142
Icon Identifier
Icon qualifier:
Icon identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
not self-explanatory
2 (number of record in EFImg)
Coding:
BER-TLV:
D0
0E
4F
1D
04
4E
81
3C
3E
03
43
1E
01
4F
02
22
4C
01
00
4F
02
82
55
02
52
81
2D
82
49
8D
43
TERMINAL RESPONSE: GET INKEY 6.4.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.4B (GET INKEY, Colour icon, non self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 6.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 6.4.1
Terminal → USER Display "<COLOUR-ICON>" for
the prompt without the icon
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 6.4.1B
Comments
COLOUR-ICON non self-explanatory for the
Text string.
Text string coding in unpacked format.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INKEY 6.4.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
143
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
27.22.4.2.6.5
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
04
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.1A to 6.4B.
27.22.4.2.7
GET INKEY (Help Information)
27.22.4.2.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.7.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.31.
27.22.4.2.7.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.7.4
Method of test
27.22.4.2.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.7.4.2
Procedure
Expected Sequence 7.1 (GET INKEY, help information available)
Step
1
2
3
4
5
6
7
8
9
10
11
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 7.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 7.1.1
Terminal → USER Display "Enter "+""
USER → Terminal Press "help" key
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 7.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 7.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 7.1.1
Terminal → USER Display 'Help information'
USER → Terminal Clear Message
ETSI
Comments
Digits only, help information available.
Text string coding in unpacked format.
Help info required.
Text string coded in unpacked format.
Release 10
Step
12
13
14
15
144
Direction
Message/Action
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 7.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 7.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 7.1.2
16
Terminal → USER Display "Enter "+""
17
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 7.1.2
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Digits only, help information available.
Repetition of get inkey.
18
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
80
72
82
20
02
22
81
2B
82
22
8D
TERMINAL RESPONSE: GET INKEY 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Help information required by the user
Coding:
BER-TLV:
81
03
01
22
80
82
ETSI
02
82
81
83
01
13
Release 10
145
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: DISPLAY TEXT 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Help information"
Coding:
BER-TLV:
D0
11
6D
1C
04
61
81
48
74
03
65
69
01
6C
6F
21
70
6E
80
20
82
69
02
6E
81
66
02
6F
8D
72
01
00
TERMINAL RESPONSE: DISPLAY TEXT 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
02
82
81
83
PROACTIVE COMMAND: GET INKEY 7.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
ETSI
80
72
82
20
02
22
81
2B
82
22
8D
Release 10
146
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INKEY 7.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
27.22.4.2.7.5
81
8D
03
02
01
04
22
2B
80
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 7.1.
27.22.4.2.8
27.22.4.2.8.1
GET INKEY (Variable Time out)
Definition and applicability
See clause 3.2.2.
27.22.4.2.8.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3 and
8.31.
27.22.4.2.8.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.8.4
Method of test
27.22.4.2.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
147
27.22.4.2.8.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 8.1 (GET INKEY, variable time out of 10 seconds)
Step
1
2
3
4
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 8.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 8.1.1
Terminal → USER Display "Enter "+"" for 10
seconds
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 8.1.1
Comments
Text string coding in unpacked format.
No response from user.
PROACTIVE COMMAND: GET INKEY 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Duration
Time unit:
Time interval:
Seconds
10
Coding:
BER-TLV:
D0
0A
02
19
04
01
81
45
0A
03
6E
01
74
22
65
00
72
82
20
02
22
TERMINAL RESPONSE: GET INKEY 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Duration
Time unit:
Time interval:
No response from user
seconds
any value greater than or equal to 10
ETSI
81
2B
82
22
8D
84
Release 10
148
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
04
03
02
01
01
22
Cond
001
00
82
02
82
81
83
01
12
Cond001: Coding of any value greater than or equal to 10.
27.22.4.2.8.5
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.1.
27.22.4.2.9
GET INKEY (Support of Text Attribute)
27.22.4.2.9.1
GET INKEY (Support of Text Attribute - Left Alignment)
27.22.4.2.9.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.9.1.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.1.3
Test purpose
To verify that the Terminal displays the text formatted according to the left alignment text attribute configuration
contained in the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.2.9.1.4
Method of test
27.22.4.2.9.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.9.1.4.2
Procedure
Expected Sequence 9.1 (GET INKEY, Text attribute with Left Alignment )
Step
1
2
3
4
5
6
7
8
9
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.1.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.1.2
ETSI
Comments
Message shall be formatted with left
alignment.
Command performed successfully.
Release 10
Step
10
11
12
149
Direction
Message/Action
Terminal → USER Display "Enter "#""
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Message shall be formatted without left
alignment. Remark: If left alignment is the
Terminal's default alignment as declared in
table A.2/6, no alignment change will take
place.
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.1.2
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
00
72
82
20
02
22
TERMINAL RESPONSE: GET INKEY 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Text String
Data coding scheme:
Text:
Command performed successfully
unpacked, 8 bit data
"+"
ETSI
81
2B
82
22
8D
D0
Release 10
150
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
02
22
81
23
82
22
8D
83
01
00
PROACTIVE COMMAND: GET INKEY 9.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
TERMINAL RESPONSE: GET INKEY 9.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
27.22.4.2.9.1.5
81
8D
03
02
01
04
22
23
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.1.
27.22.4.2.9.2
GET INKEY (Support of Text Attribute - Center Alignment)
27.22.4.2.9.2.1
Definition and applicability
See clause 3.2.2.
ETSI
Release 10
151
27.22.4.2.9.2.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.2.3
Test purpose
To verify that the Terminal displays the text formatted according to the center alignment text attribute configuration
contained in the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.2.9.2.4
Method of test
27.22.4.2.9.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.9.2.4.2
Procedure
Expected Sequence 9.2 (GET INKEY, Text attribute with Center Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.2.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.2.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.2.2
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.2.2
Comments
Message shall be formatted with center
alignment.
Command performed successfully.
Message shall be formatted without center
alignment. Remark: If center alignment is the
Terminal's default alignment as declared in
table A.2/6, no alignment change will take
place.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
ETSI
Release 10
152
Text String
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Center Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
01
01
74
B4
22
65
00
72
82
20
02
22
81
2B
82
22
8D
D0
81
83
01
00
02
22
81
23
82
22
8D
TERMINAL RESPONSE: GET INKEY 9.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
PROACTIVE COMMAND: GET INKEY 9.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
ETSI
00
72
82
20
Release 10
153
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INKEY 9.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
27.22.4.2.9.2.5
81
8D
03
02
01
04
22
23
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.2.
27.22.4.2.9.3
GET INKEY (Support of Text Attribute - Right Alignment)
27.22.4.2.9.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.9.3.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.3.3
Test purpose
To verify that the Terminal displays the text formatted according to the right alignment text attribute configuration
contained in the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.2.9.3.4
Method of test
27.22.4.2.9.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
154
27.22.4.2.9.3.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 9.3 (GET INKEY, Text attribute with Right Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.3.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.3.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.3.2
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.3.2
Comments
Message shall be formatted with right
alignment.
Command performed successfully.
Message shall be formatted without right
alignment. Remark: If right alignment is the
Terminal's default alignment as declared in
table A.2/6, no alignment change will take
place.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
02
01
74
B4
22
65
ETSI
00
72
82
20
02
22
81
2B
82
22
8D
D0
Release 10
155
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INKEY 9.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
02
22
81
23
82
22
8D
PROACTIVE COMMAND: GET INKEY 9.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
TERMINAL RESPONSE: GET INKEY 9.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
156
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"#"
Coding
BER-TLV:
27.22.4.2.9.3.5
81
8D
03
02
01
04
22
23
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.3.
27.22.4.2.9.4
GET INKEY (Support of Text Attribute - Large Font Size)
27.22.4.2.9.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.9.4.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.4.3
Test purpose
To verify that the Terminal displays the text formatted according to the large font size text attribute configuration
contained in the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.2.9.4.4
Method of test
27.22.4.2.9.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.9.4.4.2
Procedure
Expected Sequence 9.4 (GET INKEY, Text attribute with Large Font Size)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.4.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.4.2
Terminal → USER Display "Enter "#""
ETSI
Comments
Message shall be formatted with large font
size.
Command performed successfully.
Message shall be formatted with normal font
size.
Release 10
Step
11
12
13
14
15
16
17
18
19
20
21
22
23
24
157
Direction
Message/Action
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.4.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.4.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.4.3
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command performed successfully.
Message shall be formatted with large font
size.
Command performed successfully.
Message shall be formatted with normal font
size.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
04
01
74
B4
22
65
TERMINAL RESPONSE: GET INKEY 9.4.1
Logically:
Command details
Command number:
1
ETSI
00
72
82
20
02
22
81
2B
82
22
8D
D0
Release 10
158
Command type:
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
PROACTIVE COMMAND: GET INKEY 9.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
00
72
82
20
02
22
TERMINAL RESPONSE: GET INKEY 9.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
81
23
82
22
8D
D0
Release 10
159
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
23
00
82
02
82
81
83
01
00
02
22
81
23
82
22
8D
PROACTIVE COMMAND: GET INKEY 9.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
27.22.4.2.9.4.5
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.4.
27.22.4.2.9.5
GET INKEY (Support of Text Attribute - Small Font Size)
27.22.4.2.9.5.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.9.5.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.5.3
Test purpose
To verify that the Terminal displays the text formatted according to the small font size text attribute configuration
contained in the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.2.9.5.4
Method of test
27.22.4.2.9.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
160
27.22.4.2.9.5.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 9.5 (GET INKEY, Text attribute with Small Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.5.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.5.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.5.2
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.5.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.5.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.5.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.5.3
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.5.2
Comments
Message shall be formatted with small font
size.
Command performed successfully.
Message shall be formatted with normal font
size.
Command performed successfully.
Message shall be formatted with small font
size.
Command performed successfully.
Message shall be formatted with normal font
size.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
unpacked, 8 bit data
ETSI
Release 10
161
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
08
01
74
B4
22
65
00
72
82
20
02
22
81
2B
82
22
8D
D0
83
01
00
TERMINAL RESPONSE: GET INKEY 9.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
PROACTIVE COMMAND: GET INKEY 9.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Text colour:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
162
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
00
72
82
20
02
22
81
23
82
22
8D
D0
81
83
01
00
02
22
81
23
82
22
8D
TERMINAL RESPONSE: GET INKEY 9.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
23
00
82
02
82
PROACTIVE COMMAND: GET INKEY 9.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
27.22.4.2.9.5.5
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.5.
27.22.4.2.9.6
GET INKEY (Support of Text Attribute - Bold On)
27.22.4.2.9.6.1
Definition and applicability
See clause 3.2.2.
ETSI
Release 10
163
27.22.4.2.9.6.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.6.3
Test purpose
To verify that the Terminal displays the text formatted according to the bold text attribute configuration contained in the
GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL RESPONSE command
sent to the UICC.
27.22.4.2.9.6.4
Method of test
27.22.4.2.9.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.9.6.4.2
Procedure
Expected Sequence 9.6 (GET INKEY, Text attribute with Bold On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.6.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.6.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.6.2
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.6.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.6.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.6.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.6.3
Terminal → USER Display "Enter "#""
ETSI
Comments
Message shall be formatted with bold on.
Command performed successfully.
Message shall be formatted with bold off.
Command performed successfully.
Message shall be formatted with bold on.
Command performed successfully.
Message shall be formatted with bold off.
Release 10
Step
23
24
164
Direction
Message/Action
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.6.2
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
10
01
74
B4
22
65
00
72
82
20
02
22
81
2B
82
22
8D
D0
83
01
00
TERMINAL RESPONSE: GET INKEY 9.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
ETSI
02
82
81
Release 10
165
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INKEY 9.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
00
72
82
20
02
22
81
23
82
22
8D
D0
83
01
00
TERMINAL RESPONSE: GET INKEY 9.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
23
00
82
02
82
PROACTIVE COMMAND: GET INKEY 9.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
ETSI
81
Release 10
166
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
27.22.4.2.9.6.5
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
02
22
81
23
82
22
8D
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.6.
27.22.4.2.9.7
GET INKEY (Support of Text Attribute - Italic On)
27.22.4.2.9.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.9.7.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.7.3
Test purpose
To verify that the Terminal displays the text formatted according to the italic text attribute configuration contained in
the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL RESPONSE
command sent to the UICC.
27.22.4.2.9.7.4
Method of test
27.22.4.2.9.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.9.7.4.2
Procedure
Expected Sequence 9.7 (GET INKEY, Text attribute with Italic On)
Step
1
2
3
4
5
6
7
8
9
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.7.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.7.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.7.2
ETSI
Comments
Message shall be formatted with italic on.
Command performed successfully.
Release 10
Step
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
167
Direction
Message/Action
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.7.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.7.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.7.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.7.3
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.7.2
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Message shall be formatted with italic off.
Command performed successfully.
Message shall be formatted with italic on.
Command performed successfully.
Message shall be formatted with italic off.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
20
01
74
B4
22
65
TERMINAL RESPONSE: GET INKEY 9.7.1
Logically:
Command details
Command number:
Command type:
1
GET INKEY
ETSI
00
72
82
20
02
22
81
2B
82
22
8D
D0
Release 10
168
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
PROACTIVE COMMAND: GET INKEY 9.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
00
72
82
20
02
22
TERMINAL RESPONSE: GET INKEY 9.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
81
23
82
22
8D
D0
Release 10
169
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
23
00
82
02
82
81
83
01
00
02
22
81
23
82
22
8D
PROACTIVE COMMAND: GET INKEY 9.7.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
27.22.4.2.9.7.5
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.7.
27.22.4.2.9.8
GET INKEY (Support of Text Attribute - Underline On)
27.22.4.2.9.8.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.9.8.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.8.3
Test purpose
To verify that the Terminal displays the text formatted according to the underline text attribute configuration contained
in the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL RESPONSE
command sent to the UICC.
27.22.4.2.9.8.4
Method of test
27.22.4.2.9.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
170
27.22.4.2.9.8.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 9.8 (GET INKEY, Text attribute with Underline On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.8.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.8.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.8.2
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.8.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.8.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.8.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.8.3
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.8.2
Comments
Message shall be formatted with underline on.
Command performed successfully.
Message shall be formatted with underline off.
Command performed successfully.
Message shall be formatted with underline on.
Command performed successfully.
Message shall be formatted with underline off.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
ETSI
Release 10
171
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
40
01
74
B4
22
65
00
72
82
20
02
22
81
2B
82
22
8D
D0
83
01
00
TERMINAL RESPONSE: GET INKEY 9.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
PROACTIVE COMMAND: GET INKEY 9.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Text colour:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
172
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
00
72
82
20
02
22
81
23
82
22
8D
D0
81
83
01
00
02
22
81
23
82
22
8D
TERMINAL RESPONSE: GET INKEY 9.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
23
00
82
02
82
PROACTIVE COMMAND: GET INKEY 9.8.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
27.22.4.2.9.8.5
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.8.
27.22.4.2.9.9
GET INKEY (Support of Text Attribute - Strikethrough On)
27.22.4.2.9.9.1
Definition and applicability
See clause 3.2.2.
ETSI
Release 10
173
27.22.4.2.9.9.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.9.3
Test purpose
To verify that the Terminal displays the text formatted according to the strikethrough text attribute configuration
contained in the GET INKEY proactive UICC command, and returns the text string entered in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.2.9.9.4
Method of test
27.22.4.2.9.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.9.9.4.2
Procedure
Expected Sequence 9.9 (GET INKEY, Text attribute with Strikethrough On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.9.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.9.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.9.2
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.9.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.9.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.9.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.9.3
ETSI
Comments
Message shall be formatted with strikethrough
on.
Command performed successfully.
Message shall be formatted with strikethrough
off.
Command performed successfully.
Message shall be formatted with strikethrough
on.
Command performed successfully.
Release 10
Step
22
23
24
174
Direction
Message/Action
Terminal → USER Display "Enter "#""
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Message shall be formatted with strikethrough
off.
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.9.2
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
80
01
74
B4
22
65
00
72
82
20
02
22
81
2B
82
22
8D
D0
83
01
00
TERMINAL RESPONSE: GET INKEY 9.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
ETSI
02
82
81
Release 10
175
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INKEY 9.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Text colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
00
72
82
20
02
22
81
23
82
22
8D
D0
83
01
00
TERMINAL RESPONSE: GET INKEY 9.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
23
00
82
02
82
PROACTIVE COMMAND: GET INKEY 9.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
ETSI
81
Release 10
176
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
02
22
81
23
82
22
8D
02
22
81
23
82
22
8D
PROACTIVE COMMAND: GET INKEY 9.9.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
27.22.4.2.9.9.5
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.9.
27.22.4.2.9.10
GET INKEY (Support of Text Attribute - Foreground and Background Colour)
27.22.4.2.9.10.1
Definition and applicability
See clause 3.2.2.
27.22.4.2.9.10.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.5.4, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.8, 8.15, 8.15.1, 8.15.2, 8.15.3, 8.31
and 8.70.
27.22.4.2.9.10.3
Test purpose
To verify that the Terminal displays the text formatted according to the foreground and background colour text attribute
configuration contained in the GET INKEY proactive UICC command, and returns the text string entered in the
TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.9.10.4
Method of test
27.22.4.2.9.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
ETSI
Release 10
177
ETSI TS 102 384 V10.3.0 (2015-08)
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.2.9.10.4.2
Procedure
Expected Sequence 9.10 (GET INKEY, Text attribute with Foreground and Background Colour)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.10.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.10.1
Terminal → USER Display "Enter "+""
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.10.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 9.10.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 9.10.2
Terminal → USER Display "Enter "#""
USER → Terminal Enter the input "#" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 9.10.2
Comments
Message shall be formatted with foreground
and background colour according to text
attribute configuration.
Command performed successfully.
Message shall be formatted with Terminal's
default foreground and background colour.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 9.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "+""
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
9
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0A
04
1B
04
00
81
45
09
03
6E
00
01
74
B4
22
65
ETSI
00
72
82
20
02
22
81
2B
82
22
8D
D0
Release 10
178
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INKEY 9.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
02
22
81
23
82
22
8D
PROACTIVE COMMAND: GET INKEY 9.10.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter "#""
Coding:
BER-TLV:
D0
0A
15
04
81
45
03
6E
01
74
22
65
00
72
82
20
TERMINAL RESPONSE: GET INKEY 9.10.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
179
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"#"
Coding:
BER-TLV:
27.22.4.2.9.10.5
81
8D
03
02
01
04
22
23
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.10.
27.22.4.2.10
27.22.4.2.10.1
GET INKEY (UCS2 display in Chinese)
Definition and applicability
See clause 3.2.2.
27.22.4.2.10.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally, the Terminal shall support the UCS2 facility for the coding of the Chinese character, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.2.10.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.10.4
Method of test
27.22.4.2.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.10.4.2
Procedure
Expected Sequence 10.1 (GET INKEY, Text String coding in UCS2 Alphabet in Chinese, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 10.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 10.1.1
Terminal → USER Display "
"
你好
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 10.1.1
ETSI
Comments
Digits only, no help information available.
Text string "Hello" in Chinese coding in 16 bits
UCS2 alphabet format.
Command performed successfully.
Release 10
180
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INKEY 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
16 bit data UCS2 alphabet format
Text:
"
你好"
Coding:
BER-TLV:
D0
05
10
08
81
4F
03
60
01
59
22
7D
00
82
02
81
82
8D
TERMINAL RESPONSE: GET INKEY 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 10.2 (GET INKEY, max length for the Text String coding in UCS2 Alphabet in Chinese,
successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 10.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 10.2.1
ETSI
Comments
Digits only, no help information available.
Release 10
Step
4
181
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Terminal → USER Display
Comments
string length 70 characters, coding in 16
你好你好你好你好你好你好你 Text
bits UCS2 alphabet format.
好你好你好你好你好你好你好
你好你好你好你好你好你好你
好你好你好你好你好你好你好
你好你好你好你好你好你好你
好你好你好"
"
5
6
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 10.2.1
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 10.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
你好你好你好你好你好你好你好你好你好你好你好你好你好你好你好你好你
好你好你好你好你好你好你好你好你好你好你好你好你好你好你好你好你好你
好你好"
"
Coding:
BER-TLV:
D0
8D
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
81
81
60
60
60
60
60
60
60
60
60
60
60
99
8D
59
59
59
59
59
59
59
59
59
59
59
81
08
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
03
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
01
60
60
60
60
60
60
60
60
60
60
60
60
22
59
59
59
59
59
59
59
59
59
59
59
59
00
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
82
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
02
60
60
60
60
60
60
60
60
60
60
60
60
81
59
59
59
59
59
59
59
59
59
59
59
59
82
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
TERMINAL RESPONSE: GET INKEY 10.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
ETSI
Release 10
182
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
27.22.4.2.10.5
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 10.1 to 10.2.
27.22.4.2.11
27.22.4.2.11.1
GET INKEY (UCS2 entry in Chinese)
Definition and applicability
See clause 3.2.2.
27.22.4.2.11.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally, the Terminal shall support the UCS2 facility for the coding of the Chinese character, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.2.11.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.11.4
Method of test
27.22.4.2.11.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.11.4.2
Procedure
Expected Sequence 11.1 (GET INKEY, characters from UCS2 alphabet in Chinese, successful)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 11.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 11.1.1
Terminal → USER Display "Enter"
USER → Terminal Enter the input " " and
completion
好
ETSI
Comments
Characters from UCS2 alphabet, no help
information available.
Text string coding in unpacked format.
Chinese character, coding in UCS2 format.
Release 10
Step
6
183
Direction
Message/Action
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 11.1.1
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 11.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
characters from UCS2 alphabet, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter"
Coding:
BER-TLV:
D0
06
11
04
81
45
03
6E
01
74
22
65
03
72
82
02
81
82
8D
TERMINAL RESPONSE: GET INKEY 11.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
characters from UCS2 alphabet, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
16 bit data UCS2 alphabet format
Text:
"
好"
Coding:
BER-TLV:
27.22.4.2.11.5
81
8D
03
03
01
08
22
59
03
7D
82
02
82
Test requirement
The Terminal shall operate in the manner defined in expected sequences 11.1.
27.22.4.2.12
27.22.4.2.12.1
GET INKEY (UCS2 display in Katakana)
Definition and applicability
See clause 3.2.2.
ETSI
81
83
01
00
Release 10
184
27.22.4.2.12.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally, the Terminal shall support the UCS2 facility for the coding of the Katakana character, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.2.12.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.2.12.4
Method of test
27.22.4.2.12.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.12.4.2
Procedure
Expected Sequence 12.1 (GET INKEY, Text String coding in UCS2 Alphabet in Katakana, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 12.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 12.1.1
Terminal → USER Display " "
ル
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 12.1.1
Comments
Digits only, no help information available.
Text string character in Katakana coding in 16
bits UCS2 alphabet format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 12.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
" "
ル
Coding:
BER-TLV:
D0
03
0E
08
81
30
03
EB
01
22
ETSI
00
82
02
81
82
8D
Release 10
185
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INKEY 12.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Expected Sequence 12.2 (GET INKEY, max length for the Text String coding in UCS2 Alphabet in Katakana,
successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 12.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 12.2.1
Terminal → USER Display
"
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル"
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 12.2.1
Comments
Digits only, no help information available.
Text string length 70 characters, coding in 16
bits UCS2 alphabet format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 12.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
"
ルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルル
ルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルルル"
ETSI
Release 10
186
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
8D
30
30
30
30
30
30
30
30
30
30
30
81
81
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
99
8D
30
30
30
30
30
30
30
30
30
30
30
81
08
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
03
30
30
30
30
30
30
30
30
30
30
30
30
01
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
22
30
30
30
30
30
30
30
30
30
30
30
30
00
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
82
30
30
30
30
30
30
30
30
30
30
30
30
02
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
81
30
30
30
30
30
30
30
30
30
30
30
30
82
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
TERMINAL RESPONSE: GET INKEY 12.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
27.22.4.2.12.5
81
8D
03
02
01
04
22
2B
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 12.1 to 12.2.
27.22.4.2.13
27.22.4.2.13.1
GET INKEY (UCS2 entry in Katakana)
Definition and applicability
See clause 3.2.2.
27.22.4.2.13.2
Conformance requirement
The Terminal shall support the GET INKEY command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.2, 6.6.2, 6.8, 6.11, 8.6, 8.7, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally, the Terminal shall support the UCS2 facility for the coding of the Katakana character, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.2.13.3
Test purpose
To verify that the Terminal displays the text contained in the GET INKEY proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
ETSI
Release 10
187
27.22.4.2.13.4
Method of test
27.22.4.2.13.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.2.13.4.2
Procedure
Expected Sequence 13.1 (GET INKEY, characters from UCS2 alphabet in Katakana, successful)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INKEY 13.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INKEY 13.1.1
Terminal → USER Display "Enter"
USER → Terminal Enter the input " "
ル
and completion
Terminal → UICC TERMINAL RESPONSE: GET
INKEY 13.1.1
6
Comments
Characters from UCS2 alphabet, no help
information available.
Text string coding in unpacked format.
Katakana character, coding in UCS2 format.
Command performed successfully.
PROACTIVE COMMAND: GET INKEY 13.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
characters from UCS2 alphabet, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter"
Coding:
BER-TLV:
D0
06
11
04
81
45
03
6E
01
74
22
65
03
72
82
02
81
82
8D
TERMINAL RESPONSE: GET INKEY 13.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INKEY
characters from UCS2 alphabet, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
188
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
" "
ル
Coding:
BER-TLV:
27.22.4.2.13.5
81
8D
03
03
01
08
22
30
03
EB
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 13.1.
27.22.4.3
GET INPUT
27.22.4.3.1
GET INPUT (normal)
27.22.4.3.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.1.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
27.22.4.3.1.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.1.4
Method of test
27.22.4.3.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.1.4.2
Procedure
Expected Sequence 1.1 (GET INPUT, digits only, SMS default alphabet, Terminal to echo text, Terminal
supporting 8 bit data Message)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.1.1
4
Terminal → USER Display "Enter 12345"
5
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.1.1
6
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help info
available.
Range of expected length is 5-5
Text string coding in unpacked format.
Command performed successfully.
Release 10
189
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INPUT 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0C
35
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
31
81
32
82
33
8D
34
TERMINAL RESPONSE: GET INPUT 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
ETSI
02
34
82
35
81
83
01
00
Release 10
190
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.2 (GET INPUT, digits only, SMS default alphabet, Terminal to echo text, packing SMS
Point-to-point required by Terminal)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.2.1
4
Terminal → USER Display "Enter 67*#+"
5
USER → Terminal Enter the input "67*#+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.2.1
6
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing required, no help
information available.
Range of expected length is 5-5
Text string coding in packed format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in packed
SMS format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
SMS default alphabet
"Enter 67*#+"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0B
91
1A
00
02
81
45
05
03
37
05
01
BD
23
2C
08
07
82
D9
02
6E
81
AA
82
D1
8D
0A
TERMINAL RESPONSE: GET INPUT 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in packed
SMS format, Terminal to echo text, no help information available
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
191
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
packed SMS format
"67*#+"
Coding:
BER-TLV:
81
8D
03
06
01
00
23
B6
08
9B
82
6A
02
B4
82
02
81
83
01
00
Expected Sequence 1.3 (GET INPUT, character set, SMS Default Alphabet, Terminal to echo text, Terminal
supporting 8 bit data Message)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.3.1
4
Terminal → USER Display "Enter AbCdE"
5
USER → Terminal Enter the input "AbCdE" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.3.1
6
Comments
Character set, SMS default alphabet,
Terminal to echo text, packing not required,
no help information available.
Range of expected length is 5-5
Text string coding in unpacked format.
The Terminal may echo the input.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
Character set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter AbCdE"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0C
45
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
01
72
82
20
02
41
81
62
82
43
8D
64
TERMINAL RESPONSE: GET INPUT 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
Character set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
ETSI
Release 10
192
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"AbCdE"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
41
01
62
82
43
02
64
82
45
81
83
01
00
Expected Sequence 1.4 (GET INPUT, digits only, SMS default alphabet, Terminal to hide text, Terminal
supporting 8 bit data Message)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.4.1
Terminal → USER Display
"Password 1<SEND>2345678"
USER → Terminal Enter the input "2345678" and
completion
6
Terminal → USER Input not revealed
7
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.4.1
Comments
Digits only, SMS default alphabet, Terminal to
hide text, packing not required, no help
information available.
Range of expected length is 4-8
Text string coding in unpacked format.
User's input not to be revealed at any time,
optionally indication of key entries such as by
displaying "*".
optionally indication of key entries such as by
displaying "*".
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to hide text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Password 1<SEND>2345678"
Response length
Minimum length:
Maximum length:
4
8
Coding:
BER-TLV:
D0
18
3C
38
27
04
53
91
81
50
45
02
03
61
4E
04
01
73
44
08
23
73
3E
ETSI
04
77
32
82
6F
33
02
72
34
81
64
35
82
20
36
8D
31
37
Release 10
193
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to hide text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"2345678"
Coding:
BER-TLV:
81
8D
03
08
01
04
23
32
04
33
82
34
02
35
82
36
81
37
83
38
01
00
Expected Sequence 1.5 (GET INPUT, digits only, SMS default alphabet, Terminal to echo text, Terminal
supporting 8 bit data Message)
Step
1
2
3
4
5
6
7
8
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET Digits only, SMS default alphabet, Terminal to
INPUT 1.5.1
echo text, packing not required, no help
information available.
Range of expected length is 1-20
Terminal → USER Display "Enter 1..9,0..9,0(1)"
Text string coding in unpacked format.
USER → Terminal Completion without input
Terminal → USER The Terminal MMI takes action
to manage the entry of correct
numbers of characters.
USER → Terminal Enter
"12345678901234567890" and
completion
Terminal → UICC TERMINAL RESPONSE: GET Command performed successfully.
INPUT 1.5.1
PROACTIVE COMMAND: GET INPUT 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
UICC
Terminal
ETSI
Release 10
194
ETSI TS 102 384 V10.3.0 (2015-08)
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 1..9,0..9,0(1)"
Response length
Minimum length:
Maximum length:
1
20
Coding:
BER-TLV:
D0
15
2C
01
24
04
30
14
81
45
2E
03
6E
2E
01
74
39
23
65
2C
00
72
30
82
20
28
02
31
31
81
2E
29
82
2E
91
8D
39
02
TERMINAL RESPONSE: GET INPUT 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345678901234567890"
Coding:
BER-TLV:
81
8D
30
03
15
31
01
04
32
23
31
33
00
32
34
82
33
35
02
34
36
82
35
37
81
36
38
83
37
39
01
38
30
00
39
Expected Sequence 1.6 (GET INPUT, backwards move)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.6.1
4
Terminal → USER Display "<GO-BACKWARDS>"
5
6
USER → Terminal Backwards move MMI action
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.6.1
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 0-8
Text string coding in unpacked format.
Backward move in the proactive UICC
session requested by the user.
Release 10
195
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INPUT 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"<GO-BACKWARDS>"
Response length
Minimum length:
Maximum length:
0
8
Coding:
BER-TLV:
D0
0F
52
1E
04
44
81
3C
53
03
47
3E
01
4F
91
23
2D
02
00
42
00
82
41
08
02
43
81
4B
82
57
8D
41
TERMINAL RESPONSE: GET INPUT 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
backward move in the proactive UICC session requested by the user
Coding:
BER-TLV:
81
03
01
23
00
82
02
82
81
83
01
11
Expected Sequence 1.7 (GET INPUT, abort)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.7.1
4
Terminal → USER Display "<ABORT>"
5
USER → Terminal Terminate the Proactive UICC
session MMI action
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.7.1
6
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range if expected length is 0-8
Text string coding in unpacked format.
Proactive UICC session terminated by the
user.
Release 10
196
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INPUT 1.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"<ABORT>"
Response length
Minimum length:
Maximum length:
0
8
Coding:
BER-TLV:
D0
08
08
17
04
81
3C
03
41
01
42
23
4F
00
52
82
54
02
3E
81
91
82
02
8D
00
TERMINAL RESPONSE: GET INPUT 1.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Proactive UICC session terminated by the user
Coding:
BER-TLV:
81
03
01
23
00
82
02
82
81
83
01
10
Expected Sequence 1.8 (GET INPUT, digits only, SMS default alphabet, Terminal to echo text, Terminal
supporting 8 bit data Message)
Step
1
2
3
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET Digits only, SMS default alphabet, Terminal to
INPUT 1.8.1
echo text, packing not required, no help
information available.
ETSI
Release 10
Step
4
5
6
197
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Range of length expected is 160-160
Terminal → USER Display
"***1111111111###***2222222 Text string coding in unpacked format.
222###***3333333333###***44
44444444###***5555555555##
#***6666666666###***7777777
777###***8888888888###***99
99999999###***0000000000##
#"
USER → Terminal Enter the input
"***1111111111###***2222222
222###***3333333333###***44
44444444###***5555555555##
#***6666666666###***7777777
777###***8888888888###***99
99999999###***0000000000##
#"
and completion
Terminal → UICC TERMINAL RESPONSE: GET Command performed successfully.
INPUT 1.8.1
PROACTIVE COMMAND: GET INPUT 1.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
Text string
Data coding scheme:
Text:
Response length
Minimum length:
Maximum length:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
UICC
Terminal
unpacked, 8 bit data
"***1111111111###***2222222222###***3333333333###***4444444444###***
5555555555###***6666666666###***7777777777###***8888888888###***9999
999999###***0000000000###"
160
160
Coding:
BER-TLV:
D0
8D
31
32
2A
33
34
35
2A
36
37
38
2A
39
30
81
81
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
B1
A1
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
81
04
31
32
33
23
34
35
36
23
37
38
39
23
30
03
2A
31
32
33
2A
34
35
36
2A
37
38
39
2A
30
01
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
ETSI
23
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
00
31
23
32
33
34
23
35
36
37
23
38
39
30
23
82
31
2A
32
33
34
2A
35
36
37
2A
38
39
30
91
02
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
02
81
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
A0
82
31
32
23
33
34
35
23
36
37
38
23
39
30
A0
Release 10
198
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 1.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"***1111111111###***2222222222###***
3333333333###***4444444444###
***5555555555###***6666666666###
***7777777777###***8888888888###
***9999999999###***0000000000###"
Coding:
BER-TLV:
81
8D
31
32
2A
33
34
35
2A
36
37
38
2A
39
30
03
81
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
01
A1
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
23
04
31
32
33
23
34
35
36
23
37
38
39
23
30
00
2A
31
32
33
2A
34
35
36
2A
37
38
39
2A
30
82
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
02
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
82
31
23
32
33
34
23
35
36
37
23
38
39
30
23
81
31
2A
32
33
34
2A
35
36
37
2A
38
39
30
83
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
01
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
00
31
32
23
33
34
35
23
36
37
38
23
39
30
Expected Sequence 1.9 (GET INPUT, digits only, SMS default alphabet, Terminal to echo text, Terminal
supporting 8 bit data Message)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.9.1
4
Terminal → USER Display "<SEND>"
5
6
USER → Terminal Completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.9.1A
Or
TERMINAL RESPONSE: GET
INPUT 1.9.1B
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 0-1
Text string coding in unpacked format.
Command performed successfully.
Release 10
199
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INPUT 1.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"<SEND>"
Response length
Minimum length:
Maximum length:
0
1
Coding:
BER-TLV:
D0
07
16
04
81
3C
03
53
01
45
23
4E
00
44
82
3E
02
91
81
02
82
00
8D
01
TERMINAL RESPONSE: GET INPUT 1.9.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
empty string
Coding:
BER-TLV:
81
8D
03
01
01
04
23
00
82
02
82
81
83
01
00
TERMINAL RESPONSE: GET INPUT 1.9.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
ETSI
Release 10
200
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Contents:
Null data object
Coding:
BER-TLV:
81
8D
03
00
01
23
00
82
02
82
81
83
01
00
Expected Sequence 1.10 (GET INPUT, null length for the text string, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 1.10.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 1.10.1
4
Terminal → USER Request for input
5
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 1.10.1
6
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help info
available.
Range of expected length is 1-5
Null Text string.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 1.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text string
Text:
length null (00).
Response length
Minimum length:
Maximum length:
1
5
Coding:
BER-TLV:
D0
00
0F
91
81
02
03
01
01
05
23
ETSI
00
82
02
81
82
8D
Release 10
201
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 1.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
27.22.4.3.1.5
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.10.
27.22.4.3.2
27.22.4.3.2.1
GET INPUT (No response from User)
Definition and applicability
See clause 3.2.2.
27.22.4.3.2.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
27.22.4.3.2.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns a "No
response from user" result value in the TERMINAL RESPONSE command send to the UICC.
27.22.4.3.2.4
Method of test
27.22.4.3.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
Terminal Manufacturers shall set the "no response from user" period of time as declared in table A.2/3.
The UICC Simulator shall be set to that period of time.
ETSI
Release 10
202
27.22.4.3.2.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 2.1 (GET INPUT, no response from the user)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 2.1.1
4
Terminal → USER Display "<TIME-OUT>"
5
6
USER
Waiting and no completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 2.1.1
Comments
Digits only, SMS default alphabet
Terminal to echo text, packing not required,
no help information available.
Range of expected length is 0-10
Text string coding in unpacked format.
No response from user within 5 s after the end
of that defined period of time.
PROACTIVE COMMAND: GET INPUT 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<TIME-OUT>"
Response length
Minimum length:
Maximum length:
0
10
Coding:
BER-TLV:
D0
0B
91
1A
04
02
81
3C
00
03
54
0A
01
49
23
4D
00
45
82
2D
02
4F
81
55
82
54
8D
3E
TERMINAL RESPONSE: GET INPUT 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Terminal
UICC
Result
General Result:
No response from user
ETSI
Release 10
203
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
27.22.4.3.2.5
81
03
01
23
00
82
02
82
81
83
01
12
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.3.3
GET INPUT (UCS2 display in Cyrillic)
27.22.4.3.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.3.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally the Terminal shall support the UCS2 facility for the coding of the Cyrillic alphabet, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.3.3.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.3.4
Method of test
27.22.4.3.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.3.3.4.2
Procedure
Expected Sequence 3.1 (GET INPUT, text string coding in UCS2 in Cyrillic, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 3.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 3.1.1
4
Terminal → USER Display " ЗДРАВСТВУЙТЕ "
5
USER → Terminal Enter the input "HELLO" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 3.1.1
6
PROACTIVE COMMAND: GET INPUT 3.1.1
Logically:
Command details
Command number:
Command type:
1
GET INPUT
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 5-5
Text string "Hello" in Russian coding in 16 bits
UCS2 alphabet format.
Command performed successfully.
Release 10
204
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
"ЗДРАВСТВУЙТЕ"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
19
04
04
28
08
21
15
81
04
04
91
03
17
22
02
01
04
04
05
23
14
12
05
01
04
04
82
20
23
02
04
04
81
10
19
82
04
04
8D
12
22
TERMINAL RESPONSE: GET INPUT 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"HELLO"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
48
01
45
82
4C
02
4C
82
4F
81
83
01
00
Expected Sequence 3.2 (GET INPUT, max length for the text string coding in UCS2 in Cyrillic, successful)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 3.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 3.2.1
Terminal → USER Display
"ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙ"
USER → Terminal Enter the input "HELLO" and
completion
ETSI
Comments
Digits only, SMS default alphabet,
Terminal to echo text, packing not
required, no help information available.
Range of expected length is 5-5
Text string length 70 characters, coding in
16 bits UCS2 alphabet format.
Release 10
Step
6
205
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 3.2.1
Comments
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 3.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
16 bit data UCS2 alphabet format
"ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙ"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
8D
04
04
04
04
04
04
04
04
04
04
04
91
81
81
12
22
12
22
12
22
12
22
12
22
12
02
9D
8D
04
04
04
04
04
04
04
04
04
04
04
05
81
08
21
15
21
15
21
15
21
15
21
15
21
05
03
04
04
04
04
04
04
04
04
04
04
04
04
01
17
22
17
22
17
22
17
22
17
22
17
22
23
04
04
04
04
04
04
04
04
04
04
04
04
01
14
12
14
12
14
12
14
12
14
12
14
12
82
04
04
04
04
04
04
04
04
04
04
04
04
02
20
23
20
23
20
23
20
23
20
23
20
23
81
04
04
04
04
04
04
04
04
04
04
04
04
82
10
19
10
19
10
19
10
19
10
19
10
19
TERMINAL RESPONSE: GET INPUT 3.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Terminal
UICC
Result
General Result:
Text string
Data coding scheme:
Command performed successfully
unpacked, 8 bit data
ETSI
Release 10
206
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
"HELLO"
Coding:
BER-TLV:
27.22.4.3.3.5
81
8D
03
06
01
04
23
48
01
45
82
4C
02
4C
82
4F
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 3.1 to 3.2.
27.22.4.3.4
GET INPUT (UCS2 entry in Cyrillic)
27.22.4.3.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.4.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally the Terminal shall support the UCS2 facility for the coding of the Cyrillic alphabet, as defined in
ISO/IEC 10646 [2].
27.22.4.3.4.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.4.4
Method of test
27.22.4.3.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.3.4.4.2
Procedure
Expected Sequence 4.1 (GET INPUT, character set from UCS2 alphabet in Cyrillic, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 4.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 4.1.1
4
Terminal → USER Display "Enter Hello"
5
USER → Terminal Enter the input
"ЗДРАВСТВУЙТЕ "
and completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 4.1.1
6
ETSI
Comments
Character set, UCS2 alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 12-12
Text string coding in unpacked format.
"Hello" in Russian, coding in UCS2 format.
Command performed successfully.
Release 10
207
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INPUT 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter Hello"
Response length
Minimum length:
Maximum length:
12
12
Coding:
BER-TLV:
D0
0C
6F
1B
04
91
81
45
02
03
6E
0C
01
74
0C
23
65
03
72
82
20
02
48
81
65
82
6C
8D
6C
TERMINAL RESPONSE: GET INPUT 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
UCS2
"ЗДРАВСТВУЙТЕ"
Coding:
BER-TLV:
81
8D
12
22
03
19
04
04
01
08
21
15
23
04
04
03
17
22
82
04
04
ETSI
02
14
12
82
04
04
81
20
23
83
04
04
01
10
19
00
04
04
Release 10
208
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 4.2 (GET INPUT, character set from UCS2 alphabet in Cyrillic, Max length for the input,
successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
GET INPUT 4.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 4.2.1
Comments
Character set, UCS2 alphabet, Terminal to echo
text, packing not required, no help information
available.
Range of expected length is no limit
Text string coding in unpacked format.
Input length 70 characters, coding in UCS2 format.
Terminal → USER Display
"Enter Hello"
USER → Terminal Enter the input
"ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙТЕ
ЗДРАВСТВУЙТЕЗДРАВСТВУЙ" and
completion
Terminal → UICC TERMINAL RESPONSE: GET INPUT Command performed successfully.
4.2.1
PROACTIVE COMMAND: GET INPUT 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter Hello"
Response length
Minimum length:
Maximum length:
5
No maximum length requirement
Coding:
BER-TLV:
D0
0C
6F
1B
04
91
81
45
02
03
6E
05
01
74
FF
23
65
03
72
82
20
02
48
81
65
82
6C
8D
6C
TERMINAL RESPONSE: GET INPUT 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Terminal
UICC
ETSI
Release 10
209
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Data coding scheme:
Text:
Command performed successfully
UCS2
"ЗДРАВСТВУЙТЕ…ЗДРАВСТВУЙ" (70 chars)
Coding:
BER-TLV:
27.22.4.3.4.5
81
8D
04
04
04
04
04
04
04
04
04
04
04
03
81
12
22
12
22
12
22
12
22
12
22
12
01
8D
04
04
04
04
04
04
04
04
04
04
04
23
08
21
15
21
15
21
15
21
15
21
15
21
03
04
04
04
04
04
04
04
04
04
04
04
04
82
17
22
17
22
17
22
17
22
17
22
17
22
02
04
04
04
04
04
04
04
04
04
04
04
04
82
14
12
14
12
14
12
14
12
14
12
14
12
81
04
04
04
04
04
04
04
04
04
04
04
04
83
20
23
20
23
20
23
20
23
20
23
20
23
01
04
04
04
04
04
04
04
04
04
04
04
04
00
10
19
10
19
10
19
10
19
10
19
10
19
Test requirement
The Terminal shall operate in the manner defined in expected sequences 4.1 to 4.2.
27.22.4.3.5
27.22.4.3.5.1
GET INPUT (default text)
Definition and applicability
See clause 3.2.2.
27.22.4.3.5.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.23.
27.22.4.3.5.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.5.4
Method of test
27.22.4.3.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
210
27.22.4.3.5.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 5.1 (GET INPUT, default text for the input, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 5.1.1
4
Terminal → USER Display "Enter 12345"
Display "12345"
5
6
USER → Terminal Completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 5.1.1
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 5-5
Text string coding in unpacked format
Default text coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Default Text
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
D0
0C
35
35
23
04
91
81
45
02
03
6E
05
01
74
05
23
65
17
00
72
06
82
20
04
02
31
31
81
32
32
82
33
33
8D
34
34
TERMINAL RESPONSE: GET INPUT 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, no help information available
Terminal
UICC
ETSI
Release 10
211
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
Expected Sequence 5.2 (GET INPUT, default text for the input with max length, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 5.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 5.2.1
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 160-160
Terminal → USER Display "Enter:"
Display default text input:
Text string coding in unpacked format
"***1111111111###***22222222 Default text length 160 bytes coding in
22###***3333333333###***4444 unpacked format.
444444###***5555555555###***
6666666666###***7777777777#
##***8888888888###***9999999
999###***0000000000###"
USER → Terminal Completion
Command performed successfully.
