Fittings
This section offers a full selection of fittings and accessories to complete our strut system. Fittings are made from hot
rolled, pickled and oiled plate or strip steel in accordance with ASTM A1018 33,000 PSI min. yield, unless noted.
Dimensions
Hole Spacing –
17/8” (47.6 mm) on center
The following dimensions apply
to all fittings except as noted:
Hole Size – 9/16”
(14.3 mm) diameter
Hole Spacing –
13/16” (20.6 mm) from end
Thickness – 7/32” (5.5 mm)
Width –
15/8” (41.3 mm)
Materials & Finishes (Unless otherwise noted)
Finish
Code
PLN
Finish
Plain
ZN
Electro-Plated Zinc
GRN
HDG
SS4
SS6
AL
DURA GREEN™
Hot-Dipped Galvanized
Stainless Steel Type 304
Stainless Steel Type 316
Aluminum
Specification
ASTM A1018
33,000 PSI min. yield
ASTM B633 SC3 Type III
or ASTM A653
ASTM A123
ASTM A240
ASTM A240
ASTM B209
Strut Fittings
Note: A minimum order may apply on special
material and finishes.
Load Data
The load data published includes safety factor
of 2.5 when used with 12 ga. (2.6) channel
(safety factor = ratio of ultimate load to the
design load).
Use 1/2”-13 x 7/8” hex head cap screws and
1/2”-13 (N225 or TN225) channel nuts for the
rated results.
Recommended Bolt Torque
Hardware
Nuts and bolts are not included with the fittings
and must be ordered separately, unless noted.
Bolt Size
1/4”-20
5/16”-18
3/8”-16
1/2”-13
Foot/Lbs.
6
11
19
50
Nm
8
15
26
68
See chart on page 113 for setscrew torque.
Pre-Assembled Fittings
Some fittings are available with
hex head cap screws and
channel nuts pre-assembled.
These fittings and finishes will
be flagged using the following symbol.
4Dimension™ Strut System Compatible
These fittings and finishes will be
flagged using the following symbol.
PA
ZN
GRN
Metric
Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters.
73
Strut Systems
Flat Plate Fittings
B200-B202-2
SQUARE WASHER
• Standard finishes: ZN,
GRN, HDG, SS4, SS6, AL
15/8”
(41.3)
Hole Size A
Part
No.
B200
B201
B202
B202-1
B202-2
B202-3
A
In.
Bolt Size
mm
In.
3/8” (9.5)
7/16” (11.1)
9/16” (14.2)
Wt./C
mm
5/16” (7.9)
3/8” (9.5)
1/2” (12.7)
5/8” (15.9)
11/16” (17.4)
13/16” (20.6)
3/4” (19.0)
7/8” (22.2)
15/16” (23.8)
Lbs.
kg
18
18
17
16
15
14
(8.1)
(8.1)
B129
Two Hole Splice Plate
• Standard finishes: ZN, GRN
• Wt./C 37 Lbs. (16.8 kg)
PA
ZN
GRN
(7.7)
(7.2)
(6.8)
31/2”
(6.3)
(88.9)
NO TWIST SQUARE WASHER
B200D-B202-2D
• Standard finishes: ZN,
GRN, HDG, SS4, SS6, AL
15/8”
(41.3)
Hole Size A
Part
No.
B200D
B201D
B202D
B202-1D
B202-2D
A
In.
3/8”
Bolt Size
mm
In.
Wt./C
mm
5/16” (7.9)
3/8” (9.5)
(9.5)
7/16” (11.1)
9/16” (14.2)
1/2” (12.7)
5/8” (15.9)
11/16” (17.4)
13/16” (20.6)
3/4” (19.0)
Lbs.
kg
18
18
17
16
15
(8.1)
(8.1)
(7.7)
(7.2)
(6.8)
B340
Two Hole Splice Plate
B528
Two Hole Splice Plate
B141
Three Hole Splice Plate
• Standard finishes: ZN, GRN
• Wt./C 34 Lbs. (15.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 50 Lbs. (22.7 kg)
• Standard finishes: ZN, GRN
• Wt./C 55 Lbs. (24.9 kg)
ZN
PA GRN
21/2”
15/15” (63.5)
15/8”
(41.3)
31/4”
53/8”
(136.5)
(33.3)
(82.5)
45/8”
(117.5)
B557
Three Hole Splice Plate
B341
Four Hole Splice Plate
B342
Five Hole Splice Plate
• Standard finishes: ZN, GRN
• Wt./C 50 Lbs. (22.7 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 96 Lbs. (43.5 kg)
47/8”
(123.7)
ZN
PA GRN
(231.8)
(184.1)
15/8”
15/8” (41.3)
(41.3)
4Dimension compatible fitting
PA Pre-assembled fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
74
Strut Fittings
91/8”
71/4”
Flat Plate Fittings
B138
Two Hole Swivel Plate
B139
Three Hole Swivel Plate
B504
Four Hole Splice Plate
• Standard finishes: ZN, GRN
• Wt./C 48 Lbs. (21.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 69 Lbs. (31.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 73 Lbs. (33.1 kg)
45/8”
(117.5)
61/2”
3”
(165.1)
(41.3)
(88.9)
3”
17/8”
15/8”
31/2”
(76.2)
31/4”
(76.2)
(82.8)
(47.6)
B140
Three Hole Corner Plate
B143
Four Hole Corner Plate
B133
Four Hole Tee Plate
• Standard finishes: ZN, GRN,
HDG, SS4
• Wt./C 56 Lbs. (25.4 kg)
• Standard finishes: ZN, GRN,
HDG, SS4
• Wt./C 75 Lbs. (34.0 kg)
• Standard finishes: ZN, GRN, HDG,
SS4, AL
• Wt./C 75 Lbs. (34.0 kg)
31/2”
PA ZN
PA
ZN
GRN
PA
ZN
GRN
GRN
31/2”
(88.9)
(88.9)
31/2”
(88.9)
53/8”
31/2”
(136.5)
(88.9)
53/8”
(136.5)
B132
Five Hole Cross Plate
B135
Three Hole Corner Gusset Plate
B142
Four Hole Corner Gusset Plate
• Standard finishes: ZN, GRN, HDG
• Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 102 Lbs. (46.2 kg)
PA
ZN
GRN
PA
53/8”
31/2”
(136.5)
Strut Fittings
ZN
GRN
31/2”
(88.9)
(88.9)
31/2”
(88.9)
53/8”
53/8”
(136.5)
(136.5)
4Dimension compatible fitting
PA Pre-assembled fitting
Reference page 73 for general fitting and standard finish specifications.
75
Strut Systems
Flat Plate Fittings
B137
Four Hole Corner Gusset Plate
B556
Five Hole Corner Gusset Plate
B337
Three Hole Tee Gusset Plate
• Standard finishes: ZN, GRN
• Wt./C 273 Lbs. (123.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 145 Lbs. (65.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 70 Lbs. (31.7 kg)
25/16”
75/8”
(58.7)
(1183.7)
31/2”
513/16”
53/8”
(147.6)
1”
75/8”
(25.4)
(88.9)
(136.5)
53/8”
(136.5)
(193.7)
31/2”
31/2”
(88.9)
(88.9)
1”
(25.4)
B432
Four Hole Tee Gusset Plate
B136
Four Hole Tee Gusset Plate
B532
Five Hole Tee Gusset Plate
• Standard finishes: ZN, GRN
• Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 143 Lbs. (64.8 kg)
31/2”
31/2”
(88.9)
(88.9)
53/8”
53/8”
(136.5)
(136.5)
53/8”
(136.5)
53/8”
(136.5)
B339
Six Hole Tee Gusset Plate
B568
Six Hole Cross Gusset Plate
B334
Seven Hole Cross Gusset Plate
• Standard finishes: ZN, GRN
• Wt./C 149 Lbs. (67.6 kg)
• Standard finishes: ZN, GRN
• Wt./C 166 Lbs. (75.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 232 Lbs. (105.2 kg)
91/8”
31/2”
(88.9)
91/8”
(231.8)
(231.8)
31/2”
53/8”
(88.9)
(136.5)
4Dimension compatible fitting
PA Pre-assembled fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
76
Strut Fittings
91/8”
(231.8)
90° Angle Fittings
B420-378
One Hole Corner Angle
B420-578
One Hole Corner Angle
B420-778
One Hole Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 60 Lbs. (27.2 kg)
• Standard finishes: ZN, GRN
• Wt./C 85 Lbs. (38.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 107 Lbs. (48.5 kg)
17/8”
(47.6)
17/8”
17/8”
(47.6)
(47.6)
77/8”
57/8”
(200.0)
(149.2)
37/8”
(98.4)
B420-978
One Hole Corner Angle
B101
Two Hole Corner Angle
B230
Two Hole Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 129 Lbs. (58.5 kg)
• Standard finishes: ZN, GRN, HDG,
SS4, AL
• Wt./C 37 Lbs. (16.8 kg)
• Standard finishes: ZN, GRN, HDG,
SS4, AL
• Wt./C 37 Lbs. (16.8 kg)
PA
ZN
GRN
PA
15/8”
ZN
GRN
17/8”
(41.3)
17/8”
(47.6)
(47.6)
97/8”
(250.8)
21/16”
(52.4)
25/16”
(58.7)
B231
Two Hole “No-Twist”
Corner Angle
• Standard finishes: ZN, GRN, HDG
• Wt./C 41 Lbs. (18.6 kg)
Strut Fittings
PA
B359
Two Hole Corner Angle
B360
Two Hole Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 48 Lbs. (21.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 53 Lbs. (24.0 kg)
ZN
GRN
3”
31/2”
(76.2)
(88.9)
21/4”
(57.1)
21/4”
17/8”
(57.1)
(47.6)
PA
17/8”
(47.6)
4Dimension compatible fitting
Pre-assembled fitting
Reference page 73 for general fitting and standard finish specifications.
