Quadcast LED
Occupancy Sensor and
Bird Guard
TM
INSTALLATION INSTRUCTIONS
Sheet 1 of 3
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
SAFETY: This fixture must be wired in accordance with the National Electrical Code
and applicable local codes and ordinances. Proper grounding is required to insure
personal safety. Carefully observe grounding procedure under installation section.
WARNING: Make certain power is OFF before starting installation or attempting any
maintenance. Risk of fire/electric shock. If not qualified, consult an electrician.
7/27/2012
IMI-776
• RISK OF ELECTRIC SHOCK—Disconnect power at fuse or circuit breaker before
installing or servicing.
• RISK OF BURN—Disconnect power and allow fixture to cool before servicing.
• RISK OF PERSONAL INJURY—Fixture may become damaged and/or unstable if
not installed properly. Tighten all fixture components to their recommended torque
values.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
TOOLS REQUIRED:
Electrical wiring tools, Phillips screwdriver, 1-1/8" metal drill bit or sheet metal
punch, wire stripper. Occupancy sensor installation (FIG. 4).
Occupancy Sensor
Location Mark
1. U
nscrew door mounting screws with Phillips screwdriver.
CAUTION: DOOR WILL HINGE DOWN UPON REMOVAL OF SCREWS.
SUPPORT DOOR WHILE REMOVING SCREWS.
(2) Door
Hinge Screws
(2) Door
Mounting
Screws
2. Unscrew ground wire nut and disconnect grounding conductor from door.
3. U
nscrew door hinge screws and remove door. For Steps 4-9 place door on a soft
surface.
CAUTION: ENSURE THE PAINT FINISH IS NOT SCRATCHED OR CHIPPED.
4. U
sing a 1-1/8" metal hole saw or equivalent sheet metal punch, drill/punch a
1-1/8" diameter hole in the door at the indented occupancy sensor location mark
on the door (FIG. 1).
5. R
emove lens and tightening ring from occupancy sensor.
6. Insert the threaded sensor collar through the hole from inside the fixture. Sensor
gasket should be inside of fixture (FIG. 2).
7. S ecure sensor to housing using tightening ring. Tighten to snug fit (FIG. 3).
8. R
emove sticker on sensor face and screw lens to sensor with snug fit.
Do not over tighten lens as threads will strip.
9. R
eattach door by screwing in the two door hinge screws, tighten to
15 inch-pounds.
10. R
econnect the green grounding conductor and tighten nut to 10 inch-pounds.
Refer to FIG. 4 page 3 for occupancy sensor wiring diagram
• Locate the line (Black) and neutral (White) conductors on the input side of the
driver. Cut the white and black conductor 3" from the driver. Strip insulation on
exposed ends 3/8" in length.
• Connect the sensor load conductor (RED) to the driver input black conductor
using the lever-lock connector supplied with occupancy sensor.
• Connect the sensor neutral conductor (white) to the driver input neutral and
AC input neutral conductors using the lever-lock connector supplied with
occupancy sensor.
• Connect the sensor line conductor (Black) to the AC input black conductor using
the lever-lock connector supplied with occupancy sensor.
11. L ift door to closing position and secure with two door mounting screws.
Tighten screws to 15 inch-pounds to seal fixture. ALL WIRING AND ELECTRICAL
CONNECTIONS MUST REMAIN INSIDE ENCLOSURE. ENSURE WIRING IS SECURED
WITHIN ENCLOSURE WHILE CLOSING DOOR.
FIG. 1 Bottom of Fixture
FIG. 2
Occupancy
Sensor Lens
Sensor Gasket
Occupancy
Sensor
Tightening
Ring
FIG. 3
Door
Occupancy
Sensor
Align sensor
as shown on
inside of door
Inside of
Door
—continued
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact
your nearest representative. NOTE: Specifications and dimensions subject to change without notice.
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
ADH121391
Quadcast LED
Occupancy Sensor and
Bird Guard
TM
INSTALLATION INSTRUCTIONS
Sheet 2 of 3
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
7/27/2012
IMI-776
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
DESCRIPTION AND OPERATION
The occupancy sensor has an integral photocontrol that turns lighting ON and OFF
based on occupancy and ambient light levels.
2. M
ove out of the sensor’s view. Lights turn OFF after 30 seconds.
3. M
ove into the controlled area. The red LED in the sensor lens should illuminate
and the lights should turn ON.
The sensors use passive infrared (PIR) sensing technology that reacts to
changes in infrared energy (moving body heat) within the coverage area.
Once the space is vacant and the time delay elapses (adjustable from
30 seconds to 30 minutes), lights will turn OFF.
TEST AND ADJUST LIGHT LEVEL PHOTOCONTROL SENSOR AND TIME DELAY
1. R
emove the lens assembly and adjust the light level and the time delay to
minimum. Put the lens assembly back onto the sensor. Leave the controlled
area and let the sensor time out so lights are OFF.
2. E nter the controlled area and lights should remain OFF.
3. M
ake sure your body does not cast a shadow on the sensor. Turn the light level
trimpot clockwise in small increments. After each adjustment, put the lens back
on the sensor then move about the controlled area. Wait 5-10 seconds to see if
the lights turn ON.
