DR6
TOUCHSCREEN REMOTE
100-240 V
50/60 Hz 18 Watts
Equipment must be connected to a
grounded mains socket-outlet. Laite on
Liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan. Apparaten
skall anslutas till jordat uttag.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Engineered, manufactured and supported
by Rane Corporation in Mukilteo, WA,
USA, using globally sourced materials.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
ATTENTION: RISQUE DE CHOCS ELECTRIQUE NE PAS OUVRIR.
WARNING: This product may contain
chemicals known to the State of
California to cause cancer, or birth
defects or other reproductive harm.
REMOTE
POWER
INJECTOR
Rane Corporation
Class 2 wiring
Shielded CAT 5e or better
Output: 24 VDC @ 550 mA
TO REMOTE
DATA OUTPUT
TO RACK
DATA INPUT
See the HAL Installation Manual for all DR instructions and warranty information.
The HAL Installation and Design Manuals, data sheets with specifications, Halogen software and help files, graphics
and CAD files, and system applications are available at rane.com/hal.
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by Rane Corporation could void the user's authority to operate the
equipment.
CAN ICES-3 (B)/NMB-3(B)
Recycle cardboard and paper.
Shielded CAT5e or better cables are required in order to comply with the FCC Rules part 15
limits for a Class B digital device.
Warning
This product may contain chemicals known to the State of California to cause cancer, or birth
defects or other reproductive harm.
21821
Cartons et papier à recycler.
DR6
TOUCHSCREEN REMOTE
General Description
The DR6 is a fully customizable touchscreen remote for the
HAL family. It supports multiple pages or tabs and any set of
levels, toggles, selectors and/or commands. Drag, drop and resize
controls any way that’s desired. Use custom background images
and logos in full-color on the 7-inch LC display.
Screw the included wall-mount bracket over U.S. or international electrical boxes, or flush mount the 3/4" thick DR6 with a
2-inch (5 cm) square hole in the wall to accommodate the cable.
The optional DS1 desk stand accessory (shown) allows the DR6
to rest or mount on a horizontal surface. The optional RB1 rack
bracket securely installs a DR6 into a 19" equipment rack.
The included midspan power injector (not PoE) connects
shielded CAT 5e (or better) cables between any HAL and the
DR6 to deliver communications and the extra power needed for
the display.
Optional, on-screen User Access logins secure management
pages from public or staff use, and a programmable ambient light
sensor automatically dims the backlight.
The Control Page Designer in Halogen allows you to create
one set of pages and use them in a web control design, DR6
display or both.
DR6 with optional
DS1 Desk Stand
See the HAL Installation Manual or the Halogen software
Help for all DR6 instructions. Information on HAL,
Halogen and peripherals is available at rane.com/hal.
DR6 with optional
RB1 Rack Bracket (3U)
DR6 Wiring
Any HAL
HAL
LAN
LINK
ETHERNET
DR6
DIGITAL REMOTES
8
7
6
5
4
REMOTE AUDIO DEVICES & DRs
3
2
1
4
3
2
1
From HAL to DR6
100 meters (325 feet) max
TO REMOTE
DATA OUTPUT
TO RACK
DATA INPUT
Shielded CAT 5e or better
data to and from the rack.
Shielded CAT 5e or better
data and power to and from the remote.
REMOTE
POWER
INJECTOR
The RPI can go anywhere in between.
RPI
Data Sheet-1
DR6
TOUCHSCREEN REMOTE
All the items on this page
are included with the DR6.
Includes (2) Torx T10 screws
to mount the DR6 to the Wall
Plate or the DS1 Desk Stand.
DR6 Touchscreen
The assembled rear view
showing the CAT 5 cable
connection is shown below.
Includes (4) #6-32x7/8" screws
to attach to a 1-, 2- or 3-gang
US electrical box, or to the
RB1 Rack Bracket.
Includes (4) #6-20x1-1/4"
drywall screws with anchors
to mount directly on a wall.
(1.55" square hole required).
DR6 Wall Plate (included with a DR6)
RPI Remote Power Injector (included with a DR6) [not a Power-over-Ethernet injector]. IEC power cable included.
Data Sheet-2
DR6
TOUCHSCREEN REMOTE
DS1 Desk Stand for DR6 (accessory)
DS1 Features
• All steel, painted white.
• Rubber bottom protects the desktop.
• Kensington security hole.
• Holes in the bottom to fasten to a desktop.
• Larger hole in bottom to thread CAT 5 cable
through the desktop.
RB1 Rack Bracket for DR6 (accessory)
RB1 Features
• All steel, painted black.
• 3U rack height.
• Mount the Wall Plate to the RB1 using the
#6-32x7/8" screws, then mount the DR6
using the Torx T10 screws.