77
Strut Systems
90° Angle Fittings
B361
Two Hole Corner Angle
B102
Three Hole Corner Angle
B103
Three Hole Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 60 Lbs. (27.2 kg)
• Standard finishes: ZN, GRN, HDG, SS4
• Wt./C 56 Lbs. (25.4 kg)
• Standard finishes: ZN, GRN, HDG, SS4
• Wt./C 56 Lbs. (25.4 kg)
PA
ZN
GRN
PA
ZN
GRN
15/8”
31/2”
4”
(41.3)
(88.9)
(101.6)
41/8”
(104.8)
17/8”
21/4”
(47.6)
(57.1)
B232
Three Hole Corner Angle
B374
Three Hole Corner Angle
B529
Three Hole Corner Angle
• Standard finishes: ZN, GRN, HDG, SS4
• Wt./C 56 Lbs. (25.4 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 56 Lbs. (25.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 78 Lbs. (35.4 kg)
3”
PA
ZN
GRN
PA
ZN
GRN
21/16”
15/16”
(52.4)
(76.2)
(33.3)
17/8”
(47.6)
47/8”
(123.7)
315/16”
33/4”
(100.0)
(95.2)
21/2”
15/16” (63.5)
(33.3)
B104
Four Hole Corner Angle
B115
Four Hole Corner Angle
B558
Four Hole Corner Angle
• Standard finishes: ZN, GRN, HDG,
SS4, SS6, AL
• Wt./C 78 Lbs. (35.4 kg)
• Standard finishes: ZN, GRN, HDG,
SS4, AL
• Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 73 Lbs. (33.1 kg)
PA
ZN
GRN
PA
ZN
GRN
15/8”
(41.3)
33/4”
31/2”
(95.2)
(88.9)
Strut Fittings
21/4”
(57.1)
41/8”
(104.8)
315/16”
(100.0)
PA
15/8”
(41.3)
4Dimension compatible fitting
Pre-assembled fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
78
31/4”
(82.8)
90° Angle Fittings
B235R
Three Hole (Right Hand) Offset
Bent Angle
B235L
Three Hole (Left Hand) Offset
Bent Angle
B236R
Three Hole (Right Hand) Offset
Bent Angle
• 15/8” (41.3) from center to center of
the holes that are shown with bolt
heads
• Standard finishes: ZN, GRN
• Wt./C 53 Lbs. (24.0 kg)
• 15/8” (41.3) from center to center of
the holes that are shown with bolt
heads
• Standard finishes: ZN, GRN
• Wt./C 53 Lbs. (24.0 kg)
• Standard finishes: ZN, GRN
• Wt./C 65 Lbs. (29.5 kg)
17/8”
31/4”
31/4”
17/8”
(47.6)
(82.8)
(82.8)
(47.6)
21/16”
21/16”
(52.4)
(52.4)
(52.4)
• Standard finishes: ZN, GRN
• Wt./C 65 Lbs. (29.5 kg)
17/8”
(88.9)
B237
Three Hole Offset Bent Tee
B357
Four Hole Offset Bent Tee
• Standard finishes: ZN, GRN
• Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN, GRN
• Wt./C 77 Lbs. (34.9 kg)
47/8”
2”
(123.7)
(50.8)
(47.6)
(88.9)
31/2”
(47.6)
21/16”
B236L
Three Hole (Left Hand) Offset
Bent Angle
31/2”
17/8”
21/16”
(52.4)
53/8”
(136.5)
21/16”
Strut Fittings
(52.4)
B238R
Four Hole (Right Hand) Offset
Bent Tee
B238L
Four Hole (Left Hand) Offset
Bent Tee
• Standard finishes: ZN, GRN
• Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 76 Lbs. (34.5 kg)
21/16”
21/16”
(52.4)
(52.4)
B239
Five Hole Offset Bent Tee
• Standard finishes: ZN, GRN
• Wt./C 96 Lbs. (43.5 kg)
21/16”
(52.4)
33/4”
(95.2)
31/2”
31/2”
(88.9)
(88.9)
53/8”
(136.5)
33/4”
31/2”
(95.2)
(88.9)
Reference page 73 for general fitting and standard finish specifications.
79
Strut Systems
90° Angle Fittings
B844
Universal Shelf Bracket
• Standard finishes: ZN, GRN, HDG, SS4
• Wt./C 132 Lbs. (59.9 kg)
B844W
Universal Shelf Bracket Welded
B888W
Universal Shelf Bracket Welded
• Standard finishes: ZN, GRN
• Wt./C 134 Lbs. (60.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 197 Lbs. (89.4 kg)
4”
4”
(101.6)
(101.6)
513/16”
(147.6)
Welded
Corner
17/8”
(47.6)
4”
4”
(101.6)
(101.6)
17/8”
17/8”
(47.6)
(47.6)
53/8”
(136.5)
B234R
Four Hole (Right Hand)
Corner Gusset
B234L
Four Hole (Left Hand)
Corner Gusset
B134R
Four Hole (Right Hand)
Corner Gusset
• Standard finishes: ZN, GRN, HDG
• Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 100 Lbs. (45.3 kg)
31/2”
(88.9)
15/8”
31/2”
(88.9)
(41.3)
15/8”
315/16”
(41.3)
(100.0)
31/2”
(88.9)
43/16”
43/16”
(106.7)
(106.7)
17/8”
(47.6)
B134L
Four Hole (Left Hand)
Corner Gusset
B125
Three Hole Gussetted
Shelf Angle
B118
Four Hole Gussetted
Shelf Angle
• Standard finishes: ZN, GRN
• Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 67 Lbs. (30.4 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 102 Lbs. (46.2 kg)
315/16”
31/2”
(88.9)
31/2”
15/8”
(88.9)
31/2”
15/8”
(88.9)
(41.3)
25/16”
(58.7)
17/8”
(47.6)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
80
(41.3)
41/8”
(104.8)
Strut Fittings
(100.0)
90° Angle Fittings
B485
Four Hole Gussetted Shelf Angle
B533
Five Hole Gussetted Shelf Angle
• Standard finishes: ZN, GRN
• Wt./C 148 Lbs. (67.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 141 Lbs. (63.9 kg)
B126
Four Hole Gussetted Three
Way Shelf Angle
• Standard finishes: ZN, GRN
• Wt./C 101 Lbs. (45.8 kg)
17/8”
15/8”
(47.6)
(41.3)
31/2”
41/8”
(88.9)
(104.8)
31/2”
(88.9)
21/4”
53/8”
(57.1)
53/8”
(136.5)
(136.5)
315/16”
(100.0)
B127
Five Hole Gussetted Three
Way Shelf Angle
B503R
Six Hole (Right Hand)
Gussetted Corner Connection
B503L
Six Hole (Left Hand)
Gussetted Corner Connection
• Standard finishes: ZN, GRN
• Wt./C 135 Lbs. (61.2 kg)
• Standard finishes: ZN, GRN
• Wt./C 229 Lbs. (103.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 229 Lbs. (103.9 kg)
31/2”
33/4”
(88.9)
(95.2)
31/2”
(88.9)
33/4”
43/16” 43/16”
(95.2)
(106.7)
43/16”
(106.7)
(106.7)
53/8”
53/8”
(136.5)
(136.5)
15/8”
15/8”
(41.3)
(41.3)
B663
Seven Hole Gussetted Corner
Connection
B371
Two Hole Adjustable
Corner Angle
B372
Two Hole Adjustable
Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 289 Lbs. (131.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 41 Lbs. (18.6 kg)
• Standard finishes: ZN, GRN
• Wt./C 38 Lbs. (17.2 kg)
53/8”
Strut Fittings
(136.5)
53/8”
43/16”
(136.5)
25/8”
25/8”
(66.7)
(66.7)
(106.7)
9/16”
9/16”
(14.3)
9/16”
(14.3)
x 11/2” Slot
(50.8)
(38.1)
(14.3)
2”
9/16”
(14.3)
x 11/2” Slot
(38.1)
15/8”
(41.3)
15/8”
(41.3)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
81
Strut Systems
90° Angle Fittings
B496
Two Hole Adjustable
Corner Angle
B496-1
Two Hole Adjustable
Corner Angle
B371-2
Three Hole Adjustable
Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 85 Lbs. (38.5 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 58 Lbs. (26.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 61 Lbs. (27.6 kg)
23/8”
23/8”
(60.3)
(60.3)
15/16”
47/8”
67/8”
(33.3)
9/16”
(123.7)
(174.6)
9/16”
x 29/16” Slot
(14.3)
9/16”
(65.1)
x 29/16” Slot
(14.3)
17/8”
17/8”
(47.6)
(47.6)
(14.3)
x 11/2” Slot
25/8”
(38.1)
(66.7)
(65.1)
37/8”
(98.4)
B104SH
Three Hole Adjustable
Corner Angle
B461
Two Hole Adjustable
Corner Angle
B112
Four Hole Adjustable
Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 68 Lbs. (30.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 87 Lbs. (39.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 180 Lbs. (81.6 kg)
21/4”
31/2”
31/2”
(88.9)
(88.9)
13/32”
1/2”
(10.3)
(12.7)
(57.1)
9/16”
31/2”
(88.9)
9/16”
(14.3)
x 29/16” Slot
(65.1)
41/8”
(104.8)
9/16”
(14.3)
x 11/2” Slot (2)
(14.3)
(38.1)
33/4”
(95.2)
4”
(101.6)
x 29/16” Slot
(65.1)
65/8”
(168.3)
B113
Four Hole Adjustable
Corner Angle
• Standard finishes: ZN, GRN
• Wt./C 256 Lbs. (116.1 kg)
(14.3)
x 11/2” Slot
(38.1)
33/4”
B521
Two Hole Bus Duct Angle
• Standard finishes: ZN, GRN
• Wt./C 33 Lbs. (14.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 37 Lbs. (16.8 kg)
5/16”-18
Tapped
17/8”
(95.2)
1/2”
17/8”
(12.7)
(47.6)
(47.6)
6”
(152.4)
15/8”
85/8”
(219.1)
(41.3)
17/8”
(47.6)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
2”
(50.8)
82
Strut Fittings
9/16”
B109S
Two Hole Tapped Corner Angle
Angular Fittings
B147-B152
Two Hole Open Angle
B243-B253
Four Hole Open Angle
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
23/8”
(60.3)
11/16”
(27.0)
Part
No.
A
B147
B148
B149
B150
B151
B152
821/2°
Wt./C
Lbs.
75°
671/2°
60°
521/2°
371/2°
31/4”
(82.8)
A
kg
11/16”
(27.0)
63 (28.6)
Part
No.
A
B243
B244
B245
B246
B247
B248
B249
B250
B251
B252
B253
71/2°
Wt./C
Lbs.
15°
221/2°
30°
371/2°
45°
521/2°
60°
671/2°
75°
821/2°
kg
311/16”
77 (34.9)
B162-B165
Two Hole Open Angle
B322-B332
Two Hole Open Short Angle
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
11/16”
A
(27.0)
35/16”
(84.1)
Part
No.
A
B162
B163
B164
B165
30°
221/2°
15°
71/2°
Wt./C
Lbs.
kg
11/16”
21/16”
(52.4)
(27.0)
59 (26.7)
B154
Two Hole Open Angle
• Standard finishes: ZN, GRN, SS4
• Wt./C 58 Lbs. (26.3 kg)
Part
No.
A
B322
B323
B324
B325
B326
B327
B328
B329
B330
B331
B332
71/2°
B522
Three Hole 95°
Open Angle Fitting
(88.9)
Wt./C
Lbs.
15°
221/2°
30°
371/2°
45°
521/2°
60°
671/2°
75°
821/2°
A
(93.6)
31/2”
kg
A
13/4”
(44.4)
15/8”
(41.3)
35 (15.9)
B488
Two Hole Leg Connection
• Standard finishes: ZN, GRN
• Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 100 Lbs. (45.3 kg)
Strut Fittings
17/8”
(47.6)
3”
(76.2)
5°
5°
5°
11/16”
(27.0)
25/16”
45°
(58.7)
11/16”
35/8”
(92.1)
31/4”
(27.0)
(82.8)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
83
Strut Systems
Angular Fittings
B156 - B161
Two Hole Closed Angle
B155
Two Hole Closed Angle
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN, HDG, SS4
• Wt./C 63 Lbs. (28.6 kg)
PA
Part
No.
A
B156
B157
B158
B159
B160
B161
821/2°
75°
671/2°
60°
521/2°
371/2°
13/16”
13/16”
(20.6)
(20.6)
31/2”
(88.9)
33/16”
Wt./C
Lbs.
ZN
GRN
(80.9)
kg
13/16”
45°
(20.6)
A
56
13/16”
(25.4)
21/2”
(20.6)
21/2”
(63.5)
(63.5)
B363 - B369
Four Hole Closed Angle
B335-2 SERIES
Three Hole Adjustable Hinge
• Standard finishes: ZN, GRN
• OSHPD approved for Seismic Zone 4
• Standard finishes: ZN, GRN
5”
H
Hole Size
This Hole Only
(127.0)
411/16”
(119.1)
Part
No.
A
Wt./C
Lbs.
