A
B
C
A
B
D.
C
E.
TYPE 1
F.
19
19
F2
F2
F2
EXISTING TRACK TO REMAIN,
PROVIDE NEW HEADS
EXISTING TO REMAIN
10' - 0"
10' - 0"
21
21
F18
F15
17
F1
F13
GENERAL: OVERSIZED PENDANT
E
1.
F18
F4
HI-LITE MFG. H-23638 ARIES COLLECTION
LINE OF NEW TRACK FOR SECURITY GATE. REFER TO
SPECIFICATION SECTION 08 3513 FOLDING SECURITY
GRILLES.
MATCH HEIGHT OF NEW CEILING TO EXISTING CEILING
HEIGHT.
PROVIDE SOFFIT COMPRISED OF 3-5/8" METAL STUD WITH
RUNNER CHANNELS AT 16"O.C. AND 1 LAYER OF GYPSUM
BOARD. TAPE, SPACKLE, AND FINISH AS SCHEDULED.
HEIGHTS AS INDICATED.
PROVIDE STAINLESS STEEL EXTENSION TO TOP OF HOOD TO
EXTEND TO FINISHED CEILING TO CONCEAL ALL DUCT
WORK AND SUPPORTS. COORDINATE WITH MILLWORK TO
ENSURE FIT.
HEAT LAMPS MUST BE CENTERED OVER EQUIPMENT BELOW.
COORDINATE WITH MILLWORK AND KITCHEN EQUIPMENT
CONTRACTOR.
EXISTING CEILING TO REMAIN. PATCH IN GWB BOARD TO
MATCH EXISTING. TAPE, SPACKLE, AND FINISH BOUNDARY
BETWEEN OLD AND NEW WORK.
EXISTING HOOD. CLAD AS INDICATED, REFER TO DETAILS.
2.
3.
F18
TYPE 7
EXISTING TRACK TO
REMAIN, PROVIDE
NEW HEADS
F15
4.
F12
F18
F13
F14
F13
5.
F18
F15
6.
F18
F16
F15
7.
F14
F16
12
F12
F13
F13
F16
CYLINDRICAL PENDANT, CABLE MOUNT
F6
COOPER LIGHTING
S
TE
C N
RK
No.
16419
R E D A RC H
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
LINEAR PENDANT LIGHT
F7
TECH LIGHTING KNOX LINEAR SUSPENSION
PENDANT LIGHT OVER SEATING
F8
HI-LITE MFG. H-MCGUS-6S - TELESCOPIC
BARN LIGHT WALL SCONCE - TOWER
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
F9
F18
F15
HI-LITE MFG. H-18110 ANGLE SHADE w/ WALL MOUNT
F13
F16
11
NEW
OF O J
BARBICAN - ROUND DRUM 16-3160
F14
15
F18
F12
BARN LIGHT WALL SCONCE - HIGH CEILING
F18
F12
EXISTING TRACK TO
REMAIN, PROVIDE
NEW HEADS
F18
F18
F10
HI-LITE MFG. H-LCGU-FB VAPOR JAR
F15
TYPE
1
PENDANT OVER BAR SEATING
F11
HI-LITE MFG. H-1214 ARIAL
GWB CEILING
3-5/8" METAL STUD W/ 5/8" GYPSUM WALL BOARD,
FINISHED & PAINTED AS SPECIFIED
DECORATIVE PENDANT OVER SERVERY MILLWORK
F18
8
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
CEILING TYPES - BASIS OF DESIGN
REFER TO SPECIFICATION SECTION 09 5100 FOR INFORMATION.
8
SEALED:
KEYED NOTES
F15
12
BARBICAN - SQUARE DRUM 16-5048
F5
F13
16
TYPE 1
LARGE PENDANT IN HIGH CEILING
F3
F12
F16
F14
I-405
COOPER LIGHTING - PORTFOLIO
F12
F1
16
GENERAL: 6" LED RECESSED CAN
F2
LARGE PENDANT OVER ROUND BOOTH
F1
F1
7
J.
K.
COOPER LIGHTING - PORTFOLIO
I
17
I.
F1
R EG
3
I-250
0"
R 3' -
F18
F1
R
9'
F1
F1
GENERAL: 4" LED RECESSED CAN
N
-0
"
F1
F1
H.
REFER TO SPECIFICATION SECTION 09 5100 CEILINGS FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 09 2116 GYPSUM
BOARD ASSEMBLIES FOR ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING.
REFER TO MECHANICAL DRAWINGS FOR DUCT WORK
INFORMATION.
REFER TO FIRE PROTECTION DRAWINGS FOR ADDITIONAL
INFORMATION ON SPRINKLER SYSTEM.
ALL WIRE SUPPORTS THAT WILL BE VISIBLY EXPOSED ARE
TO BE USG 1/32" MULTI STRAND AIRCRAFT CABLE WITH
LOOP AND CRIMP END CONNECTION UNLESS OTHERWISE
NOTED. VERIFY WITH ARCHITECT IN FIELD.
USE COLOR MATCHED PLASTIC GROMMET FOR ALL
PUNCTURES IN CEILING SURFACES.
CALCULATE WEIGHTS AND LOADS OF SUSPENDED AND
OVERHEAD ELEMENTS AND SUPPLY AND INSTALL WEIGHT
TEST AND LOAD RATED STRUCTURAL COMPONENTS,
CONNECTIONS AND ASSEMBLIES TO INSURE PROPER
CODE COMPLIANT AND SUFFICIENT STRUCTURAL
SUPPORT AND CAPACITY.
PATCH AND REPAIR EXISTING GWB CEILINGS AS A RESULT
OF REMOVAL OF EXISTING LIGHT FIXTURES AND/OR
MECHANICAL EQUIPMENT.
ALL NEW AND EXISTING GWB CEILING TO BE PAINTED IP-4.
ANY EXPOSED STRUCTURE TO BE PAINTED IP-8.
SEY
ER OR
F1
F1
F1
G.
F18
21
TYPE 1
F1
HEAT LAMPS, REFER TO
EQUIPMENT PLAN
EXISTING TRACK TO REMAIN,
PROVIDE NEW HEADS
21
F1
9' - 0"
6' - 0"
F2
FIXTURE TYPES
CT
C.
GENERAL NOTES
TE
B.
LIGHTING PLAN
MA
A.
CEILING PLAN
S TAT
3/23/2016 6:22:07 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
F12
HI-LITE MFG. H-2046 MINI PENDANT, CORD MOUNT
OPEN STRUCTURE, PAINTED
TYPE
4
2
COLOR TO BE SELECTED
DRAWN BY:
AGK
CHECKED BY:
AGK
DECORATIVE PENDANT OVER SERVERY MILLWORK
F13
HI-LITE MFG. H-7106 MINI PENDANT, CORD MOUNT
DECORATIVE PENDANT OVER SERVERY MILLWORK
TYPE
4
ADD/ALT 1
1/8" = 1'-0"
LIGHTING PLAN - ADD/ALT
GRID: ARMSTRONG 15/16" STANDARD PRELUDE XL
1/8" = 1'-0"
TILE: EXPANDED METAL, 2' x 2' ARMSTRONG
METALWORKS MESH - WOVEN WIRE - 6129AM
DECORATIVE PENDANT OVER SERVERY MILLWORK
F15
TYPE
4
5
HI-LITE MFG. H-16006 MINI PENDANT, CORD MOUNT
GRID: ARMSTRONG
USG PARALOCK
15/16"
SYSTEM
STANDARD PRELUDE XL
DECORATIVE PENDANT OVER SERVERY MILLWORK
F16
TYPE
4
6
DECORATIVE WOOD CLOUD WITH LIVE EDGE
WOOD ATTACHED TO STEEL SQUARE EXTRUSION
HI-LITE MFG. H-19006 MINI PENDANT, CORD MOUNT
MILLWORK
DECORATIVE PENDANT OVER SERVERY MILLWORK
2' -
"
8 3 /4
2"
PAINTED 5/8" GYPSUM WALL
BOARD ON 3 5/8" 20 Ga. METAL
STUDS FRAMING @ 16" O.C.
ATTACHED TO DECK ABOVE w/
THREADED ROD. REFER TO DETAIL
STAINED SOLID WOOD PLANKING
w/ VARIABLE WIDTHS, DEEPS, &
LENGTHS. COORDINATE w/
ARCHITECT FOR SIZES & FINISH.
2"
4"
6"
R 5' R 8' - 0"
TYPE 6 CEILING CONSISTS OF:
LIVE EDGE VENEER BONDED PANELS.
NATURAL OAK SPECIES.
FINISHED WITH I-TR-W COATING IN COLOR TO BE SELECTED.
CLASS A FIRE RATED.
SQUARE EDGES TO BE EDGE BANDED WITH LIKE EDGING.
MAINTAIN APPROXIMATELY 2" GAP BETWEEN BOARDS.
MATCH EXISTING CONDITION IN RETAIL DINING.
TYPE
4
7
HI-LITE MFG. H-EMC-06 MINI PENDANT, CORD MOUNT
F18
TRACK HEAD REPLACEMENT FOR EXISTING LIGHTOLIER
LINE VOLTAGE SYSTEM
SIMILAR TO PHILLIPS LIGHTING LED TRACK HEAD
(FIXTURE MUST BE COMPATIBLE WITH EXISTING TRACK)
DECORATIVE SOLID WOOD STICK CEILING
ATTACHED TO STEEL SQUARE EXTRUSION
MILLWORK
TYPE 7 CEILING CONSISTS OF:
NATURAL MAPLE SPECIES.
FINISHED WITH I-TR-W COATING IN COLOR TO BE SELECTED.
CLASS A FIRE RATED COATING.
5"
2"
4"
BOARDS TO RANGE IN
THICKNESS FROM 1/2" - 2"
THICK
F17
GENERAL NOTES
31
/ 8"
A.
2"
B.
4"
C.
ABBREVIATIONS
4"
D.
4"
4"
4"
4"
2"
5"
3 3/4
"
2"
ACT:
GWB:
2"
7
I-405
ACOUSTICAL CEILING TILE
GYPSUM WALL BOARD
E.
F.
G.
H.
I.
2"
J.
2"
2"
4" CURVED CHANNEL, PAINTED. SUSPENDED FROM
GYPSUM CEILING CLOUD ABOVE w/ THREADED ROD
& BEAM CLAMPS
K.
L.
M.
3
RCP - ADD/ALT - WOK
1/2" = 1'-0"
REFER TO ELECTRICAL PLANS AND SPECIFICATIONS FOR
INFORMATION ON FIXTURES, CONNECTIONS, SWITCHING,
ETC.
REFER TO PLAN DRAWINGS FOR ADDITIONAL DETAILS ON
FOOD STATION CEILING SYSTEMS.
COORDINATE LIGHT FIXTURE HEIGHTS WITH ARCHITECT
PRIOR TO INSTALLATION.
COORDINATE HOOD LOCATIONS WITH MECHANICAL
DRAWINGS.
REFER TO ELECTRICAL DRAWINGS FOR ADDITIONAL
INFORMATION.
PROVIDE COLOR MATCHED SPACER BETWEEN TRACK
SYSTEM AND OVERHEAD CONSTRUCTION.
LIGHTING COLOR TO BE 3000K.
ARCHITECT TO SELECT ALL LIGHT FIXTURE FINISHES.
COORDINATE TRANSFORMER CONCEALMENT WITH
SECTIONS AND DETAILS. REVIEW FINAL LOCATION WITH
ARCHITECT.
CONTRACTOR TO COORDINATE THE INSTALLATION OF
LIGHTING ON MILLWORK ELEMENTS. ELECTRICAL FEEDS,
BOXES & SUPPORT STRUCTURES ARE TO BE CONCEALED
WITHIN OR BEHIND MILLWORK. FULL COORDINATION
BETWEEN ELECTRICAL CONTRACTOR & MILLWORK
PROVIDER IS REQUIRED.
LIGHTING & OVERHEAD CANOPIES ARE NOT TO
INTERFERE IN ANY WAY WITH INSTALLATION OF
OPERATION OF FIRE PROTECTION SYSTEMS.
PROVIDE LED LAMPS WHERE POSSIBLE FOR ALL
INCANDESCENT SOCKETS.
LAMPS OVER FOOD SERVICE MUST BE PROVIDED WITH
SHATTER PROOF GLASS.
RAMAPO COLLEGE
OF NEW JERSEY
ADD/ALT 1
2
REFLECTED CEILING PLAN - ADD/ALT
HI-LITE MFG. H-15006 MINI PENDANT, CORD MOUNT
SERVERY CEILING
1
TILE: 2x2 SMOOTH FINISH
ARMSTRONG ULTIMA LAY-IN
SCOTT STUDENT CENTER
RESIDENTIAL DINING
F14
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
I-250
PHASE 2: ALTERATIONS & ADDITIONS
GRID: ARMSTRONG 15/16" STANDARD PRELUDE XL
RCNJ No. 2014-37-01C
TILE: 2x2 SCRUBBABLE AND SOIL RESISTANT
ARMSTRONG CERAMAGUARD LAY-IN
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
TYPE
4
3
3/23/2016 6:22:13 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
TOILET ROOMS
M
N
TOILET ROOM GENERAL NOTES
8' - 3"
A.
TA-6
20
TA-8
MEN
131
TA-8
TA-5
TA-2, TA-3
14
I-300
TA-4
6
S-3.1B
0
S-3.1B
0
I-300
TA-4
TA-5
S-3.1B
0
17
S-3B
0
S-3B
0
8
19
I-300
S-3.1B
0
S-3B
0
5' - 1 1/4"
8' - 0"
S-2.1
0
109
S-3.1B
0
S-3.1B
0
7.
8.
9.
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
ALIGN
3' - 6 1/4"
DECORATIVE WALL
TILE OVER 1/2"
CONCRETE BACKER
BOARD, REFER TO
I-102 FOR FINISH
INFORMATION
DECORATIVE WALL
TILE OVER 1/2"
CONCRETE BACKER
BOARD, REFER TO
I-102 FOR FINISH
INFORMATION
SCHLUTER QUADEC (OR
SIM.) CORNER GUARD,
FINISH TO BE SELECTED
110
15
15
2' - 3"
3' - 0"
3' - 0"
2' - 3"
2
TOILET ROOMS - NOTED
11 1/8"
18
13
TOILET ROOM - PD 3
1 1/2" = 1'-0"
TOILET ROOM - PD 1
1 1/2" = 1'-0"
>TR-4:
TOILET PARTITION
MATERIAL: CORIAN SOLID SURFACE
COLOR: TO BE SELECTED
FIELD VERIFY ALL DIMENSIONS AND PROVIDE SHOP
DRAWINGS.
N
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
3 5/8" 18 Ga. METAL STUDS
FRAMING @ 16" O.C.,
DOUBLE STUD @ CORNERS
SCHLUTER QUADEC (OR
SIM.) CORNER GUARD,
FINISH TO BE SELECTED
19
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
>WT-10:
MANUFACTURER: SUSAN JABLON
STYLE: GLASS MOSAIC
SIZE: MOSAIC
COLOR:
GROUT: MAPEI OPTICOLOR OR SIMILAR.
SCHLUTER QUADEC (OR
SIM.) CORNER GUARD,
FINISH TO BE SELECTED
3 5/8" 18 Ga. METAL STUDS
FRAMING @ 16" O.C.,
DOUBLE STUD @ CORNERS
3 5/8" 18 Ga. METAL STUDS
FRAMING @ 16" O.C.,
DOUBLE STUD @ CORNERS
REFER TO INTERIOR ELEVATIONS FOR TILE PATTERNS.
SCHLUTER QUADEC (OR
SIM.) CORNER GUARD,
FINISH TO BE SELECTED
TOILET ACCESSORIES SCHEDULE
REFER TO SPECIFICATION SECTION 10 2800
1 1/2" = 1'-0"
17
TOILET ROOM - PD 4
TA-6
1 1/2" = 1'-0"
TR-4
T6, T7
TA-6
15
TOILET ROOM - PD 5
1 1/2" = 1'-0"
>TA-1:
TOILET ROOM - PD 6
>TA-3: SANITARY NAPKIN DISPOSAL
BOBRICK B-254
SURFACE-MOUNTED SANITARY NAPKIN DISPOSAL
T9
TA-7, T3
TA-1
TR-4
TA-4
TA-7, T3
TA-1
WT-8
WT-8
WT-8
WT-8
WT-9
WT-9
WT-9
WT-9
WT-9
WT-8
TA-4
WT-8
TA-6
WT-8
TR-1
TR-2
TR-3
3
TA-3
TA-2
T2
T1
T2
T1
109
WT-8
T2
T1
T2
T1
TA-3
TA-2
4
130 SOUTH PARTIAL 2
5
130 NORTH
1/4" = 1'-0"
1/4" = 1'-0"
6
130 WEST
1/4" = 1'-0"
T6, T7
130 SOUTH PARTIAL 1
1/4" = 1'-0"
TR-4
7
TR-1
TR-1
TR-3
TR-3
TA-4
TR-4
T9
TA-6
TA-1
TR-4
WT-8
WT-8
WT-10
WT-10
WT-10
WT-10
WT-10
WT-8
WT-8
WT-8
T2
T2
T2
T1
T1
T1
1/4" = 1'-0"
131 SOUTH PARTIAL 1
1/4" = 1'-0"
10
AGK/JNC
CHECKED BY:
AGK/JNC
>TA-4: HAND DRYER
DXRM5-Q973 AIRMAX HAND DRYER BY WORLD DRYER,
AUTOMATIC, BRUSHED STAINLESS STEEL, RECESSED (ADA), 115
VOLTS
>TA-5: RECESSED TRASH BIN
BOBRICK B-43644 CONTURASERIES
RECESSED WASTE RECEPTACLE WITH LINERMATE
>TA-7:
MIRROR
>TA-8: HOOKS
BOBRICK B-2116
HEAVY-DUTY CLOTHES HOOK WITH CONCEALED MOUNTING
WT-8
T2
T1
TA-2
9
DRAWN BY:
TA-6
TA-2
131 NORTH
REVISIONS
WT-8
TA-6
8
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
TA-6
WT-8
110
ENGINEER:
1/4" = 1'-0"
WT-8
T1
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
130 EAST
WT-8
T2
ARCHITECT:
>TA-6: GRAB BARS
BOBRICK B-5806
1¼" DIAMETER STAINLESS STEEL GRAB BARS WITH SNAP FLANGE
TA-5
WT-8
SOAP DISPENSER
>TA-2: TOILET PAPER DISPENSER
ROYCE ROLLS RINGER COMPANY
4 ROLL 20-1/8” TP-4
1 1/2" = 1'-0"
WT-8
T2
T1
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
>WT-9:
MANUFACTURER: SUSAN JABLON
STYLE: GLASS MOSAIC
SIZE: MOSAIC
COLOR:
GROUT: MAPEI OPTICOLOR OR SIMILAR.
