7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
WESTGATE ELEMENTARY SCHOOL REPLACEMENT
2514 W. 4th Ave.
Kennewick, WA 99336
ADDENDUM No. 2
March 28, 2016
GENERAL INFORMATION
ITEM
1
DETAIL/DESCRIPTION
NOTE: The Sign-in Sheet for the Pre-bid Meeting (3-24-16) is also available on Kennewick
School District’s website: http://www.ksd.org/District/Departments/Capital-Projects.
NOTE: The site survey (available for download on the Owner's website) does not show
stockpiled material. Crushed brick, crushed asphalt and general fill quantities and approximate
locations are shown on sheet C1.00.
ELECTRICAL NOTE: All exposed cable located above the suspended acoustical tile ceilings
shall be plenum rated. Cable installed in conduit can be non-plenum
ELECTRICAL NOTE: All door position contact switches are provided with the hardware.
Division 26 shall provide rough-in to door frame. Coordinate RI location (into frame) with the
hardware installer
ELECTRICAL NOTE: Provide cable and rough-in from all doors with electronic hardware and
magnetic holders to the security access control system. All doors with electronic hardware shall
lock and magnetic holders release upon lockdown activation. Exceptions: doors 152,153 & 158
IN THE PROJECT MANUAL
ITEM
SECTION
PARAGRAPH
DESCRIPTION
ADD 1.05 to read:
01 1000
1.05 CONTRACTOR USE OF SITE
A. Time Restrictions:
1. Limit conduct to hours as per the City of
Kennewick Municipal Code .
07 4213
2.01A
ADD approved manufacturer:
The Bryer Company, Symmetry Series C23 or C64 panels:
www.thebryercompany.com
07 4213
2.02B
REVISE 4 to read:
4. Panel Width: 12 or 16 inches.
Addendum #2
Page 1
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE PROJECT MANUAL
ITEM
SECTION
PARAGRAPH
07 4264
2.01A
DESCRIPTION
ADD approved manufacturer:
Larson by Alucoil; Product 6mm ACM panels:
www.alucoilnorthamerica.com.
07 4264
2.01
ADD paragraph B to read:
B. Wall Panel System Manufacturers:
1. Phoenix Panels: www.phoenixpanels.com.
2. Substitutions: See Section 01 6000 - Product
Requirements.
07 4264
2.02A.1
08 7100
3.07
REVISE sheet thickness to be 4mm, minimum.
ADD line to HW1 to read:
Access control by others
08 7100
3.07
REVISE HW12 to:
Add (1) Power Supply PS902, Delete (1) DPS 2757L
08 7100
3.07
DELETE (1) DPS 2757L from HW14.
08 7100
3.07
ADD line to HW21 to read:
(1) DPS 2757L
08 7100
3.07
ADD line to HW25 to read:
Access control by others (reader both sides)
DELETE (1) key switch 653-04 L2
08 7100
3.07
REVISE HW26 to read:
3 ea Hinges TA2714 26D 4 ½ x 4 ½
1 set Push/Pulls 110 x 73C/73CL 630
1 ea Roller Latch 594 626 (mt @ head)
1 ea Vertical Housing HVD-32 - 96
2 ea Mag Lock M32
1 ea Push Button 625RD
1 ea Power Supply PS902
1 ea Overhead Stop 9-036 630
1 ea Kickplate K1062 10 x 1 ½ LDW 630 B4E
3 ea Silencers
1 ea Wiring Diagram
Wiring by elec contractor
Addendum #2
Page 2
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE PROJECT MANUAL
ITEM
SECTION
PARAGRAPH
08 7100
3.07
DESCRIPTION
ADD line to HW29 to read:
Access control by others
08 7100
3.07
ADD line to HW30 to read:
Access control by others
09 9123
3.07
REVISE H to read:
H. P-8: Benjamin Moore, Woodcliff Lake 980
10 1400
2.01A
ADD approved manufacturer:
Meyer Architectural Signs; Product Nova Photopolymer:
www.meyersignco.com.
10 1400
2.02C.6
ADD f to read:
f. Music Room: One (1) occupant load sign.
10 2226.33
2.04C
ADD 3 to read:
3. Cylinder cores to be keyed to School's keying system.
11 4000
2.03K.5
ADD subparagraphs c, d and e to read:
c. Loose Parts: Beacon II smart controller.
d. RRC (Remote Refrigeration Control).
e. Provide wireless remote alarm system.
11 4000
2.03K.6
ADD subparagraph e to read:
e. Provide wireless remote alarm system.
11 4000
2.03K
DELETE paragraph 7.
11 4000
2.03K
ADD item to read:
Height: 8'-0" overall.
Addendum #2
Page 3
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE PROJECT MANUAL
ITEM
SECTION
PARAGRAPH
23 0900
2.02-F
DESCRIPTION
Add paragraph 2. and associated subparagraphs to read
“Energy Monitoring and Reporting Display”
A. The energy monitoring and display system shall include all
necessary hardware, software and programming to display
real-time and historical energy consumption data with the
occupants of the building on a remote monitor provided and
installed by others. This monitor will not be dedicated to the
purpose of energy monitoring and reporting display as it may
also be utilized for general communications. The controls
contractor shall coordinate with the owner’s IT contractor and
is responsible for network interfacing and cabling between the
BAS workstation and the monitor system.
B. The system shall display real-time consumption (water,
gas, various electrical meters) and historical comparison
graphs. The live information will be shown on a gauge and the
historical information will be shown via a graph. This graph
shall show daily, weekly, monthly and yearly totalization.
23 2315
Various
Delete paragraphs 1.02-C, 1.04-C-2, 1.05-C, 1.07-C, 2.01-B,
2.01-C, 3.01-A-1-a, and 3.01-A-2 as aluminum piping is not
allowed.
23 2500
2.07
Add equipment tags to title “2.07 Sidestream Filter (FLTR-1,
FLTR-2)”
23 2500
2.07-B
23 2500
2.05-A
Add statement “Provide additional 20 gallon recovery tank for
boiler relief valves due to inability to pipe relief valve discharge
to main tank location.”
23 3100
3.05
Delete paragraph and subparagraphs. Underground ducts not
used.
23 3100
3.09-A
Clarify paragraph to read “Contractor shall test all 25% of total
duct area per NREC and all medium pressure ductwork (3”
w.g. and above pressure class).”
23 3300
2.10-A
23 3300
2.06-H
23 3300
2.08-C-4
23 5216
2.02-I.3
23 7200
2.3-G-2d
Addendum #2
Revise to read “Shelco Filters Model 4FQS1 FOS-80-4”
Revise to read “…U.L. leakage class II”
Delete paragraph
Delete paragraph.
Revise Safety Relief Valve Setting to 100-psig
Revise paragraph to read “Where indicated, provide airflow
monitoring device equal to TemFLO device…”
Page 4
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE PROJECT MANUAL
ITEM
SECTION
PARAGRAPH
DESCRIPTION
Revise all three paragraphs to read “Unless otherwise
indicated and where EC motors are specified, a separate VFD
is required for each fan motor in the unit and shall be factory
mounted and wired to motor. See VFD specifications section
230926.”
23 7200
2.3-G-2e, Q-2,
and R-2
23 7200
2.3.J.3
Revise paragraph to read “Flat plate aluminum air-to-air
crossflow heat exchanger.”
23 7000
2.3.C.1
Revise last sentence of 1st paragraph to read “The color of
AHU-1 thru -4 shall be custom and selected by architect.”
23 8226
2.01-H-1
26 2200
2.03
27 1500
2.02A
28 3100
2.06Q
Revise paragraph to read “Provide with control transformer
and/or relay for remote DDC thermostat by the control
contractor. See Control Diagrams on drawings and
Specification Section 23 0900”
Delete paragraphs L-N in their entirety
Delete sub-paragraphs 3-5. See 26 0533 for extra rough-in
and 26 2726 for extra receptacles.
Add the following:
In addition to the floor plan (Zone Map) sheet provide type
written instructions on how to reset the system.
