Syllabus General Certificate of Education Ordinary Level

advertisement
w
w
e
tr
.X
w
Syllabus
CIE provides syllabuses, past papers, examiner reports, mark schemes and more on the internet.
We also offer teacher professional development for many syllabuses. Learn more at www.cie.org.uk
om
.c
For examination in November 2010
s
er
CDT: DESIGN AND COMMUNICATION 7048
ap
eP
m
General Certificate of Education
Ordinary Level
CDT: Design and Communication 7048 O Level 2010
CDT: DESIGN AND COMMUNICATION
GCE Ordinary Level/SC (7048)
Available In The November Examination Only
INTRODUCTION
The syllabus is designed to lead to an examination for that part of the school curriculum identified as
Design and Communication. It offers an examination for candidates who have followed a course of
study which centrally figures problem-solving design activity involving practical manipulative work
using a range of materials.
AIMS
The aims of the syllabus are the same for all students. The aims set out below describe the
educational objectives of a course in Design and Communication. They are not listed in order of
priority.
-
To foster awareness, understanding, persistence and expertise in those areas of creative thinking
which can be expressed and developed through investigation and research, planning, designing,
realising and evaluating.
-
To encourage the acquisition of a body of knowledge applicable to solving practical/technological
problems operating through processes of analysis, synthesis and realisation.
-
To stimulate the development of a range of appropriate graphical techniques and processes
including model-making.
-
To stimulate the development of a range of communication skills which are central to design,
realisation and evaluation.
-
To encourage students to relate their practical work to their personal interests and abilities.
-
To promote the development of curiosity, enquiry, initiative, ingenuity, resourcefulness and
discrimination.
-
To offer a broad and balanced perspective of the range of technological applications in order to
provide an understanding of their capabilities and limitations.
-
To encourage technological awareness, foster attitudes of cooperation and social responsibility.
-
To stimulate the exercising of value judgements of an aesthetic, technical and economic nature.
1
CDT: Design and Communication 7048 O Level 2010
SCHEME OF EXAMINATION
Candidates must take papers 1 and 2
Paper 1 (2¾ HOURS)
The time allowed for this paper includes fifteen minutes reading time. The paper will be divided into
two sections. The first section will require in-depth application of a variety of skills and the second will
require candidates to apply reasoned consideration to direct problems of graphic communication.
Candidates answer one question from a choice of two in Section 1.
maximum of 30 marks.
Each question carries a
Candidates answer two questions from a choice of four in Section 2.
maximum of 25 marks.
Each question carries a
Paper 2
Candidates will select a problem from the themes set by CIE during the year preceding the
examination. The investigative folio, answering a problem selected from the themes, will be compiled
by the candidate during a period of two terms. All evidence of problem solving and realisation will be
contained in the folio. The maximum size of the folder should be A3.
Teachers may direct as much time as they wish for candidates to investigate their chosen theme.
Candidates may seek help and guidance from their teacher as their investigation develops. Colour
should be used where appropriate to aid clarity and presentation.
The folios will be marked by the candidates' teacher who will use the criteria given at the end of this
syllabus. The forms necessary for the recording of marks are included at the end of this syllabus.
Details regarding external moderation of coursework can be found on page 10.
Paper
Type of paper
1
Written paper
2
Teacher-assessed coursework (Project)
2
Duration
Weighting
2¾ h
70%
-
30%
CDT: Design and Communication 7048 O Level 2010
SYLLABUS CONTENT
Candidates should have experience of working with the following conventions:
PD 7308 Engineering Drawing for schools and colleges.
PD 7307 Graphic symbols for use in schools and colleges.
PD 7303 Electrical and electronic graphical symbols for use in schools and colleges.
BS 1192 Recommendations for building drawing practical.
BS 4058 Data processing flowchart symbols, rules and conventions.
Candidates should be able to:
Orthographic projections
-
give information or use given information in
both first and third angle projection.
Dimensions and drawings of detail and simple
assemblies of parts from information given in
orthographic or pictorial form will be required,
including parts lists.
Sectional views
-
select the most suitable section, draw whole
or part sections taken on the principle vertical
and horizontal planes.