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
EXISTING CMU
WALL TO REMAIN
3 5/8" 18 Ga. METAL STUDS
FRAMING @ 16" O.C.,
DOUBLE STUD @ CORNERS
16
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
>WT-8:
MANUFACTURER: NEMO TILE
STYLE: VOGUE SHADES
SIZE: 20" x 20" CUT 2
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
EXISTING CMU
WALL TO REMAIN
TOILET ROOM - PD 2
I
REFER TO SPECIFICATION SECTION 09 3000 TILING
SCHLUTER QUADEC (OR
SIM.) CORNER GUARD,
FINISH TO BE SELECTED
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
14
R E D A RC H
WALL TILE INFORMATION
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
19
3 5/8" 18 Ga. METAL STUDS
FRAMING @ 16" O.C.,
DOUBLE STUD @ CORNERS
>TR-1:
GRANITE COUNTER TOP
TYPE:
COLOR: TO BE SELECTED
FIELD VERIFY ALL DIMENSIONS AND PROVIDE SHOP
DRAWINGS.
>TR-3:
UNDER COUNTER PLUMBING SHROUD
STYLE: FACE FASTENED PANEL
MATERIAL: SOLID SURFACE
COLOR: TO BE SELECTED
FIELD VERIFY ALL DIMENSIONS AND PROVIDE SHOP
DRAWINGS.
N
DECORATIVE WALL TILE OVER
1/2" CONCRETE BACKER
BOARD, REFER TO I-102 FOR
FINISH INFORMATION
TE
TOILET ROOM FINISH INFORMATION
>TR-2:
SINK BOWL
STYLE: UNDERMOUNT
SIZE:
COLOR: STAINLESS
SCHLUTER QUADEC
(OR SIM.) CORNER
GUARD, FINISH TO BE
SELECTED
1/4" = 1'-0"
EXISTING CMU
WALL TO REMAIN
S
No.
16419
2' - 10 7/8"
TOILET ROOMS - DIMENSIONS
1/4" = 1'-0"
PROVIDE SANITARY COVE BASE.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP TO
12".
PROVIDE MIRROR TO FIT LENGTH OF WALL AND SINK AREA.
ADHERE MIRROR DIRECTLY TO WALL AND TRIM OUT WITH
APPROPRIATE SCHLUTER TRIM.
NEW WALL TILE OVER EXISTING CMU WALL.
GWB CEILING SOFFIT. PAINT I-OP. COLORS TO BE SELECTED.
NEW DOOR AND FRAME. BUTT SCHLUTER STRIP SNUGLY
AGAINST FRAME AND PROVIDE CLEAN GROUT EDGE.
PAINT NEW DOOR AND FRAME I-OP-MD-DT, COLORS TO BE
SELECTED.
REFER TO REFLECTED CEILING PLAN FOR FURTHER
INFORMATION.
PROVIDE SMALL PLAQUE SIGN WHICH READS "EMPLOYEES
MUST WASH HANDS BEFORE RETURNING TO WORK".
3 5/8" 18 Ga. METAL STUDS
FRAMING @ 16" O.C.,
DOUBLE STUD @ CORNERS
ALIGN
1' - 1 5/8"
1
4.
5.
6.
3 5/8" 18 Ga.
METAL STUDS
FRAMING @ 16"
O.C., DOUBLE STUD
@ CORNERS
4' - 0 1/4"
110
109
S-3.1B
0
MEN
131
9
13
I-300
3.
1 1/2" = 1'-0"
17
I-300
S-3B
0
S-3.1B
0
4
11
I-300
TR-1, 2, 3
TA-7
TA-1
TA-2, TA-3
TA-1
TA-7
TR-1, 2, 3
12
TYPICAL TILE CORNER
1.
2.
C N
RK
131 SOUTH PARTIAL 2
1/4" = 1'-0"
TR-1
TR-3
TA-2
11
131 WEST
1/4" = 1'-0"
12
131 EAST
1/4" = 1'-0"
TA-2
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
I-300
PHASE 2: ALTERATIONS & ADDITIONS
S-3B
0
2 1/2" 18 Ga.
METAL STUDS
FRAMING @ 16"
O.C., DOUBLE STUD
@ CORNERS
E
NEW
OF O J
RCNJ No. 2014-37-01C
TA-2, TA-3
T9
2' - 8"
3' - 1"
WOMEN
130
WT-1
0
3' - 1"
10
19
1' - 3"
TA-8
WOMEN
130
2' - 5 1/4"
T9
TR-4, TYP.
TOILET ROOM KEYED NOTES
I
18
I-300
TA-2, TA-3
WT-1
0
WT-1
0
SEALED:
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
TR-4
2' - 7"
WT-1
0
15
I-300
DECORATIVE WALL TILE
OVER 1/2" CONCRETE
BACKER BOARD, REFER
TO I-102 FOR FINISH
INFORMATION
R EG
S-3.1B
0
F.
THE PREFIX "T" INDICATES TOILET ROOM NOTE.
5' - 3"
TA-8
E.
N
TA-8
D.
SEY
ER OR
TA-2, TA-3
TR-1, 2, 3
T9
2' - 8"
C.
G.
7' - 11 5/8"
TA-2
5' - 4 7/8"
5
4"
1' - 5 1/4"
I-300
TA-7
TA-1
10' - 0 3/8"
7
TA-2
TR-4
DECORATIVE WALL TILE
OVER 1/2" CONCRETE
BACKER BOARD. REFER
TO I-102 FOR FINISH
INFORMATION
3' - 1"
S-3.1B
0
TA-8
3' - 1"
S-3.1B
0
DECORATIVE WALL
TILE OVER 1/2"
CONCRETE BACKER
BOARD, REFER TO
I-102 FOR FINISH
INFORMATION
SCHLUTER QUADEC (OR SIM.)
CORNER GUARD, FINISH TO BE
SELECTED
1' - 7"
19
TA-6
S-3.1B
0
EXISTING WALL TO REMAIN
RAMAPO COLLEGE
OF NEW JERSEY
S-3.1B
0
TA-8
TA-2, TA-3
TA-6
3
19
7' - 6 1/2"
S-3.1B
0
ALIGN
3' - 1"
TA-8
TA-6
5' - 1"
1' - 7"
WT-1
0
S-3.1B
0
2' - 0 1/2"
S-3.1B
0
TR-4
S-3.1B
0
4' - 9"
17
I-300
TA-2, TA-3
1' - 0 1/2"
WT-1
0
S-3.1B
0
3 5/8" 18 Ga. METAL STUDS
FRAMING @ 16" O.C.,
DOUBLE STUD @ CORNERS
S-3.1B
0
WT-1
0
16
I-300
B.
20
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL
WALL TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS
SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT
ALL WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP
CAP.
REFER TO ADA SHEET FOR FIXTURE AND TOILET
ACCESSORY HEIGHTS.
CT
3' - 7 1/4"
TE
2' - 9 3/4"
SCOTT STUDENT CENTER
RESIDENTIAL DINING
2' - 6 1/4"
MA
6' - 5 1/4"
S TAT
N
TOILET ROOMS
M
SEE SCHEDULE
4' - 8"
SEE SCHEDULE
THICKNESS
0' - 1 3/4"
0' - 1 3/4"
0' - 1 3/4"
0' - 2 1/4"
MAT
FIN
I-OP-MD-DT
I-OP-MD-DT
I-OP-MD-DT
CA
HM
HM
HM
AL
FRAME TYPE
EXISTING
EXISTING
EXISTING
SF14
MAT
EXISTING
EXISTING
EXISTING
AL
FIN
I-OP-MD-DT
I-OP-MD-DT
I-OP-MD-DT
CA
HEAD DIM
EXISTING
EXISTING
EXISTING
1-3/4"
GLAZING TYPE HARDWARE GROUP NUMBER
GL-1
HW-13
GL-1
HW-2
HW-2
GL-1
HW-1
COMMENTS
VERIFY DIMENSIONS OF EXISTING OPENINGS IN FIELD PRIOR TO ORDERING NEW UNITS
GLAZING KEY
D1
VISION PANEL
DOOR
INTERIOR GLASS
SEALED:
SF1
SF14
FULL GLASS
DOOR
MA
S TAT
E
NEW
OF O J
1/4" = 1'-0"
1/4" = 1'-0"
ADD/ALT 1
12' - 3 1/4"
FRAME TYPE - ELEVATION
ADD/ALT 1
11' - 10"
TE
No.
16419
R E D A RC H
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
BACKSPLASH
3' - 0"
2' - 6"
BACKSPLASH
S
I
ADD/ ALT 1
3
DOOR TYPES - ELEVATION
R EG
2
ALUMINUM
FIELD PAINTED, MEDIUM DUTY, DOOR/TRIM SEMI GLOSS,
COLOR TO BE SELECTED
C N
RK
N
1/4" THICK TEMPERED CLEAR GLAZING
FINISH KEY
10
7
115
I-404
9
I-404
8
I-404
11
ENGINEER:
I-404
I-404
NEW MILLWORK
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
12
I-404
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
I-404
6
PROVIDE NEW
SNEEZE GUARD TO
MATCH EXISTING
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
4
I-402
BACKSPLASH
REVISIONS
3
I-404
5
BACKSPLASH
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
I-404
NEW SOLID SURFACE
COUNTER TOP ON
EXISTING MILLWORK WITH
NEW FRONT SURFACE
2
I-404
1
AGK/JNC
CHECKED BY:
AGK
3
I-402
I-403
NEW SOLID SURFACE
COUNTER TOP ON
EXISTING MILLWORK WITH
NEW FRONT SURFACE
1
I-405
15
I-404
5
I-404
13
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
I-403
14
NEW MILLWORK
NEW SOLID SURFACE
COUNTER TOP ON
EXISTING MILLWORK WITH
NEW FRONT SURFACE
"
-0
"
-4
3'
I-404
2
I-402
4
3'
ADD/ALT 2
1'
I-403
NEW MILLWORK
I-403
NEW MILLWORK
NEW SOLID SURFACE
COUNTER TOP ON
EXISTING MILLWORK WITH
NEW FRONT SURFACE
0"
11
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
7/
8"
I-403
1
3'
NEW MILLWORK
0"
-1
112
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
NEW SOLID SURFACE
COUNTER TOP ON
EXISTING MILLWORK WITH
NEW FRONT SURFACE
113
1
3'
"
-3
3
I-402
7
NEW MILLWORK
I-403
I-403
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
NEW SOLID SURFACE
COUNTER TOP ON EXISTING
MILLWORK WITH NEW FRONT
SURFACE
6'
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
6"
2
I-403
NEW MILLWORK - 3 SIDED MILLWORK
DIE WALL TO MATCH STYLE AND
CONFIGURATION OF EXISTING
MILLWORK
NO BACKSPLASHES AT THIS
LOCATION - TILE TO COUNTER
AND PROVIDE CLEAN SILICONE
LINE BETWEEN COUNTER AND TILE
NEW MILLWORK
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
1
ADD/ALT 1
SERVERY PLAN
1/4" = 1'-0"
I-400
PHASE 2: ALTERATIONS & ADDITIONS
I-403
8
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
REUSE EXISTING
SNEEZE GUARD,
REPAINT FRAME
RCNJ No. 2014-37-01C
6
114
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
PROVIDE NEW
SNEEZE GUARD TO
MATCH EXISTING
I-404
9
DRAWN BY:
RAMAPO COLLEGE
OF NEW JERSEY
4
SCOTT STUDENT CENTER
RESIDENTIAL DINING
I-404
ENLARGED PLAN - SERVERY
AL
I-OP-MD-DT
SOLID DOOR
115
SEY
ER OR
GL-1
D2
1' - 3 3/4"
HEIGHT
7' - 0"
7' - 0"
7' - 0"
7' - 0"
3' - 2 5/8"
1' - 4" 2' - 0" 6" 2' - 0"
WIDTH
3' - 0"
3' - 0"
2' - 8"
3' - 0"
7' - 1 3/4"
DOOR TYPE
D1
D1
D2
SF1
SEE SCHEDULE
LOCATION
RESIDENTIAL SERVERY
RESIDENTIAL SERVERY
RESIDENTIAL SERVERY
RESIDENTIAL SERVERY
7' - 11 7/8"
DOOR #
112
113
114
115
SEE SCHEDULE
SERVERY DOOR SCHEDULE
SEE SCHEDULE
1' - 5 3/8"
CT
SEE SCHEDULE
TE
3/23/2016 7:05:50 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
3/23/2016 6:22:25 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
REPLACE ALL SIGNAGE
CLEAN AND PAINT ALL METAL WORK
REPLACE ALL EXISTING COUNTERS WITH
SOLID SURFACE, REMOVE ALL EXISTING
EQUIPMENT, STORE AND REINSTALL
I
TE
CT
No.
16419
TE
R EG
S
C N
RK
N
MA
E
NEW
OF O J
SEY
ER OR
S TAT
SEALED:
R E D A RC H
I
PROVIDE NEW MILLWORK FACES
PROVIDE NEW PAINTED METAL MILLWORK TRIM ON EXISTING LEGS
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
ADD ALT 1
ADD ALT 1
ADD ALT 1
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ADD ALT 1
ARCHITECT:
REUSE EXISTING TRACK, REPLACE
ALL TRACK LIGHT FIXTURES
REPLACE ALL EXISTING COUNTERS WITH SOLID
SURFACE, REMOVE ALL EXISTING EQUIPMENT,
STORE AND REINSTALL
PROVIDE NEW GRAPHICS ON
EXISTING MILLWORK
NEW TILE ON CONCRETE COLUMN
PROVIDE NEW LAMINATE PANELS
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
REPLACE ALL EXISTING COUNTERS WITH SOLID
SURFACE, REMOVE ALL EXISTING EQUIPMENT, STORE
AND REINSTALL
AGK
CHECKED BY:
AGK
CLEAN AND PAINT ALL METAL WORK
PROVIDE NEW MILLWORK FACES
REPLACE TILE BASE
REMOVE WOOD FOR NEW STAIR SYSTEM
SCOTT STUDENT CENTER
RESIDENTIAL DINING
ADD ALT 1
PROVIDE NEW GRAPHICS
ON EXISTING MILLWORK
REMOVE SHADOW BOXES
REMOVE LAMINATE
PANELS
CLEAN AND
PAINT ALL
METAL WORK
CLEAN AND PAINT
ALL METAL WORK
PROVIDE NEW PAINTED METAL MILLWORK
TRIM ON EXISTING LEGS
ADD ALT 1
ADD ALT 1
ADD ALT 1
RAMAPO COLLEGE
OF NEW JERSEY
PROVIDE NEW
LAMINATE PANELS
REPLACE ALL SIGNAGE
PHOTOS - SERVERY
NEW TILE LOCATION, PROVIDE SCHLUTER
DIVIDER STRIP BETWEEN THE TILE TYPES
NEW TILE ON CONCRETE COLUMN
REMOVE TV AND PLAQUE AND
RETURN TO OWNER
REMOVE WOOD FOR NEW STAIR SYSTEM
CLAD PLANTER WITH NEW STEEL
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
REPLACE TILE BASE
CLAD PLANTER WITH NEW STEEL
I-401
PHASE 2: ALTERATIONS & ADDITIONS
CLAD PLANTER WITH NEW STEEL
RCNJ No. 2014-37-01C
PROVIDE NEW PAINTED METAL
MILLWORK TRIM ON EXISTING LEGS
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
REPLACE ALL EXISTING SNEEZE GUARDS NEW SNEEZE GUARDS
ADD ALT 1
DRAWN BY:
METAL CHANNEL AND BOLT SIZES
E.
8" METAL LETTERING
APPLIED TO WF-3.
LETTERS AND FONT TO
BE SELECTED
13
I-460
F.
G.
10
I-460
EXISTING PIPE & TUBE
FRAMING TO REMAIN,
NEW PAINTED FINISH.
1x MAPLE BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
1 1/4"
GAP
WF-3 IN MAPLE FRAME
REMOVE PLAM PANELS
EXISTING STATION
NEW STATION
NEW 1x MAPLE CORNERS w/
EXISTING STEEL TRIM TO BE
REINSTALLED w/ NEW PAINTED
FINISH. NEW MAPLE CORNERS TO
MATCH EXISTING IN DIMENSION.
1
ADD/ ALT 1
NEW SOLID SURFACE
COUNTERTOPS
MF-1
EXISTING STAINLESS STEEL SUB
FRAME TO REMAIN UNCHANGED
1"
GAP
REMOVE EXISTING
SHADOW BOX &
SUPPORTS. GRIND ALL
EDGES, HOLES, & CUTS
SMOOTH TO TOUCH
MF-1
VERTICAL 1x MAPLE BOARDS ON
3/4" PLASTIC LAMINATED
FINISHED PLYWOOD. 1" VERTICAL
GAP BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
EXISTING SIGN WING
2.
