Installation Instructions for
Installing the Advanced Video Input
Board in a D9032 Encoder
Overview
Audience
These installation instructions apply to trained Cisco service personnel who want to
install an Advanced Video Input Board in a D9032 Encoder.
Introduction
Installation of the Advanced Video Input Board must only be performed by trained
Cisco service personnel. Contact your local Cisco sales office for further information
on how to get your D9032 Encoder(s) upgraded.
Document Version
This is the third release of these installation instructions.
In This Document
General ...................................................................................................................................... 2
AVIB Upgrade Kit ................................................................................................................ 2
Software Upgrade Kit........................................................................................................... 2
Before You Start .................................................................................................................... 3
Upgrading the Software .......................................................................................................... 4
To Upgrade the Software ..................................................................................................... 4
Removing the Top Plate .......................................................................................................... 5
Removing Modules.................................................................................................................. 6
Inserting the Modules ............................................................................................................. 9
Installing the Advanced Video Input Board ..................................................................... 9
Reinstalling the Dual Audio Module (If Present) .......................................................... 12
Installing the Advanced Video Input, SDI Option............................................................ 13
To Install the Advanced Video Input, SDI Option......................................................... 13
For Information ...................................................................................................................... 14
General
General
WARNING:
Allow only Cisco service personnel to open the unit. Otherwise, personal
injury or equipment damage may occur.
CAUTION:
The unit contains electrostatic discharge (ESD) sensitive components.
Observe the following rule:
Do not attempt to open a unit without proper precautions against
electrostatic discharge, i.e. use a wrist strap and conductive work-bench
surface. Reason: The unit may fail or be degraded
AVIB Upgrade Kit
The parts required for installing the Advanced Video Input Board are supplied in
the following kit:
Item
Kit, Advanced Video Input Board, AVIB
Part Number
4015092
Software Upgrade Kit
The Advanced Video Input Board requires a D9032 Encoder software version v02.06
or greater. This can be ordered as a software upgrade kit:
Item
D9032 Encoder, software upgrade kit
Part Number
4015939
Advanced Video Input, SDI Option
The Advanced Video Input Board has an SDI option which can be enabled by
installing a license file. The Advanced Video Input, SDI option can be ordered as an
add-on product to the Advanced Video Input Board:
Item
Advanced Video Input, SDI Option
2
Part Number
4015093
4015277 Rev C
General
Before You Start
You need the following tools and accessory:
Item
Screwdriver, PH-1
Flat bladed screwdriver
Internal hex wrench, 5 mm
Sechskant-Rohr-Steckschlüssel 13 mm aus Stahlrohr (Hex-end tube
wrench, 13 mm) Manufacturer: Hahn+Kolb part number 52174130. Can be
bought from www.mercateo.com.
4015277 Rev C
3
Upgrading the Software
Upgrading the Software
To Upgrade the Software
Important: The Advanced Video Input Board requires a software version v02.06 or
greater.
Perform the following steps to upgrade the software to version v02.06 or greater:
1.
Power up the unit and connect it to a PC via an Ethernet LAN.
2.
Enter the GUI by typing the unit’s IP address in the Internet Explorer address field.
3.
From the user interface of the D9032 Encoder click the System tab and the System
icon from the sub-pages.
4.
Store the old setting files before upgrading to a new software version.
This enables you to restore your settings if you need to downgrade
5.
Click the Upgrade button.
6.
Browse to the appl.pkg file and click Transfer.
Note: It may take several minutes to upgrade the software for all 4 modules.
Important: Due to a restriction in the MS Internet Explorer the path of the software
package file (appl.pkg) should be less than 50 characters long.
4
4015277 Rev C
Removing the Top Plate
Removing the Top Plate
Perform the following steps to remove the top plate of the D9032 Encoder:
1.
Switch off the power to the D9032 Encoder. Remove the power cord.
Dismount the Encoder from the rack.
2.
4015277 Rev C
Unscrew the 8 screws holding the top plate.
5
Removing Modules
Removing Modules
Perform the following steps to remove the modules from the unit:
1.
Note the location of the various modules in the drawing below.
Dual Audio (4006569)
SDI INPUT (4009245)
6
Composite Video (4010240)
2.