Sketching
-
understand and produce free-hand sketches
which communicate ideas, thoughts and
information from written, visual or tabular data,
and presented in pictorial, formal pictorial,
plane or orthographic modes.
Interpretation of Information
-
read drawings and interpret given information.
Division
-
divide lines and angles.
Geometrical figures
-
understand the use of an appropriate
geometrical construction in order to draw:
regular plane linear shapes (triangles,
quadrilaterals, pentagons, hexagons and
octagons).
The circle
-
understand parts of a circle and use
appropriate geometrical construction in order
to draw: circles, tangents and tangential arcs.
Ellipse
-
construct ellipses by an accurate method.
(Trammels will be permitted.)
Loci
-
draw the paths of points in the manner of
simple plane mechanisms. Linkages will have
a maximum of four elements.
Presentation
-
demonstrate use of shading, colouring and
other techniques for emphasis.
apply an understanding of light, shade and
shadow to give increased credibility to pictorial
drawing.
communicate the material and surface finish
of a given product.
-
3
CDT: Design and Communication 7048 O Level 2010
Isometric
-
produce isometric views of circles and arcs.
Isometric scales will not be required.
Planometric
-
produce planometric views of circles and arcs.
No scaling will be required.
Perspective
-
produce estimated perspective drawings using
one or two vanishing points.
Oblique
-
draw oblique views of circles and arcs (both
cavalier and cabinet).
Exploded views
-
draw exploded views of objects in line along
one axis only. In the examination paper,
however, information may be presented on
more than one axis.
Use of drafting aids
-
use drawing aids to develop good drafting
techniques. Radius aids, flexi curves, ellipse
aids, nut templates will be permitted in the
examinations unless stated otherwise in
particular questions.
During their course
candidates should have experience in the use
of technical pens, templates, lettering and
other stencils.
Geometrical loci
-
draw the linear helix, the cycloid and simple
plate cams (uniform velocity and retardation).
Developments
-
draw developments of right prisms, cylinders,
pyramids
and
cones
(complete
and
truncated).
Intersections
-
produce views of simple prisms and cylinders
intersecting at right angles with axes in line.
Auxiliary views
-
draw objects in first auxiliary views at set
square angles (30°, 45° and 60°) including
true shape of cut surfaces.
Convey information
-
construct and interpret histograms, pie
diagrams, bar charts and graphs from data
provided in a tabular or matrix form to
communicate quantity and distribution.
Candidates will be expected to produce flow
charts to describe processes, operations or
assemblies.
Analysis of products
-
analyse the construction and operation of
uncomplicated products.
research, analyse and consult relevant
sources of information.
recognise factors that will determine the
preparation of a viable specification.
synthesize and communicate proposals for
solutions.
-
4
CDT: Design and Communication 7048 O Level 2010
Control
-
5
understand that most activities require some
sort of control.
understand the term control system.
understand that in order for a system to work
it needs an INPUT CONTROL and OUTPUT.
make use of the systems approach when
designing solutions to control problems (the
systems approach is to be used to explain a
control situation without going into detail of
how it is to be done).
CDT: Design and Communication 7048 O Level 2010
NOTES FOR GUIDANCE
In the areas of product analysis and control the most complex items that candidates would be
expected to have experience of would be things such as:
a torch,
a bicycle,
a manually operated camera,
a small pocket radio.
It should be noted that knowledge about specific products will not be required in the terminal
examinations but candidates will be expected to show their ability to analyse products as part of their
project work.
It is not the intention that specific items in the areas listed below should be identified but rather that
examples based on them should be used as a way of teaching and applying the knowledge and skills
developed as a result of studying the core content of the syllabus.
The following lists offer suggestions for areas of study but they should not be considered definitive:
Signs
Symbols and logos
-
-
on control panels
directional
in shops
in streets
on clothes
on instruments and control panels
on maps
on products
on road signs
in vehicles
used by companies and organisations
Packaging – candidates should be familiar with packaging used in ways such as the following:
-
to protect items
to communicate information about a product
to advertise and help sell products
Examples of items to be packaged might include:
-
food
cosmetics
toys
small gift items
small electrical products
records, tapes and CDs
Lines and planes in projection – this area is covered by the sections on auxiliary views and
orthographic projection.