(5) MAPLE BOARDS w/
1" GAP IN BETWEEN
3.
2"
TYP.
(5) MAPLE BOARDS w/
3/4" GAP IN BETWEEN
4.
(5) MAPLE BOARDS w/
1/2" GAP IN BETWEEN
5.
6.
7.
NEW SIGN WING
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
8.
9.
10.
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
MEDITERANEAN STATION
11.
12.
1/4" = 1'-0"
13.
14.
15.
16.
EXISTING PIPE FRAMING
TO REMAIN, NEW
PAINTED FINISH.
17.
8" METAL LETTERING
APPLIED TO WF-3.
LETTERS AND FONT TO
BE SELECTED
18.
WF-3 IN MAPLE FRAME
10
I-460
GRILL
EXISTING CANOPY
TO REMAIN
UNCHANGED.
REMOVE ALL
EXISTING SIGNAGE,
PANELS, & CLIPS
EXISTING CANOPY TO
REMAIN UNCHANGED.
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
EXISTING STEEL ANGLE
& FLAT STOCK TRIM TO
REMAIN, NEW
PAINTED FINISH.
13
I-460
STEEL REMAINS
REMOVE PLAM PANELS
EXISTING PIPE & TUBE
FRAMING TO REMAIN,
NEW PAINTED FINISH.
1x MAPLE BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
W-3, NOTE 23, 24
(6) MAPLE BOARDS w/
1" GAP IN BETWEEN
1x VERTICAL MAPLE
BOARDS, BEYOND.
MOUNTED TO EXISTING
CROSS BRACING.
(5) MAPLE BOARDS w/
1" GAP IN BETWEEN
REMOVE EXISTING
SHADOW BOX &
SUPPORTS. GRIND ALL
EDGES, HOLES, & CUTS
SMOOTH TO TOUCH
(5) MAPLE BOARDS w/
3/4" GAP IN BETWEEN
(5) MAPLE BOARDS w/
1/2" GAP IN BETWEEN
19.
20.
21.
TERMINATE WT-1 BRICK TILE WITH SCHLUTER STRIP AT THE
JOINT WHERE EXISTING TILE STOPS.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP
TO 12".
PROVIDE APPROPRIATE SCHLUTER EXTRUDED METAL TILE
EDGE DETAILS. CLEAR ALUMINUM.
EXISTING BRICK TO REMAIN - NO PAINT OR ADDITIONAL
WALL FINISH.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP CAP.
CONTINUE WT-1 TILE FROM EXISTING WALL INTO WORK
AREA. REMOVE CUT TILES AND REPLACE WITH NEW FULL
TILES AS REQUIRED TO BLEND IN PATTERN.
PROVIDE 2" STEEL ANGLE AS CORNER GUARD WITH 2" STEEL
FLAT STOCK AS BASE AND 2" STEEL FLAT STOCK @ 8'-0"
SECURED WITH BOLTS AND WASHERS TO STUDS.
EXISTING WALL TILE TO REMAIN.
WOOD PLANTER BOX TO REMAIN AND BE RECOVERED
WITH STEEL PLATE. REFER TO DETAILS.
PROVIDE FULL HEIGHT STEEL FLAT STOCK EDGE, REFER TO
DETAIL.
PROVIDE NEW GWB WALLS, PREP AND PAINT. COLOR TO
BE DETERMINED.
EXISTING WALLS, PREP AND PAINT, COLOR TO BE
DETERMINED.
PAINT WALLS ABOVE TO EXISTING CEILING.
PAINT NEW STAIR RAILING I-OP-HD. REFER TO
SPECIFICATION SECTION 09 9000 PAINTING FOR
ADDITIONAL INFORMATION. COLORS TO BE SELECTED.
NEW WALL TILE OVER EXISTING CMU WALL.
PROVIDE STEEL C-CHANNEL DETAILS AT BOOTH ENDS. WITH
IN CHANNEL WELD 2 CUSTOM HOOKS BENT FROM 8"
BOLTS. 1@30" AFF AND 1@60" AFF.
PAINT COLUMNS WITHIN STEEL FRAME AN ACCENT COLOR
TO BE SELECTED. PAINT COLUMNS ABOVE STEEL TO MATCH
CEILING COLOR.
GWB CEILING CLOUD. PAINT I-OP. COLORS TO BE
SELECTED.
EXISTING DOOR AND FRAME TO REMAIN. BUTT SCHLUTER
STRIP SNUGLY AGAINST FRAME AND PROVIDE CLEAN
GROUT EDGE.
PAINT EXISTING DOOR AND FRAME I-OP-MD-DT, COLORS
TO BE SELECTED.
PROVIDE SOLID SURFACE SILL/WALL CAP.
INTERIOR PAINT INFORMATION
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING FOR ADDITIONAL INFORMATION.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
> TYPE I-OP ALL INTERIOR SURFACES INDICATED TO BE PAINTED.
EGGSHELL FINISH.
COLORS TO BE SELECTED.
W.
X.
EXISTING STATION
NEW STATION
NEW 1x MAPLE CORNERS w/
EXISTING STEEL TRIM TO BE
REINSTALLED w/ NEW PAINTED
FINISH. NEW MAPLE CORNERS TO
MATCH EXISTING IN DIMENSION.
2
ADD/ ALT 1
MF-1
EXISTING STAINLESS STEEL SUB
FRAME TO REMAIN UNCHANGED
NEW SOLID SURFACE
COUNTERTOPS
EXISTING SIGN WING
MF-1
VERTICAL 1x MAPLE BOARDS ON
3/4" PLASTIC LAMINATED
FINISHED PLYWOOD. 1" VERTICAL
GAP BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
NEW SIGN WING
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
GRILL
> TYPE I-OP-MD-DT MEDIUM DUTY DOOR/TRIM.
SEMI-GLOSS.
COLORS TO BE SELECTED.
Y.
> TYPE I-OP-HD HEAVY DUTY VERTICAL AND OVERHEAD
EPOXY GLOSS.
COLORS TO BE SELECTED.
Z.
> TYPE I-OP-DF DRY FALL.
FLAT.
COLORS TO BE SELECTED.
1/4" = 1'-0"
> TYPE I-TR -W TRANSPARENT FINISH ON WOOD.
WALL FINISH INFORMATION
8" METAL LETTERING
APPLIED TO WF-3.
LETTERS AND FONT TO
BE SELECTED
WF-3 IN MAPLE FRAME
10
I-460
HOMETOWN
EXISTING CANOPY
TO REMAIN
UNCHANGED.
13
I-460
REMOVE ALL
EXISTING SIGNAGE,
PANELS, & CLIPS
STEEL REMAINS
REMOVE PLAM PANELS
EXISTING STATION
NEW 1x MAPLE CORNERS w/
EXISTING STEEL TRIM TO BE
REINSTALLED w/ NEW PAINTED
FINISH. NEW MAPLE CORNERS TO
MATCH EXISTING IN DIMENSION.
3
ADD/ ALT 1
MF-1
NEW STATION
EXISTING STAINLESS STEEL SUB
FRAME TO REMAIN UNCHANGED
NEW SOLID SURFACE
COUNTERTOPS
MF-1
VERTICAL 1x MAPLE BOARDS ON
3/4" PLASTIC LAMINATED
FINISHED PLYWOOD. 1" VERTICAL
GAP BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
EXISTING SIGN WING
(5) MAPLE BOARDS w/
1" GAP IN BETWEEN
(5) MAPLE BOARDS w/
3/4" GAP IN BETWEEN
REMOVE EXISTING
SHADOW BOX &
SUPPORTS. GRIND ALL
EDGES, HOLES, & CUTS
SMOOTH TO TOUCH
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
1x MAPLE BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
(6) MAPLE BOARDS w/
1" GAP IN BETWEEN
W-3, NOTE 23, 24
1x VERTICAL MAPLE BOARDS,
BEYOND. MOUNTED TO
EXISTING CROSS BRACING.
EXISTING CANOPY TO
REMAIN UNCHANGED.
EXISTING STEEL ANGLE
& FLAT STOCK TRIM TO
REMAIN, NEW
PAINTED FINISH.
EXISTING PIPE & TUBE
FRAMING TO REMAIN,
NEW PAINTED FINISH.
>WF-1: RECLAIMED THIN WOOD
MANUFACTURER: STIKWOOD
STYLE: RECLAIMED
COLOR: MULTIPLE COLORS, TO BE SELECTED
FINISH WITH 3 COATS I-TR-W
PRODUCT MUST BE ORDERED WITH CLASS A FIRE RATED
TREATMENT OR TREATED AS SUCH ON SITE
SPECIFICATION SECTION: 06 4216 WOOD VENEER PANELING
1/4" = 1'-0"
EXISTING PIPE FRAMING
TO REMAIN, NEW
PAINTED FINISH.
>WT-1:
MANUFACTURER: SENECA BRICK
STYLE: THIN BRICK TILE
SIZE: 2 "x 8", BRICK
COLOR: GLACIER BLEND
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-3:
MANUFACTURER: SUSAN JABLON MOSAICS
STYLE: RECYCLED
SIZE: 3/4" x 3/4"
COLOR: WHITE
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
WF-3 IN MAPLE FRAME
EXISTING CANOPY
TO REMAIN
UNCHANGED.
STEEL REMAINS
REMOVE PLAM PANELS
EXISTING STATION
6' - 8"
EXISTING CANOPY TO
REMAIN UNCHANGED.
NEW STEEL AND
GLASS SNEEZE
GUARD TO
MATCH
EXISTING
NEW STATION
NEW 1x MAPLE CORNERS w/
EXISTING STEEL TRIM TO BE
REINSTALLED w/ NEW PAINTED
FINISH. NEW MAPLE CORNERS TO
MATCH EXISTING IN DIMENSION.
EXISTING STEEL ANGLE
& FLAT STOCK TRIM TO
REMAIN, NEW
PAINTED FINISH.
REMOVE EXISTING
SHADOW BOX &
SUPPORTS. GRIND ALL
EDGES, HOLES, & CUTS
SMOOTH TO TOUCH
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
MF-1
EXISTING STAINLESS STEEL SUB
FRAME TO REMAIN UNCHANGED
NEW SOLID SURFACE
COUNTERTOPS
MF-1
VERTICAL 1x MAPLE BOARDS ON
3/4" PLASTIC LAMINATED
FINISHED PLYWOOD. 1" VERTICAL
GAP BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
EXISTING SIGN WING
W-3, NOTE 23, 24
1x VERTICAL MAPLE
BOARDS, BEYOND.
MOUNTED TO
EXISTING CROSS
BRACING.
EXISTING PIPE & TUBE
FRAMING TO REMAIN,
NEW PAINTED FINISH.
1x MAPLE BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
(6) MAPLE BOARDS w/
1" GAP IN BETWEEN
(5) MAPLE BOARDS w/
1" GAP IN BETWEEN
(5) MAPLE BOARDS w/
3/4" GAP IN BETWEEN
(5) MAPLE BOARDS w/
1/2" GAP IN BETWEEN
NEW SIGN WING
>WT-4:
MANUFACTURER: NEMO TILE
STYLE: RAZOR
SIZE: 3/4" x 4"
COLOR: MATTE STAINLESS
GROUT: MAPEI OPTICOLOR OR SIMILAR. COLOR TO BE
SELECTED.
>WT-5:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: LEAD
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-6:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: MOSS
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-7:
MANUFACTURER: FIRECLAY TILE
STYLE: PICKET
SIZE: 10-1/4" x 3-3/4"
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
4
ADD/ ALT 1
PIZZA
1/4" = 1'-0"
12.
15.
>WT-2:
MANUFACTURER: FIRECLAY TILE
STYLE: KITE
SIZE: 7-1/2" x 5-1/2"
COLOR: SEVERAL COLORS TO BE SELECTED
GROUT: 1/8" GROUT JOINTS IN MAPEI OPTICOLOR OR
SIMILAR. COLOR TO BE SELECTED.
REMOVE ALL
EXISTING SIGNAGE,
PANELS, & CLIPS
10.
13.
14.
REFER TO SPECIFICATION SECTION 09 3000 TILING
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
PIZZA
9.
>WF-3: VINYL WALLCOVERING
MANUFACTURER: WOLF GORDON
IMAGE AND SUBSTRATE TO BE SELECTED
WALL TILE INFORMATION
10
I-460
6.
7.
8.
11.
NEW SIGN WING
8" METAL LETTERING
APPLIED TO WF-3.
LETTERS AND FONT TO
BE SELECTED
5.
16.
17.
HOMETOWN
13
I-460
1.
2.
3.
>WF-2: "LIVE EDGE" WOOD
MANUFACTURER: MILLWORK
STYLE: TO MATCH EXISTING TREATMENT IN RETAIL SEATING AREA
COLOR: OAK VENEER OVER FIRE RATED PLYWOOD, CLEAR COAT
FINISH WITH 3 COATS I-TR-W
(5) MAPLE BOARDS w/
1/2" GAP IN BETWEEN
>WT-8, WT-9, WT-10:
REFER TO TOILET ROOM SHEET
REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.
E
NEW
OF O J
S
TE
C N
RK
No.
16419
R E D A RC H
18.
19.
20.
21.
22.
23.
24.
25.
GWB SOFFIT, REFER TO RCP FOR INFORMATION.
LINE OF CEILING, REFER TO RCP FOR INFORMATION.
HEAT LAMP TO BE HUNG CENTERED TO EQUIPMENT
BELOW, VERIFY WITH PLACEMENT OF EQUIPMENT PRIOR
TO INSTALLATION.
EXISTING SNEEZE GUARDS, REPAINT AND REPLACE
HARDWARE AS REQUIRED.
SOLID SURFACE COUNTERTOP WITH MINIMUM 2 LAYERS
OF 3/4" PLYWOOD SUBSTRATE ON ALL COUNTERS. REFER
TO SECTION FOR EDGE THICKNESS.
PROVIDE ADEQUATE BLOCKING AS REQUIRED.
SEAL & WATERPROOF ALL COUNTERTOP PENETRATIONS.
SILICONE @ ALL COUNTER TO VERTICAL SURFACE
JOINTS
PROVIDE COUNTER TOP CORE CUT OUT & GROMMET
COVER FOR ALL REQUIRED COUNTERTOP KITCHEN
EQUIPMENT POWER CORDS (TYPICAL).
PROVIDE HEAT PROOFING AT ALL HOT & COLD
EQUIPMENT WITHIN COUNTER SURFACE. REFER TO
DETAIL.
3/4" PLYWOOD DIEWALL CONSTRUCTION (NO
PARTICLEBOARD OR MDF), TYPICAL UNLESS OTHERWISE
NOTED.
UTILITY CHASE IN MILLWORK WITH REMOVABLE PANEL
FOR ACCESS.
TILE BASE, REFER TO FLOOR FINISH PLAN FOR TILE TYPE.
PROVIDE 1/4" GAP BETWEEN FLOOR FINISH AND
VERTICAL PLYWOOD CONSTRUCTION, FILL WITH
CONTINUOUS SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4" PLYWOOD SHOE
SECURED TO FLOOR (TYPICAL).
PROVIDE 4" HIGH SOLID SURFACE BACKSPLASH.
BLACK PLASTIC LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL UNLESS OTHERWISE
NOTED).
2x SOLID WOOD SHELF. SPECIES & FINISH TO BE SELECTED
BY ARCHITECT.
1/8" THICK STEEL FLAT STOCK TRIM SECURED WITH BOLT
AND WASHER DETAIL. FINISH TO BE SELECTED BY
ARCHITECT.
STEEL ANGLE CORNER GUARD SECURED WITH BOLT AND
WASHER DETAIL. FINISH TO BE SELECTED BY ARCHITECT.
POS, PROVIDED BY OTHERS.
VERTICAL STEEL TUBE SUPPORT. FINISH AS INDICATED.
PROVIDE 1/4" THICK SMOOTH MASONITE BACKER
BOARD FOR VINYL GRAPHIC.
2x2 STEEL FRAME WITH CLIPS TO HOLD BACKER BOARD,
WELDED AND GROUND CORNERS, FINISH AS INDICATED
AND SECURE TO WALL WITH Z CLIPS. PROVIDE BLOCKING
WITHIN WALL WHERE POSSIBLE.
SCRIBE ALL COUNTERS TIGHT TO FIT AND SILICONE GAPS
CLEANLY.
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
DRAWN BY:
AGK
CHECKED BY:
AGK
KEYED NOTES
4.
EXISTING PIPE FRAMING
TO REMAIN, NEW
PAINTED FINISH.
SEALED:
N
EXISTING STEEL ANGLE
& FLAT STOCK TRIM TO
REMAIN, NEW
PAINTED FINISH.
1.
D.
SEY
ER OR
STEEL REMAINS
1x VERTICAL MAPLE
BOARDS, BEYOND.
MOUNTED TO EXISTING
CROSS BRACING.
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
(6) MAPLE BOARDS w/
1" GAP IN BETWEEN
C.
I
EXISTING CANOPY TO
REMAIN UNCHANGED.
W-3, NOTE 23, 24
REFER TO WALL FINISH PLAN.
THE PREFIX "W" INDICATES WALL FINISH NOTE.
B.
R EG
EXISTING CANOPY
TO REMAIN
UNCHANGED.
REMOVE ALL
EXISTING SIGNAGE,
PANELS, & CLIPS
3/4"
GAP
MEDITERRANEAN
WALL FINISH KEYED NOTES
REFER TO SPECIFICATIONS 06 4100 ARCHITECTURAL
MILLWORK AND 05 7000 ORNAMENTAL METAL FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 12 3600 COUNTERTOPS
FOR ADDITIONAL INFORMATION.