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 5.2.1
PROACTIVE COMMAND: GET INPUT 5.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter:"
Response length
Minimum length:
Maximum length:
160
160
Default Text
Data coding scheme:
Text:
unpacked, 8 bit data
"***1111111111###***2222222222###***3333333333###***4444444444###***
5555555555###***6666666666###***7777777777###***8888888888###***9999
999999###***0000000000###"
ETSI
Release 10
212
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
8D
A0
31
32
23
33
34
35
23
36
37
38
23
39
30
81
07
17
31
32
2A
33
34
35
2A
36
37
38
2A
39
30
BA
04
81
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
81
45
A1
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
03
6E
04
31
32
33
23
34
35
36
23
37
38
39
23
30
01
74
2A
31
32
33
2A
34
35
36
2A
37
38
39
2A
30
23
65
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
00
72
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
82
3A
31
23
32
33
34
23
35
36
37
23
38
39
30
23
02
91
31
2A
32
33
34
2A
35
36
37
2A
38
39
30
81
02
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
82
A0
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
TERMINAL RESPONSE: GET INPUT 5.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Terminal
UICC
Result
General Result:
Command performed successfully
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"***1111111111###***2222222222###***3333333333###***4444444444###***
5555555555###***6666666666###***7777777777###***8888888888###***9999
999999###***0000000000###"
Coding:
BER-TLV:
27.22.4.3.5.5
81
8D
31
32
2A
33
34
35
2A
36
37
38
2A
39
30
03
81
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
01
A1
31
32
2A
23
34
35
2A
23
37
38
2A
23
30
23
04
31
32
33
23
34
35
36
23
37
38
39
23
30
00
2A
31
32
33
2A
34
35
36
2A
37
38
39
2A
30
82
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
02
2A
23
32
33
2A
23
35
36
2A
23
38
39
2A
23
82
31
23
32
33
34
23
35
36
37
23
38
39
30
23
Test requirement
The Terminal shall operate in the manner defined in expected sequences 5.1 to 5.2.
ETSI
81
31
2A
32
33
34
2A
35
36
37
2A
38
39
30
83
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
01
31
2A
23
33
34
2A
23
36
37
2A
23
39
30
00
31
32
23
33
34
35
23
36
37
38
23
39
30
Release 10
213
27.22.4.3.6
GET INPUT (display of Icon)
27.22.4.3.6.1
Definition and applicability
ETSI TS 102 384 V10.3.0 (2015-08)
See clause 3.2.2.
27.22.4.3.6.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.5.4, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and
12.31.
27.22.4.3.6.3
Test purpose
To verify that the Terminal displays the Icon contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.6.4
Method of test
27.22.4.3.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal screen shall be in its normal stand-by display.
27.22.4.3.6.4.2
Procedure
Expected Sequence 6.1A (GET INPUT, Basic icon, self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.1.1
Terminal → USER Display the BASIC-ICON for the
prompt
USER → Terminal Enter "+" and completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.1.1A
Comments
BASIC-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<NO-ICON>"
Response length
Minimum length:
Maximum length:
0
10
ETSI
Release 10
214
Icon Identifier
Icon qualifier:
Icon identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
self-explanatory
1 (number of record in EFImg)
Coding:
BER-TLV:
D0
0A
02
1D
04
00
81
3C
0A
03
4E
1E
01
4F
02
23
2D
00
00
49
01
82
43
02
4F
81
4E
82
3E
8D
91
TERMINAL RESPONSE: GET INPUT 6.1.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
23
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.1B (GET INPUT, Basic icon, self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.1.1
Terminal → USER Display "<NO-ICON>" for the
prompt without the icon
USER → Terminal Enter "+" and completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.1.1B
Comments
BASIC-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INPUT 6.1.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
215
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result: Command performed successfully but requested icon
could not be displayed
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
23
2B
00
82
02
82
81
83
01
04
Expected Sequence 6.2A (GET INPUT, Basic icon, non self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.2.1
Terminal → USER Display "<BASIC-ICON>" and
Display the BASIC-ICON for the
prompt
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.2.1A
Comments
BASIC-ICON non self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 6.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<BASIC-ICON>"
Response length
Minimum length:
Maximum length:
0
10
Icon Identifier
Icon qualifier:
Icon identifier:
not self-explanatory
1 (number of record in EFImg)
Coding:
BER-TLV:
D0
0D
4E
20
04
3E
81
3C
91
03
42
02
01
41
00
23
53
0A
ETSI
00
49
1E
82
43
02
02
2D
01
81
49
01
82
43
8D
4F
Release 10
216
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 6.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
23
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.2B (GET INPUT, Basic icon, non self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.2.1
Terminal → USER Display "<BASIC-ICON>" for the
prompt without the icon
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.2.1B
Comments
BASIC-ICON non self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INPUT 6.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
displayed
Text string
Data coding scheme:
Command performed successfully but requested icon could not be
unpacked, 8 bit data
Text: "+"
ETSI
Release 10
217
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
8D
03
02
01
04
23
2B
00
82
02
82
81
83
01
04
Expected Sequence 6.3A (GET INPUT, Colour icon, self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.3.1
Terminal → USER Display the COLOUR-ICON for
the prompt
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.3.1A
Comments
COLOUR-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 6.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<NO-ICON>"
Response length
Minimum length:
Maximum length:
0
10
Icon Identifier
Icon qualifier:
Icon identifier:
self-explanatory
2 (number of record in EFImg)
Coding:
BER-TLV:
D0
0A
02
1D
04
00
81
3C
0A
03
4E
1E
01
4F
02
23
2D
00
00
49
02
82
43
02
4F
81
4E
82
3E
8D
91
TERMINAL RESPONSE: GET INPUT 6.3.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
218
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
23
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.3B (GET INPUT, Colour icon, self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.3.1
Terminal → USER Display "<NO-ICON>" for the
prompt without the icon
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.3.1B
Comments
COLOUR-ICON self-explanatory for the Text
string.
Text string coding in unpacked format.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INPUT 6.3.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
displayed
Command performed successfully but requested icon could not be
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
23
2B
00
82
ETSI
02
82
81
83
01
04
Release 10
219
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 6.4A (GET INPUT, Colour icon, non self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.4.1
Terminal → USER Display "<COLOUR-ICON>" and
Display the COLOUR-ICON for
the prompt
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.4.1A
Comments
COLOUR-ICON non self-explanatory for the
Text string.
Text string coding in unpacked format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 6.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"<COLOUR-ICON>"
Response length
Minimum length:
Maximum length:
0
10
Icon Identifier
Icon qualifier:
Icon identifier:
not self-explanatory
2 (number of record in EFImg)
Coding:
BER-TLV:
D0
0E
4F
21
04
4E
81
3C
3E
03
43
91
01
4F
02
23
4C
00
00
4F
0A
82
55
1E
02
52
02
81
2D
01
82
49
02
8D
43
TERMINAL RESPONSE: GET INPUT 6.4.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
220
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
81
8D
03
02
01
04
23
2B
00
82
02
82
81
83
01
00
Expected Sequence 6.4B (GET INPUT, Colour icon, non self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 6.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 6.4.1
Terminal → USER Display "<COLOUR-ICON>" for
the prompt without the icon
USER → Terminal Enter the input "+" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 6.4.1B
Comments
COLOUR-ICON non self-explanatory for the
Text string.
Text string coding in unpacked format.
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: GET INPUT 6.4.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"+"
Coding:
BER-TLV:
27.22.4.3.6.5
81
8D
03
02
01
04
23
2B
00
82
02
82
81
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 6.1A to 6.4B.
27.22.4.3.7
GET INPUT (Help Information)
27.22.4.3.7.1
Definition and applicability
See clause 3.2.2.
ETSI
83
01
04
Release 10
221
27.22.4.3.7.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
27.22.4.3.7.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns a
'help information required by the user' result value in the TERMINAL RESPONSE command sent to the UICC if the
user has indicated the need to get help information.
27.22.4.3.7.4
Method of test
27.22.4.3.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.7.4.2
Procedure
Expected Sequence 7.1 (GET INPUT, digits only, Terminal to echo text, Terminal supporting 8 bit data Message,
help information available)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 7.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 7.1.1
4
Terminal → USER Display "Enter 12345"
5
6
USER → Terminal Press "help"
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 7.1.1
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, help
information available.
Range of expected length is 5-5
Text string coding in unpacked format.
Command performed, help information
required by user.
PROACTIVE COMMAND: GET INPUT 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
ETSI
Release 10
222
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0C
35
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
80
72
82
20
02
31
81
32
82
33
8D
34
TERMINAL RESPONSE: GET INPUT 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text, help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Help information required by the user
Coding:
BER-TLV:
27.22.4.3.7.5
81
03
01
23
80
82
02
82
81
83
01
13
Test requirement
The Terminal shall operate in the manner defined in expected sequence 7.1.
27.22.4.3.8
GET INPUT (Support of Text Attribute)
27.22.4.3.8.1
GET INPUT (Support of Text Attribute - Left Alignment)
27.22.4.3.8.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.1.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.1.3
Test purpose
To verify that the Terminal displays the text formatted according to the left alignment text attribute configuration
contained in the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.3.8.1.4
Method of test
27.22.4.3.8.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
223
27.22.4.3.8.1.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 8.1 (GET INPUT, Text attribute - Left Alignment)
Step
1
2
3
4
5
6
7
8
9
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.1.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.1.2
10
Terminal → USER Display "Enter 22222"
11
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.1.2
12
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with left
alignment.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted without left
alignment. Remark: If left alignment is the
Terminal's default alignment as declared in
table A.2/7, no alignment change will take
place.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
224
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
00
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0C
32
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
ETSI
00
72
82
20
02
32
81
32
82
32
8D
32
Release 10
225
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 8.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
27.22.4.3.8.1.5
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.1.
27.22.4.3.8.2
GET INPUT (Support of Text Attribute - Center Alignment)
27.22.4.3.8.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.2.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.2.3
Test purpose
To verify that the Terminal displays the text formatted according to the center alignment text attribute configuration
contained in the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.3.8.2.4
Method of test
27.22.4.3.8.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.2.4.2
Procedure
Expected Sequence 8.2 (GET INPUT, Text attribute - Center Alignment)
Step
1
2
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.2.1
Terminal → UICC FETCH
ETSI
Comments
Release 10
Step
3
4
5
6
7
8
9
226
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.2.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.2.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.2.2
10
Terminal → USER Display "Enter 22222"
11
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.2.2
12
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with center
alignment.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted without center
alignment. Remark: If center alignment is the
Terminal's default alignment as declared in
table A.2/7, no alignment change will take
place.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Centre Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
ETSI
00
72
04
82
20
00
02
31
0B
81
32
01
82
33
B4
8D
34
Release 10
227
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 8.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0C
32
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
32
81
32
82
32
8D
32
TERMINAL RESPONSE: GET INPUT 8.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
ETSI
Release 10
228
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
27.22.4.3.8.2.5
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.2.
27.22.4.3.8.3
GET INPUT (Support of Text Attribute - Right Alignment)
27.22.4.3.8.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.3.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.3.3
Test purpose
To verify that the Terminal displays the text formatted according to the right alignment text attribute configuration
contained in the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.3.8.3.4
Method of test
27.22.4.3.8.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.3.4.2
Procedure
Expected Sequence 8.3 (GET INPUT, Text attribute - Right Alignment)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.3.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.3.1
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with right
alignment.
Command performed successfully.
Release 10
Step
7
8
9
229
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.3.2
10
Terminal → USER Display "Enter 22222"
11
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.3.2
12
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted without right
alignment. Remark: If right alignment is the
Terminal's default alignment as declared in
table A.2/7, no alignment change will take
place.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
02
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
ETSI
Release 10
230
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0C
32
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
32
81
32
82
32
8D
32
TERMINAL RESPONSE: GET INPUT 8.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Terminal
UICC
Result
General Result:
Text string
Data coding scheme:
Text:
Command performed successfully
unpacked, 8 bit data
"22222"
ETSI
Release 10
231
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
27.22.4.3.8.3.5
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.3.
27.22.4.3.8.4
GET INPUT (Support of Text Attribute - Large Font Size)
27.22.4.3.8.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.4.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.4.3
Test purpose
To verify that the Terminal displays the text formatted according to the large font size text attribute configuration
contained in the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.3.8.4.4
Method of test
27.22.4.3.8.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.4.4.2
Procedure
Expected Sequence 8.4 (GET INPUT, Text attribute - Large Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.4.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.4.2
Terminal → USER Display "Enter 22222"
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.4.2
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with large font
size.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Message shall be formatted with normal font
size.
Command performed successfully.
Release 10
Step
13
14
15
16
17
18
19
20
21
232
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.4.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.4.3
22
Terminal → USER Display "Enter 33333"
23
USER → Terminal Enter the input "33333" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.4.3
24
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with large font
size.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted with normal font
size.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
ETSI
00
72
04
82
20
00
02
31
0B
81
32
04
82
33
B4
8D
34
Release 10
233
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 8.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
32
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
ETSI
00
72
04
82
20
00
02
32
0B
81
32
00
82
32
B4
8D
32
Release 10
234
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 8.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 33333"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0C
33
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
33
81
33
82
33
8D
33
TERMINAL RESPONSE: GET INPUT 8.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
ETSI
Release 10
235
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"33333"
Coding:
BER-TLV:
27.22.4.3.8.4.5
81
8D
03
06
01
04
23
33
00
33
82
33
02
33
82
33
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.4.
27.22.4.3.8.5
GET INPUT (Support of Text Attribute - Small Font Size)
27.22.4.3.8.5.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.5.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.5.3
Test purpose
To verify that the Terminal displays the text formatted according to the small font size text attribute configuration
contained in the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.3.8.5.4
Method of test
27.22.4.3.8.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
236
27.22.4.3.8.5.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 8.5 (GET INPUT, Text attribute - Small Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.5.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.5.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.5.2
Terminal → USER Display "Enter 22222"
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.5.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.5.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.5.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.5.3
22
Terminal → USER Display "Enter 33333"
23
USER → Terminal Enter the input "33333" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.5.3
24
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with small font
size.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Message shall be formatted with normal font
size.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with small font
size.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted with normal font
size.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
ETSI
Release 10
237
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
08
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
UICC
Terminal
ETSI
Release 10
238
ETSI TS 102 384 V10.3.0 (2015-08)
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
32
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
32
0B
81
32
00
82
32
B4
8D
32
TERMINAL RESPONSE: GET INPUT 8.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 33333"
ETSI
Release 10
239
Response length
Minimum length:
Maximum length:
ETSI TS 102 384 V10.3.0 (2015-08)
5
5
Coding:
BER-TLV:
D0
0C
33
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
33
81
33
82
33
8D
33
TERMINAL RESPONSE: GET INPUT 8.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"33333"
Coding:
BER-TLV:
27.22.4.3.8.5.5
81
8D
03
06
01
04
23
33
00
33
82
33
02
33
82
33
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.5.
27.22.4.3.8.6
GET INPUT (Support of Text Attribute - Bold On)
27.22.4.3.8.6.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.6.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.6.3
Test purpose
To verify that the Terminal displays the text formatted according to the bold text attribute configuration contained in the
GET INPUT proactive UICC command, and returns a successful response in the TERMINAL RESPONSE command
sent to the UICC.
27.22.4.3.8.6.4
Method of test
27.22.4.3.8.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
ETSI
Release 10
240
ETSI TS 102 384 V10.3.0 (2015-08)
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.6.4.2
Procedure
Expected Sequence 8.6 (GET INPUT, Text attribute - Bold On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.6.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.6.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.6.2
Terminal → USER Display "Enter 22222"
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.6.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.6.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.6.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.6.3
Terminal → USER Display "Enter 33333"
USER → Terminal Enter the input "33333" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.6.3
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with bold on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Message shall be formatted with bold off.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with bold on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted with bold off.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
UICC
ETSI
Release 10
241
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
10
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
UICC
Terminal
ETSI
Release 10
242
ETSI TS 102 384 V10.3.0 (2015-08)
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
32
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
32
0B
81
32
00
82
32
B4
8D
32
TERMINAL RESPONSE: GET INPUT 8.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 33333"
ETSI
Release 10
243
Response length
Minimum length:
Maximum length:
ETSI TS 102 384 V10.3.0 (2015-08)
5
5
Coding:
BER-TLV:
D0
0C
33
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
33
81
33
82
33
8D
33
TERMINAL RESPONSE: GET INPUT 8.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"33333"
Coding:
BER-TLV:
27.22.4.3.8.6.5
81
8D
03
06
01
04
23
33
00
33
82
33
02
33
82
33
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.6.
27.22.4.3.8.7
GET INPUT (Support of Text Attribute - Italic On)
27.22.4.3.8.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.7.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.7.3
Test purpose
To verify that the Terminal displays the text formatted according to the italic text attribute configuration contained in
the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL RESPONSE
command sent to the UICC.
27.22.4.3.8.7.4
Method of test
27.22.4.3.8.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
ETSI
Release 10
244
ETSI TS 102 384 V10.3.0 (2015-08)
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.7.4.2
Procedure
Expected Sequence 8.7 (GET INPUT, Text attribute - Italic On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.7.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.7.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.7.2
Terminal → USER Display "Enter 22222"
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.7.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.7.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.7.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.7.3
Terminal → USER Display "Enter 33333"
USER → Terminal Enter the input "33333" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.7.3
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with italic on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Message shall be formatted with italic off.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with italic on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted with italic off.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
ETSI
Release 10
245
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
20
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
UICC
Terminal
ETSI
Release 10
246
ETSI TS 102 384 V10.3.0 (2015-08)
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Of
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
32
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
32
0B
81
32
00
82
32
B4
8D
32
TERMINAL RESPONSE: GET INPUT 8.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.7.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 33333"
ETSI
Release 10
247
Response length
Minimum length:
Maximum length:
ETSI TS 102 384 V10.3.0 (2015-08)
5
5
Coding:
BER-TLV:
D0
0C
33
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
33
81
33
82
33
8D
33
TERMINAL RESPONSE: GET INPUT 8.7.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"33333"
Coding:
BER-TLV:
27.22.4.3.8.7.5
81
8D
03
06
01
04
23
33
00
33
82
33
02
33
82
33
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.7.
27.22.4.3.8.8
GET INPUT (Support of Text Attribute - Underline On)
27.22.4.3.8.8.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.8.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.8.3
Test purpose
To verify that the Terminal displays the text formatted according to the underline text attribute configuration contained
in the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL RESPONSE
command sent to the UICC.
27.22.4.3.8.8.4
Method of test
27.22.4.3.8.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
ETSI
Release 10
248
ETSI TS 102 384 V10.3.0 (2015-08)
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.8.4.2
Procedure
Expected Sequence 8.8 (GET INPUT, Text attribute - Underline On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.8.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.8.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.8.2
Terminal → USER Display "Enter 22222"
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.8.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.8.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.8.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.8.3
Terminal → USER Display "Enter 33333"
USER → Terminal Enter the input "33333" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.8.3
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with underline on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Message shall be formatted with underline off.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with underline on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted with underline off.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
UICC
ETSI
Release 10
249
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
40
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
UICC
Terminal
ETSI
Release 10
250
ETSI TS 102 384 V10.3.0 (2015-08)
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
32
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
32
0B
81
32
00
82
32
B4
8D
32
TERMINAL RESPONSE: GET INPUT 8.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.8.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 33333"
ETSI
Release 10
251
Response length
Minimum length:
Maximum length:
ETSI TS 102 384 V10.3.0 (2015-08)
5
5
Coding:
BER-TLV:
D0
0C
33
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
33
81
33
82
33
8D
33
TERMINAL RESPONSE: GET INPUT 8.8.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"33333"
Coding:
BER-TLV:
27.22.4.3.8.8.5
81
8D
03
06
01
04
23
33
00
33
82
33
02
33
82
33
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.8.
27.22.4.3.8.9
GET INPUT (Support of Text Attribute - Strikethrough On)
27.22.4.3.8.9.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.9.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.9.3
Test purpose
To verify that the Terminal displays the text formatted according to the strikethrough text attribute configuration
contained in the GET INPUT proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.3.8.9.4
Method of test
27.22.4.3.8.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
ETSI
Release 10
252
ETSI TS 102 384 V10.3.0 (2015-08)
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.9.4.2
Procedure
Expected Sequence 8.9 (GET INPUT, Text attribute - Strikethrough On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.9.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.9.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.9.2
Terminal → USER Display "Enter 22222"
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.9.2
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.9.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.9.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.9.3
22
Terminal → USER Display "Enter 33333"
23
USER → Terminal Enter the input "33333" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.9.3
24
PROACTIVE COMMAND: GET INPUT 8.9.1
Logically:
Command details
Command number:
Command type:
1
GET INPUT
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with strikethrough
on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Message shall be formatted with strikethrough
off.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with strikethrough
on.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Message shall be formatted with strikethrough
off.
Command performed successfully.
Release 10
253
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
80
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
ETSI
Release 10
254
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
32
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
32
0B
81
32
00
82
32
B4
8D
32
TERMINAL RESPONSE: GET INPUT 8.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.9.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
UICC
Terminal
ETSI
Release 10
255
ETSI TS 102 384 V10.3.0 (2015-08)
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 33333"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
0C
33
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
33
81
33
82
33
8D
33
TERMINAL RESPONSE: GET INPUT 8.9.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"33333"
Coding:
BER-TLV:
27.22.4.3.8.9.5
81
8D
03
06
01
04
23
33
00
33
82
33
02
33
82
33
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.9.
27.22.4.3.8.10
GET INPUT (Support of Text Attribute - Foreground and Background Colour)
27.22.4.3.8.10.1
Definition and applicability
See clause 3.2.2.
27.22.4.3.8.10.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2, 8.15.3 and 8.70.
27.22.4.3.8.10.3
Test purpose
To verify that the Terminal displays the text formatted according to the fore- and background colour text attribute
configuration contained in the GET INPUT proactive UICC command, and returns a successful response in the
TERMINAL RESPONSE command sent to the UICC.
ETSI
Release 10
256
27.22.4.3.8.10.4
Method of test
27.22.4.3.8.10.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.3.8.10.4.2
Procedure
Expected Sequence 8.10 (GET INPUT, Text attribute - Foreground and Background Colour)
Step
1
2
3
4
5
6
7
8
9
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.10.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.10.1
Terminal → USER Display "Enter 12345"
USER → Terminal Enter the input "12345" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.10.1
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 8.10.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 8.10.2
10
Terminal → USER Display "Enter 22222"
11
USER → Terminal Enter the input "22222" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 8.10.2
12
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, text attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted according to
foreground and background colour text
attribute configuration.
Command performed successfully.
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no text
attribute.
Range of expected length is 5-5,
Text string coding in unpacked format,
Message shall be formatted with the
Terminal's default foreground and
background.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 8.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 12345"
Response length
Minimum length:
5
ETSI
Release 10
257
Maximum length:
ETSI TS 102 384 V10.3.0 (2015-08)
5
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
11
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
35
21
04
91
81
45
02
03
6E
05
01
74
05
23
65
D0
00
72
04
82
20
00
02
31
0B
81
32
00
82
33
B4
8D
34
TERMINAL RESPONSE: GET INPUT 8.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"12345"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
31
00
32
82
33
02
34
82
35
81
83
01
00
PROACTIVE COMMAND: GET INPUT 8.10.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter 22222"
Response length
Minimum length:
Maximum length:
5
5
ETSI
Release 10
258
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0C
32
1B
04
91
81
45
02
03
6E
05
01
74
05
23
65
00
72
82
20
02
32
81
32
82
32
8D
32
TERMINAL RESPONSE: GET INPUT 8.10.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
digits (0-9, *, # and +) only, SMS default alphabet, input in unpacked
format, Terminal to echo text
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"22222"
Coding:
BER-TLV:
27.22.4.3.8.10.5
81
8D
03
06
01
04
23
32
00
32
82
32
02
32
82
32
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.10.
27.22.4.3.9
27.22.4.3.9.1
GET INPUT (UCS2 display in Chinese)
Definition and applicability
See clause 3.2.2.
27.22.4.3.9.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally the Terminal shall support the UCS2 facility for the coding of the Chinese character, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.3.9.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.9.4
Method of test
27.22.4.3.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
259
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal screen shall be in its normal stand-by display.
27.22.4.3.9.4.2
Procedure
Expected Sequence 9.1 (GET INPUT, text string coding in UCS2 in Chinese, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 9.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 9.1.1
你好"
4
Terminal → USER Display "
5
USER → Terminal Enter the input "HELLO" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 9.1.1
6
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 5-5
Text string "Hello" in Chinese coding in 16 bits
UCS2 alphabet format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
16 bit data UCS2 alphabet format
Text:
"
Response length
Minimum length:
Maximum length:
你好"
5
5
Coding:
BER-TLV:
D0
05
14
08
81
4F
03
60
01
59
23
7D
01
91
82
02
02
05
81
05
82
8D
TERMINAL RESPONSE: GET INPUT 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
260
Text string
Data coding scheme:
Text:
ETSI TS 102 384 V10.3.0 (2015-08)
unpacked, 8 bit data
"HELLO"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
48
01
45
82
4C
02
4C
82
4F
81
83
01
00
Expected Sequence 9.2 (GET INPUT, max length for the text string coding in UCS2 in Chinese, successful)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 9.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 9.2.1
Terminal → USER Display
你好你好你好你好你好你好你
好你好你好你好你好你好你好
你好你好你好你好你好你好你
好你好你好你好你好你好你好
你好你好你好你好你好你好你
好你好你好"
"
5
6
USER → Terminal Enter the input "HELLO" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 9.2.1
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 5-5
Text string length 70 characters, coding in 16
bits UCS2 alphabet format
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 9.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
16 bit data UCS2 alphabet format
Text:
你好你好你好你
Response length
Minimum length:
Maximum length:
你好你好你好你好你好你好你好你好你好你好你好你好你好你
好你好你好你 好你好你好你好你好你好你好你好你好你好你好
好你好你好你 好你好"
"
5
5
ETSI
Release 10
261
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
8D
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
91
81
81
60
60
60
60
60
60
60
60
60
60
60
02
9D
8D
59
59
59
59
59
59
59
59
59
59
59
05
81
08
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
05
03
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
01
60
60
60
60
60
60
60
60
60
60
60
60
23
59
59
59
59
59
59
59
59
59
59
59
59
01
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
82
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
02
60
60
60
60
60
60
60
60
60
60
60
60
81
59
59
59
59
59
59
59
59
59
59
59
59
82
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
TERMINAL RESPONSE: GET INPUT 9.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"HELLO"
Coding:
BER-TLV:
27.22.4.3.9.5
81
8D
03
06
01
04
23
48
01
45
82
4C
02
4C
82
4F
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 9.1 to 9.2.
27.22.4.3.10
27.22.4.3.10.1
GET INPUT (UCS2 entry in Chinese)
Definition and applicability
See clause 3.2.2.
27.22.4.3.10.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally the Terminal shall support the UCS2 facility for the coding of the Chinese character, as defined in
ISO/IEC 10646 [2].
ETSI
Release 10
262
27.22.4.3.10.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.10.4
Method of test
27.22.4.3.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.3.10.4.2
Procedure
Expected Sequence 10.1 (GET INPUT, character set from UCS2 alphabet in Chinese, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 10.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 10.1.1
4
Terminal → USER Display "Enter Hello"
5
USER → Terminal Enter the input "
"
and completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 10.1.1
6
你好
Comments
Character set, UCS2 alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 2-2
Text string coding in unpacked format
"Hello" in Chinese, coding in UCS2 format
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter Hello"
Response length
Minimum length:
Maximum length:
2
2
Coding:
BER-TLV:
D0
0C
6F
1B
04
91
81
45
02
03
6E
02
01
74
02
23
65
ETSI
03
72
82
20
02
48
81
65
82
6C
8D
6C
Release 10
263
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET INPUT 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
UCS2
Text:
"
你好"
Coding:
BER-TLV:
81
8D
03
05
01
08
23
4F
03
60
82
59
02
7D
82
81
83
01
00
Expected Sequence 10.2 (GET INPUT, character set from UCS2 alphabet in Chinese, Max length for the input,
successful)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 10.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 10.2.1
Terminal → USER Display
"Enter Hello"
USER → Terminal Enter the input
你好你好你好你好你好你好你
好你好你好你好你好你好你好
你好你好你好你好你好你好你
好你好你好你好你好你好你好
你好你好你好你好你好你好你
好你好你好" and completion
"
6
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 10.2.1
Comments
Character set, UCS2 alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is no limit
Text string coding in unpacked format.
Input length 70 characters, coding in UCS2
format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 10.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
ETSI
Release 10
264
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter Hello"
Response length
Minimum length:
Maximum length:
5
No maximum length requirement
Coding:
BER-TLV:
D0
0C
6F
1B
04
91
81
45
02
03
6E
05
01
74
FF
23
65
03
72
82
20
02
48
81
65
82
6C
8D
6C
TERMINAL RESPONSE: GET INPUT 10.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Data coding scheme:
Command performed successfully
UCS2
你好你好你好你好你好你好你好你好你好你好你好你好你好你
好你好你好你好你好你好你好你好你好你好你好你好你好你好你
好你好你好你好你好你好你好你好" (70 chars)
Text:
"
Coding:
BER-TLV:
27.22.4.3.10.5
81
8D
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
03
81
60
60
60
60
60
60
60
60
60
60
60
01
8D
59
59
59
59
59
59
59
59
59
59
59
23
08
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
03
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
82
60
60
60
60
60
60
60
60
60
60
60
60
02
59
59
59
59
59
59
59
59
59
59
59
59
82
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
81
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
4F
Test requirement
The Terminal shall operate in the manner defined in expected sequences 10.1 to 10.2.
ETSI
83
60
60
60
60
60
60
60
60
60
60
60
60
01
59
59
59
59
59
59
59
59
59
59
59
59
00
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
7D
Release 10
265
27.22.4.3.11
27.22.4.3.11.1
ETSI TS 102 384 V10.3.0 (2015-08)
GET INPUT (UCS2 display in Katakana)
Definition and applicability
See clause 3.2.2.
27.22.4.3.11.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally the Terminal shall support the UCS2 facility for the coding of the Katakana character, as defined in the
following technical specifications: ISO/IEC 10646 [2].
27.22.4.3.11.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.11.4
Method of test
27.22.4.3.11.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.3.11.4.2
Procedure
Expected Sequence 11.1 (GET INPUT, text string coding in UCS2 in Katakana, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 11.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 11.1.1
ル"
4
Terminal → USER Display "
5
USER → Terminal Enter the input "HELLO" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 11.1.1
6
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 5-5
Text string character in Katakana coding in 16
bits UCS2 alphabet format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 11.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
UICC
Terminal
ETSI
Release 10
266
Text String
Data coding scheme:
ETSI TS 102 384 V10.3.0 (2015-08)
16 bit data UCS2 alphabet format
Text:
"
Response length
Minimum length:
Maximum length:
ル"
5
5
Coding:
BER-TLV:
D0
03
12
08
81
30
03
EB
01
91
23
02
01
05
82
05
02
81
82
8D
TERMINAL RESPONSE: GET INPUT 11.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
unpacked, 8 bit data
"HELLO"
Coding:
BER-TLV:
81
8D
03
06
01
04
23
48
01
45
82
4C
02
4C
82
4F
81
83
01
00
Expected Sequence 11.2 (GET INPUT, max length for the text string coding in UCS2 in Katakana, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 11.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 11.2.1
4
Terminal → USER Display
"
5
USER → Terminal Enter the input "HELLO" and
completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 11.2.1
6
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル"
ETSI
Comments
Digits only, SMS default alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 5-5
Text string length 70 characters, coding in 16
bits UCS2 alphabet format.
Command performed successfully.
Release 10
267
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INPUT 11.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
16 bit data UCS2 alphabet format
ルルルルルルルルルルルルルルルルルルルルルルルルルルル
ルルルルルルルルルルルルルルルルルルルルルルルルルルルル
ルルルルルルルルルルルルルルル"
Text:
"
Response length
Minimum length:
Maximum length:
5
5
Coding:
BER-TLV:
D0
8D
30
30
30
30
30
30
30
30
30
30
30
91
81
81
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
02
9D
8D
30
30
30
30
30
30
30
30
30
30
30
05
81
08
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
05
03
30
30
30
30
30
30
30
30
30
30
30
30
01
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
23
30
30
30
30
30
30
30
30
30
30
30
30
01
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
82
30
30
30
30
30
30
30
30
30
30
30
30
02
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
81
30
30
30
30
30
30
30
30
30
30
30
30
82
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
TERMINAL RESPONSE: GET INPUT 11.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
GET INPUT
alphabet set, SMS default alphabet, input in unpacked format,
Terminal to echo text, no help information available
Terminal
UICC
Result
General Result:
Text string
Data coding scheme:
Text:
Command performed successfully
unpacked, 8 bit data
"HELLO"
ETSI
Release 10
268
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
27.22.4.3.11.5
81
8D
03
06
01
04
23
48
01
45
82
4C
02
4C
82
4F
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 11.1 to 11.2.
27.22.4.3.12
27.22.4.3.12.1
GET INPUT (UCS2 entry in Katakana)
Definition and applicability
See clause 3.2.2.
27.22.4.3.12.2
Conformance requirement
The Terminal shall support the GET INPUT command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.11, 8.15, 8.15.1, 8.15.2 and 8.15.3.
Additionally the Terminal shall support the UCS2 facility for the coding of the Katakana character, as defined in
ISO/IEC 10646 [2].
27.22.4.3.12.3
Test purpose
To verify that the Terminal displays the text contained in the GET INPUT proactive UICC command, and returns the
text string entered in the TERMINAL RESPONSE command sent to the UICC.
27.22.4.3.12.4
Method of test
27.22.4.3.12.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.3.12.4.2
Procedure
Expected Sequence 12.1 (GET INPUT, character set from UCS2 alphabet in Katakana, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 12.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 12.1.1
4
Terminal → USER Display "Enter Hello"
5
"
USER → Terminal Enter the input "
and completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 12.1.1
6
ルル
ETSI
Comments
Character set, UCS2 alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is 2-2
Text string coding in unpacked format.
Characters in Katakana, coding in UCS2
format.
Command performed successfully.
Release 10
269
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET INPUT 12.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter Hello"
Response length
Minimum length:
Maximum length:
2
2
Coding:
BER-TLV:
D0
0C
6F
1B
04
91
81
45
02
03
6E
02
01
74
02
23
65
03
72
82
20
02
48
81
65
82
6C
8D
6C
TERMINAL RESPONSE: GET INPUT 12.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Text string
Data coding scheme:
Text:
UCS2
"
"
ルル
Coding:
BER-TLV:
81
8D
03
05
01
08
23
30
03
EB
82
30
ETSI
02
EB
82
81
83
01
00
Release 10
270
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 12.2 (GET INPUT, character set from UCS2 alphabet in Katakana, Max length for the input,
successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: GET INPUT 12.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET
INPUT 12.2.1
Terminal → USER Display
"Enter Hello"
USER → Terminal Enter the input
"
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル
ルルルルルルルルルルルルルル"
and completion
Terminal → UICC TERMINAL RESPONSE: GET
INPUT 12.2.1
Comments
Character set, UCS2 alphabet, Terminal to
echo text, packing not required, no help
information available.
Range of expected length is no limit
Text string coding in unpacked format.
Input length 70 characters, coding in UCS2
format.
Command performed successfully.
PROACTIVE COMMAND: GET INPUT 12.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Enter Hello"
Response length
Minimum length:
Maximum length:
5
No maximum length requirement
Coding:
BER-TLV:
D0
0C
6F
1B
04
91
81
45
02
03
6E
05
01
74
FF
23
65
03
72
82
20
02
48
81
65
82
6C
8D
6C
TERMINAL RESPONSE: GET INPUT 12.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET INPUT
character set, UCS2 alphabet, input in unpacked format, Terminal to
echo text, no help information available
ETSI
Release 10
271
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Data coding scheme:
Command performed successfully
UCS2
ルルルルルルルルルルルルルルルルルルルルルルルルルルル
ルルルルルルルルルルルルルルルルルルルルルルルルルルルルルル
Text:
"
ル
ルルルルルルルルルルルル" (70 chars)
Coding:
BER-TLV:
27.22.4.3.12.5
81
8D
30
30
30
30
30
30
30
30
30
30
30
03
81
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
01
8D
30
30
30
30
30
30
30
30
30
30
30
23
08
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
03
30
30
30
30
30
30
30
30
30
30
30
30
82
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
02
30
30
30
30
30
30
30
30
30
30
30
30
82
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
81
30
30
30
30
30
30
30
30
30
30
30
30
83
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
01
30
30
30
30
30
30
30
30
30
30
30
30
00
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
EB
Test requirement
The Terminal shall operate in the manner defined in expected sequences 12.1 to 12.2.
27.22.4.4
27.22.4.4.1
MORE TIME
Definition and applicability
See clause 3.2.2.
27.22.4.4.2
Conformance requirement
The Terminal shall support the MORE TIME command as defined in:
•
ETSI TS 102 223 [1], clauses 6.4.4, 6.6.4, 5.2, 8.6 and 8.7.
27.22.4.4.3
Test purpose
To verify that the Terminal shall send a TERMINAL RESPONSE (OK) to the UICC after the Terminal receives the
MORE TIME proactive UICC command.
27.22.4.4.4
27.22.4.4.4.1
Method of test
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
272
27.22.4.4.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 1.1 (MORE TIME)
Step
1
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: MORE TIME 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: MORE
TIME 1.1.1
Terminal → UICC TERMINAL RESPONSE: MORE
TIME 1.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
2
3
4
5
Comments
Command performed successfully.
PROACTIVE COMMAND: MORE TIME 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
MORE TIME
"00"
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
02
00
82
02
81
82
TERMINAL RESPONSE: MORE TIME 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
MORE TIME
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.4.5
81
03
01
02
00
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 1.1.
27.22.4.5
27.22.4.5.1
27.22.4.5.1.1
PLAY TONE
PLAY TONE (Normal)
Definition and applicability
See clause 3.2.2.
ETSI
82
81
83
01
00
Release 10
273
27.22.4.5.1.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16 and 8.8.
27.22.4.5.1.3
Test purpose
To verify that the Terminal plays an audio tone of a type and duration contained in the PLAY TONE proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that the Terminal plays the requested audio tone through the earpiece whilst not in call and shall superimpose
the tone on top of the downlink audio whilst in call.
To verify that the Terminal displays the text contained in the PLAY TONE proactive UICC command.
27.22.4.5.1.4
Method of test
27.22.4.5.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.1.4.2
Procedure
Expected Sequence 1.1 (PLAY TONE)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 1.1.1
Terminal → USER Display "Dial Tone"
5
Terminal → UICC
6
UICC → Terminal
7
UICC → Terminal
8
9
Terminal → UICC
UICC → Terminal
10
Terminal → USER
11
Terminal → UICC
12
UICC → Terminal
13
UICC → Terminal
14
15
Terminal → UICC
UICC → Terminal
Comments
Play a standard supervisory dial
tone through the external ringer for
a duration of 5 s
TERMINAL RESPONSE: PLAY
Command performed successfully.
TONE 1.1.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.2
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.2
Display "Sub. Busy"
Play a standard supervisory called
subscriber busy tone for a duration
of 5 s
TERMINAL RESPONSE: PLAY
Command performed successfully.
TONE 1.1.2
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.3
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.3
ETSI
Release 10
Step
16
274
Direction
Message/Action
Terminal → USER Display "Congestion"
17
Terminal → UICC
18
UICC → Terminal
19
UICC → Terminal
20
21
Terminal → UICC
UICC → Terminal
22
Terminal → USER
23
Terminal → UICC
24
UICC → Terminal
25
UICC → Terminal
26
27
Terminal → UICC
UICC → Terminal
28
Terminal → USER
29
Terminal → UICC
30
UICC → Terminal
31
UICC → Terminal
32
33
Terminal → UICC
UICC → Terminal
34
Terminal → USER
35
Terminal → UICC
36
UICC → Terminal
37
UICC → Terminal
38
39
Terminal → UICC
UICC → Terminal
40
Terminal → USER
41
42
43
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Play a standard supervisory
congestion tone for a duration of 5
s
TERMINAL RESPONSE: PLAY
Command performed successfully.
TONE 1.1.3
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.4
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.4
Display "RP Ack"
Play a standard supervisory radio
path acknowledgement tone
TERMINAL RESPONSE: PLAY
TONE 1.1.4
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.5
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.5
Display "No RP"
Play a standard supervisory radio
path not available/call dropped
tone for a duration of 5 s
TERMINAL RESPONSE: PLAY
TONE 1.1.5
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.6
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.6
Display "Spec Info"
Command performed successfully.
Command performed successfully.
Play a standard supervisory
error/special information tone for a
duration of 5 s
TERMINAL RESPONSE: PLAY
Command performed successfully.
TONE 1.1.6
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.7
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.7
Display "Call Wait"
Play a standard supervisory call
waiting tone for a duration of 5 s
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 1.1.7
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.8
ETSI
Command performed successfully.
Release 10
Step
44
45
46
275
Direction
Message/Action
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 1.1.8
Terminal → USER Display "Ring Tone"
47
Terminal → UICC
48
UICC → Terminal
49
UICC → Terminal
50
51
Terminal → UICC
UICC → Terminal
52
Terminal → USER
53
54
55
56
57
58
59
60
UICC → Terminal
61
UICC → Terminal
62
63
Terminal → UICC
UICC → Terminal
64
Terminal → USER
65
66
Comments
Play a standard supervisory
ringing tone for duration of 5 s
TERMINAL RESPONSE: PLAY
Command performed successfully.
TONE 1.1.8
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.9
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.9
Display "This command instructs
the ME to play an audio tone.
Upon receiving this command, the
ME shall check if it is currently in,
or in the process of setting up
(SET-UP message sent to the
network, see GSM"04.08"(8)), a
speech call. - If the ME I"
Play a general beep
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 1.1.9a
or
TERMINAL RESPONSE: PLAY
TONE 1.1.9b
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.10
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 1.1.10
Terminal → USER Display "Beep"
Terminal → UICC
ETSI TS 102 384 V10.3.0 (2015-08)
Play a Terminal proprietary
general beep
TERMINAL RESPONSE: PLAY
TONE 1.1.10a
Or
TERMINAL RESPONSE: PLAY
TONE 1.1.10b
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.11
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.11
Display "Positive"
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 1.1.11a
or
TERMINAL RESPONSE: PLAY
TONE 1.1.11b
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
Command performed successfully.
or
Command beyond Terminal's capabilities.
Command performed successfully.
or
Command beyond Terminal's capabilities.
Command performed successfully.
or
Command beyond Terminal's capabilities.
Release 10
Step
67
68
69
70
71
276
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.12
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 1.1.12
Terminal → USER Display "Negative"
Terminal → UICC
72
UICC → Terminal
73
UICC → Terminal
74
75
Terminal → UICC
UICC → Terminal
76
Terminal → USER
77
Terminal → UICC
78
UICC → Terminal
79
UICC → Terminal
80
81
Terminal → UICC
UICC → Terminal
82
Terminal → USER
Play a Terminal proprietary
negative acknowledgement tone
TERMINAL RESPONSE: PLAY
TONE 1.1.12a
or
TERMINAL RESPONSE: PLAY
TONE 1.1.12b
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.13
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.13
Display "Quick"
Play a Terminal proprietary
general beep
TERMINAL RESPONSE: PLAY
TONE 1.1.13a
or
TERMINAL RESPONSE: PLAY
TONE 1.1.13b
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.14
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.14
Display "<ABORT>"
Play a Terminal Error/Special
information tone for 1 minute until
user aborts this command
TERMINAL RESPONSE: PLAY
TONE 1.1.14
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 1.1.15
FETCH
PROACTIVE COMMAND: PLAY
TONE 1.1.15
Terminal plays general beep, or if
not supported any (defined by
Terminal-manufacturer) other
supported tone
TERMINAL RESPONSE: PLAY
TONE 1.1.15
83
Terminal → UICC
84
UICC → Terminal
85
UICC → Terminal
86
87
Terminal → UICC
UICC → Terminal
88
Terminal → User
89
Terminal → UICC
90
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command performed successfully.
or
Command beyond Terminal's capabilities.
Command performed successfully.
or
Command beyond Terminal's capabilities.
Proactive UICC session terminated by the
user.
No alpha identifier, no tone tag, no duration
tag.
Terminal uses default duration defined by
Terminal-manufacturer.
Command performed successfully, Terminal
uses general beep, or if not supported any
(defined by Terminal-manufacturer) other
supported tone, uses default duration defined
by Terminal-manufacturer.
