Fastening Anchors Accessories
Diamond Washer
Carriage
Bolt **
Part Number Includes
(1) Diamond Washer
Diamond
Washer
Order Separately
(1) 5/16”-18 Carriage Bolt **
(1) 5/16” Flat Washer
(1) 5/16”-18 Hex Nut
Field drilling is required.
Flat
Washer
Finish: G-90 mill galvanized
Also available in 304 stainless steel
Hex Nut
Diamond Washer
** Plank carriage bolt lengths = Side Channel Height + 1”
Walkway carriage bolt = 5/16”-18 x 2”
UPC Number
Catalog Number
Wt./Ea.
66251626610
12262
0.03
Assembly
1. Align GRIP STRUT planks on I-Beam or other
anchoring cross-member.
2. Mark the I-Beam for drilling purposes under a slot
near the end of GRIP STRUT plank. Drill a pilot hole.
3. Remove GRIP STRUT plank and drill a finish hole.
4. Replace GRIP STRUT plank. Align diamond washer
over the drilled hole. Run the carriage bolt through
the diamond washer and I-Beam. Tighten the
washer and nut until secure.
5. Test for movement or slippage. If GRIP STRUT
planks are not secure, check fastening system for
loose or missing parts. Repeat steps 1 thru 4.
Note: Do not walk on GRIP STURT planks if
they are not secure. Serious injury could result.
Welding
A common method of fastening safety grating is
welding. It is recommended that all B-Line Safety
Grating products be fillet welded per AWS D1.3.
For more information, consult Technical Services.
20
Heavy Duty GRIP STRUT
Fastening Anchor Accessories
Anchor Plate
J-Bolts
Finish: G-90
mill galvanized
Anchor
Plate
Also available in 304
stainless steel
Flat
Washers
Hex Nuts
No field drilling is required.
Part Number Includes
(1) Anchor Plate
(2) 3/8”-16 J-Bolts
(2) 3/8” Flat Washer
(2) 3/8”-16 Hex Nut
Anchor Plate Assemblies *
UPC Number
Catalog Number
Grating Height
66251634139
ACA15
ACA20
ACA25
ACA30
11/2”
2”
21/2”
3”
66251634141
66251634142
66251634144
Assembly
1. Align two (2) GRIP STRUT planks side-by-side on
I-Beam or other anchoring cross-member.
2. Place J-bolts in GRIP STRUT openings opposite
each other. Make sure you choose the openings
nearest to the inner edge of the plank .
3. Slide ACA anchor plate up J-bolts until snug. Make
sure the inside edge of the ACA anchor plate is as
close as possible to the center of the cross member.
4. Tighten nuts until planks are secured.
5. Test for movement or slippage. If GRIP STRUT
planks are not secure, check fastening system for
loose or missing parts. Repeat steps 1 thru 4.
Note: Do not walk on GRIP STRUT planks if
they are not secure. Serious injury could result.
Welding
A common method of fastening safety grating is
welding. It is recommended that all B-Line Safety
Grating products be fillet welded per AWS D1.3.
For more information, consult Technical Services.
Heavy Duty GRIP STRUT
21
J-Bolt Size
Wt./Ea.
/8”-16 x 11/2”
3
/8”-16 x 2”
3
/8”-16 x 21/2”
3
/8”-16 x 3”
0.80
0.80
0.80
0.90
3
Walkway Accessories
Walkway Splice Plate (30” Long) Kit
Part Number Includes
(2) Splice Plates
(32) /2”-13 x 11/4”Hex Bolts
(32) 1/2”-13 Hex Nuts
(32) 1/2” Washers
1
Walkway Splice Plate Kit
Walkway splice plates provide continuity
when multiple lengths of GRIP STRUT™
walkway are desired. Connections are
reinforced with the addition of splice plates
attached to side channels.
UPC Number
Catalog Number
Wt./Ea.
66251642714
SP-10DU-30
18.1
30”
17/8”
33/4” C to C
41/2”
7
1 /8”
Splice plates are formed from 12 gauge
mill-galvanized steel, prepunched and
supplied with hardware shown above.
3
/4”
Torque to 40 ft.-lbs.
22
GRIP STRUT
Walkway Accessories
Walkway Splice Plate (7” Long) Kit
Part Number Includes
(2) Splice Plates - 4” x 7”
(16) 7/16”-14 x 11/4”Hex Bolts
(16) 7/16”-14 Hex Nuts
(16) 7/16” Washers
Walkway Splice Plate Kit
Kit joins continuous sections together in
a run only over supports.
Note: Contact factory for information on
pre-punched holes in walkway grating.
Splice plates are formed from 10 gauge
mill-galvanized steel, prepunched and
supplied with hardware shown above.
Torque to 55 ft.-lbs. (minimum)
Heavy Duty GRIP STRUT
23
UPC Number
Catalog Number
Wt./Ea.
66251642716
SP-10DU-7
4.1