821/2°
75°
671/2°
60°
521/2°
45°
371/2°
B363
B364
B365
B366
B367
B368
B369
43/8”
kg
213/16”
(111.1)
(71.4)
Part No.
& Size
A
95 (43.1)
Hole Size H
In.
mm
7/16” (11.1)
9/16” (14.3)
B335-2-3/8
B335-2-1/2
B335-2-5/8
B335-2-3/4
11/16” (17.4)
13/16” (20.6)
Wt./C
Lbs.
kg
96
94
92
90
(43.2)
(42.3)
(41.4)
(40.5)
B335
Four Hole Adjustable Hinge
B335V
Three Hole Half Hinge
B335-1
Two Hole Adjustable Hinge
• Standard finishes: ZN, GRN
• Wt./C 110 Lbs. (49.9 kg)
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
• Wt./C 78 Lbs. (35.4 kg)
Part No.
& Size
411/16”
(119.1)
In.
mm
9/16” (14.3)
11/16” (17.4)
13/16” (20.6)
Wt./C
Lbs.
kg
53
54
55
(24.1)
(24.5)
(24.9)
213/16”
H
(71.4)
213/16”
(71.4)
411/16”
411/16”
(119.1)
(119.1)
PA
Pre-assembled fitting
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
84
Strut Fittings
B335V-1/2
B335V-5/8
B335V-3/4
Hole Size H
Angular Fittings
B634
Single Channel Adjustable Brace
B635
Double Channel Adjustable Brace
• Standard finishes: ZN, GRN
• Wt./C 306 Lbs. (138.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 518 Lbs. (234.9 kg)
13/16”
13/16”
(20.6)
(20.6)
15/8”
15/8”
(41.3)
(41.3)
30°
MIN.
17/8”
17/8”
(47.6)
(47.6)
33/4”
33/4”
(95.2)
(95.2)
53/8”
53/8”
(136.5)
(136.5)
B129
B650 SERIES
Seismic Retrofit Bracket
•
•
•
•
•
OSHPD approved for Seismic Zone 4.
Available for 3/8”, 1/2”, 5/8”, and 3/4” threaded rods.
Allows installer to easily brace existing trapeze supports.
Includes: Bracket, B129 plate, & key. Hardware sold separately.
Standard finish: ZN, GRN
ATR
Bracket
Key
Part No.
& Size
For
Rod Size
B650-3/8
3/8”
B650-1/2
B650-5/8
B650-3/4
1/2”
5/8”
3/4”
TL
LL
Wt./C
Lbs.
kN
Lbs.
kN
Lbs.
kg
1100
1500
1500
1500
(4.89)
1100
1500
1500
1500
(4.89)
92
97
95
107
(41.4)
(6.67)
(6.67)
(6.67)
(6.67)
(6.67)
(6.67)
Longitudinal
Load (LL)
(43.6)
(42.7)
Transverse
Load (TL)
(48.5)
B633
Adjustable Seismic Hinge Fitting
H
Strut Fittings
• B633-1/2 thru B633-7/8 - OSHPD approved for Seismic Zone 4.
• Use 1/2” Bolt & Channel Nut on two hole side of
Connector Fitting (Torque to 50 ft.-lbs.)
• Allows for swivel in two planes.
• Standard finish: ZN
33/4”
(95.2)
B
15/8”
(41.3)
Part No.
& Size
B633-1/2
A
In.
B
mm
31/2” (82.5)
31/2” (82.5)
B633-5/8
B633-3/4
31/2” (82.5)
B633-7/8
39/16” (90.5)
B633-1
39/16” (90.5)
B633-11/8 39/16” (90.5)
B633-11/4 37/8” (98.4)
In.
mm
Hole Size H
In.
mm
15/8” (41.3)
15/8” (41.3)
9/16” (14.3)
11/16” (17.4)
15/8”
2”
2”
2”
21/4”
13/16” (20.6)
15/16” (23.8)
(41.3)
(50.8)
(50.8)
(50.8)
(57.1)
11/16” (27.0)
13/16” (30.2)
15/16” (33.3)
Wt./C
Lbs.
kg
92
97
95
107
120
104
114
(41.4)
A
(43.6)
(42.7)
(48.5)
(54.0)
(47.2)
(51.7)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
85
Strut Systems
Braces
B261 - Two Hole 45° Knee Brace
• Standard finishes: ZN, GRN
• Design load determined by testing using a B335 hinged corner connection.
• Load ratings are for brace members only. Do not exceed allowable beam
or column loads for strut channels.
• Safety Factor of 3
Part
No.
B261-8
B261-12
B261-16
B261-18
B261-24
B261-36
A
In.
B
mm
In.
Design Load
mm
73/8” (187.3)
101/8” (257.2)
8”
12” (304.8)
165/8” (422.3) 133/8” (339.7)
18” (457.2) 147/16” (366.7)
24” (609.6) 1811/16”(474.7)
36” (914.4) 273/16” (690.6)
(203.2)
Lbs.
kN
Lbs.
1020
530
450
250
110
165
218
234
303
441
(2.00)
(1.11)
(.49)
Design Load
B
A
kg
119 (54.0)
(2.36)
(41.3)
Wt./C
1500 (6.67)
(4.54)
15/8”
(74.8)
(98.9)
45°
15/8”
(41.3)
(106.1)
(137.4)
B
(200.0)
B631 - Two Hole 45° Tubing Knee Brace
•
•
•
•
•
1” (25.4) Square steel tubing
Material: ASTM A513
Standard finishes: ZN, GRN
Design load determined by testing using a B335 hinged corner connection.
Load ratings are for brace members only. Do not exceed allowable beam
or column loads for strut channels.
• Safety Factor of 3
Part
No.
B631-18
B631-24
B631-30
B631-36
B631-42
B631-48
B631-54
B631-60
B631-72
B631-84
B631-96
Design Load
A
mm
Lbs.
kN
Lbs.
kg
18”
24”
30”
36”
42”
48”
54”
60”
72”
84”
96”
(457.2)
1500
1500
1500
1500
1230
940
740
600
420
310
240
(6.67)
145
186
225
266
307
348
389
430
508
589
669
(65.8)
(762.0)
(914.4)
(1066.8)
(1219.2)
(1371.6)
(1524.0)
(1828.8)
(2133.6)
(2438.4)
(6.67)
(6.67)
(6.67)
(5.47)
(4.18)
(3.29)
(2.67)
(1.87)
(1.38)
(1.07)
A
Wt./C
In.
(609.6)
Design Load
(84.4)
(102.0)
(120.6)
(139.2)
(157.8)
(176.4)
(195.0)
(230.4)
13/4”
(267.2)
(44.4)
(303.5)
B632 - Two Hole Straight Tubing Brace
• 1” (25.4) Square steel tubing
• Material: ASTM A513
• Standard finishes: ZN, GRN
Part
No.
Wt./C
mm
Lbs.
kg
18”
24”
30”
36”
42”
48”
54”
60”
72”
84”
96”
(457.2)
133
174
215
256
295
335
380
420
500
585
670
(60.3)
13/4”
(78.9)
(44.4)
(609.6)
(762.0)
(914.4)
(1066.8)
(1219.2)
(1371.6)
(1524.0)
(1828.8)
(2133.6)
(2438.4)
(97.5)
(116.1)
(133.8)
A
(151.9)
(172.3)
(190.5)
(226.8)
(265.3)
(303.9)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
86
Strut Fittings
B632-18
B632-24
B632-30
B632-36
B632-42
B632-48
B632-54
B632-60
B632-72
B632-84
B632-96
A
In.
Clevis Fittings
B169
Two Hole Splice
Clevis For B52
B168
Three Hole Splice
Clevis For B52
B167
Four Hole Splice
Clevis For B52
• Standard finishes: ZN, GRN
• Wt./C 84 Lbs. (38.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 126 Lbs. (57.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 178 Lbs. (80.7 kg)
PA
31/2”
(88.9)
1/4”
GRN
53/8”
71/4”
(136.5)
(184.1)
1/4”
(6.3)
1/4”
(6.3)
(6.3)
B170
Two Hole Splice
Clevis For B22 or B52A
B171
Three Hole Splice
Clevis For B22 or B52A
B172
Four Hole Splice
Clevis For B22 or B52A
• Standard finishes: ZN, GRN
• Wt./C 123 Lbs. (55.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 195 Lbs. (88.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 266 Lbs. (120.6 kg)
PA
31/2”
1/4”
ZN
GRN
53/8”
(88.9)
71/4”
(136.5)
(6.3)
(184.1)
1/4”
1/4”
(6.3)
(6.3)
B172-12
Four Hole Splice Clevis For B12
• Standard finishes: ZN, GRN
• Wt./C 326 Lbs. (147.8 kg)
B172-22A
Four Hole Splice
Clevis For B11 or B22A
• Standard finishes: ZN, GRN
• Wt./C 406 Lbs. (184.1 kg)
PA
B450
U-Washer
• Material: ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
H
Hole Size
GRN
15/32”
Strut Fittings
(11.9)
15/8”
11 Gauge (3.1)
Part No.
& Size
71/4”
(184.1)
71/4”
B450-1/4
(184.1)
B450-3/8
B450-1/2
B450-5/8
B450-3/4
1/4”
1/4”
(6.3)
(6.3)
PA
(41.3)
Hole Size H
Lbs.
kg
5/16” (7.9)
7/16” (11.1)
9/16” (14.3)
11/16” (17.4)
13/16” (20.6)
Wt./C
Lbs.
kg
14
14
13
13
13
(6.3)
(6.3)
(5.8)
(5.8)
(5.8)
Pre-assembled fitting.
Reference page 73 for general fitting and standard finish specifications.
87
Strut Systems
‘U’ Fittings
B527
Three Hole Offset Plate
Connection
• Standard finishes: ZN, GRN
• Wt./C 54 Lbs. (24.5 kg)
B116-52
Three Hole U-Support
B116-42
Three Hole U-Support
• Standard finishes: ZN, GRN
• Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN
• Wt./C 75 Lbs. (34.0 kg)
1/2”
13/16”
(12.7)
1”
(20.6)
(25.4)
57/16”
57/16”
(138.1)
(138.1)
55/16”
(134.9)
B116-32
Three Hole U-Support
B116-32A
Three Hole U-Support
B116-12
Three Hole U-Support
• Standard finishes: ZN, GRN
• Wt./C 84 Lbs. (38.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 116 Lbs. (52.6 kg)
• Standard finishes: ZN, GRN
• Wt./C 108 Lbs. (49.0 kg)
13/8”
23/4”
27/16”
(69.8)
(61.9)
(34.9)
57/16”
57/16”
57/16”
(138.1)
(138.1)
(138.1)
B107
Five Hole U-Support
B107-22A
Three Hole U-Support
B588
Three Hole U-Support
• Standard finishes: ZN, GRN, HDG
• Wt./C 85 Lbs. (38.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 126 Lbs. (57.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 157 Lbs. (71.2 kg)
PA
ZN
GRN
15/8”
Strut Fittings
47/8”
31/4”
(123.7)
(82.8)
(41.3)
57/16”
57/16”
(138.1)
(138.1)
PA
57/16”
Pre-assembled fitting.