Release 10
277
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Dial Tone"
Standard supervisory tones: dial tone
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
09
01
1B
44
84
81
69
02
03
61
01
01
6C
05
20
20
00
54
82
6F
02
6E
81
65
03
8E
85
01
PROACTIVE COMMAND: PLAY TONE 1.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Sub. Busy"
Standard supervisory tones: called subscriber busy
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
09
02
1B
53
84
81
75
02
03
62
01
01
2E
05
20
20
00
42
82
75
02
73
PROACTIVE COMMAND: PLAY TONE 1.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Congestion"
Standard supervisory tones: congestion
ETSI
81
79
03
8E
85
01
Release 10
278
Duration
Time unit:
Time interval:
ETSI TS 102 384 V10.3.0 (2015-08)
Seconds
5
Coding:
BER-TLV:
D0
0A
01
1C
43
03
81
6F
84
03
6E
02
01
67
01
20
65
05
00
73
82
74
02
69
81
6F
03
6E
85
8E
PROACTIVE COMMAND: PLAY TONE 1.1.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"RP Ack"
Standard supervisory tones: radio path acknowledge
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
06
01
18
52
05
81
50
03
20
01
41
20
63
00
6B
82
8E
02
01
81
04
03
84
85
02
PROACTIVE COMMAND: PLAY TONE 1.1.5
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"No RP"
Standard supervisory tones: radio path not available
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
05
05
17
4E
81
6F
03
20
01
52
20
50
ETSI
00
8E
82
01
02
05
81
84
03
02
85
01
Release 10
279
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 1.1.6
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Spec Info"
Standard supervisory tones: Error/ special information
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
09
06
1B
53
84
81
70
02
03
65
01
01
63
05
20
20
00
49
82
6E
02
66
81
6F
03
8E
85
01
03
8E
85
01
PROACTIVE COMMAND: PLAY TONE 1.1.7
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Call Wait"
Standard supervisory tones: call waiting tone
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
09
07
1B
43
84
81
61
02
03
6C
01
01
6C
05
20
20
00
57
82
61
02
69
PROACTIVE COMMAND: PLAY TONE 1.1.8
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Ring Tone"
Standard supervisory tones: ringing tone
ETSI
81
74
Release 10
280
Duration
Time unit:
Time interval:
ETSI TS 102 384 V10.3.0 (2015-08)
Seconds
5
Coding:
BER-TLV:
D0
09
08
1B
52
84
81
69
02
03
6E
01
01
67
05
20
20
00
54
82
6F
02
6E
81
65
03
8E
85
01
PROACTIVE COMMAND: PLAY TONE 1.1.9
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Earpiece
"This command instructs the ME to play an audio tone. Upon
receiving this command, the ME shall check if it is currently in, or in
the process of setting up (SET-UP message sent to the network, see
GSM"04.08"(8)), a speech call. - If the ME I"
Coding:
BER-TLV:
D0
85
61
73
70
6F
20
68
20
6C
74
6C
20
20
75
65
74
72
30
61
6C
4D
81
81
6E
20
6C
20
72
69
74
20
20
79
74
6F
70
73
6F
6B
34
20
2E
45
FD
F1
64
74
61
74
65
73
68
63
69
20
68
66
20
73
20
2C
2E
73
20
20
81
54
20
68
79
6F
63
20
65
68
73
69
65
20
28
61
74
20
30
70
2D
49
03
68
69
65
20
6E
65
63
20
65
20
6E
20
73
53
67
68
73
38
65
20
01
69
6E
20
61
65
69
6F
4D
63
63
2C
70
65
45
65
65
65
22
65
49
PROACTIVE COMMAND: PLAY TONE 1.1.10
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
ETSI
20
73
73
4D
6E
2E
76
6D
45
6B
75
20
72
74
54
20
20
65
28
63
66
00
20
74
45
20
20
69
6D
20
20
72
6F
6F
74
2D
73
6E
20
38
68
20
82
63
72
20
61
55
6E
61
73
69
72
72
63
69
55
65
65
47
29
20
74
02
6F
75
74
75
70
67
6E
68
66
65
20
65
6E
50
6E
74
53
29
63
68
81
6D
63
6F
64
6F
20
64
61
20
6E
69
73
67
20
74
77
4D
2C
61
65
03
6D
74
20
69
6E
74
2C
6C
69
74
6E
73
20
6D
20
6F
22
20
6C
20
Release 10
281
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Beep"
Terminal proprietary tones: general beep
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
04
16
42
81
65
03
65
01
70
20
8E
00
01
82
10
02
84
81
02
03
01
85
01
PROACTIVE COMMAND: PLAY TONE 1.1.11
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Positive"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
08
84
1A
50
02
81
6F
01
03
73
01
01
69
20
74
00
69
82
76
02
65
81
8E
03
01
85
11
PROACTIVE COMMAND: PLAY TONE 1.1.12
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Negative"
Terminal proprietary tones: negative acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
08
84
1A
4E
02
81
65
01
03
67
01
01
61
20
74
ETSI
00
69
82
76
02
65
81
8E
03
01
85
12
Release 10
282
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 1.1.13
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Quick"
Terminal proprietary tones: general beep
Duration
Time unit:
Time interval:
Tenths of seconds
2
Coding:
BER-TLV:
D0
05
02
17
51
81
75
03
69
01
63
20
6B
00
8E
82
01
02
10
81
84
03
02
85
02
PROACTIVE COMMAND: PLAY TONE 1.1.14
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"<ABORT>"
Standard supervisory tones: Error/Special information
Duration
Time unit:
Time interval:
Minutes
1
Coding:
BER-TLV:
D0
07
02
19
3C
00
81
41
01
03
42
01
4F
20
52
PROACTIVE COMMAND: PLAY TONE 1.1.15
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
UICC
Earpiece
ETSI
00
54
82
3E
02
8E
81
01
03
06
85
84
Release 10
283
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
09
81
03
01
20
00
82
02
81
03
83
01
00
83
01
00
01
30
TERMINAL RESPONSE: PLAY TONE 1.1.1... 1.1.8, 1.1.15
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
TERMINAL RESPONSE: PLAY TONE 1.1.9a... 1.1.13a
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
TERMINAL RESPONSE: PLAY TONE 1.1.9b..1.1.13b
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command beyond Terminal's capabilities
Coding:
BER-TLV:
81
03
01
20
00
82
ETSI
02
82
81
83
Release 10
284
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: PLAY TONE 1.1.14
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Proactive UICC session terminated by user
Coding:
BER-TLV:
27.22.4.5.1.5
81
03
01
20
00
82
02
82
81
83
01
10
Test requirement
The Terminal shall operate in the manner defined in expected sequence 1.1.
27.22.4.5.2
PLAY TONE (UCS2 display in Cyrillic)
27.22.4.5.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.2.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.2, 8.16 and 8.8.
Additionally the Terminal shall support the UCS2 facility for the coding of the Cyrillic alphabet, as defined in
ISO/IEC 10646 [2].
27.22.4.5.2.3
Test purpose
To verify that the Terminal displays the text contained in the PLAY TONE proactive UICC command, and returns a
successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that the Terminal plays the requested audio tone through the earpiece.
27.22.4.5.2.4
Method of test
27.22.4.5.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.2.4.2
Procedure
Expected Sequence 2.1 (PLAY TONE, character set from UCS2 alphabet in Cyrillic, successful)
Step
1
2
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 2.1.1
Terminal → UICC FETCH
ETSI
Comments
Release 10
Step
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
285
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 2.1.1
Terminal → USER Display "ЗДРАВСТВУЙТЕ"
and play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 2.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 2.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 2.1.2
Terminal → USER Display "ЗДРАВСТВУЙТЕ"
and play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 2.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 2.1.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 2.1.3
Terminal → USER Display "ЗДРАВСТВУЙТЕ"
and play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 2.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
UCS2 alphabet.
"Hello" in Russian, 0x80 coding of UCS2
format.
Command performed successfully.
UCS2 alphabet.
"Hello" in Russian, 0x81 coding of UCS2
format.
Command performed successfully.
UCS2 alphabet.
"Hello" in Russian, 0x82 coding of UCS2
format.
Command performed successfully.
PROACTIVE COMMAND: PLAY TONE 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"ЗДРАВСТВУЙТЕ"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
19
04
04
2B
80
21
15
81
04
04
8E
03
17
22
01
01
04
04
11
20
14
12
84
ETSI
00
04
04
02
82
20
23
01
02
04
04
01
81
10
19
03
04
04
85
12
22
Release 10
286
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 2.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"ЗДРАВСТВУЙТЕ"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
0F
A3
21
81
99
81
0C
A2
03
08
95
01
97
8E
20
94
01
00
A0
11
82
90
84
02
92
02
81
A1
01
03
A2
01
85
92
PROACTIVE COMMAND: PLAY TONE 2.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"ЗДРАВСТВУЙТЕ"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
10
82
22
82
93
81
0C
89
03
04
92
01
10
85
20
87
8E
TERMINAL RESPONSE: PLAY TONE 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
00
84
01
82
90
11
02
80
84
81
82
02
03
91
01
85
92
01
Release 10
287
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.5.2.5
81
03
01
20
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.5.3
PLAY TONE (display of Icon)
27.22.4.5.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.3.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8 and 8.31.
27.22.4.5.3.3
Test purpose
To verify that the Terminal plays an audio tone of a type and duration contained in the PLAY TONE proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that the Terminal plays the requested audio tone through the earpiece.
To verify that the Terminal displays the icon contained in the PLAY TONE proactive UICC command.
27.22.4.5.3.4
Method of test
27.22.4.5.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.3.4.2
Procedure
Expected Sequence 3.1A (PLAY TONE, Basic icon, self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY BASIC-ICON self-explanatory.
TONE 3.1.1
Terminal → USER Display the basic icon without the
alpha identifier
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.1.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
Command performed successfully.
Release 10
288
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"<BASIC-ICON>"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Icon Identifier
Icon qualifier:
Icon identifier:
self-explanatory
1 (number of record in EFImg)
Coding:
BER-TLV:
D0
0C
3E
22
3C
8E
81
42
01
03
41
11
01
53
84
20
49
02
00
43
01
82
2D
01
02
49
1E
81
43
02
03
4F
00
85
4E
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 3.1.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
Expected Sequence 3.1B (PLAY TONE, Basic icon, self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY BASIC-ICON self-explanatory.
TONE 3.1.1
Terminal → USER Display "<BASIC-ICON>" without
the icon
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.1.1B
ETSI
Command performed successfully, but
requested icon could not be displayed.
Release 10
Step
6
289
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
TERMINAL RESPONSE: PLAY TONE 3.1.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
83
01
04
Expected Sequence 3.2A (PLAY TONE, Basic icon, non self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY BASIC-ICON non self-explanatory.
TONE 3.2.1
Terminal → USER Display "<BASIC-ICON>" and
the basic icon
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.2.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Command performed successfully.
PROACTIVE COMMAND: PLAY TONE 3.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
'<BASIC-ICON>'
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
ETSI
Release 10
290
Icon Identifier
Icon qualifier:
Icon identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
non self-explanatory
1 (number of record in EFImg)
Coding:
BER-TLV:
D0
0C
3E
22
3C
8E
81
42
01
03
41
11
01
53
84
20
49
02
00
43
01
82
2D
01
02
49
1E
81
43
02
03
4F
01
85
4E
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 3.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
Expected Sequence 3.2B (PLAY TONE, Basic icon, non self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY BASIC-ICON non self-explanatory.
TONE 3.2.1
Terminal → USER Display "<BASIC-ICON>" without
the basic icon
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.2.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
TERMINAL RESPONSE: PLAY TONE 3.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Command performed successfully, but
requested icon could not be displayed.
Release 10
291
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
83
01
04
Expected Sequence 3.3A (PLAY TONE, Colour icon, self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY COLOUR-ICON self-explanatory.
TONE 3.3.1
Terminal → USER Display the COLOUR-ICON
without the alpha identifier
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.3.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Command performed successfully.
PROACTIVE COMMAND: PLAY TONE 3.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"<COLOUR-ICON>"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Icon Identifier
Icon qualifier:
Icon identifier:
self-explanatory
2 (number of record in EFImg)
Coding:
BER-TLV:
D0
0D
4E
02
23
3C
3E
81
43
8E
03
4F
01
01
4C
11
20
4F
84
TERMINAL RESPONSE: PLAY TONE 3.3.1A
Logically:
Command details
Command number:
Command type:
1
PLAY TONE
ETSI
00
55
02
82
52
01
02
2D
01
81
49
1E
03
43
02
85
4F
00
Release 10
292
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
83
01
00
Expected Sequence 3.3B (PLAY TONE, Colour icon, self-explanatory, requested icon could not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY COLOUR-ICON self-explanatory.
TONE 3.3.1
Terminal → USER Display "<COLOUR-ICON>"
without the colour icon
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.3.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: PLAY TONE 3.3.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
20
00
82
ETSI
02
82
81
83
01
04
Release 10
293
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 3.4A (PLAY TONE, Colour icon, non self-explanatory, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY COLOUR-ICON non self-explanatory.
TONE 3.4.1
Terminal → USER Display "<COLOUR-ICON>" and
the colour icon
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.4.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Command performed successfully.
PROACTIVE COMMAND: PLAY TONE 3.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"<COLOUR-ICON>"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Icon Identifier
Icon qualifier:
Icon identifier:
not self-explanatory
2 (number of record in EFImg)
Coding:
BER-TLV:
D0
0D
4E
02
23
3C
3E
81
43
8E
03
4F
01
01
4C
11
20
4F
84
00
55
02
82
52
01
02
2D
01
TERMINAL RESPONSE: PLAY TONE 3.4.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
81
49
1E
03
43
02
85
4F
01
Release 10
294
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
83
01
00
Expected Sequence 3.4B (PLAY TONE, Colour icon, non self-explanatory, requested icon could not be
displayed)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 3.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY COLOUR-ICON non self-explanatory.
TONE 3.4.1
Terminal → USER Display "<COLOUR-ICON>"
without the colour icon
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 3.4.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
5
6
Command performed successfully, but
requested icon could not be displayed.
TERMINAL RESPONSE: PLAY TONE 3.4.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully, but requested icon could not be
displayed
Coding:
BER-TLV:
27.22.4.5.3.5
81
03
01
20
00
82
02
82
81
83
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 3.1A to 3.4B.
27.22.4.5.4
PLAY TONE (Support of Text Attribute)
27.22.4.5.4.1
PLAY TONE (Support of Text Attribute - Left Alignment)
27.22.4.5.4.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.1.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
ETSI
04
Release 10
295
27.22.4.5.4.1.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text formatted according to the left alignment text attribute configuration
contained in the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.5.4.1.4
Method of test
27.22.4.5.4.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.1.4.2
Procedure
Expected Sequence 4.1 (PLAY TONE, Text Attribute - Left Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.1.1
Message shall be formatted with left
Terminal → USER Display 'Text Attribute 1'
alignment.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.1.2
Message shall be formatted without left
Terminal → USER Display 'Text Attribute 2'
alignment. Remark: If left alignment is the
Play a Terminal proprietary
Terminal's default alignment as declared in
positive acknowledgement tone table A.2/8, no alignment change will take
place.
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: PLAY TONE 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
ETSI
Release 10
296
Duration
Time unit:
Time interval:
ETSI TS 102 384 V10.3.0 (2015-08)
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
00
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
PROACTIVE COMMAND: PLAY TONE 4.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
32
20
20
8E
ETSI
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Release 10
297
27.22.4.5.4.1.5
ETSI TS 102 384 V10.3.0 (2015-08)
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.1.
27.22.4.5.4.2
PLAY TONE (Support of Text Attribute - Center Alignment)
27.22.4.5.4.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.2.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
27.22.4.5.4.2.3
Test purpose
To verify that the Terminal displays the text formatted according to the center alignment text attribute configuration
contained in the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.5.4.2.4
Method of test
27.22.4.5.4.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.2.4.2
Procedure
Expected Sequence 4.2 (PLAY TONE, Text Attribute - Centre Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.2.1
Message shall be formatted with center
Terminal → USER Display 'Text Attribute 1'
alignment.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.2.2
Message shall be formatted without center
Terminal → USER Display 'Text Attribute 2'
alignment. Remark: If center alignment is the
Play a Terminal proprietary
Terminal's default alignment as declared in
positive acknowledgement tone table A.2/8, no alignment change will take
place.
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
Release 10
298
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Centre Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
01
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
PROACTIVE COMMAND: PLAY TONE 4.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
ETSI
02
82
81
Release 10
299
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.2.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
32
20
20
8E
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.2.
27.22.4.5.4.3
PLAY TONE (Support of Text Attribute - Right Alignment)
27.22.4.5.4.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.3.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
27.22.4.5.4.3.3
Test purpose
To verify that the Terminal displays the text formatted according to the right alignment text attribute configuration
contained in the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.5.4.3.4
Method of test
27.22.4.5.4.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.3.4.2
Procedure
Expected Sequence 4.3 (PLAY TONE, Text Attribute - Right Alignment)
Step
1
2
3
4
5
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.3.1
Message shall be formatted with right
Terminal → USER Display 'Text Attribute 1'
alignment.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.3.1
ETSI
Release 10
Step
6
1
2
3
4
5
6
300
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.3.2
Message shall be formatted without right
Terminal → USER Display 'Text Attribute 2'
alignment. Remark: If right alignment is the
Play a Terminal proprietary
Terminal's default alignment as declared in
positive acknowledgement tone table A.2/8, no alignment change will take
place.
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.3.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: PLAY TONE 4.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
02
20
20
8E
B4
TERMINAL RESPONSE: PLAY TONE 4.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Release 10
301
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
83
01
00
PROACTIVE COMMAND: PLAY TONE 4.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.3.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
32
20
20
8E
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.3.
27.22.4.5.4.4
PLAY TONE (Support of Text Attribute - Large Font Size)
27.22.4.5.4.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.4.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
27.22.4.5.4.4.3
Test purpose
To verify that the Terminal displays the text formatted according to the large font size text attribute configuration
contained in the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.5.4.4.4
Method of test
27.22.4.5.4.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
302
27.22.4.5.4.4.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 4.4 (PLAY TONE, Text Attribute - Large Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.4.1
Message shall be formatted with large font
Terminal → USER Display 'Text Attribute 1'
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.4.2
Message shall be formatted with normal font
Terminal → USER Display 'Text Attribute 2'
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.4.1
Message shall be formatted with large font
Terminal → USER Display 'Text Attribute 1'
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.4.3
Message shall be formatted with normal font
Terminal → USER Display 'Text Attribute 3'
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
Release 10
303
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 4.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
04
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
PROACTIVE COMMAND: PLAY TONE 4.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
ETSI
02
82
81
Release 10
304
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
32
00
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
PROACTIVE COMMAND: PLAY TONE 4.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 3"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.4.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
33
20
20
8E
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.4.
27.22.4.5.4.5
PLAY TONE (Support of Text Attribute - Small Font Size)
27.22.4.5.4.5.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.5.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
ETSI
85
62
01
Release 10
305
27.22.4.5.4.5.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text formatted according to the small font size text attribute configuration
contained in the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.5.4.5.4
Method of test
27.22.4.5.4.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.5.4.2
Procedure
Expected Sequence 4.5 (PLAY TONE, Text Attribute - Small Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.5.1
Message shall be formatted with small font
Terminal → USER Display "Text Attribute 1"
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.5.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.5.2
Message shall be formatted with normal font
Terminal → USER Display 'Text Attribute 2'
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.5.1
Message shall be formatted with small font
Terminal → USER Display "Text Attribute 1"
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.5.3
Terminal → UICC FETCH
ETSI
Release 10
Step
21
22
23
24
306
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.5.3
Message shall be formatted with normal font
Terminal → USER Display 'Text Attribute 3'
size.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: PLAY TONE 4.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
08
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
ETSI
02
82
81
Release 10
307
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 4.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
32
00
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
PROACTIVE COMMAND: PLAY TONE 4.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 3"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.5.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
33
20
20
8E
00
41
01
82
74
11
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.5.
ETSI
02
74
84
81
72
02
03
69
01
85
62
01
Release 10
308
27.22.4.5.4.6
PLAY TONE (Support of Text Attribute - Bold On)
27.22.4.5.4.6.1
Definition and applicability
ETSI TS 102 384 V10.3.0 (2015-08)
See clause 3.2.2.
27.22.4.5.4.6.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
27.22.4.5.4.6.3
Test purpose
To verify that the Terminal displays the text formatted according to the bold text attribute configuration contained in the
PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL RESPONSE command
sent to the UICC.
27.22.4.5.4.6.4
Method of test
27.22.4.5.4.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.6.4.2
Procedure
Expected Sequence 4.6 (PLAY TONE, Text Attribute - Bold On)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.6.1
Message shall be formatted with bold on.
Terminal → USER Display 'Text Attribute 1'
5
Terminal → UICC
6
UICC → Terminal
7
UICC → Terminal
8
9
Terminal → UICC
UICC → Terminal
10
Terminal → USER
11
Terminal → UICC
12
UICC → Terminal
13
UICC → Terminal
14
15
Terminal → UICC
UICC → Terminal
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.6.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.6.2
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.6.2
Display 'Text Attribute 2'
Message shall be formatted with bold off.
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.6.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.6.1
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.6.1
ETSI
Release 10
Step
16
309
Direction
Message/Action
Terminal → USER Display 'Text Attribute 1'
17
Terminal → UICC
18
UICC → Terminal
19
UICC → Terminal
20
21
Terminal → UICC
UICC → Terminal
22
Terminal → USER
23
24
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Message shall be formatted with bold on.
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.6.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.6.3
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.6.3
Display 'Text Attribute 3'
Message shall be formatted with bold off.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 4.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Command performed successfully.
PROACTIVE COMMAND: PLAY TONE 4.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
0E
01
74
31
10
20
20
8E
B4
TERMINAL RESPONSE: PLAY TONE 4.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
ETSI
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Release 10
310
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
83
01
00
PROACTIVE COMMAND: PLAY TONE 4.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
32
00
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
PROACTIVE COMMAND: PLAY TONE 4.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 3"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
ETSI
Release 10
311
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
27.22.4.5.4.6.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
33
20
20
8E
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.6.
27.22.4.5.4.7
PLAY TONE (Support of Text Attribute - Italic On)
27.22.4.5.4.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.7.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
27.22.4.5.4.7.3
Test purpose
To verify that the Terminal displays the text formatted according to the italic text attribute configuration contained in
the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL RESPONSE
command sent to the UICC.
27.22.4.5.4.7.4
Method of test
27.22.4.5.4.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.7.4.2
Procedure
Expected Sequence 4.7 (PLAY TONE, Text Attribute - Italic On)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.7.1
Message shall be formatted with italic on.
Terminal → USER Display 'Text Attribute 1'
5
Terminal → UICC
6
UICC → Terminal
7
UICC → Terminal
8
9
Terminal → UICC
UICC → Terminal
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.7.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.7.2
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.7.2
ETSI
Release 10
Step
10
312
Direction
Message/Action
Terminal → USER Display 'Text Attribute 2'
11
Terminal → UICC
12
UICC → Terminal
13
UICC → Terminal
14
15
Terminal → UICC
UICC → Terminal
16
Terminal → USER
17
Terminal → UICC
18
UICC → Terminal
19
UICC → Terminal
20
21
Terminal → UICC
UICC → Terminal
22
Terminal → USER
23
24
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Message shall be formatted with italic off.
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.7.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.7.1
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.7.1
Display 'Text Attribute 1'
Message shall be formatted with italic on.
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.7.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.7.3
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.7.3
Display 'Text Attribute 3'
Message shall be formatted with italic off.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 4.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Command performed successfully.
PROACTIVE COMMAND: PLAY TONE 4.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
14
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
313
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
0E
01
74
31
20
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
PROACTIVE COMMAND: PLAY TONE 4.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Seconds
Time interval:
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
32
00
20
20
8E
B4
ETSI
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Release 10
314
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 4.7.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 3"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.7.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
33
20
20
8E
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.7.
27.22.4.5.4.8
PLAY TONE (Support of Text Attribute - Underline On)
27.22.4.5.4.8.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.8.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
27.22.4.5.4.8.3
Test purpose
To verify that the Terminal displays the text formatted according to the underline text attribute configuration contained
in the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL RESPONSE
command sent to the UICC.
27.22.4.5.4.8.4
Method of test
27.22.4.5.4.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
315
27.22.4.5.4.8.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 4.8 (PLAY TONE, Text Attribute - Underline On)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.8.1
Message shall be formatted with underline on.
Terminal → USER Display 'Text Attribute 1'
5
Terminal → UICC
6
UICC → Terminal
7
UICC → Terminal
8
9
Terminal → UICC
UICC → Terminal
10
Terminal → USER
11
Terminal → UICC
12
UICC → Terminal
13
UICC → Terminal
14
15
Terminal → UICC
UICC → Terminal
16
Terminal → USER
17
Terminal → UICC
18
UICC → Terminal
19
UICC → Terminal
20
21
Terminal → UICC
UICC → Terminal
22
Terminal → USER
23
24
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.8.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.8.2
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.8.2
Display 'Text Attribute 2'
Message shall be formatted with underline off.
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.8.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.8.1
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.8.1
Display 'Text Attribute 1'
Message shall be formatted with underline on.
Play a Terminal proprietary
positive acknowledgement tone
TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.8.1
PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND
PENDING: PLAY TONE 4.8.3
FETCH
PROACTIVE COMMAND: PLAY
TONE 4.8.3
Display 'Text Attribute 3'
Message shall be formatted with underline off.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 4.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
Command performed successfully.
Release 10
316
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 4.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
40
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
PROACTIVE COMMAND: PLAY TONE 4.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
ETSI
02
82
81
Release 10
317
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
32
00
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
PROACTIVE COMMAND: PLAY TONE 4.8.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 3"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.8.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
33
20
20
8E
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.8.
27.22.4.5.4.9
PLAY TONE (Support of Text Attribute - Strikethrough On)
27.22.4.5.4.9.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.9.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
ETSI
85
62
01
Release 10
318
27.22.4.5.4.9.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal displays the text formatted according to the strikethrough text attribute configuration
contained in the PLAY TONE proactive UICC command, and returns a successful response in the TERMINAL
RESPONSE command sent to the UICC.
27.22.4.5.4.9.4
Method of test
27.22.4.5.4.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.9.4.2
Procedure
Expected Sequence 4.9 (PLAY TONE, Text Attribute - Strikethrough On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.9.1
Message shall be formatted with strikethrough
Terminal → USER Display 'Text Attribute 1'
on.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.9.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.9.2
Message shall be formatted with strikethrough
Terminal → USER Display 'Text Attribute 2'
off.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.9.1
Message shall be formatted with strikethrough
Terminal → USER Display 'Text Attribute 1'
on.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.9.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.9.3
ETSI
Release 10
Step
22
23
24
319
Direction
Message/Action
Terminal → USER Display 'Text Attribute 3'
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Message shall be formatted with strikethrough
off.
Play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 4.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Command performed successfully.
PROACTIVE COMMAND: PLAY TONE 4.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
80
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
ETSI
02
82
81
Release 10
320
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 4.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
32
00
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
PROACTIVE COMMAND: PLAY TONE 4.9.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 3"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.9.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
33
20
20
8E
00
41
01
82
74
11
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.9.
ETSI
02
74
84
81
72
02
03
69
01
85
62
01
Release 10
321
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4.5.4.10
PLAY TONE (Support of Text Attribute - Foreground and Background Colour)
27.22.4.5.4.10.1
Definition and applicability
See clause 3.2.2.
27.22.4.5.4.10.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.5, 6.6.5, 5.2, 8.6, 8.7, 8.2, 8.16, 8.8, 8.31 and 8.70.
27.22.4.5.4.10.3
Test purpose
To verify that the Terminal displays the text formatted according to the foreground and background colour text attribute
configuration contained in the PLAY TONE proactive UICC command, and returns a successful response in the
TERMINAL RESPONSE command sent to the UICC.
27.22.4.5.4.10.4
Method of test
27.22.4.5.4.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.5.4.10.4.2
Procedure
Expected Sequence 4.10 (PLAY TONE, Text Attribute - Foreground and Background Colour)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.10.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.10.1
Message shall be formatted according to the
Terminal → USER Display 'Text Attribute 1'
foreground and background colour text
Play a Terminal proprietary
attribute configuration.
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.10.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 4.10.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 4.10.2
Message shall be formatted with the
Terminal → USER Display 'Text Attribute 2'
Terminal's default foreground and background
Play a Terminal proprietary
colour.
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 4.10.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
Release 10
322
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 4.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha Identifier
Tone:
UICC
Earpiece
"Text Attribute 1"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
75
D0
28
54
74
04
81
65
65
00
03
78
20
10
01
74
31
00
20
20
8E
B4
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 4.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
PROACTIVE COMMAND: PLAY TONE 4.10.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
UICC
ETSI
02
82
81
Release 10
323
Destination device:
Alpha Identifier
Tone:
ETSI TS 102 384 V10.3.0 (2015-08)
Earpiece
"Text Attribute 2"
Terminal proprietary tones: positive acknowledgement tone
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
27.22.4.5.4.10.5
D0
10
75
22
54
74
81
65
65
03
78
20
01
74
32
20
20
8E
00
41
01
82
74
11
02
74
84
81
72
02
03
69
01
85
62
01
Test Requirement
The Terminal shall operate in the manner defined in expected sequences 4.10.
27.22.4.5.5
27.22.4.5.5.1
PLAY TONE (UCS2 display in Chinese)
Definition and applicability
See clause 3.2.2.
27.22.4.5.5.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.2, 8.16 and 8.8.
Additionally the Terminal shall support the UCS2 facility for the coding of the Chinese character, as defined in
ISO/IEC 10646 [2].
27.22.4.5.5.3
Test purpose
To verify that the Terminal displays the text contained in the PLAY TONE proactive UICC command, and returns a
successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that the Terminal plays the requested audio tone through the earpiece.
27.22.4.5.5.4
Method of test
27.22.4.5.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
324
27.22.4.5.5.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 5.1 (PLAY TONE, character set from UCS2 alphabet in Chinese, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY UCS2 alphabet.
TONE 5.1.1
'Middle 1" in Chinese, 0x80 coding of UCS2
Terminal → USER Display "
"
format.
and play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 5.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 5.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY UCS2 alphabet.
TONE 5.1.2
'Middle 1" in Chinese, 0x81 coding of UCS2
Terminal → USER Display "
"
format.
and play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 5.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 5.1.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY UCS2 alphabet.
TONE 5.1.3
'Middle 1" in Chinese, 0x82 coding of UCS2
Terminal → USER Display "
"
format.
and play a Terminal proprietary
positive acknowledgement tone
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 5.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
中一
中一
中一
PROACTIVE COMMAND: PLAY TONE 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
UICC
Earpiece
Alpha Identifier
Tone:
Duration
Time unit:
Time interval:
中一
"
"
Terminal proprietary tones: positive acknowledgement tone
Seconds
1
ETSI
Release 10
325
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
05
01
17
80
81
4E
03
2D
01
4E
20
00
00
8E
82
01
02
11
81
84
03
02
85
01
PROACTIVE COMMAND: PLAY TONE 5.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
UICC
Earpiece
中一
"
"
Terminal proprietary tones: positive acknowledgement tone
Alpha Identifier
Tone:
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
05
01
17
81
81
02
03
9C
01
AD
20
80
00
8E
82
01
02
11
81
84
03
02
85
01
PROACTIVE COMMAND: PLAY TONE 5.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
UICC
Earpiece
中一
"
"
Terminal proprietary tones: positive acknowledgement tone
Alpha Identifier
Tone:
Duration
Time unit:
Time interval:
Seconds
1
Coding:
BER-TLV:
D0
06
01
18
82
01
81
02
03
4E
01
00
20
AD
ETSI
00
80
82
8E
02
01
81
11
03
84
85
02
Release 10
326
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: PLAY TONE 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.5.5.5
81
03
01
20
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 5.1.
27.22.4.5.6
27.22.4.5.6.1
PLAY TONE (UCS2 display in Katakana)
Definition and applicability
See clause 3.2.2.
27.22.4.5.6.2
Conformance requirement
The Terminal shall support the PLAY TONE command as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.3, 6.6.3, 6.8, 6.11, 8.6, 8.7, 8.2, 8.16 and 8.8.
Additionally the Terminal shall support the UCS2 facility for the coding of the Katakana character, as defined in
ISO/IEC 10646 [2].
27.22.4.5.6.3
Test purpose
To verify that the Terminal displays the text contained in the PLAY TONE proactive UICC command, and returns a
successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that the Terminal plays the requested audio tone through the earpiece.
27.22.4.5.6.4
Method of test
27.22.4.5.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
327
27.22.4.5.6.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 6.1 (PLAY TONE, with UCS2 in Katakana, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY UCS2 alphabet.
TONE 6.1.1
Characters in Katakana, 0x80 coding of UCS2
Terminal → USER Display "80 0"
format.
Play a Terminal standard
supervisory dial tone for 5
seconds
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 6.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 6.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 6.1.2
Characters in Katakana, 0x81 coding of UCS2
Terminal → USER Display "81 1"
format.
Play a Terminal standard
supervisory dial tone for 5
seconds
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 6.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 6.1.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 6.1.3
Characters in Katakana, 0x82 coding of UCS2
Terminal → USER Display "82 2"
format.
Play a Terminal standard
supervisory dial tone for 5
seconds
Terminal → UICC TERMINAL RESPONSE: PLAY Command performed successfully.
TONE 6.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ル
ル
ル
PROACTIVE COMMAND: PLAY TONE 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
UICC
Earpiece
Alpha Identifier
Tone:
Duration
Time unit:
Time interval:
ル
"80 0"
Terminal proprietary tones: Standard supervisory tones: Dial tone
Seconds
5
ETSI
Release 10
328
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
09
01
1B
80
84
81
00
02
03
38
01
01
00
05
20
30
00
30
82
EB
02
00
81
30
03
8E
85
01
PROACTIVE COMMAND: PLAY TONE 6.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
UICC
Earpiece
ル
"81 1"
Terminal proprietary tones: Standard supervisory tones: Dial tone
Alpha Identifier
Tone:
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
07
02
19
81
01
81
04
05
03
61
01
38
20
31
00
EB
82
31
02
8E
81
01
03
01
85
84
PROACTIVE COMMAND: PLAY TONE 6.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
UICC
Earpiece
ル
"82 2"
Terminal proprietary tones: Standard supervisory tones: Dial tone
Alpha Identifier
Tone:
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
08
84
1A
82
02
81
04
01
03
30
05
01
A0
20
38
ETSI
00
32
82
CB
02
32
81
8E
03
01
85
01
Release 10
329
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: PLAY TONE 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.5.6.5
81
03
01
20
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.1.
27.22.4.6
27.22.4.6.1
POLL INTERVAL
Definition and applicability
See clause 3.2.2.
27.22.4.6.2
Conformance requirement
The Terminal shall support the POLL INTERVAL command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.6, 6.6.6, 5.2, 8.6, 8.7 and 8.8.
27.22.4.6.3
Test purpose
To verify that the Terminal shall send a TERMINAL RESPONSE (OK) to the UICC after the Terminal receives the
POLL INTERVAL proactive UICC command.
To verify that the Terminal gives a valid response to the polling interval requested by the UICC.
To verify that the Terminal sends STATUS commands to the UICC at an interval no longer than the interval negotiated
by the UICC.
27.22.4.6.4
27.22.4.6.4.1
Method of test
Initial conditions
The Terminal is connected to the UICC Simulator.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
330
27.22.4.6.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 1.1 (POLL INTERVAL, Seconds)
Step
1
2
3
4
5
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND PENDING:
POLL INTERVAL 1.1.1
Terminal → UICC FETCH
Duration: 20 seconds.
UICC → Terminal PROACTIVE COMMAND: POLL
INTERVAL 1.1.1
Command performed successfully,
Terminal → UICC TERMINAL RESPONSE: POLL
INTERVAL 1.1.1
duration depends on the Terminal's
capabilities.
Terminal → UICC Terminal polls in intervals as stated in
the duration TLV of TERMINAL
RESPONSE: POLL INTERVAL 1.1.1
PROACTIVE COMMAND: POLL INTERVAL 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POLL INTERVAL
"00"
Device identities
Source device:
Destination device:
UICC
Terminal
Duration
Time unit:
Time interval:
Seconds
20
Coding:
BER-TLV:
D0
02
0D
01
81
14
03
01
03
00
82
02
81
82
84
83
01
00
TERMINAL RESPONSE: POLL INTERVAL 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POLL INTERVAL
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Duration
Time unit:
Time interval:
Seconds
20
Coding:
BER-TLV:
81
84
03
02
01
01
03
14
00
82
ETSI
02
82
81
Release 10
NOTE:
331
ETSI TS 102 384 V10.3.0 (2015-08)
If the requested poll interval is not supported by the Terminal, the Terminal is allowed to use a different
one as stated in ETSI TS 102 223 [1], clause 6.4.6.
27.22.4.6.5
Test requirement
The Terminal shall operate in the manner defined in expected sequence 1.1.
27.22.4.7
REFRESH
27.22.4.7.1
REFRESH (normal)
27.22.4.7.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.7.1.2
Conformance requirement
The Terminal shall support the REFRESH command as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.7, 6.6.13, 5.2, 8.6, 8.7 and 8.18.
27.22.4.7.1.3
Test purpose
To verify that the Terminal performs the UICC initialization and/or re-reads the contents and structure of the EFs on the
UICC that have been changed and/or restarts the card session by resetting the Terminal, and successfully returns the
result of the execution of the command in the TERMINAL RESPONSE command send to the UICC.
27.22.4.7.1.4
Method of test
27.22.4.7.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.7.1.4.2
Procedure
Expected Sequence 1.1 (REFRESH, NAA Initialization and Full File Change Notification)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.2 (REFRESH, File Change Notification)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC→ Terminal PROACTIVE COMMAND
PENDING: REFRESH 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
REFRESH 1.2.1
UICC
Update EF ICCID
Terminal → UICC TERMINAL RESPONSE:
REFRESH 1.2.1A
Or
TERMINAL RESPONSE:
REFRESH 1.2.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
ETSI
Comments
To inform the Terminal that there is a change
in ICCID value.
New EF ICCID value:
98010000000012345678.
Additional EFs read.
Release 10
332
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: REFRESH 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
REFRESH
File Change Notification
Device identities
Source device:
Destination device:
UICC
Terminal
File List
Number of files:
File:
1
3F002FE2
Coding:
BER-TLV:
D0
05
10
01
81
3F
03
00
01
2F
01
E2
01
82
02
81
82
92
83
01
00
01
03
TERMINAL RESPONSE: REFRESH 1.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
REFRESH
File Change Notification
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
01
01
82
02
82
81
TERMINAL RESPONSE: REFRESH 1.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
REFRESH
File Change Notification
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
REFRESH performed with additional EFs read
Coding:
BER-TLV:
81
03
01
01
01
82
ETSI
02
82
81
83
Release 10
333
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.3 (REFRESH, NAA Initialization and File Change Notification)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.4 (REFRESH, NAA Initialization)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.5 (REFRESH, UICC Reset)
Step
1
Direction
Message/Action
UICC→ Terminal PROACTIVE COMMAND
PENDING: REFRESH 1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
REFRESH 1.5.1
Terminal
Terminal resets the UICC and
perform NAA initialization if any
UICC → Terminal PROACTIVE UICC SESSION
ENDED
2
3
4
5
Comments
PROACTIVE COMMAND: REFRESH 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
REFRESH
UICC Reset
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
01
04
82
02
81
Expected Sequence 1.6 (REFRESH, NAA Application Reset)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.7 (REFRESH, NAA Session Reset)
The test method is not defined in the present document as it depends on a present NAA.
27.22.4.7.1.5
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.7.
27.22.4.8
27.22.4.8.1
27.22.4.8.1.1
SET UP MENU and ENVELOPE MENU SELECTION
SET UP MENU (normal) and ENVELOPE MENU SELECTION
Definition and applicability
See clause 3.2.2.
27.22.4.8.1.2
Conformance requirement
The Terminal shall support the SET UP MENU command as defined in:
•
ETSI TS 102 223 [1], clauses 5, 6.4.8, 6.6.7, 6.8, 6.11, 8.6, 8.7, 8.2, 8.9 and 9.4.
ETSI
82
Release 10
334
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal shall support MENU SELECTION as defined in:
•
ETSI TS 102 223 [1], clauses 4.4, 5.2, 6.4.8, 6.9, 7.2, 8.7 and 8.10.
27.22.4.8.1.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that the Terminal replaces the current list of menu items with the list of menu items contained in the SET UP
MENU command.
To verify that the Terminal removes the current list of menu items following receipt of a SET UP MENU command
with no items.
To verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
To verify that when the help is available for the command and the user gas indicated the need to get help information on
one of the items, the Terminal informs properly the UICC about an HELP REQUEST, using the MENU SELECTION
mechanism.
27.22.4.8.1.4
Method of test
27.22.4.8.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.1.4.2
Procedure
Expected Sequence 1.1 (SET UP MENU and MENU SELECTION, without Help Request, Replace and Remove
a Toolkit Menu)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
Direction
Message/Action
Comments
First Set Up Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 1.1.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" and
"Item 4" under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 1.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3",
"Item 4"
USER → Terminal Select the "Item 2" Menu entry
Terminal → UICC Send the ENVELOPE 1.1.1:
MENU SELECTION
(Identifier of item: 2)
Second Set Up Menu, REPLACE Old Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 1.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 1.1.2
ETSI
Release 10
Step
14
15
16
17
18
19
20
21
22
23
24
25
26
27
335
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → USER Integrate the new menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "One" and "Two" under this
header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 1.1.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "One", "Two"
USER → Terminal Select the "Two" menu entry
Terminal → UICC Send the ENVELOPE 1.1.2:
MENU SELECTION
(Identifier of item: 12)
Third Set Up Menu, REMOVE Toolkit Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 1.1.3
with SW1/SW2 of '91 0F'.
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 1.1.3
Terminal → USER Remove the menu "Toolkit Menu"
from its menu system.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 1.1.3
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Has to unsuccessfully find the
Toolkit Menu
PROACTIVE COMMAND: SET UP MENU 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Identifier of item:
Text string of item:
4
"Item 4"
Item
Item
Item
ETSI
Release 10
336
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0C
75
02
65
34
3B
54
8F
49
6D
81
6F
07
74
20
03
6F
01
65
33
01
6C
49
6D
8F
25
6B
74
20
07
00
69
65
32
04
82
74
6D
8F
49
02
20
20
07
74
81
4D
31
03
65
82
65
8F
49
6D
85
6E
07
74
20
00
69
65
82
74
8F
02
20
04
81
4D
12
82
65
54
85
6E
77
00
82
02
81
82
85
PROACTIVE COMMAND: SET UP MENU 1.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
"11"
"One"
Identifier of item:
Text string of item:
"12"
"Two"
Item
Coding:
BER-TLV:
D0
0C
75
6F
23
54
8F
81
6F
04
03
6F
11
01
6C
4F
25
6B
6E
PROACTIVE COMMAND: SET UP MENU 1.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Item:
UICC
Terminal
Empty
Coding:
BER-TLV:
D0
00
0D
8F
81
00
03
01
25
ETSI
Release 10
337
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP MENU 1.1.1, 1.1.2 and 1.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"no help information available"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
83
01
00
ENVELOPE 1.1.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
02
Coding:
BER-TLV:
D3
07
82
02
01
81
90
01
02
02
01
81
90
01
12
ENVELOPE 1.1.2: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
12
Coding:
BER-TLV:
D3
07
82
Expected Sequence 1.2 (SET UP MENU, Large Menu with many items or with large items or with Large Alpha
Identifier)
Step
1
2
3
Direction
Message/Action
Comments
First Large Menu with many items, Fetch of
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 1.2.1
FF bytes.
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 1.2.1
ETSI
Release 10
Step
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
338
Direction
Message/Action
Terminal → USER Integrate the new menu header of
"LargeMenu1" into its menu
system and have the menu items
of "Zero", "One", "Two", Three",
"Four", "Five", "Six", "Seven",
"Eight", "Nine", "Alpha", "Bravo",
"Charlie", "Delta", "Echo", "Foxtrot", "Black", "Brown", "Red",
"Orange", "Yellow", "Green",
"Blue", "Violet", "Grey", "White",
"milli", "micro", "nano" and "pico"
under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 1.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit "LargeMenu1"
Terminal → USER Display "Zero", "One", "Two" …
"pico"
USER → Terminal Select the "Orange" menu entry
Terminal → UICC Send the ENVELOPE 1.2.1:
MENU SELECTION
(Identifier of item: 0x3D)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 1.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 1.2.2
Terminal → USER Integrate the new menu header of
"LargeMenu2" into its menu
system and have the menu items
of "1 Call Forward Unconditional",
"2 Call Forward On User Busy", "3
Call Forward On No Reply", "4 Call
Forward On User Not Reachable",
"5 Barring Of All Outgoing Calls",
"6 Barring Of All Outgoing Int
Calls" and "7 CLI Presentation"
under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 1.2.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu
"LargeMenu2"
Terminal → USER Display "1 Call Forward
Unconditional", "2 Call Forward On
User Busy", "3 Call Forward On No
Reply", "4 Call Forward On User
Not Reachable", "5 Barring Of All
Outgoing Calls", "6 Barring Of All
Outgoing Int Calls", "7 CLI
Presentation"
USER → Terminal Select the "5 Barring Of All
Outgoing Calls" menu entry
Terminal → UICC Send the ENVELOPE 1.2.2:
MENU SELECTION
(Identifier of item: 0xFB)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 1.2.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 1.2.3
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Second Large Menu with large items, Fetch of
F6 bytes.
Command Performed Successfully.
Third Large Menu with a Large Alpha
Identifier and only one Short Item, Fetch of FF
bytes.
Release 10
Step
24
25
26
27
28
29
30
339
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → USER Integrate the new menu header of
"The SIM shall supply a set of
menu items, which shall be
integrated with the menu system
(or other MMI facility) in order to
give the user the opportunity to
choose one of these menu items at
his own discretion. Each item
comprises a sh" into it's menu
system and have a menu item of
"Y" under this header".
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 1.2.3
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "The SIM
shall supply a set of menu items,
which shall be integrated with the
menu system (or other MMI
facility) in order to give the user the
opportunity to choose one of these
menu items at his own discretion.
Each item comprises a sh".