6
CDT: Design and Communication 7048 O Level 2010
ASSESSMENT CRITERIA FOR PROJECT
This paper presents the candidate with a number of problematic themes. The questions which pose
these problems are open-ended with a low level of directiveness. The candidates should have a good
deal of freedom to determine the length and nature of their involvement with each element required in
this high level design/problem solving process.
(a) Problem identification
The candidates interpretation of the problem presented in a statement,
i.e. the brief
Marks
The candidate has:
failed to identify a suitable problem.
0
either (i) needed help to identify a problem, or (ii) had no help but the resulting
problem is unsuitable for design development.
2
identified and described unaided a problem appropriate for design
development.
5
Maximum marks available in this section:
5
(b) Research and analysis
The orderinq of information relevant to the presentation of a solution
The candidate's research:
consists of copied material, without any evident purpose.
3
has not been initiated independently, or is incapable of forming a planned programme
or the candidate has required considerable assistance and frequent direction.
6
has required significant initial assistance; thereafter little direction has been needed but
the candidate has either concentrated on a narrow area or given only shallow attention to
a wider field.
9
is well planned, broad and imaginative. The candidate has developed a programme
without assistance and this has resulted in information being structured and
effectively communicated.
15
Maximum marks available in this section:
15
7
CDT: Design and Communication 7048 O Level 2010
(c) Specification for a possible solution
The candidate's recognition of those particular factors in research that will determine a
specification for presenting a possible solution.
Marks
The candidate's specification:
is not evident.
0
is very shallow.
2
is vague, not specific to the problem.
4
is not wholly specific, containing some irrelevant material.
6
is specific, but does not completely identify on all the constraints imposed in the problem.
8
is concise, definitive, and is drawn up with obvious reference to the preceding research
and analysis.
10
Maximum marks available in this section:
10
(d) Proposals for a solution
The synthesis and communication of a number of proposals for a solution.
The candidate's response in this area:
is limited to a single unsupported proposal, the communication of which was
largely effective.
5
is limited to a single proposal which is quite well supported and communicated in a
reasonable manner; or a number of largely unsupported and similar proposals
communicated in an uneffective manner.
10
consists of a number of distinct proposals which are unsupported and communicated
in an ineffective manner.
15
consists of a number of distinct well-supported proposals which are communicated in
an effective manner.
20
Maximum marks available in this section:
20
8
CDT: Design and Communication 7048 O Level 2010
(e) Realisation
The realisation and presentation of a final solution.
Marks
The candidate's solution:
is obviously not a viable solution but is recognisable as an attempt to define a solution.
8
is recognisable as a solution but can easily be faulted in respect of ideas, communication
and quality or because it fails to meet the specification.
16
is incomplete and requires additional material to meet the specification in full, but has
been presented in a form which is easily understood.
24
is substantially free of omission and for the most part fulfils the specification. It has
been presented in a clear, descriptive manner.
32
is well conceived, clearly and attractively defined and fully satisfies the specification.
40
Maximum marks available in this section:
40
(f) Evaluation
Evaluation of the solution, considering the factors raised in (c).
The candidate's evaluation is:
for the most part irrelevant.
2
superficial.
4
an honest attempt to appraise the solution but lacks objectivity providing only
unsupported judgement.
6
almost complete, consisting of some unsupported judgement.
8
thorough, objective, relevant and concise and provides useful material capable of
further development.
10
Maximum marks available in this section:
10
Maximum marks available:
100
9
CDT: Design and Communication 7048 O Level 2010
External Moderation for Centres in Mauritius
External moderation of internal assessment will be carried out by moderators appointed by the
Mauritius Examinations Syndicate on behalf of CIE. A representative sample will then be sent to CIE
by the Mauritius Examinations Syndicate once in-country moderation is complete.
External Moderation for all other Centres
External moderation of internal assessment will be carried out by CIE.