Unscrew the screws holding the SDI, Composite and Dual Audio modules.
3.
Remove the plastic washers for the SDI and Composite video modules.
4.
Unplug the coax cable from the SDI module and loosen it from the 2 clamps.
4015277 Rev C
Removing Modules
5.
Remove the SDI, Composite and Dual Audio module, if present.
Note: The audio module must be removed in order to replace the BNC cable for the
SDI input.
Insert a flat bladed screw driver in the odd shaped holes in the sides of the chassis
and carefully loosen the modules little by little.
You do this by inserting the screwdriver under the module.
Important: Only insert a few millimeters in order not to damage the components on
the boards.
Take care to lift the module equally by switching the position of the screwdriver from
one end of the module to the other.
4015277 Rev C
7
Removing Modules
6.
Unscrew the BNC from the rear panel and remove the coax cable.
This is done by cutting the cable holding the internal connector and unscrewing the
nut key using a hex-end tube wrench (13 mm).
Important: Be careful not to scratch the board with the screwdriver when unscrewing
the nut with the wrench.
8
4015277 Rev C
Inserting the Modules
Inserting the Modules
Installing the Advanced Video Input Board
Perform the following steps to install the Advanced Video Input Board in the D9032
Encoder:
1.
Note the location of the various modules, coax cable (4012556) and “Cable SAD ADH
4x3” (3989827) in the drawing below.
3989827
4012556
Dual Audio (4006569)
AVIB (4013267)
4015277 Rev C
9
Inserting the Modules
2.
Mount the BNC cable in the D-shaped hole in the rear panel.
3.
Use the hex-shaped 13 mm tube wrench and a screwdriver to tighten the nut.
Important: Be careful not to scratch the board with the screwdriver when tightening
the nut with the wrench.
10
4015277 Rev C
Inserting the Modules
4015277 Rev C
4.
Inspect the connectors on the main board for bent pins. Straighten any bent pins
before inserting the Advanced Video Input module.
5.
Position the Advanced Video Input module (4013267). Be very careful when pressing
the board into the connectors and make sure that the connectors are mating.
6.
Secure with 4 screws (3984307) Tighten to torque = 0,7 Nm
7.
Connect the coax cable (4012556) to the Advanced Video Input module and fixate
with one “CABLE SAD ADH 4X3” (3989827).
11
Inserting the Modules
Reinstalling the Dual Audio Module (If Present)
Proceed as follows to reinstall the Dual Audio Module:
12
1.
Inspect the connectors on the main board for bent pins. If there are bent pins
straighten them before inserting the Dual Audio Module.
2.
Mount the board into the connectors make sure that the connectors are mating.
Secure with 4 screws (part number 3984307).
4015277 Rev C
Installing the License File for the Advanced Video Input,
SDI Option
To Install the License File for the Advanced Video Input, SDI Option
The below procedure is only relevant if you have bought the Advanced Video Input,
SDI Option, part number 4015093.
Perform the following steps to install the license file for the Advanced Video Input,
SDI Option:
1.
Power up the unit and connect it to a PC via an Ethernet LAN.
2.
Enter the GUI by typing the unit’s IP address in the Internet Explorer address field.
3.
Insert the CD ROM from the license kit in the CD ROM drive.
4.
Click the Options License icon from the System tab in the GUI.
5.
Click the Install… button.
6.
Browse for the license file on the supplied CD ROM drive and click Open.
Loading takes approximately 10 seconds. The option is installed in your Encoder.
Check that the text in the Installation Status column changes from Not Installed to
Installed and the Status column from Disabled to Enabled.
7.
4015277 Rev C
Click Apply.
13
Installing the License File for the Advanced Video Input, SDI Option
For Information
If You Have Questions
If you have technical questions, call Cisco Services for assistance. Follow the menu
options to speak with a service engineer.
14
4015277 Rev C
Cisco Systems, Inc.
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
678 277-1120
800 722-2009
www.cisco.com
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates
in the U.S. and other countries. A listing of Cisco's trademarks can be found at
www.cisco.com/go/trademarks.
Third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (1009R)
Product and service availability are subject to change without notice.
©2006-2011, 2012 Cisco and/or its affiliates. All rights reserved.
April 2012 Printed in USA
Part Number 4015277 Rev C