Terminal → USER Display "Y"
USER → Terminal Select the item "Y"
Terminal → UICC Send the ENVELOPE 1.2.3:
MENU SELECTION
(Identifier of item: 1)
PROACTIVE COMMAND: SET UP MENU 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
UICC
Terminal
"LargeMenu1"
Item
Identifier of item:
Text string of item:
"50"
"Zero"
Identifier of item:
Text string of item:
"4F"
"One"
Identifier of item:
Text string of item:
"4E"
"Two"
Identifier of item:
Text string of item:
"4D"
"Three"
Identifier of item:
Text string of item:
"4C"
"Four"
Identifier of item:
Text string of item:
"4B"
"Five"
Item
Item
Item
Item
Item
ETSI
Release 10
340
Item
Identifier of item:
Text string of item:
"4A"
"Six"
Identifier of item:
Text string of item:
"49"
"Seven"
Identifier of item:
Text string of item:
"48"
"Eight"
Identifier of item:
Text string of item:
"47"
"Nine"
Identifier of item:
Text string of item:
"46"
"Alpha"
Identifier of item:
Text string of item:
"45"
"Bravo"
Identifier of item:
Text string of item:
"44"
"Charlie"
Identifier of item:
Text string of item:
"43"
"Delta"
Identifier of item:
Text string of item:
"42"
"Echo"
Identifier of item:
Text string of item:
"41"
"Fox-trot"
Identifier of item:
Text string of item:
"40"
"Black"
Identifier of item:
Text string of item:
"3F"
"Brown"
Identifier of item:
Text string of item:
"3E"
"Red"
Identifier of item:
Text string of item:
"3D"
"Orange"
Identifier of item:
Text string of item:
"3C"
"Yellow"
Identifier of item:
Text string of item:
"3B"
"Green"
Identifier of item:
Text string of item:
"3A"
"Blue"
Identifier of item:
Text string of item:
"39"
"Violet"
Identifier of item:
Text string of item:
"38"
"Grey"
Identifier of item:
Text string of item:
"37"
"White"
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Release 10
341
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
"36"
"milli"
Identifier of item:
Text string of item:
"35"
"micro"
Identifier of item:
Text string of item:
"34"
"nano"
Identifier of item:
Text string of item:
"33"
"pico"
Item
Item
Item
Coding:
BER-TLV:
D0
85
8F
65
72
4B
06
67
46
76
8F
63
6F
3F
8F
59
65
56
79
6D
6F
69
81
0A
05
8F
65
46
49
68
41
6F
06
68
74
42
07
65
6E
69
8F
69
8F
63
FC
4C
50
04
65
69
53
74
6C
8F
43
6F
8F
72
3D
6C
8F
6F
06
6C
05
6F
81
61
5A
4E
8F
76
65
8F
70
08
44
8F
06
6F
4F
6C
05
6C
37
6C
34
03
72
65
54
05
65
76
05
68
44
65
09
40
77
72
6F
3A
65
57
69
6E
01
67
72
77
4C
8F
65
47
61
43
6C
41
42
6E
61
77
42
74
68
8F
61
25
65
6F
6F
46
04
6E
4E
8F
68
74
46
6C
8F
6E
8F
6C
8F
69
06
6E
00
4D
8F
8F
6F
4A
8F
69
06
61
61
6F
61
04
67
06
75
05
74
35
6F
PROACTIVE COMMAND: SET UP MENU 1.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha Identifier:
UICC
Terminal
"LargeMenu2"
Item
Identifier of item:
Text string of item:
"FF"
"1 Call Forward Unconditional"
Identifier of item:
Text string of item:
"FE"
"2 Call Forward On User Busy"
Identifier of item:
Text string of item:
"FD"
"3 Call Forward On No Reply"
Item
Item
ETSI
82
65
04
06
75
53
06
6E
45
72
8F
78
63
3E
65
3B
65
38
65
6D
8F
02
6E
4F
4D
72
69
48
65
42
6C
05
2D
6B
52
8F
47
8F
47
8F
69
05
81
75
4F
54
8F
78
45
8F
72
69
42
74
8F
65
07
72
07
72
06
63
33
82
31
6E
68
05
8F
69
06
61
65
45
72
06
64
3C
65
39
65
36
72
70
Release 10
342
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
"FC"
"4 Call Forward On User Not Reachable"
Identifier of item:
Text string of item:
"FB"
"5 Barring Of All Outgoing Calls"
Identifier of item:
Text string of item:
"FA"
"6 Barring Of All Outgoing Int Calls"
Identifier of item:
Text string of item:
"F9"
"7 CLI Presentation"
Item
Item
Item
Coding:
BER-TLV:
D0
85
8F
72
69
43
20
79
6F
20
61
4F
52
35
20
67
42
6C
49
37
74
81
0A
1D
77
74
61
4F
8F
72
52
6C
6E
65
20
41
20
61
6C
6E
20
61
F3
4C
FF
61
69
6C
6E
1B
77
65
6C
20
61
42
6C
43
72
20
74
43
74
81
61
31
72
6F
6C
20
FD
61
70
20
55
63
61
6C
61
72
4F
20
4C
69
03
72
20
64
6E
20
55
33
72
6C
46
73
68
72
20
6C
69
75
43
49
6F
01
67
43
20
61
46
73
20
64
79
6F
65
61
72
4F
6C
6E
74
61
20
6E
25
65
61
55
6C
6F
65
43
20
8F
72
72
62
69
75
73
67
67
6C
50
00
4D
6C
6E
8F
72
72
61
4F
25
77
20
6C
6E
74
8F
20
6F
6C
72
82
65
6C
63
1C
77
20
6C
6E
FC
61
4E
65
67
67
24
4F
69
73
65
02
6E
20
6F
FE
61
42
6C
20
34
72
6F
8F
20
6F
FA
66
6E
8F
73
81
75
46
6E
32
72
75
20
4E
20
64
74
20
4F
69
36
20
67
13
65
82
32
6F
64
20
64
73
46
6F
43
20
20
FB
66
6E
20
41
20
F9
6E
PROACTIVE COMMAND: SET UP MENU 1.2.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
Alpha Identifier:
1
SET UP MENU
"00"
UICC
Terminal
"The SIM shall supply a set of menu items, which shall be integrated
with the menu system (or other MMI facility) in order to give the user
the opportunity to choose one of these menu items at his own
discretion. Each item comprises a sh"
Item
Identifier of item:
Text string of item:
"01"
"Y"
ETSI
Release 10
343
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
85
68
61
75
63
69
69
20
6F
63
72
20
65
79
6F
20
61
69
61
70
02
81
81
61
20
20
68
6E
74
73
74
69
64
74
20
20
6E
6D
74
73
63
72
01
FC
EC
6C
73
69
20
74
68
79
68
6C
65
68
6F
74
65
65
20
63
68
69
59
81
54
6C
65
74
73
65
20
73
65
69
72
65
70
6F
20
6E
68
72
20
73
03
68
20
74
65
68
67
74
74
72
74
20
20
70
20
6F
75
69
65
69
65
01
65
73
20
6D
61
72
68
65
20
79
74
75
6F
63
66
20
73
74
74
73
25
20
75
6F
73
6C
61
65
6D
4D
29
6F
73
72
68
20
69
20
69
65
20
00
53
70
66
2C
6C
74
20
20
4D
20
20
65
74
6F
74
74
6F
6F
6D
61
82
49
70
20
20
20
65
6D
28
49
69
67
72
75
6F
68
65
77
6E
20
20
02
4D
6C
6D
77
62
64
65
6F
20
6E
69
20
6E
73
65
6D
6E
2E
63
73
81
20
79
65
68
65
20
6E
72
66
20
76
74
69
65
73
73
20
20
6F
68
82
73
20
6E
69
20
77
75
20
61
6F
65
68
74
20
65
20
64
45
6D
8F
83
01
00
TERMINAL RESPONSE: SET UP MENU 1.2.1, 1.2.2 and 1.2.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"no help information available"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
ENVELOPE 1.2.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
3D
Coding:
BER-TLV:
D3
07
82
02
ETSI
01
81
90
01
3D
Release 10
344
ETSI TS 102 384 V10.3.0 (2015-08)
ENVELOPE 1.2.2: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
FB
Coding:
BER-TLV:
D3
07
82
02
01
81
90
01
FB
02
01
81
90
01
01
ENVELOPE 1.2.3: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
01
Coding:
BER-TLV:
D3
07
82
The following table details the test requirements with relation to the tested features:
Proactive UICC
Command Number
1.1.1
1.1.2
1.1.3
1.2.1
1.2.2
1.2.3
27.22.4.8.1.5
Proactive UICC Command Facilities
Alpha Identifier
Number of Maximum length
Length
items
of item
12
4
6
12
2
3
10
0
10
30
8
10
7
37
235
1
1
Test requirement
The Terminal shall operate in the manner defined in expected sequence 1.1 and in expected sequence 1.2.
27.22.4.8.2
27.22.4.8.2.1
SET UP MENU (help request support) and ENVELOPE MENU SELECTION
Definition and applicability
See clause 3.2.2.
27.22.4.8.2.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clause 8.21.
27.22.4.8.2.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that when the help is available for the command and the user has indicated the need to get help information on
one of the items, the Terminal informs properly the UICC about an HELP REQUEST, using the MENU SELECTION
mechanism.
ETSI
Release 10
345
ETSI TS 102 384 V10.3.0 (2015-08)
To verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.2.4
Method of test
27.22.4.8.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.2.4.2
Procedure
Expected Sequence 2.1 (SET UP MENU and MENU SELECTION, with Help Request, Replace and Remove a
Toolkit Menu)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
Comments
First Set Up Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 2.1.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" and
"Item 4" under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 2.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3",
"Item 4"
USER → Terminal Select the Help Request on
"Item 2" Menu entry
Terminal → UICC Send the ENVELOPE 2.1.1:
MENU SELECTION
(Identifier of item: 2)
PROACTIVE COMMAND: SET UP MENU 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"80"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Item
ETSI
Release 10
346
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
3
"Item 3"
Identifier of item:
Text string of item:
4
"Item 4"
Item
Coding:
BER-TLV:
D0
0C
75
02
65
34
3B
54
8F
49
6D
81
6F
07
74
20
03
6F
01
65
33
01
6C
49
6D
8F
25
6B
74
20
07
80
69
65
32
04
82
74
6D
8F
49
02
20
20
07
74
81
4D
31
03
65
82
65
8F
49
6D
85
6E
07
74
20
83
01
00
TERMINAL RESPONSE: SET UP MENU 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"help information available"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
80
82
02
82
81
ENVELOPE 2.1.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Help request tag
Keypad
UICC
02
Coding:
BER-TLV:
27.22.4.8.2.5
D3
09
82
02
01
81
90
01
02
15
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.8.3
27.22.4.8.3.1
SET UP MENU (next action support) and ENVELOPE MENU SELECTION
Definition and applicability
See clause 3.2.2.
If the UICC provides an Items Next Action Indicator data object, the comprehension required flag shall be set to '0'.
ETSI
Release 10
347
27.22.4.8.3.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clause 8.24.
27.22.4.8.3.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that the next action indicator is supported.
To verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.3.4
Method of test
27.22.4.8.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.3.4.2
Procedure
Expected Sequence 3.1 (SET UP MENU, next action indicator "Send SM", "Set Up Call", "Launch Browser",
"Provide Local Information", successful)
Step
1
2
3
4
5
6
7
8
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 3.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 3.1.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" and
"Item 4" under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 3.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3",
"Item 4"
9
USER → Terminal Navigate in the items, then select
"Item 2".
10
Terminal → UICC Send the ENVELOPE 3.1.1:
MENU SELECTION
(Identifier of item: 2)
ETSI
Comments
First Set Up Menu.
Command Performed Successfully.
The Terminal may indicate to the user the
consequences of performing the selection of
an item.
The Terminal may indicate to the user the
consequences of performing the selection of
an item.
Release 10
348
ETSI TS 102 384 V10.3.0 (2015-08)
ENVELOPE 3.1.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
02
Coding:
BER-TLV:
D3
07
82
02
01
81
90
01
02
PROACTIVE COMMAND: SET UP MENU 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Item
Identifier of item:
Text string of item:
Items next action indicator list
List:
4
"Item 4"
"Send SM", "Set Up Call", "Launch Browser", "Provide Local
Information"
Coding:
BER-TLV:
D0
0C
75
02
65
34
41
54
8F
49
6D
18
81
6F
07
74
20
04
03
6F
01
65
33
13
01
6C
49
6D
8F
10
25
6B
74
20
07
15
00
69
65
32
04
26
82
74
6D
8F
49
TERMINAL RESPONSE: SET UP MENU 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"no help information available"
ETSI
02
20
20
07
74
81
4D
31
03
65
82
65
8F
49
6D
85
6E
07
74
20
Release 10
349
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.3.5
81
03
01
25
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 3.1.
27.22.4.8.4
SET UP MENU (display of icons) and ENVELOPE MENU SELECTION
27.22.4.8.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.4.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.31 and 8.32.
27.22.4.8.4.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that icons are displayed with the command Set Up Menu in the Alpha Identifier and Items Data Objects. To
verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.4.4
Method of test
27.22.4.8.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.4.4.2
Procedure
Expected Sequence 4.1A (SET UP MENU, BASIC ICON NOT SELF EXPLANATORY in ALPHA ID and
ITEMS DATA OBJECTS, successful)
Step
1
2
3
4
5
Direction
Message/Action
Comments
First Set Up Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 4.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 4.1.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 4.1.1A
ETSI
Release 10
Step
6
7
8
9
10
350
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Verify the icon is displayed with alpha id.
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3".
USER → Terminal Navigate in the items, then select Verify icons are displayed for each item.
"Item 2".
Terminal → UICC Send the ENVELOPE 3.1.1:
MENU SELECTION
(Identifier of item: 2)
PROACTIVE COMMAND: SET UP MENU 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Icon identifier
Icon qualifier:
Icon identifier:
icon is not self explanatory
record 1 EF (IMG)
Item icon identifier list
Icon qualifier:
Icon identifier list:
icon is not self explanatory
record 5 EF (IMG), record 5 EF (IMG), record 5 EF (IMG)
Coding:
BER-TLV:
D0
0C
75
02
65
05
3C
54
8F
49
6D
05
81
6F
07
74
20
03
6F
01
65
33
01
6C
49
6D
9E
25
6B
74
20
02
00
69
65
32
01
82
74
6D
8F
01
TERMINAL RESPONSE: SET UP MENU 4.1.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"no help information available"
Device identities
ETSI
02
20
20
07
9F
81
4D
31
03
04
82
65
8F
49
01
85
6E
07
74
05
Release 10
351
ETSI TS 102 384 V10.3.0 (2015-08)
Source device:
Destination device:
Terminal
UICC
General Result:
Command performed successfully
Result
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
83
01
00
Expected Sequence 4.1B (SET UP MENU, BASIC ICON NOT SELF EXPLANATORY in ALPHA ID and
ITEMS DATA OBJECTS, requested icon could not be displayed)
Step
1
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 4.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 4.1.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 4.1.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header "Toolkit Menu".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 3.1.1:
MENU SELECTION
(Identifier of item: 2)
2
3
4
5
6
7
8
9
10
Comments
First Set Up Menu.
Command performed successfully, but
requested icon could not be displayed.
Verify that either for the header or for each of
the items no icon is displayed.
TERMINAL RESPONSE: SET UP MENU 4.1.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"no help information available"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
25
00
82
ETSI
02
82
81
83
01
04
Release 10
352
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 4.2A (SET UP MENU, BASIC ICON SELF EXPLANATORY in ALPHA ID and ITEMS
DATA OBJECTS, successful)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 4.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 4.2.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 4.2.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 3.1.1:
MENU SELECTION
(Identifier of item: 2)
Comments
First Set Up Menu.
Command Performed Successfully.
Verify the icon is displayed in alpha id.
Verify icons are displayed for each item.
PROACTIVE COMMAND: SET UP MENU 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Icon identifier
Icon qualifier:
Icon identifier:
icon is self explanatory
record 1 EF (IMG)
Item icon identifier list
Icon qualifier:
Icon identifier list:
icon is self explanatory
record 5 EF (IMG), record 5 EF (IMG), record 5 EF (IMG)
ETSI
Release 10
353
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0C
75
02
65
05
3C
54
8F
49
6D
05
81
6F
07
74
20
03
6F
01
65
33
01
6C
49
6D
9E
25
6B
74
20
02
00
69
65
32
00
82
74
6D
8F
01
02
20
20
07
9F
81
4D
31
03
04
82
65
8F
49
00
85
6E
07
74
05
82
81
83
01
00
TERMINAL RESPONSE: SET UP MENU 4.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"no help information available"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
Expected Sequence 4.2B (SET UP MENU, BASIC ICON SELF EXPLANATORY in ALPHA ID and ITEMS
DATA OBJECTS, requested icon could not be displayed)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
Comments
First Set Up Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 4.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 4.2.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 4.2.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3" Verify that either for the header or for each of
under the header of "Toolkit
the items no icon is displayed.
Menu".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 3.1.1:
MENU SELECTION
(Identifier of item: 2)
ETSI
Release 10
354
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP MENU 4.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"no help information available"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Coding:
BER-TLV:
27.22.4.8.4.5
81
03
01
25
00
82
02
82
81
83
01
04
Test requirement
The Terminal shall operate in the manner defined in expected sequences 4.1A to 4.2B.
27.22.4.8.5
27.22.4.8.5.1
SET UP MENU (soft keys support) and ENVELOPE MENU SELECTION
Definition and applicability
See clause 3.2.2.
27.22.4.8.5.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1.
27.22.4.8.5.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that if soft key preferred is indicated in the command details and soft key for SET UP MENU is supported by
the Terminal and the number of icon items does not exceed the number of soft keys available, then the Terminal
displays those icons as soft key.
To verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.5.4
Method of test
27.22.4.8.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
355
27.22.4.8.5.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 5.1 (SET UP MENU, SOFT KEY PREFERRED, successful)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
Comments
First Set Up Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 5.1.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2" under this
header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 5.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2"
USER → Terminal Navigate in the items, then select Verify we can select items through soft keys.
"Item 2".
Terminal → UICC Send the ENVELOPE 3.1.1:
MENU SELECTION
(Identifier of item: 2)
PROACTIVE COMMAND: SET UP MENU 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
'01' (selection using soft key preferred)
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Item
Coding:
BER-TLV:
D0
0C
75
02
29
54
8F
49
81
6F
07
74
03
6F
01
65
01
6C
49
6D
25
6B
74
20
ETSI
01
69
65
32
82
74
6D
02
20
20
81
4D
31
82
65
8F
85
6E
07
Release 10
356
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP MENU 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
'01' (selection using soft key preferred)
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.5.5
81
03
01
25
01
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 5.1.
27.22.4.8.6
SET UP MENU (support of Text Attribute) and ENVELOPE MENU SELECTION
27.22.4.8.6.1
SET UP MENU (support of Text Attribute - Left Alignment) and ENVELOPE MENU
SELECTION
27.22.4.8.6.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.1.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.1.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the left alignment text attribute configuration within the command Set Up
Menu and the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.6.1.4
Method of test
27.22.4.8.6.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
357
27.22.4.8.6.1.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 6.1 (SET UP MENU, Text Attribute - Left Alignment, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.1.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.1.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
PROACTIVE COMMAND: SET UP MENU 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
ETSI
Comments
Command Performed Successfully.
Verify text attribute of the alpha identifier and
of each item are displayed with left alignment.
Command Performed Successfully.
Verify text attribute of the alpha identifier and
of each item are displayed without left
alignment.
Remark: If left alignment is the Terminal's
default alignment as declared in table A.2/9,
no alignment change will take place.
Release 10
358
Device identities
Source device:
Destination device:
Alpha identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
14
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
00
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
00
25
6B
01
65
33
B4
TERMINAL RESPONSE: SET UP MENU 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
ETSI
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
00
81
4D
6D
8F
0E
B4
82
65
20
07
00
00
85
6E
31
03
B4
06
Release 10
359
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
83
01
00
00
69
49
6D
82
74
74
20
02
20
65
35
81
4D
6D
8F
82
65
20
07
85
6E
34
06
PROACTIVE COMMAND: SET UP MENU 6.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 2"
Item
Identifier of item:
Text string of item:
4
"Item 4"
Identifier of item:
Text string of item:
5
"Item 5"
Identifier of item:
Text string of item:
6
"Item 6"
Item
Item
Coding:
BER-TLV:
D0
0E
75
8F
49
34
54
20
07
74
81
6F
32
05
65
03
6F
8F
49
6D
01
6C
07
74
20
25
6B
04
65
36
ENVELOPE 6.1.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
02
Coding:
BER-TLV:
D3
07
82
02
01
ETSI
81
90
01
02
Release 10
360
ETSI TS 102 384 V10.3.0 (2015-08)
ENVELOPE 6.1.2: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
05
Coding:
BER-TLV:
27.22.4.8.6.1.5
D3
07
82
02
01
81
90
01
05
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.1.
27.22.4.8.6.2
SET UP MENU (support of Text Attribute - Center Alignment) and ENVELOPE MENU
SELECTION
27.22.4.8.6.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.2.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.2.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the center alignment text attribute configuration within the command Set
Up Menu and the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.6.2.4
Method of test
27.22.4.8.6.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.2.4.2
Procedure
Expected Sequence 6.2 (SET UP MENU, Text Attribute - Center Alignment, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.2.1
ETSI
Comments
Release 10
Step
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
361
Direction
Message/Action
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.2.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
PROACTIVE COMMAND: SET UP MENU 6.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Verify text attribute of the alpha identifier and
of each item are displayed with center
alignment.
Command Performed Successfully.
Verify text attribute of the alpha identifier and
of each item are displayed without center
alignment.
Remark: If center alignment is the Terminal's
default alignment as declared in table A.2/9,
no alignment change will take place.
Release 10
362
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
14
Centre Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Centre Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Centre Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Centre Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
01
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
01
25
6B
01
65
33
B4
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
01
TERMINAL RESPONSE: SET UP MENU 6.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
81
4D
6D
8F
0E
B4
82
65
20
07
01
00
85
6E
31
03
B4
06
Release 10
363
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
83
01
00
00
69
49
6D
82
74
74
20
02
20
65
35
81
4D
6D
8F
82
65
20
07
85
6E
34
06
PROACTIVE COMMAND: SET UP MENU 6.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 2"
Item
Identifier of item:
Text string of item:
4
"Item 4"
Identifier of item:
Text string of item:
5
"Item 5"
Identifier of item:
Text string of item:
6
"Item 6"
Item
Item
Coding:
BER-TLV:
27.22.4.8.6.2.5
D0
0E
75
8F
49
34
54
20
07
74
81
6F
32
05
65
03
6F
8F
49
6D
01
6C
07
74
20
25
6B
04
65
36
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.2.
27.22.4.8.6.3
SET UP MENU (support of Text Attribute - Right Alignment) and ENVELOPE MENU
SELECTION
27.22.4.8.6.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.3.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.3.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the right alignment text attribute configuration within the command Set Up
Menu and the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
ETSI
Release 10
364
27.22.4.8.6.3.4
Method of test
27.22.4.8.6.3.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.3.4.2
Procedure
Expected Sequence 6.3 (SET UP MENU, Text Attribute - Right Alignment, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.3.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.3.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.3.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.3.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
ETSI
Comments
Command Performed Successfully.
Verify text attribute of the alpha identifier and
of each item are displayed with right
alignment.
Command Performed Successfully.
Verify text attribute of the alpha identifier and
of each item are displayed without right
alignment.
Remark: If right alignment is the Terminal's
default alignment as declared in table A.2/9,
no alignment change will take place.
Release 10
Step
20
365
Direction
Message/Action
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
PROACTIVE COMMAND: SET UP MENU 6.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
Text colour:
0
14
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Foreground: black, background: white
ETSI
Release 10
366
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
02
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
02
25
6B
01
65
33
B4
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
02
81
4D
6D
8F
0E
B4
82
65
20
07
02
00
85
6E
31
03
B4
06
TERMINAL RESPONSE: SET UP MENU 6.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
83
01
00
00
69
49
6D
82
74
74
20
02
20
65
35
81
4D
6D
8F
82
65
20
07
85
6E
34
06
PROACTIVE COMMAND: SET UP MENU 6.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 2"
Item
Identifier of item:
Text string of item:
4
"Item 4"
Identifier of item:
Text string of item:
5
"Item 5"
Identifier of item:
Text string of item:
6
"Item 6"
Item
Item
Coding:
BER-TLV:
D0
0E
75
8F
49
34
54
20
07
74
81
6F
32
05
65
03
6F
8F
49
6D
01
6C
07
74
20
25
6B
04
65
36
ETSI
Release 10
367
27.22.4.8.6.3.5
ETSI TS 102 384 V10.3.0 (2015-08)
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.3.
27.22.4.8.6.4
SET UP MENU (support of Text Attribute - Large Font Size) and ENVELOPE MENU
SELECTION
27.22.4.8.6.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.4.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.4.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the large font size text attribute configuration within the command Set Up
Menu and the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.6.4.4
Method of test
27.22.4.8.6.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.4.4.2
Procedure
Expected Sequence 6.4 (SET UP MENU, Text Attribute - Large Font Size, successful)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 6.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3" Verify that the alpha identifier and each item
under the header of "Toolkit Menu is displayed with large font size.
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
ETSI
Release 10
Step
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
368
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.4.1
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with normal font size.
Command Performed Successfully.
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3" Verify that the alpha identifier and each item
under the header of "Toolkit Menu is displayed with large font size.
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.3
Terminal → USER Integrate the menu header of
"Toolkit Menu 3" into its menu
system and have the menu items
of "Item 7", "Item 8", "Item 9" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 6.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 3"
ETSI
Release 10
Step
38
39
40
369
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → USER Display "Item 7", "Item 8", "Item 9" Verify that the alpha identifier and each item
under the header of "Toolkit Menu is displayed with normal font size.
3".
USER → Terminal Navigate in the items, then select
"Item 8".
Terminal → UICC Send the ENVELOPE 6.4.1:
MENU SELECTION
(Identifier of item: 8)
PROACTIVE COMMAND: SET UP MENU 6.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
14
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
370
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
04
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
04
25
6B
01
65
33
B4
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
04
81
4D
6D
8F
0E
B4
82
65
20
07
04
00
85
6E
31
03
B4
06
83
01
00
TERMINAL RESPONSE: SET UP MENU 6.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
PROACTIVE COMMAND: SET UP MENU 6.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 2"
Item
Identifier of item:
Text string of item:
4
"Item 4"
Identifier of item:
Text string of item:
5
"Item 5"
Identifier of item:
Text string of item:
6
"Item 6"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
14
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
371
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
00
48
54
20
07
74
0C
B4
81
6F
32
05
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
00
25
6B
04
65
36
B4
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
35
00
00
81
4D
6D
8F
0E
B4
82
65
20
07
00
00
85
6E
34
06
B4
06
00
69
49
6D
82
74
74
20
02
20
65
38
81
4D
6D
8F
82
65
20
07
85
6E
37
09
PROACTIVE COMMAND: SET UP MENU 6.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 3"
Item
Identifier of item:
Text string of item:
7
"Item 7"
Identifier of item:
Text string of item:
8
"Item 8"
Identifier of item:
Text string of item:
9
"Item 9"
Item
Item
Coding:
BER-TLV:
D0
0E
75
8F
49
34
54
20
07
74
81
6F
33
08
65
03
6F
8F
49
6D
01
6C
07
74
20
25
6B
07
65
39
ETSI
Release 10
372
ETSI TS 102 384 V10.3.0 (2015-08)
ENVELOPE 6.4.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
08
Coding:
BER-TLV:
27.22.4.8.6.4.5
D3
07
82
02
01
81
90
01
08
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.4.
27.22.4.8.6.5
SET UP MENU (support of Text Attribute - Small Font Size) and ENVELOPE MENU
SELECTION
27.22.4.8.6.5.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.5.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.5.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the with small font size text attribute configuration within the command Set
Up Menu and the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
27.22.4.8.6.5.4
Method of test
27.22.4.8.6.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.5.4.2
Procedure
Expected Sequence 6.5 (SET UP MENU, Text Attribute - Small Font Size, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.5.1
ETSI
Comments
Release 10
Step
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
373
Direction
Message/Action
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.5.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with small font size.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with normal font size.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with small font size.
Release 10
Step
30
31
32
33
34
35
36
37
38
39
40
374
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.3
Terminal → USER Integrate the menu header of
"Toolkit Menu 3" into its menu
system and have the menu items
of "Item 7", "Item 8", "Item 9" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 6.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 3"
Terminal → USER Display "Item 7", "Item 8", "Item 9" Verify that the alpha identifier and each item
under the header of "Toolkit Menu is displayed with normal font size.
3".
USER → Terminal Navigate in the items, then select
"Item 8".
Terminal → UICC Send the ENVELOPE 6.4.1:
MENU SELECTION
(Identifier of item: 8)
PROACTIVE COMMAND: SET UP MENU 6.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
0
14
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
ETSI
Release 10
375
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
6
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
08
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
08
25
6B
01
65
33
B4
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
08
81
4D
6D
8F
0E
B4
82
65
20
07
08
00
85
6E
31
03
B4
06
83
01
00
TERMINAL RESPONSE: SET UP MENU 6.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.6.5.5
81
03
01
25
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.5.
27.22.4.8.6.6
SET UP MENU (support of Text Attribute - Bold On) and ENVELOPE MENU
SELECTION
27.22.4.8.6.6.1
Definition and applicability
See clause 3.2.2.
ETSI
Release 10
376
27.22.4.8.6.6.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.6.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the text attribute configuration within the command Set Up Menu and the
Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE (MENU
SELECTION) command.
27.22.4.8.6.6.4
Method of test
27.22.4.8.6.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.6.4.2
Procedure
Expected Sequence 6.6 (SET UP MENU, Text Attribute - Bold On, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.6.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 6.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3" Verify that the alpha identifier and each item
under the header of "Toolkit Menu is displayed with bold on.
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
ETSI
Release 10
Step
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
377
Direction
Message/Action
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.6.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.3
Terminal → USER Integrate the menu header of
"Toolkit Menu 3" into its menu
system and have the menu items
of "Item 7", "Item 8", "Item 9" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 3"
Terminal → USER Display "Item 7", "Item 8", "Item 9"
under the header of "Toolkit Menu
3".
USER → Terminal Navigate in the items, then select
"Item 8".
Terminal → UICC Send the ENVELOPE 6.4.1:
MENU SELECTION
(Identifier of item: 8)
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with bold off.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with bold on.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with bold off.
Release 10
378
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SET UP MENU 6.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
14
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
10
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
10
25
6B
01
65
33
B4
ETSI
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
10
81
4D
6D
8F
0E
B4
82
65
20
07
10
00
85
6E
31
03
B4
06
Release 10
379
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP MENU 6.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.6.6.5
81
03
01
25
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.6.
27.22.4.8.6.7
SET UP MENU (support of Text Attribute - Italic On) and ENVELOPE MENU
SELECTION
27.22.4.8.6.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.7.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.7.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the text attribute configuration within the command Set Up Menu and the
Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE (MENU
SELECTION) command.
27.22.4.8.6.7.4
Method of test
27.22.4.8.6.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.7.4.2
Procedure
Expected Sequence 6.7 (SET UP MENU, Text Attribute - Italic On, successful)
Step
1
2
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.7.1
Terminal → UICC FETCH
ETSI
Comments
Release 10
Step
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
380
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.7.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6'
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.7.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with italics on.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with italics off.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with italics on.
Release 10
Step
29
30
31
32
33
34
35
36
37
38
39
40
381
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.3
Terminal → USER Integrate the menu header of
"Toolkit Menu 3" into its menu
system and have the menu items
of "Item 7", "Item 8", "Item 9" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 6.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 3"
Terminal → USER Display "Item 7", "Item 8", "Item 9" Verify that the alpha identifier and each item
under the header of "Toolkit Menu is displayed with italics off.
3".
USER → Terminal Navigate in the items, then select
"Item 8".
Terminal → UICC Send the ENVELOPE 6.4.1:
MENU SELECTION
(Identifier of item: 8)
PROACTIVE COMMAND: SET UP MENU 6.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
14
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
382
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
6
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
20
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
20
25
6B
01
65
33
B4
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
20
81
4D
6D
8F
0E
B4
82
65
20
07
20
00
85
6E
31
03
B4
06
83
01
00
TERMINAL RESPONSE: SET UP MENU 6.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.6.7.5
81
03
01
25
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.7.
27.22.4.8.6.8
SET UP MENU (support of Text Attribute - Underline On) and ENVELOPE MENU
SELECTION
27.22.4.8.6.8.1
Definition and applicability
See clause 3.2.2.
ETSI
Release 10
383
27.22.4.8.6.8.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.8.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the text attribute configuration within the command Set Up Menu and the
Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE (MENU
SELECTION) command.
27.22.4.8.6.8.4
Method of test
27.22.4.8.6.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.8.4.2
Procedure
Expected Sequence 6.8 (SET UP MENU, Text Attribute - Underline On, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.8.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 6.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3" Verify that the alpha identifier and each item
under the header of "Toolkit Menu is displayed with underline on.
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
ETSI
Release 10
Step
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
384
Direction
Message/Action
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.8.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.3
Terminal → USER Integrate the menu header of
"Toolkit Menu 3" into its menu
system and have the menu items
of "Item 7", "Item 8", "Item 9" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 3"
Terminal → USER Display "Item 7", "Item 8", "Item 9"
under the header of "Toolkit Menu
3".
USER → Terminal Navigate in the items, then select
"Item 8".
Terminal → UICC Send the ENVELOPE 6.4.1:
MENU SELECTION
(Identifier of item: 8)
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with underline off.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with underline on.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with underline off.
Release 10
385
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SET UP MENU 6.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
14
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
40
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
40
25
6B
01
65
33
B4
ETSI
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
40
81
4D
6D
8F
0E
B4
82
65
20
07
40
00
85
6E
31
03
B4
06
Release 10
386
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP MENU 6.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.6.8.5
81
03
01
25
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.8.
27.22.4.8.6.9
SET UP MENU (support of Text Attribute - Strikethrough On) and ENVELOPE MENU
SELECTION
27.22.4.8.6.9.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.9.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.9.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the text attribute configuration within the command Set Up Menu and the
Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE (MENU
SELECTION) command.
27.22.4.8.6.9.4
Method of test
27.22.4.8.6.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
ETSI
Release 10
387
27.22.4.8.6.9.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 6.9 (SET UP MENU, Text Attribute - Strikethrough On, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.9.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.2
Terminal → USER Integrate the menu header of
"Toolkit Menu 2" into its menu
system and have the menu items
of "Item 4", "Item 5", "Item 6" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 2"
Terminal → USER Display "Item 4", "Item 5", "Item 6"
under the header of "Toolkit Menu
2".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC Send the ENVELOPE 6.1.2:
MENU SELECTION
(Identifier of item: 5)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.9.1
Terminal → USER Integrate the menu header of
"Toolkit Menu 1" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.9.1
ETSI
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with strikethrough on.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with strikethrough off.
Command Performed Successfully.
Release 10
Step
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
388
Direction
Message/Action
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 1"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit Menu
1".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.3
Terminal → USER Integrate the menu header of
"Toolkit Menu 3" into its menu
system and have the menu items
of "Item 7", "Item 8", "Item 9" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 3"
Terminal → USER Display "Item 7", "Item 8", "Item 9"
under the header of "Toolkit Menu
3".
USER → Terminal Navigate in the items, then select
"Item 8".
Terminal → UICC Send the ENVELOPE 6.4.1:
MENU SELECTION
(Identifier of item: 8)
PROACTIVE COMMAND: SET UP MENU 6.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu 1"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Verify that the alpha identifier and each item
is displayed with strikethrough on.
Command Performed Successfully.
Verify that the alpha identifier and each item
is displayed with strikethrough off.
Release 10
389
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
14
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0E
75
8F
49
D1
80
48
54
20
07
74
0C
B4
81
6F
31
02
65
00
03
6F
8F
49
6D
06
01
6C
07
74
20
80
25
6B
01
65
33
B4
00
69
49
6D
D0
00
82
74
74
20
04
06
02
20
65
32
00
80
81
4D
6D
8F
0E
B4
82
65
20
07
80
00
85
6E
31
03
B4
06
83
01
00
TERMINAL RESPONSE: SET UP MENU 6.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.6.9.5
81
03
01
25
00
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.9.
ETSI
82
81
Release 10
390
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4.8.6.10
SET UP MENU (support of Text Attribute - Foreground and Background Colour) and
ENVELOPE MENU SELECTION
27.22.4.8.6.10.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.6.10.2
Conformance requirement
Requirements are the same as in clause 27.22.4.8.1.1, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.8.6.10.3
Test purpose
To verify that the Terminal correctly integrates the menu items contained in the SET UP MENU proactive UICC
command, and returns a successful response in the TERMINAL RESPONSE command sent to the UICC.
To verify that text is displayed according to the text attribute configuration within the command Set Up Menu and the
Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE (MENU
SELECTION) command.
27.22.4.8.6.10.4
Method of test
27.22.4.8.6.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.6.10.4.2
Procedure
Expected Sequence 6.10 (SET UP MENU, Text Attribute - Foreground and Background Colour, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.10.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.10.1
Terminal → USER Integrate the menu header of
"Toolkit Menu" into its menu
system and have the menu items
of "Item 1", "Item 2", "Item 3" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.10.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu"
Terminal → USER Display "Item 1", "Item 2", "Item 3"
under the header of "Toolkit
Menu".
USER → Terminal Navigate in the items, then select
"Item 2".
Terminal → UICC Send the ENVELOPE 6.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 6.4.3
Terminal → UICC FETCH
ETSI
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is formatted according to the foreground and
background colour text attribute configuration.
Release 10
Step
13
14
15
16
17
18
19
20
391
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 6.4.3
Terminal → USER Integrate the menu header of
"Toolkit Menu 3" into its menu
system and have the menu items
of "Item 7", "Item 8", "Item 9" under
this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 6.10.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "Toolkit
Menu 3"
Terminal → USER Display "Item 7", "Item 8", "Item 9"
under the header of "Toolkit Menu
3".
USER → Terminal Navigate in the items, then select
"Item 8".
Terminal → UICC Send the ENVELOPE 6.4.1:
MENU SELECTION
(Identifier of item: 8)
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command Performed Successfully.
Verify that the alpha identifier and each item
is formatted with the Terminal's default
foreground and background colour
PROACTIVE COMMAND: SET UP MENU 6.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Menu"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
12
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
392
Item #2
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #3
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
0C
75
02
65
00
46
54
8F
49
6D
06
81
6F
07
74
20
00
03
6F
01
65
33
B4
01
6C
49
6D
D0
00
25
6B
74
20
04
06
00
69
65
32
00
00
82
74
6D
8F
0C
B4
02
20
20
07
00
00
81
4D
31
03
B4
06
82
65
8F
49
D1
00
85
6E
07
74
0C
B4
83
01
00
TERMINAL RESPONSE: SET UP MENU 6.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.8.6.10.5
81
03
01
25
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 6.10.
27.22.4.8.7
27.22.4.8.7.1
SET UP MENU (UCS2 display in Cyrillic) and ENVELOPE MENU SELECTION
Definition and applicability
See clause 3.2.2.
27.22.4.8.7.2
Conformance requirement
The Terminal shall support the SET UP MENU command as defined in:
•
ETSI TS 102 223 [1], clauses 5, 6.4.8, 6.6.7, 6.8, 6.11, 8.6, 8.7, 8.2, 8.9 and 9.4.
The Terminal shall support MENU SELECTION as defined in:
•
ETSI TS 102 223 [1], clauses 4.4, 5.2, 6.4.8, 6.9, 7.2, 8.7 and 8.10.
ETSI
Release 10
393
27.22.4.8.7.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal correctly integrates the menu items in UCS2 coding contained in the SET UP MENU
proactive UICC command, and returns a successful response in the TERMINAL RESPONSE command sent to the
UICC.
To verify that the Terminal replaces the current list of menu items with the list of menu items contained in the SET UP
MENU command.
To verify that the Terminal removes the current list of menu items following receipt of a SET UP MENU command
with no items.
To verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
To verify that when the help is available for the command and the user gas indicated the need to get help information on
one of the items, the Terminal informs properly the UICC about an HELP REQUEST, using the MENU SELECTION
mechanism.
27.22.4.8.7.4
Method of test
27.22.4.8.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.7.4.2
Procedure
Expected Sequence 7.1 (SET UP MENU and MENU SELECTION, without Help Request, Replace and Remove
a Toolkit Menu, with UCS2 in Cyrillic Characters)
Step
1
2
3
4
5
6
7
8
9
10
11
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 7.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 7.1.1
Terminal → USER Integrate the menu header of
"ЗДРАВСТВУЙТЕ" into its menu
system and have the menu items
of "ЗДРАВСТВУЙТЕ1",
"ЗДРАВСТВУЙТЕ2",
"ЗДРАВСТВУЙТЕ3" and
"ЗДРАВСТВУЙТЕ4" under this
header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 7.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu
"ЗДРАВСТВУЙТЕ"
Terminal → USER Display "ЗДРАВСТВУЙТЕ1",
"ЗДРАВСТВУЙТЕ2",
"ЗДРАВСТВУЙТЕ3",
"ЗДРАВСТВУЙТЕ4
USER → Terminal Select the "ЗДРАВСТВУЙТЕ2"
Menu entry
Terminal → UICC Send the ENVELOPE 7.1.1:
MENU SELECTION
(Identifier of item: 2)
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 7.1.2
ETSI
Comments
First Set Up Menu.
"ЗДРАВСТВУЙТЕ": "Hello" in Russian.
Command Performed Successfully.
Second Set Up Menu, REPLACE Old Menu.
Release 10
Step
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
394
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 7.1.2
Terminal → USER Integrate the new menu header of
"ЗДРАВСТВУЙТЕ" into its menu
system and have the menu items
of "ЗДРАВСТВУЙТЕ5" and
"ЗДРАВСТВУЙТЕ6" under this
header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 7.1.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu
"ЗДРАВСТВУЙТЕ"
Terminal → USER Display "ЗДРАВСТВУЙТЕ5",
"ЗДРАВСТВУЙТЕ 6"
USER → Terminal Select the "ЗДРАВСТВУЙТЕ6"
menu entry
Terminal → UICC Send the ENVELOPE 7.1.2:
MENU SELECTION
(Identifier of item: 12)
Third Set Up Menu, REMOVE Toolkit Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 7.1.3
with SW1/SW2 of '91 0F'.
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 7.1.3
Terminal → USER Remove the menu
"ЗДРАВСТВУЙТЕ" from its menu
system.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 7.1.3
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Has to unsuccessfully find the
Toolkit Menu
PROACTIVE COMMAND: SET UP MENU 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"ЗДРАВСТВУЙТЕ"
Item
Identifier of item:
Text string of item:
1
"ЗДРАВСТВУЙТЕ1"
Identifier of item:
Text string of item:
2
"ЗДРАВСТВУЙТЕ2"
Identifier of item:
Text string of item:
3
"ЗДРАВСТВУЙТЕ3"
Identifier of item:
4
Item
Item
Item
ETSI
Release 10
395
ETSI TS 102 384 V10.3.0 (2015-08)
"ЗДРАВСТВУЙТЕ4"
Text string of item:
Coding:
BER-TLV:
D0
85
12
22
20
23
80
21
15
20
23
80
21
15
81
19
04
04
04
04
04
04
00
04
04
04
04
00
9C
80
21
15
10
19
17
22
32
10
19
17
22
34
81
04
04
8F
04
04
04
04
8F
04
04
04
04
03
17
22
1C
12
22
14
12
1C
12
22
14
12
01
04
04
01
04
04
04
04
03
04
04
04
04
25
14
12
80
21
15
20
23
80
21
15
20
23
00
04
04
04
04
00
04
04
04
04
00
04
04
82
20
23
17
22
31
10
19
17
22
33
10
19
02
04
04
04
04
8F
04
04
04
04
8F
04
04
81
10
19
14
12
1C
12
22
14
12
1C
12
22
82
04
04
04
04
02
04
04
04
04
04
04
04
82
20
23
17
22
35
10
19
02
04
04
04
04
8F
04
04
81
10
19
14
12
1C
12
22
82
04
04
04
04
12
04
04
85
12
22
20
23
80
21
15
PROACTIVE COMMAND: SET UP MENU 7.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"ЗДРАВСТВУЙТЕ"
Item
Identifier of item:
Text string of item:
"11"
"ЗДРАВСТВУЙТЕ5"
Identifier of item:
Text string of item:
"12"
"ЗДРАВСТВУЙТЕ6"
Item
Coding:
BER-TLV:
D0
19
04
04
04
04
04
04
00
60
80
21
15
10
19
17
22
36
81
04
04
8F
04
04
04
04
03
17
22
1C
12
22
14
12
01
04
04
11
04
04
04
04
25
14
12
80
21
15
20
23
PROACTIVE COMMAND: SET UP MENU 7.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
UICC
ETSI
00
04
04
04
04
00
04
04
Release 10
396
Destination device:
Alpha identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
Null data object
Item:
Empty
Coding:
BER-TLV:
D0
00
0D
8F
81
00
03
01
25
00
82
02
81
82
85
83
01
00
TERMINAL RESPONSE: SET UP MENU 7.1.1, 7.1.2 and 7.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
ENVELOPE 7.1.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
02
Coding:
BER-TLV:
D3
07
82
02
01
81
90
01
02
02
01
81
90
01
12
ENVELOPE 7.1.2: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
12
Coding:
BER-TLV:
27.22.4.8.7.5
D3
07
82
Test requirement
The Terminal shall operate in the manner defined in expected sequence 7.1.
ETSI
Release 10
397
27.22.4.8.8
ETSI TS 102 384 V10.3.0 (2015-08)
SET UP MENU (UCS2 display in Chinese) and ENVELOPE MENU SELECTION
27.22.4.8.8.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.8.2
Conformance requirement
The Terminal shall support the SET UP MENU command as defined in:
•
ETSI TS 102 223 [1], clauses 5, 6.4.8, 6.6.7, 6.8, 6.11, 8.6, 8.7, 8.2, 8.9 and 9.4.
The Terminal shall support MENU SELECTION as defined in:
•
ETSI TS 102 223 [1], clauses 4.4, 5.2, 6.4.8, 6.9, 7.2, 8.7 and 8.10.
27.22.4.8.8.3
Test purpose
To verify that the Terminal correctly integrates the menu items in UCS2 coding contained in the SET UP MENU
proactive UICC command, and returns a successful response in the TERMINAL RESPONSE command sent to the
UICC.
To verify that the Terminal replaces the current list of menu items with the list of menu items contained in the SET UP
MENU command.
To verify that the Terminal removes the current list of menu items following receipt of a SET UP MENU command
with no items.
To verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
To verify that when the help is available for the command and the user gas indicated the need to get help information on
one of the items, the Terminal informs properly the UICC about an HELP REQUEST, using the MENU SELECTION
mechanism.
27.22.4.8.8.4
Method of test
27.22.4.8.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.8.4.2
Procedure
Expected Sequence 8.1 (SET UP MENU and MENU SELECTION, without Help Request, Replace and Remove
a Toolkit Menu, with UCS2 - Chinese Characters)
Step
1
2
3
4
5
Direction
Message/Action
Comments
First Set Up Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 8.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 8.1.1
Terminal → USER Integrate the menu header of "
"
": "Toolkit Menu" in Chinese.