IN THE DRAWINGS
ITEM
SHEET
L2.1/L2.2
DETAIL/DESCRIPTION
REVISE scale on drawings per LA-2/1.
1/A2.11
CHANGE wall type from 10A to 11A (see attached drawing AA-2/10).
5/A4.11
Dimension soffit over casework @ south wall of Music 115 (see attached drawing
AA-2/2).
1/A5.01
ADD 1'-0" handrail extension to top of ramp in RAMP 114.
Relocate back stage curtain support from suspended ceiling to soffit in MUSIC
115.
See attached drawing AA-2/6.
3/A5.01
CHANGE steel stud wall between Health 110 and RR 111 from 3 5/8" to 6" (see
attached drawing AA-2/9).
4/A5.01
Decrease opening width by 12" to GIRLS 132/202.
Swing non ADA stall doors inward.
See attached drawing AA-2/1.
Addendum #2
Page 5
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
6/A5.01
Swing non ADA stall door inward (see attached drawing AA-2/11).
3/A5.02
DELETE 3'-4" dimension from door into Quiet 152.
DELETE 1'-11 1/2" dimension @ casework between SP ED 150 and SP ED 153
ADD 1'-0" dimension to door into RR 151.
ADD 1'-6" dimension from casework to door between SP ED 150 and SP ED 153
(verify).
See attached drawing AA-2/12.
A5.03
ADD (+/-) to dimensions that read, "3'-3/8"" and "2'-8 7/8"" on 2/A5.03.
A6.00
Change note on 17/A6.00 to read, "PAINTED CMU (P-1), TYP."
A6.00
Remove note that reads, "CHAIR RAIL, TYP." from detail 2/A6.00.
A6.00
Remove note that reads, "IRP-1, TYP." from detail 2/A6.00.
A6.00
Change note on 4/A6.00 to read, "PAINTED CMU (P-1), TYP."
A6.00
ADD line to represent scheduled base to 10/A6.00.
A6.00
ADD line to represent scheduled base to 14/A6.00.
7/A6.01
CMU lintel to be @ 8'-0" above music floor (see attached drawing AA-2/4).
4/A6.01
CMU lintel to be @ 8'-0" above music floor (see attached drawing AA-2/5).
A6.01
CHANGE note on 1/A6.01 to read, "PAINTED CMU (P-1), TYP."
A6.01
CHANGE note on 7/A6.01 to read "PAINTED CMU (P-1), TYP."
A6.01
Fill in casework tag on 9/A6.01 to read, "15/A8.19".
A6.01
ADD note reading, "LOCKING ALL CABINETS, THIS ROOM, TYP." to 14/A6.01.
A6.02
ADD line to represent scheduled base to 6/A6.02.
A6.02
MOVE arrow down on 7/A6.02 and 12/A6.02 to point to mop rack.
A6.04
ADJUST wall hatch to fill entire wall on 2/A6.04 and 10/A6.04.
A6.04
REMOVE SHOWER note from 11/A6.04.
A6.04
REMOVE extraneous line work from 20/A6.04 and 1/A6.05.
A6.05
ADD note that reads, "INTEGRAL COVE BASE, TYP. AS SCHEDULED" to
6/A6.05, 11/A6.05 and 15/A6.05.
A6.06
ADD note that reads, "INTEGRAL COVE BASE, TYP. AS SCHEDULED" to
4/A6.06 and 14/A6.06.
A6.06
CHANGE wall finish from P-1 to VWC-1 above chair rail in elevations 18,19,20
and 21 on sheet A6.06.
A6.07
ADD note that reads, "(1) 8'-0" AND (2) 4'-0" MARKER BOARDS ON SLIDING
TRACK IN FRONT OF STORAGE CABINET" to 2/A6.07.
Addendum #2
Page 6
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
A6.07
ADD bookcase to 5/A6.07 to match adjacent bookcases.
A6.08
ADD line to represent scheduled base to 10/A6.08.
A6.08
ADD note that reads, "(1) 8'-0" AND (2) 4'-0" MARKER BOARDS ON SLIDING
TRACK IN FRONT OF STORAGE CABINET" to 2/A6.08.
A6.08
DELETE chair rail from 8/A6.08.
A6.11
ADD line to represent scheduled base to 5/A6.11.
A6.11
ADD line to represent scheduled base to 15/A6.11.
A6.12
MOVE arrow on 2/A6.12 to point to pendant fixture.
A6.13
CHANGE note on 1/A6.13 to read, "INSTALL TYPICAL WAINSCOT AT EAST
AND WEST WALLS OF ALCOVE W/ VWC ABOVE, TYP."
A6.16
DELETE elevations 14,15 and 16 from A6.16.
A6.16/A9.0
CHANGE finish of east wall of Office 117 from "CMU" to "PAINTED CMU (P-1),
TYP." in elevation 10/A6.16 and in Finish Schedule on A9.0.
Varies
Based on floor plan differences, classrooms on the north side of the building vary
slightly from classrooms on the south side of the building. Each general classroom
space has a consistent 16'-0" of marker board space. In addition to that, north
classrooms have 10-0" of open shelving space (4 @ 30" wide; see 14/A8.19 for
detail) and south classrooms have 8'-7 1/2" of open shelving space (2 @ 30" wide
and 1 @ 3'-7 1/2" wide; see 14/A8.19 for detail). Additionally, Classrooms 163 and
241 have only 4'-7 1/2" of open shelving (2 @ 2'-3 3/4" wide; see 14/A8.19 for
detail). Resource classroom 173 is configured like Computer Lab 231. See floor
plans for additional information. Verify all dimensions in field.
1/A7.11
Center fixtures on both sides of opening between MULTI-PURPOSE 118 and
MUSIC 115.
Relocate back stage curtain support from suspended ceiling to soffit in MUSIC
115.
Dimension south wall soffit in MUSIC 115.
CMU lintel to be @ 8'-0" above music floor.
See attached drawing AA-2/3.
1/A7.11
REMOVE detail callouts 20/A8.16 from soffits on east side of Commons 130.
1/A7.11
ADD light fixtures in PE OFFICE125 (see attached drawing AA-2/7).
1/A7.11
ADD light fixtures to wash soffit between GIRLS 132 and BOYS 133 (see attached
drawing AA-2/8).
1/A7.21
ADD light fixtures to wash soffit between GIRLS 202 and BOYS 203 (see attached
drawing AA-2/8).
1/A7.21
ADD note that reads, "PAINT CEILING AND STRUCTURE P-6, TYP" to
Commons 130 ceiling.
Addendum #2
Page 7
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
A8.01
REVISE door 119A type to "HM/FRP".
A8.01
CHANGE frame depth of door 111 from 5 7/8" to 8 1/4".
A8.01
CHANGE width of door 152 from 3'-0" to 3'-2".
A8.16
CHANGE 3" dimension on 11/A8.16 to read, "6".
S2.11
MOVE columns and rectangular footing on grid 10 1” to the east, as shown on
attached drawing SA-2/1. Floor beams and roof beams above also move to
maintain alignment with columns.
S2.21
CHANGE the W14x22 floor beam, spanning in the north/south direction and
located approximately 9’-6” east of the elevator shaft, to an 18LH4 bar joist.
S2.42
CHANGE the 6’-9” plan dimension to 6’-8” to account for the beam line on grid 10
moving 1” to the east, as shown on attached drawing SA-2/2.
S4.3
REDUCE the plan dimensions of the concrete pedestals at the exterior canopy
columns as shown on attached drawing SA-2/3.
S5.1
MOVE the floor beam located below the framed wall 1” to the east, as shown on
attached drawing SA-2/4.
M1.1
AHU-1 thru AHU-7 and FC-1 thru FC-6: Add sound data. See attached
clarification drawing MA-2/1.
M1.1
AHU-1, -2, -3, -4: Revise heat exchanger outdoor air winter leaving dry bulb (LDB)
to 49 degrees F. Revise heating coil entering dry bulb (EDB) to 65 degrees F.
Revise heating coil MBH to 150, 130, 130, and 140 respectively.