ALL MILLWORK AND CABINETS SCOPE SHALL BE
CONSTRUCTED AND INSTALLED PER AWI CUSTOM GRADE
STANDARDS.
NO MDF OR PARTICLE BOARD SUBSTRATES WILL BE
ACCEPTABLE. 3/4" PLYWOOD ONLY.
ALL EXPOSED SURFACES SHALL BE THE FINISH AS NOTED ON
ELEVATIONS
ALL SEMI-EXPOSED SURFACES SHALL BE BLACK PLASTIC
LAMINATE.
INTERIOR FACE OF DIE WALLS TO BE FACED WITH BLACK
FRP.
SEAL ALL EXPOSED PLYWOOD EDGES AND MAINTAIN
MINIMUM 1/4" GAP FROM FLOOR TO PREVENT WICKING OF
WATER.
ALL SNEEZE GUARDS/ FOOD SHIELDS SHOWN SHOULD BE
INCLUDED WITHIN THE MILLWORK CONTRACTORS SCOPE OF
WORK.
ANY SIGNAGE & MENU FRAMES SHOULD BE INCLUDED
WITHIN THE MILLWORK'S SCOPE OF WORK
CONTRACTOR TO COORDINATE WITH EQUIPMENT
PROVIDER FOR INSTALLATION AND TESTING OF ALL
EQUIPMENT.
CONTRACTOR IS REQUIRED TO SET EQUIPMENT IN PLACE.
THIS INCLUDES, BUT IS NOT LIMITED TO, ALL OWNER SUPPLIED
"EXISTING" EQUIPMENT. CONTRACTOR TO VERIFY
EQUIPMENT DATA AS PROVIDED IN ELECTRICAL &
PLUMBING DRAWINGS TO MINIMIZE SLAB CORING
POSSIBLE. CONTRACTOR IS RESPONSIBLE FOR PLUMBING &
ELECTRICAL FEEDS TO EQUIPMENT.
PROVIDE P-LAM FACED VERTICAL APRON TO CONCEAL ALL
DROP IN EQUIPMENT AND SINKS. MOUNT ALL EQUIPMENT
CONTROLS TO CABINET FRAME AT APRON. SEE DETAILS.
COORDINATE LOCATIONS WITH EQUIPMENT.
INSIDE VERTICAL MILLWORK SURFACES ADJACENT TO
COOKING EQUIPMENT SHALL BE FINISHED w/ 20GA . TYPE
304 #4 MILL FINISH STAINLESS STEEL PANELS FASTENED TO
PLYWOOD BACKER. ALL JOINTS REQUIRE BATTEN STRIPS.
CONTRACTOR TO PROVIDE ENGINEERED SHOP DRAWINGS
INCLUDING PLAN LAYOUT DETAILS & SPECIFICATIONS FOR
ALL STRUCTURAL CONNECTIONS TO EXISTING BASE
BUILDING STRUCTURE FOR ARCHITECT'S REVIEW &
APPROVAL. ITEMS SHALL INCLUDE BUT NOT LIMITED TO WALL
BRACKET MOUNTING DETAILS, PICKPOINT CONNECTIONS
FOR SUSPENDED CEILING ELEMENTS, BEAM CLAMP,
UNISTRUT AND THREADED ROD DETAILS FOR EXHAUST
HOODS & OTHER SUSPENDED DESIGN ELEMENTS.
ALL EXPOSED BOLT & NUT CONNECTIONS ARE BOTH
FUNCTIONAL AND DECORATIVE. PAINT ALL FASTENERS TO
MATCH.
CALCULATE LOAD WEIGHT OF SUSPENDED OBJECTS TO
DETERMINE THE REQUIRED QUANTITY OF PICK POINT
LOCATIONS.
PROVIDE STAINLESS STEEL SUPPORT LEGS EVERY 4'-0" OR AS
REQUIRED TO AVOID DEFLECTION AND CRACKING OF
COUNTER SURFACE. SECURELY PIN LEG TO THE FLOOR AND
SEAL WITH SILICONE TO MAINTAIN WATERPROOFING BELOW
TILE. COORDINATE LOCATIONS SO AS NOT TO INTERFERE
WITH EQUIPMENT.
ALL EQUIPMENT MUST BE REVIEWED FOR HEIGHT SO AS NOT
TO INTERFERE WITH COUNTER HEIGHTS. ARCHITECT
RESERVES THE RIGHT TO CHANGE FOOT OR CASTER
SELECTION DURING SUBMITTAL TO KEEP HEIGHTS FORM
INTERFERING WITH COUNTERTOPS.
ALL CABINET DOOR HINGES TO BE CONTINUOUS PIANO
HINGES.
PROVIDE REINFORCEMENT TO COUNTERTOP EDGE OVER
LONG SPANS WHERE CUT OUTS FOR EQUIPMENT EXIST.
ALL STRUCTURAL HANGING ELEMENTS SHOULD BE RATED
FOR STRENGTH AND REVIEW IN SHOP DRAWINGS BY
STRUCTURAL ENGINEER.
ALL CUT OUTS FOR COUNTER TOP WELLS MUST HAVE
ROUNDED CORNERS PER MANUFACTURER'S INSTRUCTION.
CONTRACTOR TO VERIFY EQUIPMENT DATA AS PROVIDED
IN ELECTRICAL & PLUMBING DRAWINGS TO MINIMIZE SLAB
CORING, IF POSSIBLE.
PROVIDE HEAVY-DUTY REINFORCED CABINETS/ MILLWORK
STRUCTURE LOCATED UNDER BEVERAGE DISPENSER TYP.
THROUGH OUT PROJECT, PROVIDE P-LAM FACED VERTICAL
APRONS TO CONCEAL ALL DROP IN EQUIPMENT, SEE
DETAILS.
MOUNT ALL EQUIPMENT CONTROLS TO CABINET FRAME AT
APRON, SEE DETAILS.
MILLWORK FINISH INFORMATION
>MF-1: VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
COLOR: 3 COATS OF I-TR-W - COLOR TO BE SELECTED
>MF-2: PLASTIC LAMINATE
COLORS: TO BE SELECTED
>MF-3: SOLID SURFACE COUNTER TOP COLOR 1
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-4: SOLID SURFACE COUNTER TOP COLOR 2
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-5: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: PAINTED WITH CLEAR COAT SEALANT
>MF-6: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: BLACK
>MF-7: ORNAMENTAL METAL
EXPANDED METAL MESH
MANUFACTURER: BY MILLWORK SHOP
COLOR: TO BE SELECTED
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
GLAZING KEY
>GL-1:
STYLE: 1/4" FULLY TEMPERED GLASS
COLOR: CLEAR
>GL-2:
STYLE: CORRUGATED PLEXI GLASS
COLOR: OPAQUE
SHEET:
I-402
PHASE 2: ALTERATIONS & ADDITIONS
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
A.
RCNJ No. 2014-37-01C
C.
D.
EXISTING PIPE FRAMING
TO REMAIN, NEW
PAINTED FINISH.
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL WALL
TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT ALL
WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
PAINT ALL EXPOSED CONDUIT ON WALLS. COLOR TO BE
SELECTED.
FOR SIGNAGE INFORMATION REFER TO SHEET I-460.
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
SECTION
B.
GENERAL NOTES
RAMAPO COLLEGE
OF NEW JERSEY
SECTION
A.
GENERAL NOTES
CT
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
BEYOND.
1x HORIZONTAL MAPLE BOARDS.
(3) SIZES: 1x2, 1x4, 1x6. REFER TO
ELEVATION. MOUNTED TO
EXISTING TUBE w/ PAINTED
THROUGH BOLT & WASHERS.
INTERIOR|ELEVATIONS
TE
1x VERTICAL MAPLE BOARDS.
MOUNTED TO EXISTING CROSS
BRACING w/ PAINTED
THROUGH BOLT & WASHERS.
VERIFY WIDTH & HEIGHT OF
EXISTING BRACING.
WALL FINISHES
SCOTT STUDENT CENTER
RESIDENTIAL DINING
1"
TYP.
3/8" - 16 HEX BOLT
5/16" - WASHER
EXISTING PIPE & TUBE
FRAMING TO REMAIN,
NEW PAINTED FINISH.
MA
}
1/2" - 13 HEX BOLT
7/16" - WASHER
5/16" - 18 HEX BOLT
1/4" - WASHER
EXISTING STAINLESS STEEL SUB
FRAME TO REMAIN UNCHANGED
S TAT
6"+ BAR STOCK
5" & 6" CHANNEL
2" BAR STOCK
2" x 2" ANGLE
VERTICAL 1x MAPLE BOARDS ON
3/4" PLASTIC LAMINATED
FINISHED PLYWOOD. 1" VERTICAL
GAP BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
ELEVATIONS - SERVERY
1/4" - 20 HEX BOLT
3/16" - WASHER
4" BAR STOCK
5" BAR STOCK
}
}
}
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
1/2"
GAP
3/23/2016 6:22:28 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
NEW MILLWORK
F.
NEW SOLID SURFACE
COUNTERTOPS
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
DEMO ENTIRE MILLWORK PIECE
NEW SOLID SURFACE COUNTERTOPS
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
MF-1
ADD/ ALT 1
NEW STATION
DISH RISERS
REMAIN
NEW 1x MAPLE CORNERS w/ EXISTING STEEL
TRIM TO BE REINSTALLED w/ NEW PAINTED
FINISH. NEW MAPLE CORNERS TO MATCH
EXISTING IN DIMENSION.
2
ADD/ ALT 1
1/4" = 1'-0"
3.
RE SURFACE EXISTING
DISH RISERS WITH MAPLE
BOARDS, FACE BOLTED
TO LAMINATE STRUCTURE.
1/4" GAP BETWEEN
BOARDS
NEW SOLID
SURFACE
COUNTERTOPS
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
SALAD
MF-1
NEW WALL BASE
7.
1/4" = 1'-0"
8.
9.
10.
11.
12.
EXISTING CANOPY TO
REMAIN UNCHANGED.
NEW 1x MAPLE CORNERS w/ EXISTING STEEL
TRIM TO BE REINSTALLED w/ NEW PAINTED
FINISH. NEW MAPLE CORNERS TO MATCH
EXISTING IN DIMENSION.
EXISTING CANOPY TO
REMAIN UNCHANGED
8" METAL LETTERING APPLIED TO
WF-3. LETTERS AND FONT TO BE
SELECTED
13
I-460
WF-3 IN MAPLE FRAME
NEW SOLID
SURFACE
COUNTERTOPS
18.
STEEL REMAINS
NEW SOLID SURFACE
COUNTERTOPS
NEW MILLWORK
NEW MILLWORK
SOLID SURFACE
SOLID SURFACE
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
NEW STATION
DISH RISERS
REMAIN
NEW MILLWORK
SURROUND SIZED
TO FIT NEW ICE
CREAM COOLER
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
3
ADD/ALT 1
2' - 8"
EXISTING STATION
RE SURFACE EXISTING DISH
RISERS WITH MAPLE
BOARDS, FACE BOLTED TO
LAMINATE STRUCTURE. 1/4"
GAP BETWEEN BOARDS
ADD/ ALT 1
1/4" = 1'-0"
W20
5
I-460
W8
NOTE 23, 24
EXISTING HOOD
NEW WALL BASE
NOTE 23, 24
> TYPE I-TR -W TRANSPARENT FINISH ON WOOD.
REUSE EXISTING SNEEZE
GUARDS, REPAINT
WF-3
WF-3
WALL FINISH INFORMATION
>WF-1: RECLAIMED THIN WOOD
MANUFACTURER: STIKWOOD
STYLE: RECLAIMED
COLOR: MULTIPLE COLORS, TO BE SELECTED
FINISH WITH 3 COATS I-TR-W
PRODUCT MUST BE ORDERED WITH CLASS A FIRE RATED
TREATMENT OR TREATED AS SUCH ON SITE
SPECIFICATION SECTION: 06 4216 WOOD VENEER PANELING
WT-3
NEW WALL BASE
ADD/ALT 1
6
ADD/ALT 1
1/4" = 1'-0"
METAL TRIM TO
REMAIN AND BE REPAINTED, TYP.
WOK 2
N.
O.
P.
Q.
R.
S.
T.
U.
W.
Y.
Z.
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
>WF-2: "LIVE EDGE" WOOD
MANUFACTURER: MILLWORK
STYLE: TO MATCH EXISTING TREATMENT IN RETAIL SEATING AREA
COLOR: OAK VENEER OVER FIRE RATED PLYWOOD, CLEAR COAT
FINISH WITH 3 COATS I-TR-W
1.
2.
3.
5.
6.
7.
8.
9.
11.
12.
>WF-3: VINYL WALLCOVERING
MANUFACTURER: WOLF GORDON
IMAGE AND SUBSTRATE TO BE SELECTED
1/4" = 1'-0"
13.
14.
15.
16.
17.
EXISTING HOOD TO REMAIN
REMOVE EXISTING OVERHEAD
CONSTRUCTION AND ASSOCIATED
LIGHTING
WALL TILE INFORMATION
REFER TO RCP FOR NEW
HOOD SURROUND
18.
REFER TO SPECIFICATION SECTION 09 3000 TILING
NEW SOLID SURFACE
COUNTERTOPS
NEW SQUARE EXTRUSION
FRAME, PAINTED
REFINISH P-LAM ON FINS
WITH SELF ADHESIVE
LAMINATE, TYP. COLOR TO
BE SELECTED
BOLT AND WASHER
DETAIL
7' - 10"
REMOVE METAL MILLWORK
SURROUNDING HOOD
>WT-1:
MANUFACTURER: SENECA BRICK
STYLE: THIN BRICK TILE
SIZE: 2 "x 8", BRICK
COLOR: GLACIER BLEND
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
1x MAPLE BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
SPACED IRREGULARLY
ALONG STEEL FRAME
6"
REFER TO FLOOR PLAN FOR CUT BACK
DIMENSIONS OF WOK MILLWORK
>WT-2:
MANUFACTURER: FIRECLAY TILE
STYLE: KITE
SIZE: 7-1/2" x 5-1/2"
COLOR: SEVERAL COLORS TO BE SELECTED
GROUT: 1/8" GROUT JOINTS IN MAPEI OPTICOLOR OR
SIMILAR. COLOR TO BE SELECTED.
5' - 0"
>WT-3:
MANUFACTURER: SUSAN JABLON MOSAICS
STYLE: RECYCLED
SIZE: 3/4" x 3/4"
COLOR: WHITE
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
WT-3
MF-1 BETWEEN FINS, TYP.
EXISTING TILE TO BE REMOVED
SALVAGE METAL WORK TO BE
PAINTED AND REINSTALLED
8
ADD/ ALT 1
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
NEW WALL BASE
METAL TRIM TO REMAIN
AND BE RE-PAINTED, TYP.
WOK 1
7
ADD/ALT 1
1/4" = 1'-0"
MEDITERANEAN, SCREEN WALL
>WT-4:
MANUFACTURER: NEMO TILE
STYLE: RAZOR
SIZE: 3/4" x 4"
COLOR: MATTE STAINLESS
GROUT: MAPEI OPTICOLOR OR SIMILAR. COLOR TO BE
SELECTED.
1/4" = 1'-0"
EXISTING P-LAM FINS TO
REMAIN, TYP.
REMOVE EXISTING
COUNTER TOP AND
BACKSPLASH
REMOVE
EXISTING P-LAM
PANELS, TYP.
RE-LAMINATE SIDES WITH
SELF ADHESIVE P-LAM
MF-3
>WT-5:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: LEAD
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
EXISTING P-LAM FINS TO
REMAIN, INSTALL STEEL
FLAT STOCK ON FACE,
SECURE WITH ACORN
SCREWS, TYP
6
I-405
NEW CABINET DOORS
MF-1 ON DOORS
RE-LAMINATE SIDES WITH
SELF ADHESIVE P-LAM
METAL CHANNEL AND BOLT SIZES
1/4" - 20 HEX BOLT
3/16" - WASHER
4" BAR STOCK
5" BAR STOCK
}
}
}
6"+ BAR STOCK
5" & 6" CHANNEL
}
1/2" - 13 HEX BOLT
7/16" - WASHER
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
2" BAR STOCK
2" x 2" ANGLE
EXISTING STATION
9
ADD/ ALT 1
BEVERAGE STATION
1/4" = 1'-0"
REMOVE WALL BASE
NEW STATION
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
NEW WALL BASE
5/16" - 18 HEX BOLT
1/4" - WASHER
3/8" - 16 HEX BOLT
5/16" - WASHER
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
>WT-6:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: MOSS
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-7:
MANUFACTURER: FIRECLAY TILE
STYLE: PICKET
SIZE: 10-1/4" x 3-3/4"
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
>WT-8, WT-9, WT-10:
REFER TO TOILET ROOM SHEET
REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.
E
NEW
OF O J
S
TE
C N
RK
No.
16419
R E D A RC H
19.
20.
21.
22.
23.
24.
25.
GWB SOFFIT, REFER TO RCP FOR INFORMATION.
LINE OF CEILING, REFER TO RCP FOR INFORMATION.
HEAT LAMP TO BE HUNG CENTERED TO EQUIPMENT
BELOW, VERIFY WITH PLACEMENT OF EQUIPMENT PRIOR
TO INSTALLATION.
EXISTING SNEEZE GUARDS, REPAINT AND REPLACE
HARDWARE AS REQUIRED.
SOLID SURFACE COUNTERTOP WITH MINIMUM 2 LAYERS
OF 3/4" PLYWOOD SUBSTRATE ON ALL COUNTERS. REFER
TO SECTION FOR EDGE THICKNESS.
PROVIDE ADEQUATE BLOCKING AS REQUIRED.
SEAL & WATERPROOF ALL COUNTERTOP PENETRATIONS.