工具 工具箱单
箱单" into its menu system and "项目一": "Item 1" in Chinese.
have the menu items of "项目一", " "项目二": "Item 2" in Chinese.
项目二", "项目三" and "项目四" "项目三": "Item 3" in Chinese.
under this header.
"项目四": "Item 4" in Chinese.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 8.1.1
ETSI
Command Performed Successfully.
Release 10
Step
6
7
398
Direction
Message/Action
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "
Terminal → USER
8
9
10
11
12
13
14
ETSI TS 102 384 V10.3.0 (2015-08)
USER → Terminal
Comments
工具箱单"
Display "项目一", "项目二", "项目三
", "项目四"
Select the "项目二" Menu entry
Terminal → UICC Send the ENVELOPE 8.1.1:
MENU SELECTION
(Identifier of item: 2)
Second Set Up Menu, REPLACE Old Menu
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 8.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 8.1.2
Terminal → USER Integrate the new menu header of " ": "One" in Chinese.
" into its menu system
"
" ": "Two" in Chinese.
and have the menu items of " "
工具箱单
一
二
一
二
17
and " " under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 8.1.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "
"
18
Terminal → USER Display "
19
USER → Terminal Select the " " menu entry
Terminal → UICC Send the ENVELOPE 8.1.2:
MENU SELECTION
(Identifier of item: 12)
Third Set Up Menu, REMOVE Toolkit Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 8.1.3
with SW1/SW2 of '91 0F'.
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 8.1.3
Terminal → USER Remove the menu "
" from
15
16
20
21
22
23
24
25
26
27
工具箱单
一", "二"
二
工具箱单
its menu system.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 8.1.3
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Has to unsuccessfully find the
Toolkit Menu
PROACTIVE COMMAND: SET UP MENU 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
UICC
Terminal
Alpha identifier:
"
工具箱单"
ETSI
Command Performed Successfully.
Release 10
399
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
1
Text string of item:
"
Identifier of item:
2
Text string of item:
"
Item
Item
项目一"
项目二"
Identifier of item:
3
Text string of item:
"
Item
项目三"
Identifier of item:
4
Text string of item:
"
项目四"
Coding:
BER-TLV:
D0
09
01
98
76
56
3C
80
80
79
EE
DB
81
5D
98
76
4E
03
E5
79
EE
09
01
51
76
4E
8F
25
77
EE
8C
08
00
7B
4E
8F
04
82
B1
00
08
80
02
53
8F
03
98
81
55
08
80
79
82
8F
02
98
76
85
08
80
79
EE
00
7B
12
82
B1
80
02
53
4E
81
55
8C
82
8F
85
04
PROACTIVE COMMAND: SET UP MENU 8.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
UICC
Terminal
工具箱单"
Alpha identifier:
"
Identifier of item:
"11"
Text string of item:
"
Identifier of item:
"12"
Text string of item:
"
Item
Item
一"
二"
Coding:
BER-TLV:
D0
09
11
20
80
80
81
5D
4E
03
E5
00
01
51
8F
25
77
04
PROACTIVE COMMAND: SET UP MENU 8.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
ETSI
Release 10
400
Device identities
Source device:
Destination device:
Alpha identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
Null data object
Item: Empty
Coding:
BER-TLV:
D0
00
0D
8F
81
00
03
01
25
00
82
02
81
82
85
83
01
00
TERMINAL RESPONSE: SET UP MENU 8.1.1, 8.1.2 and 8.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
ENVELOPE 8.1.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
02
Coding:
BER-TLV:
D3
07
82
02
01
81
90
01
02
02
01
81
90
01
12
ENVELOPE 8.1.2: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
12
Coding:
BER-TLV:
27.22.4.8.8.5
D3
07
82
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.1.
ETSI
Release 10
401
27.22.4.8.9
ETSI TS 102 384 V10.3.0 (2015-08)
SET UP MENU (UCS2 display in Katakana) and ENVELOPE MENU
SELECTION
27.22.4.8.9.1
Definition and applicability
See clause 3.2.2.
27.22.4.8.9.2
Conformance requirement
The Terminal shall support the SET UP MENU command as defined in:
•
ETSI TS 102 223 [1], clauses 5, 6.4.8, 6.6.7, 6.8, 6.11, 8.6, 8.7, 8.2, 8.9 and 9.4.
The Terminal shall support MENU SELECTION as defined in:
•
ETSI TS 102 223 [1], clauses 4.4, 5.2, 6.4.8, 6.9, 7.2, 8.7 and 8.10.
27.22.4.8.9.3
Test purpose
To verify that the Terminal correctly integrates the menu items in UCS2 coding contained in the SET UP MENU
proactive UICC command, and returns a successful response in the TERMINAL RESPONSE command sent to the
UICC.
To verify that the Terminal replaces the current list of menu items with the list of menu items contained in the SET UP
MENU command.
To verify that the Terminal removes the current list of menu items following receipt of a SET UP MENU command
with no items.
To verify that the Terminal correctly passes the identifier of the selected menu item to the UICC using the ENVELOPE
(MENU SELECTION) command.
To verify that when the help is available for the command and the user gas indicated the need to get help information on
one of the items, the Terminal informs properly the UICC about an HELP REQUEST, using the MENU SELECTION
mechanism.
27.22.4.8.9.4
Method of test
27.22.4.8.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
The Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.8.9.4.2
Procedure
Expected Sequence 9.1 (SET UP MENU and MENU SELECTION, without Help Request, Replace and Remove
a Toolkit Menu, with UCS2 in Katakana Characters)
Step
1
2
3
4
Direction
Message/Action
Comments
First Set Up Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 9.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 9.1.1
Terminal → USER Integrate the menu header of "80 Menu Header and menu items use characters
0" into its menu system and
in Katakana.
have the menu items of "80 1",
ル
ル
5
ル
ル
ル
"80 2", "80 3" and "80 4"
under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 9.1.1
ETSI
Command Performed Successfully.
Release 10
Step
6
402
ETSI TS 102 384 V10.3.0 (2015-08)
7
Direction
Message/Action
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "80 0"
8
Terminal → USER
9
10
USER → Terminal
Terminal → UICC Send the ENVELOPE 9.1.1:
MENU SELECTION
(Identifier of item: 2)
Second Set Up Menu, REPLACE Old Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 9.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 9.1.2
Terminal → USER Integrate the new menu header of
"80 0" into its menu system and
11
12
13
14
Comments
ル
Display "80ル1", "80ル2", "80ル3",
"80ル4"
Select the "80ル2" Menu entry
ル
ル
have the menu items of "80 5"
ル
15
16
17
18
19
20
21
22
23
24
25
26
27
and "80 6" under this header.
Terminal → UICC TERMINAL RESPONSE: SET UP Command Performed Successfully.
MENU 9.1.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select the Toolkit Menu "80 0"
Terminal → USER Display "80 5", "80 6"
USER → Terminal Select the "80 6" menu entry
Terminal → UICC Send the ENVELOPE 9.1.2:
MENU SELECTION
(Identifier of item: 12)
Third Set Up Menu, REMOVE Toolkit Menu.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP MENU 9.1.3
with SW1/SW2 of '91 0F'.
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND SET UP
MENU 9.1.3
Terminal → USER Remove the menu "80 0" from its
ル
ル
ル
ル
ル
menu system.
Terminal → UICC TERMINAL RESPONSE: SET UP
MENU 9.1.3
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Has to unsuccessfully find the
Toolkit Menu
PROACTIVE COMMAND: SET UP MENU 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
UICC
Terminal
Alpha identifier:
"80
Identifier of item:
1
Text string of item:
"80
ル0"
Item
ル1"
ETSI
Command Performed Successfully.
Release 10
403
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
2
Text string of item:
"80
Identifier of item:
3
Text string of item:
"80
Item
Item
Identifier of item:
4
Text string of item:
"80
ル2"
ル3"
ル4"
Coding:
BER-TLV:
D0
09
01
02
03
04
44
80
80
80
80
80
81
00
00
00
00
00
03
38
38
38
38
38
01
00
00
00
00
00
25
30
30
30
30
30
00
30
30
30
30
30
82
EB
EB
EB
EB
EB
02
00
00
00
00
00
81
30
31
32
33
34
82
8F
8F
8F
8F
85
0A
0A
0A
0A
00
30
30
30
82
EB
EB
EB
02
00
00
00
81
30
35
36
82
8F
8F
85
0A
0A
PROACTIVE COMMAND: SET UP MENU 9.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
1
SET UP MENU
"00"
UICC
Terminal
Alpha identifier:
"80
ル0"
Item
Identifier of item:
"11"
Text string of item:
"80
ル5"
Item
Identifier of item:
"12"
Text string of item:
"80
ル6"
Coding:
BER-TLV:
D0
09
11
12
2C
80
80
80
81
00
00
00
03
38
38
38
01
00
00
00
25
30
30
30
PROACTIVE COMMAND: SET UP MENU 9.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
Null data object
ETSI
Release 10
404
ETSI TS 102 384 V10.3.0 (2015-08)
Item: Empty
Coding:
BER-TLV:
D0
00
0D
8F
81
00
03
01
25
00
82
02
81
82
85
83
01
00
TERMINAL RESPONSE: SET UP MENU 9.1.1, 9.1.2 and 9.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP MENU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
25
00
82
02
82
81
ENVELOPE 9.1.1: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
02
Coding:
BER-TLV:
D3
07
82
02
01
81
90
01
02
02
01
81
90
01
12
ENVELOPE 9.1.2: MENU SELECTION
Logically:
Menu selection
Device identities
Source device:
Destination device:
Item identifier
Keypad
UICC
12
Coding:
BER-TLV:
27.22.4.8.9.5
D3
07
82
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.1.
ETSI
Release 10
405
27.22.4.9
ETSI TS 102 384 V10.3.0 (2015-08)
SELECT ITEM
27.22.4.9.1
27.22.4.9.1.1
SELECT ITEM (mandatory features for Terminal supporting SELECT ITEM)
Definition and applicability
See clause 3.2.2.
27.22.4.9.1.2
Conformance requirement
The Terminal shall support the Proactive UICC: Select Item facility as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5, 6.4.9, 6.6.8, 6.8, 8.6, 8.7, 8.2, 8.9, 9.4 and 10.
27.22.4.9.1.3
Test purpose
To verify that the Terminal correctly presents the set of items contained in the SELECT ITEM proactive UICC
command, and returns a TERMINAL RESPONSE command to the UICC with the identifier of the item chosen.
To verify that the Terminal allows a SELECT ITEM proactive UICC command within the maximum 255 byte
BER-TLV boundary.
To verify that the Terminal returns a TERMINAL RESPONSE with "Proactive UICC application session terminated by
the user", if the user has indicated the need to end the proactive UICC session.
To verify that the Terminal returns a TERMINAL RESPONSE with "Backwards move in the proactive UICC
application session requested by the user", if the user has indicated the need to go backwards in the proactive UICC
application session.
27.22.4.9.1.4
Method of test
27.22.4.9.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.1.4.2
Procedure
Expected Sequence 1.1 (SELECT ITEM, mandatory features, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 1.1.1
Terminal → USER Display items of "Item 1", "Item 2",
"Item 3" and "Item 4" under the
header of "Toolkit Select".
USER → Terminal Select "Item 2".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 1.1.1
PROACTIVE COMMAND: SELECT ITEM 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
ETSI
Release 10
406
Device identities
Source device:
Destination device:
Alpha identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
1
"Item 1"
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Identifier of item:
Text string of item:
4
"Item 4"
Item
Item
Item
Coding:
BER-TLV:
D0
0E
65
8F
49
6D
3D
54
63
07
74
20
81
6F
74
02
65
34
03
6F
8F
49
6D
01
6C
07
74
20
24
6B
01
65
33
00
69
49
6D
8F
82
74
74
20
07
02
20
65
32
04
81
53
6D
8F
49
82
65
20
07
74
85
6C
31
03
65
83
01
00
TERMINAL RESPONSE: SELECT ITEM 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
81
90
03
01
01
02
24
00
82
02
82
81
Expected Sequence 1.2 (SELECT ITEM, large menu, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 1.2.1
ETSI
Comments
Release 10
Step
4
5
6
407
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → USER Present the items of "Zero", "One",
"Two", Three", "Four", "Five", "Six",
"Seven", "Eight", "Nine", "Alpha",
"Bravo", "Charlie", "Delta", "Echo",
"Fox-trot", "Black", "Brown", "Red",
"Orange", "Yellow", "Green",
"Blue", "Violet", "Grey", "White",
"milli", "micro", "nano" and "pico"
under the header of "LargeMenu1"
USER → Terminal Select item "Orange".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 1.2.1
PROACTIVE COMMAND: SELECT ITEM 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"LargeMenu1"
Item
Identifier of item:
Text string of item:
"50"
"Zero"
Identifier of item:
Text string of item:
"4F"
"One"
Identifier of item:
Text string of item:
"4E"
"Two"
Identifier of item:
Text string of item:
"4D"
"Three"
Identifier of item:
Text string of item:
"4C"
"Four"
Identifier of item:
Text string of item:
"4B"
"Five"
Identifier of item:
Text string of item:
"4A"
"Six"
Identifier of item:
Text string of item:
"49"
"Seven"
Identifier of item:
Text string of item:
"48"
"Eight"
Identifier of item:
Text string of item:
"47"
"Nine"
Identifier of item:
Text string of item:
"46"
"Alpha"
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
ETSI
Release 10
408
Item
Identifier of item:
Text string of item:
"45"
"Bravo"
Identifier of item:
Text string of item:
"44"
"Charlie"
Identifier of item:
Text string of item:
"43"
"Delta"
Identifier of item:
Text string of item:
"42"
"Echo"
Identifier of item:
Text string of item:
"41"
"Fox-trot"
Identifier of item:
Text string of item:
"40"
"Black"
Identifier of item:
Text string of item:
"3F"
"Brown"
Identifier of item:
Text string of item:
"3E"
"Red"
Identifier of item:
Text string of item:
"3D"
"Orange"
Identifier of item:
Text string of item:
"3C"
"Yellow"
Identifier of item:
Text string of item:
"3B"
"Green"
Identifier of item:
Text string of item:
"3A"
"Blue"
Identifier of item:
Text string of item:
"39"
"Violet"
Identifier of item:
Text string of item:
"38"
"Grey"
Identifier of item:
Text string of item:
"37"
"White"
Identifier of item:
Text string of item:
"36"
"milli"
Identifier of item:
Text string of item:
"35"
"micro"
Identifier of item:
Text string of item:
"34"
"nano"
Identifier of item:
Text string of item:
"33"
"pico"
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
Item
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Release 10
409
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
85
8F
65
72
4B
06
67
46
76
8F
63
6F
3F
8F
59
65
56
79
6D
6F
69
81
0A
05
8F
65
46
49
68
41
6F
06
68
74
42
07
65
6E
69
8F
69
8F
63
FC
4C
50
04
65
69
53
74
6C
8F
43
6F
8F
72
3D
6C
8F
6F
06
6C
05
6F
81
61
5A
4E
8F
76
65
8F
70
08
44
8F
06
6F
4F
6C
05
6C
37
6C
34
03
72
65
54
05
65
76
05
68
44
65
09
40
77
72
6F
3A
65
57
69
6E
01
67
72
77
4C
8F
65
47
61
43
6C
41
42
6E
61
77
42
74
68
8F
61
24
65
6F
6F
46
04
6E
4E
8F
68
74
46
6C
8F
6E
8F
6C
8F
69
06
6E
00
4D
8F
8F
6F
4A
8F
69
06
61
61
6F
61
04
67
06
75
05
74
35
6F
82
65
04
06
75
53
06
6E
45
72
8F
78
63
3E
65
3B
65
38
65
6D
8F
02
6E
4F
4D
72
69
48
65
42
6C
05
2D
6B
52
8F
47
8F
47
8F
69
05
81
75
4F
54
8F
78
45
8F
72
69
42
74
8F
65
07
72
07
72
06
63
33
82
31
6E
68
05
8F
69
06
61
65
45
72
06
64
3C
65
39
65
36
72
70
83
01
00
TERMINAL RESPONSE: SELECT ITEM 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
3D
Coding:
BER-TLV:
81
90
03
01
01
3D
24
00
82
02
82
81
Expected Sequence 1.3 (SELECT ITEM, call options, successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 1.3.1
ETSI
Comments
Release 10
Step
4
5
6
7
410
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → USER Present the items of " Call
Forwarding Unconditional", "Call
Forwarding On User Busy", "Call
Forwarding On No Reply", "Call
Forwarding On User Not
Reachable", "Barring Of All
Outgoing Calls", "Barring Of All
Outgoing International Calls" and
"CLI Presentation" under the
header of " LargeMenu2
USER → Terminal Select item "Barring Of All
Outgoing Calls".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 1.3.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: SELECT ITEM 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"LargeMenu2"
Item
Identifier of item:
Text string of item:
"FF"
"Call Forwarding Unconditional"
Identifier of item:
Text string of item:
"FE"
"Call Forwarding On User Busy"
Identifier of item:
Text string of item:
"FD"
"Call Forwarding On No Reply"
Identifier of item:
Text string of item:
"FC"
"Call Forwarding On User Not Reachable"
Identifier of item:
Text string of item:
"FB"
"Barring Of All Outgoing Calls"
Identifier of item:
Text string of item:
"FA"
"Barring Of All Outgoing International Calls"
Identifier of item:
Text string of item:
"F9"
"CLI Presentation"
Item
Item
Item
Item
Item
Item
ETSI
Release 10
411
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
85
8F
61
64
61
6E
75
6F
20
43
69
4E
65
4F
69
42
6C
49
6C
49
6F
81
0A
1E
72
69
6C
67
73
72
4E
61
6E
6F
8F
66
6E
61
6C
6E
20
20
6E
FB
4C
FF
64
74
6C
20
79
77
6F
6C
67
74
1E
20
67
72
20
74
43
50
81
61
43
69
69
20
4F
8F
61
20
6C
20
20
FB
41
20
72
4F
65
61
72
03
72
61
6E
6F
46
6E
1C
72
52
20
4F
52
42
6C
43
69
75
72
6C
65
01
67
6C
67
6E
6F
20
FD
64
65
46
6E
65
61
6C
61
6E
74
6E
6C
73
24
65
6C
20
61
72
55
43
69
70
6F
20
61
72
20
6C
67
67
61
73
65
00
4D
20
55
6C
77
73
61
6E
6C
72
55
63
72
4F
6C
20
6F
74
8F
6E
82
65
46
6E
8F
61
65
6C
67
79
77
73
68
69
75
73
4F
69
69
11
74
02
6E
6F
63
1D
72
72
6C
20
8F
61
65
61
6E
74
8F
66
6E
6F
F9
61
81
75
72
6F
FE
64
20
20
4F
26
72
72
62
67
67
2C
20
67
6E
43
74
82
32
77
6E
43
69
42
46
6E
FC
64
20
6C
20
6F
FA
41
20
61
4C
69
83
01
00
TERMINAL RESPONSE: SELECT ITEM 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
FB
Coding:
BER-TLV:
81
90
03
01
01
FB
24
00
82
ETSI
02
82
81
Release 10
412
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.4 (SELECT ITEM, backward move by user, successful)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 1.4.1
Terminal → USER Present the items of "One" and
"Two" under the header of "Select
Item".
USER → Terminal Indicate to go backwards in the
proactive UICC application
session.
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 1.4.1A
or
TERMINAL RESPONSE: SELECT
ITEM 1.4.1B
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 1.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 1.4.2
Terminal → USER Present the items of "One" and
"Two" under the header of "Select
Item".
USER → Terminal Indicate to end the proactive UICC
application and return the Terminal
to normal operation.
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 1.4.2A
or
TERMINAL RESPONSE: SELECT
ITEM 1.4.2B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
Backward move in the proactive UICC
application session requested by user.
Proactive UICC application terminated by the
user.
PROACTIVE COMMAND: SELECT ITEM 1.4.1 and 1.4.2
Logically:
Command details
Command number:
Command type:
Device identities
Source device:
Destination device:
1
SELECT ITEM
Command qualifier: "00"
UICC
Terminal
Alpha identifier: "Select Item"
Item
Identifier of item:
Text string of item:
"11"
"One"
Identifier of item:
Text string of item:
"12"
"Two"
Item
Coding:
BER-TLV:
D0
0B
8F
22
53
04
81
65
11
03
6C
4F
01
65
6E
24
63
65
ETSI
00
74
8F
82
20
04
02
49
12
81
74
54
82
65
77
85
6D
6F
Release 10
413
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 1.4.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
backward move in the proactive UICC session requested by the user
Coding:
BER-TLV:
81
03
01
24
00
82
02
82
81
83
01
11
TERMINAL RESPONSE: SELECT ITEM 1.4.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
backward move in the proactive UICC session requested by the user
Item identifier
Identifier of item chosen:
XX
Coding:
BER-TLV:
81
90
03
01
01
XX
24
00
82
02
82
81
83
01
11
01
10
TERMINAL RESPONSE: SELECT ITEM 1.4.2A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
proactive UICC session terminated by the user
Coding:
BER-TLV:
81
03
01
24
00
82
ETSI
02
82
81
83
Release 10
414
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 1.4.2B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
proactive UICC session terminated by the user
Item identifier
Identifier of item chosen:
XX
Coding:
BER-TLV:
81
90
03
01
01
XX
24
00
82
02
82
81
83
01
10
Expected Sequence 1.5 (SELECT ITEM, "Y", successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 1.5.1
Terminal → USER Present the items of "Y" under the
header of "The SIM shall supply a
set of items from which the user
may choose one. Each item
comprises a short identifier (used
to indicate the selection) and a text
string. Optionally the SIM may
include an alpha identifier. The
alpha identifier i".
USER → Terminal Select item "Y"
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 1.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: SELECT ITEM 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
Device identities
Source device:
Destination device:
Alpha identifier:
1
SELECT ITEM
"00"
UICC
Terminal
"The SIM shall supply a set of items from which the user may choose
one. Each item comprises a short identifier (used to indicate the
selection) and a text string. Optionally the SIM may include an alpha
identifier. The alpha identifier i"
ETSI
Release 10
415
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
"01"
"Y"
Coding:
BER-TLV:
D0
85
68
61
6D
68
61
65
20
20
69
74
74
6E
74
74
20
6C
61
2E
69
69
81
81
61
20
73
20
79
2E
63
73
66
6F
68
29
20
69
53
75
20
20
64
8F
FD
ED
6C
73
20
74
20
20
6F
68
69
20
65
20
73
6F
49
64
69
54
65
02
81
54
6C
65
66
68
63
45
6D
6F
65
69
20
61
74
6E
4D
65
64
68
6E
01
03
68
20
74
72
65
68
61
70
72
72
6E
73
6E
72
61
20
20
65
65
74
59
01
65
73
20
6F
20
6F
63
72
74
20
64
65
64
69
6C
6D
61
6E
20
69
24
20
75
6F
6D
75
6F
68
69
20
28
69
6C
20
6E
6C
61
6E
74
61
66
00
53
70
66
20
73
73
20
73
69
75
63
65
61
67
79
79
20
69
6C
69
82
49
70
20
77
65
65
69
65
64
73
61
63
20
2E
20
20
61
66
70
65
02
4D
6C
69
68
72
20
74
73
65
65
74
74
74
20
74
69
6C
69
68
72
81
20
79
74
69
20
6F
65
20
6E
64
65
69
65
4F
68
6E
70
65
61
20
82
73
20
65
63
6D
6E
6D
61
74
20
20
6F
78
70
65
63
68
72
20
83
01
00
TERMINAL RESPONSE: SELECT ITEM 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
81
90
03
01
01
01
24
00
82
ETSI
02
82
81
Release 10
416
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.6 (SELECT ITEM, Large menu, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 1.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 1.6.1
Terminal → USER Present the items of "1 Call
Forward Unconditional", "2 Call
Forward On User Busy", "3 Call
Forward On No Reply", "4 Call
Forward On User Not Reachable",
"5 Barring Of All Outgoing Calls",
"6 Barring Of All Outgoing Int
Calls" and "7 CLI Presentation"
under the header of
"0LargeMenu".
USER → Terminal Select item "5 Barring Of All
Outgoing Calls".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 1.6.1
PROACTIVE COMMAND: SELECT ITEM 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"0LargeMenu"
Item
Identifier of item:
Text string of item:
"FF"
"1 Call Forward Unconditional"
Identifier of item:
Text string of item:
"FE"
"2 Call Forward On User Busy"
Identifier of item:
Text string of item:
"FD"
"3 Call Forward On No Reply"
Identifier of item:
Text string of item:
"FC"
"4 Call Forward On User Not Reachable"
Identifier of item:
Text string of item:
"FB"
"5 Barring Of All Outgoing Calls"
Identifier of item:
Text string of item:
"FA"
"6 Barring Of All Outgoing Int Calls"
Identifier of item:
Text string of item:
"F9"
"7 CLI Presentation"
Item
Item
Item
Item
Item
Item
ETSI
Release 10
417
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
85
8F
72
69
43
20
79
6F
20
61
4F
52
35
20
67
42
6C
49
37
74
81
0A
1D
77
74
61
4F
8F
72
52
6C
6E
65
20
41
20
61
6C
6E
20
61
F3
30
FF
61
69
6C
6E
1B
77
65
6C
20
61
42
6C
43
72
20
74
43
74
81
4C
31
72
6F
6C
20
FD
61
70
20
55
63
61
6C
61
72
4F
20
4C
69
03
61
20
64
6E
20
55
33
72
6C
46
73
68
72
20
6C
69
75
43
49
6F
01
72
43
20
61
46
73
20
64
79
6F
65
61
72
4F
6C
6E
74
61
20
6E
24
67
61
55
6C
6F
65
43
20
8F
72
72
62
69
75
73
67
67
6C
50
00
65
6C
6E
8F
72
72
61
4F
25
77
20
6C
6E
74
8F
20
6F
6C
72
82
4D
6C
63
1C
77
20
6C
6E
FC
61
4E
65
67
67
24
4F
69
73
65
02
65
20
6F
FE
61
42
6C
20
34
72
6F
8F
20
6F
FA
66
6E
8F
73
81
6E
46
6E
32
72
75
20
4E
20
64
74
20
4F
69
36
20
67
13
65
82
75
6F
64
20
64
73
46
6F
43
20
20
FB
66
6E
20
41
20
F9
6E
83
01
00
TERMINAL RESPONSE: SELECT ITEM 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
FB
Coding:
BER-TLV:
81
90
03
01
01
FB
24
00
82
02
82
81
The following table details the test commands with relation to the tested features:
Proactive UICC Command
SELECT ITEM Number
1.1
1.2
1.3
1.4
1.5
1.6
Proactive UICC Command Facilities
Alpha Identifier Number of
Maximum
Length
items
length of item
14
4
6
10
30
8
10
7
43
11
2
3
236
1
1
10
7
37
ETSI
Release 10
418
27.22.4.9.1.5
ETSI TS 102 384 V10.3.0 (2015-08)
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1, 1.2, 1.3, 1.4, 1.5 and 1.6 (SELECT ITEM,
mandatory features).
27.22.4.9.2
SELECT ITEM (next action support)
27.22.4.9.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.2.2
Conformance Requirement
Same as clause 27.22.4.9.1.2.
27.22.4.9.2.3
Test purpose
To verify that the Terminal supports next action indicator mode.
27.22.4.9.2.4
Method of test
27.22.4.9.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.2.4.2
Procedure
Expected Sequence 2.1 (SELECT ITEM, next action indicator, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 2.1.1
Terminal → USER Display items of "Item 1", "Item 2"
and "Item 3" under the header of
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 2".
Comments
The Terminal may indicate to the user the
consequences of performing the selection of
an item.
The Terminal may indicate to the user the
consequences of performing the selection of
an item.
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 2.1.1
PROACTIVE COMMAND: SELECT ITEM 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
1
"Item 1"
ETSI
Release 10
419
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
2
"Item 2"
Identifier of item:
Text string of item:
3
"Item 3"
Item
Items next action indicator
Items list
"Send SM", "Set Up Call", "Provide Local Info."
Coding:
BER-TLV:
D0
0E
65
8F
49
39
54
63
07
74
81
6F
74
02
65
03
6F
8F
49
6D
01
6C
07
74
20
24
6B
01
65
33
00
69
49
6D
18
82
74
74
20
03
02
20
65
32
13
81
53
6D
8F
10
82
65
20
07
26
85
6C
31
03
83
01
00
TERMINAL RESPONSE: SELECT ITEM 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
27.22.4.9.2.5
81
90
03
01
01
02
24
00
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.9.3
27.22.4.9.3.1
SELECT ITEM (default item support)
Definition and applicability
See clause 3.2.2.
27.22.4.9.3.2
Conformance requirement
Same as clause 27.22.4.9.1.2.
27.22.4.9.3.3
Test purpose
To verify that the Terminal supports "default item" mode.
27.22.4.9.3.4
Method of test
27.22.4.9.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
ETSI
82
81
Release 10
420
ETSI TS 102 384 V10.3.0 (2015-08)
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.3.4.2
Procedure
Expected Sequence 3.1 (SELECT ITEM, default item, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 3.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 3.1.1
Terminal → USER Display items of "Item 1", "Item 2" If A.1/59 is supported, check that "Item 2" is
and "Item 3" under the header of
selected by default.
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 3.1.1
PROACTIVE COMMAND: SELECT ITEM 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Item
Identifier of item:
Text string of item:
Item identifier
Identifier of item chosen
03
"Item 3"
02
Coding:
BER-TLV:
D0
0E
65
8F
49
37
54
63
07
74
81
6F
74
02
65
03
6F
8F
49
6D
01
6C
07
74
20
24
6B
01
65
33
TERMINAL RESPONSE: SELECT ITEM 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
ETSI
00
69
49
6D
10
82
74
74
20
01
02
20
65
32
02
81
53
6D
8F
82
65
20
07
85
6C
31
03
Release 10
421
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
03
Coding:
BER-TLV:
27.22.4.9.3.5
81
90
03
01
01
03
24
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 3.1.
27.22.4.9.4
27.22.4.9.4.1
SELECT ITEM (help request support)
Definition and applicability
See clause 3.2.2.
27.22.4.9.4.2
Conformance requirement
Same as clause 27.22.4.9.1.2.
27.22.4.9.4.3
Test purpose
To verify that the Terminal supports "help request" for the command Select Item.
27.22.4.9.4.4
Method of test
27.22.4.9.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.4.4.2
Procedure
Expected Sequence 4.1 (SELECT ITEM, help request, successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 4.1.1
Terminal → UICC FETCH
Help information available.
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 4.1.1
Terminal → USER Display items of "Item 1", "Item 2"
and "Item 3" under the header of
"Toolkit Select".
USER → Terminal Navigate in the items until "Item 1".
USER → Terminal Select the Help Request on "Item
1" Menu entry
Terminal → UICC TERMINAL RESPONSE: SELECT Help information required by the user.
ITEM 4.1.1
ETSI
Release 10
422
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"80" help information available
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Identifier of item:
Text string of item:
03
"Item 3"
Item
Item
Coding:
BER-TLV:
D0
0E
65
8F
49
34
54
63
07
74
81
6F
74
02
65
03
6F
8F
49
6D
01
6C
07
74
20
24
6B
01
65
33
80
69
49
6D
82
74
74
20
02
20
65
32
81
53
6D
8F
82
65
20
07
85
6C
31
03
83
01
13
TERMINAL RESPONSE: SELECT ITEM 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"80"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Help information required by the user
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.4.5
81
90
03
01
01
01
24
80
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.1.
ETSI
82
81
Release 10
423
27.22.4.9.5
SELECT ITEM (icons support)
27.22.4.9.5.1
Definition and applicability
ETSI TS 102 384 V10.3.0 (2015-08)
See clause 3.2.2.
27.22.4.9.5.2
Conformance requirement
Same as clause 27.22.4.9.1.2 and ETSI TS 102 223 [1], clauses 8.31 and 8.32.
27.22.4.9.5.3
Test purpose
To verify that the Terminal displays icons with the command Select Item.
27.22.4.9.5.4
Method of test
27.22.4.9.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.5.4.2
Procedure
Expected Sequence 5.1A (SELECT ITEM, BASIC ICON NOT SELF EXPLANATORY, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 5.1.1
Terminal → USER Display items of "Item 1", "Item 2" Verify icons are displayed in the alpha
and "Item 3" under the header of
identifier and in the 3 items.
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 5.1.1 A
PROACTIVE COMMAND: SELECT ITEM 5.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Identifier of item:
Text string of item:
03
"Item 3"
Item
Item
ETSI
Release 10
424
ETSI TS 102 384 V10.3.0 (2015-08)
Icon Identifier:
Icon qualifier:
Icon Identifier:
"01" (icon is not self-explanatory)
record 1 in EF(IMG)
Item icon identifier list:
Icon qualifier:
Icon Identifier:
"01" (icon is not self-explanatory)
record 5 in EF(IMG) , record 5 in EF(IMG), record 5 in EF(IMG)
Coding:
BER-TLV:
D0
0E
65
8F
49
01
3E
54
63
07
74
05
81
6F
74
02
65
05
03
6F
8F
49
6D
05
01
6C
07
74
20
24
6B
01
65
33
00
69
49
6D
9E
82
74
74
20
02
02
20
65
32
01
81
53
6D
8F
01
82
65
20
07
9F
85
6C
31
03
04
83
01
00
TERMINAL RESPONSE: SELECT ITEM 5.1.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
81
90
03
01
01
01
24
00
82
02
82
81
Expected Sequence 5.1B (SELECT ITEM, BASIC ICON NOT SELF EXPLANATORY, requested icon could
not be displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 5.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 5.1.1
Terminal → USER Display items of "Item 1", "Item 2"
and "Item 3" under the header of
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 1" under the header "Toolkit
Select".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 5.1.1 B
ETSI
Comments
Verify that either for the header or for each of
the items no icon is displayed.
Command performed successfully, but
requested icon could not be displayed.
Release 10
425
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 5.1.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
81
90
03
01
01
01
24
00
82
02
82
81
83
01
04
Expected Sequence 5.2A (SELECT ITEM, BASIC ICON SELF EXPLANATORY, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 5.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 5.2.1
Terminal → USER Display items of "Item 1", "Item 2" Verify icons are displayed without text as
and "Item 3" under the header of
alpha id and for the all 3 items.
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 5.2.1 A
PROACTIVE COMMAND: SELECT ITEM 5.2.1.
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
ETSI
Release 10
426
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
03
"Item 3"
Icon Identifier:
Icon qualifier:
Icon Identifier:
"00" (icon is self-explanatory)
record 1 in EF(IMG)
Item icon identifier list:
Icon qualifier:
Icon Identifier:
"00" (icon is self-explanatory)
record 5 in EF(IMG) , record 5 in EF(IMG), record 5 in EF(IMG)
Coding:
BER-TLV:
D0
0E
65
8F
49
00
3E
54
63
07
74
05
81
6F
74
02
65
05
03
6F
8F
49
6D
05
01
6C
07
74
20
24
6B
01
65
33
00
69
49
6D
9E
82
74
74
20
02
02
20
65
32
00
81
53
6D
8F
01
82
65
20
07
9F
85
6C
31
03
04
83
01
00
TERMINAL RESPONSE: SELECT ITEM 5.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
81
90
03
01
01
01
24
00
82
02
82
81
Expected Sequence 5.2B (SELECT ITEM, BASIC ICON SELF EXPLANATORY, requested icon could not be
displayed)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 5.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 5.2.1
Terminal → USER Display items of "Item 1", "Item 2"
and "Item 3" under the header of
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 1" under the header 'Toolkit
Select'.
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 5.2.1B
ETSI
Comments
Verify that either for the header or for each of
the items no icon is displayed.
Command performed successfully but
requested icon could not be displayed.
Release 10
427
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 5.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully but requested icon could not be
displayed
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.5.5
81
90
03
01
01
01
24
00
82
02
82
81
83
01
04
Test requirement
The Terminal shall operate in the manner defined in expected sequences 5.1A to 5.2B.
27.22.4.9.6
SELECT ITEM (presentation style)
27.22.4.9.6.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.6.2
Conformance requirement
Same as clause 27.22.4.9.1.2.
27.22.4.9.6.3
Test purpose
To verify that the Terminal supports the "presentation style" with the command Select Item.
27.22.4.9.6.4
Method of test
27.22.4.9.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.6.4.2
Procedure
Expected Sequence 6.1 (SELECT ITEM, PRESENTATION AS A CHOICE OF NAVIGATION OPTIONS,
successful)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 6.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 6.1.1
ETSI
Comments
Release 10
Step
4
5
6
428
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → USER Display items of "Item 1", "Item 2" Verify if presentation style appears.
and "Item 3" under the header of
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 6.1.1
PROACTIVE COMMAND: SELECT ITEM 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"03" (presentation as a choice of navigation options)
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Identifier of item:
Text string of item:
03
"Item 3"
Item
Item
Coding:
BER-TLV:
D0
0E
65
8F
49
34
54
63
07
74
81
6F
74
02
65
03
6F
8F
49
6D
01
6C
07
74
20
24
6B
01
65
33
03
69
49
6D
82
74
74
20
02
20
65
32
81
53
6D
8F
82
65
20
07
TERMINAL RESPONSE: SELECT ITEM 6.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"03" (presentation as a choice of navigation options)
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Item identifier
Identifier of item chosen:
Command performed successfully
01
ETSI
85
6C
31
03
Release 10
429
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
90
03
01
01
01
24
03
82
02
82
81
83
01
00
Expected Sequence 6.2 (SELECT ITEM, PRESENTATION AS A CHOICE OF DATA VALUES, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 6.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 6.2.1
Terminal → USER Display items of "Item 1", "Item 2" Verify if presentation style appears.
and "Item 3" under the header of
"Toolkit Select".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 6.2.1
PROACTIVE COMMAND: SELECT ITEM 6.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"01" (presentation as a choice of data values)
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Identifier of item:
Text string of item:
03
"Item 3"
Item
Item
Coding:
BER-TLV:
D0
0E
65
8F
49
34
54
63
07
74
81
6F
74
02
65
03
6F
8F
49
6D
01
6C
07
74
20
24
6B
01
65
33
01
69
49
6D
82
74
74
20
02
20
65
32
81
53
6D
8F
TERMINAL RESPONSE: SELECT ITEM 6.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"01"(presentation as a choice of data values)
ETSI
82
65
20
07
85
6C
31
03
Release 10
430
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.6.5
81
90
03
01
01
01
24
01
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 6.1 and 6.2.
27.22.4.9.7
27.22.4.9.7.1
SELECT ITEM (soft keys support)
Definition and applicability
See clause 3.2.2.
27.22.4.9.7.2
Conformance requirement
Same as clause 27.22.4.9.1.2.
27.22.4.9.7.3
Test purpose
To verify that the Terminal supports the "soft keys" with the command Select Item.
27.22.4.9.7.4
Method of test
27.22.4.9.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.7.4.2
Procedure
Expected Sequence 7.1 (SELECT ITEM, SELECTING USING SOFT KEYS PREFERRED, successful,
successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 7.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 7.1.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit
Select".
USER → Terminal Navigate in the items, then select Verify that we can choose an item through
"Item 1".
soft keys.
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 7.1.1
ETSI
Release 10
431
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"04" (selection using soft keys preferred)
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Coding:
BER-TLV:
D0
0E
65
8F
2B
54
63
07
81
6F
74
02
03
6F
8F
49
01
6C
07
74
24
6B
01
65
04
69
49
6D
82
74
74
20
02
20
65
32
81
53
6D
82
65
20
85
6C
31
01
00
TERMINAL RESPONSE: SELECT ITEM 7.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"04" (selection using soft keys preferred)
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.7.5
81
90
03
01
01
01
24
04
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 7.1.
27.22.4.9.8
27.22.4.9.8.1
SELECT ITEM (Support of "No response from user")
Definition and applicability
See clause 3.2.2.
ETSI
83
Release 10
432
27.22.4.9.8.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
Same as clause 27.22.4.9.1.2.
27.22.4.9.8.3
Test purpose
To verify that after a period of user inactivity the Terminal returns a "No response from user" result value in the
TERMINAL RESPONSE command sent to the UICC.
27.22.4.9.8.4
Method of test
27.22.4.9.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal Manufacturer shall have defined the "no response from user" period of time as declared in table A.2/4.
The UICC Simulator shall be set to that period of time.
27.22.4.9.8.4.2
Procedure
Expected Sequence 8.1 (SELECT ITEM, no response from user)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 8.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 8.1.1
Terminal → USER Display items of "Item 1", "Item 2"
and "Item 3" under the header of
"<TIME-OUT>".
USER
Waiting and no completion
Terminal → UICC TERMINAL RESPONSE: SELECT No response from user within 5 s after the end
ITEM 8.1.1
of that defined period of time.
USER
Check if the delay of TERMINAL
RESPONSE is reasonable or not
PROACTIVE COMMAND: SELECT ITEM 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"<TIME-OUT>"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Identifier of item:
Text string of item:
03
"Item 3"
Item
Item
ETSI
Release 10
433
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0A
07
74
20
30
3C
01
65
33
81
54
49
6D
03
49
74
20
01
4D
65
32
24
45
6D
8F
00
2D
20
07
82
4F
31
03
02
55
8F
49
81
54
07
74
82
3E
02
65
85
8F
49
6D
82
81
83
01
12
TERMINAL RESPONSE: SELECT ITEM 8.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
No response from user
Coding:
BER-TLV:
27.22.4.9.8.5
81
03
01
24
00
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 8.1.
27.22.4.9.9
SELECT ITEM (Support of Text Attribute)
27.22.4.9.9.1
SELECT ITEM (Support of Text Attribute - Left Alignment)
27.22.4.9.9.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.1.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.1.3
Test purpose
To verify that the Terminal displays text formatted according to the left alignment text attribute configuration within the
command Select Item.
27.22.4.9.9.1.4
Method of test
27.22.4.9.9.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
434
27.22.4.9.9.1.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 9.1 (SELECT ITEM, Text Attribute - Left Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.1.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.1.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
Comments
Verify the text attribute of the alpha id and
each item are displayed with left alignment.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed without left
alignment. Remark: If left alignment is the
Terminal's default alignment as declared in
table A.2/10, no alignment change will take
place.
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 9.1.1
PROACTIVE COMMAND: SELECT ITEM 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
435
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
31
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
32
B4
85
6C
6D
D0
00
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
34
85
6C
6D
PROACTIVE COMMAND: SELECT ITEM 9.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
33
81
6F
74
8F
03
6F
20
07
01
6C
32
02
24
6B
8F
49
TERMINAL RESPONSE: SELECT ITEM 9.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
ETSI
Release 10
436
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.1.5
81
90
03
01
01
01
24
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.1.
27.22.4.9.9.2
SELECT ITEM (Support of Text Attribute - Center Alignment)
27.22.4.9.9.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.2.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.2.3
Test purpose
To verify that the Terminal displays text formatted according to the center alignment text attribute configuration within
the command Select Item.
27.22.4.9.9.2.4
Method of test
27.22.4.9.9.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.2.4.2
Procedure
Expected Sequence 9.2 (SELECT ITEM, Text Attribute - Center Alignment)
Step
1
2
3
4
5
6
7
8
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.2.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.2.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.2.2
Terminal → UICC FETCH
ETSI
Comments
Verify the text attribute of the alpha id and
each item are displayed with center
alignment.
Command performed successfully.
Release 10
Step
9
10
11
12
437
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.2.2
Terminal → USER Display items of "Item 3", "Item 4" Verify the text attribute of the alpha id and
under the header of "Toolkit Select each item are displayed without center
2".
alignment. Remark: If center alignment is the
Terminal's default alignment as declared in
table A.2/10, no alignment change will take
place.
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 9.2.1
PROACTIVE COMMAND: SELECT ITEM 9.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Center Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Center Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Center Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
438
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
01
81
6F
74
8F
10
B4
03
6F
20
07
01
01
6C
31
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
01
82
65
65
32
B4
85
6C
6D
D0
00
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
34
85
6C
6D
83
01
00
PROACTIVE COMMAND: SELECT ITEM 9.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
33
81
6F
74
8F
03
6F
20
07
01
6C
32
02
24
6B
8F
49
TERMINAL RESPONSE: SELECT ITEM 9.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
81
90
03
01
01
01
24
00
82
ETSI
02
82
81
Release 10
439
27.22.4.9.9.2.5
ETSI TS 102 384 V10.3.0 (2015-08)
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.2.
27.22.4.9.9.3
SELECT ITEM (Support of Text Attribute - Right Alignment)
27.22.4.9.9.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.3.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.3.3
Test purpose
To verify that the Terminal displays text formatted according to the right alignment text attribute configuration within
the command Select Item.
27.22.4.9.9.3.4
Method of test
27.22.4.9.9.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.3.4.2
Procedure
Expected Sequence 9.3 (SELECT ITEM, Text Attribute - Right Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.3.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.3.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.3.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
Comments
Verify the text attribute of the alpha id and
each item are displayed with right alignment.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed without right
alignment. Remark: If right alignment is the
Terminal's default alignment as declared in
table A.2/10, no alignment change will take
place.
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 9.3.1
ETSI
Release 10
440
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 9.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
02
81
6F
74
8F
10
B4
03
6F
20
07
02
01
6C
31
02
B4
24
6B
8F
49
D1
PROACTIVE COMMAND: SELECT ITEM 9.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
ETSI
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
02
82
65
65
32
B4
85
6C
6D
D0
00
Release 10
441
Device identities
Source device:
Destination device:
Alpha identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
02
Item
Text string of item:
"Item 4"
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
33
81
6F
74
8F
03
6F
20
07
01
6C
32
02
24
6B
8F
49
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
34
85
6C
6D
83
01
00
TERMINAL RESPONSE: SELECT ITEM 9.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.3.5
81
90
03
01
01
01
24
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.3.
27.22.4.9.9.4
SELECT ITEM (Support of Text Attribute - Large Font Size)
27.22.4.9.9.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.4.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.4.3
Test purpose
To verify that the Terminal displays text formatted according to the large font size text attribute configuration within the
command Select Item.