M1.1
AHU-5, -6, -7: Remove note #9 referring to VFDs on supply and return fans. Add
note #3 to read “Provide EC motors on supply and return fans with manual speed
adjustment dials factory mounted in the control panel for use in TAB.”
M1.1
AHU-5, -6, -7: Revise supply fan horsepower to 7.5 hp, 7.5 hp and 2.0 hp
respectively. Overall electrical data does not change.
M1.1
VAV-109: Revise maximum CFM to 1000 cfm
M1.1
VAV-111: Revise maximum CFM to 1800 cfm
M1.1
VAV-204, -205, -211, -212, -304, -305, -311, -312, -403, -404, -410: Revise
minimum CFM to 600 cfm
M1.1
VAV-408: Revise minimum CFM to 150 cfm
M1.1
FC-1: Revise model to Destiny LAH005A.
M1.2
Add dryer exhaust booster fan EF-9, Fantech Model DBF4XL, 115V. Provide with
lint trap and factory pressure sensor to automatically turn the fan on when the
dryer is on.
M1.2
Add Sound Attenuator Schedule. See attached clarification MA-2/2.
Addendum #2
Page 8
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
M1.2
Add AC-4 and CU-4 to ductless split system indoor and outdoor unit schedules
respectively. All specifications are identical to AC-3 and CU-3.
M1.3
Pumps P-1 and P-2: Revise head and rpm for to 90-ft and 1750 rpm respectively.
M1.3
Hot Water Finned Tube Radiation Schedule: Remove EWT and LWT data as it
varies depending on specific instance.
M1.3
Hot Water Finned Tube Radiation Schedule: Revise duplicate FT-6 at end of
schedule to FT-7.
M1.3
Hot Water Finned Tube Radiation Schedule: Revise GPM for FT-1, FT-3 and FT-4
to 1.0 gpm.
M2.11
Add dryer vent in Health-110 along with booster fan EF-9. See clarification MA2/3.
M2.11
Add transfer grilles and duct between MPR and Kitchen. See MA-2/3.
M2.11
Add DDC room temperature sensors in Freezer-119A and Cooler-119B for
monitoring only as indicated by control diagram 4/M7.1.
M2.11
Add a note at room temperature sensor in Machine-124 to state “DDC sensor for
monitoring only as indicated on control diagram 10/M7.0.”
M2.11
Revise keynote #29 to read “…duct riser serving the Gym…”
M2.11
Add sound attenuators SA-7 and SA-8 at supply and return ducts respectively from
AHU-7 in the kitchen.
M2.11
Add 20x10 duct size callout on kitchen hood KH-1 exhaust duct.
M2.11
Add keynote callout #23 at transfer grille at south wall of Mech-134.
M2.12
Revise keynote #4 to read “8x8 type 5, 100 cfm”
M2.12
Remove EUH-5 in Elec-156 (room under Stair-155).
M2.12
Add ductless split indoor unit AC-4 above door in Elec-156 (room under Stair-155)
and room sensor for monitoring only per control diagram 10/M7.0.
M2.11
Add 44x18 duct size callout on return duct for AHU-5 above PE Off-125.
M2.21
Add dryer vent and a couple notes. See clarification MA-2/4.
M2.21
Add a note at room temperature sensor in Machine-201 and Data-200 to state
“DDC sensor for monitoring only as indicated on control diagram 10/M7.0.”
M2.21
Add keynote callout #10 on ducts from AHU-5 and AHU-6 where they turn upward
between grids 3 and 5.
M2.21
Add diffuser callout “48x48 Type 3 on top side of duct” on main return ducts from
AHU-1 and AHU-2 where they turn up.
M2.22
Revise CFM of the six north classroom displacement diffusers from 1200 cfm to
1300 cfm.
Addendum #2
Page 9
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
M2.22
Revise keynote callout #2 on transfer grilles at SGIC-214 and SGIC-219 to
keynote #1.
M2.22
Add diffuser callout “48x48 Type 3 on top side of duct” on main return ducts from
AHU-3 and AHU-4 where they turn up.
M2.41
Add note “2-inch duct liner on exterior ductwork” at exterior supply ducts from
AHU-5 and AHU-6.
M2.41
Add dryer vent termination. See clarification MA-2/5.
M2.42
Add ductless split outdoor unit CU-4 6-ft north of EF-6.
M3.11
Revise HWS/HWR pipe size running south over Cust Office-135B from 1-1/2” to
2”.
M3.11
Revise HWS/HWR runouts to CUH-1 to 3/4”.
M3.11
Add reference to detail 4/M5.1 in keynotes #1 and #2.
M3.11
Revise keynote #14 to read “Control valves for AHU-6 to be 3-way.”
M3.11
Add 3/4" condensate drain line from AC-3 in Elec-124 to mop sing in RR-121.
M3.11
Relocate keynote callouts #14 and #15 on runouts to AHU-5 above Com Stor-123
to AHU-6 runouts above kitchen.
M3.11
Add line size callout of 2” on branch connections feeding AHU-6 and AHU-7 above
Table Stor-122.
M3.12
Revise equipment tag FT-1 at each classroom displacement ventilation diffuser to
FT-5. The reading nook tags remain FT-1.
M3.12
Remove panel heaters in restroom RR-151 and RR-154. See attached
clarification MA-2/6.
M3.12
Revise heating water runouts to CUH-2 to 3/4".
M3.12
Add ductless split indoor unit AC-4 above door in Elect-156 (under Stair-155) and
note “Refrigerant line set up to condensing unit on roof through common walls of
Cust-157 and Cust-224. See sheet M2.41 for condensing unit location. See detail
8/M5.0.”
M3.21
Replace detail callout 1/M5.0 at Library-226 with note that shall read “Fin-tube
heater installed within book casework. See arch details.”
M3.21
Add note at FC-4 and FC-6 to read “3-way heating and chilled water valves. See
system diagram and details.”
M3.21
Revise several pipe sizes and add detail callout 9/M5.1 at piping penetration
through floor of Mech-205. See clarification MA-2/7.
M3.21
Revise equipment tag FT-4 in Title-206 to FT-7.
M3.21
Revise equipment tag FT-4 in Coun-204 to FT-3.
M3.21
Add reference to detail 9/M5.1 in keynote #2.
Addendum #2
Page 10
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
M3.22
Revise HWS/HWR line sizes at Grid 12-H from 3” to 2”. Revise
HWS/HWR/CWS/CWR line sizes at Grid 14-H from 3” to 1.5”. Revise runouts to
AHU-3 and AHU-4 to 1” HWS/HWR and 1.5” CWS/CWR.
M3.22
Add reference to detail 9/M5.1 in keynote #2.
M3.23
Add boiler relief tank, VFDs, BAS Panel and boiler EPO switch. See clarification
drawing MA-2/8.
M3.23
Add VFD’s, detail callouts on filters and boiler EPO switch. See clarification MA2/9.
M5.0
Detail 2: Revise detail callout 3/M5.0 at roof penetration to 1/M5.0
M5.0
Detail 3: Add note “Mount to concrete curb at exterior wall with top of heater flush
with top of curb in order to provide approx 3” clear below the heater.”
M5.0
Detail 9: Revise detail callout 10/M-504 at roof penetration to 7/M5.0
M5.1
Detail 1: Revise factory relief pressures of both relief valves from 50-psig to 100psig.
M5.1
Detail 3: Revise note to air vent to read “High capacity automatic air vent. Route
discharge to glycol recovery tank.”
M5.1
Detail 7: Revise “Pressure Independent Balancing Valve” on the heating water
return line to “Venturi” and revise line designation from HWR to HWS.
M5.1
Detail 8: See clarification MA-2/10.
M5.2
Detail 5: See clarification MA-2/11.
M5.2
Detail 9: Remove damper and add external duct insulation up into the curb.
M5.3
Delete Detail 6 as it duplicates Detail 6 on M5.2.
M5.4
Detail 9: Revise detail callout 7/M5.4 to 10/M5.4.
