w
w
ap
eP
m
e
tr
.X
w
7040/01
Paper 1
May/June 2003
2 hours 40 minutes
Additional Materials:
A2 Drawing paper (1 sheet)
Standard drawing equipment
READ THESE INSTRUCTIONS FIRST
Print your name, Centre number and candidate number at the bottom right-hand corner of your drawing
paper.
Answer five questions.
Answer not more than three questions from any one section.
Unless otherwise stated, strictly geometrical methods must be used, solutions are to be drawn full size and
no dimensions are required. All construction lines must be shown clearly, but lines which are parallel to,
perpendicular to or inclined at angles of 30 °, 45 ° or 60 ° to other lines may be drawn without showing
construction lines.
Use both sides of the drawing paper for your answers.
The number of marks is given in brackets [ ] at the end of each question or part question.
All dimensions are in millimetres unless otherwise stated.
This document consists of 9 printed pages and 3 blank pages.
SP (SC) S35564/2
© CIE 2003
[Turn over
om
.c
GEOMETRICAL AND MECHANICAL DRAWING
s
er
CAMBRIDGE INTERNATIONAL EXAMINATIONS
General Certificate of Education Ordinary Level
2
Section 1 Plane Geometry
Answer not more than three questions from this section.
(a) (i)
(ii)
Construct the triangle ABC shown in Fig. 1.
[4]
Reduce the triangle ABC to a square having a similar area. Measure and state the length
of side of the square to the nearest mm.
[11]
(b) A piece of thin wire, 170 mm long, is formed into a triangle. Construct the triangle whose
sides are in the ratio of
2.8 : 4.3 : 5.6
[5]
A
45°
60
1
C
B
80
Fig. 1
7040/01 Jun03
3
Fig. 2 represents the diagrammatic arrangement of a mechanism in which O is a fixed centre
about which a disc of radius OA rotates. The rigid link BE is attached to the disc and the rigid link
CB by pivot joints at A and B.
A fixed point S allows link BE to pivot and slide as OA rotates. Simultaneously C is constrained to
reciprocate along the R110 arc.
(a) Draw, full size, the locus of the point P when OA makes one complete revolution.
[18]
(b) State, to the nearest mm, the maximum and minimum distance that end E moves with respect
to the fixed point S.
[2]
B
P
AO = 30
AB = 80
BC = 110
BP = 40
AE = 135
C
A
O
95
R110
30
2
S
60
20
E
Fig. 2
7040/01 Jun03
[Turn over
4
Fig. 3 shows details of an aluminium handrail bracket.
Draw, full size, the given view of the bracket, clearly showing all construction and points of
tangency.
[20]
80
R8
5
Ø30
Ø40
0
R7
5
R2
A
150
Tangent to
ellipse at C
C
30
3
B
8
Curve AB is quarter of an ellipse
major axis = 200
minor axis = 90
Fig. 3
7040/01 Jun03
5
Section 2 Solid Geometry
Answer not more than three questions from this section.
Fig. 4 shows two views of a roof drawn to a scale of 1:100. An electric cable runs from A to three
lights at R, S and T on the surface of the roof.
(a) (i)
(ii)
Draw the two given views.
[2]
Show, on these views, the position of the electric cables, which in each case appear to
be straight lines across the roof in the plan view.
[3]
(b) Determine and state the length of each piece of cable in metres.
[15]
80
35
70
25
a'
60°
5
75°
25
s'
t'
r'
5
10
r
s
70
a
25
4
t
Fig. 4
7040/01 Jun03
[Turn over
6
Fig. 5 shows two views of a retaining clip in first angle projection. Ignoring the thickness of the
material:
(a) draw, full size, the given views;
[2]
(b) project an auxiliary plan from the given elevation onto the ground line X1Y1 when looking in
the direction of arrow B;
[9]
(c) from your auxiliary plan (b) project an auxiliary elevation onto the X2Y2 line when looking in
the direction of arrow A.
[9]
B
30
60°
5
Y2
X2
R20
30°
X1
5
5
80
30°
Y1
60°
A
Fig. 5
7040/01 Jun03
30
7
Fig. 6 shows details of a cylindrical pipe intersecting a semi-circular piece. Ignoring the thickness
of the material.
Draw, full size:
(a) the given views;
[2]
(b) a plan view that includes the curve of intersection and all hidden detail;
[12]
(c) the development for the semi-circular piece AB. Include the true shape of the hole.
60
30°
[6]
20
A
0
R4
Ø60
6
B
45
45
Fig. 6
7040/01 Jun03
[Turn over
8
Fig. 7 shows details of the blank for a threaded coupler. When complete, the blank has a left and
right hand square thread machined at opposite ends.
Draw the coupling, full size, showing both threaded portions.
Hidden detail is not required.
[20]
LH sq thread
pitch of 40
Ø80
Ø40
RH sq thread
pitch of 40
Ø80
7
60
15
Fig. 7
7040/01 Jun03
60
9
Details of a moulded block are shown in Fig. 8.
Draw, full size, an isometric projection of the block with C in the forefront of your view. Omit hidden
detail and do not use an isometric scale.
[20]
45
20
25
45
25
35
C'
R40
25
C
110
R20
95
8
15
Fig. 8
7040/01 Jun03
10
BLANK PAGE
7040/01 Jun03
11
BLANK PAGE
7040/01 Jun03
12
BLANK PAGE
7040/01 Jun03