IF 1403 NFL FLUORESCENT LIGHTING FIXTURES APPLICATION

advertisement
IF 1403
NFL FLUORESCENT LIGHTING FIXTURES
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
APPLICATION
NFL Fluorescent lighting fixtures suitable for use in Wet
Locations, NEMA 4X. They are also suitable for use where
cleanliness and sanitation are prime factors.
NFL Fluorescent lighting fixtures are supplied with a choice of
voltages and wattages. The 2 ft. fixture is available in 40 watts at
120, 277, or 347 volts, 60 Hz. The 4 ft. units are offered in 32 &
40 watts at 120, 277, or 347 volts, 60 Hz. and 220-240, 50/60 Hz.
NFL Fluorescent lighting fixtures are suitable for operation in a
40˚C ambient temperature.
INSTALLATION
that comply with the National Electrical Code or the
Canadian Electrical code and applicable local codes.
Note: NFL Fluorescent lighting fixtures must be installed,
inspected, and maintained by qualified and competent
personnel.
! CAUTION
• To avoid cycling, do not exceed an ambient temperature
of 40˚C.
• To avoid light failure, proper field wiring must be used.
! WARNING
• To avoid electrical shocks, be certain that power is OFF
before and during installation or before attempting any
maintenance.
• To avoid electrical shocks, fixture must be installed on
grounded wiring system.
1.
Rotate the mounting brackets into mounting position.
2.
Mount fixture - chain or ceiling in its support position and
attach to wiring system* (see illustration below).
*
Two (2) 1/2" Myers conduit hubs are supplied for dead end
or through feed wiring.
3.
Open lens assembly by releasing latches on both sides
4.
Remove combination reflector/cover by removing fasteners
(clips and screws).
5.
Connect fixture leads to incoming conductors using methods
! CAUTION
To maintain wet locations, NEMA 4X suitability:
• Secure all latches
• In dead end applications, also close unused end
opening with a Myers hub and 1/2” pipe plug (furnished)
6.
Replace reflector/cover and refasten using clips and/or
screws.
7.
Close lens assembly and secure all latches.
LAMPS FOR USE IN NFL LIGHT FIXTURES
GE
NFL2140
NFL4232
NFL4240
(40 watt T5 Compact)
(32 watt T8)
(34 watt T12)
High lumen Biax™
F40/30BX/SPX35/RS
(3150 lumens)
Trimline T8™
F32T8/SP35
(2850 lumens)
Watt-Miser®
F40CW/RS/WM
(2650 lumens)
F40SPX35/RS/WM
(2850 lumens)
Osram
Sylvania
Dulux® L high lumen
FT40DL/835/RS
(3150 lumens)
Octron® "700" Series
FO32/735
(2800 lumens)
F40/D35/SS
(2800 lumens)
Philips
PL Long
PL-L 40W/35/RS
(3300 lumens)
TL70 Rapid Start
F32T8/TL735
(2800 lumens)
Econ-o-watt®
F40CW/RS/EW
(2650 lumens)
F40SPEC35/RS/EW/ALTO
(2800 lumens)
Note: Higher lumen 32 watt T8 and 34 watt T12 lamps are available.
Consult lamp manufacturers.
GREEN GROUND
SCREW
GREEN GROUND
SCREW
2 FOOT ASSEMBLY
Supersaver®
F40/CW/SS
(2650 lumens)
4 FOOT ASSEMBLY
LAMP INSTALLATION/REPLACEMENT
1.
Open lens assembly by releasing latches on both sides.
2.
Install lamps. Use only correct lamps as specified on fixture
nameplate.
3.
Close lens assembly and secure all latches.
3.
Mechanically check to make sure that all parts of the fixture
are properly assembled and tight.
4.
Clean the lens assembly with a clean, damp, soft cloth. If
this is not sufficient, use a mild soap. Do not use an
abrasive, strong alkaline or acid cleaner. Damage to the
lens/housing assembly may result.
REPLACEMENT PARTS
MAINTENANCE
! WARNING
To avoid dangerous electrical shocks, always disconnect
power source before opening fixture for inspection or
service.
1.
2.
Frequent inspections should be made. A schedule for
maintenance checks should be deter mined by the
environment and frequency of use. It is recommended that
inspections should be performed at least once a year.
NFL lighting fixtures are designed to provide years of reliable
lighting performance. However, should the need for replacement
parts arise, they are available through your Crouse-Hinds
Distributor. Assistance may also be obtained through your
Crouse-Hinds Sales Representative or the Crouse-Hinds
Customer Service Department, P.O. Box 4999, Syracuse, New
York, 13221, Phone (315) 477-5531.
Latches ..............0305406
Lens
(2 ft.)......0305418
(4 ft.)......0305405
Visually check for damaged par ts and proper lamp
operation.
WIRING DIAGRAMS
For (1) 40W Biax Lamp
Using a Two Lamp Ballast
For (2) 32W or 40W Lamps
Using a Two Lamp Rapid Start Ballast
For (2) 32W or 40W Lamps Using a Two Lamp Instant Start Ballast
All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or
completeness thereof are not guaranteed. In accordance with Crouse-Hinds "Terms and Conditions of Sale", and since conditions of use are outside our control,
the purchaser should determine the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith.
Cooper Industries Inc.
Crouse-Hinds Division
PO Box 4999, Syracuse, New York 13221 • U.S.A.
Copyright© 1999, Cooper Industries, Inc.
IF 1403
Revision 4
Revised 8/99
Supercedes 5/99
Download