105U-G Wireless Gateway Data-bus Interface and Conversion Applications

advertisement
105U-G Wireless Gateway
Data-bus Interface and Conversion
Applications
• Similar/dissimilar data-bus SCADA/ • Smart instrument interface and
DCS to PLC-PLC communications
connection (e.g., gas analyzer)
• Moving machinery PLC-PLC/HMI
• Multi I/O data concentrator/
connection/operation
repeater for large networks
• Data-bus cable replacement
Specifications
Transmitter/Receiver
Modulation
DFSK
Transmit Power
148 - 174MHz, 0.1 - 5W
220 - 235MHz, 0.1 - 5W
360 - 512MHz, 10mW - 5W
869.525MHz, 500mW
869.875MHz, 5mW
Receiver Sensitivity
150/220/400MHz: –112dBm
869MHz: –108dBm
Data Rate
150/220/400MHz: 3.6 kbps
869MHz: 19.2kbps
Line Of Sight
Range(2)
150/220/400MHz: 10mW EIRP to 2km,
500mW EIRP to 10km, 5W EIRP to 50km
869MHz: 5km (500mW), 1km (5mW)
Antenna Connector
150/220/400MHz: BNC female coaxial
(with gas discharge arrestor).
869MHz - SMA female (with gas discharge arrestor).
• Able to connect similar/dissimilar industrial protocols and vendor devices
(incorporating: Master/Slave, Slave/Slave, Master/Master networks).
Onboard D I/O(1)
Eight non voltage/FET I/O: 30Vdc/500mA
• Simple to complex, point to multi-point communications with forwarderror correction (FEC), data inte.g.,rity check (CRC) and data encryption.
Ethernet Port
10/100Mbps, RJ45 - IEEE802.3
LEDs
Link/100Mbps
Description
ELPRO wireless gateways provide the interface and communication between
industrial data-bus devices and field devices (e.g., Modbus to Profibus to
EtherNet/IP: PLC’s to SCADA/DCS etc). Connected via RS232/RS485/RJ-45,
re.g.,ister allocated data-bus values are transmitted/received by radio to and
from field and control room devices.
ELPRO 105U-G series products can multi-hop repeat up to five times,
support a variety of industrial protocols and can be combined with ELPRO
105U/505U-K and 115S series products to create I/O and data-bus networks.
Features
• 150/220/400/869MHz, 5mW-5W, DFSK(1), 3.6-19.2kbps radio
communications to 35m/56Km with multi-hop repeating.(2)
• Eight configurable digital I/O with I/O expansion via ELPRO 115S range.
• AC/DC/battery power options with UPS battery charger.
• Module diagnostics including read/write of re.g.,ister I/O, reporting of
signal strength indication (RSSI), communications logging and internal
measurement of low/normal and battery supply voltages.
Input/Output
Ethernet Port - model/protocol dependent
Note: Specifications subject to change.
1) DFSK - Digital Frequency Shift Key.
2) Actual radio distances dependent on terrain/obstacles. Country re.g.,ulations and
module dependant.
Continued on back.
©2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211
BU-SB11836
Page 1 of 3
(1)
Data Sheet # 7908
105U-G Wireless Gateway
Data-bus Interface and Conversion
Specifications
General
Serial Port
Size
5.1” x 7.3” x 2.4” (130 x 185 x 60mm)
RS232
9pin DB9 female connector
Weight
2.2lbs (1Kg)
RS485
Terminal connector (serial expansion module option: cable
<2000m)
Temperature
Data Rate
Configurable
9600 baud, 8 bits, no parity, 1 stop bit (programming)
300 - 38400, 7/8 bits, N/O/E, Parity, 1/2 Stop. Modbus/DF1
105U-G-MD1 150/220/400MHz: -30 to +60°C (-22 to 140°F)
105U-G-MD1 869MHz: -40 to +60°C (-40 to 140°F)
105U-G-ET1/PR1/PR2/DE1/M+1: -30 to +60°C (-22 to 140°F)
Humidity
105U-G-MD1: RH Non-condensing 0-99%
105 U-G-ET1/PR1/PR2/DE1/M+1: RH Non-condensing 0 - 95%
Housing
Extruded aluminum
Mounting
DIN rail mounting
Terminal strip
Removable: up to 2.5mm2 (12AWG)
EMC: FCC Part 15, AS3548, EN 301 489
Radio: EN 300 220, FCC Part 90, RSS 119, AS4295, AS4768.1,
EN 300 113
Safety: EN 60950, Class I Division 2 hazardous areas (USA/
Canada)
