1.
V90292 REV A
ACCURUS SQUARE TRIM METAL HALLIDE
ACT971 BASED SERIES
Page 1 of 2
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
Fixture Mounting:
Butterfly Mounting (Commercial):
1.
Fixture comes equipped with Universal Butterfly Mounting brackets and can take common 1 inch or 1-1/2 inch Black
Iron or Galvanized Mounting Channels (Supplied By Others).
2.
Position Fixture so the Mounting Channels lie on top of ceiling runners.
Fasten Mounting Channels securely to ceiling runners.
3.
4.
Secure Mounting channels to Universal Butterfly Mounting
Brackets with wire tire downs.
5. Adjust elevation of Fixture so Mudding Ring Edge will be flush with surface of finished Ceiling by loosening two (2) 1/4 inch
Hex Screws on both Universal Mounting Brackets. See Fig. 1.
6. Tighten two (2) 1/4 inch Hex Screws on both Universal
Butterfly Mounting Brackets to secure Fixture. See Fig. 1.
Hanger Bar Mounting (Residential):
7. Adjustable hanger bars are preassembled with mounting bracket and provided with fixture.The preassembled hanger bars must attached to the fixture prior to installation.Align with two screws on end of fixture and tighten .Hanger bars are installed in Fig.1.
Fixture Housing
Cover
Mounting Channel
(Supply by Others)
8. Hanger bars can be used with grid ceilings having T bars and joist installations of wood.Adjustable hanger bars are for use in installations with spacing from 12" to 24", while maintaining minimum 1/2" spacing around fixture
Grid Ceiling Installation (Figure 2):
Step 1 Extend bar hangers between the T bars and slide the slots in the mounting tabs over the T-bars.
Step 2 Adjust housing platform position by sliding back and forth on bar hangers to desired position. Housing may be locked in the position by tightening bar hanger locking screws on housing platform.See Detail 3A.
Joist Installation (Figure 3):
Step 1 Extend bar hangers to fit between joist and position mounting tab locater lip tight to bottom of joist or framing member. Bar hangers should be level with bottom of joist or framing member.
Step 2 Attach bar hangers to joist or framing member using appropriate hardware for material.
Step 3 Adjust housing platform position by sliding back and forth on bar hangers to desired position. Housing may be locked into position.See Detail 3B.Nail Supplied in hanger bars will be suitable.
Bracket
Optional
"T"
Screw
1/4" Hex Screw
Universal Butterfly
Mounting Bracket
Trim Mechanism
Figure 1
Hanger Bars
Mudding Ring
Safety Cable
Figure 2
10"
Score Lines
V90292 REV A
ACCURUS SQUARE TRIM METAL HALLIDE
ACT971 BASED SERIES
Page 2 of 2
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
9. Install Ceiling drywall up to Adjustable Aperature Ring on Fixture
See Fig. 4.
10. Position Adjustable Aperature Ring to be in plane with Ceiling by sliding up or down.See Fig.4
11. Apply caulking or mudding compound around perimeter edge of
Adjustable Aperature Ring and drywall cutout.
12. Connect Safety Cable attached to Trim to Fixture by inserting
Safety Cable through opening in Fixture and inserting Snap Hook
(See Fig. 1) on end of Safety Cable into hole in Bracket attached to inside of fixture.Install trim mechanism into fixture by pressing firmly to engage Retainer Spring Clips . See Fig.4.
Lock Knob
Adjustable Aperture Ring
Rotational Adjustment Ring
Fixture
Ceiling
Caulk
Adjustable Aperture Ring
Retainer Clip
Trim Mechanism
DETAIL A
SCALE 1 : 4
DETAIL B
SCALE 2 : 1