SILICONE @ ALL COUNTER TO VERTICAL SURFACE
JOINTS
PROVIDE COUNTER TOP CORE CUT OUT & GROMMET
COVER FOR ALL REQUIRED COUNTERTOP KITCHEN
EQUIPMENT POWER CORDS (TYPICAL).
PROVIDE HEAT PROOFING AT ALL HOT & COLD
EQUIPMENT WITHIN COUNTER SURFACE. REFER TO
DETAIL.
3/4" PLYWOOD DIEWALL CONSTRUCTION (NO
PARTICLEBOARD OR MDF), TYPICAL UNLESS OTHERWISE
NOTED.
UTILITY CHASE IN MILLWORK WITH REMOVABLE PANEL
FOR ACCESS.
TILE BASE, REFER TO FLOOR FINISH PLAN FOR TILE TYPE.
PROVIDE 1/4" GAP BETWEEN FLOOR FINISH AND
VERTICAL PLYWOOD CONSTRUCTION, FILL WITH
CONTINUOUS SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4" PLYWOOD SHOE
SECURED TO FLOOR (TYPICAL).
PROVIDE 4" HIGH SOLID SURFACE BACKSPLASH.
BLACK PLASTIC LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL UNLESS OTHERWISE
NOTED).
2x SOLID WOOD SHELF. SPECIES & FINISH TO BE SELECTED
BY ARCHITECT.
1/8" THICK STEEL FLAT STOCK TRIM SECURED WITH BOLT
AND WASHER DETAIL. FINISH TO BE SELECTED BY
ARCHITECT.
STEEL ANGLE CORNER GUARD SECURED WITH BOLT AND
WASHER DETAIL. FINISH TO BE SELECTED BY ARCHITECT.
POS, PROVIDED BY OTHERS.
VERTICAL STEEL TUBE SUPPORT. FINISH AS INDICATED.
PROVIDE 1/4" THICK SMOOTH MASONITE BACKER
BOARD FOR VINYL GRAPHIC.
2x2 STEEL FRAME WITH CLIPS TO HOLD BACKER BOARD,
WELDED AND GROUND CORNERS, FINISH AS INDICATED
AND SECURE TO WALL WITH Z CLIPS. PROVIDE BLOCKING
WITHIN WALL WHERE POSSIBLE.
SCRIBE ALL COUNTERS TIGHT TO FIT AND SILICONE GAPS
CLEANLY.
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
DRAWN BY:
AGK
CHECKED BY:
AGK
KEYED NOTES
10.
MF-1 BETWEEN FINS, TYP.
BACK LINE
M.
4.
NEW SOLID SURFACE
COUNTERS
REFER TO EQUIPMENT PLAN FOR INFORMATION ON NEW KITCHEN EQUIPMENT
L.
V.
> TYPE I-OP ALL INTERIOR SURFACES INDICATED TO BE PAINTED.
EGGSHELL FINISH.
COLORS TO BE SELECTED.
> TYPE I-OP-DF DRY FALL.
FLAT.
COLORS TO BE SELECTED.
8" METAL LETTERING APPLIED TO
WF-3. LETTERS AND FONT TO BE
SELECTED
NEW PENDANT
LIGHTING
W8
5
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING FOR ADDITIONAL INFORMATION.
> TYPE I-OP-HD HEAVY DUTY VERTICAL AND OVERHEAD
EPOXY GLOSS.
COLORS TO BE SELECTED.
NEW OVERHEAD
CONSTRUCTION, REFER TO RCP
WOK
K.
X.
NOTE 1
13
I-460
INTERIOR PAINT INFORMATION
> TYPE I-OP-MD-DT MEDIUM DUTY DOOR/TRIM.
SEMI-GLOSS.
COLORS TO BE SELECTED.
WF-3 IN MAPLE FRAME
7
6
I-460
WF-3
2x MAPLE TRIM, MATCH
EXISTING DIMENSIONS.
1/4" = 1'-0"
I-405
WF-3
MATCH NEW
MILLWORK DETAILS TO
EXISTING CONDITIONS
VERTICAL 1x MAPLE BOARDS ON 3/4"
PLASTIC LAMINATED FINISHED
PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
DESSERT
21.
J.
MF-1
MATCH NEW
MILLWORK DETAILS
TO EXISTING
CONDITIONS
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
4
SOUP
MF-1
NEW STATION
REMOVE PLAM PANELS
NEW 1x MAPLE CORNERS w/ EXISTING STEEL
TRIM TO BE REINSTALLED w/ NEW PAINTED
FINISH. NEW MAPLE CORNERS TO MATCH
EXISTING IN DIMENSION.
SURFACE TO BE MAPLE BOARDS, FACE
BOLTED TO LAMINATE STRUCTURE. 1/4"
GAP BETWEEN BOARDS
19.
20.
MF-1
VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP
BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
15.
16.
17.
MF-1
REMOVE PLAM PANELS
13.
14.
NEW SOLID SURFACE
COUNTERTOPS
EXISTING STEEL ANGLE & FLAT STOCK
TRIM TO REMAIN, NEW PAINTED
FINISH.
MF-1
EXISTING STATION
8" METAL LETTERING
APPLIED TO WF-3. LETTERS
AND FONT TO BE SELECTED
DESSERT
13
I-460
STEEL REMAINS
WF-3 IN MAPLE FRAME
CONNECT SIGN WITH WIRE
TO STRUCTURE ABOVE
SANDWICHES
STEEL REMAINS
5.
6.
SANDWICH
EXISTING PIPE FRAMING
TO REMAIN, NEW
PAINTED FINISH.
COLUMN COVER TO REMAIN
4.
I.
SEALED:
I
NEW WALL BASE
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
1
EXISTING STATION
VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP
BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
TERMINATE WT-1 BRICK TILE WITH SCHLUTER STRIP AT THE
JOINT WHERE EXISTING TILE STOPS.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP
TO 12".
PROVIDE APPROPRIATE SCHLUTER EXTRUDED METAL TILE
EDGE DETAILS. CLEAR ALUMINUM.
EXISTING BRICK TO REMAIN - NO PAINT OR ADDITIONAL
WALL FINISH.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP CAP.
CONTINUE WT-1 TILE FROM EXISTING WALL INTO WORK
AREA. REMOVE CUT TILES AND REPLACE WITH NEW FULL
TILES AS REQUIRED TO BLEND IN PATTERN.
PROVIDE 2" STEEL ANGLE AS CORNER GUARD WITH 2" STEEL
FLAT STOCK AS BASE AND 2" STEEL FLAT STOCK @ 8'-0"
SECURED WITH BOLTS AND WASHERS TO STUDS.
EXISTING WALL TILE TO REMAIN.
WOOD PLANTER BOX TO REMAIN AND BE RECOVERED
WITH STEEL PLATE. REFER TO DETAILS.
PROVIDE FULL HEIGHT STEEL FLAT STOCK EDGE, REFER TO
DETAIL.
PROVIDE NEW GWB WALLS, PREP AND PAINT. COLOR TO
BE DETERMINED.
EXISTING WALLS, PREP AND PAINT, COLOR TO BE
DETERMINED.
PAINT WALLS ABOVE TO EXISTING CEILING.
PAINT NEW STAIR RAILING I-OP-HD. REFER TO
SPECIFICATION SECTION 09 9000 PAINTING FOR
ADDITIONAL INFORMATION. COLORS TO BE SELECTED.
NEW WALL TILE OVER EXISTING CMU WALL.
PROVIDE STEEL C-CHANNEL DETAILS AT BOOTH ENDS. WITH
IN CHANNEL WELD 2 CUSTOM HOOKS BENT FROM 8"
BOLTS. 1@30" AFF AND 1@60" AFF.
PAINT COLUMNS WITHIN STEEL FRAME AN ACCENT COLOR
TO BE SELECTED. PAINT COLUMNS ABOVE STEEL TO MATCH
CEILING COLOR.
GWB CEILING CLOUD. PAINT I-OP. COLORS TO BE
SELECTED.
EXISTING DOOR AND FRAME TO REMAIN. BUTT SCHLUTER
STRIP SNUGLY AGAINST FRAME AND PROVIDE CLEAN
GROUT EDGE.
PAINT EXISTING DOOR AND FRAME I-OP-MD-DT, COLORS
TO BE SELECTED.
PROVIDE SOLID SURFACE SILL/WALL CAP.
H.
N
2.
NEW STATION
DISH RISERS
REMAIN
REFER TO WALL FINISH PLAN.
THE PREFIX "W" INDICATES WALL FINISH NOTE.
G.
R EG
REMOVE PLAM PANELS
WALL FINISH KEYED NOTES
1.
MF-1
EXISTING STATION
E.
MILLWORK FINISH INFORMATION
>MF-1: VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
COLOR: 3 COATS OF I-TR-W - COLOR TO BE SELECTED
>MF-2: PLASTIC LAMINATE
COLORS: TO BE SELECTED
>MF-3: SOLID SURFACE COUNTER TOP COLOR 1
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-4: SOLID SURFACE COUNTER TOP COLOR 2
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-5: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: PAINTED WITH CLEAR COAT SEALANT
>MF-6: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: BLACK
>MF-7: ORNAMENTAL METAL
EXPANDED METAL MESH
MANUFACTURER: BY MILLWORK SHOP
COLOR: TO BE SELECTED
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
GLAZING KEY
>GL-1:
STYLE: 1/4" FULLY TEMPERED GLASS
COLOR: CLEAR
>GL-2:
STYLE: CORRUGATED PLEXI GLASS
COLOR: OPAQUE
SHEET:
I-403
PHASE 2: ALTERATIONS & ADDITIONS
EXISTING STEEL ANGLE & FLAT STOCK
TRIM TO REMAIN, NEW PAINTED
FINISH.
G.
RCNJ No. 2014-37-01C
SIZE TO FIT NEW EQUIPMENT
D.
SEY
ER OR
RE SURFACE
EXISTING DISH RISERS
WITH MAPLE
BOARDS, FACE
BOLTED TO
LAMINATE
STRUCTURE. 1/4"
GAP BETWEEN
BOARDS
STEEL REMAINS
SALAD
13
I-460
F.
3' - 6"
STEEL REMAINS
NEW MILLWORK
WF-3 IN MAPLE FRAME
C.
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
NEW SOLID
SURFACE
COUNTERTOPS
E.
B.
REFER TO SPECIFICATIONS 06 4100 ARCHITECTURAL
MILLWORK AND 05 7000 ORNAMENTAL METAL FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 12 3600 COUNTERTOPS
FOR ADDITIONAL INFORMATION.
ALL MILLWORK AND CABINETS SCOPE SHALL BE
CONSTRUCTED AND INSTALLED PER AWI CUSTOM GRADE
STANDARDS.
NO MDF OR PARTICLE BOARD SUBSTRATES WILL BE
ACCEPTABLE. 3/4" PLYWOOD ONLY.
ALL EXPOSED SURFACES SHALL BE THE FINISH AS NOTED ON
ELEVATIONS
ALL SEMI-EXPOSED SURFACES SHALL BE BLACK PLASTIC
LAMINATE.
INTERIOR FACE OF DIE WALLS TO BE FACED WITH BLACK
FRP.
SEAL ALL EXPOSED PLYWOOD EDGES AND MAINTAIN
MINIMUM 1/4" GAP FROM FLOOR TO PREVENT WICKING OF
WATER.
ALL SNEEZE GUARDS/ FOOD SHIELDS SHOWN SHOULD BE
INCLUDED WITHIN THE MILLWORK CONTRACTORS SCOPE OF
WORK.
ANY SIGNAGE & MENU FRAMES SHOULD BE INCLUDED
WITHIN THE MILLWORK'S SCOPE OF WORK
CONTRACTOR TO COORDINATE WITH EQUIPMENT
PROVIDER FOR INSTALLATION AND TESTING OF ALL
EQUIPMENT.
CONTRACTOR IS REQUIRED TO SET EQUIPMENT IN PLACE.
THIS INCLUDES, BUT IS NOT LIMITED TO, ALL OWNER SUPPLIED
"EXISTING" EQUIPMENT. CONTRACTOR TO VERIFY
EQUIPMENT DATA AS PROVIDED IN ELECTRICAL &
PLUMBING DRAWINGS TO MINIMIZE SLAB CORING
POSSIBLE. CONTRACTOR IS RESPONSIBLE FOR PLUMBING &
ELECTRICAL FEEDS TO EQUIPMENT.
PROVIDE P-LAM FACED VERTICAL APRON TO CONCEAL ALL
DROP IN EQUIPMENT AND SINKS. MOUNT ALL EQUIPMENT
CONTROLS TO CABINET FRAME AT APRON. SEE DETAILS.
COORDINATE LOCATIONS WITH EQUIPMENT.
INSIDE VERTICAL MILLWORK SURFACES ADJACENT TO
COOKING EQUIPMENT SHALL BE FINISHED w/ 20GA . TYPE
304 #4 MILL FINISH STAINLESS STEEL PANELS FASTENED TO
PLYWOOD BACKER. ALL JOINTS REQUIRE BATTEN STRIPS.
CONTRACTOR TO PROVIDE ENGINEERED SHOP DRAWINGS
INCLUDING PLAN LAYOUT DETAILS & SPECIFICATIONS FOR
ALL STRUCTURAL CONNECTIONS TO EXISTING BASE
BUILDING STRUCTURE FOR ARCHITECT'S REVIEW &
APPROVAL. ITEMS SHALL INCLUDE BUT NOT LIMITED TO WALL
BRACKET MOUNTING DETAILS, PICKPOINT CONNECTIONS
FOR SUSPENDED CEILING ELEMENTS, BEAM CLAMP,
UNISTRUT AND THREADED ROD DETAILS FOR EXHAUST
HOODS & OTHER SUSPENDED DESIGN ELEMENTS.
ALL EXPOSED BOLT & NUT CONNECTIONS ARE BOTH
FUNCTIONAL AND DECORATIVE. PAINT ALL FASTENERS TO
MATCH.
CALCULATE LOAD WEIGHT OF SUSPENDED OBJECTS TO
DETERMINE THE REQUIRED QUANTITY OF PICK POINT
LOCATIONS.
PROVIDE STAINLESS STEEL SUPPORT LEGS EVERY 4'-0" OR AS
REQUIRED TO AVOID DEFLECTION AND CRACKING OF
COUNTER SURFACE. SECURELY PIN LEG TO THE FLOOR AND
SEAL WITH SILICONE TO MAINTAIN WATERPROOFING BELOW
TILE. COORDINATE LOCATIONS SO AS NOT TO INTERFERE
WITH EQUIPMENT.
ALL EQUIPMENT MUST BE REVIEWED FOR HEIGHT SO AS NOT
TO INTERFERE WITH COUNTER HEIGHTS. ARCHITECT
RESERVES THE RIGHT TO CHANGE FOOT OR CASTER
SELECTION DURING SUBMITTAL TO KEEP HEIGHTS FORM
INTERFERING WITH COUNTERTOPS.
ALL CABINET DOOR HINGES TO BE CONTINUOUS PIANO
HINGES.
PROVIDE REINFORCEMENT TO COUNTERTOP EDGE OVER
LONG SPANS WHERE CUT OUTS FOR EQUIPMENT EXIST.
ALL STRUCTURAL HANGING ELEMENTS SHOULD BE RATED
FOR STRENGTH AND REVIEW IN SHOP DRAWINGS BY
STRUCTURAL ENGINEER.
ALL CUT OUTS FOR COUNTER TOP WELLS MUST HAVE
ROUNDED CORNERS PER MANUFACTURER'S INSTRUCTION.
CONTRACTOR TO VERIFY EQUIPMENT DATA AS PROVIDED
IN ELECTRICAL & PLUMBING DRAWINGS TO MINIMIZE SLAB
CORING, IF POSSIBLE.
PROVIDE HEAVY-DUTY REINFORCED CABINETS/ MILLWORK
STRUCTURE LOCATED UNDER BEVERAGE DISPENSER TYP.
THROUGH OUT PROJECT, PROVIDE P-LAM FACED VERTICAL
APRONS TO CONCEAL ALL DROP IN EQUIPMENT, SEE
DETAILS.
MOUNT ALL EQUIPMENT CONTROLS TO CABINET FRAME AT
APRON, SEE DETAILS.
RAMAPO COLLEGE
OF NEW JERSEY
8" METAL LETTERING APPLIED TO
WF-3. LETTERS AND FONT TO BE
SELECTED
A.
CT
C.
D.
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL WALL
TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT ALL
WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
PAINT ALL EXPOSED CONDUIT ON WALLS. COLOR TO BE
SELECTED.
FOR SIGNAGE INFORMATION REFER TO SHEET I-460.
TE
B.
GENERAL NOTES
SCOTT STUDENT CENTER
RESIDENTIAL DINING
EXISTING CANOPY TO
REMAIN UNCHANGED.
EXISTING CANOPY TO
REMAIN UNCHANGED
GENERAL NOTES
MA
A.
COLUMN COVER TO REMAIN
INTERIOR|ELEVATIONS
S TAT
EXISTING PIPE FRAMING
TO REMAIN, NEW
PAINTED FINISH.
WALL FINISHES
ELEVATIONS - SERVERY
3/23/2016 6:22:32 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
3/23/2016 6:22:41 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
NOTE 23, 24
WALL FINISHES
INTERIOR|ELEVATIONS
GENERAL NOTES
GENERAL NOTES
W8
G.
NOTE 13
WALL FINISH KEYED NOTES
WF-3
WOK MILLWORK
NOTE 13
114
REFER TO WALL FINISH PLAN.
THE PREFIX "W" INDICATES WALL FINISH NOTE.
W20
1.
ADD/ALT 1
ADD/ALT 1
ADD/ALT 1
1/4" = 1'-0"
4
WOK 5
ADD/ALT 1
1/4" = 1'-0"
WOK 6
2.
1/4" = 1'-0"
3.
1' - 0"
7
I-460
5.
6.
