Installation Instructions - page 1 of 2 ELEMENT / LOFT MICRO CONTINUOUS/ INDIVIDUAL WALL MOUNT LUMINAIRE WARNINGS 1). WARNING! – Risk of Fire/Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 2). WARNING! – Risk of Fire/Electric Shock. If not qualified, consult an electrician. 3). WARNING! – Risk of Fire/Electric Shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when drilling for installation of reflector kit hardware. Check for enclosed wiring and components. 4). WARNING! – Avoid contact with LED modules. NOTES 1). NOTE! – This product must be installed in accordance with local/ national electrical codes. 2). NOTE! – Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components. 3). NOTE! – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects. 4). NOTE! – Disconnect all power before proceeding. B A1 Distance is stud to stud Additional Stud A Mounting Plate B A Distance is stud to stud Alignment Spacer J-Box (By others) Mounting Bracket For 1st fixture or individual mounting Alignment Spacer 2. Install second mounting bracket to structure. Bracket faces opposite direction of first installed bracket. Distance from bracket stud to bracket stud is 44 3/4”. Ensure bracket is level with first installed bracket. Secure alignment plate and loosely secure nut. J-Box (By Others) Mounting Bracket Fasteners 2X (By Others) 1. After installing additional structure and securing J-box at appropriate mounting height, secure mounting bracket to stud. Feed power wires through bracket. Insert alignment plate into mounting bracket and loosely secure nut. Alignment Plate Corelite 4675 Holly St, Denver CO 80216 Ph. (303) 393-1522 Fax (303) 393-1477 ADE111691 rev A Installation Instructions - page 2 of 2 ELEMENT / LOFT MICRO CONTINUOUS/ INDIVIDUAL WALL MOUNT LUMINAIRE WARNINGS 1). WARNING! – Risk of Fire/Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing. 2). WARNING! – Risk of Fire/Electric Shock. If not qualified, consult an electrician. 3). WARNING! – Risk of Fire/Electric Shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when drilling for installation of reflector kit hardware. Check for enclosed wiring and components. 4). WARNING! – Avoid contact with LED modules. NOTES 1). NOTE! – This product must be installed in accordance with local/ national electrical codes. 2). NOTE! – Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components. 3). NOTE! – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects. 4). NOTE! – Disconnect all power before proceeding. 3. On power side, remove both knock-outs on back of fixture housing. Snap bushing into knockout and feed wires into fixture. Fixture can fit over nut and hang until final postioning. 4. On opposite side of fixture, slide fixture over nut on mounting plate and tighten around aligner plate as show. View from back Knockout for mounting stud Aligner Plate Slide fixture over nut Knockout for power feed with bushing 5. Using supplied push nuts, match and connect appropriate wires. Ensure all connections are properly matched and push connections into fixture. 6. At fixture ends, break aligner plate at relief cuts and carefully insert into fixture. Tighten nut and secure fixture to mounting plate. Use pliers and gloves for safety. 7. For continuous fixture joints, make wire connections and slide joining fixture onto tab end of aligner plate. Secure with #10-32 screw and nut. 8. Secure endcaps to both sides of fixture housing. One nut required at top, bottom stud is for alignment only. Corelite 4675 Holly St, Denver CO 80216 Ph. (303) 393-1522 Fax (303) 393-1477 ADE111691 rev A