Data Sheet-3
DR6
TOUCHSCREEN REMOTE
DR6 Specifications
Parameter
Display
...Size
...Resolution
...Color Depth
...Ambient Light Sensitivity
Touch Screen
...Size
...Type
Mounting Hardware
...Included Mounting Screws
...Included Wall Screws
...Included Electrical Box Screws
RPI Data Input Port
RPI Data Output Port
...Power
...HAL to RPI to DR6 Distance
RPI Power Requirement
Wiring
Ambient Room Temperature
Unit: Conformity
DR6 Unit: Size
...DR6 Weight
...Included Wall Plate Size
...Included RPI Power Supply Size
...RPI Power Supply Weight
...Shipping (DR6 with RPI)
DS1 Desk Stand Accessory: Size
...Weight
...Shipping (DS1)
RB1 Rack Bracket Accessory: Size
...Weight
...Shipping (RB1)
Specification
Limit
3.38" x 6"
480 x 800 pixels
16-bit
Software configurable
Conditions/Comments
8.6 x 15.5 cm
131,071 colors
Adjust the sensitivity to ambient light changes.
3.42" x 6.10"
Resistive
8.7 x 15.5 cm
#6-32x1/4" Torx T10 (qty 2)
#6-20x1-1/4" (qty 4)
#6-32x7/8" (qty 4)
To a DR Port on a HAL
To the DR6
24 VDC @ 550 mA
100 meters / 325 feet total
100 to 240 VAC
Class 2
104 °F / 40 °C
CE, FCC, CCSAUS
5.0˝H x 7.7˝W x 0.76˝D
1 lb
4.41"H x 7.7"W
1.78˝H x 6.9˝W x 2.79˝D
14.1 oz
3 lb 3 oz
4.5˝H x 7.6˝W x 4.6˝D
1 lb 1 oz
1 lb 5 oz
5.2˝H x 19˝W x .4˝D
1 lb 1 oz
1 lb 14 oz
Secures DR6 to Wall Plate or DS1 desk stand
Drywall / cement anchors included
Used to mount Wall Plate to an electrical box or RB1
RJ-45 connector
RJ-45 connector
max
max
Shielded CAT 5e cable or better (see diagram)
50/60 Hz, 18 W max
All RJ-45 connectors
Maximum external loading
12.6 x 19.6 x 1.9 cm
455 g
11.2 x 19.6 cm
4.6 x 17.6 x 7 cm
400 g
1.47 g
11.4 x 19.3 x 11.7 cm
480 g
600 g
13.2 x 48.3 x 1 cm
480 g
850 g
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5000 TEL 425-355-6000 FAX 425-347-7757 WEB rane.com
Data Sheet-4
All features & specifications subject to change without notice. 12-14
Declaration of Conformity
Standard(s) to which
conformity is declared:
Application of Council directive(s):
2001/95/EC
2012/19/EU
2004/108/EC
2006/95/EC
2011/65/EU
EN60065:2002/A1:2006/A11:2008/A2:2010/A12:2011
EN55103-1:2009
EN55103-2:2009
EN50581:2012
ENVIRONMENT E2
Serial Numbers: 900000-999999
CE mark first affixed in: 2014
Manufacturer:
Rane Corporation
10802 47th Avenue West
Mukilteo WA 98275-5000 USA
This equipment has been tested and found to be in compliance with all applicable standards and regulations applying to the
EU’s Low Voltage (LV) directive 2006/95/EC, and Electromagnetic Compatibility (EMC) directive 2004/108/EC. In order
for the customer to maintain compliance with this regulation, high quality shielded cable must be used for interconnection to
other equipment. Modification of the equipment, other than that expressly outlined by the manufacturer, is not allowed under
this directive. The user of this equipment shall accept full responsibility for compliance with the LV directive and EMC directive in the event that the equipment is modified without written consent of the manufacturer. This declaration of conformity
is issued under the sole responsibility of Rane Corporation.
Type of Equipment: Professional Audio Signal Processing
Model: DR6 and Remote Power Injector
Immunity Results:
Test Description
Results
RF Electromagnetic Fields Immunity
80 MHz -1000 MHz, 1 kHz AM, 80% depth, 3V/m
No Susceptibility
1400 MHz - 2700 MHz, 1 kHz AM, 80% depth, 3V/m
No Susceptibility
Conducted RF Disturbances Immunity
150 kHz - 80 MHz, 1 kHz AM, 80% depth, 3V rms
No Susceptibility
Magnetic Fields Immunity
50 Hz - 10 kHz, 3.0 - 0.3 A/m
No Susceptibility
Common Mode Immunity (Data Ports)
50 Hz - 10 kHz, 100 Vrms
No Susceptibility
I, the undersigned, hereby declare that the equipment specified above conforms
to the Directive(s) and Standard(s) shown above.
(Signature)
Greg Frederick
Compliance Engineer
(Full Name)
(Position)
August 22, 2014
Mukilteo WA USA
(Date)
(Place)
DR6
TOUCHSCREEN REMOTE