Room Controller Wallstation
Custom Configuration
Order Form
1—Select your color:
White (W)
Ivory (V)
(choose only one)
Gray (G)
Sales Order #: ___________________________________ _ Line #: _________________________
3—Select your desired engraving: 2—Select your button configuration:
(choose only one wallstation per form)
(choose only one, small or large button)
Choose a button address from the Standard Toggle, Standard Presets or Programmable Scenes selection list (found on
the back) for each button location.
First Letters Capitalized, Arial Font,
11 characters, 11pt font size (default)
Enter the button address on the line for the desired button. Button addresses will be factory loaded and the
wallstation will perform the default behavior shown on the back of this sheet when connected to the Room Controller.
Sample 1: Small Button (from 4 to 6 buttons)
Limited to (1) line of engraving per button
Programmable Scene button behavior can be field modified using the Personal Remote (HHPR-RC) and a connected
daylight sensor (DSRC-FMOIR).
Sample Text
PDR-RC-4TSB-*
PDR-RC-1TLB-*
PDR-RC-5TSB-*
PDR-RC-2TLB-*
Sample 2: Large Button (3 button maximum)
Limited to (2) lines of engraving per button
Sample Text
Blank
Sample Text
On 2 Lines
Check the applicable box(es) on the left for blank button(s).
Button 1
Blank
Button 2
PDR-RC-6TSB-*
PDR-RC-3TLB-*
Blank
Button 3
Blank
Button 4*
Blank
Button 5 *
Example:
PDR-RC-2TLB-*
16
8
This configuration provides an All ON / All OFF
wallstation.
Button 6*
Blank buttons are not provided.
Room Controller Wallstations will be delivered:
• Pre-programmed
• Matching color wall plates
Please print your form then email to:
ControlsCustomerService@Eaton.com or
fax to 800-954-7016.
Blank
* Buttons 4, 5 & 6 only apply when using a small button arrangement.
•
•
•
Allow 4-6 weeks for delivery from PO confirmation.
Confirmation subject to approval.
All wallstations ordered with custom text are
non-returnable.
Contact Information
Project name: ________________________________ Room: _________________________
Control Address: ______________________________________________________________
P.O. #:_________________________________________ Page:__________ Quantity:________
ACC141044
GG Order #: ______________________________ GG Project #: ________________________
Standard Toggle Buttons
Button
Address
Default Behavior
1st Press
Default Behavior
2nd Press
Control Type
1
Load 1 (Yellow) ON
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Solatube Open (RC3DE only)
Emergency Relay ON (RC3DE only)
Load 1 (Yellow) OFF
Receptacle Switchpack no action
Alternate Voltage Switchpack OFF
Solatube Close (RC3DE only)
Emergency Relay OFF (RC3DE only)
Toggle
2
“Load 2 (Red) ON
Receptacle Switchpack ON”
“Load 2 (Red) OFF
Receptacle Switchpack no action”
Toggle
3
Load 3 (Purple) ON
Load 3 (Purple) OFF
Toggle
5*
Disables Occupancy sensor for 60 minutes
Re-enables Occupancy sensor
Toggle
11
"Load 3 (Purple) ON
Receptacle Switchpack ON"
"Load 3 (Purple) OFF
Receptacle Switchpack no action"
Toggle
* This button must be in the second large or third small button location. Typical engraving is “Quiet Time”.
Standard Preset Buttons
Button
Address
Default Behavior
1st Press
Default Behavior
2nd Press
6
Raise all dimmers by 15%
Preset
7
Lower all dimmers by 15%
Preset
8
"Load 1, 2, 3 OFF
Alternate Voltage Switchpack OFF
Solatube Close (RC3DE only)
Emergency Relay OFF (RC3DE only) "
Preset
9
"Load 1 (Yellow) On, Load 2 (Red) OFF
All Dimmers to 50%
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Solatube Open (RC3DE only)
Emergency Relay ON (RC3DE only) "
Preset
10
"Load 1, 2, 3 On
All Dimmers to 100%
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Emergency Relay ON (RC3DE only) "
Preset
16
"Load 1, 2, 3 On
All Dimmers to 100%
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Solatube Open (RC3DE only)
Emergency Relay ON (RC3DE only) "
Preset
Control Type
17
Raise Dimmer 1 by 15%
Preset
18
Lower Dimmer 1 by 15%
Preset
19
Raise Dimmer 2 by 15%
Preset
20
Lower Dimmer 2 by 15%
Preset
21
Raise Dimmer 3 by 15%
Preset
22
Lower Dimmer 3 by 15%
Preset
Programmable Scene Buttons
Button
Address
Default Behavior
1st Press
Default Behavior
2nd Press
4
Turns ON Load 1 if OFF
All dimmers to 20%
Programmable Scene
12
"Load 1, 2, 3, ON
Dimmer 1=100%, dimmer 2=80%, dimmer 3=80%
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Solatube Open (RC3DE only)
Emergency Relay OFF (RC3DE only) "
Programmable Scene
13
"Load 1, 2, 3, ON
Dimmer 1=80%, dimmer 2=20%, dimmer 3=100%
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Solatube Open (RC3DE only)
Emergency Relay OFF (RC3DE only) "
Programmable Scene
14
"Load 1, 2, 3, ON
Dimmer 1=50%, dimmer 2=100%, dimmer 3=50%
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Solatube Open (RC3DE only)
Emergency Relay OFF (RC3DE only) "
Programmable Scene
15
"Load 1, 2, 3, ON
Dimmer 1=30%, dimmer 2=0%, dimmer 3=25%
Receptacle Switchpack ON
Alternate Voltage Switchpack ON
Solatube Open (RC3DE only)
Emergency Relay OFF (RC3DE only) "
Programmable Scene
Control Type