4. C
ontinue this procedure until the lights turn ON. At this setting the lights will
not turn ON with occupancy if the light level is above the current level.
5. S et the time delay to the desired
20 min.
15 min.
setting. The time delay can be set from
25 min.
30 seconds (fully counterclockwise) to
10 min.
30 minutes (fully clockwise).
IMPORTANT, THERE IS AN INITIAL WARM-UP PERIOD:
It may take up to a minute before the lights turn ON due to a sensor
warm-up period required during initial power-up. This occurs during
installation or after a lengthy power failure only.
WARNING
DO NOT OVERTURN TRIMPOT WHEN ADJUSTING THE SENSOR.
DO NOT TOUCH THE SQUARE INFRARED DETECTOR
UNDER THE LENS ASSEMBLY.
LIGHT LEVEL FEATURE
The Light Level photocontrol feature holds
OFF and turns OFF lights when the space is
occupied and adequate ambient light exists.
When the light level drops below the set
level it will turn the lights ON when the
space is occupied. The factory setting is
for maximum, meaning that even bright
ambient light will not cause the sensor to
hold the lights OFF if it detects occupancy
in the controlled area.
5 min.
TROUBLESHOOTING
Factory Settings
Light Level
Maximum
(light level
should not
affect load
operation*)
30 min.
30 sec.
Time
Delay
15
minutes
SENSOR ADJUSTMENT
The Light Level and Time Delay adjustment trimpots are located under the lens
assembly. The trimpots are accessed easily after the sensor is mounted in the
fixture. Gently unscrew the lens assembly. Do not remove the thumbscrew collar;
it holds the sensor in place on the fixture. Identify each trimpot. Set the light level
when the controlled light would normally be turned OFF due to the presence of
sufficient daylight or other electric light. [If this feature is not needed, leave the
light level at maximum (fully clockwise)].
* A t the maximum setting, the light level entering the photosensor must exceed
120 Fc, which only happens in rare applications or when the lens is removed.
TEST OCCUPANCY SENSOR (OPTIONAL)
1. S et Light Level to maximum (fully clockwise, factory setting) and Time Delay to
minimum (fully counterclockwise). Put the lens assembly back onto the sensor.
LIGHTS WILL NOT TURN ON:
• LED does not flash:
- Check all wire connections and verify the ground wire is tightly secured.
• LED does flash:
- Check all wire connections and verify the load wire is tightly secured.
- Check light level photocontrol setting. Cover the sensor lens to simulate
darkness in the room. If the lights come ON, the light level needs to be
adjusted. If set for minimum, more than 10 Fc of ambient light will cause
the lights to be held OFF. See Sensor Adjustment section for instructions.
LIGHTS WILL NOT TURN OFF:
The time delay can be set from a minimum of 30 seconds (fully counter-clockwise) to a maximum of 30 minutes (fully clockwise). Ensure that the time delay is
set to the desired delay and that there is no movement within the sensor’s view
for that time period.
• To quickly test the unit for proper operation, turn the time delay to minimum and
move out of the sensor’s view. Lights should turn OFF after 30 seconds.
OPERATION DURING POWER-UP
During the sensor warm-up period, which can last up to a minute after initial
power-up (or after a lengthy power outage), the load can be either ON or OFF,
depending on the status of the relay before the sensor was powered down.
After warm-up, the sensor will open or close the relay to correspond to the
occupancy status of the room.
—continued
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact
your nearest representative. NOTE: Specifications and dimensions subject to change without notice.
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
ADH121391
Quadcast LED
Occupancy Sensor and
Bird Guard
TM
INSTALLATION INSTRUCTIONS
Sheet 3 of 3
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
7/27/2012
IMI-776
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
BIRD GUARD INSTALLATION (FIG 5):
Conduit
NOTE: Bird Guard requires minimum 7" length of pendant pipe (Supplied by others). Bird guard is suitable for use with 1-gang, 2-gang, and 4" round UL wet location
listed junction boxes. Install bird guard after fixture installation.
FIG. 5
1. Remove the bird guard screw.
2. Gently open bird guard and slide around conduit.
3. Align and insert metal tabs on bird guard with slots in housing.
4. Reinstall the bird guard screw to snug fit.
5. Bend tabs on bird guard to secure to housing.
Screw
Housing Slots
Bird Guard Tabs
WIRING DIAGRAM
FIG. 4
Factory Wired
AC Input to Driver
Line (Black)
LED
Driver
DC
OUTPUT
Neutral (White)
AC
INPUT
Quadcast without
Occupancy Sensor
Red
Black
Factory Wired
Driver to LEDs
Factory Wired
AC Input to Driver
Neutral
(White)
Neutral
(White)
Line (Black)
Occupancy
Sensor
Line (Black)
AC
INPUT
Line (Black)
Neutral (White)
LED
Driver
DC
OUTPUT
Neutral
(White)
Quadcast with
Occupancy Sensor
Red
Black
Factory Wired
Driver to LEDs
Line (Black)
Load (Red)
Load (Red)
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact
your nearest representative. NOTE: Specifications and dimensions subject to change without notice.
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
ADH121391