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
88
(138.1)
‘U’ Fittings
B412
Three Hole
Offset U-Support
• Standard finishes: ZN, GRN
• Wt./C 89 Lbs. (40.3 kg)
B107S
Five Hole U-Support
B596
Three Hole Swivel Clevis
• Material: 7 Gauge (4.5)
ASTM A1011 33,000 PSI min. yield
• Standard finishes: ZN, GRN
• Wt./C 51 Lbs. (23.1 kg)
• Material: 7 Gauge (4.5)
• Standard finishes: ZN, GRN
• Wt./C 53 Lbs. (24.0 kg)
57/16”
33/4”
(138.1)
(95.2)
1”
17/8”
(25.4)
(47.6)
13/16”
(20.6)
13/8”
(34.9)
21/4”
(57.1)
13/4”
7/16” (11.1) Dia.
4 Holes
9/16” (14.3) Dia.
15/8”
15/8”
(41.3)
(41.3)
(44.4)
B578
Three Hole Light-Weight
U-Support
• Material: 10 Gauge (3.4)
ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
• Wt./C 18 Lbs. (8.1 kg)
B594
Five Hole U-Support
B266
Six Hole U-Support
• Standard finishes: ZN, GRN
• Wt./C 106 Lbs. (48.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 105 Lbs. (47.6 kg)
35/16”
17/8”
121/32”
(84.1)
(42.1)
(47.6)
311/16”
(93.6)
3/4”
(19.0)
15/8”
(41.3)
13/32”
(10.3)
15/8”
(41.3)
9/32” (7.1)
3 Holes
71/32”
Dia.
35/16”
(178.6)
111/16”
71/16”
(42.8)
(84.1)
(179.4)
B425
Six Hole U-Support
B581
Eight Hole U-Support
B519
Eight Hole U-Support
• Standard finishes: ZN, GRN
• Wt./C 167 Lbs. (75.7 kg)
• Standard finishes: ZN, GRN
• Wt./C 201 Lbs. (91.2 kg)
• Standard finishes: ZN, GRN
• Wt./C 266 Lbs. (102.5 kg)
111/16”
Strut Fittings
(42.9)
31/2”
31/2”
(88.9)
(88.9)
15/8”
31/2”
(41.3)
(88.9)
31/2”
(88.9)
15/8”
(41.3)
57/16”
71/16”
(138.1)
(179.4)
513/32”
(137.3)
Reference page 73 for general fitting and standard finish specifications.
89
Strut Systems
‘U’ Fittings
B333
Slotted Three Hole
U-Support For B22
B451
Slotted Three Hole U-Support
With Gusset For B22
A
• Standard finishes: ZN, GRN
• Consists of B333-1, 2, or 3 with
gusset plate welded on back.
• Material: ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
C
9/16”
A
x 11/2” Slots (2)
(14.3)
(38.1)
9/16”
x 11/2” Slots (2)
(14.3)
(38.1)
15/8”
B
(41.3)
Part
No.
A
In.
B
mm
In.
C
mm
In.
Wt./C
mm
B333-1 71/2” (190.5) 15/16” (33.3) 27/8” (73.0)
B333-2 81/2” (215.9) 115/16”(49.2) 33/8” (85.7)
B333-3 103/8” (263.5) 27/8” (73.0) 45/16”(109.5)
B408
Two Hole Bus Duct Clevis
Lbs.
Part
No.
kg
103 (46.7)
115 (52.1)
135 (61.2)
(12.7)
In.
B451-1
B451-2
B451-3
Wt./C
mm
Lbs.
1
7 /2”(190.5)
81/2”(215.9)
103/8”(263.5)
kg
137 (62.1)
156 (70.7)
172 (78.0)
B358
Two Hole Clevis
1/2”
• Standard finishes: ZN, GRN
A
13/16”
• Standard finishes: ZN, GRN
(20.6)
9/16” (14.3)
17/8”
17/8”
Dia.
2 Holes
(47.6)
(47.6)
A
Part
No.
A
In.
B408-1
B408-2
B408-3
A
Wt./C
mm
213/32”(61.1)
325/32”(96.0)
43/4”(762.0)
Lbs.
kg
58 (26.3)
76 (34.5)
88 (39.9)
13/16”
(20.6)
Part
No.
In.
mm
Lbs.
kg
B358-4
B358-5
B358-6
B358-7
B358-8
4”
5”
6”
7”
8”
(101.6)
89
93
106
118
132
(40.3)
B173
Four Hole Clevis
B595
Three Hole Clevis
• Standard finishes: ZN, GRN
• Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN, GRN
• Wt./C 75 Lbs. (34.0 kg)
Wt./C
(127.0)
(152.4)
(177.8)
(203.2)
(42.2)
(48.1)
13/16”
(53.5)
(20.6)
(59.9)
B405
Three Hole
Suspension Clevis
• Standard finishes: ZN, GRN
• Wt./C 75 Lbs. (34.0 kg)
17/8”
37/16”
(47.6)
(87.3)
(47.6)
129/32”
35/16”
(84.1)
121/32”
(42.0)
(48.4)
35/16”
121/32”
(42.0)
(84.1)
17/8”
(47.6)
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
90
Strut Fittings
17/8”
A
‘U’ Fittings
B398-1
Three Hole Cup Support
B400
Three Stud Ring Connection
• Standard finishes: ZN, GRN
• Wt./C 73 Lbs. (33.1 kg)
• 1/2”-13 stud protrudes 1”
(25.4mm)
• Standard finishes: ZN
• Wt./C 85 Lbs. (38.5 kg)
111/16”
(42.9)
111/16”
23/32”
23/8”
(53.2)
(55.6)
15/8”
11/16”
(41.3)
(27.0)
B400-1
One Stud Ring Connection
B400-2
One Stud Ring Connection
• 1/2”-13 stud protrudes 1” (25.4mm)
• Standard finishes: ZN
• Wt./C 53 Lbs. (24.0 kg)
• 1/2”-13 stud protrudes 1” (25.4mm)
• Standard finishes: ZN
• Wt./C 40 Lbs. (18.1 kg)
17/8”
111/16”
111/16”
17/8”
(42.9)
Strut Fittings
(47.6)
(47.6)
(42.9)
B400-3
Two Stud Ring Connection
B400-4
Two Stud Ring Connection
• 1/2”-13 stud protrudes 1” (25.4mm)
• Standard finishes: ZN
• Wt./C 59 Lbs. (26.7 kg)
• 1/2”-13 stud protrudes 1” (25.4mm)
• Standard finishes: ZN
• Wt./C 59 Lbs. (26.7 kg)
111/16”
(42.9)
111/16”
111/16”
111/16”
(42.9)
(42.9)
(42.9)
(42.9)
Reference page 73 for general fitting and standard finish specifications.
91
Strut Systems
‘Z’ Fittings
B526
Two Hole Offset Z-Support
• Standard finishes: ZN, GRN
• Wt./C 38 Lbs. (17.2 kg)
B106-52
Two Hole Offset Z-Support
for B52
B106-42
Two Hole Offset Z-Support
for B42
• Standard finishes: ZN, GRN
• Wt./C 40 Lbs. (18.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 44 Lbs. (20.0 kg)
1/4”
(6.3)
315/32”
13/16”
1”
(20.6)
(25.4)
(88.1)
15/8”
31/2”
31/2”
(88.9)
(88.9)
(41.3)
B106-32
Two Hole Offset Z-Support
for B32
B106-12
Two Hole Offset Z-Support
for B12
B105
Three Hole Offset Z-Support
for B22
• Standard finishes: ZN, GRN
• Wt./C 51 Lbs. (23.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 63 Lbs. (28.6 kg)
• Standard finishes: ZN, GRN, HDG
• Wt./C 51 Lbs. (23.1 kg)
15/8”
(41.3)
27/16”
13/8”
(61.9)
(34.9)
31/2”
31/2”
31/2”
(88.9)
(88.9)
(88.9)
B110
Three Hole Offset Z-Support
for B11
• Standard finishes: ZN, GRN
• Wt./C 70 Lbs. (31.7 kg)
B586
Two Hole Z-Support
B108
Two Hole Offset Z-Support
• Standard finishes: ZN, GRN
• Wt./C 90 Lbs. (40.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 55 Lbs. (24.9 kg)
31/2”
(88.9)
31/2”
31/2”
(88.9)
Strut Fittings
(88.9)
21/8”
47/8”
15/8”
(123.7)
(54.0)
(41.3)
31/2”
(88.9)
15/8”
(41.3)
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
92
‘Z’ Fittings
B387
Two Hole Z-Bus Duct Connection
B407
Two Hole Z-Sopport
• Standard finishes: ZN, GRN
15/8”
• Standard finishes: ZN, GRN
B111
Three Hole Sheath
Corner Connection
• Standard finishes: ZN, GRN
• Wt./C 68 Lbs. (30.8 kg)
31/2”
(41.3)
(88.9)
31/2”
31/2”
15/8”
(88.9)
1/2”
31/2”
(88.9)
(41.3)
(88.9)
A
(12.7)
15/8”
(41.3)
Part
No.
A
Part
No.
A
In.
Wt./C
mm
B387 43/4” (120.6)
B387-1 325/32” (96.0)
B387-2 213/32” (61.1)
Lbs.
kg
89
78
62
(40.3)
(35.4)
(28.1)
B407-4
B407-5
B407-6
B407-7
B407-8
B407-95/8
A
In.
Wt./C
mm
4” (101.6)
5” (127.0)
6” (152.4)
7” (177.8)
8” (203.2)
95/8” (244.5)
Lbs.
kg
77
95
98
105
120
138
(34.9)
(43.1)
(44.4)
15/8”
(47.6)
(41.3)
(54.4)
(62.6)
B410-52
Channel Hanger Bracket for B52
B410-32
Channel Hanger Bracket for B32
B410-22
Channel Hanger Bracket for B22
• Material: 11 Gauge (3.0)
ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
• Wt./C 6.7 Lbs. (3.0 kg)
• Material: 11 Gauge (3.0)
ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
• Wt./C 8.3 Lbs. (3.7 kg)
• Material: 11 Gauge (3.0)
ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
• Wt./C 9 Lbs. (4.1 kg)
13/16”
9/32” (7.1)
(20.6)
13/16”
13/16”
(20.6)
(20.6)
Dia. Hole
9/32” (7.1)
9/32” (7.1)
Dia. Hole
Dia. Hole
Strut Fittings
15/8”
13/16”
13/8”
(20.6)
(34.9)
(41.3)
B410-12
Channel Hanger Bracket for B12
B410-11
Channel Hanger Bracket for B11
B580
Five Hole Gussetted Z-Support
• Material: 11 Gauge (3.0)
ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
• Wt./C 11.2 Lbs. (5.1 kg)
• Material: 11 Gauge (3.0)
ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
• Wt./C 13.4 Lbs. (6.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 100 Lbs. (45.3 kg)
31/2”
(88.9)
9/32” (7.1)
13/16”
Dia. Hole
(20.6)
13/16”
31/2”
(88.9)
(20.6)
9/32” (7.1)
Dia. Hole
27/16”
31/4”
(82.8)
15/8”
(61.9)
(41.3)
Reference page 73 for general fitting and standard finish specifications.