NOTE 1
NOTE 1
NOTE 1
1' - 0"
NOTE 1
NOTE 1
WT-1
WT-1
NOTE 16
NOTE 23, 24
NOTE 25
REUSE EXISTING SNEEZE
GUARDS, REPAINT
MF-3,
NOTE 5
NOTE 19
PLAM FINS WITH
METAL EDGE
BETWEEN DOORS
SIMILAR TO
BEVERAGE LINE
EXISTING MILLWORK,
TYP FOR 7
NOTE 13
NOTE 16
2' - 10"
NOTE 19
NOTE 13
NOTE 8, 25
NOTE 10
MF-1, NOTE 11
W11
2' - 2"
7' - 1 3/4"
1' - 9 3/4"
2' - 2" 1' - 0"
INTERIOR STOREFRONT
GLASS SYSTEM, GL-1 GLASS
NOTE 25
NOTE 13
22 1/2"
23"
23"
23"
23"
22 1/2"
NOTE 17
7' - 7 3/4"
NOTE 19
6"
WF-3
7' - 1 3/4"
WF-3
NOTE 19
1' - 3 3/4"
1' - 4" 2' - 0" 6" 2' - 0"
PROVIDE STEEL "BEAM" OUT OF 6"
TUBE STEEL TO CONNECT WALLS
6"
2' - 0"
PROVIDE STEEL "BEAM" OUT
OF 6" TUBE STEEL TO
CONNECT WALLS. CONNECT
BEAM WITH STEEL ANGLE AND
BOLT WASHER DETAIL
INTERIOR STOREFRONT
GLASS SYSTEM, GL-1 GLASS
10.
NOTE 8, 25
NOTE 16
11.
13.
14.
NOTE 25
15.
16.
BREAKFAST MILLWORK
NOTE 14, 15
17.
NOTE 14, 15
8
I-405
5
6
WOK 7
ADD/ALT 1
ADD/ALT 1
1/4" = 1'-0"
7
MY ZONE 1
ADD/ALT 1
1/4" = 1'-0"
8.
9.
12.
WOK MILLWORK
144"
7.
18.
8
MY ZONE - BREAKFAST
ADD/ALT 1
1/4" = 1'-0"
19.
MY ZONE 3
20.
1/4" = 1'-0"
21.
INTERIOR PAINT INFORMATION
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING FOR ADDITIONAL INFORMATION.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
> TYPE I-OP ALL INTERIOR SURFACES INDICATED TO BE PAINTED.
EGGSHELL FINISH.
COLORS TO BE SELECTED.
W.
X.
> TYPE I-OP-MD-DT MEDIUM DUTY DOOR/TRIM.
SEMI-GLOSS.
COLORS TO BE SELECTED.
> TYPE I-OP-HD HEAVY DUTY VERTICAL AND OVERHEAD
EPOXY GLOSS.
COLORS TO BE SELECTED.
> TYPE I-OP-DF DRY FALL.
FLAT.
COLORS TO BE SELECTED.
> TYPE I-TR -W TRANSPARENT FINISH ON WOOD.
Y.
Z.
>WF-1: RECLAIMED THIN WOOD
MANUFACTURER: STIKWOOD
STYLE: RECLAIMED
COLOR: MULTIPLE COLORS, TO BE SELECTED
FINISH WITH 3 COATS I-TR-W
PRODUCT MUST BE ORDERED WITH CLASS A FIRE RATED
TREATMENT OR TREATED AS SUCH ON SITE
SPECIFICATION SECTION: 06 4216 WOOD VENEER PANELING
1.
2.
3.
5.
6.
7.
8.
9.
10.
16
17
BREAKFAST BAR
18
MY ZONE 1
MY ZONE 2
PROVIDE STEEL "BEAM" OUT OF 6" TUBE
STEEL TO CONNECT WALLS. CONNECT
BEAM WITH STEEL ANGLE AND BOLT
WASHER DETAIL
NOTE 1
NOTE 1
PROVIDE STEEL
"BEAM" OUT OF 6"
TUBE STEEL TO
CONNECT WALLS
MY ZONE MILLWORK
NOTE 13
MY ZONE
MILLWORK
NOTE 25
24"
24"
24"
24"
NOTE 14, 15
24"
PLASTIC LAMINATE
CABINETS WITH
ADJUSTABLE SHELVING
NOTE 14, 15
NOTE 13
ADD/ALT 1
ADD/ALT 1
1/4" = 1'-0"
NEW SOLID SURFACE COUNTER TOP
CUT TO FIT EXISTING GLASS
LOWERATOR
SURFACE TO BE MAPLE BOARDS, FACE
BOLTED TO LAMINATE STRUCTURE. 1/4"
GAP BETWEEN BOARDS
RE USE EXISTING STRUCTURE AND
CASTERS. RE LAMINATE, AND APPLY
BOARDS AS NOTED
EXISTING MILLWORK, FIELD VERIFY DIMENSIONS
TILE BASE, TYP.
13
ADD/ALT 1
DRINKING GLASSES
1/4" = 1'-0"
11
ADD/ALT 1
14
ADD/ALT 1
CONDIMENTS 1
1/4" = 1'-0"
16 1/2"
16 1/2"
16 1/2"
16 1/2"
WALL TILE INFORMATION
NOTE 8, 25
18.
REFER TO SPECIFICATION SECTION 09 3000 TILING
NOTE 16
NOTE 8, 25
PLASTIC LAMINATE
CABINETS WITH
ADJUSTABLE SHELVING
PLASTIC LAMINATE
DIE WALL
CONSTRUCTION
PROVIDE ACCESS
PANEL FOR SINK
2" STEEL FLAT STOCK FRAMES
NOTE 14, 15
P-LAM PANELS
12
MY ZONE 6
ADD/ALT 1
1/4" = 1'-0"
2
3
I-405
I-405
3/4" PLASTIC LAMINATED FINISHED
PLYWOOD (BOTH SIDES) w/ STEEL FLAT
STOCK EDGE BANDING CONNECTED
w/ WASHER & LAG BOLT, PAINTED.
GRIND ALL EDGES SMOOTH TO TOUCH.
BEYOND.
PROVIDE 1/4" GAP BETWEEN
FLOOR FINISH & VERTICAL
PLYWOOD CONSTRUCTION, FILL
w/ CONTINUOUS SILICONE BEAD
TO SEAL JOINT AT PLYWOOD TO
FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4"
PLYWOOD SHOE SECURED TO FLOOR
(TYPICAL).
1/2" PLASTIC LAMINATED FINISHED
PLYWOOD ON 3/4" PLYWOOD
VERTICAL BLOCKING w/
PLYWOOD BASE & TOP PLATES.
SOLID SURFACE COUNTERTOP w/
MINIMUM (2) LAYERS OF 3/4" PLYWOOD
SUBSTRATE. SILICONE AT ALL COUNTER
TO VERTICAL SURFACE JOINTS.
1/4" = 1'-0"
3/4" PLYWOOD BOX BASE
CABINET. BLACK PLASTIC
LAMINATE ON ALL EXPOSED
INTERIOR MILLWORK SURFACES.
1/2" PLASTIC LAMINATED
FINISHED PLYWOOD ON
3/4" PLYWOOD FRAME
DOOR. FULL HEIGHT PIANO
HINGE w/ LOCKABLE LATCH.
>WT-5:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: LEAD
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
METAL CHANNEL AND BOLT SIZES
1/4" - 20 HEX BOLT
3/16" - WASHER
4" BAR STOCK
5" BAR STOCK
}
}
}
6"+ BAR STOCK
5" & 6" CHANNEL
}
1/2" - 13 HEX BOLT
7/16" - WASHER
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
2" BAR STOCK
2" x 2" ANGLE
PROVIDE PRESSURE TREATED 3/4"
PLYWOOD SHOE SECURED TO FLOOR
(TYPICAL).
5/16" - 18 HEX BOLT
1/4" - WASHER
3/8" - 16 HEX BOLT
5/16" - WASHER
TILE BASE, TYP.
15
ADD/ALT 1
CONDIMENTS 2
1/4" = 1'-0"
>WT-2:
MANUFACTURER: FIRECLAY TILE
STYLE: KITE
SIZE: 7-1/2" x 5-1/2"
COLOR: SEVERAL COLORS TO BE SELECTED
GROUT: 1/8" GROUT JOINTS IN MAPEI OPTICOLOR OR
SIMILAR. COLOR TO BE SELECTED.
>WT-4:
MANUFACTURER: NEMO TILE
STYLE: RAZOR
SIZE: 3/4" x 4"
COLOR: MATTE STAINLESS
GROUT: MAPEI OPTICOLOR OR SIMILAR. COLOR TO BE
SELECTED.
3/4" PLASTIC LAMINATED FINISHED
PLYWOOD (BOTH SIDES) w/ STEEL FLAT
STOCK EDGE BANDING CONNECTED
w/ WASHER & LAG BOLT, PAINTED.
GRIND ALL EDGES SMOOTH TO TOUCH.
BEYOND.
PROVIDE 1/4" GAP BETWEEN
FLOOR FINISH & VERTICAL
PLYWOOD CONSTRUCTION, FILL
w/ CONTINUOUS SILICONE BEAD
TO SEAL JOINT AT PLYWOOD TO
FLOOR (TYPICAL).
>WT-1:
MANUFACTURER: SENECA BRICK
STYLE: THIN BRICK TILE
SIZE: 2 "x 8", BRICK
COLOR: GLACIER BLEND
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-3:
MANUFACTURER: SUSAN JABLON MOSAICS
STYLE: RECYCLED
SIZE: 3/4" x 3/4"
COLOR: WHITE
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
MY ZONE 7
EXISTING STAINLESS STEEL
COLUMN SURROUND TO REMAIN.
EXISTING STAINLESS STEEL
COLUMN SURROUND TO REMAIN.
3/4" PLYWOOD BOX BASE
CABINET. BLACK PLASTIC
LAMINATE ON ALL EXPOSED
INTERIOR MILLWORK SURFACES.
1/2" PLASTIC LAMINATED
FINISHED PLYWOOD ON
3/4" PLYWOOD FRAME
DOOR. FULL HEIGHT PIANO
HINGE w/ LOCKABLE LATCH.
5
NOTE 13
1/4" = 1'-0"
SOLID SURFACE COUNTERTOP w/
MINIMUM (2) LAYERS OF 3/4" PLYWOOD
SUBSTRATE. SILICONE AT ALL COUNTER
TO VERTICAL SURFACE JOINTS.
W11
I-405
NOTE 13
2"
MY ZONE 5
1/2" PLASTIC LAMINATED FINISHED
PLYWOOD ON 3/4" PLYWOOD
VERTICAL BLOCKING w/
PLYWOOD BASE & TOP PLATES.
16.
17.
NOTE 16
I-405
10
2"
15"
1" THICK TOP
PANEL, RUN
FULL WIDTH
TO WALL
2" THICK SIDE
PANEL , RUN
FULL HEIGHT
8
MY ZONE 4
PLASTIC LAMINATE
SHELVING CUBBIES
WITH 2" THICK
SHELVES
4' - 4"
NOTE 16
NOTE 14, 15
9
13.
14.
15.
2' - 10"
MY ZONE
MILLWORK
2" 21" 2" 21" 2" 21" 2" 21"
NOTE 8, 25
2' - 10"
NOTE 25
WT-1
2"
14"
PLASTIC
LAMINATE
SHELVING
CUBBIES
NOTE 16
NOTE 25
12.
>WF-3: VINYL WALLCOVERING
MANUFACTURER: WOLF GORDON
IMAGE AND SUBSTRATE TO BE SELECTED
NOTE 1
15"
NOTE 8, 25
1' - 6"
1' - 3" 1' - 2" 1' - 3"
NOTE 8, 25
NOTE 16
11.
WT-1
4' - 4"
INTERIOR
STOREFRONT
GLASS SYSTEM,
GL-1 GLASS
12"
NOTE 1
8
I-460
>WF-2: "LIVE EDGE" WOOD
MANUFACTURER: MILLWORK
STYLE: TO MATCH EXISTING TREATMENT IN RETAIL SEATING AREA
COLOR: OAK VENEER OVER FIRE RATED PLYWOOD, CLEAR COAT
FINISH WITH 3 COATS I-TR-W
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
>WT-6:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: MOSS
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-7:
MANUFACTURER: FIRECLAY TILE
STYLE: PICKET
SIZE: 10-1/4" x 3-3/4"
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
>WT-8, WT-9, WT-10:
REFER TO TOILET ROOM SHEET
REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.
NEW
OF O J
S
TE
C N
RK
No.
16419
R E D A RC H
19.
20.
21.
22.
23.
24.
25.
GWB SOFFIT, REFER TO RCP FOR INFORMATION.
LINE OF CEILING, REFER TO RCP FOR INFORMATION.
HEAT LAMP TO BE HUNG CENTERED TO EQUIPMENT
BELOW, VERIFY WITH PLACEMENT OF EQUIPMENT PRIOR
TO INSTALLATION.
EXISTING SNEEZE GUARDS, REPAINT AND REPLACE
HARDWARE AS REQUIRED.
SOLID SURFACE COUNTERTOP WITH MINIMUM 2 LAYERS
OF 3/4" PLYWOOD SUBSTRATE ON ALL COUNTERS. REFER
TO SECTION FOR EDGE THICKNESS.
PROVIDE ADEQUATE BLOCKING AS REQUIRED.
SEAL & WATERPROOF ALL COUNTERTOP PENETRATIONS.
SILICONE @ ALL COUNTER TO VERTICAL SURFACE
JOINTS
PROVIDE COUNTER TOP CORE CUT OUT & GROMMET
COVER FOR ALL REQUIRED COUNTERTOP KITCHEN
EQUIPMENT POWER CORDS (TYPICAL).
PROVIDE HEAT PROOFING AT ALL HOT & COLD
EQUIPMENT WITHIN COUNTER SURFACE. REFER TO
DETAIL.
3/4" PLYWOOD DIEWALL CONSTRUCTION (NO
PARTICLEBOARD OR MDF), TYPICAL UNLESS OTHERWISE
NOTED.
UTILITY CHASE IN MILLWORK WITH REMOVABLE PANEL
FOR ACCESS.
TILE BASE, REFER TO FLOOR FINISH PLAN FOR TILE TYPE.
PROVIDE 1/4" GAP BETWEEN FLOOR FINISH AND
VERTICAL PLYWOOD CONSTRUCTION, FILL WITH
CONTINUOUS SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4" PLYWOOD SHOE
SECURED TO FLOOR (TYPICAL).
PROVIDE 4" HIGH SOLID SURFACE BACKSPLASH.
BLACK PLASTIC LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL UNLESS OTHERWISE
NOTED).
2x SOLID WOOD SHELF. SPECIES & FINISH TO BE SELECTED
BY ARCHITECT.
1/8" THICK STEEL FLAT STOCK TRIM SECURED WITH BOLT
AND WASHER DETAIL. FINISH TO BE SELECTED BY
ARCHITECT.
STEEL ANGLE CORNER GUARD SECURED WITH BOLT AND
WASHER DETAIL. FINISH TO BE SELECTED BY ARCHITECT.
POS, PROVIDED BY OTHERS.
VERTICAL STEEL TUBE SUPPORT. FINISH AS INDICATED.
PROVIDE 1/4" THICK SMOOTH MASONITE BACKER
BOARD FOR VINYL GRAPHIC.
2x2 STEEL FRAME WITH CLIPS TO HOLD BACKER BOARD,
WELDED AND GROUND CORNERS, FINISH AS INDICATED
AND SECURE TO WALL WITH Z CLIPS. PROVIDE BLOCKING
WITHIN WALL WHERE POSSIBLE.
SCRIBE ALL COUNTERS TIGHT TO FIT AND SILICONE GAPS
CLEANLY.
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
DRAWN BY:
AGK
CHECKED BY:
AGK
KEYED NOTES
4.
WALL FINISH INFORMATION
E
I
4.
I.
SEALED:
R EG
1/4" = 1'-0"
3
WOK 4
H.
N
2
WOK 3
TERMINATE WT-1 BRICK TILE WITH SCHLUTER STRIP AT THE
JOINT WHERE EXISTING TILE STOPS.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP
TO 12".
PROVIDE APPROPRIATE SCHLUTER EXTRUDED METAL TILE
EDGE DETAILS. CLEAR ALUMINUM.
EXISTING BRICK TO REMAIN - NO PAINT OR ADDITIONAL
WALL FINISH.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP CAP.
CONTINUE WT-1 TILE FROM EXISTING WALL INTO WORK
AREA. REMOVE CUT TILES AND REPLACE WITH NEW FULL
TILES AS REQUIRED TO BLEND IN PATTERN.
PROVIDE 2" STEEL ANGLE AS CORNER GUARD WITH 2" STEEL
FLAT STOCK AS BASE AND 2" STEEL FLAT STOCK @ 8'-0"
SECURED WITH BOLTS AND WASHERS TO STUDS.
EXISTING WALL TILE TO REMAIN.
WOOD PLANTER BOX TO REMAIN AND BE RECOVERED
WITH STEEL PLATE. REFER TO DETAILS.
PROVIDE FULL HEIGHT STEEL FLAT STOCK EDGE, REFER TO
DETAIL.
PROVIDE NEW GWB WALLS, PREP AND PAINT. COLOR TO
BE DETERMINED.
EXISTING WALLS, PREP AND PAINT, COLOR TO BE
DETERMINED.
PAINT WALLS ABOVE TO EXISTING CEILING.
PAINT NEW STAIR RAILING I-OP-HD. REFER TO
SPECIFICATION SECTION 09 9000 PAINTING FOR
ADDITIONAL INFORMATION. COLORS TO BE SELECTED.
NEW WALL TILE OVER EXISTING CMU WALL.