M5.4
Detail 10: Revise reference to detail 6 at the platform to reference detail 9.
M5.4
Delete Detail 7 as it duplicates Detail 2.
M5.4
Delete Detail 6 as it duplicates Detail 3.
M5.5
Detail 2: Revise title to read “Air Handler Details (AHU-5, -6, -7)”
M5.5
Detail 2: Revise keynote #2 to read “Angle filter, 2-inch MERV-8 + 2” MERV-13”
M5.5
Detail 2: Revise keynote #3 to read “Return fan, direct drive plenum type with
ECM”
M5.5
Detail 2: Revise keynote #8 to read “Supply fan, direct drive plenum type with
ECM”
M5.5
Detail 2: Revise keynote #15 to read “24-inch tall roof curb sloped to
accommodate sound attenuators below and match roof slope. Curb footprint shall
include piping vestibule.”
Addendum #2
Page 11
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
M6.0
Re-issue entire sheet.
M7.0
Detail 4: Clarify overlapping text “…cut-off mode. Under this mode, all air handling
units shall be signaled to close outside air intake dampers…”
M7.0
Detail 6: Clarify overlapping text “Peak Demand History: The controller shall
monitor and record the peak (high and low) demand readings from the gas meter.
Peak readings shall be recorded on a daily, month-to-date, and year-to-date basis.
Usage history: The controller shall monitor and record gas meter readings so as
to provide a gas consumption history. Usage readings shall be recorded on a daily,
month-to-date, and year-to-date basis.”
M7.1
Detail 4: Clarify overlapping text “Room temp sensor shall be suitable for freezing
conditions and shall be flush mounted with a stainless steel cover
plate. Coordinate with kitchen equipment.”
M7.3
Detail 1: Revise title to “Multi-purpose Room AHU and Kitchen Pressure Control
Diagram (AHU-6).”
M7.3
Detail 1: Change all VFDs to EC Motors
M7.3
Add pressure sensor in kitchen and associated analog input (AI) ad controller.
M7.3
Detail 1: Revise exhaust fan numbers for Kitchen and Dishwasher Hoods to EF-7
and EF-8 respectively.
M7.3
Detail 1: Add outdoor airflow measuring station at outdoor air intake and
associated analog input (AI) at DDC controller.
M7.3
Detail 2: Revise title to “ Gymnasium and Kitchen AHU Control Diagram (AHU-5,
AHU-7)”
M7.3
Detail 2: Change all VFDs to EC Motors
M7.3
Detail 2: Add outdoor airflow measuring station at outdoor air intake and
associated analog input (AI) at DDC controller.
M7.3
Detail 2: Revise sequence of operations paragraph 3 to read “The CO2 sensor
(not applicable to AHU-7) shall modulate the outside air damper…”
P2.11
Revise reference to “food service drawings” in general notes #1 and #4 to
reference “architectural drawings”.
P2.11
Relocate 4” COTF shown in Freezer-119A approximately 18” south so it’s no
longer in the freezer room.
P2.11
Install rain leaders in wall per clarification drawing PA-2/1.
P2.12
Add keynote #12 to read “1-inch CW DN”
P2.12
Add keynote #13 to read “3-inch W up with P-trap and Primer”
P2.12
Add keynote #14 to read “2-inch V up”
P2.21
Revise note “4-inch Gas DN” to gas line at grid 5 to “3-inch Gas DN”
Addendum #2
Page 12
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
P4.01
Detail 2: Revise “N.I.C.” notation at full size bypass valve to “N.C.” to indicate
Normally Closed.
E0.01
Delete OFOI & OFCI remarks in the Communications symbols note column
E0.02
Change luminaire Type S20 and S20P to have 2 light engines and provide with
dual switching.
E0.03
Delete the electrical materials and connections to CUH-2, CUH-3, CUH-6 & CUH7
E0.03
Change the circuit number for EF-9 to A2-9
E0.03
Add split system AC-4/CU-4 to schedule. Same material and requirements as AC3/CU-3. Use circuit M-10,12
E1.01A
Clarification: This drawing is informative only and is included to indicate the
basis-of-design photometric performance. Approved equal fixtures shall meet or
exceed the point by point photometry values.
E2.11
Change LCM1 that control luminaire Type S20 to LCM2 in all locations.
E2.12
Change LCM1 that control luminaire Type S20 to LCM2 in all locations.
E3.11
Add a card access reader, electric door hardware rough-in, magnetic door holder
connection, relay and 120V circuit/connections to power supplies for door 114 per
drawing EA3.11A
E3.11
Add magnetic door holder connection, relay and 120V circuit/connections to power
supplies for door 118B per drawing EA3.11A
E3.11
Add magnetic door holder connection, relay and 120V circuit/connections to power
supplies for doors 118A & 127D per drawing EA3.11B
E3.11
Add two card access readers, electric door hardware rough-in and 120V
circuit/connections to power supplies for door 127B per drawing EA3.11B
E3.11
Change power supply location for door 127D to flush enclosure as indicated on
drawing EA3.11B
E3.11
Add electric door hardware rough-in and 120V circuit/connections to power supply
for door 118C per drawing EA3.11C
E3.11
Delete rough-in for door position switches at 119A, 119C & 119D
E3.11
Add a card access reader for the elevator located east of the elevator door in
Commons 130.
E3.11
Add 135 degree, 120VAC fixed temperature heat detectors in the elevator pit
located within 18” of the sprinkler heads
E3.11
Change the location of the receptacle located on the west wall of Conference
Room 108 to be 6” south of the casework niche
E3.11
Delete EF-1 connection from room 124
Addendum #2
Page 13
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
E3.11
Change the location of EUH-2 in room 174 to be west of door 174. Move the
receptacle in that location to the adjacent west wall
E3.11
Change the location of the mechanical equipment in room 134 to that shown on
the mechanical drawings. See the mechanical addendum for the pump VFD
locations
E3.11
Add two 120V circuits and two data drops to the BAS panels located on the east
wall of room 134. See mechanical addendum. Use spare circuits MA-11 & 13
E3.11
Add two security alarm motion sensors in multi-purpose room 118. Locate one on
the north wall and one on the south wall facing doors 118A & 118B
E3.12
Delete CUH-2 & CUH-3
E3.12
Delete EUH-5
E3.12
Add AC-4 in room 156 above door
E3.12
Add electronic door hardware connections to doors 152, 153 & 158 per drawing
EA3.12A. For door 152, provide a momentary contact switch that will manually
engage the electronic lock as long as the switch is depressed
E3.21
Add 135 degree, 120VAC fixed temperature heat detectors in the elevator
machine room 201, located within 18” of the sprinkler heads
E3.21
Add a fire alarm system smoke detector in elevator machine room 201
E3.21
Add a fire alarm system connection to the PMP to monitor the heat detector and
shutdown operating voltage
E3.21
Add a card access reader for the elevator located east of the elevator door in
Corridor 225
E3.22
Delete CUH-6 & CUH-7
E3.30
Change EF-9 callout to EF-1
E3.30
Add CU-4 to plan, located 6’ north of EF-6
E5.01
Add the following note to K8:
PROVIDE SWITCH WITH PILOT LIGHT AND ID TAG FOR EXHAUST FAN
E5.01
Add a SPST switch with a pilot light to the south wall of the hood enclosure.
Provide an ID tag stating EXHAUST FAN
E6.01
Change MDS amp rating to 1,000A
E6.01
Change service lateral between the BPUD transformer and MDS to (3) sets 31/2”C., 3#600 KCMIL (AL), #600 KCMIL (AL) N.
E6.01
Change dry-type transformer XSDP to 300kVA
E6.01
Change feeder between the MDS and transformer XSDP to (2) sets 3”C., 3#350
KCMIL (AL), #2G.
Addendum #2
Page 14
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
IN THE DRAWINGS
ITEM
SHEET
DETAIL/DESCRIPTION
E6.01
Change feeder between transformer XSDP and SDP to (3) sets 3-1/2”C., 3#600
KCMIL (AL), #600 KCMIL (AL) N., #3/0G.