93
Strut Systems
‘Z’ & Wing Fittings
B515
Adjustable Offset Gussetted Z-Support
B428
Eight Hole Gussetted Corner Connection
• Standard finishes: ZN, GRN
• Wt./C 93 Lbs. (42.2 kg)
• Standard finishes: ZN, GRN
• Wt./C 203 Lbs. (92.1 kg)
15/32”
31/2”
(11.9)
53/4”
17/8”
(146.0)
53/4”
(47.6)
(88.9)
9/16”
(14.3)
37/8”
(98.4)
(146.0)
x 29/16” Slots
(65.1)
17/8”
(47.6)
31/2”
(88.9)
B267R
Three Hole Single Corner
Connection (Right Hand)
B267L
Three Hole Single Corner
Connection (Left Hand)
B270R
Four Hole Single Corner
Connection (Right Hand)
• Standard finishes: ZN, GRN
• Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN
• Wt./C 77 Lbs. (34.9 kg)
111/16”
21/16”
21/16”
(52.4)
(52.4)
(42.8)
21/16”
(52.4)
15/8”
15/8”
(41.3)
(41.3)
31/2”
(88.9)
31/2”
313/16”
(88.9)
(96.8)
B270L
Four Hole Single Corner
Connection (Leftt Hand)
B268R
Five Hole Single Corner
Connection (Right Hand)
B268L
Five Hole Single Corner
Connection (Left Hand)
• Standard finishes: ZN, GRN
• Wt./C 77 Lbs. (34.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 100 Lbs. (45.3 kg)
Strut Fittings
111/16”
(42.8)
21/16”
315/16”
(52.4)
15/8”
(100.0)
315/16”
(100.0)
(41.3)
313/16”
(96.8)
31/2”
(88.9)
(41.3)
31/2”
(88.9)
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
15/8”
94
Wing Fittings
B269R
Six Hole Single Corner
Connection (Right Hand)
B269L
Six Hole Single Corner
Connection (Left Hand)
B119
Six Hole Double Corner
Connection
• Standard finishes: ZN, GRN
• Wt./C 120 Lbs. (54.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 120 Lbs. (54.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 71 Lbs. (32.2 kg)
31/2”
31/2”
(88.9)
(88.9)
315/16”
315/16”
(100.0)
(100.0)
21/16”
15/8”
(52.4)
(41.3)
31/2”
53/8”
53/8”
(88.9)
(136.5)
(136.5)
B120
Six Hole Double
Corner Connection
B121
Eight Hole Double
Corner Connection
B271
Five Hole Double
Wing Connection
• Standard finishes: ZN, GRN
• Wt./C 110 Lbs. (49.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 152 Lbs. (68.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 95 Lbs. (43.1 kg)
57/16”
(138.1)
31/2”
15/8”
(41.3)
315/16”
(88.9)
315/16”
21/16”
(100.0)
(100.0)
(52.4)
15/8”
Strut Fittings
(41.3)
31/2”
53/8”
111/16”
(88.9)
(136.5)
(42.8)
B272
Eight Hole Double
Wing Connection
B273
Ten Hole Double
Wing Connection
B122
Six Hole Triple
Wing Connection
• Standard finishes: ZN, GRN
• Wt./C 156 Lbs. (70.7 kg)
• Standard finishes: ZN, GRN
• Wt./C 185 Lbs. (83.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 110 Lbs. (49.9 kg)
57/16”
93/16”
(138.1)
(233.4)
57/16”
(138.1)
315/16”
15/8”
315/16”
(100.0)
31/2”
(41.3)
21/16”
(100.0)
(52.4)
(88.9)
15/8”
111/16”
111/16”
111/16”
(42.8)
(42.8)
(42.8)
(41.3)
Reference page 73 for general fitting and standard finish specifications.
95
Strut Systems
Wing Fittings
B123
Twelve Hole Triple
Wing Connection
B124
Nine Hole Triple
Wing Connection
B276
Fourteen Hole Double Corner
Gussetted Connection
• Standard finishes: ZN, GRN
• Wt./C 234 Lbs. (106.1 kg)
• Standard finishes: ZN, GRN
• Wt./C 177 Lbs. (80.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 196 Lbs. (88.9 kg)
57/16”
93/16”
(138.1)
(233.4)
4”
(101.6)
315/16”
31/2”
315/16”
(100.0)
(88.9)
(100.0)
15/8”
(41.3)
111/16”
4”
111/16”
(42.8)
(101.6)
(42.8)
B274R
Eight Hole Single Corner
Gussetted Connection
(Right Hand)
B274L
Eight Hole Single Corner
Gussetted Connection
(Left Hand)
• Standard finishes: ZN, GRN
• Wt./C 176 Lbs. (79.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 176 Lbs. (79.8 kg)
B495
Ten Hole Double Wing
Gussetted Connection
• Standard finishes: ZN, GRN
• Wt./C 240 Lbs. (108.8 kg)
93/16”
511/16”
521/32”
(144.5)
(233.4)
(143.7)
315/16”
315/16”
(100.0)
(100.0)
31/2”
37/8”
(98.4)
31/2”
31/2”
(88.9)
(88.9)
(88.9)
111/16”
111/16”
(42.8)
(42.8)
111/16”
(42.8)
B277
Twelve Hole Triple Wing
Gussetted Connection
B362
Eight Hole Double Corner
Gussetted Connection
• Standard finishes: ZN, GRN
• Wt./C 285 Lbs. (129.3 kg)
• Standard finishes: ZN, GRN
• Wt./C 226 Lbs. (102.5 kg)
B571
Eight Hole Wing Connection
• Standard finishes: ZN, GRN
• Wt./C 201 Lbs. (91.2 kg)
93/16”
53/8”
(136.5)
4”
(101.6)
315/16”
315/16”
(100.0)
31/2”
(88.9)
31/2”
(88.9)
111/16”
(42.8)
15/8”
(41.3)
4”
(101.6)
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
(100.0)
96
Strut Fittings
(233.4)
Wing Fittings & Post Bases
B346L
Eight Hole Double Corner Gussetted Connection
(Left Hand)
B346R
Eight Hole Double Corner Gussetted Connection
(Right Hand)
• Standard finishes: ZN, GRN
• Wt./C 242 Lbs. (109.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 242 Lbs. (109.8 kg)
53/8”
53/8”
(136.5)
(136.5)
31/2”
31/2”
(88.9)
(88.9)
B279
Post Base for B22
B279SQ
Post Base for B22
B279FL
Post Base for B22
• Standard finishes: ZN, GRN
• Wt./C 314 Lbs. (142.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 314 Lbs. (142.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 230 Lbs. (104.3 kg)
3/4” (19.0)
111/16”
3/4” (19.0)
4 Holes
Dia. 2 Holes
(42.8)
Dia.
(42.8)
6”
111/16”
3/4” (19.0)
111/16”
Dia. 4 Holes
(42.8)
15/8”
(41.3)
15/8”
15/8”
(41.3)
(152.4)
(41.3)
41/4”
6”
8”
41/4”
(107.9)
(203.2)
(107.9)
(152.4)
6”
61/4”
(158.7)
3”
6”
(152.4)
(76.2)
(152.4)
3”
(76.2)
B280
Post Base for B22
B280SQ
Post Base for B22
B280FL
Post Base for B22
• Standard finishes: ZN, GRN, HDG,
SS4, AL
• Wt./C 392 Lbs. (177.8 kg)
• Standard finishes: ZN, GRN, HDG,
SS4, AL
• Wt./C 392 Lbs. (177.8 kg)
• Standard finishes: ZN, GRN, HDG, SS4
• Wt./C 312 Lbs. (141.5 kg)
Strut Fittings
111/16”
3/4” (19.0)
(42.8)
Dia. 4 Holes
(42.8)
3/4” (19.0)
3/4” (19.0)
31/2”
Dia.
2 Holes
Dia. 4 Holes
31/2”
(88.9)
6”
111/16”
(42.8)
111/16”
(88.9)
31/2”
(152.4)
61/4”
41/4”
6”
6”
(152.4)
8”
41/4”
(107.9)
(107.9)
(152.4)
3”
(88.9)
(158.7)
(203.2)
6”
3”
(152.4)
(76.2)
(76.2)
Reference page 73 for general fitting and standard finish specifications.
97
Strut Systems
Post Bases
B281A
Post Base for B22A, B, C, ETC.
B281ASQ
Post Base for B22A, B, C, Etc.
B281AFL
Post Base for B22A, B, C, Etc.
• Standard finishes: ZN, GRN
• Wt./C 330 Lbs. (149.7 kg)
• Standard finishes: ZN, GRN
• Wt./C 330 Lbs. (149.7 kg)
• Standard finishes: ZN, GRN
• Wt./C 250 Lbs. (113.4 kg)
3/4” (19.0)
Dia. 4 Holes
35/16”
15/8”
35/16”
(41.3)
(84.1)
3/4” (19.0)
(84.1)
Dia.
35/16”
2 Holes
3/4” (19.0)
(84.1)
Dia. 4 Holes
15/8”
6”
(41.3)
(152.4)
41/4”
(107.9)
41/4”
6”
(152.4)
8”
(107.9)
(152.4)
6”
15/8”
61/4”
6”
(41.3)
(158.7)
(203.2)
(152.4)
3”
3”
(76.2)
(76.2)
B281
Post Base for B22A, B, C, Etc.
B281SQ
Post Base for B22A, B, C, Etc.
B281FL
Post Base for B22A, B, C, Etc.
• Standard finishes: ZN, GRN, HDG
• Wt./C 400 Lbs. (181.4 kg)
• Standard finishes: ZN, GRN, HDG,
SS4
• Wt./C 400 Lbs. (181.4 kg)
• Standard finishes: ZN, GRN
• Wt./C 320 Lbs. (145.1 kg)
3/4” (19.0)
Dia.
4 Holes
35/16”
(84.1)
35/16”
31/2”
(84.1)
(88.9)
3/4” (19.0)
3/4” (19.0)
Dia. 4 Holes
4 Holes
35/16”
Dia.
(84.1)
31/2”
(88.9)
6”
31/2”
(152.4)
6”
(152.4)
41/4”
41/4”
(107.9)
8”
(107.9)
6”
(88.9)
61/4”
(158.7)
(203.2)
6”
(152.4)
(152.4)
3”
3”
(76.2)
(76.2)
B281M
Post Base for B22-2PL
B281MSQ
Post Base for B22-2PL
• Standard finishes: ZN, GRN
• Wt./C 470 Lbs. (213.2 kg)
• Standard finishes: ZN, GRN
• Wt./C 470 Lbs. (213.2 kg)
B570
Post Base for Four
Channel Combinations
• Standard finishes: ZN, GRN
• Wt./C 397 Lbs. (180.1 kg)
39/16”
(90.5)
3/4” (19.0)
Dia. 4 Holes
(42.8)
15/8”
31/2”
3/4” (19.0)
(41.3)
(88.9)
Dia. 4 Holes
31/2”
315/32”
(88.9)
(87.9)
(152.4)
(152.4)
(107.9)
(152.4)
3”
3”
(76.2)
(76.2)
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
(152.4)
41/4”
6” (107.9)
(152.4)
6”
6”
6”
(6.3)
41/4”
6”
1/4”
98
6”
(152.4)
3/4” (19.0)
4 Holes
Dia.
Strut Fittings
111/16”
Post Bases & Brackets
B570A
Post Base for Four
Channel Combinations
B278
Post Base for B22
B300
Post Base
B585
Post Base for B22A
• Material: Malleable Iron
• Standard finishes: ZN, GRN
• Wt./C 259 Lbs. (117.5 kg)
• Standard finishes: ZN, GRN • Standard finishes: ZN, GRN
• Wt./C 288 Lbs. (130.6 kg)
• Wt./C 97 Lbs. (44.0 kg)
• Standard finishes: ZN, GRN
• Wt./C 550 Lbs. (249.5 kg)
31/2”
(88.9)
7/16” (11.1)
Dia. 4
Holes
4”
15/8”
(101.6)
(41.3)
1/4”
3/4”
3/8” (9.5)
Countersunk
To
3/4” (19.0)
Dia.