ETSI
Release 10
442
27.22.4.9.9.4.4
Method of test
27.22.4.9.9.4.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.4.4.2
Procedure
Expected Sequence 9.4 (SELECT ITEM, Text Attribute - Large Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.4.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.4.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.4.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.4.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.4.3
Terminal → USER Display items of "Item 5", "Item 6"
under the header of "Toolkit Select
3".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.4.1
ETSI
Comments
Verify the text attribute of the alpha id and
each item are displayed with large font size.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with normal font size.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with large font size.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with normal font size.
Command performed successfully.
Release 10
443
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 9.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
04
81
6F
74
8F
10
B4
03
6F
20
07
04
01
6C
31
02
B4
24
6B
8F
49
D1
PROACTIVE COMMAND: SELECT ITEM 9.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
ETSI
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
04
82
65
65
32
B4
85
6C
6D
D0
00
Release 10
444
Device identities
Source device:
Destination device:
Alpha identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
33
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
32
02
B4
24
6B
8F
49
D1
PROACTIVE COMMAND: SELECT ITEM 9.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 3"
Item
Identifier of item:
Text string of item:
01
"Item 5"
ETSI
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
34
B4
85
6C
6D
D0
00
Release 10
445
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
02
"Item 6"
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
35
81
6F
74
8F
03
6F
20
07
01
6C
33
02
24
6B
8F
49
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
36
85
6C
6D
83
01
00
TERMINAL RESPONSE: SELECT ITEM 9.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.4.5
81
90
03
01
01
01
24
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.4.
27.22.4.9.9.5
SELECT ITEM (Support of Text Attribute - Small Font Size)
27.22.4.9.9.5.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.5.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.5.3
Test purpose
To verify that the Terminal displays text formatted according to the small font size text attribute configuration within
the command Select Item.
27.22.4.9.9.5.4
Method of test
27.22.4.9.9.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
446
27.22.4.9.9.5.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 9.5 (SELECT ITEM, Text Attribute - Small Font Size)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.5.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.5.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.5.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.5.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.5.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.5.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.5.3
Terminal → USER Display items of "Item 5", "Item 6"
under the header of "Toolkit Select
3".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.5.1
PROACTIVE COMMAND: SELECT ITEM 9.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
ETSI
Comments
Verify the text attribute of the alpha id and
each item are displayed with small font size.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with normal font size.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with small font size.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with normal font size.
Command performed successfully.
Release 10
447
Device identities
Source device:
Destination device:
Alpha identifier:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
08
81
6F
74
8F
10
B4
03
6F
20
07
08
01
6C
31
02
B4
24
6B
8F
49
D1
PROACTIVE COMMAND: SELECT ITEM 9.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
ETSI
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
08
82
65
65
32
B4
85
6C
6D
D0
00
Release 10
448
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
02
"Item 4"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
33
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
32
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
34
B4
85
6C
6D
D0
00
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
36
85
6C
6D
PROACTIVE COMMAND: SELECT ITEM 9.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 3"
Item
Identifier of item:
Text string of item:
01
"Item 5"
Identifier of item:
Text string of item:
02
"Item 6"
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
35
81
6F
74
8F
03
6F
20
07
01
6C
33
02
24
6B
8F
49
ETSI
Release 10
449
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 9.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.5.5
81
90
03
01
01
01
24
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.5.
27.22.4.9.9.6
SELECT ITEM (Support of Text Attribute - Bold On)
27.22.4.9.9.6.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.6.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.6.3
Test purpose
To verify that the Terminal displays text formatted according to the bold text attribute configuration within the
command Select Item.
27.22.4.9.9.6.4
Method of test
27.22.4.9.9.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.6.4.2
Procedure
Expected Sequence 9.6 (SELECT ITEM, Text Attribute - Bold On)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.6.1
ETSI
Comments
Release 10
Step
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
450
Direction
Message/Action
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.6.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.6.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.6.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.6.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.6.3
Terminal → USER Display items of "Item 5", "Item 6"
under the header of "Toolkit Select
3".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.6.1
PROACTIVE COMMAND: SELECT ITEM 9.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Verify the text attribute of the alpha id and
each item are displayed with bold on.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with bold off.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with bold on.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with bold off.
Command performed successfully.
Release 10
451
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
16
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
10
81
6F
74
8F
10
B4
03
6F
20
07
10
01
6C
31
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
10
82
65
65
32
B4
85
6C
6D
D0
00
PROACTIVE COMMAND: SELECT ITEM 9.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Item Text Attribute List
Text Attribute List:
Item #1
ETSI
Release 10
452
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
33
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
32
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
34
B4
85
6C
6D
D0
00
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
36
85
6C
6D
PROACTIVE COMMAND: SELECT ITEM 9.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 3"
Item
Identifier of item:
Text string of item:
01
"Item 5"
Identifier of item:
Text string of item:
02
"Item 6"
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
35
81
6F
74
8F
03
6F
20
07
01
6C
33
02
24
6B
8F
49
TERMINAL RESPONSE: SELECT ITEM 9.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
453
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.6.5
81
90
03
01
01
01
24
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.6.
27.22.4.9.9.7
SELECT ITEM (Support of Text Attribute - Italic On)
27.22.4.9.9.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.7.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.7.3
Test purpose
To verify that the Terminal displays text formatted according to the italic text attribute configuration within the
command Select Item.
27.22.4.9.9.7.4
Method of test
27.22.4.9.9.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.7.4.2
Procedure
Expected Sequence 9.7 (SELECT ITEM, Text Attribute - Italic On)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.7.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.7.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.7.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
ETSI
Comments
Verify the text attribute of the alpha id and
each item are displayed with italic on.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with italic off.
Release 10
Step
11
12
13
14
15
16
17
18
19
20
21
22
23
24
454
Direction
Message/Action
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.7.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.7.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.7.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.7.3
Terminal → USER Display items of "Item 5", "Item 6"
under the header of "Toolkit Select
3".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.7.1
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with italic on.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with italic off.
Command performed successfully.
PROACTIVE COMMAND: SELECT ITEM 9.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
0
16
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
ETSI
Release 10
455
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
20
81
6F
74
8F
10
B4
03
6F
20
07
20
01
6C
31
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
20
82
65
65
32
B4
85
6C
6D
D0
00
PROACTIVE COMMAND: SELECT ITEM 9.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
456
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
33
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
32
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
34
B4
85
6C
6D
D0
00
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
36
85
6C
6D
83
01
00
PROACTIVE COMMAND: SELECT ITEM 9.7.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 3"
Item
Identifier of item:
Text string of item:
01
"Item 5"
Identifier of item:
Text string of item:
02
"Item 6"
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
35
81
6F
74
8F
03
6F
20
07
01
6C
33
02
24
6B
8F
49
TERMINAL RESPONSE: SELECT ITEM 9.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
81
90
03
01
01
01
24
00
82
ETSI
02
82
81
Release 10
457
27.22.4.9.9.7.5
ETSI TS 102 384 V10.3.0 (2015-08)
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.7.
27.22.4.9.9.8
SELECT ITEM (Support of Text Attribute - Underline On)
27.22.4.9.9.8.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.8.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.8.3
Test purpose
To verify that the Terminal displays text formatted according to the underline text attribute configuration within the
command Select Item.
27.22.4.9.9.8.4
Method of test
27.22.4.9.9.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.8.4.2
Procedure
Expected Sequence 9.8 (SELECT ITEM, Text Attribute - Underline On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.8.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.8.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.8.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.8.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
ETSI
Comments
Verify the text attribute of the alpha id and
each item are displayed with underline on.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with underline off.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with underline on.
Release 10
Step
17
18
19
20
21
22
23
24
458
Direction
Message/Action
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.8.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.8.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.8.3
Terminal → USER Display items of "Item 5", "Item 6"
under the header of "Toolkit Select
3".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.8.1
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with underline off.
Command performed successfully.
PROACTIVE COMMAND: SELECT ITEM 9.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
459
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
40
81
6F
74
8F
10
B4
03
6F
20
07
40
01
6C
31
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
40
82
65
65
32
B4
85
6C
6D
D0
00
PROACTIVE COMMAND: SELECT ITEM 9.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
33
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
32
02
B4
24
6B
8F
49
D1
ETSI
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
34
B4
85
6C
6D
D0
00
Release 10
460
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 9.8.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 3"
Item
Identifier of item:
Text string of item:
01
"Item 5"
Identifier of item:
Text string of item:
02
"Item 6"
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
35
81
6F
74
8F
03
6F
20
07
01
6C
33
02
24
6B
8F
49
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
36
85
6C
6D
83
01
00
TERMINAL RESPONSE: SELECT ITEM 9.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.8.5
81
90
03
01
01
01
24
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.8.
27.22.4.9.9.9
SELECT ITEM (Support of Text Attribute - Strikethrough On)
27.22.4.9.9.9.1
Definition and applicability
See clause 3.2.2.
ETSI
Release 10
461
27.22.4.9.9.9.2
ETSI TS 102 384 V10.3.0 (2015-08)
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.9.3
Test purpose
To verify that the Terminal displays text formatted according to the strikethrough text attribute configuration within the
command Select Item.
27.22.4.9.9.9.4
Method of test
27.22.4.9.9.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.9.4.2
Procedure
Expected Sequence 9.9 (SELECT ITEM, Text Attribute - Strikethrough On)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.9.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.9.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.9.2
Terminal → USER Display items of "Item 3", "Item 4"
under the header of "Toolkit Select
2".
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.9.1
Terminal → USER Display items of "Item 1", "Item 2"
under the header of "Toolkit Select
1".
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT
ITEM 9.9.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.9.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.9.3
ETSI
Comments
Verify the text attribute of the alpha id and
each item are displayed with strikethrough on.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with strikethrough off.
Command performed successfully.
Verify the text attribute of the alpha id and
each item are displayed with strikethrough on.
Command performed successfully.
Release 10
Step
22
462
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → USER Display items of "Item 5", "Item 6" Verify the text attribute of the alpha id and
under the header of "Toolkit Select each item are displayed with strikethrough off.
3".
USER → Terminal Navigate in the items, then select
"Item 5".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 9.9.1
23
24
PROACTIVE COMMAND: SELECT ITEM 9.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough On
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
80
81
6F
74
8F
10
B4
03
6F
20
07
80
01
6C
31
02
B4
24
6B
8F
49
D1
ETSI
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
80
82
65
65
32
B4
85
6C
6D
D0
00
Release 10
463
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 9.9.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
33
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
32
02
B4
24
6B
8F
49
D1
PROACTIVE COMMAND: SELECT ITEM 9.9.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
UICC
ETSI
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
34
B4
85
6C
6D
D0
00
Release 10
464
Destination device:
Alpha identifier:
Terminal
"Toolkit Select 3"
Identifier of item:
Text string of item:
01
"Item 5"
Identifier of item:
Text string of item:
02
"Item 6"
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
35
81
6F
74
8F
03
6F
20
07
01
6C
33
02
24
6B
8F
49
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
36
85
6C
6D
83
01
00
TERMINAL RESPONSE: SELECT ITEM 9.9.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.9.5
81
90
03
01
01
01
24
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.9.
27.22.4.9.9.10
SELECT ITEM (Support of Text Attribute - Foreground and Background Colour)
27.22.4.9.9.10.1
Definition and applicability
See clause 3.2.2.
27.22.4.9.9.10.2
Conformance requirement
Requirements are the same as in clause 27.22.4.9.1.2, with an additional one:
•
ETSI TS 102 223 [1], clauses 6.5.4, 8.70 and 8.71.
27.22.4.9.9.10.3
Test purpose
To verify that the Terminal displays text formatted according to the foreground and background colour text attribute
configuration within the command Select Item.
ETSI
Release 10
465
27.22.4.9.9.10.4
Method of test
27.22.4.9.9.10.4.1
Initial conditions
ETSI TS 102 384 V10.3.0 (2015-08)
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.9.10.4.2
Procedure
Expected Sequence 9.10 (SELECT ITEM, Text Attribute - Foreground and Background Colour)
Step
1
2
3
4
5
6
7
8
9
10
11
12
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.10.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.10.1
Terminal → USER Display items of "Item 1", "Item 2" Verify the text attribute of the alpha id and
under the header of "Toolkit Select each item are displayed with foreground and
1".
background colour according to the
configuration.
USER → Terminal Navigate in the items, then select
"Item 1".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 9.10.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 9.10.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 9.10.2
Terminal → USER Display items of "Item 3", "Item 4" Verify the text attribute of the alpha id and
under the header of "Toolkit Select each item are displayed with Terminal's
2".
default foreground and background colour.
USER → Terminal Navigate in the items, then select
"Item 3".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 9.10.1
PROACTIVE COMMAND: SELECT ITEM 9.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 1"
Item
Identifier of item:
Text string of item:
01
"Item 1"
Identifier of item:
Text string of item:
02
"Item 2"
Item
Text Attribute
Formatting position:
Formatting length:
0
16
ETSI
Release 10
466
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item Text Attribute List
Text Attribute List:
Item #1
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Item #2
Formatting position:
Formatting length:
Formatting mode:
0
6
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
10
65
20
04
06
3D
54
63
31
00
00
81
6F
74
8F
10
B4
03
6F
20
07
00
01
6C
31
02
B4
24
6B
8F
49
D1
00
69
07
74
08
82
74
01
65
00
02
20
49
6D
06
81
53
74
20
00
82
65
65
32
B4
85
6C
6D
D0
00
00
69
07
74
82
74
01
65
02
20
49
6D
81
53
74
20
82
65
65
34
85
6C
6D
PROACTIVE COMMAND: SELECT ITEM 9.10.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"Toolkit Select 2"
Item
Identifier of item:
Text string of item:
01
"Item 3"
Identifier of item:
Text string of item:
02
"Item 4"
Item
Coding:
BER-TLV:
D0
10
65
20
2D
54
63
33
81
6F
74
8F
03
6F
20
07
01
6C
32
02
24
6B
8F
49
ETSI
Release 10
467
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 9.10.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
01
Coding:
BER-TLV:
27.22.4.9.9.10.5
81
90
03
01
01
01
24
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 9.10.
27.22.4.9.10
27.22.4.9.10.1
SELECT ITEM (UCS2 display in Cyrillic)
Definition and applicability
See clause 3.2.2.
27.22.4.9.10.2
Conformance requirement
The Terminal shall support the Proactive UICC: Select Item facility as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5, 6.4.9, 6.6.8, 6.8, 8.6, 8.7, 8.2, 8.9, 9.4 and 10.
27.22.4.9.10.3
Test purpose
To verify that the Terminal correctly presents the set of items in UCS2 coding contained in the SELECT ITEM
proactive UICC command, and returns a TERMINAL RESPONSE command to the UICC with the identifier of the
item chosen.
To verify that the Terminal allows a SELECT ITEM proactive UICC command within the maximum 255 byte
BER-TLV boundary.
To verify that the Terminal returns a TERMINAL RESPONSE with "Proactive UICC application session terminated by
the user", if the user has indicated the need to end the proactive UICC session.
To verify that the Terminal returns a TERMINAL RESPONSE with "Backwards move in the proactive UICC
application session requested by the user", if the user has indicated the need to go backwards in the proactive UICC
application session.
27.22.4.9.10.4
Method of test
27.22.4.9.10.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
468
27.22.4.9.10.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 10.1 (SELECT ITEM with UCS2 in Cyrillic characters, 0x80 UCS2 coding, successful)
Step
1
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 10.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 10.1.1
Terminal → USER Display items of
"ЗДРАВСТВУЙТЕ": "Hello" in Russian.
"ЗДРАВСТВУЙТЕ1",
"ЗДРАВСТВУЙТЕ2" and
"ЗДРАВСТВУЙТЕ3" under the
header of "ЗДРАВСТВУЙТЕ".
USER → Terminal Select "ЗДРАВСТВУЙТЕ2"
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 10.1.1
2
3
4
5
6
PROACTIVE COMMAND: SELECT ITEM 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"ЗДРАВСТВУЙТЕ"
Item
Identifier of item:
Text string of item:
1
"ЗДРАВСТВУЙТЕ1"
Identifier of item:
Text string of item:
2
"ЗДРАВСТВУЙТЕ2"
Identifier of item:
Text string of item:
3
"ЗДРАВСТВУЙТЕ3"
Item
Item
Coding:
BER-TLV:
D0
19
04
04
04
04
04
04
00
04
04
7E
80
21
15
10
19
17
22
32
10
19
81
04
04
8F
04
04
04
04
8F
04
04
03
17
22
1C
12
22
14
12
1C
12
22
01
04
04
01
04
04
04
04
03
04
04
24
14
12
80
21
15
20
23
80
21
15
ETSI
00
04
04
04
04
00
04
04
04
04
00
82
20
23
17
22
31
10
19
17
22
33
02
04
04
04
04
8F
04
04
04
04
81
10
19
14
12
1C
12
22
14
12
82
04
04
04
04
02
04
04
04
04
85
12
22
20
23
80
21
15
20
23
Release 10
469
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 10.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
81
90
03
01
01
02
24
00
82
02
82
81
83
01
00
Expected Sequence 10.2 (SELECT ITEM with UCS2 in Cyrillic characters, 0x81 UCS2 coding, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 10.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 10.2.1
Terminal → USER Display items of
"ЗДРАВСТВУЙТЕ": "Hello" in Russian.
"ЗДРАВСТВУЙТЕ1",
"ЗДРАВСТВУЙТЕ2" and
"ЗДРАВСТВУЙТЕ3" under the
header of "ЗДРАВСТВУЙТЕ".
USER → Terminal Select "ЗДРАВСТВУЙТЕ2".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 10.2.1
PROACTIVE COMMAND: SELECT ITEM 10.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"ЗДРАВСТВУЙТЕ"
Item
Identifier of item:
Text string of item:
1
"ЗДРАВСТВУЙТЕ1"
Identifier of item:
Text string of item:
2
"ЗДРАВСТВУЙТЕ2"
Item
ETSI
Release 10
470
ETSI TS 102 384 V10.3.0 (2015-08)
Item
Identifier of item:
Text string of item:
3
"ЗДРАВСТВУЙТЕ3"
Coding:
BER-TLV:
D0
0F
A3
A0
11
92
97
33
53
81
99
90
02
A3
94
81
0C
A2
92
81
99
A0
03
08
95
A1
0D
A2
90
01
97
8F
A2
08
95
92
24
94
11
92
97
32
A1
00
A0
01
A3
94
8F
A2
82
90
81
99
A0
11
92
02
92
0D
A2
90
03
A3
81
A1
08
95
92
81
99
82
A2
97
31
A1
0D
A2
85
92
94
8F
A2
08
95
83
01
00
TERMINAL RESPONSE: SELECT ITEM 10.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
81
90
03
01
01
02
24
00
82
02
82
81
Expected Sequence 10.3 (SELECT ITEM with UCS2 in Cyrillic characters, 0x82 UCS2 coding, successful)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 10.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 10.3.1
Terminal → USER Display items of
"ЗДРАВСТВУЙТЕ ": "Hello" in Russian.
"ЗДРАВСТВУЙТЕ1",
"ЗДРАВСТВУЙТЕ2" and
"ЗДРАВСТВУЙТЕ3" under the
header of "ЗДРАВСТВУЙТЕ".
USER → Terminal Select "ЗДРАВСТВУЙТЕ2"
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 10.2.1
ETSI
Release 10
471
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 10.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"ЗДРАВСТВУЙТЕ"
Item
Identifier of item:
Text string of item:
1
"ЗДРАВСТВУЙТЕ1"
Identifier of item:
Text string of item:
2
"ЗДРАВСТВУЙТЕ2"
Identifier of item:
Text string of item:
3
"ЗДРАВСТВУЙТЕ3"
Item
Item
Coding:
BER-TLV:
D0
10
82
87
31
82
82
93
57
82
93
84
8F
91
0D
89
81
0C
89
90
12
92
04
92
03
04
92
80
02
82
10
85
01
10
85
82
82
93
87
33
24
87
8F
91
0D
89
84
00
84
12
92
04
92
90
82
90
01
82
10
85
80
02
80
82
93
87
32
82
81
82
0D
89
84
8F
91
82
91
04
92
90
12
92
85
92
10
85
80
03
82
83
01
00
TERMINAL RESPONSE: SELECT ITEM 10.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
27.22.4.9.10.5
81
90
03
01
01
02
24
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequences 10.1 to 10.3.
ETSI
Release 10
472
27.22.4.9.11
27.22.4.9.11.1
ETSI TS 102 384 V10.3.0 (2015-08)
SELECT ITEM (UCS2 display in Chinese)
Definition and applicability
See clause 3.2.2.
27.22.4.9.11.2
Conformance requirement
The Terminal shall support the Proactive UICC: Select Item facility as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5, 6.4.9, 6.6.8, 6.8, 8.6, 8.7, 8.2, 8.9, 9.4 and 10.
27.22.4.9.11.3
Test purpose
To verify that the Terminal correctly presents the set of items in UCS2 coding contained in the SELECT ITEM
proactive UICC command, and returns a TERMINAL RESPONSE command to the UICC with the identifier of the
item chosen.
To verify that the Terminal allows a SELECT ITEM proactive UICC command within the maximum 255 byte
BER-TLV boundary.
To verify that the Terminal returns a TERMINAL RESPONSE with "Proactive UICC application session terminated by
the user", if the user has indicated the need to end the proactive UICC session.
To verify that the Terminal returns a TERMINAL RESPONSE with "Backwards move in the proactive UICC
application session requested by the user", if the user has indicated the need to go backwards in the proactive UICC
application session.
27.22.4.9.11.4
Method of test
27.22.4.9.11.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.11.4.2
Procedure
Expected Sequence 11.1 (SELECT ITEM with UCS2 in Chinese Characters, successful)
Step
1
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 11.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 11.1.1
Terminal → USER Display items of "
", "
", "
5
USER → Terminal
6
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully
ITEM 11.1.1
2
3
Comments
项目一 项目二 工具箱选择": "Toolkit Select" in Chinese.
"项目三" and "项目四" under the
"项目一": "Item 1" in Chinese.
header of "工具箱选择".
"项目二": "Item 2" in Chinese.
"项目三": "Item 3" in Chinese.
"项目四": "Item 4" in Chinese.
Select "项目二".
ETSI
Release 10
473
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 11.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
UICC
Terminal
Alpha identifier:
"
工具箱选择"
Item
Identifier of item:
1
Text string of item:
"
Item
项目一"
Identifier of item:
2
Text string of item:
"
Identifier of item:
3
Text string of item:
"
Identifier of item:
4
Text string of item:
"
Item
项目二"
项目三"
Item
项目四"
Coding:
BER-TLV:
D0
0B
8F
02
98
76
3E
80
08
80
79
EE
81
5D
01
98
76
56
03
E5
80
79
EE
DB
01
51
98
76
4E
24
77
79
EE
09
00
7B
76
4E
8F
82
B1
EE
8C
08
02
90
4E
8F
04
81
09
00
08
80
82
62
8F
03
98
85
E9
08
80
79
83
01
00
TERMINAL RESPONSE: SELECT ITEM 11.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
81
90
03
01
01
02
24
00
82
ETSI
02
82
81
Release 10
474
27.22.4.9.11.5
ETSI TS 102 384 V10.3.0 (2015-08)
Test requirement
The Terminal shall operate in the manner defined in expected sequence 11.1.
27.22.4.9.12
27.22.4.9.12.1
SELECT ITEM (UCS2 display in Katakana)
Definition and applicability
See clause 3.2.2.
27.22.4.9.12.2
Conformance requirement
The Terminal shall support the Proactive UICC: Select Item facility as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5, 6.4.9, 6.6.8, 6.8, 8.6, 8.7, 8.2, 8.9, 9.4 and 10.
27.22.4.9.12.3
Test purpose
To verify that the Terminal correctly presents the set of items in UCS2 coding contained in the SELECT ITEM
proactive UICC command, and returns a TERMINAL RESPONSE command to the UICC with the identifier of the
item chosen.
To verify that the Terminal allows a SELECT ITEM proactive UICC command within the maximum 255 byte
BER-TLV boundary.
To verify that the Terminal returns a TERMINAL RESPONSE with "Proactive UICC application session terminated by
the user", if the user has indicated the need to end the proactive UICC session.
To verify that the Terminal returns a TERMINAL RESPONSE with "Backwards move in the proactive UICC
application session requested by the user", if the user has indicated the need to go backwards in the proactive UICC
application session.
27.22.4.9.12.4
Method of test
27.22.4.9.12.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.9.12.4.2
Procedure
Expected Sequence 12.1 (SELECT ITEM with UCS2 in Katakana characters, 0x80 UCS2 coding, successful)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 12.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 12.1.1
Terminal → USER Display items of "80 1", "80 2"
ル
and "80
"80
5
6
ル
ル3" under the header of
ル0".
ル
Comments
Items use characters in Katakana.
USER → Terminal Select "80 2".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 12.1.1
ETSI
Release 10
475
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SELECT ITEM 12.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"80 0"
ル
Item
Identifier of item:
Text string of item:
1
"80 1"
Identifier of item:
Text string of item:
2
"80 2"
Identifier of item:
Text string of item:
3
"80 3"
ル
Item
ル
Item
ル
Coding:
BER-TLV:
D0
09
01
02
03
38
80
80
80
80
81
00
00
00
00
03
38
38
38
38
01
00
00
00
00
24
30
30
30
30
00
30
30
30
30
82
EB
EB
EB
EB
02
00
00
00
00
81
30
31
32
33
82
8F
8F
8F
85
0A
0A
0A
83
01
00
TERMINAL RESPONSE: SELECT ITEM 12.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
81
90
03
01
01
02
24
00
82
ETSI
02
82
81
Release 10
476
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 12.2 (SELECT ITEM with UCS2 in Katakana characters, 0x81 UCS2 coding, successful)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 12.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 12.2.1
Terminal → USER Display items of "81 1", "81 2"
ル
and "81
"81
5
6
ル
ル3" under the header of
ル0".
Comments
Items use characters in Katakana.
ル
USER → Terminal Select "81 2".
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 12.2.1
PROACTIVE COMMAND: SELECT ITEM 12.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"81 0"
ル
Item
Identifier of item:
Text string of item:
1
"81 1"
Identifier of item:
Text string of item:
2
"81 2"
Identifier of item:
Text string of item:
3
"81 3"
ル
Item
ル
Item
ル
Coding:
BER-TLV:
D0
07
04
38
EB
30
81
61
31
33
81
04
38
EB
03
61
31
32
01
38
EB
8F
24
31
31
08
TERMINAL RESPONSE: SELECT ITEM 12.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
00
EB
8F
03
82
30
08
81
02
8F
02
04
81
08
81
61
82
01
04
38
85
81
61
31
Release 10
477
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
81
90
03
01
01
02
24
00
82
02
82
81
83
01
00
Expected Sequence 12.3 (SELECT ITEM with UCS2 in Katakana characters, 0x82 UCS2 coding, successful)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SELECT ITEM 12.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
SELECT ITEM 12.3.1
Terminal → USER Display items of "82 1", "82 2"
ル
ル
ル3" under the header of
ル0".
Select "82ル2".
Comments
Items use characters in Katakana.
and "82
"82
5
6
USER → Terminal
Terminal → UICC TERMINAL RESPONSE: SELECT Command performed successfully.
ITEM 12.2.1
PROACTIVE COMMAND: SELECT ITEM 12.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
UICC
Terminal
"82 0"
ル
Item
Identifier of item:
Text string of item:
1
"82 1"
Identifier of item:
Text string of item:
2
"82 2"
Identifier of item:
Text string of item:
3
"82 3"
ル
Item
ル
Item
ル
Coding:
BER-TLV:
D0
08
82
04
30
34
82
04
30
A0
81
04
30
A0
38
03
30
A0
38
32
01
A0
38
32
CB
24
38
32
CB
33
ETSI
00
32
CB
32
82
CB
31
8F
02
30
8F
09
81
8F
09
03
82
09
02
82
85
01
82
04
Release 10
478
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SELECT ITEM 12.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SELECT ITEM
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Item identifier
Identifier of item chosen:
02
Coding:
BER-TLV:
81
90
27.22.4.9.12.5
03
01
01
02
24
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 12.1 to 12.3.
27.22.4.10
SEND SHORT MESSAGE
The test method is not defined in the present document as it depends on a present NAA.
27.22.4.11
Void
27.22.4.12
Void
27.22.4.13
SET UP CALL
The test method is not defined in the present document as it depends on a present NAA.
27.22.4.14
POLLING OFF
The test method is not defined in the present document as it depends on a present NAA.
27.22.4.15
27.22.4.15.1
PROVIDE LOCAL INFORMATION
Definition and applicability
See clause 3.2.2.
27.22.4.15.2
Conformance requirement
The Terminal shall support the PROVIDE LOCAL INFORMATION facility as defined in:
•
ETSI TS 102 223 [1], clause 6.4.15.
27.22.4.15.3
Test purpose
To verify that the Terminal returns the following requested local information within a TERMINAL RESPONSE:
•
Location Information according to current NAA;
•
the IMEI of the Terminal;
•
the Network Measurement results according to current NAA;
ETSI
Release 10
479
•
the current date, time and time zone;
•
the current language setting;
•
the Access Technology;
•
the ESN of the terminal;
•
the IMEISV of the terminal;
•
the Search Mode;
•
the Charge State of the Battery;
•
the Broadcast Network information.
ETSI TS 102 384 V10.3.0 (2015-08)
If the local information is stored in the Terminal; otherwise, sends the correct error code to the UICC in the
TERMINAL RESPONSE.
27.22.4.15.4
Method of tests
27.22.4.15.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as the Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.15.4.2
Procedure
Expected Sequence 1.1 (PROVIDE LOCAL INFORMATION, Location Information according to current NAA)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.2 (PROVIDE LOCAL INFORMATION, IMEI of the Terminal)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND PENDING:
PROVIDE LOCAL INFORMATION
1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PROVIDE
LOCAL INFORMATION 1.2.1
Terminal → UICC TERMINAL RESPONSE: PROVIDE Command performed successfully, IMEI
LOCAL INFORMATION 1.2.1
but spare digit shall be zero when
transmitted by the Terminal
PROACTIVE COMMAND: PROVIDE LOCAL INFORMATION 1.2.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"01" IMEI of the Terminal
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
ETSI
26
01
82
02
81
82
Release 10
480
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.2.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"01" IMEI of the Terminal
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
IMEI of the Terminal:
The IMEI of the Terminal
IMEI
The result coding depends on the Terminal IMEI value as declared in table A.1/23
Coding:
BER-TLV:
81
94
03
08
01
XX
26
XX
01
XX
82
XX
02
XX
82
XX
81
XX
83
XX
01
00
As an example, if the IMEI of the Terminal is "123456789012345" then
XX XX XX XX XX XX XX XX = 1A 32 54 76 98 10 32 04. For further details see also ETSI TS 124 008 [5],
clause 10.5.1.
Expected Sequence 1.3 (PROVIDE LOCAL INFORMATION, Network Measurement results according to
current NAA)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.4 (PROVIDE LOCAL INFORMATION, Date, Time, Time Zone)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND PENDING:
PROVIDE LOCAL INFORMATION 1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PROVIDE
LOCAL INFORMATION 1.4.1
Command performed successfully.
Terminal → UICC TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.4.1
PROACTIVE COMMAND: PROVIDE LOCAL INFORMATION 1.4.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"03" Date Time and Time Zone
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
ETSI
26
03
82
02
81
82
Release 10
481
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.4.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"03" Date Time and Time Zone
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Date-Time and Time Zone
Command performed successfully
th
date and time set by the user: 7 May 2002, 14h 08mn 17s, no time
zone information, as an example in TLV
Coding:
BER-TLV:
81
A6
03
07
01
20
26
50
03
70
82
41
02
80
82
71
81
FF
83
01
00
Expected Sequence 1.5 (PROVIDE LOCAL INFORMATION, Language setting)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
PROVIDE LOCAL INFORMATION
1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PROVIDE
LOCAL INFORMATION 1.5.1
Terminal → UICC TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.5.1
Comments
Command performed successfully.
PROACTIVE COMMAND: PROVIDE LOCAL INFORMATION 1.5.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"04" Language setting
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
26
04
82
02
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.5.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"04" Language setting
Device identities
Source device:
Terminal
ETSI
81
82
Release 10
482
ETSI TS 102 384 V10.3.0 (2015-08)
Destination device:
UICC
General Result:
Language
Command performed successfully
English ("en") as an example for TLV
Result
Coding:
BER-TLV:
81
AD
03
02
01
65
26
6E
04
82
02
82
81
83
01
00
Expected Sequence 1.6 Void
Expected Sequence 1.7 (PROVIDE LOCAL INFORMATION, Access Technology)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.8 (PROVIDE LOCAL INFORMATION, ESN of the terminal)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND PENDING:
PROVIDE LOCAL INFORMATION
1.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PROVIDE
LOCAL INFORMATION 1.8.1
Terminal → UICC TERMINAL RESPONSE: PROVIDE Command performed successfully,
LOCAL INFORMATION 1.8.1
IMEISV.
PROACTIVE COMMAND: PROVIDE LOCAL INFORMATION 1.8.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"07" ESN of the Terminal
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
26
07
82
02
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.8.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"07" ESN of the Terminal
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ESN of the Terminal:
The ESN of the Terminal
ESN
ETSI
81
82
Release 10
483
ETSI TS 102 384 V10.3.0 (2015-08)
The ESN is coded as in TIA/EIA-41-D [8].
The result coding depends on the Terminal ESN value as declared in table A.1/25.
Coding:
BER-TLV:
81
C6
03
04
01
XX
26
XX
07
XX
82
XX
02
82
81
83
01
00
Expected Sequence 1.9 (PROVIDE LOCAL INFORMATION, IMEISV of the terminal)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
PROVIDE LOCAL INFORMATION 1.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PROVIDE
LOCAL INFORMATION 1.9.1
Terminal → UICC TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.9.1
Comments
Command performed successfully, IMEISV.
PROACTIVE COMMAND: PROVIDE LOCAL INFORMATION 1.9.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"08" IMEISV of the Terminal
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
26
08
82
02
81
82
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.9.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"08" IMEISV of the Terminal
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
IMEISV
IMEISV of the Terminal:
The IMEISV of the Terminal
The result coding depends on the Terminal IMEISV value as declared in table A.2/24.
Coding:
BER-TLV:
81
E2
03
09
01
XX
26
XX
08
XX
82
XX
ETSI
02
XX
82
XX
81
XX
83
XX
01
XX
00
Release 10
484
ETSI TS 102 384 V10.3.0 (2015-08)
As an example, if the IMEISV of the Terminal is "1234567890123456" then
XX XX XX XX XX XX XX XX XX = 13 32 54 76 98 10 32 54 F6. For further details see also ETSI TS 124 008 [5].
Expected Sequence 1.10 (PROVIDE LOCAL INFORMATION, Search Mode)
The test method is not defined in the present document as it depends on a present NAA.
Expected Sequence 1.11 (PROVIDE LOCAL INFORMATION, charge state of the battery)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
PROVIDE LOCAL INFORMATION
1.11.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PROVIDE
LOCAL INFORMATION 1.11.1
Terminal → UICC TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.11.1
Comments
Command performed successfully.
PROACTIVE COMMAND: PROVIDE LOCAL INFORMATION 1.11.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"0A" Charge State of the Battery
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
26
0A
82
02
81
82
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.11.1
Logically:
Command details
Command number:
Command type:
Qualifier:
1
PROVIDE LOCAL INFORMATION
"0A" Charge State of the Battery
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Battery State:
Command performed successfully
XX where 0 ≤ XX ≤ 4
Coding:
BER-TLV:
81
E3
03
01
01
XX
26
0A
82
Expected Sequence 1.12 Void
ETSI
02
82
81
83
01
00
Release 10
485
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.13 (PROVIDE LOCAL INFORMATION, Broadcast Network information)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
PROVIDE LOCAL INFORMATION
1.13.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PROVIDE
LOCAL INFORMATION 1.13.1
Terminal → UICC TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.13.1
OR
TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.13.2
OR
TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.13.3
OR
TERMINAL RESPONSE: PROVIDE
LOCAL INFORMATION 1.13.4
Comments
Command performed successfully.
Detailed result depending on the Broadcast
network Technology available, either:
- DVB-H
- or DVB-T
- or DVB-SH
- or T-DMB
PROACTIVE COMMAND: PROVIDE LOCAL INFORMATION 1.13.1
Logically:
Command details
Command number:
Command type:
Qualifier:
Network Technology used
1
PROVIDE LOCAL INFORMATION
"0D" Broadcast Network information according to current Broadcast
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
26
0D
82
02
81
82
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.13.1 (DVB-H)
Logically:
Command details
Command number:
Command type:
Qualifier:
Network Technology used
Device identities
Source device:
Destination device:
1
PROVIDE LOCAL INFORMATION
"0D" Broadcast Network information according to current Broadcast
Terminal
UICC
Result
General Result: Command performed successfully
Broadcast Network Information
Broadcast Network Technology:
DVB-H
Broadcast Network Location Information:
Network_id: "XX XX"
Cell_id: "YY YY"
Hierarchy: Low priority "0Z" , where "0Z" is "01" or "02"
Number_of_subcell_id: "nn" where nn ≥ 1
Subcell_id(s): "SS … TT", length and content not verified
ETSI
Release 10
486
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
FA
03
Len
01
00
26
XX
0D
XX
82
YY
02
YY
82
0Z
81
nn
83
SS
01
…
00
TT
Len: length value is 7+nn
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.13.2 (DVB-T)
Logically:
Command details
Command number:
Command type:
Qualifier:
Network Technology used
1
PROVIDE LOCAL INFORMATION
"0D" Broadcast Network information according to current Broadcast
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Broadcast Network Information
Broadcast Network Technology:
DVB-T
Broadcast Network Location Information:
Network_id: "XX XX"
Cell_id: "YY YY"
Hierarchy: "FF"
Number_of_subcell_id: "nn" where nn ≥ 1
Subcell_id(s): "SS … TT", length and content not verified
Coding:
BER-TLV:
81
FA
03
Len
01
01
26
XX
0D
XX
82
YY
02
YY
82
FF
81
nn
83
SS
01
…
00
TT
Len: length value is 7+nn
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.13.3 (DVB-SH)
Logically:
Command details
Command number:
Command type:
Qualifier:
Network Technology used
Device identities
Source device:
Destination device:
1
PROVIDE LOCAL INFORMATION
"0D" Broadcast Network information according to current Broadcast
Terminal
UICC
Result
General Result:
Command performed successfully
Broadcast Network Information
Broadcast Network Technology:
DVB-SH
Broadcast Network Location Information:
Network_id: "XX XX"
Cell_id: "YY YY"
Hierarchy: Low priority "0Z" , where "0Z" is "01" or "02"
ETSI
Release 10
487
ETSI TS 102 384 V10.3.0 (2015-08)
Number_of_subcell_id: "nn" where nn ≥ 1
Subcell_id(s): "SS … TT", length and content not verified
Coding:
BER-TLV:
81
FA
03
Len
01
02
26
XX
0D
XX
82
YY
02
YY
82
0Z
81
nn
83
SS
01
…
00
TT
Len: length value is 7+nn
TERMINAL RESPONSE: PROVIDE LOCAL INFORMATION 1.13.4 (T-DMB)
Logically:
Command details
Command number:
Command type:
Qualifier:
Network Technology used
1
PROVIDE LOCAL INFORMATION
"0D" Broadcast Network information according to current Broadcast
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Broadcast Network Information
Broadcast Network Technology:
T-DMB
Broadcast Network Location Information:
none (FFS)
Coding:
BER-TLV:
27.22.4.15.5
81
FA
03
01
01
03
26
0D
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.13.
27.22.4.16
SET UP EVENT LIST
27.22.4.16.1
SET UP EVENT LIST (normal)
27.22.4.16.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.16.1.2
Conformance requirement
The Terminal shall support the Proactive UICC: Set Up Event List facility as defined in:
•
ETSI TS 102 223 [1], clauses 6.4.16 and 6.6.16.
Additionally the Terminal shall support the Event Download: Call Connect and the Event Download: Call Disconnected
mechanism as defined in:
•
ETSI TS 102 223 [1], clauses 11.2, 11.2.1, 11.2.2, 11.3, 11.3.1 and 11.3.2.
27.22.4.16.1.3
Test purpose
To verify that the Terminal accepts a list of events that it shall monitor the current list of events supplied by the UICC,
is able to have this current list of events replaced and is able to have the list of events removed.
ETSI
Release 10
488
ETSI TS 102 384 V10.3.0 (2015-08)
To verify that when the Terminal has successfully accepted or removed the list of events, it shall send TERMINAL
RESPONSE (OK) to the UICC and when the Terminal is not able to successfully accept or remove the list of events, it
shall send TERMINAL RESPONSE (Command beyond Terminal's capabilities).
27.22.4.16.1.4
Method of test
27.22.4.16.1.4.1
Initial conditions
The Terminal is connected to both the UICC Simulator.
The elementary files are coded as Card Application Toolkit default with the following exceptions.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.16.1.4.2
Procedure
Expected Sequence 1.1 (SET UP EVENT LIST, User Activity)
Step
1
2
3
4
5
6
7
8
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND PENDING: SET UP
EVENT LIST 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP EVENT
LIST 1.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP EVENT
LIST 1.1.1
UICC → Terminal PROACTIVE UICC SESSION ENDED
USER → Terminal User shall press any key
User Activity.
Terminal → UICC ENVELOPE: EVENT DOWNLOAD USER
ACTIVITY 1.1.1
UICC → Terminal PROACTIVE UICC SESSION ENDED
PROACTIVE COMMAND: SET UP EVENT LIST 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
UICC
Terminal
Event list
Event 1:
User Activity
Coding:
BER-TLV:
D0
01
0C
04
81
03
01
05
00
TERMINAL RESPONSE: SET UP EVENT LIST 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
ETSI
82
02
81
82
99
Release 10
489
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
05
00
82
02
82
81
02
82
81
83
01
00
ENVELOPE: EVENT DOWNLOAD USER ACTIVITY 1.1.1
Logically:
Event list
Event 1:
User Activity
Device identities
Source device:
Destination device:
Terminal
UICC
Coding:
BER-TLV:
D6
0A
99
01
04
82
Expected Sequence 1.2 (SET UP EVENT LIST, Replace Event)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP EVENT LIST
1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
EVENT LIST 1.2.1
Terminal → UICC TERMINAL RESPONSE: SET UP
EVENT LIST 1.2.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP EVENT LIST
1.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
EVENT LIST 1.2.2
Terminal → UICC TERMINAL RESPONSE: SET UP
EVENT LIST 1.2.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal User shall press any key
USER → Terminal User shall change the terminal's
language setting
Terminal → UICC ENVELOPE: EVENT DOWNLOAD
CALL DISCONNECT 1.2.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
Idle Screen Available and Language
Selection.
Language Selection.
Language Selection.
PROACTIVE COMMAND: SET UP EVENT LIST 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
ETSI
Release 10
490
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Terminal
Event list
Event 1:
Event 2:
Idle Screen Available
Language Selection
Coding:
BER-TLV:
D0
02
0D
05
81
07
03
01
05
00
82
02
81
82
99
TERMINAL RESPONSE: SET UP EVENT LIST 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
05
00
82
02
82
81
83
01
00
82
02
81
82
99
PROACTIVE COMMAND: SET UP EVENT LIST 1.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
UICC
Terminal
Event list
Event 1:
Language Selection
Coding:
BER-TLV:
D0
01
0C
07
81
03
01
05
00
TERMINAL RESPONSE: SET UP EVENT LIST 1.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
ETSI
Release 10
491
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
05
00
82
02
82
81
83
01
00
ENVELOPE: EVENT DOWNLOAD LANGUAGE SELECTION 1.2.2
Logically:
Event list
Event 1:
Language Selection
Device identities
Source device:
Destination device:
Terminal
UICC
Language
Language
'se'(Spanish) → 73 65
or 'de'64 65 (German) for instance: choose a language different
from the one initially set on the Terminal to check the proper
execution of the command
Coding:
BER-TLV:
D6
AD
0E
02
99
73
01
65
02
82
02
83
81
9C
01
Expected Sequence 1.3 (SET UP EVENT LIST, Remove Event)
Step
1
2
3
4
5
6
7
8
9
10
11
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP EVENT LIST
1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP Language Selection.
EVENT LIST 1.3.1
Terminal → UICC TERMINAL RESPONSE: SET UP
EVENT LIST 1.3.1
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP EVENT LIST
1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP Remove Event.
EVENT LIST 1.3.2
Terminal → UICC TERMINAL RESPONSE: SET UP
EVENT LIST 1.3.2
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal User shall change the terminal's
language setting
Terminal → UICC No ENVELOPE: EVENT
DOWNLOAD (language selection)
sent
ETSI
00
Release 10
492
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SET UP EVENT LIST 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
UICC
Terminal
Event list
Event 1:
Language Selection
Coding:
BER-TLV:
D0
01
0C
07
81
03
01
05
00
82
02
81
82
99
TERMINAL RESPONSE: SET UP EVENT LIST 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
05
00
82
02
82
81
83
01
00
82
02
81
82
99
PROACTIVE COMMAND: SET UP EVENT LIST 1.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
Event list:
UICC
Terminal
Empty
Coding:
BER-TLV:
D0
00
0B
81
03
01
05
ETSI
00
Release 10
493
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP EVENT LIST 1.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
05
00
82
02
82
81
83
01
00
Expected Sequence 1.4 (SET UP EVENT LIST, Remove Event on Terminal Power Cycle)
Step
1
2
3
4
5
6
7
8
9
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP EVENT LIST
1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP Language Selection.
EVENT LIST 1.4.1
Terminal → UICC TERMINAL RESPONSE: SET UP
EVENT LIST 1.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
User → Terminal Power off Terminal
User → Terminal Power on Terminal
USER → Terminal User shall change the terminal's
language setting
Terminal → UICC No ENVELOPE: EVENT
DOWNLOAD (language selection)
sent
PROACTIVE COMMAND: SET UP EVENT LIST 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
UICC
Terminal
Event list
Event 1:
Language Selection
Coding:
BER-TLV:
D0
01
0C
07
81
03
01
05
ETSI
00
82
02
81
82
99
Release 10
494
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP EVENT LIST 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP EVENT LIST
'00'
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.16.1.5
81
03
01
05
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.4.