E6.01
Change SDP main breaker and bus rating to 1,000A
E6.01
Delete the main circuit breaker in PDP
E6.01
Change the DS1 circuit breaker and DS1 bussing to 400A in MDS
E6.01
Change panel C3 feeder to 2-1/2”C. 3#250 KCMIL (AL), #250 KCMIL (AL) N, #6G.
E6.01
Change panel MC feeder to 1-1/2”C. 3#1/0 (AL), #1/0 (AL) N, #6G.
E6.01
Change the AIC ratings for panels A1, A2, B1, B2, C1, C2, D1 & D2 to 10,000
E6.02
Replace panel schedules for MDS, DS1, PDP & SDP with the schedules issued in
this addendum; drawings E6.02A & E6.02B
E6.03
Change the AIC ratings for panels A1, A2, B1, B2 & C1 to 10,000
E6.03
Change MC-26-29 and MG-1 to SPARE
E6.03
Add dryer booster fan EF-9 connection in room 112, south wall.
E6.03
Add BAS panels to circuits MA11 & 13
E6.04
Change the AIC ratings for panels C2, D1 & D2 to 10,000
PRIOR APPROVALS
ITEM SECTION
DETAIL/DESCRIPTION
This approval is an approval of quality only. No attempt has been made to check each material as to
special features, capacities or physical dimensions especially required by this project. It shall be the
responsibility of supplier, manufacturer and Contractor to check all requirements before submitting for
final approval. Final approval of exact features, sizes, capacities, etc., all of which must match materials
indicated/specified, will be determined when submitted during construction period. Certain approvals
are subject to conditions as noted.
Vibration Isolators – Vibro-Acoustics
230548
VFD’s – JCI (approved only for factory mounting in Air Handling Units)
230926
Flexible Pipe and Equipment Connections – Nexus
232115
Flexible Pipe and Equipment Connections – Griswold
232115
Y-Pattern Strainers – Nexus
232115
Venturis - Nexus
232115
Venturis - Griswold
232115
Duct Silencers – VAW Systems
233300
Addendum #2
Page 15
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
PRIOR APPROVALS
ITEM
SECTION
233600
233723
233723
233723
233723
235100
235216
237200
238226
238233
DETAIL/DESCRIPTION
Single Duct VAV Units - JCI
Roof Hoods – Twin City Fans
Roof Hoods – Loren Cook
Roof Hoods – Penn Barry
Exterior Louvers – United Enertech
Condensing Appliance Vents - Schebler
Condensing Boilers – Fulton
Outdoor Air Handling Units - Venmar
Electric Heaters - Qmark
Fin Tube Heaters - Modine
26 5100
A24
Lumenwerx
VIA2 Series
26 5100
A28
Lumenwerx
VIA2 Series
26 5100
C24
Lithonia
ZL1DL48 3000LM FST WH
26 5100
C24E
Lithonia
ZL1DL48 3000LM FST E7W WH
26 5100
C26
Lithonia
ZL1DL48 3000LM FST WH
26 5100
D01-4
Lumenwerx
Reveal Series
26 5100
D01-8
Lumenwerx
Reveal Series
26 5100
D01-8E
Lumenwerx
Reveal Series
26 5100
D01-12
Lumenwerx
Reveal Series
26 5100
D10
Lumenwerx
Quad Series
26 5100
D10E
Lumenwerx
Quad Series
26 5100
S03
LSI
Xenm3 Series
26 5100
S11
ERCO
Tesis Series
26 5100
S13
LSI
Xenm3 Series
26 5100
S20
Spaulding
TRP Series
26 5100
S20P
Spaulding
TRP Series
26 5100
S23
LSI
Xenm3 Series
26 5100
S51
MP Lighting
L22 Series
26 5100
T12
AFX
ALV Series
26 5100
T20
ConTech
CTL825 Series
Addendum #2
Page 16
7601 W. Clearwater Ave., Ste 206
Kennewick, Washington 99336 1 N. Monroe, Ste. 200
Spokane, Washington 99201
www.mmecarchitecture.com
PRIOR APPROVALS
ITEM
SECTION
DETAIL/DESCRIPTION
26 5100
X01
DualLite
SE Series
26 5100
X02
DualLite
SE Series
26 5100
X03
DualLite
SEWL Series
26 5100
G01
Kenall
MLHA12 48 R MW PP 150L40K DCC 1
DV
26 5100
G02
Kenall
MLHA12 24 R MW PP 45L40K DCC 1
DV W/EMERGENCY BATTERY PACK
END OF ADDENDUM NO. 2
Addendum #2
Page 17
SCD
SCD
5' - 0"
1' - 6"
5' - 0"
4' - 0 3/4"
17'-0" (FACE OF GWB TO FACE OF GAWB)
CLR.
5' - 0"
TPD
5' - 0"
1' - 6"
TPD
SNR
5' - 0 3/4"
9' - 3"
CLR.
1' - 10"
10' - 3"
TYP.
17' - 4 7/8"
2
SCD
2' - 11"
3' - 0"
SCD
SNR
TPD
2
TPD
2
2
4' - 1 1/4"
2' - 11"
SCD
2' - 11"
2
2
TPD
SNR
5
A6.05
3
4
TPD
SCD
2' - 11"
19
18
SNR
SNR
6' - 1 1/4"
A6.04
20
3' - 0"
2
3' - 0 1/8"
17
3' - 0"
SCD
TPD
PTD
SD
SD
13' - 1 1/2"
PTD
2
4' - 1 1/4"
1
A6.05
4
ENLARGED TOILET ROOM 132 & 202, 133 & 203 PLAN
SCALE: 1/4" = 1'-0"
REF. DWG. 4/A5.01
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/10/16
RMS
DCM
1/4" = 1'-0"
AA-2/1
N
O
2
2' - 0"
SOFFIT ASSEMBLY
8"
TYPE A
INSET 3/4"
2' - 0"
TYPE A
8"
TYPE A
INSET 3/4"
TYPE A
7' - 2"
1' - 8"
09 21 16.GB58
3' - 4"
09 21 16.SS358
8"
FLOOR ASSEMBLY
TYPE A
INSET 3/4"
2' - 8"
3
A8.14
TYPE A
03 30 00.SL
05 31 00.SD
Level 1
Level 1
0' - 0"
5
0' - 0"
WALL SECTION
SCALE: 1/2" = 1'-0"
REF. DWG. 5/A4.11
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/16/16
RMS
DCM
1/2" = 1'-0"
AA-2/2
2
CENTER FIXTURE
CENTER FIXTURE
2
K
6' - 0"
L
1
A8.10
P-6, TYP.
26
P-6
2
MUSIC
115
STG
113
L
10' - 8"
10' - 0"
P-6
8'-0" AB.
MUSIC
FLOOR
M
STG.
M
20
A8.16
25
16' - 4"
116
6' - 0"
RAMP
6' - 0"
16' - 0"
28
P-6
6' - 0"
2
N
20
A8.16
P-6
TYP.
114
P-6
O
6
1
PARTIAL LEVEL 1 REFLECTED CEILNG PLAN (WEST)
SCALE: 1/8" = 1'-0"
REF. DWG. 1/A7.11
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/16/16
RMS
DCM
1/8" = 1'-0"
AA-2/3
3' - 4"
3' - 4"
P-2
P-3
P-5
4' - 0"
P-4
8' - 0"
OPEN TO
RAMP
8"
2
7
MUSIC 115
SCALE: 1/4" = 1'-0"
REF. DWG. 7/A6.01
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/17/16
RMS
DCM
1/4" = 1'-0"
AA-2/4
PAINTED CMU
(P-1), TYP.
13
2
A8.15
OPEN TO
MUSIC ROOM
16
P-3
P-2
P-4
P-5
P-2
P-3
P-5
TYP.
A8.16
P-4
P-2
P-4
PARTIAL
HEIGHT WALL,
TYP.
P-3
RAILING, TYP.
P-3
P-5
P-2
GYP. BD.