(19.0)
31/2”
13/4”
(88.9)
(44.4)
(6.3)
9/16”
6”
(152.4)
(127.0)
6”
(152.4)
3”
(14.3)
5”
5”
(127.0)
3/4” (19.0)
(76.2)
15/8”
31/2”
7”
31/16”
21/16”
(177.8)
(77.8)
(52.4)
(41.3)
(88.9)
Dia. 4 Holes
B187 Bracket
B188 Bracket
•
•
•
•
•
•
•
•
•
•
Uniform Loading 1450 Lbs. (6.45 kN)
Safety Factor of 2.5
Hole Spacing on Bracket Top 55/16” (150.8) Center to Center
Standard finishes: ZN, GRN
Wt./C 193 Lbs. (87.5 kg)
Uniform Loading 1080 Lbs. (4.80 kN)
Safety Factor of 2.5
Hole Spacing on Bracket Top 815/16” (227.0) Center to Center
Standard finishes: ZN, GRN
Wt./C 241 Lbs. (109.3 kg)
11/16”
21/4”
11/16”
(27.0)
(57.1)
(27.0)
21/4”
(57.1)
4”
9”
(101.6)
(228.6)
4”
(101.6)
12”
Strut Fittings
(304.8)
B189 Bracket
B541 Bracket
•
•
•
•
•
•
•
•
•
•
Uniform Loading 870 Lbs. (3.87 kN)
Safety Factor of 2.5
Hole Spacing on Bracket Top 1115/16” (303.2) Center to Center
Standard finishes: ZN, GRN
Wt./C 308 Lbs. (139.7 kg)
11/16”
(27.0)
Uniform Loading 1240 Lbs. (5.51 kN)
Safety Factor of 2.5
Hole Spacing on Bracket Top 77/16” (188.9) Center to Center
Standard finishes: ZN, GRN
Wt./C 201 Lbs. (91.2 kg)
21/4”
11/16”
21/4”
(57.1)
(27.0)
(57.1)
4”
4”
(101.6)
(101.6)
101/2”
(266.7)
15”
(381.0)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
99
Strut Systems
Brackets
B190 12” (304.8) Bracket
B191-18 18” (457.2) Bracket
•
•
•
•
•
•
•
•
Uniform Loading 900 Lbs. (4.00 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 260 Lbs. (117.9 kg)
Uniform Loading 600 Lbs. (2.67 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 377 Lbs. (171.0 kg)
11/16”
(27.0)
11/16”
(27.0)
9/16”
x 3” Slot
4”
(14.3) (76.2)
4”
(101.6)
18”
12”
(101.6)
(457.2)
(304.8)
71/2”
71/2”
(190.5)
(190.5)
9/16”
2”
x 3” Slot
(14.3) (76.2)
(50.8)
2”
(50.8)
B289-12 121/2” (317.5) Bracket
•
•
•
•
B191-24 24” (609.6) Bracket
Uniform Loading 1040 Lbs. (4.63 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 285 Lbs. (129.3 kg)
•
•
•
•
11/16”
(27.0)
13/16”
4”
(30.1)
(101.6)
13/16”
Uniform Loading 450 Lbs. (2.00 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 377 Lbs. (171.0 kg)
(30.1)
31/4”
6”
(82.8)
(152.4)
24”
121/2”
31/8”
(79.4)
(609.6)
(317.5)
33/4”
(95.2)
71/2”
(190.5)
13/16”
21/2”
9/16”
(30.1)
x 3” Slot
(14.3) (76.2)
(63.5)
2”
(50.8)
B290 161/2” (419.1) Bracket
•
•
•
•
B192 24” (609.6) Bracket
11/16”
Uniform Loading 1200 Lbs. (5.34 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 405 Lbs. (183.7 kg)
13/16”
(30.1)
(30.1)
Uniform Loading 820 Lbs. (3.65 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 576 Lbs. (261.3 kg)
6”
Strut Fittings
13/16”
•
•
•
•
(27.0)
(152.4)
6”
51/4”
(152.4)
(133.3)
24”
31/8”
(609.6)
161/2”
(419.1)
(79.4)
12”
53/4”
27/16”
(146.0)
(61.9)
21/2”
(63.5)
(304.8)
9/16”
x 3” Slot
(14.3) (76.2)
13/16”
2”
(30.1)
(50.8)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
100
Brackets
B289-14 141/2” (368.3) Bracket
B291 181/2” (469.9) Bracket
•
•
•
•
•
•
•
•
Uniform Loading 900 Lbs. (4.00 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 295 Lbs. (133.8 kg)
13/16”
13/16”
(30.1)
Uniform Loading 1070 Lbs. (4.76 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN
Wt./C 468 Lbs. (212.3 kg)
13/16”
(30.1)
13/16”
(30.1)
(30.1)
31/4”
(82.8)
6”
31/8”
(152.4)
(79.4)
141/2”
6”
51/4”
(152.4)
(133.3)
(368.3)
31/8”
181/2”
(79.4)
(469.9)
53/4”
73/4”
(146.0)
(196.8)
21/2”
21/2”
(63.5)
13/16”
(63.5)
(30.1)
13/16”
(30.1)
B292 201/2” (520.7) Bracket
•
•
•
•
B409
Single Channel Bracket
Uniform Loading 600 Lbs. (2.67 kN)
Safety Factor of 2.5
Standard finishes: ZN, GRN, HDG, SS4
Wt./C 490 Lbs. (222.2 kg)
• Safety Factor of 2.5
• Standard finishes: ZN, GRN, SS4
13/16”
(20.6)
2”
45/8”
(117.5)
13/16”
(30.1)
(50.8)
13/16”
A
(30.1)
6”
(152.4)
71/4”
(184.1)
201/2”
31/8” (520.7)
3”
Strut Fittings
73/4”
21/2”
B22
(76.2)
(79.4)
Part
No.
B409-6
B409-9
B409-12
B409-14
B409-16
B409-18
B409-24
(196.8)
(63.5)
13/16”
(30.1)
A
Uniform Load
In.
mm
Lbs.
kN
6”
9”
12”
14”
16”
18”
24”
(152.4)
(228.6)
(304.8)
(355.6)
(406.4)
(457.2)
(609.6)
1920
1280
960
800
(8.54)
(5.69)
(4.27)
(3.56)
(3.25)
(2.84)
(2.13)
730
640
480
Wt./C
Lbs.
kg
152 (68.9)
195 (88.4)
232 (105.2)
274 (124.3)
314
(142.4)
347 (157.4)
450 (204.1)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
101
Strut Systems
Brackets
B297
Double Channel Bracket
• Safety Factor of 2.5
• Standard finishes:
ZN, GRN, HDG
13/16”
2”
(20.6)
(50.8)
3/8”
61/4”
(9.5)
(158.7)
Part
No.
B297-12
B297-18
B297-24
B297-30
B297-36
B297-42
A
Uniform Load
Wt./C
A
In.
mm
Lbs.
kN
Lbs.
kg
12”
18”
24”
30”
36”
42”
(304.8)
(457.2)
(609.6)
(762.0)
(914.4)
(1066.8)
1660
1100
835
665
550
465
(7.37)
(4.88)
(3.71)
(2.95)
(2.44)
(2.06)
485
668
857
1040
1240
1440
(220.0)
(303.0)
(388.7)
(471.7)
(562.4)
(653.2)
45/8”
(117.5)
B22A
B494
Braced Single Bracket
• Safety Factor of 2.5
• Standard finishes:
ZN, GRN
11/2”
(38.1)
13/16”
(20.6)
H
Part
No.
B494-12
B494-18
B494-24
B494-30
B494-36
B494-42
B494-48
L
In.
H
mm
In.
12” (304.8)
18” (475.2)
24” (609.6)
30” (762.0)
36” (914.4)
42” (1066.8)
48” (1219.2)
Uniform Load
mm
83/4” (222.2)
83/4” (222.2)
83/4” (222.2)
111/4” (285.7)
111/4” (285.7)
16” (406.4)
16” (406.4)
Lbs.
kN
Lbs.
kg
1580
1000
996
924
864
580
500
(7.02)
(4.45)
(4.43)
(4.11)
(3.84)
(2.58)
(2.22)
364
479
716
927
1095
1400
1510
(165.1)
(217.3)
(324.8)
(420.5)
(496.7)
(635.0)
(684.9)
L
15/8”
Wt. /C
(41.3)
4”
(101.6)
Inside Brace on
B494-24 and Larger.
B42
B174SH-B186SH L&R Slotted Bracket
•
•
•
•
Safety Factor of 2.5
Specify L for left or R for right bracing
Material: ASTM A1011 33,000 PSI min. yield
Standard finishes: ZN, GRN
2”
9/32” (7.1)
(50.8)
Dia. Holes
A
Part
No.
In.
24”
26”
28”
30”
12”
14”
16”
18”
20”
22”
6”
8”
10”
B
mm
(609.6)
(660.4)
(711.2)
(762.0)
(304.8)
(355.6)
(406.4)
(457.2)
(508.0)
(558.8)
(152.4)
(203.2)
(254.0)
In.
Uniform Load
mm
67/16” (163.5)
615/16” (176.2)
77/16” (188.9)
715/16” (201.6)
37/16” (87.3)
315/16” (100.0)
47/16” (112.7)
415/16” (125.4)
57/16” (138.1)
515/16” (150.8)
115/16” (49.2)
27/16” (61.9)
215/16” (74.6)
Wt./C
Lbs.
kN
Lbs.
kg
225
225
225
225
350
350
250
250
250
250
225
225
325
(1.00)
(1.00)
(1.00)
(1.00)
(1.55)
(1.55)
(1.11)
(1.11)
(1.11)
(1.11)
(1.00)
(1.00)
(1.44)
370
425
480
520
143
162
204
232
275
317
58
82
103
(167.8)
(192.8)
(217.7)
(235.9)
(64.8)
(73.5)
(92.5)
(105.2)
(124.7)
(143.8)
(26.3)
(37.2)
(46.7)
B
13/32”
102
1”
(25.4)
(10.3) (25.4)
Right bracket shown, left bracket
gussett on opposite side.
4Dimension compatible fitting
Strut Systems
2”
(50.8)
Mounting Hole
7/16” (11.1) Dia.
Reference page 73 for general fitting and standard finish specifications.
x 1”
Slot
Strut Fittings
B174SH
B175SH
B176SH
B177SH
B178SH
B179SH
B180SH
B181SH
B182SH
B183SH
B184SH
B185SH
B186SH
A
Brackets
B196
Channel
Clevis Bracket
B198
Channel Clevis Bracket
13/16”
(20.6)
• Safety Factor of 2.5
• Standard finishes:
ZN, GRN
• Safety Factor of 2.5
53/8”
• Standard finishes:
(136.5)
ZN, GRN
13/16”
(20.6)
31/2”
(88.9)
A
35/8”
A
(92.1)
B22
Part
No.
B196-18
B196-24
A
In.
Uniform Load
mm
Lbs.
18” (457.2)
24” (609.6)
kN
600 (2.67)
450 (2.00)
B22
Wt./C
Lbs.
430 (195.0)
510 (231.3)
B198A
Channel Clevis Bracket
• Safety Factor of 2.5
• Standard finishes:
ZN, GRN
Part
No.
kg
B198-6
B198-12
A
In.
mm
6” (152.4)
12” (304.8)
Uniform Load
Lbs.
• Safety Factor of 2.5
• Standard finishes:
ZN, GRN
(20.6)
Wt./C
Lbs.