27.22.4.17
PERFORM CARD APDU
27.22.4.17.1
27.22.4.17.1.1
PERFORM CARD APDU (normal)
Definition and applicability
See clause 3.2.2.
27.22.4.17.1.2
Conformance requirement
The Terminal shall support the Proactive UICC: Perform Card APDU facility as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 5.2, 6.4.17, 6.6.17, 6.8, 8.6, 8.7, 8.35, 8.36 and 8.12.9.
Additionally the Terminal shall support multiple card operation as defined in:
•
ETSI TS 102 223 [1], clauses 6.4.19, 6.6.19, 6.4.18 and 6.6.18.
27.22.4.17.1.3
Test purpose
To verify that the Terminal sends an APDU command to the additional card identified in the PERFORM CARD APDU
proactive UICC command, and successfully returns the result of the execution of the command in the TERMINAL
RESPONSE command send to the UICC.
The Terminal-Manufacturer can assign the card reader identifier from 0 to 7.
This test applies for Terminals with only one additional card reader.
In this particular case the card reader identifier 1 is chosen.
In this particular case a special Test-SIM (TestSIM) with T=0 protocol is chosen as additional card for the additional
Terminal card reader (for coding of the TestSIM see annex A).
27.22.4.17.1.4
Method of test
27.22.4.17.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The TestSIM is inserted in the additional Terminal card reader.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
ETSI
Release 10
495
ETSI TS 102 384 V10.3.0 (2015-08)
If the Terminal supports a detachable card reader, the card reader shall be attached to the Terminal.
The elementary files of the TestSIM are coded as defined in annex A. Another card with different parameters may be
used as TestSIM to execute these tests. In this case the UICC Simulator shall take into account the corresponding
response data.
27.22.4.17.1.4.2
Procedure
Expected Sequence 1.1 (PERFORM CARD APDU, card reader 1, additional card inserted, Select MF and Get
Response)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: POWER ON CARD
1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
POWER ON CARD 1.1.1
Terminal → SIM2 RESET CARD
SIM2 → Terminal ANSWER TO RESET 1.1
Terminal → UICC TERMINAL RESPONSE: POWER
ON CARD 1.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.1.1
Terminal → SIM2 C-APDU: SELECT 1.1
SIM2 → Terminal R-APDU: SELECT 1.1
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.1.2
Terminal → SIM2 C-APDU: GET RESPONSE 1.1
SIM2 → Terminal R-APDU: GET RESPONSE 1.1
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.1.2
Comments
Power on card reader 1.
Perform electrical initialization.
ATR
ATR
Select Masterfile.
Select Masterfile.
Command performed successfully - length
'1B' of response data.
Get Response with length '1B'.
Get Response with length '1B'.
Response data with length '1B'.
Response data with length '1B'.
PROACTIVE COMMAND POWER ON CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
ETSI
31
00
82
02
81
11
Release 10
496
ETSI TS 102 384 V10.3.0 (2015-08)
ANSWER TO RESET 1.1
Logically:
TS (Initial character):
T0 (Format character):
'3B'
'86' (Following interface characters: TD(1), number of historical
characters: 6)
'00' (Following interface characters: none, Transfer protocol: T=0)
91
99
00
12
C1
00
TD1:
T1:
T2:
T3:
T4:
T5:
T6:
Coding:
Coding:
3B
86
00
91
99
00
12
C1
00
TERMINAL RESPONSE: POWER ON CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card ATR
TS (Initial character):
T0 (Format character):
'3B'
'86' (Following interface characters: TD(1), number of historical
characters: 6)
'00' (Following interface characters: none, Transfer protocol: T=0)
91
99
00
12
C1
00
TD1:
T1:
T2:
T3:
T4:
T5:
T6:
Coding:
BER-TLV:
81
A1
03
09
01
3B
31
86
00
00
82
91
02
99
82
00
PROACTIVE COMMAND PERFORM CARD APDU 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
ETSI
81
12
83
C1
01
00
00
Release 10
497
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
Master File
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
07
12
A0
81
A4
03
00
01
00
30
02
00
3F
82
00
02
81
11
A2
C-APDU: SELECT 1.1
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
Master File
Coding:
Coding:
A0
A4
00
00
02
3F
00
R-APDU: SELECT 1.1
Logically:
Status Words
SW1/SW2:
Command performed successfully - length '1B' of response data
Coding:
Coding:
9F
1B
TERMINAL RESPONSE: PERFORM CARD APDU 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
R-APDU
Status Words
SW1/SW2:
Command performed successfully
Command performed successfully - length '1B' of response data
ETSI
Release 10
498
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
A3
03
02
01
9F
30
1B
00
82
02
82
81
83
01
00
02
81
11
A2
PROACTIVE COMMAND PERFORM CARD APDU 1.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
'00'
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Le:
'A0'
GET RESPONSE
'00'
'00'
'1B'
Coding:
BER-TLV:
D0
05
10
A0
81
C0
03
00
01
00
30
1B
00
82
C-APDU: GET RESPONSE 1.1
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Le:
'A0'
GET RESPONSE
'00'
'00'
'1B'
Coding:
Coding:
A0
C0
00
00
R-APDU: GET RESPONSE 1.1
Logically:
R-APDU data
RFU:
Not allocated memory:
File ID:
Type of file:
RFU:
Length of following data:
File characteristics:
Clock Stop:
Min. frequency for 3GPP algorithm:
Technology identification:
CHV1:
DFs in current directory:
'00 00'
'653 bytes'
Master File
MF
00 00 22 FF 01'
14 bytes'
Not allowed
13/8 MHz
3V Technology SIM
disabled
2
ETSI
1B
Release 10
499
EFs in current directory:
Number of CHV and admin. Codes:
RFU byte 18:
CHV1 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
Unlock CHV1 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
CHV2 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
Unlock CHV2 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
RFU bytes 23:
Reserved for admin. management:
Status Words
SW1/SW2:
ETSI TS 102 384 V10.3.0 (2015-08)
8
3
00
3
000
Initialized
10
000
Initialized
3
000
Initialized
10
000
Initialized
00
00 83 00 FF
Normal ending of command
Coding:
Coding:
00
0E
83
00
9B
00
02
02
FF
8D
08
90
3F
03
00
00
00
01
83
00
8A
00
83
TERMINAL RESPONSE: PERFORM CARD APDU 1.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
R-APDU data
RFU:
Not allocated memory:
File ID:
Type of file:
RFU:
Length of following data:
File characteristics:
Clock Stop:
Min. frequency for 3GPP algorithm:
Technology identification:
CHV1:
DFs in current directory:
EFs in current directory:
Number of CHV and admin. Codes:
RFU byte 18:
Command performed successfully
'00 00'
'653 bytes'
Master File
MF
00 00 22 FF 01'
14 bytes'
Not allowed
13/8 MHz
3V Technology SIM
disabled
2
3
00
ETSI
22
8A
FF
00
01
00
Release 10
500
CHV1 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
Unlock CHV1 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
CHV2 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
Unlock CHV2 status:
False representations remaining:
RFU-bits 7-5:
Secret code:
RFU bytes 23:
Reserved for admin. management:
Status Words
SW1/SW2:
ETSI TS 102 384 V10.3.0 (2015-08)
3
000
Initialized
10
000
Initialized
3
000
Initialized
10
000
Initialized
00
00 83 00 FF
Normal ending of command
Coding:
BER-TLV:
81
A3
FF
03
0F
01
01
00
0E
30
00
90
00
02
00
82
8D
02
3F
82
00
81
01
83
00
01
00
00
22
Expected Sequence 1.2 (PERFORM CARD APDU, card reader 1, additional card inserted, Select DF GSM,
Select EF PLMN , Update Binary, Read Binary on EF PLMN)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: POWER ON CARD
1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
POWER ON CARD 1.1.1
Terminal → SIM2 RESET CARD
SIM2 → Terminal ANSWER TO RESET 1.1
Terminal → UICC TERMINAL RESPONSE: POWER
ON CARD 1.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.2.1
Terminal → SIM2 C-APDU: SELECT 1.2a
SIM2 → Terminal R-APDU: SELECT 1.2a
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.2.1
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.2.2
Terminal → SIM2 C-APDU: SELECT 1.2b
SIM2 → Terminal R-APDU: SELECT 1.2b
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.2.2
ETSI
Comments
Power on card reader 1.
Perform electrical initialization.
ATR.
ATR.
Select GSM.
Select GSM.
Select PLMN.
Select PLMN.
Release 10
Step
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
501
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.2.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.2.3
Terminal → SIM2 C-APDU: UPDATE BINARY 1.2
SIM2 → Terminal R-APDU: UPDATE BINARY 1.2
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.2.3
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.2.4
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.2.4
Terminal → SIM2 C-APDU: READ BINARY 1.2
SIM2 → Terminal R-APDU: READ BINARY 1.2
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.2.4
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.2.5
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.2.5
Terminal → SIM2 C-APDU: UPDATE BINARY 1.2a
SIM2 → Terminal R-APDU: UPDATE BINARY 1.2
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.2.3
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Update Binary.
Update Binary.
Read Binary.
Read Binary.
Update Binary.
Update Binary.
PROACTIVE COMMAND PERFORM CARD APDU 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
DF GSM
Coding:
BER-TLV:
D0
07
12
A0
81
A4
03
00
01
00
30
02
ETSI
00
7F
82
20
02
81
11
A2
Release 10
502
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PERFORM CARD APDU 1.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
EF PLMN
Coding:
BER-TLV:
D0
07
12
A0
81
A4
03
00
01
00
30
02
00
6F
82
30
02
81
11
A2
PROACTIVE COMMAND: PERFORM CARD APDU 1.2.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
UPDATE BINARY
'00'
'00'
'18'
'00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0B 0E 0F 10 11 12 13 14
15 16 17'
Coding:
BER-TLV:
D0
1D
06
12
28
A0
07
13
81
D6
08
14
03
00
09
15
01
00
0A
16
30
18
0B
17
00
00
0C
82
01
0D
PROACTIVE COMMAND: PERFORM CARD APDU 1.2.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
ETSI
02
02
0E
81
03
0F
11
04
10
A2
05
11
Release 10
503
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Le:
'A0'
READ BINARY
'00'
'00'
'18'
Coding:
BER-TLV:
D0
05
10
A0
81
B0
03
00
01
00
30
18
00
82
02
81
11
A2
PROACTIVE COMMAND: PERFORM CARD APDU 1.2.5
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
UPDATE BINARY
'00'
'00'
'18'
'FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF'
Coding:
BER-TLV:
D0
1D
FF
FF
28
A0
FF
FF
81
D6
FF
FF
03
00
FF
FF
01
00
FF
FF
30
18
FF
FF
00
FF
FF
82
FF
FF
02
FF
FF
81
FF
FF
C-APDU: SELECT 1.2a
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
DF GSM
Coding:
Coding:
A0
A4
00
ETSI
00
02
7F
20
11
FF
FF
A2
FF
FF
Release 10
504
ETSI TS 102 384 V10.3.0 (2015-08)
C-APDU: SELECT 1.2b
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
EF PLMN
Coding:
Coding:
A0
A4
00
00
02
6F
30
C-APDU: UPDATE BINARY 1.2
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
UPDATE BINARY
'00'
'00'
'18'
'00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0B 0E 0F 10 11 12 13 14 15
16 17'
Coding:
Coding:
A0
07
13
D6
08
14
00
09
15
00
0A
16
18
0B
17
00
0C
01
0D
02
0E
03
0F
04
10
05
11
06
12
C-APDU: READ BINARY 1.2
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Le:
'A0'
READ BINARY
'00'
'00'
'18'
Coding:
Coding:
A0
B0
00
00
18
C-APDU: UPDATE BINARY 1.2a
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
UPDATE BINARY
'00'
'00'
'18'
'FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF'
ETSI
Release 10
505
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
Coding:
A0
FF
FF
D6
FF
FF
00
FF
FF
00
FF
FF
18
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
R-APDU: SELECT 1.2a
Logically:
Status Words
SW1/SW2:
Normal ending of command - length '1B' of response data
Coding:
Coding:
9F
1B
R-APDU: SELECT 1.2b
Logically:
Status Words
SW1/SW2:
Normal ending of command - length '0F' of response data
Coding:
Coding:
9F
0F
R-APDU: UPDATE BINARY 1.2
Logically:
Status Words
SW1/SW2:
Normal ending of command
Coding:
Coding:
90
00
R-APDU: READ BINARY 1.2
Logically:
R-APDU data
Data:
'00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0B 0E 0F 10 11 12 13 14 15
16 17'
Status Words
SW1/SW2:
Normal ending of command
Coding:
Coding:
00
0C
90
01
0D
00
02
0E
03
0F
04
10
05
11
06
12
07
13
TERMINAL RESPONSE: PERFORM CARD APDU 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
ETSI
08
14
09
15
0A
16
0B
17
Release 10
506
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
R-APDU
Status Words
SW1/SW2:
Command performed successfully - length 1B of response data
Coding:
BER-TLV:
81
A3
03
02
01
9F
30
1B
00
82
02
82
81
83
01
00
TERMINAL RESPONSE: PERFORM CARD APDU 1.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
R-APDU
Status Words
SW1/SW2:
Command performed successfully - length 0F of response data
Coding:
BER-TLV:
81
A3
03
02
01
9F
30
0F
00
82
02
82
81
TERMINAL RESPONSE: PERFORM CARD APDU 1.2.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
R-APDU
Status Words
SW1/SW2:
Command performed successfully
Normal ending of command
ETSI
83
01
00
Release 10
507
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
A3
03
02
01
90
30
00
00
82
02
82
81
83
01
00
TERMINAL RESPONSE: PERFORM CARD APDU 1.2.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
R-APDU
R-APDU data
Data:
'00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0B 0E 0F 10 11 12 13 14
15 16 17'
Status Words
SW1/SW2:
Normal ending of command
Coding:
BER-TLV:
81
A3
0A
16
03
1A
0B
17
01
00
0C
90
30
01
0D
00
00
02
0E
82
03
0F
02
04
10
82
05
11
81
06
12
83
07
13
01
08
14
00
09
15
Expected Sequence 1.3 (PERFORM CARD APDU, card reader 1, card inserted, card powered off)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: POWER OFF CARD
1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
POWER OFF CARD 1.3.1
Terminal → SIM2 POWER OFF CARD
Terminal → UICC TERMINAL RESPONSE: POWER
OFF CARD 1.3.1
Terminal
SIM2 is powered off from Terminal
card reader
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.1.1
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.3.1
ETSI
Comments
Power off card reader 1.
Power off card reader 1.
Successful.
Select Master File.
Card powered off.
Release 10
508
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: POWER OFF CARD 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
32
00
82
02
81
11
81
83
01
81
83
02
TERMINAL RESPONSE: POWER OFF CARD 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
00
03
01
32
00
82
02
82
TERMINAL RESPONSE: PERFORM CARD APDU 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card powered off
Coding:
BER-TLV:
81
38
03
04
01
30
00
ETSI
82
02
82
Release 10
509
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.4 (PERFORM CARD APDU, card reader 1, no card inserted)
Step
1
Direction
Terminal
2
UICC → Terminal
3
4
Terminal → UICC
UICC → Terminal
5
Terminal → UICC
Message/Action
SIM2 is removed from Terminal
card reader
PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.1.1
FETCH
PROACTIVE COMMAND:
PERFORM CARD APDU 1.1.1
TERMINAL RESPONSE:
PERFORM CARD APDU 1.4.1
Comments
Select Master File.
No card inserted.
TERMINAL RESPONSE: PERFORM CARD APDU 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card removed or not present
Coding:
BER-TLV:
81
38
03
02
01
30
00
82
02
82
81
83
02
Expected Sequence 1.5 (PERFORM CARD APDU, card reader 7 (which is not the valid card reader identifier of
the additional Terminal card reader))
Step
1
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 1.5.1
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 1.5.1
Comments
Invalid card reader ID.
Select Master File.
Specified reader not valid.
PROACTIVE COMMAND: PERFORM CARD APDU 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
UICC
Card Reader 7
ETSI
Release 10
510
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
ETSI TS 102 384 V10.3.0 (2015-08)
'A0'
SELECT
'00'
'00'
'02'
Master File
Coding:
BER-TLV:
D0
07
12
A0
81
A4
03
00
01
00
30
02
00
3F
82
00
02
81
17
A2
C-APDU: SELECT 1.1
Logically:
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
Master File
Coding:
Coding:
A0
A4
00
00
02
3F
00
TERMINAL RESPONSE: PERFORM CARD APDU 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Specified reader not valid
Coding:
BER-TLV:
27.22.4.17.1.5
81
38
03
09
01
30
00
82
02
82
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.5.
27.22.4.17.2
PERFORM CARD APDU (detachable card reader)
27.22.4.17.2.1
Definition and applicability
See clause 3.2.2.
ETSI
81
83
02
Release 10
511
27.22.4.17.2.2
Conformance requirement
27.22.4.17.2.3
Test purpose
ETSI TS 102 384 V10.3.0 (2015-08)
To verify that the Terminal sends an APDU command to the additional card identified in the PERFORM CARD APDU
proactive UICC command, and successfully returns the result of the execution of the command in the TERMINAL
RESPONSE command send to the UICC.
27.22.4.17.2.4
Method of test
27.22.4.17.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The card reader shall be detached from the Terminal.
27.22.4.17.2.4.2
Procedure
Expected Sequence 2.1 (PERFORM CARD APDU, card reader 1, card reader detached)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: PERFORM CARD
APDU 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
PERFORM CARD APDU 2.1.1
Terminal → UICC TERMINAL RESPONSE:
PERFORM CARD APDU 2.1.1
Comments
Select Master File.
Card reader detached.
PROACTIVE COMMAND: PERFORM CARD APDU 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
UICC
Card Reader 1
C-APDU
Class:
Instruction:
P1 parameter:
P2 parameter:
Lc:
Data:
'A0'
SELECT
'00'
'00'
'02'
Master File
Coding:
BER-TLV:
D0
07
12
A0
81
A4
03
00
01
00
30
02
ETSI
00
3F
82
00
02
81
11
A2
Release 10
512
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: PERFORM CARD APDU 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PERFORM CARD APDU
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card reader removed or not present
Coding:
BER-TLV:
27.22.4.17.2.5
81
38
03
01
01
30
00
82
02
82
81
83
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.18
POWER OFF CARD
27.22.4.18.1
POWER OFF CARD (normal)
27.22.4.18.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.18.1.2
Conformance requirement
The Terminal shall support the Proactive UICC: Power Off Card facility as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.18, 6.6.18, 8.6, 8.7, 8.12, 8.12.9, 5.2 and annex H.
27.22.4.18.1.3
Test purpose
To verify that the Terminal closes a session with the additional card identified in the POWER OFF CARD proactive
UICC command, and successfully returns result in the TERMINAL RESPONSE command send to the UICC.
The Terminal-Manufacturer can assign the card reader identifier from 0 to 7.
This test applies for Terminals with only one additional card reader.
In this particular case the card reader identifier 1 is chosen.
27.22.4.18.1.4
Method of test
27.22.4.18.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The Terminal card reader is connected to a SIM Simulator (SIM2). Instead of a SIM Simulator a card with different
parameters may be used as SIM2 to execute these tests. In this case the UICC Simulator shall take into account the
corresponding response data.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
If the Terminal supports a detachable card reader, the card reader shall be attached to the Terminal.
Prior to this test the Terminal shall have powered on the SIM Simulator (SIM2).
ETSI
Release 10
513
27.22.4.18.1.4.2
ETSI TS 102 384 V10.3.0 (2015-08)
Procedure
Expected Sequence 1.1 (POWER OFF CARD, card reader 1)
Step
1
2
3
4
5
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
POWER OFF CARD 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: POWER OFF
CARD 1.1.1
Terminal → SIM2 POWER OFF CARD
Terminal → UICC TERMINAL RESPONSE: POWER OFF
CARD 1.1.1
Comments
Power off card reader 1.
Power off card reader 1.
Successful.
PROACTIVE COMMAND: POWER OFF CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
32
00
82
02
81
11
81
83
01
TERMINAL RESPONSE: POWER OFF CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
00
03
01
32
00
82
02
82
Expected Sequence 1.2 (POWER OFF CARD, card reader 1, no card inserted)
Step
1
2
3
4
5
Direction
Message/Action
SIM2
SIM2 is removed from Terminal card reader
UICC → Terminal PROACTIVE COMMAND PENDING: POWER
OFF CARD 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: POWER OFF CARD
1.1.1
Terminal → UICC TERMINAL RESPONSE: POWER OFF CARD
1.2.1
ETSI
Comments
Power off card reader 1.
No card inserted.
Release 10
514
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: POWER OFF CARD 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card removed or not present
Coding:
BER-TLV:
27.22.4.18.1.5
81
38
03
02
01
32
00
82
02
82
81
83
02
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.2.
27.22.4.18.2
27.22.4.18.2.1
POWER OFF CARD (detachable card reader)
Definition and applicability
See clause 3.2.2.
27.22.4.18.2.2
Conformance requirement
Void.
27.22.4.18.2.3
Test purpose
To verify that the Terminal closes a session with the additional card identified in the POWER OFF CARD proactive
UICC command, and successfully returns result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.18.2.4
Method of test
27.22.4.18.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The Terminal card reader is connected to a SIM Simulator (SIM2).
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
Prior to this test the Terminal shall have powered on the SIM Simulator (SIM2).
The card reader shall be detached from the Terminal.
27.22.4.18.2.4.2
Procedure
Expected Sequence 2.1 (POWER OFF CARD, card reader 1, no card reader attached)
Step
1
2
3
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
POWER OFF CARD 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: POWER
OFF CARD 2.1.1
ETSI
Comments
Power off card reader 1.
Release 10
Step
4
515
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → UICC TERMINAL RESPONSE: POWER OFF Card reader removed or not present.
CARD 2.1.1
PROACTIVE COMMAND: POWER OFF CARD 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
32
00
82
02
81
11
81
83
02
TERMINAL RESPONSE: POWER OFF CARD 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card reader removed or not present
Coding:
BER-TLV:
27.22.4.18.2.5
81
38
03
01
01
32
00
82
02
82
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.19
POWER ON CARD
27.22.4.19.1
POWER ON CARD (normal)
27.22.4.19.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.19.1.2
Conformance requirement
The Terminal shall support the Proactive UICC: Power On Card facility as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 6.4.19, 6.6.19, 8.6, 8.7, 8.12, 8.12.9, 8.34, 5.2 and annex H.
•
ISO/IEC 7816-3 [7].
ETSI
Release 10
516
27.22.4.19.1.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal starts a session with the additional card identified in the POWER ON CARD proactive
UICC command, and successfully returns the Answer To Reset within the TERMINAL RESPONSE command send to
the UICC.
The Terminal-Manufacturer can assign the card reader identifier from 0 to 7.
This test applies for Terminals with only one additional card reader.
In this particular case the card reader identifier 1 is chosen.
27.22.4.19.1.4
Method of test
27.22.4.19.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The Terminal card reader is connected to a SIM Simulator (SIM2). Instead of the SIM Simulator a card with different
parameters may be used as SIM2 to execute these tests. In this case the UICC Simulator shall take into account the
corresponding response data.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
If the Terminal supports a detachable card reader, the card reader shall be attached to the Terminal.
27.22.4.19.1.4.2
Procedure
Expected Sequence 1.1 (POWER ON CARD, card reader 1)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
POWER ON CARD 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: POWER ON
CARD 1.1.1
Terminal → SIM2 RESET CARD
SIM2 → Terminal ANSWER TO RESET 1.1.1
Terminal → UICC TERMINAL RESPONSE: POWER ON
CARD 1.1.1
Comments
Power on card reader 1.
Perform electrical initialization.
ATR
ATR
PROACTIVE COMMAND: POWER ON CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
ETSI
31
00
82
02
81
11
Release 10
517
ETSI TS 102 384 V10.3.0 (2015-08)
ANSWER TO RESET 1.1.1
Logically:
TS (Initial character):
T0 (Format character):
T1 (Historical character):
T2 (Historical character):
T3 (Historical character):
T4 (Historical character):
T5 (Historical character):
T6 (Historical character):
T7 (Historical character):
T8 (Historical character):
T9 (Historical character):
T10 (Historical character):
T11 (Historical character):
T12 (Historical character):
T13 (Historical character):
T14 (Historical character):
T15 (Historical character):
'3B'
0F
'P'
'o'
'w'
'e'
'r'
'O'
'n'
'C'
'a'
'r'
'd'
'T'
'e'
's'
't'
Coding:
BER-TLV:
3B
64
0F
54
50
65
6F
74
77
75
65
72
4F
6E
TERMINAL RESPONSE: POWER ON CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Card ATR
TS (Initial character):
T0 (Format character):
T1 (Historical character):
T2 (Historical character):
T3 (Historical character):
T4 (Historical character):
T5 (Historical character):
T6 (Historical character):
T7 (Historical character):
T8 (Historical character):
T9 (Historical character):
T10 (Historical character):
T11 (Historical character):
T12 (Historical character):
T13 (Historical character):
T14 (Historical character):
T15 (Historical character):
Command performed successfully
'3B'
0F
'P'
'o'
'w'
'e'
'r'
'O'
'n'
'C'
'a'
'r'
'd'
'T'
'e'
's'
't'
ETSI
43
61
72
Release 10
518
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
A1
61
03
11
72
01
3B
64
31
0F
54
00
50
65
82
6F
74
02
77
75
82
65
81
72
83
4F
01
6E
00
43
Expected Sequence 1.2 (POWER ON CARD, card reader 1, no ATR)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: POWER ON CARD
1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
POWER ON CARD 1.1.1
Terminal → SIM2 RESET CARD
SIM2 → Terminal NO ATR
Terminal → UICC TERMINAL RESPONSE: POWER
ON CARD 1.2.1
Comments
Power on card reader 1.
Perform electrical initialization.
No ATR
No ATR
TERMINAL RESPONSE: POWER ON CARD 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card mute
Coding:
BER-TLV:
81
06
03
01
31
00
82
02
82
81
83
02
Expected Sequence 1.3 (POWER ON CARD, card reader 1, no card inserted)
Step
1
Direction
SIM2
2
UICC → Terminal
3
4
Terminal → UICC
UICC → Terminal
5
Terminal → UICC
Message/Action
Comments
SIM2 is removed from Terminal
card reader
PROACTIVE COMMAND
PENDING: POWER ON CARD
1.1.1
FETCH
PROACTIVE COMMAND:
Power on card reader 1.
POWER ON CARD 1.1.1
TERMINAL RESPONSE: POWER Card removed or not present.
ON CARD 1.3.1
ETSI
38
Release 10
519
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: POWER ON CARD 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
Card reader 0
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card removed or not present
Coding:
BER-TLV:
27.22.4.19.1.5
81
02
03
01
31
00
82
02
82
81
83
02
38
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.3.
27.22.4.19.2
27.22.4.19.2.1
POWER ON CARD (detachable card reader)
Definition and applicability
See clause 3.2.2.
27.22.4.19.2.2
Conformance requirement
27.22.4.19.2.3
Test purpose
To verify that the Terminal starts a session with the additional card identified in the POWER ON CARD proactive
UICC command, and successfully returns the Answer To Reset within the TERMINAL RESPONSE command send to
the UICC.
27.22.4.19.2.4
Method of test
27.22.4.19.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default with the following exceptions.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The card reader shall be detached from the Terminal.
27.22.4.19.2.4.2
Procedure
Expected Sequence 2.1 (POWER ON CARD, card reader 1, no card reader attached)
Step
1
2
3
4
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: POWER ON CARD
2.1.1
Terminal → UICC FETCH
Power on card reader 1.
UICC → Terminal PROACTIVE COMMAND:
POWER ON CARD 2.1.1
Terminal → UICC TERMINAL RESPONSE: POWER Card reader removed or not present.
ON CARD 2.1.1
ETSI
Release 10
520
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: POWER ON CARD 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
31
00
82
02
81
11
TERMINAL RESPONSE: POWER ON CARD 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
Card reader 0
UICC
Result
General Result:
Additional Information:
MultipleCard commands error
Card reader removed or not present
Coding:
BER-TLV:
27.22.4.19.2.5
81
01
03
01
31
00
82
02
82
81
83
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.20
27.22.4.20.1
27.22.4.20.1.1
GET READER STATUS
GET READER STATUS (normal)
Definition and applicability
See clause 3.2.2.
27.22.4.20.1.2
Conformance requirement
The Terminal shall support the Proactive UICC: Get Card Reader Status facility as defined in:
•
ETSI TS 102 223 [1], clauses 6.1, 5.2, 6.4.20, 6.6.20, 6.8, 8.6, 8.7, 8.33, 8.57 and annex H.
Additionally the Terminal shall support multiple card operation as defined in:
•
ETSI TS 102 223 [1], clauses 6.4.19, 6.6.19, 6.4.18 and 6.6.18.
ETSI
38
Release 10
521
27.22.4.20.1.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the Terminal sends starts a session with the additional card identified in the GET CARD READER
STATUS proactive UICC command, and successfully returns information about all interfaces to additional card
reader(s) in the TERMINAL RESPONSE command send to the UICC.
The Terminal-Manufacturer can assign the card reader identifier from 0 to 7.
This test applies for Terminals with only one additional card reader.
In this particular case the card reader identifier 1 is chosen.
In this test case the SIM-Simulator (SIM2) shall response with the ATR "3B 00".
27.22.4.20.1.4
Method of test
27.22.4.20.1.4.1
Initial conditions
The Terminal shall support the Proactive UICC: Get Card Reader Status (Card Reader Status) facility. The Terminal is
connected to the UICC Simulator.
The Terminal card reader is connected to a SIM Simulator (SIM2). Instead of the SIM Simulator a card with different
parameters may be used as SIM2 to execute these tests. In this case the UICC Simulator shall take into account the
corresponding response data.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
If the Terminal supports a detachable card reader, the card reader shall be attached to the Terminal.
Prior to this test the Terminal shall have powered on the SIM Simulator (SIM2).
27.22.4.20.1.4.2
Procedure
Expected Sequence 1.1 (GET CARD READER STATUS, card reader 1, card inserted, card powered)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
POWER ON CARD 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: POWER ON
CARD 1.1.1
Terminal → SIM2 RESET CARD
SIM2 → Terminal ANSWER TO RESET 1.1.1
Terminal → UICC TERMINAL RESPONSE: POWER ON
CARD 1.1.1
UICC → Terminal PROACTIVE COMMAND PENDING: GET
CARD READER STATUS 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET CARD
READER STATUS 1.1.1
Terminal → UICC TERMINAL RESPONSE: GET CARD
READER STATUS 1.1.1a
Or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.1.1b
or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.1.1c
or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.1.1d
ETSI
Comments
Power on card reader 1.
Perform electrical initialization.
ATR
ATR
Get Card Reader Status.
Successful.
Successful.
Successful.
Successful.
Release 10
522
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: POWER ON CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
31
00
82
02
81
11
ANSWER TO RESET 1.1.1
Logically:
TS (Initial character):
T0 (Format character):
'3B'
'00'
Coding:
Coding:
3B
00
TERMINAL RESPONSE: POWER ON CARD 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER ON CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card ATR
TS (Initial character):
T0 (Format character):
'3B'
'00'
Coding:
BER-TLV:
81
A1
03
02
01
3B
31
00
00
82
02
82
PROACTIVE COMMAND: GET CARD READER STATUS 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
ETSI
81
83
01
00
Release 10
523
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
33
00
82
02
81
82
81
83
01
TERMINAL RESPONSE: GET CARD READER STATUS 1.1.1a
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'01'
'No'
Yes
'Yes'
Yes
Yes
Coding:
BER-TLV:
81
00
03
A0
01
01
33
F1
00
82
02
82
TERMINAL RESPONSE: GET CARD READER STATUS 1.1.1b
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
Command performed successfully
'01'
'No'
Yes
'No'
Yes
Yes
ETSI
Release 10
524
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
00
03
A0
01
01
33
D1
00
82
02
82
81
83
01
81
83
01
81
83
01
TERMINAL RESPONSE: GET CARD READER STATUS 1.1.1c
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'01'
'Yes'
Yes
'Yes'
Yes
Yes
Coding:
BER-TLV:
81
00
03
A0
01
01
33
F9
00
82
02
82
TERMINAL RESPONSE: GET CARD READER STATUS 1.1.1d
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'01'
'Yes'
Yes
'No'
Yes
Yes
Coding:
BER-TLV:
81
00
03
A0
01
01
33
D9
00
ETSI
82
02
82
Release 10
525
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.2 (GET CARD READER STATUS, card reader 1, card inserted, card not powered)
Step
1
2
3
4
5
6
7
8
9
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING: POWER
OFF CARD 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: POWER OFF
CARD 1.2.1
Terminal → SIM2 POWER OFF CARD
Terminal → UICC TERMINAL RESPONSE: POWER OFF CARD
1.2.1
UICC → Terminal PROACTIVE COMMAND PENDING: GET
CARD READER STATUS 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET CARD
READER STATUS 1.1.1
Terminal → UICC TERMINAL RESPONSE: GET CARD
READER STATUS 1.2.1a
Or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.2.1b
or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.2.1c
Or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.2.1d
Comments
Power off card reader 1.
Power off card reader 1.
Successful.
Get Card Reader Status.
Successful.
Successful.
Successful.
Successful.
PROACTIVE COMMAND: POWER OFF CARD 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
UICC
Card reader 1
Coding:
BER-TLV:
D0
09
81
03
01
32
00
82
TERMINAL RESPONSE: POWER OFF CARD 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
POWER OFF CARD
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
02
81
11
Release 10
526
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
00
03
01
32
00
82
02
82
81
83
01
81
83
01
81
83
01
TERMINAL RESPONSE: GET CARD READER STATUS 1.2.1a
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'01'
'No'
Yes
'Yes'
Yes
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
71
00
82
02
82
TERMINAL RESPONSE: GET CARD READER STATUS 1.2.1b
Logically: Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
Command performed successfully
'01'
'No'
Yes
'No'
Yes
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
51
00
ETSI
82
02
82
Release 10
527
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: GET CARD READER STATUS 1.2.1c
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'01'
'Yes'
Yes
'Yes'
Yes
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
79
00
82
02
82
81
83
01
81
83
01
TERMINAL RESPONSE: GET CARD READER STATUS 1.2.1d
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'01'
'Yes'
Yes
'No'
Yes
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
59
00
ETSI
82
02
82
Release 10
528
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.3 (GET CARD READER STATUS, card reader 1, card not present)
Step
1
Direction
SIM2
2
UICC → Terminal
3
4
Terminal → UICC
UICC → Terminal
5
Terminal → UICC
Message/Action
SIM2 is removed from Terminal card
reader
PROACTIVE COMMAND PENDING:
GET CARD READER STATUS 1.1.1
FETCH
PROACTIVE COMMAND: GET CARD
READER STATUS 1.1.1
TERMINAL RESPONSE: GET CARD
READER STATUS 1.3.1a
or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.3.1b
or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.3.1c
or
TERMINAL RESPONSE: GET CARD
READER STATUS 1.3.1d
Comments
Get Card Reader Status.
Successful.
Successful.
Successful.
Successful.
TERMINAL RESPONSE: GET CARD READER STATUS 1.3.1a
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'1'
'No'
Yes
'Yes'
No
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
31
00
82
02
82
TERMINAL RESPONSE: GET CARD READER STATUS 1.3.1b
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
81
83
01
Release 10
529
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'1'
'No'
Yes
'No'
No
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
11
00
82
02
82
81
83
01
81
83
01
TERMINAL RESPONSE: GET CARD READER STATUS 1.3.1c
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
'1'
'Yes'
Yes
'Yes'
No
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
39
00
82
02
82
TERMINAL RESPONSE: GET CARD READER STATUS 1.3.1d
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
530
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
ETSI TS 102 384 V10.3.0 (2015-08)
'1'
'Yes'
Yes
'No'
No
No
Coding:
BER-TLV:
27.22.4.20.1.5
81
00
03
A0
01
01
33
19
00
82
02
82
81
83
01
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.3.
27.22.4.20.2
27.22.4.20.2.1
GET CARD READER STATUS (detachable card reader)
Definition and applicability
See clause 3.2.2.
27.22.4.20.2.2
Conformance requirement
Void.
27.22.4.20.2.3
Test purpose
To verify that the Terminal closes a session with the additional card identified in the GET CARD READER STATUS
proactive UICC command, and successfully returns result in the TERMINAL RESPONSE command send to the UICC.
27.22.4.20.2.4
Method of test
27.22.4.20.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
Prior to this test the Terminal shall have powered on the SIM Simulator (SIM2).
The card reader shall be detached from the Terminal.
27.22.4.20.2.4.2
Procedure
Expected Sequence 2.1 (GET CARD READER STATUS, no card reader attached)
Step
1
2
3
4
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING: GET CARD
READER STATUS 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: GET CARD READER
STATUS 2.1.1
Terminal → UICC TERMINAL RESPONSE: GET CARD READER
STATUS 2.1.1a
or
TERMINAL RESPONSE: GET CARD READER
STATUS 2.1.1b
ETSI
Comments
Get Card Reader Status.
Successful.
Successful.
Release 10
531
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: GET CARD READER STATUS 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card Reader Status
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
33
00
82
02
81
82
81
83
01
TERMINAL RESPONSE: GET CARD READER STATUS 2.1.1a
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
01
Yes
No
Yes
No
No
Coding:
BER-TLV:
81
00
03
A0
01
01
33
29
00
82
02
82
TERMINAL RESPONSE: GET CARD READER STATUS 2.1.1b
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
GET CARD READER STATUS
Card reader status
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
ETSI
Release 10
532
Card reader status
Identity of card reader:
Card reader removable:
Card reader present:
Card reader ID-1 size:
Card present in reader:
Card powered:
ETSI TS 102 384 V10.3.0 (2015-08)
01
Yes
No
No
No
No
Coding:
BER-TLV:
27.22.4.20.2.5
81
00
03
A0
01
01
33
09
00
82
02
82
81
83
01
Test requirement
The Terminal shall operate in the manner defined in expected sequence 2.1.
27.22.4.21
TIMER MANAGEMENT and ENVELOPE TIMER EXPIRATION
27.22.4.21.1
27.22.4.21.1.1
TIMER MANAGEMENT (normal)
Definition and applicability
See clause 3.2.2.
27.22.4.21.1.2
Conformance Requirement
The Terminal shall support the TIMER MANAGEMENT as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.21, 6.8, 8.6, 8.7, 8.37 and 8.38.
27.22.4.21.1.3
Test purpose
To verify that the Terminal manages correctly its internal timers, start a timer, deactivate a timer or return the current
value of a timer according to the Timer Identifier defined in the TIMER MANAGEMENT proactive UICC command.
27.22.4.21.1.4
Method of Test
27.22.4.21.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Toolkit default with the following exceptions.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The Terminal screen shall be in its normal stand-by display.
27.22.4.21.1.4.2
Procedure
Expected Sequence 1.1 (TIMER MANAGEMENT, start timer 1 several times, get the current value of the timer
and deactivate the timer successfully)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.1.1
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.1.1
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.1.2
Terminal → UICC FETCH
ETSI
Comments
Start timer 1.
Command performed successfully.
After 1 minute following reception of Terminal
Response.
Release 10
Step
7
8
9
10
11
12
13
14
15
16
533
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.1.2
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.1.2
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.1.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.1.3
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.1.3
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.1.4
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.1.4
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.1.4
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Ask value of timer 1.
Command performed successfully.
Before timer expires!
Reinitialize timer 1.
Command performed successfully.
After 30 s following reception of the Terminal
Response.
Deactivate timer 1.
Command performed successfully.
PROACTIVE COMMAND: TIMER MANAGEMENT 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Timer value
Value of timer:
5 min
Coding:
BER-TLV:
D0
01
11
01
81
A5
03
03
01
00
27
50
00
00
82
PROACTIVE COMMAND: TIMER MANAGEMENT 1.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
ETSI
02
81
82
A4
Release 10
534
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
01
0C
01
81
03
01
27
02
82
02
81
82
A4
82
02
81
82
A4
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Timer value
Value of timer:
1 min 30 s
Coding:
BER-TLV:
D0
01
11
01
81
A5
03
03
01
00
27
10
00
03
PROACTIVE COMMAND: TIMER MANAGEMENT 1.1.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
D0
01
0C
01
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.1.1 and 1.1.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
535
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
81
A4
03
01
01
01
27
00
82
02
82
81
83
01
00
01
00
01
00
TERMINAL RESPONSE: TIMER MANAGEMENT 1.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
1
Timer value
Value of timer:
value < to the timer value of command 1.1.1
Coding:
BER-TLV:
81
A4
03
01
01
01
27
A5
02
03
82
xx
02
xx
82
xx
81
83
TERMINAL RESPONSE: TIMER MANAGEMENT 1.1.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
1
Timer value
Value of timer:
value < to the timer value of command 1.1.3
Coding:
BER-TLV:
81
A4
03
01
01
01
27
A5
01
03
82
xx
ETSI
02
xx
82
xx
81
83
Release 10
536
ETSI TS 102 384 V10.3.0 (2015-08)
Expected Sequence 1.2 (TIMER MANAGEMENT, start timer 2 several times, get the current value of the timer
and deactivate the timer successfully)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.2.1
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.2.1
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.2.2
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.2.2
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.2.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.2.3
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.2.3
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.2.4
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.2.4
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.2.4
Comments
Start timer 2.
Command performed successfully.
After 1 minute following reception of Terminal
Response.
Ask value of timer 2.
Command performed successfully.
Before timer expires!
Reinitialize timer 2.
Command performed successfully.
After 10 seconds following reception of
Terminal Response
Deactivate timer 2.
Command performed successfully.
PROACTIVE COMMAND:TIMER MANAGEMENT 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
2
Timer value
Value of timer:
23 h 59 min 59 s
Coding:
BER-TLV:
D0
01
11
02
81
A5
03
03
01
32
27
95
ETSI
00
95
82
02
81
82
A4
Release 10
537
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: TIMER MANAGEMENT 1.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
2
Coding:
BER-TLV:
D0
01
0C
02
81
03
01
27
02
82
02
81
82
A4
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.2.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
2
Timer value
Value of timer:
1 min 10 s
Coding:
BER-TLV:
D0
01
11
02
81
A5
03
03
01
00
27
10
00
01
PROACTIVE COMMAND: TIMER MANAGEMENT 1.2.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
2
ETSI
Release 10
538
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
01
0C
02
81
03
01
27
01
82
02
81
82
A4
83
01
00
01
00
TERMINAL RESPONSE: TIMER MANAGEMENT 1.2.1 and 1.2.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
2
Coding:
BER-TLV:
81
A4
03
01
01
02
27
00
82
02
82
81
TERMINAL RESPONSE: TIMER MANAGEMENT 1.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
2
Timer value
Value of timer:
value < to the timer value of command 1.2.1
Coding:
BER-TLV:
81
A4
03
01
01
02
27
A5
02
03
82
xx
ETSI
02
xx
82
xx
81
83
Release 10
539
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.2.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
2
Timer value
Value of timer:
value < to the timer value of command 1.2.3
Coding:
BER-TLV:
81
A4
03
01
01
02
27
A5
01
03
82
xx
02
xx
82
xx
81
83
01
00
Expected Sequence 1.3 (TIMER MANAGEMENT, start timer 8 several times, get the current value of the timer
and deactivate the timer successfully)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.3.1
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.3.1
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.3.2
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.3.2
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.3.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.3.3
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.3.3
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.3.4
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.3.4
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.3.4
ETSI
Comments
Start timer 8.
Command performed successfully.
After 1 minute following reception of Terminal
Response
Ask value of timer 8.
Command performed successfully.
Before timer expires!
Reinitialize timer 8.
Command performed successfully.
After 30 seconds following reception of
Terminal Response.
Deactivate timer 8.
Command performed successfully.
Release 10
540
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND:TIMER MANAGEMENT 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
8
Timer value
Value of timer:
20 min
Coding:
BER-TLV:
D0
01
11
08
81
A5
03
03
01
00
27
02
00
00
82
02
81
82
A4
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
D0
01
0C
08
81
03
01
27
02
PROACTIVE COMMAND: TIMER MANAGEMENT 1.3.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
8
Timer value
Value of timer:
01 h 00 min 00 s
ETSI
82
Release 10
541
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
01
11
08
81
A5
03
03
01
10
27
00
00
00
82
02
81
82
A4
82
02
81
82
A4
83
01
00
PROACTIVE COMMAND: TIMER MANAGEMENT 1.3.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
D0
01
0C
08
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.3.1 and 1.3.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
81
A4
03
01
01
08
27
00
82
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
81
Release 10
542
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
8
Timer value
Value of timer:
value < to the timer value of command 1.3.1
Coding:
BER-TLV:
81
A4
03
01
01
08
27
A5
02
03
82
xx
02
xx
82
xx
81
83
01
00
01
00
TERMINAL RESPONSE: TIMER MANAGEMENT 1.3.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
8
Timer value
Value of timer:
value < to the timer value of command 1.3.3
Coding:
BER-TLV:
81
A4
03
01
01
08
27
A5
01
03
82
xx
02
xx
82
xx
81
83
Expected Sequence 1.4 (TIMER MANAGEMENT, try to get the current value of a timer which is not started:
action in contradiction with the current timer state)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.1
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.1A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.1B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.2
ETSI
Comments
Get current value from timer 1.
Action in contradiction with the current timer
state.
Get current value from timer 2.
Release 10
Step
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
543
Direction
Message/Action
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.2A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.2B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.3
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.3A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.3B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.4
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.4
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.4A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.4B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.5
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.5
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.5A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.5B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.6
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.6
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.6A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.6B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.7
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.7
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.7A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.7B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.4.8
Terminal → UICC FETCH
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Action in contradiction with the current timer
state.
Get current value from timer 3.
Action in contradiction with the current timer
state.
Get current value from timer 4.
