For ConTech Lighting RL4_MH, RL6_MH and RL8_MH Series Recessed Metal... INSTALLATION PROCEDURES

For ConTech Lighting RL4_MH, RL6_MH and RL8_MH Series Recessed Metal Halide Housings
JOIST: 2" x 8"
Housing can NOT be installed in direct contact with insulation. Do not install
insulation within 3" of fixture sides or wiring compartment, nor above fixture
in such a manner to entrap heat. (Figure 1)
Install hanger bars to fixture, ensure end tab is facing outward. (Figure 2)
Extend bar hangers to fit between joists and position fixture temporarily by
hammering nail on bars into the joists. Hangers should be level with bottom
of joists (Figure 3). Locate center of fixture opening in the ceiling sheetrock
and cut a 5" hole for 4" fixtures, a 6-1/2" hole for 6" fixtures, or a 8-1/8"
hole for 8" fixtures.
Locate proposed fixture center in ceiling tile and cut a 6-1/2" hole for 6"
fixtures, or a 8-1/8" hole for 8" fixtures. Place ceiling tile in T-Bar grid. Place
fixture into position and snap bar hanger foot with integral T-bar clips onto
T-bars (Figure 4). Secure hanger bars to T-bars and properly support the
fixture from the building structure. Note: Op-tional T-Bar Clips and screws
may be used as local code authority or site conditions require. To secure
fixture position in ceiling, squeeze tabs into hanger bars.
Nail In Tabs
Remove J-box cover by pushing up on spring clip. Attach conduit with
connector to J-box and secure. Connect supply wires to fixture wires and
insulate with proper size wire nuts (not provided). Connect black to black
(hot), white to white (neutral), and green to green (ground). After splicing is
completed, insert wires carefully into junction box. Replace cover.
If the ballast is not working properly, replace with the same ballast type.
Make sure that power to the fixture is off. Remove lamp. Pull trim and drop
the reflector from housing frame. Remove J-box cover with ballast attached
by pushing up on spring clip. Disconnect the ballast from input wiring and
lampholder leads (leads are terminated by wire nuts, or push to release
connectors on the ballast). Replace ballast with a factory approved ballast.
Resinstall ballast/J-box cover.
Bar Hanger
Use only those trims, lamps and maximum wattages proper for this fixture,
as indicated on the label within the housing. Do not exceed maximum
wattage lamp shown for each trim.
The National Electrical Code, Article 110-3(B), states that “Listed or labeled
equipment shall be used or installed in accordance with any instructions
included in the listing or labeling.” Use only with Con-Tech UL listed trims.
Use of other trims not listed in this fixture, including those that are UL classified, is a violation of N.E.C. 110-3(B) and voids all warranties.
• Read all the instructions before installation. Save instructions for later use.
• Turn off power at fuse or circuit breaker box before installation or before
doing any maintenance work.
• Product must be grounded to avoid potential electric shock and any other
potential hazards.
• Product must be mounted in locations and at heights and in a manner
consistent with its intended use, and in compliance with National Electrical
Code and local codes. Use of accessory equipment is not recommended.
• Installing contrary to instructions may cause unsafe conditions.
• Do not block light from the trim aperture, in whole or in part, as this may
cause unsafe conditions.
• Warning: Risk of fire. Most dwellings built before 1985 have supply wire
rated at 60°C. Consult a qualified electrician before installation.
• To avoid hazards to children, account for all parts and properly dispose of
all packing materials.
• Call the Technical Support department at ConTech Lighting with any
installation questions: 847.559.5500.
Optional T-Bar Clip
Note: Tighten screw to secure
hanger bar to T-Bar
Bar Hanger
White to White
Black to Black
Ground Wire
All specifications subject to change without notice.
This document can be recycled
Related flashcards


28 cards

Electrical engineering

45 cards


13 cards

Signal processing

22 cards

Electrical components

22 cards

Create Flashcards