REVEAL, TYP.
P-3
4
P-4
P-2
P-5
P-2
P-4
P-3
RAMP 114
SCALE: 1/4" = 1'-0"
REF. DWG. 4/A6.01
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/17/16
RMS
DCM
1/4" = 1'-0"
AA-2/5
STG
7 5/8"
113
1' - 0"
11' - 0"
9' - 4"
FIRE EXTINGUISHER
CABINET (F.E.C.), TYP.
UP
115
2
5
1' - 0"
MUSIC
20' - 6 1/2"
A6.01
6
2
A6.01
8
RAMP
10' - 0"
114
1
A6.01
17' - 8"
3' - 4 5/8"
1
1:12 MAX.
SLOPED
RAMP
3
2
4' - 1 3/8"
5 5/8"
ENLARGED MUSIC ROOM PLAN
SCALE: 1/4" = 1'-0"
REF. DWG. 1/A5.01
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/18/16
RMS
DCM
1/4" = 1'-0"
AA-2/6
2
3
B
B
PE STOR
126
9' - 0"
PE OFF
125
2
COM STOR
123
C
C
ELEC
124
2
1
PARTIAL LEVEL 1 REFLECTED CEILNG PLAN (WEST)
SCALE: 1/8" = 1'-0"
REF. DWG. 1/A7.11
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/21/16
RMS
DCM
1/8" = 1'-0"
AA-2/7
10
GIRLS
BOYS
132
BOOKS
133
P-1
9'-0"
A.F.F.
19
10' - 0" A8.16
28
9'-0"
A.F.F.
P-1
135A
10' - 0"
10' - 0"
P-3
9' - 0"
2' - 0"
2
G
20
A8.16
G
10
1
PARTIAL LEVEL 1 REFLECTED CEILNG PLAN (WEST)
SCALE: 1/8" = 1'-0"
10
GIRLS
BOYS
9'-0"
A.F.F.
202
19
P-1
10' - 0" A8.16
28
2
G
P-6
9'-0"
A.F.F.
203
P-1
10' - 0"
P-3
2' - 0"
9' - 0"
20
A8.16
P-6
G
9'-0"
A.F.F.
10
2
PARTIAL LEVEL 2 REFLECTED CEILING PLAN (WEST)
SCALE: 1/8" = 1'-0"
REF. DWG. 1/A7.11 & 1/A7.21
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/21/16
RMS
DCM
1/8" = 1'-0"
AA-2/8
SND
12
9
7 1/4"
A6.04
6' - 1 1/4"
PTD
1' - 6"
3' - 1"
SD
3' - 2"
1' - 0"
10
RR
111
3' - 1"
11
TPD
3' - 4"
1
SNR
2
8' - 8"
ENLARGED TOILET ROOM 111 PLAN
SCALE: 1/4" = 1'-0"
REF. DWG. 3/A5.01
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/25/16
RMS
DCM
1/4" = 1'-0"
AA-2/9
A6.02
1' - 4"
1' - 4"
6 5/8"
7
112
10' - 0
"
1' - 4"
112
H
10A
10E
10A
10A
I
11D
10H
10A
10H
RR
5
46
111
10E
10H 10E
10A
10E
10H
25' - 4"
A4.23
108A
CUST
111
2
K
11A
17
1' - 4"
1' - 1"
10A
A6.00
10A
15
L
HEALTH
16
2' - 8"
11A
M
11E
14
110
6' - 0"
10A
11
101
U
J
110
3' - 9 1/2"
M
10A
RECEPTION
101
8
1
PARTIAL LEVEL 1 FLOOR PLAN (WEST)
SCALE: 1/8" = 1'-0"
REF. DWG. 1/A2.11
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/25/16
RMS
DCM
1/8" = 1'-0"
AA-2/10
5/8"
160
7
1' - 6"
2
10' - 3 1/4"
A6.06
GIRLS
6
SD
17
5' - 0"
CLR.
SNR
TPD
5' - 0"
2' - 10 1/8"
PTD
A6.06
18
TPD
SCD
SCD
SNR
5/8"
11' - 8"
4' - 0"
19
5/8"
3' - 10 3/4"
1' - 8"
5' - 0"
SD
A6.06
8
8' - 10"
20
SND
5' - 1"
5
PTD
RR
15
162
4' - 0"
SNR
A6.06
1' - 6"
10
11
BOYS
161
5/8"
TPD
12
TPD
9' - 8 3/4"
8' - 10"
14
SCD
9
5' - 0"
SND
1' - 6"
7' - 6"
PTD
A6.06
5' - 0"
CLR.
13
16
2' - 10 1/8"
5' - 0"
3' - 10 3/4"
SD
4' - 6 1/2"
1' - 6"
SCD
7' - 6"
6
1' - 8"
12' - 4"
ENLARGED TOILET ROOM 160 & 242, 161 & 243, 162 & 244
SCALE: 1/4" = 1'-0"
REF. DWG. 6/A5.01
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
RMS
DCM
1/4" = 1'-0"
AA-2/11
5' - 3 7/8"
7 1/4"
1' - 8"
3' - 11 3/4"
6' - 2 3/4"
TPD
14
1' - 5 7/8"
7' - 2 1/8"
17
RR
A6.05
15SD
16
SCD
4
A6.06
3
151
RR
154
1' - 0"
1' - 6"
TPD
1' - 6"
2
2
9' - 9 1/4"
1
SP ED
150
STORAGE CABINETS
BEHIND WHITEBOARDS
SP ED
3' - 4"
2
1' - 6"
153
2 1/2"
6' - 1 1/4"
3
ENLARGED SPECIAL ED PLAN
SCALE: 1/4" = 1'-0"
REF. DWG. 3/A5.02
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
RMS
DCM
1/4" = 1'-0"
AA-2/12
O N
M
2
CP
A1
EAST ELEVATION
1
SCALE: 1/16" = 1'-0"
D EF
CH
CG
G
CF
CD
H
CE
I
2
J
CE
K
L
M
N O
CD
CC
CB
CA
C
2
WEST ELEVATION
SCALE: 1/16" = 1'-0"
REF. DWG. 1 & 2/A3.00
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
RMS
DCM
1/16" = 1'-0"
AA-2/13
10
2
15'-7"
6'-7 1/2"
3"
TYP
6
S4.1
C
C5
C5
FTG 2'-0"x12" DP
W/ 3-#4 CONT
TYP, UNO
C4
7
4
2'-6"
C5
C5
10'-1 1/2"
C5
10'-6"
L
S3.1
2'-6"
2
12'-0"
4
C5
10
REF DWG S2.11
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
JAQ
LAH
1/8" = 1'-0"
SA-2/1
10
W14x22
W14x22
W14x22
5
S6.8
7
S6.8
W18x40
G
W16x26
11
S6.7
AHU 12,000#
3'-9"
W21x44
2'-4"
W16x26
2'-2"
/8
3'-0"
1
SIM S6.7
GATE
24K8
W14x22
x
S6
HS
10B
S6.7
3
4x
E
OF A S
I
GA DE
TE
H
9'-1"
9'-0"
W14x22
CH
7500#
6
S6.8
6'-8"
6'-3"
2'-10"
6'-3"
9'-0"
2
W16x26
9
S6.7
W16x26
F
W14x22
2'-8"
/8
x3
x4 O
S 4 UN
HS YP,
T
D
4'-8"
2'-0"
20K4
J
10
REF DWG S2.42
Westgate Elementary School Replacement
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
JAQ
LAH
1/8" = 1'-0"
SA-2/2
AIR
E IN DIV 23
S.