Action in contradiction with the current timer
state.
Get current value from timer 5.
Action in contradiction with the current timer
state.
Get current value from timer 6.
Action in contradiction with the current timer
state.
Get current value from timer 7.
Action in contradiction with the current timer
state.
Release 10
Step
31
32
544
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Get current value from timer 8.
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.4.8
Terminal → UICC TERMINAL RESPONSE: TIMER Action in contradiction with the current timer
MANAGEMENT 1.4.8A
state.
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.4.8B
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
D0
01
0C
01
81
03
01
27
02
82
02
81
82
A4
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
81
A4
03
01
01
01
27
02
82
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
ETSI
81
83
01
24
Release 10
545
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
2
Coding:
BER-TLV:
D0
01
0C
02
81
03
01
27
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.2A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
2
Coding:
BER-TLV:
81
A4
03
01
01
02
27
02
82
ETSI
02
82
81
83
01
24
Release 10
546
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.2B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
3
Coding:
BER-TLV:
D0
01
0C
03
81
03
01
27
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.3A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
3
Coding:
BER-TLV:
81
A4
03
01
01
03
27
02
82
ETSI
02
82
81
83
01
24
Release 10
547
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.3B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
4
Coding:
BER-TLV:
D0
01
0C
04
81
03
01
27
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.4A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Timer identifier
Identifier of timer:
Action in contradiction with the current timer state
4
ETSI
Release 10
548
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
81
A4
03
01
01
04
27
02
82
02
82
81
83
01
24
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.4B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.5
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
5
Coding:
BER-TLV:
D0
01
0C
05
81
03
01
27
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.5A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
ETSI
Release 10
549
Timer identifier
Identifier of timer:
ETSI TS 102 384 V10.3.0 (2015-08)
5
Coding:
BER-TLV:
81
A4
03
01
01
05
27
02
82
02
82
81
83
01
24
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.5B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.6
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
6
Coding:
BER-TLV:
D0
01
0C
06
81
03
01
27
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.6A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
Release 10
550
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
6
Coding:
BER-TLV:
81
A4
03
01
01
06
27
02
82
02
82
81
83
01
24
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.6B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Terminal
Destination device:
UICC
General Result:
Action in contradiction with the current timer state
Result
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.7
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
7
Coding:
BER-TLV:
D0
01
0C
07
81
03
01
27
02
82
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.7A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
ETSI
Release 10
551
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
7
Coding:
BER-TLV:
81
A4
03
01
01
07
27
02
82
02
82
81
83
01
24
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.7B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.4.8
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get the current value of the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
D0
01
0C
08
81
03
01
27
02
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.8A
Logically:
Command details
Command number:
Command type:
1
TIMER MANAGEMENT
ETSI
82
Release 10
552
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
81
A4
03
01
01
08
27
02
82
02
82
81
83
01
24
TERMINAL RESPONSE: TIMER MANAGEMENT 1.4.8B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
get current value from the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
02
82
02
82
81
83
01
24
Expected Sequence 1.5 (TIMER MANAGEMENT, try to deactivate a timer which is not started: action in
contradiction with the current timer state)
Step
1
2
3
4
5
6
7
8
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.1
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.1A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.1B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.2
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.2A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.2B
ETSI
Comments
Deactivate timer 1.
Action in contradiction with the current timer
state.
Deactivate timer 2.
Action in contradiction with the current timer
state.
Release 10
Step
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
553
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.3
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.3A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.3B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.4
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.4
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.4A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.4B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.5
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.5
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.5A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.5B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.6
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.6
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.6A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.6B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.7
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.7
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.7A
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.7B
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.5.8
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.5.8
ETSI
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Deactivate timer 3.
Action in contradiction with the current timer
state.
Deactivate timer 4.
Action in contradiction with the current timer
state.
Deactivate timer 5.
Action in contradiction with the current timer
state.
Deactivate timer 6.
Action in contradiction with the current timer
state.
Deactivate timer 7.
Action in contradiction with the current timer
state.
Deactivate timer 8.
Release 10
Step
32
554
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Comments
Terminal → UICC TERMINAL RESPONSE: TIMER Action in contradiction with the current timer
MANAGEMENT 1.5.8A
state.
or
TERMINAL RESPONSE: TIMER
MANAGEMENT 1.5.8B
PROACTIVE COMMAND: TIMER MANAGEMENT 1.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
D0
01
0C
01
81
03
01
27
01
82
02
81
82
A4
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
81
A4
03
01
01
01
27
01
82
02
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
ETSI
82
81
83
01
24
Release 10
555
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
24
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
2
Coding:
BER-TLV:
D0
01
0C
02
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.2A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
2
Coding:
BER-TLV:
81
A4
03
01
01
02
27
01
82
ETSI
02
82
81
83
01
24
Release 10
556
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.2B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
24
82
02
81
82
A4
PROACTIVE COMMAND3: TIMER MANAGEMENT 1.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
3
Coding:
BER-TLV:
D0
01
0C
03
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.3A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
3
Coding:
BER-TLV:
81
A4
03
01
01
03
27
01
82
ETSI
02
82
81
83
01
24
Release 10
557
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.3B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
24
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.5.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
4
Coding:
BER-TLV:
D0
01
0C
04
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.4A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
4
Coding:
BER-TLV:
81
A4
03
01
01
04
27
01
82
ETSI
02
82
81
83
01
24
Release 10
558
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.4B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Terminal
Destination device:
UICC
General Result:
Action in contradiction with the current timer state
Result
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
24
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.5.5
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
5
Coding:
BER-TLV:
D0
01
0C
05
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.5A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
5
Coding:
BER-TLV:
81
A4
03
01
01
05
27
01
82
ETSI
02
82
81
83
01
24
Release 10
559
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.5B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
24
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.5.6
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
6
Coding:
BER-TLV:
D0
01
0C
06
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.6A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
6
Coding:
BER-TLV:
81
A4
03
01
01
06
27
01
82
ETSI
02
82
81
83
01
24
Release 10
560
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.6B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
24
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.5.7
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
7
Coding:
BER-TLV:
D0
01
0C
07
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.7A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
7
Coding:
BER-TLV:
81
A4
03
01
01
07
27
01
82
ETSI
02
82
81
83
01
24
Release 10
561
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.7B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
24
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.5.8
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
deactivate the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
D0
01
0C
08
81
03
01
27
01
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.8A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
81
A4
03
01
01
08
27
01
82
ETSI
02
82
81
83
01
24
Release 10
562
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: TIMER MANAGEMENT 1.5.8B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
Deactivate Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Action in contradiction with the current timer state
Coding:
BER-TLV:
81
03
01
27
01
82
02
82
81
83
01
Expected Sequence 1.6 (TIMER MANAGEMENT, start 8 timers successfully)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.1
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.1
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.2
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.2
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.3
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.3
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.4
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.4
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.4
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.5
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.5
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.5
ETSI
Comments
Timer 1.
Command performed successfully.
Timer 2.
Command performed successfully.
Timer 3.
Command performed successfully.
Timer 4.
Command performed successfully.
Timer 5.
Command performed successfully.
24
Release 10
Step
21
22
23
24
25
26
27
28
29
30
31
32
563
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.6
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.6
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.6
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.7
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.7
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.7
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 1.6.8
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 1.6.8
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 1.6.8
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Timer 6.
Command performed successfully.
Timer 7.
Command performed successfully.
Timer 8.
Command performed successfully.
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Timer value
Value of timer:
5s
Coding:
BER-TLV:
D0
01
11
01
81
A5
03
03
01
00
27
00
00
50
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
82
02
81
82
A4
Release 10
564
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
81
A4
03
01
01
01
27
00
82
02
82
81
83
01
00
82
02
81
82
A4
83
01
00
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
2
Timer value
Value of timer:
5s
Coding:
BER-TLV:
D0
01
11
02
81
A5
03
03
01
00
27
00
00
50
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
2
Coding:
BER-TLV:
81
A4
03
01
01
02
27
00
82
ETSI
02
82
81
Release 10
565
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
3
Timer value
Value of timer:
5s
Coding:
BER-TLV:
D0
01
11
03
81
A5
03
03
01
00
27
00
00
50
82
02
81
82
A4
83
01
00
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
3
Coding:
BER-TLV:
81
A4
03
01
01
03
27
00
82
02
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
4
ETSI
82
81
Release 10
566
Timer value
Value of timer:
ETSI TS 102 384 V10.3.0 (2015-08)
5s
Coding:
BER-TLV:
D0
01
11
04
81
A5
03
03
01
00
27
00
00
50
82
02
81
82
A4
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.4
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
Coding:
BER-TLV:
81
A4
4
03
01
01
04
27
00
82
02
82
81
83
01
00
82
02
81
82
A4
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.5
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
5
Timer value
Value of timer:
5s
Coding:
BER-TLV:
D0
01
11
05
81
A5
03
03
01
00
27
00
00
50
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.5
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
ETSI
Release 10
567
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
5
Coding:
BER-TLV:
81
A4
03
01
01
05
27
00
82
02
82
81
83
01
00
82
02
81
82
A4
83
01
00
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.6
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
6
Timer value
Value of timer:
5s
Coding:
BER-TLV:
D0
01
11
06
81
A5
03
03
01
00
27
00
00
50
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.6
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
6
Coding:
BER-TLV:
81
A4
03
01
01
06
27
00
82
ETSI
02
82
81
Release 10
568
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.7
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
7
Timer value
Value of timer:
5s
Coding:
BER-TLV:
D0
01
11
07
81
A5
03
03
01
00
27
00
00
50
82
02
81
82
A4
83
01
00
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.7
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
7
Coding:
BER-TLV:
81
A4
03
01
01
07
27
00
82
02
PROACTIVE COMMAND: TIMER MANAGEMENT 1.6.8
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
8
ETSI
82
81
Release 10
569
Timer value
Value of timer:
ETSI TS 102 384 V10.3.0 (2015-08)
5s
Coding:
BER-TLV:
D0
01
11
08
81
A5
03
03
01
00
27
00
00
50
82
02
81
82
A4
83
01
00
TERMINAL RESPONSE: TIMER MANAGEMENT 1.6.8
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
8
Coding:
BER-TLV:
27.22.4.21.1.5
81
A4
03
01
01
08
27
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.6.
27.22.4.21.2
27.22.4.21.2.1
ENVELOPE TIMER EXPIRATION (normal)
Definition and applicability
See clause 3.2.2.
27.22.4.21.2.2
Conformance requirement
The Terminal shall support the ENVELOPE (TIMER EXPIRATION) command as defined in the following technical
specifications:
•
ETSI TS 102 223 [1], clauses 4.10, 7.4.1 and 7.4.2.
The Terminal shall support the TIMER MANAGEMENT as defined in the following technical specifications:
•
ETSI TS 102 223 [1], clauses 5.2, 6.4.21, 6.8, 8.6, 8.7, 8.37 and 8.38.
27.22.4.21.2.3
Test purpose
To verify that the Terminal shall pass the identifier of the timer that has expired and its value using the ENVELOPE
(TIMER EXPIRATION) command, when a timer previously started in a TIMER MANAGEMENT proactive command
expires.
27.22.4.21.2.4
Method of test
27.22.4.21.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
ETSI
Release 10
570
ETSI TS 102 384 V10.3.0 (2015-08)
The elementary files are coded as Card Application Toolkit default with the following exceptions.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
The timer 1 is not started.
When the UICC is busy when the envelope TIMER EXPIRATION is sent, either the Terminal retries periodically to
send the envelope, either it waits for a TERMINAL RESPONSE processed by the UICC with status '90 00'.
If the Terminal waits for a TR with status '90 00', the Terminal manufacturer shall specify how many TERMINAL
RESPONSES with status '90 00' are expected before sending the TIMER EXPIRATION envelope.
27.22.4.21.2.4.2
Procedure
Expected Sequence 2.1 (TIMER EXPIRATION, pending proactive UICC command)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: TIMER Timer 1.
MANAGEMENT 2.1.1
Command performed successfully.
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 2.1.1
Terminal → UICC ENVELOPE: TIMER EXPIRATION
2.1.1
Response to envelope is "91 xx".
UICC → Terminal PROACTIVE COMMAND
PENDING: MORE TIME X.1(or an
other toolkit command tested
before to ensure it is properly
supported by the Terminal).
Terminal → UICC FETCH
PROACTIVE COMMAND: TIMER MANAGEMENT 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Timer value
Value of timer:
0 h 0 min 10 s
Coding:
BER-TLV:
D0
01
11
01
81
A5
03
03
01
00
27
00
00
01
TERMINAL RESPONSE: TIMER MANAGEMENT 2.1.1
Logically:
Command details
Command number:
Command type:
1
TIMER MANAGEMENT
ETSI
82
02
81
82
A4
Release 10
571
Command qualifier:
ETSI TS 102 384 V10.3.0 (2015-08)
start the Timer
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
81
A4
03
01
01
01
27
00
82
02
82
81
83
01
00
81
A4
01
01
A5
03
00
ENVELOPE: TIMER EXPIRATION 2.1.1
Logically:
Device identities
Source device:
Destination device:
Terminal
UICC
Timer identifier
Timer 1
Timer value
Hour:
Minute:
Second:
'00'
'00'
'10' ± 1 s
Coding:
BER-TLV:
D7
00
0C
xx
82
02
82
Expected Sequence 2.2 (TIMER EXPIRATION, UICC application toolkit busy)
Step
1
2
3
4
5
6
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: TIMER
MANAGEMENT 2.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
TIMER MANAGEMENT 2.2.1
Terminal → UICC TERMINAL RESPONSE: TIMER
MANAGEMENT 2.2.1
Terminal → UICC ENVELOPE: TIMER
EXPIRATION 2.2.1A
UICC → Terminal PROACTIVE UICC SESSION
BUSY
...
7a
Terminal → UICC ENVELOPE: TIMER
EXPIRATION
2.2.1B
ETSI
Comments
[timer 1]
[command performed successfully]
[UICC is busy; response to the envelope = "93
00"]
[UICC is busy during 10 seconds, if the
terminal periodically retries to send of the
envelope until it is accepted, then step 7a-10a
apply. If the terminal does not periodically
retry to send the envelope, e.g. it waits for a
TERMINAL RESPONSE processed by the
UICC with status '90 00', then step 7b - 14b
apply]
[Branch applies for terminals periodically
retrying to send the envelope]
Release 10
Step
8a
9a
10a
7b
8b
9b
10b
11b
12b
13b
14b
572
Direction
Message/Action
UICC → Terminal PROACTIVE UICC SESSION
BUSY
Terminal → UICC ENVELOPE: TIMER
EXPIRATION 2.2.1C
UICC → Terminal SW1/SW2=90 00
Terminal → UICC STATUS or other command
UICC → Terminal Response to the command
issued in step 7b
PROACTIVE COMMAND
PENDING
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: e.g.
MORE TIME 2.2.2
Terminal → UICC TERMINAL RESPONSE: e.g.
MORE TIME 2.2.2
UICC → Terminal Response to the command
issued in step 11b
Terminal → UICC ENVELOPE: TIMER
EXPIRATION 2.2.1B
UICC → Terminal SW1/SW2=90 00
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
[UICC is busy, response to the envelope = "93
00"]
[Branch applies for terminals not periodically
retrying to send the envelope (in compliance
with ETSI TS 101 267 [11], clause 10.1)]
Steps 7b - 12b are repeated maximal
100 times (to prevent infinite testing) or until
the terminals sends ENVELOPE: TIMER
EXPIRATION 2.2.1B in step 13b or at any
time during steps 7b - 12b (in latter case
step 13b is obsolete).
[SW1/SW2=91 xx]
[command performed successfully]
[SW1/SW2 = 90 00]
PROACTIVE COMMAND: TIMER MANAGEMENT 2.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
Device identities
Source device:
Destination device:
UICC
Terminal
Timer identifier
Identifier of timer:
1
Timer value
Value of timer:
0 h 0 min 30 s
Coding:
BER-TLV:
D0
01
11
01
81
A5
03
03
01
00
27
00
00
03
TERMINAL RESPONSE: TIMER MANAGEMENT 2.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
TIMER MANAGEMENT
start the Timer
ETSI
82
02
81
82
A4
Release 10
573
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Timer identifier
Identifier of timer:
1
Coding:
BER-TLV:
81
A4
03
01
01
01
27
00
82
02
82
81
83
01
00
81
A4
01
01
A5
03
00
01
01
A5
03
00
ENVELOPE: TIMER EXPIRATION 2.2.1A
Logically:
Device identities
Source device:
Destination device:
Terminal
UICC
Timer identifier
Timer 1
Timer value
Hour:
Minute:
Second:
'00'
'00'
'30' ± 1 s
Coding:
BER-TLV:
D7
00
0C
xx
82
02
82
ENVELOPE: TIMER EXPIRATION 2.2.1B
Logically:
Device identities
Source device:
Destination device:
Terminal
UICC
Timer identifier
Timer 1
Timer value
Hour:
Minute:
Second:
'00'
'00'
≥ timer in clause 2.2.1A
Coding:
BER-TLV:
D7
00
0C
xx
82
02
82
81
ETSI
A4
Release 10
574
ETSI TS 102 384 V10.3.0 (2015-08)
ENVELOPE: TIMER EXPIRATION 2.2.1C
Logically:
Device identities
Source device:
Destination device:
Terminal
UICC
Timer identifier
Timer 1
Timer value
Hour:
Minute:
Second:
'00'
'00'
≥ timer in 2.2.1B
Coding:
BER-TLV:
D7
00
0C
xx
82
02
82
81
A4
01
01
A5
03
00
PROACTIVE COMMAND: MORE TIME 2.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
MORE TIME
"00"
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
02
00
82
02
81
82
TERMINAL RESPONSE: MORE TIME 2.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
MORE TIME
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.21.2.5
81
03
01
02
00
82
02
82
Test requirement
The Terminal shall operate in the manner defined in expected sequences 2.1 to 2.2.
ETSI
81
83
01
00
Release 10
575
27.22.4.22
ETSI TS 102 384 V10.3.0 (2015-08)
SET UP IDLE MODE TEXT
27.22.4.22.1
27.22.4.22.1.1
SET UP IDLE MODE TEXT (normal)
Definition and applicability
See clause 3.2.2.
27.22.4.22.1.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 6.4.7 and
6.6.13.
Additionally the Terminal shall support the REFRESH proactive UICC facility as defined in:
•
ETSI TS 102 223 [1], clauses 5.2, 6.1, 6.4.7, 6.6.13, 6.11, 8.6, 8.7, 8.12, 9.4 and 10.
27.22.4.22.1.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text.
27.22.4.22.1.4
Method of test
27.22.4.22.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on, performed the PROFILE DOWNLOAD procedure.
27.22.4.22.1.4.2
Procedure
Expected Sequence 1.1 (SET UP IDLE MODE TEXT, display idle mode text)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 1.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
Display
"Idle
Mode
Text"
Terminal → USER
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text"
ETSI
Release 10
576
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
0F
54
1A
04
65
81
49
78
03
64
74
01
6C
28
65
00
20
82
4D
02
6F
81
64
82
65
8D
20
83
01
00
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 1.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
Expected Sequence 1.2 (SET UP IDLE MODE TEXT, replace idle mode text)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 1.1.1
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 1.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.2.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 1.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Toolkit Test"
Comments
Idle Mode Text.
Only if idle screen not already available.
Idle Mode Text.
Idle Mode Text.
Only if idle screen not already available.
PROACTIVE COMMAND: SETUP IDLE MODE TEXT 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SETUP IDLE MODE TEXT
RFU
ETSI
Release 10
577
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
UICC
ME
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Toolkit Test"
Coding:
BER-TLV:
D0
0D
73
18
04
74
81
54
03
6F
01
6F
28
6C
00
6B
82
69
02
74
81
20
82
54
8D
65
83
01
00
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 1.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
Expected Sequence 1.3 (SET UP IDLE MODE TEXT, remove idle mode text)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND PENDING:
SET UP IDLE MODE TEXT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 1.1.1
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text"
UICC → Terminal PROACTIVE COMMAND PENDING:
SET UP IDLE MODE TEXT 1.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.3.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 1.3.1
UICC → Terminal PROACTIVE UICC SESSION ENDED
USER → Terminal Select idle screen
Terminal → USER Display idle screen/"Idle Mode Text"
not to be displayed
ETSI
Comments
"Idle Mode Text".
Only if idle screen not already available.
Remove idle mode text.
Only if idle screen not already available.
Release 10
578
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SETUP IDLE MODE TEXT 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SETUP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Text string
UICC
Terminal
zero length TLV
Coding:
BER-TLV:
D0
00
0B
81
03
01
28
00
82
02
81
82
8D
83
01
00
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 1.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
Expected Sequence 1.4 (SET UP IDLE MODE TEXT, competing information on Terminal display)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 1.1.1
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text"
UICC → Terminal PROACTIVE COMMAND
PENDING: DISPLAY TEXT 1.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
DISPLAY TEXT 1.4.1
Terminal → USER Display "Toolkit Test 1"
USER → Terminal Clear Message
Terminal → UICC TERMINAL RESPONSE:
DISPLAY TEXT 1.4.1
Terminal → USER Display "Idle Mode Text"
UICC → Terminal PROACTIVE COMMAND
PENDING: PLAY TONE 1.4.1
ETSI
Comments
"Idle Mode Text".
Command performed successfully.
Only if idle screen not already available.
Normal priority, wait for user to clear
message, unpacked, 8 bit data.
Command performed successfully.
Release 10
Step
15
16
17
18
19
20
579
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: PLAY
TONE 1.4.1
Terminal → USER Display "Dial Tone"
Comments
Play a standard supervisory dial
tone through the external ringer for
a duration of 5 s
Command performed successfully.
Terminal → UICC TERMINAL RESPONSE: PLAY
TONE 1.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Terminal → USER Display "Idle Mode Text"
PROACTIVE COMMAND: DISPLAY TEXT 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
UICC
Display
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Toolkit Test 1"
Coding:
BER-TLV:
D0
0F
73
1A
04
74
81
54
20
03
6F
31
01
6F
21
6C
80
6B
82
69
02
74
81
20
02
54
8D
65
01
00
TERMINAL RESPONSE: DISPLAY TEXT 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
DISPLAY TEXT
normal priority, wait for user to clear message
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
21
80
82
ETSI
02
82
81
83
Release 10
580
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: PLAY TONE 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Alpha identifier:
Tone:
UICC
Earpiece
"Dial Tone"
Standard supervisory tones: dial tone
Duration
Time unit:
Time interval:
Seconds
5
Coding:
BER-TLV:
D0
09
01
1B
44
84
81
69
02
03
61
01
01
6C
05
20
20
00
54
82
6F
02
6E
81
65
03
8E
85
01
83
01
00
TERMINAL RESPONSE: PLAY TONE 1.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
PLAY TONE
"00"
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
20
00
82
02
82
81
Expected Sequence 1.5 (SET UP IDLE MODE TEXT, Terminal power cycled)
Step
1
2
3
4
5
6
7
8
9
10
Direction
Message/Action
Comments
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP "Idle Mode Text".
IDLE MODE TEXT 1.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 1.1.1
Only if idle screen not already available.
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text"
USER → Terminal Power off Terminal
Terminal ⇔ UICC NAA Session TERMINATION
PROCEDURE
USER → Terminal Power on Terminal
Terminal ⇔ UICC NAA Session ACTIVATION
PROCEDURE
ETSI
Release 10
Step
11
12
13
581
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
Terminal ⇔ UICC NAA INITIALIZATION
USER → Terminal Select idle screen
Terminal → USER Display idle screen/"Idle Mode
Text" not to be displayed
Comments
Only if idle screen not already available.
Expected Sequence 1.6 (SET UP IDLE MODE TEXT, REFRESH with NAA Initialization)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 1.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 1.1.1
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text"
UICC → Terminal PROACTIVE COMMAND
PENDING: REFRESH 1.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND:
REFRESH 1.6.1
Terminal ⇔ UICC NAA INITIALIZATION
USER → Terminal Select idle screen
Terminal → USER Display idle screen/"Idle Mode
Text" not to be displayed
Terminal → UICC TERMINAL RESPONSE:
REFRESH 1.6.1A
or
TERMINAL RESPONSE:
REFRESH 1.6.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Comments
Idle Mode Text.
Only if idle screen not already available.
NAA Initialization.
Only if idle screen not already available.
Command performed successfully.
Command performed successfully with
additional files read.
PROACTIVE COMMAND: REFRESH 1.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
REFRESH
NAA Initialization
Device identities
Source device:
Destination device:
UICC
Terminal
Coding:
BER-TLV:
D0
09
81
03
01
01
TERMINAL RESPONSE: REFRESH 1.6.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
REFRESH
NAA Initialization
ETSI
03
82
02
81
82
Release 10
582
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
01
03
82
02
82
81
83
01
00
01
03
TERMINAL RESPONSE: REFRESH 1.6.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
REFRESH
NAA Initialization
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
REFRESH performed with additional EFs read
Coding:
BER-TLV:
81
03
01
01
03
82
02
82
81
83
Expected Sequence 1.7 (SET UP IDLE MODE TEXT, large text string)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 1.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 1.7.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 1.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "The SIM shall supply a
text string, which shall be
displayed by the ME as an idle
mode text if the ME is able to do it.
The presentation style is left as an
implementation decision to the ME
manufacturer. The idle mode text
shall be displayed in a manner that
ensures that ne"
Comments
Large text string.
Command performed successfully.
Only if idle screen not already available.
274 characters.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 1.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
ETSI
Release 10
583
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
UICC
Terminal
Text String
Data coding scheme:
Text:
packed, SMS default alphabet
"The SIM shall supply a text string, which shall be displayed by the
ME as an idle mode text if the ME is able to do it. The presentation
style is left as an implementation decision to the ME manufacturer.
The idle mode text shall be displayed in a manner that ensures that ne"
Coding:
BER-TLV:
D0
8D
74
E8
47
88
74
93
94
B0
A8
7E
D9
E5
A7
59
B9
C9
12
DA
61
D3
81
81
98
65
A7
9C
74
D9
36
98
E8
BB
4C
76
E7
04
0B
65
97
0D
3A
41
FD
F1
CD
3C
C7
9E
19
65
83
5D
32
41
07
D9
E9
B5
44
10
41
0A
A8
EE
81
00
06
1D
68
C3
D4
50
E8
06
08
73
85
4D
B7
C3
45
BD
E4
83
EC
32
03
54
CD
34
D0
D9
2C
FB
E8
D1
2E
7A
E7
0F
1B
EE
97
8C
F4
DA
9E
01
74
EB
A7
1C
E1
82
4D
32
DF
2F
9E
A0
D3
44
BA
41
A7
1C
61
D7
28
19
70
CB
1D
7C
C2
2E
A8
20
CF
5D
B0
D3
7F
39
69
83
CE
B7
E5
00
34
38
D3
66
99
73
83
59
F2
CB
06
1B
6F
83
3C
32
E6
0E
BB
E5
82
4D
3B
EE
B3
0C
50
E8
04
1B
6E
A5
94
37
E8
A6
BB
E8
E7
2C
39
02
36
0F
33
41
12
D8
65
A5
94
7A
E7
6E
88
E8
D7
0C
30
CB
07
88
81
41
0A
0B
E2
E7
0D
3C
E7
A6
98
20
C3
5C
32
E5
6A
9B
64
D1
8E
82
73
83
74
32
41
4A
1D
A0
BB
9E
76
D9
1E
A8
65
BF
0D
50
D1
0E
83
01
00
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 1.7.1
Logically:
Command details
Command number:
Command type:
Command q qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.1.5
81
03
01
28
00
82
02
82
Test requirement
The Terminal shall operate in the manner defined in expected sequences 1.1 to 1.7.
ETSI
81
Release 10
584
27.22.4.22.2
27.22.4.22.2.1
ETSI TS 102 384 V10.3.0 (2015-08)
SET UP IDLE MODE TEXT (Icon support)
Definition and applicability
See clause 3.2.2.
27.22.4.22.2.2
Conformance requirement
27.22.4.22.2.3
Test purpose
To verify that the Terminal text and/or icon passed to the Terminal is displayed by the Terminal as an idle mode text.
To verify that the icon identifier provided with the text string can replace the text string or accompany it.
To verify that if both an alpha identifier or text string, and an icon are provided with a proactive command, and both are
requested to be displayed, but the Terminal is not able to display both together on the screen, then the alpha identifier or
text string takes precedence over the icon.
To verify that if the UICC provides an icon identifier with a proactive command, then the Terminal shall inform the
UICC if the icon could not be displayed by sending the general result "Command performed successfully, but requested
icon could not be displayed".
To verify that if the Terminal receives an icon identifier with a proactive command and either an empty, or no alpha
identifier/text string is given by the UICC, than the Terminal shall reject the command with general result "Command
data not understood by Terminal".
27.22.4.22.2.4
Method of test
27.22.4.22.2.4.1
Initial conditions
The Terminal is connected to both the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.2.4.2
Procedure
Expected Sequence 2.1A (SET UP IDLE MODE TEXT, Icon is self-explanatory, successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
Icon is self-explanatory.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 2.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 2.1.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display the icon
Only if idle screen not already available.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 2.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
ETSI
Release 10
585
ETSI TS 102 384 V10.3.0 (2015-08)
Device identities
Source device:
Destination device:
Text string
UICC
Terminal
"Idle text"
Icon identifier
Icon qualifier:
Icon identifier:
icon is self-explanatory
<record 1 in EF IMG>
Coding:
BER-TLV:
D0
0A
02
19
04
00
81
49
01
03
64
01
6C
28
65
00
20
82
74
02
65
81
78
82
74
8D
9E
83
01
00
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 2.1.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
Expected Sequence 2.1B (SET UP IDLE MODE TEXT, Icon is self-explanatory, requested icon could not be
displayed)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 2.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 2.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 2.1.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle text" without the icon
Comments
Icon is self-explanatory.
Command performed successfully, but
requested icon could not be displayed.
Only if idle screen not already available.
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 2.1.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Terminal
ETSI
Release 10
586
ETSI TS 102 384 V10.3.0 (2015-08)
Destination device:
UICC
General Result:
Command performed successfully, but requested icon could not be
displayed
Result
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
83
01
04
Expected Sequence 2.2A (SET UP IDLE MODE TEXT, Icon is not self-explanatory, successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
Icon is not self-explanatory.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 2.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 2.2.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 2.2.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
Display
icon
#1
and
"Idle
text"
Terminal → USER
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 2.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Text string
UICC
Terminal
"Idle text"
Icon identifier
Icon qualifier:
Icon identifier:
icon is not self-explanatory
<record 1 in EF IMG>
Coding:
BER-TLV:
D0
0A
02
19
04
01
81
49
01
03
64
01
6C
28
65
00
20
82
74
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 2.2.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
ETSI
02
65
81
78
82
74
8D
9E
Release 10
587
ETSI TS 102 384 V10.3.0 (2015-08)
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
83
01
00
Expected Sequence 2.2B (SET UP IDLE MODE TEXT, Icon is not self-explanatory, requested icon could not be
displayed)
Step
1
2
3
4
5
6
7
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 2.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 2.2.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 2.2.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle text" without the icon
Comments
Icon is not self-explanatory.
Command performed successfully, but
requested icon could not be displayed.
Only if idle screen not already available.
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 2.2.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully, but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
83
01
04
Expected Sequence 2.3A (SET UP IDLE MODE TEXT, Icon is self-explanatory, colour icon, successful)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
Icon is self-explanatory.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 2.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 2.3.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 2.3.1A
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
Terminal → USER Display the icon
ETSI
Release 10
588
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 2.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Text string
UICC
Terminal
"Idle text"
Icon identifier
Icon qualifier:
Icon identifier:
icon is self-explanatory
<record 2 in EF IMG>
Coding:
BER-TLV:
D0
0A
02
19
04
00
81
49
02
03
64
01
6C
28
65
00
20
82
74
02
65
81
78
82
74
8D
9E
83
01
00
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 2.3.1A
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
Expected Sequence 2.3B (SET UP IDLE MODE TEXT, Icon is self-explanatory, colour icon, requested icon
could not be displayed)
Step
1
2
3
4
5
6
7
Direction
Message/Action
Comments
Icon is self-explanatory.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 2.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 2.3.1
Terminal → UICC TERMINAL RESPONSE: SET UP Requested icon could not be displayed.
IDLE MODE TEXT 2.3.1B
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
Terminal → USER Display 'Idle text' without the icon
ETSI
Release 10
589
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 2.3.1B
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully, but requested icon could not be
displayed
Coding:
BER-TLV:
81
03
01
28
00
82
02
82
81
83
01
04
Expected Sequence 2.4 (SET UP IDLE MODE TEXT, Icon is not self-explanatory, empty text string)
Step
1
2
3
4
5
Direction
Message/Action
Comments
Icon is not self-explanatory, empty text string.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 2.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 2.4.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 2.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 2.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text string
Contents:
null data object
Icon identifier
Icon qualifier:
Icon identifier:
icon is not self-explanatory
<record 1 in EF IMG>
Coding:
BER-TLV:
D0
00
0F
9E
81
02
03
01
01
01
28
ETSI
00
82
02
81
82
8D
Release 10
590
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 2.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command data not understood by Terminal
Coding:
BER-TLV:
27.22.4.22.2.5
81
03
01
28
00
82
02
82
81
83
01
32
Test requirement
The Terminal shall operate in the manner defined in expected sequences 2.1A to 2.4.
27.22.4.22.3
27.22.4.22.3.1
SET UP IDLE MODE TEXT (UCS2 display in Cyrillic)
Definition and applicability
See clause 3.2.2.
27.22.4.22.3.2
Conformance requirement
The Terminal shall support the UCS2 facility for the coding of the Cyrillic alphabet, as defined in:
•
ISO/IEC 10646 [2].
27.22.4.22.3.3
Test purpose
To verify that the UCS2 coded text string is displayed by the Terminal as an idle mode text.
27.22.4.22.3.4
Method of test
27.22.4.22.3.4.1
Initial conditions
The Terminal is connected to both the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.3.4.2
Procedure
Expected Sequence 3.1 (SET UP IDLE MODE TEXT, UCS2 alphabet text in Cyrillic)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
"Hello" in Russian.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 3.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 3.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 3.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
ETSI
Release 10
Step
7
591
Direction
Message/Action
Terminal → USER Display " ЗДРАВСТВУЙТЕ"
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
"Hello" in Russian.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
UCS2 (16bit)
"ЗДРАВСТВУЙТЕ"
Coding:
BER-TLV:
D0
19
04
04
24
08
21
15
81
04
04
03
17
22
01
04
04
28
14
12
00
04
04
82
20
23
02
04
04
81
10
19
82
04
04
8D
12
22
83
01
00
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 3.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.3.5
81
03
01
28
00
82
02
82
81
Test requirement
The Terminal shall operate in the manner defined in expected sequence 3.1.
27.22.4.22.4
SET UP IDLE MODE TEXT (support of Text Attribute)
27.22.4.22.4.1
SET UP IDLE MODE TEXT (support of Text Attribute - Left Alignment)
27.22.4.22.4.1.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.1.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
ETSI
Release 10
592
27.22.4.22.4.1.3
ETSI TS 102 384 V10.3.0 (2015-08)
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the left alignment text attribute
configuration.
27.22.4.22.4.1.4
Method of test
27.22.4.22.4.1.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.1.4.2
Procedure
Expected Sequence 4.1 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Left Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.1.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.1.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.1.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.1.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.1.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
Comments
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with left alignment.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available
Message shall be formatted without left
alignment. Remark: If left alignment is the
Terminal's default alignment as declared in
table A.2/15, no alignment change will take
place.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
ETSI
Release 10
593
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
ETSI TS 102 384 V10.3.0 (2015-08)
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
00
8D
20
B4
02
6F
81
64
82
65
8D
20
83
01
00
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.1.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
00
20
82
4D
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.1.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.1.5
81
03
01
28
00
82
02
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.1.
ETSI
82
81
Release 10
594
ETSI TS 102 384 V10.3.0 (2015-08)
27.22.4.22.4.2
SET UP IDLE MODE TEXT (support of Text Attribute - Center Alignment)
27.22.4.22.4.2.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.2.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.2.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the center alignment text
attribute configuration.
27.22.4.22.4.2.4
Method of test
27.22.4.22.4.2.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.2.4.2
Procedure
Expected Sequence 4.2 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Center Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.2.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.2.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.2.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.2.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.2.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
ETSI
Comments
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with center alignment.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available
Message shall be formatted without center
alignment. Remark: If center alignment is the
Terminal's default alignment as declared in
table A.2/15, no alignment change will take
place.
Release 10
595
ETSI TS 102 384 V10.3.0 (2015-08)
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Center Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
01
8D
20
B4
02
6F
81
64
82
65
8D
20
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.2.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
00
20
82
4D
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.2.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
ETSI
Release 10
596
Device identities
Source device:
Destination device:
ETSI TS 102 384 V10.3.0 (2015-08)
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.2.5
81
03
01
28
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.2.
27.22.4.22.4.3
SET UP IDLE MODE TEXT (support of Text Attribute - Right Alignment)
27.22.4.22.4.3.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.3.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.3.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the right alignment text
attribute configuration.
27.22.4.22.4.3.4
Method of test
27.22.4.22.4.3.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.3.4.2
Procedure
Expected Sequence 4.3 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Right Alignment)
Step
1
2
3
4
5
6
7
8
9
10
11
Direction
Message/Action
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.3.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.3.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.3.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.3.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.3.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.3.1
ETSI
Comments
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with right alignment.
Idle Mode Text.
Command performed successfully.
Release 10
Step
12
13
14
597
ETSI TS 102 384 V10.3.0 (2015-08)
Direction
Message/Action
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
Comments
Only if idle screen not already available
Message shall be formatted without right
alignment. Remark: If right alignment is the
Terminal's default alignment as declared in
table A.2/15, no alignment change will take
place.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Right Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
02
8D
20
B4
02
6F
81
64
82
65
8D
20
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.3.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
ETSI
00
20
82
4D
Release 10
598
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.3.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.3.5
81
03
01
28
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.3.
27.22.4.22.4.4
SET UP IDLE MODE TEXT (support of Text Attribute - Large Font Size)
27.22.4.22.4.4.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.4.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.4.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the large font size text attribute
configuration.
27.22.4.22.4.4.4
Method of test
27.22.4.22.4.4.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.4.4.2
Procedure
Expected Sequence 4.4 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Large Font Size)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
Idle Mode Text.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.4.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
ETSI
Release 10
Step
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
599
Direction
Message/Action
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.4.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.4.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.4.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.4.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.4.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.4.3
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.4.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 3"
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Text is displayed with large font size.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available
Text is displayed with normal font size.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available
Text is displayed with large font size.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with normal font size.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Large Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
600
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
04
8D
20
B4
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.4.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
00
8D
20
B4
02
6F
81
64
82
65
8D
20
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.4.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 3"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
33
ETSI
00
20
82
4D
Release 10
601
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.4.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.4.5
81
03
01
28
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.4.
27.22.4.22.4.5
SET UP IDLE MODE TEXT (support of Text Attribute - Small Font Size)
27.22.4.22.4.5.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.5.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.5.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the small font size text
attribute configuration.
27.22.4.22.4.5.4
Method of test
27.22.4.22.4.5.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.5.4.2
Procedure
Expected Sequence 4.5 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Small Font Size)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
Idle Mode Text.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.5.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
ETSI
Release 10
Step
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
602
Direction
Message/Action
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.5.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.5.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.5.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.5.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.5.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.5.3
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.5.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text" 3
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Text is displayed with small font size.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with normal font size.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with small font size.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with normal font size.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Small Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
603
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
08
8D
20
B4
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.5.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough
Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
00
8D
20
B4
02
6F
81
64
82
65
8D
20
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.5.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 3"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
33
ETSI
00
20
82
4D
Release 10
604
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.5.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.5.5
81
03
01
28
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.5.
27.22.4.22.4.6
SET UP IDLE MODE TEXT (support of Text Attribute - Bold On)
27.22.4.22.4.6.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.6.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.6.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the bold text attribute
configuration.
27.22.4.22.4.6.4
Method of test
27.22.4.22.4.6.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.6.4.2
Procedure
Expected Sequence 4.6 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Bold On)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
Idle Mode Text.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.6.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 4.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available
USER → Terminal Select idle screen
ETSI
Release 10
Step
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
605
Direction
Message/Action
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.6.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.6.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.6.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.6.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.6.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.6.3
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.6.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 3"
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Text is displayed with bold on.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with bold off.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with bold on.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with bold off.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Normal Font, Bold On, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
606
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
10
8D
20
B4
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.6.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
00
8D
20
B4
02
6F
81
64
82
65
8D
20
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.6.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 3"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
33
ETSI
00
20
82
4D
Release 10
607
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.6.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.6.5
81
03
01
28
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.6.
27.22.4.22.4.7
SET UP IDLE MODE TEXT (support of Text Attribute - Italic On)
27.22.4.22.4.7.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.7.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.7.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the italic text attribute
configuration.
27.22.4.22.4.7.4
Method of test
27.22.4.22.4.7.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.7.4.2
Procedure
Expected Sequence 4.7 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Italic On)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
Idle Mode Text.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.7.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 4.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
ETSI
Release 10
Step
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
608
Direction
Message/Action
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.7.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.7.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.7.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.7.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.7.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.7.3
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.7.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 3"
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Text is displayed with italic on.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with italic off.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with italic on.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with italic off.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Normal Font, Bold Off, Italic On, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
609
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
20
8D
20
B4
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.7.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
00
8D
20
B4
02
6F
81
64
82
65
8D
20
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.7.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 3"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
33
ETSI
00
20
82
4D
Release 10
610
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.7.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.7.5
81
03
01
28
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.7.
27.22.4.22.4.8
SET UP IDLE MODE TEXT (support of Text Attribute - Underline On)
27.22.4.22.4.8.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.8.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.8.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the underline text attribute
configuration.
27.22.4.22.4.8.4
Method of test
27.22.4.22.4.8.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.8.4.2
Procedure
Expected Sequence 4.8 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Underline On)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
Idle Mode Text.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.8.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 4.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
ETSI
Release 10
Step
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
611
Direction
Message/Action
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.8.2
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.8.2
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 2"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.8.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.8.1
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 1"
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.8.3
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.8.3
Terminal → UICC TERMINAL RESPONSE: SET UP
IDLE MODE TEXT 4.8.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
USER → Terminal Select idle screen
Terminal → USER Display "Idle Mode Text 3"
ETSI TS 102 384 V10.3.0 (2015-08)
Comments
Text is displayed with underline on.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with underline off.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with underline on.
Idle Mode Text.
Command performed successfully.
Only if idle screen not already available.
Text is displayed with underline off.
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 1"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
Colour:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline On,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
ETSI
Release 10
612
ETSI TS 102 384 V10.3.0 (2015-08)
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
31
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
40
8D
20
B4
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.8.2
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 2"
Text Attribute
Formatting position:
Formatting length:
Formatting mode:
0
16
Left Alignment, Normal Font, Bold Off, Italic Off, Underline Off,
Strikethrough Off
Dark Green Foreground, Bright Yellow Background
Colour:
Coding:
BER-TLV:
D0
11
54
22
04
65
81
49
78
03
64
74
01
6C
20
28
65
32
00
20
D0
82
4D
04
02
6F
00
81
64
10
82
65
00
8D
20
B4
02
6F
81
64
82
65
8D
20
PROACTIVE COMMAND: SET UP IDLE MODE TEXT 4.8.3
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
UICC
Terminal
Text String
Data coding scheme:
Text:
unpacked, 8 bit data
"Idle Mode Text 3"
Coding:
BER-TLV:
D0
11
54
1C
04
65
81
49
78
03
64
74
01
6C
20
28
65
33
ETSI
00
20
82
4D
Release 10
613
ETSI TS 102 384 V10.3.0 (2015-08)
TERMINAL RESPONSE: SET UP IDLE MODE TEXT 4.8.1
Logically:
Command details
Command number:
Command type:
Command qualifier:
1
SET UP IDLE MODE TEXT
RFU
Device identities
Source device:
Destination device:
Terminal
UICC
Result
General Result:
Command performed successfully
Coding:
BER-TLV:
27.22.4.22.4.8.5
81
03
01
28
00
82
02
82
81
83
01
00
Test requirement
The Terminal shall operate in the manner defined in expected sequence 4.8.
27.22.4.22.4.9
SET UP IDLE MODE TEXT (support of Text Attribute - Strikethrough On)
27.22.4.22.4.9.1
Definition and applicability
See clause 3.2.2.
27.22.4.22.4.9.2
•
Conformance requirement
ETSI TS 102 223 [1], clauses 4.7, 5.2, 6.4.22, 6.6.22, 6.4.16, 6.6.16, 7.5.6, 6.8, 7.5, 7.5.1, 8.25, 8.70, 6.4.7 and
6.6.13.
27.22.4.22.4.9.3
Test purpose
To verify that the text passed to the Terminal is displayed as idle mode text according to the strikethrough text attribute
configuration.
27.22.4.22.4.9.4
Method of test
27.22.4.22.4.9.4.1
Initial conditions
The Terminal is connected to the UICC Simulator.
The elementary files are coded as Card Application Toolkit default.
Prior to this test the Terminal shall have been powered on and performed the PROFILE DOWNLOAD procedure.
27.22.4.22.4.9.4.2
Procedure
Expected Sequence 4.9 (SET UP IDLE MODE TEXT, display idle mode text, Text Attribute - Strikethrough On)
Step
1
2
3
4
5
6
Direction
Message/Action
Comments
Idle Mode Text.
UICC → Terminal PROACTIVE COMMAND
PENDING: SET UP IDLE MODE
TEXT 4.9.1
Terminal → UICC FETCH
UICC → Terminal PROACTIVE COMMAND: SET UP
IDLE MODE TEXT 4.9.1
Terminal → UICC TERMINAL RESPONSE: SET UP Command performed successfully.
IDLE MODE TEXT 4.9.1
UICC → Terminal PROACTIVE UICC SESSION
ENDED
Only if idle screen not already available.
USER → Terminal Select idle screen
ETSI
Release 10
Step
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26