1600 (7.12)
800 (3.56)
kg
185 (83.9)
284 (128.8)
13/16”
B293
Channel Bracket
13/16”
kN
(20.6)
31/2”
11/2”
(88.9)
(38.1)
31/2”
A
(88.9)
A
B22
Part
No.
B22
Part
No.
B198A-6
B198A-12
A
In.
mm
6” (152.4)
12” (304.8)
B293A
Channel Bracket
• Safety Factor of 2.5
• Standard finishes:
ZN, GRN
Uniform Load
Lbs.
kN
1600 (7.12)
800 (3.56)
Wt./C
Lbs.
kg
185 (83.9)
284 (128.8)
Uniform Load
Wt./C
mm
Lbs.
kN
Lbs.
6”
12”
18”
24”
(152.4)
1200
600
400
300
(5.34)
144
252
340
412
(304.8)
(457.2)
(609.6)
(2.67)
(1.78)
(1.33)
kg
(65.3)
(114.3)
(154.2)
(186.9)
B194 Bracket for B22 & B24
13/16”
(20.6)
11/2”
31/2”
(38.1)
(88.9)
A
Strut Fittings
B293-6
B293-12
B293-18
B293-24
A
In.
• Safety Factor of 2.5
• 6300 In.-Lbs (712 N•m) applies to fitting only,
not to strength of strut arm
• Refer to pages 23 & 24 for
13/32”
strut loading data
(27.8)
• Standard finishes: ZN, GRN
• Wt./C 210 Lbs. (95.2 kg)
B22
63/8”
B22
A
Part
No.
In.
mm
Lbs.
kN
Lbs.
B293A-6
B293A-12
B293A-18
B293A-24
6”
12”
18”
24”
(152.4)
1200
600
400
300
(5.34)
144
252
340
412
(304.8)
(457.2)
(609.6)
Uniform Load
(161.9)
(2.67)
(1.78)
(1.33)
Wt./C
kg
(65.3)
23/16”
(114.3)
(55.6)
(154.2)
33/4”
(186.9)
(95.2)
B22
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
103
Strut Systems
Brackets
B370
Bracket for B22A & B11
B195
• Safety Factor of 2.5
13/32”
• 13000 In.-Lbs (1469 N•m) applies
(27.8)
to fitting only, not to strength of
strut arm
• Refer to pages 23 & 24 for
strut loading data
• Standard finishes: ZN, GRN
• Wt./C 266 Lbs. (120.6 kg)
8”
B22
(203.2)
Bracket for B42
• Safety Factor of 2.5
• 2500 In.-Lbs (282 N•m) applies
to fitting only, not to strength
of strut arm
21/8”
• Refer to pages 23, 24 & 32
(54.0)
for strut loading data
• Standard finishes: ZN, GRN
• Wt./C 174 Lbs. (78.9 kg)
37/8”
B22
(98.4)
315/16”
B22A
(100.0)
B42
33/4”
33/4”
(95.2)
(95.2)
B440
Bracket for B52 & B54
B449-4, 8 & 12
Cable Saddle Bracket
• Safety Factor of 2.5
• 2000 In.-Lbs (226 N•m) applies to fitting only,
not to strength of strut arm
• Refer to page 23, 24 & 34 for
strut loading data
B22
1
• Standard finishes: ZN, GRN 2 /8”
(54.0)
• Wt./C 177 Lbs. (80.3 kg)
• Safety Factor of 2.5
• Material: 11 Gauge (3.0)
ASTM A1011 HSLAS Gr. 50
• Standard finishes: ZN, GRN
13/16”
37/8”
(20.6)
(98.4)
B
B52
A
33/4”
(95.2)
B449-18
18” (457.2) Cable Saddle Bracket
•
•
•
•
•
2”
Safety Factor of 2.5
Uniform Load 960 Lbs. (4.17 kN)
Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50
Standard finishes: ZN, GRN
Wt./C 312 Lbs. (141.5 kg)
(50.8)
(20.6)
2”
(50.8)
4”
(101.6)
18”
(457.2)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
104
Wt./C
Lbs.
kg
74 (33.5)
124 (56.2)
184 (83.4)
Strut Fittings
Part
A
B
Uniform Load
In.
mm
In.
mm
Lbs.
kN
No.
B449-4 41/2” (114.3) 23/8” (60.3) 2400 (10.67)
B449-8 81/2” (215.9) 23/8” (60.3) 1270 (5.65)
B449-12 121/2”(317.5) 4” (101.6) 860 (3.82)
13/16”
Brackets
B816
B852S-*-**
• Standard finishes: ZN, HDG
• *Specify Width: W = 8, 12, 16
• **Specify Depth: D = 6, 8, 10, 12, 16, 18, 24
• 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band
• Standard finishes: ZN, HDG
2”
13/32” (10.3)
(50.8)
61/2”
13/16” (20.6)
23/8”
(165.1)
Dia.
Dia.
(60.3)
21/8”
(54.0)
9/16”
(14.3)
14”
14”
(355.6)
(355.6)
9/16”
(14.3)
725/32”
(197.6)
x 29/16” Slot
(65.1)
11/16”
x 1” Slot
(17.4)
(25.4)
W
D
13/16”
x 1” Slot
(20.6)
(25.4)
B802D-*
B810-*
• *Specify Width: W = 8, 12, 16
• Standard finishes: ZN, HDG
• *Specify Width: W = 8, 12, 16
• 13/16” (20.6mm) x 1” (25.6mm) banding slots for steel band
• Standard finishes: ZN, HDG
13/16” (20.6)
Dia.
13/32” (10.3)
Dia.
Strut Fittings
13/16” (20.6)
Dia.
95/8”
(244.5)
W
725/32”
(197.6)
W
13/16”
x 1” Slot
(20.6)
(25.4)
Reference page 73 for general fitting and standard finish specifications.
105
Strut Systems
Brackets
B811-*
B812-*
• *Specify Width: W = 8, 12, 16
• Can be attached directly to B809 & B812
• Standard finishes: ZN, HDG
• *Specify Depth: D = 6, 8, 10, 12, 16, 18, 24
• 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band
• Standard finishes: ZN, HDG
121/32”
(42.1)
13/32” (10.3)
Dia.
13/16” (20.6)
W
27/16”
Dia.
725/32”
(61.9)
(197.6)
D
13/16”
13/16”
x 1” Slot
(20.6)
(25.4)
(20.6)
B809B-*
• *Specify Depth: D = 6, 8, 10, 12, 16, 18, 24
• 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band
• Standard finishes: ZN, HDG
13/32” (10.3)
Dia.
13/16” (20.6)
Dia.
D
Part No.
D
In.
6”
In.
(152.4)
725/32”
mm
8” (203.2)
10” (254.0)
143/4” (374.7)
163/4” (425.5)
B809B-12
12” (304.8)
183/4” (476.2)
B809B-16
16” (406.4)
223/4” (577.8)
B809B-18
B809B-24
18” (457.2)
24” (609.6)
243/4” (628.6)
273/4” (704.8)
B809B-8
B809B-10
(197.6)
123/4” (323.9)
H
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
106
13/16”
x 1” Slot
(20.6)
(25.4)
Strut Fittings
B809B-6
H
mm
Miscellaneous Fittings
B214 R&L
Reel Rack Support for 11/4” (32) Pipe
B514 R&L
Reel Rack Support for 2” (50) Pipe
• Standard finishes: ZN, GRN
• Wt./C 200 Lbs. (90.7 kg)
• Standard finishes: ZN, GRN
• Wt./C 246 Lbs. (111.6 kg)
3”
3”
(76.2)
(76.2)
53/8”
53/8”
(136.5)
(136.5)
A
B214R
Right Hand
B214L
Left Hand
35/8”
35/8”
(92.1)
(92.1)
53/8”
53/8”
(136.5)
(136.5)
B514R
Right Hand
B475
Double Reel Rack Support on
Single Channel for 11/4” (32) Pipe
B473
Double Reel Rack Support on
Single Channel for 2” (50) Pipe
• Standard finishes: ZN, GRN
• Wt./C 326 Lbs. (147.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 351 Lbs. (159.2 kg)
3”
B514L
Left Hand
3”
(76.2)
(76.2)
9”
9”
(228.6)
(228.6)
B474
Double Reel Rack Support on
Double Channel for 11/4” (32) Pipe
B472
Double Reel Rack Support on
Double Channel for 2” (50) Pipe
• Standard finishes: ZN, GRN
• Wt./C 257 Lbs. (116.6 kg)
• Standard finishes: ZN, GRN
• Wt./C 299 Lbs. (135.6 kg)
31/4”
31/4”
(82.8)
Strut Fittings
(82.8)
53/8”
53/8”
(136.5)
(136.5)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
107
Strut Systems
Miscellaneous Fittings
B438
Pipe Support Bracket
B439
Pipe Support Bracket
• Standard finishes: ZN, GRN
• Material: ASTM A36
• Wt./C 132 Lbs. (59.9 kg)
• Standard finishes: ZN, GRN
• Wt./C 88 Lbs. (39.9 kg)
41/4”
(107.9)
31/2”
(88.9)
3/8”
4”
1/4”
(9.5)
4”
(101.6)
(6.3)
(101.6)
B411 Series
Ladder Rungs
B381-B385
Wall Ladder Brackets
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
13/16”
(20.6)
C
B
2” I.D.
A
(50.8)
13/16”
(20.6)
A
13/16”
(20.6)
Part
No.
B411-12
B411-15
B411-18
Part
No.
A
In.
Wt./C
mm
12” (304.8)
15” (381.0)
18” (457.2)
Lbs.
B381
B382
B383
B384
B385
kg
176 (79.8)
202 (91.6)
234 (106.1)
A
In.
23/8”
43/8”
63/8”
83/8”
103/8”
B
mm
(60.3)
(111.1)
(161.9)
(212.7)
(263.5)
In.
6”
8”
10”
12”
14”
mm
C
In.
Wt./C
mm
75/8” (193.7)
95/8” (244.5)
(152.4)
(203.2)
(254.0) 115/8” (295.3)
(304.8) 135/8” (346.1)
(355.6) 155/8” (396.9)
Lbs.
kg
110
164
200
253
318
(49.9)
(74.4)
(90.7)
(114.7)
(144.2)
B587-1/2, 3/4 & 1
Pipe Coupling Fitting
• Safety Factor of 2.5
• Standard finishes: ZN, GRN
B587-1/2
B587-3/4
B587-1
211/16”
53/8”
(68.2)
(136.5)
For
Pipe Size
Wt./C
In.
mm
Lbs.
1/2”
(15)
(20)
(25)
77 (34.9)
84 (38.1)
105 (47.6)
3/4”
1”
kg
Strut Fittings
Part
No.
Design Load
Design
Load
Lbs.
kN
1000 (4.45)
1400 (6.23)
1900 (8.45)
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
108
Miscellaneous Fittings
B349
Trolley Beam Support
B350
Trolley Beam Joint Support
• Design Load 1200 Lbs. (5.34 kN)
• Safety Factor of 2.5
• Use 3/8” x 3” bolts in side hole to clamp
strut together (not included)
• Standard finishes: ZN, GRN
9/16”(14.3) Dia.
• Wt./C 107 Lbs. (48.5 kg)
1 Hole
• Design Load 1200 Lbs. (5.34 kN)
21/8”
• Use 3/8” x 3” bolts in side hole to clamp
(54.0)
strut together (not included)
• Standard finishes: ZN, GRN 9
/16”(14.3) Dia.
• Wt./C 233 Lbs. (105.7 kg)
1 Hole
315/16”
31/2”
(100.0)
21/8”
(54.0)
315/16”
(100.0)
(88.9)
7/16”(11.1)
11/32”
Dia.