Protocols and Configuration
105U-G-MD1
Modbus RTU
(Master/Slave), DF1
Up to 4300 I/O points: analog and/or discrete
Modbus - RS232/485: 300 - 38400bps
DF1 (full duplex) - RS232: 300 - 38400bps
105U-G-ET1
EtherNet/IP (Level
2I/O Server)
Modbus/TCP (Class 0, 1: partially class 2 Slave)
TCP/IP functions; embedded web system (dynamic HTTP); onboard file system for downloadable web pages via FTP server; email
(SMTP)
2048 bytes input/2048 bytes output: up to 4300DI/O or
1024AI/1024AO. 10/100Mbps, RJ45 connector
Approvals
105U-G-PR1
Profibus DP Slave to
EN 50170 standard
416I/O bytes (up to 1952DI/ 1952DO or up to 122AI/ 122AO)
RS-485 optically isolated with onboard DC/DC converter
Automatic baud rate detection: 9600bps - 12Mbps
Nominal Supply
12-24Vac/9-30Vdc: over-voltage/reverse power protected
Quiescent Current
105U-G-PR2
Profibus DP Master
to EN 50170
standard
2048 bytes input/2048 bytes output: up to 4300 DI/O or
1024AI/1024AO
RS-485 optically isolated with onboard DC/DC converter
Automatic baud rate detection: 9600bps - 12Mbps
105U-G-MD1: +12V, 150mA: 24V, 90mA: add 5mA per I/O point
105U-G-ET1/PR1/PR2/DE1/M+1: +12V, 270mA: 24V, 170mA:
add 5mA per I/O point
105U-G-DE1
DeviceNet Slave
512 bytes input/512 bytes output (up to 4300DI/O or 256AI/
256AO)
Re.g.,ister size 16 bit - number of remote 905U addresses 500
RS422 optically isolated (selectable baud rate between 125, 250,
500kbps)
105U-G-M+1
Modbus+Slave
Global database transactions: routing up to six networks
2048 bytes input/2048bytes output (up to 4300DI/O or
1024AI/1024AO) RS485 optically isolated: standard baud rate
1Mbps
User Configuration
E-Series configuration utility
Power Supply
Transmission Current 450mA @ 13.8Vdc (0.5W)
600mA @ 13.8Vdc (1W)
800mA @ 13.8Vdc (2W)
1.25A @ 13.8Vdc (5W)
Battery Supply
11.5-15.0Vdc (battery supply volts internal I/O value)
Battery Charge
Circuit
Suitable for 12Vdc sealed lead acid batteries, max charge
current 2.0A (5W), 0.9A (500mW)
Note: Specifications subject to change.
1) Configurable as inputs/outputs.
LED Indication
ACTIVE (ACT)
Micro processer/ Module operational
OK
Mains/ battery power supply available
SERIAL TX & RX
Serial port transmitting; Serial port receiving
RADIO TX & RX
Radio transmitting; Radio receiving
I/O LED markers
I/O inputs and/or outputs status
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of
any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
©2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211
BU-SB11836
Page 2 of 3
Data Sheet # 7908
105U-G Wireless Gateway
Data-bus Interface and Conversion
Ordering
Accessories
To order, select product code from the table and specify country of application.
The following accessories can assist with compatibility when commissioning.
Product Code
Description
Frequency
RF Power
Product Code
Description
Data
Sheet #
Industrial Protocol - Devicenet Slave
Antennas 148 - 174MHz
105U-G-DE1-150-5W
Gateway, DeviceNet Slave
148-174MHz(2)
0.1 - 5W
105U-G-DE1-220-5W
Gateway, DeviceNet Slave
220-235MHz(2)
0.1 - 5W
105U-G-DE1-xxx -5W
Gateway, DeviceNet Slave
360-512MHz
0.5 - 5W
105U-G-DE1-xxx(1) -500M
Gateway, DeviceNet Slave
360-512MHz(2)
10 - 500mW
UDP200-C
Dipole Antenna: N-type Female, 0dBi gain
7939
UDP200-3
Dipole Antenna: BNC Male, 0dBi gain, 9’ (3m) Coaxial cable
7939
UDP400-C
Dipole Antenna: BNC Male, 0dBi gain, 9’ (3m) Coaxial cable
7940
Dipole Antenna: N-type Female, 0dBi gain, 9’ (3m) Coaxial cable
7940
(1)
(2)
105U-G-DE1-868-500M
Gateway, DeviceNet Slave
869.525MHz
500mW
105U-G-DE1-868-5M
Gateway, DeviceNet Slave
869.875MHz
5mW
Industrial Protocol - Ethernet/IP, Modbus TCP
UDP150-5
Dipole Antenna: BNC Male, 0dBi gain, 16’ (5m) Coaxial cable
7939
