Fasteners
FIS-164
Instruction sheet
KwikWire™ accessories
This bulletin contains instructions for the selection, installation, and use of the KwikWire accessory
products shown in the single, double, and triple hanger configurations. Read all instructions completely
before proceeding to become familiar with the procedure and the parts being used.
KwikWire Accessories Working Loads
KwikWire Rope Data
Accessory
Part No.
Wire Rope
Diameter
Lbs. Safety
Factor 5
Catalog
No.
Construction
Wire Rope
Diameter
BKA-063-XXX
1/16"
0-30
BKW063
7x7
1/16"
BKL-063-XXX
1/16"
0-75
BKW094
7x7
3/32"
BKL-094-XXX
3/32"
25-150
BKT-063-XXX
1/16"
0-75
BKYTXX-063-XXX
1/16"
0-75
BK3TXX-063-XXX
1/16"
0-75
Clamp
Part No.
Wire Rope
Diameter
Lbs. Safety
Factory 5
BKH-094-XXX
3/32"
25-150
BKC100
1/16"
0-75
BKYHXX-094-XXX
3/32"
25-150
BKC100
3/32"
25-150
BK3HXX-094-XXX
3/32"
25-150
BKYWXX-063-XXX
1/16"
0-75
BK3WXX-063-XXX
1/16"
0-75
BKYWXX-094-XXX
3/32"
25-150
BK3WXX-094-XXX
3/32"
25-150
BKBYY-063-XXX
1/16"
0-75
BKYBYY-XX-063-XXX
1/16"
0-75
BK3BYY-XX-063-XXX
1/16"
0-75
BKBZZ-094-XXX
3/32"
25-150
BKYBZZ-XX-094-XXX
3/32"
25-150
BK3BZZ-XX-094-XXX
3/32"
25-150
KwikWire Clamp Working Loads*
7x7
* Working loads shown at left are
for hanging vertically.
For suspending at 15°, 30°,
45° or 60° angles form vertical
use the following percentage of
the working loads from the
chart:
15° = 96%
30° = 86%
45° = 70%
60° = 50%
Recommendations:
•
•
•
•
•
•
•
•
Do not exceed the safe working load of the product shown in chart
Do not use for overhead lifting and hoisting
Do not paint cable near working area of KwikWire clamp connector
Do not apply lubricant
For use in "DRY LOCATIONS ONLY"
Only use to support stationary loads
Do not splice wire together using KwikWire clamps
Only for permanent installations. Do not re-use.
Note:
• "XX" = leg length, e.g. "12", "18", or "30"
• "YY" = bolt size, e.g. "25" (1/4" bolt) or "M6"
• "ZZ" = bolt size, e.g. "38" (3/8" bolt) or "M8", "M10"
• "XXX" = straight length, e.g. "40", "80", "120", "180", "240", or "360"
• Catalog number suffix "-XXX" may be omitted to designate a loop size
• Catalog number may be followed by "K" to designate a kit
Single KwikWire
Hanger Accessory
Configurations
Notes:
Maximum rod size for hooks: 3/8" diameter
Maximum hole size for toggles: 0.47" diameter
BKH
BKT
BKB
BKL
BKA
Double KwikWire™ Hanger
Accessory Configurations
Notes:
The angle between each of multi leg
and gravity line should not exceed 30°
(for double and triple configurations).
30°
Max.
30°
Max.
Maximum rod size for hooks: 3/8" diameter
Maximum hole size for toggles: 0.47" diameter
BKYH
BKYT
BKYB
Triple KwikWire Hanger
Accessory Configurations
30°
Max.
30°
Max.
Notes:
The angle between each of multi leg
and gravity line should not exceed 30°
(for double and triple configurations).
Maximum rod size for hooks: 3/8" diameter
Maximum hole size for toggles: 0.47" diameter
BK3H
BK3T
BK3B
KwikWire™ is a trademark of Eaton’s B-Line Business
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
© 2014 Eaton
All Rights Reserved
Printed in USA
Publication No. FIS-164
November 2014
Eaton’s B-Line Business
509 West Monroe Street
Highland, IL 62249
United States
Phone: 800-851-7415
www.cooperbline.com/kwikwire
Eaton is a registered trademark.
All other trademarks are property
of their respective owners.