PROVIDE STEEL C-CHANNEL DETAILS AT BOOTH ENDS. WITH
IN CHANNEL WELD 2 CUSTOM HOOKS BENT FROM 8"
BOLTS. 1@30" AFF AND 1@60" AFF.
PAINT COLUMNS WITHIN STEEL FRAME AN ACCENT COLOR
TO BE SELECTED. PAINT COLUMNS ABOVE STEEL TO MATCH
CEILING COLOR.
GWB CEILING CLOUD. PAINT I-OP. COLORS TO BE
SELECTED.
EXISTING DOOR AND FRAME TO REMAIN. BUTT SCHLUTER
STRIP SNUGLY AGAINST FRAME AND PROVIDE CLEAN
GROUT EDGE.
PAINT EXISTING DOOR AND FRAME I-OP-MD-DT, COLORS
TO BE SELECTED.
PROVIDE SOLID SURFACE SILL/WALL CAP.
G.
SEY
ER OR
1
E.
F.
3' - 9"
WOK MILLWORK
NOTE 13
D.
MILLWORK FINISH INFORMATION
>MF-1: VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
COLOR: 3 COATS OF I-TR-W - COLOR TO BE SELECTED
>MF-2: PLASTIC LAMINATE
COLORS: TO BE SELECTED
>MF-3: SOLID SURFACE COUNTER TOP COLOR 1
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-4: SOLID SURFACE COUNTER TOP COLOR 2
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-5: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: PAINTED WITH CLEAR COAT SEALANT
>MF-6: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: BLACK
>MF-7: ORNAMENTAL METAL
EXPANDED METAL MESH
MANUFACTURER: BY MILLWORK SHOP
COLOR: TO BE SELECTED
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
GLAZING KEY
>GL-1:
STYLE: 1/4" FULLY TEMPERED GLASS
COLOR: CLEAR
>GL-2:
STYLE: CORRUGATED PLEXI GLASS
COLOR: OPAQUE
SHEET:
I-404
PHASE 2: ALTERATIONS & ADDITIONS
NOTE 25
5' - 0"
F.
RCNJ No. 2014-37-01C
WF-3
MF-6, NOTE 19
MF-6, NOTE 19
NOTE 25
E.
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
MF-6, NOTE 19
W10
7' - 3"
W10
C.
RAMAPO COLLEGE
OF NEW JERSEY
W11
B.
CT
C.
D.
TE
WT-7
W11
5' - 0"
B.
REFER TO SPECIFICATIONS 06 4100 ARCHITECTURAL
MILLWORK AND 05 7000 ORNAMENTAL METAL FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 12 3600 COUNTERTOPS
FOR ADDITIONAL INFORMATION.
ALL MILLWORK AND CABINETS SCOPE SHALL BE
CONSTRUCTED AND INSTALLED PER AWI CUSTOM GRADE
STANDARDS.
NO MDF OR PARTICLE BOARD SUBSTRATES WILL BE
ACCEPTABLE. 3/4" PLYWOOD ONLY.
ALL EXPOSED SURFACES SHALL BE THE FINISH AS NOTED ON
ELEVATIONS
ALL SEMI-EXPOSED SURFACES SHALL BE BLACK PLASTIC
LAMINATE.
INTERIOR FACE OF DIE WALLS TO BE FACED WITH BLACK
FRP.
SEAL ALL EXPOSED PLYWOOD EDGES AND MAINTAIN
MINIMUM 1/4" GAP FROM FLOOR TO PREVENT WICKING OF
WATER.
ALL SNEEZE GUARDS/ FOOD SHIELDS SHOWN SHOULD BE
INCLUDED WITHIN THE MILLWORK CONTRACTORS SCOPE OF
WORK.
ANY SIGNAGE & MENU FRAMES SHOULD BE INCLUDED
WITHIN THE MILLWORK'S SCOPE OF WORK
CONTRACTOR TO COORDINATE WITH EQUIPMENT
PROVIDER FOR INSTALLATION AND TESTING OF ALL
EQUIPMENT.
CONTRACTOR IS REQUIRED TO SET EQUIPMENT IN PLACE.
THIS INCLUDES, BUT IS NOT LIMITED TO, ALL OWNER SUPPLIED
"EXISTING" EQUIPMENT. CONTRACTOR TO VERIFY
EQUIPMENT DATA AS PROVIDED IN ELECTRICAL &
PLUMBING DRAWINGS TO MINIMIZE SLAB CORING
POSSIBLE. CONTRACTOR IS RESPONSIBLE FOR PLUMBING &
ELECTRICAL FEEDS TO EQUIPMENT.
PROVIDE P-LAM FACED VERTICAL APRON TO CONCEAL ALL
DROP IN EQUIPMENT AND SINKS. MOUNT ALL EQUIPMENT
CONTROLS TO CABINET FRAME AT APRON. SEE DETAILS.
COORDINATE LOCATIONS WITH EQUIPMENT.
INSIDE VERTICAL MILLWORK SURFACES ADJACENT TO
COOKING EQUIPMENT SHALL BE FINISHED w/ 20GA . TYPE
304 #4 MILL FINISH STAINLESS STEEL PANELS FASTENED TO
PLYWOOD BACKER. ALL JOINTS REQUIRE BATTEN STRIPS.
CONTRACTOR TO PROVIDE ENGINEERED SHOP DRAWINGS
INCLUDING PLAN LAYOUT DETAILS & SPECIFICATIONS FOR
ALL STRUCTURAL CONNECTIONS TO EXISTING BASE
BUILDING STRUCTURE FOR ARCHITECT'S REVIEW &
APPROVAL. ITEMS SHALL INCLUDE BUT NOT LIMITED TO WALL
BRACKET MOUNTING DETAILS, PICKPOINT CONNECTIONS
FOR SUSPENDED CEILING ELEMENTS, BEAM CLAMP,
UNISTRUT AND THREADED ROD DETAILS FOR EXHAUST
HOODS & OTHER SUSPENDED DESIGN ELEMENTS.
ALL EXPOSED BOLT & NUT CONNECTIONS ARE BOTH
FUNCTIONAL AND DECORATIVE. PAINT ALL FASTENERS TO
MATCH.
CALCULATE LOAD WEIGHT OF SUSPENDED OBJECTS TO
DETERMINE THE REQUIRED QUANTITY OF PICK POINT
LOCATIONS.
PROVIDE STAINLESS STEEL SUPPORT LEGS EVERY 4'-0" OR AS
REQUIRED TO AVOID DEFLECTION AND CRACKING OF
COUNTER SURFACE. SECURELY PIN LEG TO THE FLOOR AND
SEAL WITH SILICONE TO MAINTAIN WATERPROOFING BELOW
TILE. COORDINATE LOCATIONS SO AS NOT TO INTERFERE
WITH EQUIPMENT.
ALL EQUIPMENT MUST BE REVIEWED FOR HEIGHT SO AS NOT
TO INTERFERE WITH COUNTER HEIGHTS. ARCHITECT
RESERVES THE RIGHT TO CHANGE FOOT OR CASTER
SELECTION DURING SUBMITTAL TO KEEP HEIGHTS FORM
INTERFERING WITH COUNTERTOPS.
ALL CABINET DOOR HINGES TO BE CONTINUOUS PIANO
HINGES.
PROVIDE REINFORCEMENT TO COUNTERTOP EDGE OVER
LONG SPANS WHERE CUT OUTS FOR EQUIPMENT EXIST.
ALL STRUCTURAL HANGING ELEMENTS SHOULD BE RATED
FOR STRENGTH AND REVIEW IN SHOP DRAWINGS BY
STRUCTURAL ENGINEER.
ALL CUT OUTS FOR COUNTER TOP WELLS MUST HAVE
ROUNDED CORNERS PER MANUFACTURER'S INSTRUCTION.
CONTRACTOR TO VERIFY EQUIPMENT DATA AS PROVIDED
IN ELECTRICAL & PLUMBING DRAWINGS TO MINIMIZE SLAB
CORING, IF POSSIBLE.
PROVIDE HEAVY-DUTY REINFORCED CABINETS/ MILLWORK
STRUCTURE LOCATED UNDER BEVERAGE DISPENSER TYP.
THROUGH OUT PROJECT, PROVIDE P-LAM FACED VERTICAL
APRONS TO CONCEAL ALL DROP IN EQUIPMENT, SEE
DETAILS.
MOUNT ALL EQUIPMENT CONTROLS TO CABINET FRAME AT
APRON, SEE DETAILS.
SCOTT STUDENT CENTER
RESIDENTIAL DINING
3' - 3"
A.
MA
9
I-460
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL WALL
TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT ALL
WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
PAINT ALL EXPOSED CONDUIT ON WALLS. COLOR TO BE
SELECTED.
FOR SIGNAGE INFORMATION REFER TO SHEET I-460.
S TAT
3' - 3"
A.
ELEVATIONS - SERVERY
NOTE 1
EXISTING STAINLESS STEEL
COLUMN SURROUND TO REMAIN.
2' - 10"
1' - 4"
6"
MAIN LEVEL
0' - 0"
NEW
OF O J
S
TE
C N
RK
CT
No.
16419
TE
MA
S TAT
2"
2' - 10"
7' - 0"
2" 2"
PROVIDE 1/4" GAP BETWEEN
FLOOR FINISH & VERTICAL
PLYWOOD CONSTRUCTION, FILL
w/ CONTINUOUS SILICONE BEAD
TO SEAL JOINT AT PLYWOOD TO
FLOOR (TYPICAL).
E
I
PROVIDE PRESSURE TREATED 3/4"
PLYWOOD SHOE SECURED TO FLOOR
(TYPICAL).
SEALED:
R EG
2 1/4"
TILE BASE, TYP.
80°
1/2" PLASTIC LAMINATED
FINISHED PLYWOOD ON
3/4" PLYWOOD FRAME
DOOR. FULL HEIGHT PIANO
HINGE w/ LOCKABLE LATCH.
2"
PROVIDE 1/4" GAP BETWEEN
FLOOR FINISH & VERTICAL
PLYWOOD CONSTRUCTION, FILL
w/ CONTINUOUS SILICONE BEAD
TO SEAL JOINT AT PLYWOOD TO
FLOOR (TYPICAL).
2' - 3"
3/4" PLYWOOD BOX BASE
CABINET. BLACK PLASTIC
LAMINATE ON ALL EXPOSED
INTERIOR MILLWORK SURFACES.
2"
2' - 3"
1/2" PLASTIC LAMINATED
FINISHED PLYWOOD ON
3/4" PLYWOOD FRAME
DOOR. FULL HEIGHT PIANO
HINGE w/ LOCKABLE LATCH.
-0
"
R 2"
TYP.
3/4" PLASTIC LAMINATED FINISHED
PLYWOOD (BOTH SIDES) w/ STEEL FLAT
STOCK EDGE BANDING CONNECTED
w/ WASHER & LAG BOLT, PAINTED.
GRIND ALL EDGES SMOOTH TO
TOUCH. BEYOND.
1' - 0"
100°
3/4" PLYWOOD BOX BASE
CABINET. BLACK PLASTIC
LAMINATE ON ALL EXPOSED
INTERIOR MILLWORK SURFACES.
2' - 2"
R 2' - 4"
"
- 11
3'
SOLID SURFACE COUNTERTOP w/
MINIMUM (2) LAYERS OF 3/4" PLYWOOD
SUBSTRATE. SILICONE AT ALL COUNTER
TO VERTICAL SURFACE JOINTS.
N
R 1'
SOLID SURFACE COUNTERTOP w/
MINIMUM (2) LAYERS OF 3/4" PLYWOOD
SUBSTRATE. SILICONE AT ALL COUNTER
TO VERTICAL SURFACE JOINTS.
SEY
ER OR
SOLID SURFACE COUNTERTOP SHELF
R
R 1' - 11"
SOLID SURFACE COUNTERTOP w/
MINIMUM (2) LAYERS OF 3/4" PLYWOOD
SUBSTRATE. SILICONE AT ALL COUNTER
TO VERTICAL SURFACE JOINTS.
R 9"
3/4" PLASTIC LAMINATED FINISHED
PLYWOOD (BOTH SIDES) w/ STEEL FLAT
STOCK EDGE BANDING CONNECTED
w/ WASHER & LAG BOLT, PAINTED.
GRIND ALL EDGES SMOOTH TO
TOUCH. BEYOND.
1' - 2"
1' - 4"
-1
0"
2'
1/2" PLASTIC LAMINATED FINISHED
PLYWOOD ON 3/4" PLYWOOD
VERTICAL BLOCKING w/
PLYWOOD BASE & TOP PLATES.
2' - 10"
3/4" PLASTIC LAMINATED FINISHED
PLYWOOD (BOTH SIDES) w/ STEEL FLAT
STOCK EDGE BANDING CONNECTED
w/ WASHER & LAG BOLT, PAINTED.
GRIND ALL EDGES SMOOTH TO
TOUCH. BEYOND.
SOLID SURFACE COUNTERTOP SHELF
1/2" PLASTIC LAMINATED FINISHED
PLYWOOD ON 3/4" PLYWOOD
VERTICAL BLOCKING w/
PLYWOOD BASE & TOP PLATES.
2' - 10"
2"
EXISTING STAINLESS STEEL
COLUMN SURROUND TO
REMAIN. VERIFY EXISTING
DIMENSIONS IN FIELD.
3"
1/2" PLASTIC LAMINATED FINISHED
PLYWOOD ON 3/4" PLYWOOD
VERTICAL BLOCKING w/
PLYWOOD BASE & TOP PLATES.
6"
4" DIAMETER CORE CUT IN SOLID SURFACE
FOR STAINLESS STEEL UTENSIL HOLDERS,
TYPICAL FOR (14). PROVIDE ADEQUATE
BLOCKING, SEALANT & WATERPROOFING
@ ALL COUNTERTOP PENETRATIONS.
EXISTING STAINLESS STEEL
COLUMN SURROUND TO REMAIN.
2' - 2"
3/23/2016 6:22:45 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
R E D A RC H
I
MAIN LEVEL
0' - 0"
TILE BASE, TYP.
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
PROVIDE PRESSURE TREATED 3/4"
PLYWOOD SHOE SECURED TO FLOOR
(TYPICAL).
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1
CONDIMENT PLAN
ADD/ALT 1
2
ADD/ALT 1
3/4" = 1'-0"
3
CONDIMENT SECTION A
ADD/ALT 1
3/4" = 1'-0"
CONDIMENT SECTION B
3/4" = 1'-0"
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
TO MATCH EXISTING
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
EXISTING WALL FINISH TO REMAIN
SOLID SURFACE COUNTERTOP ON (2)
LAYERS OF 3/4" PLYWOOD SUBSTRATE
ON COUNTERS DEEPER THEN 30", REFER
TO I-103 FOR COUNTERTOP DEPTHS.
REVISIONS
4" SOLID SURFACE BACK SPLASH
4"
SOLID SURFACE COUNTERTOP ON 2
LAYERS OF 3/4" PLYWOOD SUBSTRATE
2"
2"
4" SOLID SURFACE BACKSPLASH
PROVIDE ADEQUATE BLOCKING
WHERE REQUIRED
ADEQUATE BLOCKING FOR
DOOR STOP & FRAME
5"
ADD/ALT 1
1 1/2" = 1'-0"
BEVERAGE STATION SECTION
1 1/2" = 1'-0"
MOLD & MILDEW RESISTANT 100%
SILICONE CAULK, ALL SIDES
KITCHEN EQUIPMENT, REFER TO PLANS
4 7/8"
1/8" MIN RADIUSED EDGES
10' - 0"
PAINTED 5/8" GYPSUM WALL
BOARD ON 3 5/8" 20 Ga. METAL
STUDS FRAMING @ 16" O.C.
ATTACHED TO DECK ABOVE w/
THREADED ROD. REFER TO DETAIL 3 / I-202
SOLID SURFACE COUNTERTOP
SOLID SURFACE COUNTERTOP ON (2)
LAYERS OF 3/4" PLYWOOD SUBSTRATE
ON COUNTERS DEEPER THEN 30", REFER
TO I-103 FOR COUNTERTOP DEPTHS.
NEW WALL TILE, REFER TO I-404
SOLID SURFACE
COUNTERTOP SUBSTRATE,
(2) LAYERS 3/4" PLYWOOD
EXISTING WALL TO REMAIN
SOLID SURFACE COUNTERTOP
OPENING SUPPORT, REFER TO
MANUFACTURES
RECOMMENDATIONS
2"
ADEQUATE BLOCKING
WHERE REQUIRED
3' - 0"
STAINED SOLID WOOD PLANKING
w/ VARIABLE WIDTHS, DEEPS, &
LENGTHS. COORDINATE w/
ARCHITECT FOR SIZES & FINISH.
LOW PROFILE
LOCKABLE CABINET
HARDWARE HANDLE
1/4" MIN.
1/8" MIN
EXPANSION CLEARANCE
1.
2.
3.
4.
PROVIDE ADEQUATE BLOCKING
WHERE REQUIRED
TO BE PROVIDED BY MILLWORKER
THIS DETAIL TO BE PROVIDED @ ALL EQUIPMENT OPENING CUTOUTS
ALL CUT OPENING CORNERS TO BE RADIUSED PER MANUFACTURER'S RECOMMENDATIONS
REFER TO EQUIPMENT MANUFACTURER'S RECOMMENDATIONS FOR EQUIPMENT CUT SIZES & INSTALLATION INSTRUCTIONS
2' - 2"
OVERLAY CABINET DOORS LAMINATE ON 3/4" PLYWOOD
WITH PIANO HINGES AND
MAGNETIC HOLDS (TYPICAL)
3M NEOPRENE TAPE (MIN THICKNESS OF
1.2 mm), KAOWOOL TAPE (MIN
THICKNESS OF 2 mm), NOMEX TAPE (MIN
THICKNESS OF 2.79 mm), OR EQUAL.