HOT WATER
2
SOUND DATA
SUPPLY/RETURN SOUND POWERED LEVELS
#
NOTES
63
HZ
125
HZ
250
HZ
500
HZ
1000
HZ
2000
HZ
4000
HZ
8000
HZ
AHU
1
94/81
94/82
94/86
97/88
96/82
93/81
88/77
84/73
1
3
AHU
2
94/81
94/82
94/86
97/88
96/82
93/81
88/77
84/73
1
3
AHU
3
94/81
94/82
94/86
97/88
96/82
93/81
88/77
84/73
1
3
AHU
4
94/81
94/82
94/86
97/88
96/82
93/81
88/77
84/73
1
3
AHU
5
74/67
71/73
81/79
83/78
78/72
84/73
82/71
77/69
1
3
AHU
6
74/67
72/73
81/79
84/78
84/72
85/73
85/71
79/69
1
3
AHU
7
66/67
62/64
74/77
73/77
75/73
72/73
68/73
64/71
1
3
FC
1
NL
77/80
72/79
69/79
73/81
70/79
65/76
66/71
2
3
FC
2
NL
77/80
72/79
69/79
73/81
70/79
65/76
66/71
2
3
FC
3
NL
73/80
78/78
66/75
64/71
67/75
63/71
72/70
2
3
FC
4
NL
72/76
70/71
60/72
60/69
64/71
57/66
64/60
2
3
FC
5
NL
77/80
72/79
69/79
73/81
70/79
65/76
66/71
2
3
FC
6
NL
81/83
74/82
71/83
71/81
70/78
66/76
70/70
2
3
PERFORMANCE DATA BASED ON 65F AIR AND 30% GLYCOL HEAT
HOT WATE
H
SOUND
NOTES:
1
SUPPLY / RETURN FAW FAN SOUND POWER LEVELS
2
RETURN INLET / SUPPLY OUTLET SOUND POWER LEVELS
3
SOUND DATA ARE CALCULATED +/-3 DB. MEASURED
VALUES SHALL NOT EXCEED THESE.
REF DWG M1.3
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/16" = 1'-0"
MA-2/1
FT
DIA
MATERIAL
SIZE
FPI
MATERIAL
VELS
2
SOUND ATTENUATOR SCHEDULE
INSERTION LOSS (DB)
#
MFR
MODEL
LOCATION
TYPE
WxH
(IN)
LENGTH
(IN)
CFM
FPM
IN.WG.
63
HZ
125
HZ
250
HZ
500
HZ
1000
HZ
2000
HZ
4000
HZ
8000
HZ
SA
1
RUSKIN
ELBMP5
AHU-1
RETURN
RECT.
ELBOW
50X28
30 UP
30 DN
13000
-1400
0.50
4
9
17
26
25
24
20
16
1
2
SA
2
RUSKIN
ELBMP5
AHU-2
RETURN
RECT.
ELBOW
50X28
30 UP
30 DN
11600
-1200
0.35
4
9
17
26
25
24
20
16
1
2
RECT.
ELBOW
50X28
30 UP
30 DN
11600
-1200
0.35
4
9
17
26
25
24
20
16
1
2
NOTES
SA
3
RUSKIN
ELBMP5
AHU-3
RETURN
SA
4
RUSKIN
ELBMP5
AHU-4
RETURN
RECT.
ELBOW
50X28
30 UP
30 DN
12600
-1350
0.40
4
9
17
26
25
24
20
16
1
2
TAPERD
RECT.
44X18
36
5000
-1000
0.25
7
10
20
30
38
29
16
11
1
2
SA
5
RUSKIN
A-36
AHU-5
RETURN
SA
6
RUSKIN
A-60
AHU-6
RETURN
TAPERD
RECT.
36X20
60
5500
-1200
0.28
9
14
32
44
51
47
27
16
1
2
SA
7
RUSKIN
ELBMP5
AHU-7
SUPPLY
RECT.
ELBOW
26X16
30 UP
30 DN
1800
675
0.20
4
8
16
25
25
24
21
17
1
2
SA
8
RUSKIN
ELBMP5
AHU-7
RETURN
RECT.
ELBOW
22X16
30 UP
30 DN
1800
-800
0.20
4
9
17
26
25
24
20
16
1
2
NOTES:
1
CONNECTION SIZES SHALL BE COORDINATED WITH AND MATCH DUCT SIZES.
2
PROVIDE ACOUSTICAL CALCULATIONS FOR AIR SYSTEM TO SHOW THAT NC-40 OR BETTER IS BEING ACHIEVED IN THE SPACES
BELOW IF OTHER THAN BASIS-OF-DESIGN AIR HANDLER OR SOUND ATTENUATOR ARE INSTALLED.
REF DWG M1.3
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/16" = 1'-0"
MA-2/2
F
36x20
2
12Ф
SA
24x30
6
6
5
25
26x16
KITCHEN
119
4
3
5
6
H
8x8
5
14
100
23
12Ф
12Ф
2
UP
EF
15
111
8Ф
108
19
J
4'' DRYER
VENT
12Ф
K
CONF
10Ф
RR
12Ф
12Ф
8Ф
I
1
19
9
16Ф
10Ф
112
16Ф
CUST
FC-3 T
CORR
104
14
21
18
HEALTH
110
9
REF DWG M2.11
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/8" = 1'-0"
MA-2/3
BOYS
203
GIRLS
DATA
202
18x16
16x12
200
AC
10Ф
1
AC
1
202B
2
12Ф
2
(TYP 4)
4'' DRYER
VENT UP
10x10
200
1
200
SPEECH
PSYCH
228
229
12Ф
48x48
3
10Ф
200
(TYP)
4
4
M5.2
SA
1
12Ф
SA
12x12
10Ф
13
J
1
WORK
227
I
10x10
SA
H
18x18
(TYP 3)
4
10Ф
5 22x22
14Ф
14Ф
50x28
13
SA
G
ELEV
SA
LIBRARY
226
K
REF DWG M2.21
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/8" = 1'-0"
MA-2/4
8
9
2
H
I
5
DRYER
VENT
M5.2
RH
10
3
M5.2
J
REF DWG M2.41
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/8" = 1'-0"
MA-2/5
FT
2
1
C
RR
151
RR
154
D
F
SP ED
SP ED
153
3/4"
150
REF DWG M3.12
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/8" = 1'-0"
MA-2/6
10
F
4" CWR
4" CWS
4" HWS
4" HWR
4" UP TO
CHILLER
BOYS
203
3''
G
3/4"
3/4"
3/4"
3/4"
2
9
(TYP)
M5.1
TITLE
206
MECH
205
2''
2" HWR
3''
2" HWS
H
2
1'' HWS/HWR
1 1/2'' CWS/CWR
(TYP. AHU-2,3,4)
3" CWS
3" CWR
3''
OT/PT
230
I
REF DWG M3.21
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/8" = 1'-0"
MA-2/7
C
3/4" HWS
3/4" HWR
2
P
MECH
134
P
1
1 1/2" HWR
1 1/2" HWS
B
1
D
VFD
3
GIRLS
132
3
1" C
D
P
F
VFD
4
B
4
2
BAS
BOILER RELIEF TANK
1" CD
FC
5
ELEV
131
BOILER EPD, (TYP-2)
SEE 1/M7.2.
G
REF DWG M3.23
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
Author
Checker
1/4" = 1'-0"
MA-2/8
4" HWS
2
GIRLS
132
VFD
2
4" CWS
P
P
2
5
4" CWR
VFD
5
D
P
6
BOYS
VFD
1
VFD
6
133
F
REF DWG M3.23
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
Author
Checker
1/4" = 1'-0"
MA-2/9
2
ISOLATION VALVE, TYP
HWS
RECESSED CABINET
UNIT HEATER
STRAINER
PT PORT
MANUAL AIR
VENT, TYP
HWR
3/4" FROM
ABOVE
PIPING WITHIN
CABINET
MANUAL
BALANCING
VALVE
PRESSURE
INDEPENDENT
MODULATING
CONTROL VALVE
SUPPLY AIR
THREADED HOSE
CONNECTION AND
CAP, TYPICAL
FLEX, TYP
UNION, TYP
RETURN AIR
8
CABINET UNIT HEATER PIPING
Scale: NOT TO SCALE
REF DWG M5.1
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/8" = 1'-0"
MA-2/10
2
REMOVABLE CAP FOR CLEANOUT
STAINLESS STEEL VENT
CAP WITH INTEGRAL
BACKDRAFT DAMPER.