11/32”
2 Holes
(26.2)
7/16”(11.1) Dia.
2 Holes
(26.2)
13/32”
15/8”
121/32”
(41.3)
121/32”
(42.0)
(42.0)
21/32” (27.8)
(16.7)
B614
Column Support for B22
B613
Column Support for B22
B613A
Column Support for B52
• Quick installation (one bolt to tighten)
• Design Load 800 Lbs. (3.56 kN) Slip
with Safety Factor of 3
• Use with B22 and B24 Channel
• Sold in pairs
• Standard finish: ZN
• Wt./C 50 Lbs. (22.6 kg)
• Design Load 800 Lbs. (3.56 kN) Slip
with Safety Factor of 3
• Use with B22 and B24 Channel
• Setscrews to be torqued to 19 ft./Lbs
• Sold in pairs
• Standard finishes: ZN, GRN, HDG
• Wt./C 100 Lbs. (45.3 kg)
15/8”
• Design Load 800 Lbs. (3.56 kN) Slip
with Safety Factor of 3
• Use with B52 and B54 Channel
• Setscrews to be torqued to 19 ft./Lbs
• Sold in pairs
• Standard finishes: ZN, GRN, HDG
• Wt./C 100 Lbs. (45.3 kg)
15/8”
(41.3)
(41.3)
31/2”
31/2”
(88.9)
3/8” x 2”
Cone Point
Setscrews
3/8” x 2”
Cone Point
Setscrews
B560
45° Stair Support
B562
371/2° Stair Support
• Standard finishes: ZN, GRN
• Wt./C 220 Lbs. (99.8 kg)
• Standard finishes: ZN, GRN
• Wt./C 206 Lbs. (93.4 kg)
87/8”
87/8”
(225.4)
(225.4)
Strut Fittings
(88.9)
31/2”
31/2”
(88.9)
11/16”
31/2”
(27.0)
31/2”
17/8”
(88.9)
(47.6)
13/16”
13/16”
(88.9)
11/16”
(27.0)
17/8”
(88.9)
(47.6)
(20.6)
(20.6)
45°
371/2°
33/4”
33/4”
(95.2)
(95.2)
Reference page 73 for general fitting and standard finish specifications.
109
Strut Systems
Miscellaneous Fittings
B376
Four Bearing Trolley
Assembly
35/16”
B377
Two Bearing Trolley Assembly
15/16”
(84.1)
(33.3)
• Safety Factor of 2.5
• Stainless steel ball bearings
• Not for continuous cycling
Bearing O.D.
applications
13/16”
• Standard finishes: ZN
• Wt./C 48 Lbs. (21.8 kg)
(20.6)
• Safety Factor of 2.5
• Stainless steel ball bearings
• Not for continuous cycling
applications
• Standard finishes: ZN 33/8”
• Wt./C 110 Lbs. (49.9 kg) (85.8)
11/8” (28.6)
15/16”
3”
(23.5)
(76.2)
Lbs.
kN
RPM
300
450
600
(1.33)
@600
@300
@100
Design Load
Lbs.
kN
RPM
150
225
437
(.67)
@600
@300
@100
(1.00)
(1.94)
B477
Two Bearing Light Duty
Trolley Assembly
33/8”
13/16”
(85.8)
(20.6)
11/4”
(31.7)
Design Load
B478
Four Bearing Light Duty
Trolley Assembly
•
•
•
•
•
Design Load 50 Lbs. (.22 kN)
Safety Factor of 2.5
Stainless steel ball bearings
Not for continuous cycling applications
Material:12 Gauge (2.6) ASTM A1011
33,000 PSI min. yield
• Standard finishes: ZN
• Wt./C 30 Lbs. (13.6 kg)
•
•
•
•
•
Design Load 100 Lbs. (.44 kN)
Safety Factor of 2.5
Stainless steel ball bearings
Not for continuous cycling applications
Material:12 Gauge (2.6) ASTM A1011
33,000 PSI min. yield
• Standard finishes: ZN
• Wt./C 68 Lbs. (30.8 kg)
11/4”
(31.7)
11/8”
13/4”
(28.6)
(44.4)
B477P
With Plastic
Bearings
11/32”
5/8”
• Design Load
10 Lbs. (.045 kN)
(8.7)
9/32” (7.1)
B478P
With Plastic
Bearings
• Design Load
20 Lbs. (.090 kN)
(15.9)
9/32”
Dia. Hole
9/32” (7.1)
Dia. Hole
x 9/16” Slot-(2)
(7.1)
(14.3)
3/4”
3/4”
(19.0)
11/8” (28.6)
Bearing O.D.
Design Load in B22
Design Load in B22
(2.67)
(33.3)
5/8”
(15.9)
(2.00)
15/16”
11/4”
3”
(19.0)
(31.7)
(76.2)
2”
(50.8)
Design Load
Design Load
B478H
Four Bearing Light Duty
Trolley Assembly with Eye Hook
B477H
Two Bearing Light Duty
Trolley Assembly with Eye Hook
•
•
•
•
•
•
•
•
•
•
11/4”
(31.7)
11/8”
Design Load 100 Lbs. (.44 kN)
Safety Factor of 2.5
Stainless steel ball bearings
Not for continuous cycling applications
Material:12 Gauge (2.6) ASTM A1011
33,000 PSI min. yield
• Standard finishes: ZN
• Wt./C 72 Lbs. (32.6 kg)
(28.6)
B477HP
With Plastic
Bearings
B478HP
With Plastic
Bearings
315/16”
• Design Load
10 Lbs. (.045 kN)
(100.0)
11/32”
1/4” (6.3)
(8.7)
Eye Rod
3/4”
(19.0)
• Design Load
20 Lbs. (.090 kN)
3/4”
I.D
Eye Rod
I.D
(19.0)
Design Load
Design Load
4Dimension compatible fitting
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
1/4” (6.3)
110
Strut Fittings
Design Load 50 Lbs. (.22 kN)
Safety Factor of 2.5
Stainless steel ball bearings
Not for continuous cycling applications
Material:12 Gauge (2.6) ASTM A1011
33,000 PSI min. yield
• Standard finishes: ZN
• Wt./C 36 Lbs. (16.3 kg)
Miscellaneous Fittings
B203-B206 & B220-B223
Channel End Caps Type X
A
• Material: ASTM A1011 CS Type B
• Standard finishes: ZN, GRN, HDG, SS4, AL
Part
No.
Use
With
In.
A
mm
Lbs.
kg
B203
B204
B205
B206
B220
B221
B222
B223
B42
B54
B22
B32
B52
B12
B11
B24
1.015
.827
1.640
1.390
.827
2.452
3.265
1.640
(25.8)
(21.0)
(41.6)
(35.3)
(21.0)
(62.3)
(82.9)
(41.6)
6
5
10
8
4
15
20
10
(2.7)
(2.2)
(4.5)
(3.6)
(1.8)
(6.8)
(9.1)
(4.5)
B283-B286
Channel End Caps
• Material: ASTM A1011 33,000 PSI min. yield
• Standard finishes: ZN, GRN
Wt./C
A
B
Part
No.
Use With
In.
A
mm
B
B283
B284
B285
B286
B52
B54 & B56
B22
B24 & B26
119/32”
119/32”
119/32”
119/32”
(40.5)
In.
Wt./C
mm
25/32” (19.8)
25/32” (19.8)
(40.5)
(40.5) 119/32”(40.5)
(40.5) 119/32”(40.5)
B287 & B288
Channel End Caps
B3322, B3332, B3342, B3352
Anchor End Caps Type Y
• Material: ASTM A1011 33,000 PSI min. yield
• Standard finishes: ZN, GRN
• Material: ASTM A1011 33,000 PSI min. yield
• Standard finishes: ZN
Lbs.
kg
6
6
13
14
(2.7)
(2.7)
(5.9)
(6.3)
3/8” (9.5)
Dia. Hole
119/32”
119/32”
(40.5)
(40.5)
A
113/16”
Part
No.
Use
With
Wt./C
Lbs.
kg
B287
B288
B22
B24
13
14
(5.9)
B3322
B3332
B3342
B3352
(6.3)
(66.7)
B
(46.0)
Part
No.
25/8”
A
Use With
B22I
B32I
B42I
B52I
B
In.
1.270
1.000
.645
.460
mm
(32.2)
(25.4)
(16.4)
(11.7)
In.
Wt./C
mm
13/16” (30.2)
13/16” (30.2)
11/4” (31.8)
15/16” (33.3)
Lbs.
kg
15
15
15
15
(6.8)
(6.8)
(6.8)
(6.8)
B822A
Plastic End Cap for B22A & B11
B852
Plastic End Cap for B52
• Material: Soft White PVC
• Wt./C 3 Lbs. (1.3 kg)
• Available in colors: White (W),
Yellow (Y), Black (BLK), Gray (GRY),
Green (GRN)
• Material: Soft White PVC
• Wt./C 5 Lbs. (2.2 kg)
• Available in colors: White (W),
Yellow (Y), Black (BLK), Gray (GRY),
Green (GRN)
• Material: Soft White PVC
• Wt./C 2.5 Lbs. (1.1 kg)
• Available in colors: White (W),
Yellow (Y), Black (BLK), Gray (GRY),
Green (GRN)
Strut Fittings
B822
Plastic End Cap for B22 & B24
11/4”
(31.7)
11/4”
11/4”
(31.7)
(31.7)
Reference page 73 for general fitting and standard finish specifications.
111
Strut Systems
Miscellaneous Fittings
B823
Profile End Caps
B825
Plastic End Caps
• Material: PVC
• Available in colors: White (W),
Yellow (Y), Black (BLK), Gray (GRY),
Green (GRN)
• Material: Polyurethane
• Available in colors: Gray (GRY), Green (GRN)
Approx. 3/4” deep
(19.0)
Part No.
Fits
Channel Sizes
Lbs.
Wt./C
kg
B823-22A
B823-22
B823-42
B823-52
B22A, B24A, B26A
B22, B24, B26
B42
B52, B54, B56
6.9
4.1
3.8
3.5
(3.1)
(1.8)
(1.7)
(1.6)
Part No.
Fits
Channel Sizes
Lbs.
kg
B22 & B24
B52 & B54
2.0
1.0
(0.9)
(0.4)
B825-22
B825-52
B408SLBVNS Series
Stand-Off Brackets
43/8”
(111.1)
• Material: 1/4” (6.3)
• Standard Finishes: HDG, ZN, GRN
• For pipe or rigid conduit sizes
of 11/2” (40) and 2” (50) use with
B501 Series ‘U’-Bolts (see page 53)
• For strut channels 15/8” (41.3) wide
use with B500 Series Square ‘U’-Bolts
(see page 53)
• Hardware is not included
Wt./C
21/8”
(53.5)
A
11/8”
(28.6)
45/8”
15/16”
(117.5)
(33.3)
21/4”
1/2”
(57.1)
(12.7)
23/16”
(55.6)
Part
No.
B408SLBVNS
B408SLBVNS1
B408SLBVNS2
A
In. (mm)
31/2” (88.9)
3” (76.2)
2” (50.8)
(27.0)
Wt./C
Lbs.
23/16”
kg
189 (85.7)
220 (99.8)
236 (107.0)
11/16”
(55.6)
(6) Slots
7/16” (11.1) x 11/8” (28.6)
11/16”
21/4”
(27.0)
(57.1)
Strut Fittings
Reference page 73 for general fitting and standard finish specifications.
Strut Systems
112