The internally moderated marks for all candidates must be received at CIE by 31 October for the
November examination. These marks may be submitted either by using MS1 mark sheets or by using
Cameo as described in the Handbook for Centres.
Once CIE has received the marks, CIE will select a sample of candidates whose work should be
submitted for external moderation. CIE will communicate the list of candidates to the Centre, and the
Centre should despatch the coursework of these candidates to CIE immediately. Individual Candidate
Record Cards and Coursework Assessment Summary Forms (copies of which may be found at the
back of this syllabus booklet) must be enclosed with the coursework.
Further information about external moderation may be found in the Handbook for Centres and the
Administrative Guide for Centres.
All records and supporting written work should be retained until after the publication of the
results.
10
CDT: DESIGN & COMMUNICATION (7048/2)
COURSEWORK ASSESSMENT FORM
GCE SC and O Level
Please read the instructions overleaf before completing this form.
Centre Number
Candidate
Number
Centre Name
November
Teaching
Group/Set
Candidate Name
(a)
(b)
Problem
Research
Identification & Analysis
(max 5)
(max 15)
(c)
Specification
for Solution
(max 10)
2
(d)
(e)
(f)
Total Mark
Proposals Realisation Evaluation
for Solution
(max 20)
(max 40)
(max 10)
(max 100)
Internally
Moderated
Mark
(max 100)
11
Teacher completing this form (BLOCK CAPITALS)
Date
Name of Moderator (BLOCK CAPITALS)
Date
WMS401
7048/2/CW/S
A.
INSTRUCTIONS FOR COMPLETING COURSEWORK ASSESSMENT SUMMARY FORMS
1.
Complete the information at the head of the form.
2.
List the candidates in an order which will allow ease of transfer of information to a computer-printed Coursework mark sheet at a later stage (i.e. in candidate index number order,
where this is known; see item B.1 below). Show the teaching group or set for each candidate. The initials of the teacher may be used to indicate group or set.
3.
Enter each candidate’s marks on this form as follows:
4.
B.
(a)
There are columns for individual skills; enter the marks initially awarded (i.e. before internal moderation took place).
(b)
In the column headed ‘Total Mark’; enter the total mark awarded before internal moderation took place.
(c)
In the column headed ‘Internally Moderated Mark’, enter the total mark awarded after internal moderation took place.
Both the teacher completing the form and the internal moderator (or moderators) should check the form and complete and sign the bottom portion.
PROCEDURES FOR EXTERNAL MODERATION IN MAURITIUS
1.
University of Cambridge International Examinations (CIE) sends computer-printed Coursework mark sheets (MS1) to the Mauritius Examinations Syndicate in early October
showing the names and index numbers of each candidate.
2.
External moderation of internal assessment will be carried out by moderators appointed by the Mauritius Examinations Syndicate on behalf of CIE.
12
The Mauritius Examinations Syndicate will communicate with Centres regarding procedures regarding external moderation and sampling.
It is the responsibility of the Mauritius Examinations Syndicate to ensure that the final moderated marks are recorded on the computer-printed Coursework mark sheets (MS1).
C.
PROCEDURES FOR EXTERNAL MODERATION IN THE REST OF THE WORLD
1.
University of Cambridge International Examinations (CIE) sends a computer-printed Coursework mark sheet (MS1) to each centre in early October for the November examination
showing the names and index numbers of each candidate. Transfer the total internally moderated mark for each candidate from the Coursework Assessment Summary Form to
the computer-printed Coursework mark sheet (MS1).
2.
The top copy of the computer-printed Coursework mark sheet MS1 must be despatched in the specially provided envelope to arrive as soon as possible at CIE but no later than
31 October for the November examination.
3.
CIE will select a list of candidates whose work is required for external moderation. As soon as this list is received, send the candidates’ work with the corresponding Individual
Candidate Record Cards, this summary form and the second copy of MS1 to CIE. Indicate the candidates who are in the sample by means of an asterisk (*) against the
candidates’ names overleaf.
4.
CIE reserves the right to ask for further samples of Coursework.
5.
Send, with the sample work, instructions given to candidates and information as to how internal moderation was carried out.
7048/2/CW/S
Download