SEIHO MODEL RCC-S.
CAP SHALL BE
REMOVABLE FOR
CLEANING. MOUNT 18"
ABOVE ROOF LEVEL
SEAL WATERTIGHT WITH MASTIC
SEE ARCH DWGS FOR FLASHING AND
ROOFING
ROOF
BOOSTER FAN ASSEMBLY
PRESSURE SENSOR
TUBING
4"
DUCTWORK ABOVE
ROOF SHALL BE SEALED
WATER TIGHT AT ALL
JOINTS.
MECH
ACCESS
AREA
LOW VOLTAGE WIRING
BY DIV. 23
REMOTE STATUS
INDICATOR
120V POWER &
PANEL
DISCONNECT BY DIV.
26
WALL
RESIDENTIAL TYPE
CLOTHES DRYER
5
CLOTHES DRYER VENTING DETAIL
Scale: NOT TO SCALE
REF DWG M5.2
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
ADDENDUM #2
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/23/16
MRH
ASD
1/8" = 1'-0"
MA-2/11
3/24/2016 1:10:12 PM
REVISIONS
AHU-6
AHU-1
FM
AHU-5
AHU-7
INSERTION TYPE FLOW METER FOR INPUT TO EMCS.
VENTURI, FLOW MEASURING STATION FOR TAB.
(TYP AT ALL 3-WAY
HEATING VALVES)
5
M5.0
AHU-4
1-1/2"
ABV
1-1/2"
2"
THERMOMETER (TYP), MOUNT WHERE VISIBLE
1"
ABV
ABV
NC
P/T PORTS, TYPICAL.
NO
AHU-3
NC
NO
(TYP AT ALL
3-WAY
COOLING
VALVES)
ABV
(TYP AT ALL 2-WAY VALVES)
ABV
VALVE, BUTTERFLY TYPE
ABV
MANUAL VALVE, SEE SPECS FOR VALVE TYPE
2"
MANUAL BALANCING VALVE
N0
ABV
NC
2"
N0
NC
PRESSURE INDEPENDENT AUTO BALANCING VALVE
2"
ABV
ABV
ABV
ABV
ASME RELIEF VALVE, RELIEF PRESSURE INDICATED.
AUTOMATIC AIR VENTS AT TRAPPED HIGH POINTS.
ROUTE TO RECOVERY TANK.
HWS
HWR
CWS
CWR
1-1/2"
THERMOMETER WELL, COORDINATE LOCATION WITH
CONTROLS CONTRACTOR
3"
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
VAV-405
GENERAL NOTES
FC-2
3"
3/4",
TYP
FC-1
1.
SEE TEMPERATURE CONTROL DIAGRAMS FOR
LOCATIONS AND QUANTITIES OF TEMPERATURE
SENSORS, PRESSURE SENSORS FLOW DEVICES, ETC.
2.
PROVIDE ALL ADDITIONAL DRAINS & CONNECTIONS AS
REQUIRED FOR SYSTEM FLUSHING, CLEANING AND
FILLING.
ABV
ABV
FC-3
FC-4
4"
KEYNOTES
1"
1"
ABV
1"
1
MECHANICAL ROOM PIPING ISOLATION VALVES AND DRAIN
VALVES WITH
HOSE CONNECTION.
2
TEMPERATURE & PRESSURE RELIEF VALVE PROVIDED BY
BOILER MFR.
3
AIR AND DIRT SEPARATOR, PIPE DISCHARGE TO GLYCOL
RECOVERY TANK.
4
SUCTION DIFFUSER W/ STRAINER, DRAIN VALVE, HOSE
CONN., TYP.
5
(NOT USED)
6
GLYCOL FEEDER ASSEMBLY WITH DUAL PUMP AND LOW
LEVEL SWITCH.
ONE ASSEMBLY FEEDS BOTH HEATING AND CHILLED
WATER SYSTEMS.
7
GLYCOL RECOVERY TANK (30 GAL).
8
CONCRETE HOUSEKEEPING PAD, TYPICAL.
9
PRESSURE GAUGE WITH STOP COCK AND SNUBBER.
10
CONCENTRIC REDUCER/INCRESE AT PUMP CONNECTIONS
AS REQUIRED.
11
BYPASS POT FEEDER.
12
PUMP SUPPORT STAND SET ON HOUSEKEEPING PAD WITH
NEOPRENE PADS.
13
SIDESTREAM CARTRIDGE FILTER.
14
CORROSION MONITORING COUPON RACK ASSEMBLY.
15
VENTURI FOR TAB
1"
ABV
HWS
HWR
CWS
CWR
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
3/4",
TYP
ABV
ABV
ABV
ABV
ABV
ABV
ABV
4"
3/4"
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
1-1/4"
1"
ABV
ABV
CU-2
CU-1
ABV
1/2"
ABV
3/4",
TYP
3/4",
TYP
3/4"
ABV
ABV
ABV
VAV-411
ABV
1-1/4"
FC-6
CU-1
HWS
HWR
CWS
CWR
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
ABV
FC-5
FIN-TUBE
(TYP)
PANEL
HEATERS
(TYP)
CH
1
2
TO BUILDING DISTRIBUTION
FS
4"
4"
TO BUILDING DISTRIBUTION
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
4
M5.0
6
M5.0
MECHANICAL SYSTEM DIAGRAMS
2"
AHU-2
ROOF LEVEL
ABV
MECHANICAL ROOM
MECHANICAL ROOM
4"
3
UH-1
3"
3
1
4"
CWR
HWR
4"
HWR
3"
1
4"
4"
AS
1
HWS
4"
1
M5.1
AS
2
3
M5.1
4"
FM
1
CWS
FM
1
HWS
4"
P
4
50 PSIG
50 PSIG
50 PSIG
1"
1"
50 PSIG
4"
15
15
4"
2
TYP
9
9
14
VFD
1
7
TYP
VFD
2
10
10
10
TYP
TYP
VFD
5
1 GPM
TYP
9
9
TYP
7 GPM
TYP
Spokane, Washington
(509) 624-6800
2
VFD
6
10
10
10
TYP
TYP
13 TYP
4
7
M5.1
B
1
HEATING WATER
BOILER (TYP)
B
2
8 TYP
4
4
12
12
8
P
1
8
P
2
2
M5.1
TYP
11
FLTR
1
5
M5.1
13
ET
1
8
6
7
ET
2
4
12
8
P
5
2
M5.1
TYP
11
12
FLTR
1
8
P
6
© 2015 Madsen Mitchell Evenson & Conrad pllc
C:\Users\michael.MEULINK\Documents\Revit Local Projects\15-12 Westgate_ES V16\Westgate ES_Mech-V16 Mike.rvt
4"
4"
4"
15
3/4"
VFD
4
3/4"
P
3
15
4"
3"
VFD
3
4"
4"
Kennewick, Washington
www.mmecarchitecture.com
4"
15
Date:
Drawn by:
Checked by:
Scale:
File No:
03/07/16
NAH
WFM
1/8" = 1'-0"
14.05
Sheet No:
M6.0
1
2
3
D
TABLE STOR
122
¾"
6"RDL UP
F
6"ODL UP
6"DSN-1
@ 18"AFG
3"FS-1
1 1/4"
FREEZER
119A
2"
6"ODL DN
2"
6"RDL DN
3"FS-1
KITCHEN
1 1/4"
2"
2" 1"
119
4
2"
5
1
9
3/4"
¾"
5
P12
P19
¾"
G9
3/4"
1"
P2
3/4"
1
5
P6
1
2
OFFICE/STG.
H
2"
3"FD-1
120
REF: DWG P2.11
Westgate Elementary School
2514 West 4th Ave. Kennewick, WA 99336
Spokane, Washington
(509) 624-6800
Kennewick, Washington
www.mmecarchitecture.com
Unnamed
Date:
Drawn by:
Checked by:
Scale:
Sheet No:
03/28/16
SSW
WFM
1/8" = 1'-0"
PA2/1