Antennas 220 - 235MHz
Antennas 360 - 512MHz
(2)
0.1 - 5W
UDP400-3
0.1 - 5W
YU-3/400
Yagi Antenna: 3 element, N-type, 10dBi gain
7940
Yagi Antenna: 6 element, N-type, 9dBi gain
7940
105U-G-ET1-150-5W
Gateway, Ethernet
148-174MHz
105U-G-ET1-220-5W
Gateway, Ethernet
220-235MHz(2)
105U-G-ET1-xxx -5W
Gateway, Ethernet
360-512MHz
0.5 - 5W
YU-6/400
105U-G-ET1-xxx(1)-500M
Gateway, Ethernet
360-512MHz(2)
10 - 500mW
YU-16/400
Yagi Antenna - 16 element, N-type, 15dBi gain
7940
500mW
BU-3/400
Collinear Antenna: N-type Female, 5dBi gain
7940
5mW
BU-6/400
Collinear Antenna: N-type Female, 8dBi gain
7940
(2)
0.1 - 5W
CFD890EL
Dipole Antenna: SMA, 2dBi, 16’ (5m) RG58, bracket
7942
0.1 - 5W
SG900EL
Collinear Antenna: N-type Female, 5dBi gain
7942
Collinear Antenna: N-type Female, 8dBi gain
7942
(1)
105U-G-ET1-868-500M
105U-G-ET1-868-5M
Gateway, Ethernet
Gateway, Ethernet
(2)
869.525MHz
869.875MHz
Antennas 869MHz
Industrial Protocol - Modbus Plus Slave
105U-G-M+1-150-5W
Gateway, Modbus Plus Slave
148-174MHz
105U-G-M+1-220-5W
Gateway, Modbus Plus Slave
220-235MHz(2)
105U-G-M+1-xxx -5W
Gateway, Modbus Plus Slave
360-512MHz
0.5 - 5W
SG900-6
105U-G-M+1-xxx(1)-500M
Gateway, Modbus Plus Slave
360-512MHz(2)
10 - 500mW
DG800-5
Whip Antenna: SMA Male, -2dBi gain, 16’ (5m) RG174, bracket
7942
500mW
YU6/870
Yagi Antenna: 6 element, N-type, 9dBi gain
7942
(1)
105U-G-M+1-868-500M
105U-G-M+1-868-5M
Gateway, Modbus Plus Slave
Gateway, Modbus Plus Slave
(2)
869.525MHz
869.875MHz
Cables
5mW
Industrial Protocol - Modbus RTU/DF1
CC3/10/20-SMA
Coaxial Cable Kit - 10’ (3m)/33’ (10m)/66’ (20m), N-type to SMA
7932
Coaxial Cable Kit - 33’ (10m)/66’ (20m), N-type to BNC
7932
105U-G-MD1-150-5W
Gateway, Modbus/DF1
148-174MHz(2) 0.1 - 5W
CC10/20-BNC
105U-G-MD1-220-5W
Gateway, Modbus/DF1
220-235MHz(2)
0.1 - 5W
CCTAIL-SMA-F/M
Coaxial Cable Tail - 2’ (600mm), SMA to N-type Female/Male
7932
105U-G-MD1-xxx -5W
Gateway, Modbus/DF1
360-512MHz
0.5 - 5W
CCTAIL-BNC-M
Coaxial Cable Tail - 2’ (600mm), BNC to N-type male
7932
105U-G-MD1-xxx(1)-500M
Gateway, Modbus/DF1
360-512MHz(2)
10 - 500mW
SER-DB9
Serial RS232 Cable - DB9 male to DB9 female straight through
7932
(1)
(2)
105U-G-MD1-868-500M
Gateway, Modbus/DF1
869.525MHz
500mW
105U-G-MD1-868-5M
Gateway, Modbus/DF1
869.875MHz
5mW
Industrial Protocol - Profibus Master/Slave
105U-G-PRx(3)-150-5W
Gateway, Profibus
148-174MHz(2) 0.1 - 5W
105U-G-PRx(3)-220-5W
Gateway, Profibus
220-235MHz(2)
0.1 - 5W
105U-G-PRx(3)-xxx(1)-5W Gateway, Profibus
360-512MHz(2)
0.5 - 5W
105U-G-PRx -xxx -500M
Gateway, Profibus
360-512MHz
10 - 500mW
105U-G-PRx(3)-868-500M
Gateway, Profibus
869.525MHz
500mW
105U-G-PRx(3)-868-5M
Gateway, Profibus
869.875MHz
5mW
(3)
(1)
(2)
Note: Available RF power and frequency may vary depending on country of application.
1) Represents frequency band (370, 390, 410, 430, 440, 460, 480, 500).
2) Ordering code requires the frequency selected.
3) 1 - Profibus Master or 2 - Profibus Slave.
Surge Diverters
CSD-SMA-2500
SMA Surge Diverter for use with CC10, CC20 - SMA
7936
CSD-N-6000
Coaxial Surge Divertor, Bulkhead N Female to N Female
7936
MA15/D/1/SI
Power Supply Surge Diverter, 110Vac/15A
7936
IOP32/IOP32D
Signal Surge Diverter, 2 wire/4 wire
7936
Power Supplies
PS-DINAC-12DC
DIN Rail Power Supply, 100 - 250Vac, 12Vdc/2.5A
7935
PS-DINAC-24DC
DIN Rail Power Supply, 100 - 250Vac, 24Vdc/2A
7935
Mounting Brackets
BR-YAGI-KIT
Mounting Bracket Kit for Yagi Antenna
7933
BR-COL-KIT
Mounting Bracket Kit for Collinear Antenna
7933
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of
any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
©2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211
BU-SB11836
Page 3 of 3
Data Sheet # 7908
Download