WRAP COMPLETE OPENING. REFER TO
MANUFACTURES RECOMMENDATIONS.
GENERAL NOTES:
*TYPICAL FOR ALL CUT OPENINGS WITHIN SOLID SURFACE COUNTERTOPS
DECORATIVE FINISH ON FACE
OF CABINET, REFER TO
ELEVATIONS FOR FINISH
4" CURVED CHANNEL, PAINTED.
SUSPENDED FROM GYPSUM
CEILING CLOUD ABOVE w/
THREADED ROD & BEAM CLAMPS
4" SOLID SURFACE BACKSPLASH
ALUMINUM TAPE, MIN THICKNESS OF 0.13
mm. OVERLAP COMPLETE OPENING. MIN
1/4" PAST BASE TAPE.
RAMAPO COLLEGE
OF NEW JERSEY
CONDIMENT ISLAND
6
MY ZONE DIEWALL
SERVERY - DETAILS
6"
ADEQUATE BLOCKING FOR
DOOR STOP & FRAME
ADJUSTABLE SHELVING
SHEET STEEL PANELS ON CURVED
2"x2" STEEL TUBE ATTACHED w/ 5/16"
HEX BOLT & 1/4" WASHER, PAINTED.
SUSPENDED FROM FLOOR DECK
ABOVE w/ THREADED ROD. GRIND
ALL EDGES SMOOTH TO TOUCH.
3/4" PLYWOOD BOX CABINET w/
PLAM ON ALL SIDES. BLACK PLASTIC
LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL
UNLESS OTHERWISE NOTED).
9
ADD/ALT 1
EQUIPMENT TO SOLID SURFACE CONNECTION DETAIL
6" = 1'-0"
TILE BASE, TYP.
6"
7' - 0"
PROVIDE 1/4" GAP BETWEEN
FLOOR FINISH & VERTICAL
PLYWOOD CONSTRUCTION, FILL
w/ CONTINUOUS SILICONE BEAD
TO SEAL JOINT AT PLYWOOD TO
FLOOR (TYPICAL).
PENDANT LIGHTING
FLOOR FINISH, REFER TO I-102
PROVIDE PRESSURE TREATED 3/4"
PLYWOOD SHOE SECURED TO FLOOR
(TYPICAL).
METAL CHANNEL AND BOLT SIZES
1/4" - 20 HEX BOLT
3/16" - WASHER
4" BAR STOCK
5" BAR STOCK
}
}
}
6"+ BAR STOCK
5" & 6" CHANNEL
}
1/2" - 13 HEX BOLT
7/16" - WASHER
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
2" BAR STOCK
2" x 2" ANGLE
7
ADD/ALT 1
WOK CLOUD SECTION
1 1/2" = 1'-0"
8
ADD/ALT 1
TYPICAL COUNTER AT WALL
1 1/2" = 1'-0"
5/16" - 18 HEX BOLT
1/4" - WASHER
3/8" - 16 HEX BOLT
5/16" - WASHER
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
I-405
PHASE 2: ALTERATIONS & ADDITIONS
2"
2"
EXISTING CABINET BASE &
FRAME TO REMAIN
RCNJ No. 2014-37-01C
7"
PROVIDE PRESSURE TREATED 3/4"
PLYWOOD SHOE SECURED TO FLOOR
(TYPICAL).
4
JNC
OVERLAY CABINET DOORS - LAMINATE ON
3/4" PLYWOOD WITH PIANO HINGES AND
MAGNETIC HOLDS (TYPICAL)
MAIN LEVEL
0' - 0"
ADD/ALT 1
CHECKED BY:
DECORATIVE FINISH ON FACE OF CABINET,
TO BE DETERMINED BY ARCHITECT
TILE BASE, TYP.
5
JNC
SCOTT STUDENT CENTER
RESIDENTIAL DINING
2" PAINTED STEEL FLAT STOCK
(GRIND ALL EDGES SMOOTH TO
TOUCH) w/ HEX BOLT & WASHER
(PAINTED TO MATCH FLAT STOCK)
PROVIDE 1/4" GAP BETWEEN FLOOR
FINISH & VERTICAL PLYWOOD
CONSTRUCTION, FILL w/ CONTINUOUS
SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PAINTED 5/8" GYPSUM WALL BOARD
(BOTH SIDES) ON 3 5/8" METAL STUDS
FRAMING @ 16" O.C.
1' - 10"
2' - 10"
3/4" PLYWOOD DIEWALL
CONSTRUCTION (NO PARTICLEBOARD
OR MDF) w/ PLASTIC LAMINATE FINISH
DRAWN BY:
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
2" PAINTED STEEL FLAT STOCK
(GRIND ALL EDGES SMOOTH TO
TOUCH) w/ HEX BOLT & WASHER
(PAINTED TO MATCH FLAT STOCK)
3/23/2016 6:23:02 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
I
5
13
I-411
CT
R E D A RC H
I
EXISTING DISH DROP OPENING
10
2
11
LOWER LEVEL 1
TE
No.
16419
TE
R EG
S
C N
RK
N
MA
E
NEW
OF O J
SEY
ER OR
S TAT
SEALED:
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
SOLID SURFACE COUNTER TOP
I-411
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
I-452
ARCHITECT:
I-411
9
8
12
I-411
I-411
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
7
I-411
6
ROUND BOOTH
1
4
ENGINEER:
I-451
5
SOLID SURFACE TRANSACTION TOP
SOLID SURFACE COUNTER TOP
116
NEW TILE (WT-4) OVER EXISTING
COLUMN SURROUND
NEW TILE (WT-4) OVER EXISTING
COLUMN SURROUND
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
EXISTING PLANTER, REFER TO
DETAILS FOR RESURFACING
REVISIONS
4
I-411
I-451
I-411
14
6
4
FURNITURE BY OTHERS
LOWER LEVEL 4
DRAWN BY:
AGK
CHECKED BY:
AGK
NEW HANDRAILS
I-412
2
3
FURNITURE BY OTHERS
I-452
3
I-451
5
FURNITURE BY OTHERS
I-451
3
BUILT-IN COUNTERS, REFER
TO DETAILS
I-412
NEW TILE (WT-4)OVER
EXISTING COLUMN
SURROUND
EXISTING PLANTER, REFER TO
DETAILS FOR RESURFACING
I-412
4
3
LOWER LEVEL 2
106
FURNITURE BY OTHERS
I-412
7
FURNITURE BY OTHERS
FURNITURE BY OTHERS
FURNITURE BY OTHERS
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
1
RESIDENTIAL SEATING AREA PLAN
1/4" = 1'-0"
2
LOWER LEVEL 3
I-410
PHASE 2: ALTERATIONS & ADDITIONS
BUILT-IN COUNTERS, REFER
TO DETAILS
RCNJ No. 2014-37-01C
6
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
I-412
RAMAPO COLLEGE
OF NEW JERSEY
5
SCOTT STUDENT CENTER
RESIDENTIAL DINING
I-412
RESIDENTIAL DINING BASE BID
ENLARGED PLAN
1
3
UPPER LEVEL
UPPER LEVEL 2
WOOD OVERHEAD
CONSTRUCTION, REFER TO RCP
70" TV, BY OWNER. PROVIDE
POWER AND DATA
WT-2
6" FLAT STOCK STEEL FRAME ON WALL BEYOND
NOTE 1
NOTE 1
NOTE 2
NOTE 2
4
W5
2x2 STEEL FRAME,
CLEAR COATED
I-202
GWB WALL ABOVE, PAINTED
1
I-451
WT-2
1
70" TV, BY OWNER. PROVIDE
POWER AND DATA
6" STEEL SQUARE COLUMNS
6"
M.
N.
I-452
SOFFIT ABOVE, PAINTED
SOFFIT ABOVE, PAINTED
6"
O.
EXISTING BEAM
2
I-460
W7, NOTE 20
MF-4
P.
7' - 0"
Q.
R.
4' - 4"
42"
WF-3
MF-7
W21
W11
W3
WT-1
POCKET DOOR
FOR SECURITY
GATE
PAINT DOOR
AND FRAME
WIRE PULLS
HOST STATION
MF-3
TILE BASE
NOTE17
PLASTIC LAMINATE
CABINETS WITH
ADJUSTABLE SHELVING
INSIDE
MF-1
NOTE 13
WRAP MF-1
AROUND CORNER
NOTE 5, MF-4
6" STEEL SQUARE COLUMNS
TILE WALL BASE, TYP
MF-7
STEEL FRAME AND METAL
MESH SCREENS
6" FLAT STOCK STEEL FRAME,
NOTE 19
W21
S.
W11
W7, NOTE 20
T.
U.
V.
4
5
ELEVATION AT DOOR TO RETAIL
6
HOST DESK
BACK OF HOST
W.
1/4" = 1'-0"
1/4" = 1'-0"
1/4" = 1'-0"
X.
WT-2
2
11
I-460
SIZE STEEL TO COVER TILE WORK
NOTE 1
I-452
Y.
NOTE 23, 24
12"
3
I-460
8' - 0"
MF-3,
NOTE 5
NOTE 7, 25
48"
8' - 0"
NOTE 19, MF-6
WF-3
NOTE 1
NOTE 1
MF-6, NOTE 19
MF-6, NOTE 19
WT-1
WT-1
Z.
KEYED NOTES
10' - 0"
14"
NOTE 18
NOTE 19, MF-6
1.
2.
3.
MF-3, NOTE 5
NOTE 25
MF-1
26"
34"
24"
4.
4' - 0"
6"
7' - 2"
2" CLEAR COATED STEEL
FRAMED CABINET WITH
GLASS DOORS (GL-1)AND
MAPLE SHELVING WITHIN
5.
6.
7.
8.
SOLID MAPLE DOORS ON PIANO
HINGES WITH BOLT AND WASHER PULLS
9.
NOTE 13
10.
7
8
FRUIT STAND FRONT
1/4" = 1'-0"
9
FRUIT STAND, SIDE 1
1/4" = 1'-0"
WT-1
12.
13.
14.
NOTE 1
WT-1
NOTE 1
MF-6
MF-6
WT-1
15.
16.
17.
MF-6
WT-1
NOTE 19
18.
WF-3
19.
NOTE 23, 24
6' - 8"
8' - 6"
10' - 0"
1/4" = 1'-0"
W1
I-452
1' - 0"
NOTE 19
11.
W8
2
NOTE 1
FRUIT STAND SIDE 2
20.
W19, W20
4
I-460
24.
EXISTING DISH DROP SURROUND TO REMAIN
10
11
FRUIT STAND - INSIDE BACK
12
FRUIT STAND BACK
1/4" = 1'-0"
21.
22.
23.
1/4" = 1'-0"
13
FRUIT STAND INSIDE
25.
GWB SOFFIT, REFER TO RCP FOR INFORMATION.
LINE OF CEILING, REFER TO RCP FOR INFORMATION.
HEAT LAMP TO BE HUNG CENTERED TO EQUIPMENT
BELOW, VERIFY WITH PLACEMENT OF EQUIPMENT PRIOR
TO INSTALLATION.
EXISTING SNEEZE GUARDS, REPAINT AND REPLACE
HARDWARE AS REQUIRED.
SOLID SURFACE COUNTERTOP WITH MINIMUM 2 LAYERS
OF 3/4" PLYWOOD SUBSTRATE ON ALL COUNTERS. REFER
TO SECTION FOR EDGE THICKNESS.
PROVIDE ADEQUATE BLOCKING AS REQUIRED.
SEAL & WATERPROOF ALL COUNTERTOP PENETRATIONS.
SILICONE @ ALL COUNTER TO VERTICAL SURFACE
JOINTS
PROVIDE COUNTER TOP CORE CUT OUT & GROMMET
COVER FOR ALL REQUIRED COUNTERTOP KITCHEN
EQUIPMENT POWER CORDS (TYPICAL).
PROVIDE HEAT PROOFING AT ALL HOT & COLD
EQUIPMENT WITHIN COUNTER SURFACE. REFER TO
DETAIL.
3/4" PLYWOOD DIEWALL CONSTRUCTION (NO
PARTICLEBOARD OR MDF), TYPICAL UNLESS OTHERWISE
NOTED.
UTILITY CHASE IN MILLWORK WITH REMOVABLE PANEL
FOR ACCESS.
TILE BASE, REFER TO FLOOR FINISH PLAN FOR TILE TYPE.
PROVIDE 1/4" GAP BETWEEN FLOOR FINISH AND
VERTICAL PLYWOOD CONSTRUCTION, FILL WITH
CONTINUOUS SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4" PLYWOOD SHOE
SECURED TO FLOOR (TYPICAL).
PROVIDE 4" HIGH SOLID SURFACE BACKSPLASH.
BLACK PLASTIC LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL UNLESS OTHERWISE
NOTED).
2x SOLID WOOD SHELF. SPECIES & FINISH TO BE SELECTED
BY ARCHITECT.
1/8" THICK STEEL FLAT STOCK TRIM SECURED WITH BOLT
AND WASHER DETAIL. FINISH TO BE SELECTED BY
ARCHITECT.
STEEL ANGLE CORNER GUARD SECURED WITH BOLT AND
WASHER DETAIL. FINISH TO BE SELECTED BY ARCHITECT.
POS, PROVIDED BY OTHERS.
VERTICAL STEEL TUBE SUPPORT. FINISH AS INDICATED.
PROVIDE 1/4" THICK SMOOTH MASONITE BACKER
BOARD FOR VINYL GRAPHIC.
2x2 STEEL FRAME WITH CLIPS TO HOLD BACKER BOARD,
WELDED AND GROUND CORNERS, FINISH AS INDICATED
AND SECURE TO WALL WITH Z CLIPS. PROVIDE BLOCKING
WITHIN WALL WHERE POSSIBLE.
SCRIBE ALL COUNTERS TIGHT TO FIT AND SILICONE GAPS
CLEANLY.
TOWARD DISH RETURN
1/4" = 1'-0"
1/4" = 1'-0"
MILLWORK FINISH INFORMATION
PROVIDE NEW CLEAN WALL
SURFACE ABOVE WHERE
CEILING GETS REMOVED
2' - 6"
2"
6"
2"
9"
2"
10"
2"
4
W4
I-451
WT-4
2"
33"
2"
33"
2"
33"
2"
33"
2"
33"
2"
33"
2"
33"
2"
33"
2" SQUARE TUBE FRAME
2"
2" SQUARE TUBE UPRIGHTS TO BE
CONNECTED INSIDE THE EXISTING
PLANTER. FIELD VERIFY PLANTER
CONDITIONS FOR CONNECTION
10"
MF-5 w/
MF-7 INSERT
EXPANDED METAL MESH SCREEN
WT-4
W9
EXISTING PLANTER RE-CLAD IN STEEL
W4
TOWARDS SEATING AREA
1/4" = 1'-0"
1/4" - 20 HEX BOLT
3/16" - WASHER
4" BAR STOCK
5" BAR STOCK
}
}
}
6"+ BAR STOCK
5" & 6" CHANNEL
}
1/2" - 13 HEX BOLT
7/16" - WASHER
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
2" BAR STOCK
2" x 2" ANGLE
EXISTING BRICK WALLS
15
I-411
14
METAL CHANNEL AND BOLT SIZES
W14
15
PLANTER SCREEN DETAIL
1/2" = 1'-0"
5/16" - 18 HEX BOLT
1/4" - WASHER
3/8" - 16 HEX BOLT
5/16" - WASHER
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
>MF-1: VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
COLOR: 3 COATS OF I-TR-W - COLOR TO BE SELECTED
>MF-2: PLASTIC LAMINATE
COLORS: TO BE SELECTED
>MF-3: SOLID SURFACE COUNTER TOP COLOR 1
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-4: SOLID SURFACE COUNTER TOP COLOR 2
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-5: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: PAINTED WITH CLEAR COAT SEALANT
>MF-6: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: BLACK
>MF-7: ORNAMENTAL METAL
EXPANDED METAL MESH
MANUFACTURER: BY MILLWORK SHOP
COLOR: TO BE SELECTED
GLAZING KEY
>GL-1:
STYLE: 1/4" FULLY TEMPERED GLASS
COLOR: CLEAR
>GL-2:
STYLE: CORRUGATED PLEXI GLASS
COLOR: OPAQUE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
TERMINATE WT-1 BRICK TILE WITH SCHLUTER STRIP AT THE
JOINT WHERE EXISTING TILE STOPS.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP
TO 12".
PROVIDE APPROPRIATE SCHLUTER EXTRUDED METAL TILE
EDGE DETAILS. CLEAR ALUMINUM.
EXISTING BRICK TO REMAIN - NO PAINT OR ADDITIONAL
WALL FINISH.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP CAP.
CONTINUE WT-1 TILE FROM EXISTING WALL INTO WORK
AREA. REMOVE CUT TILES AND REPLACE WITH NEW FULL
TILES AS REQUIRED TO BLEND IN PATTERN.
PROVIDE 2" STEEL ANGLE AS CORNER GUARD WITH 2" STEEL
FLAT STOCK AS BASE AND 2" STEEL FLAT STOCK @ 8'-0"
SECURED WITH BOLTS AND WASHERS TO STUDS.
EXISTING WALL TILE TO REMAIN.
WOOD PLANTER BOX TO REMAIN AND BE RECOVERED
WITH STEEL PLATE. REFER TO DETAILS.
PROVIDE FULL HEIGHT STEEL FLAT STOCK EDGE, REFER TO
DETAIL.
PROVIDE NEW GWB WALLS, PREP AND PAINT. COLOR TO
BE DETERMINED.
EXISTING WALLS, PREP AND PAINT, COLOR TO BE
DETERMINED.
PAINT WALLS ABOVE TO EXISTING CEILING.
PAINT NEW STAIR RAILING I-OP-HD. REFER TO
SPECIFICATION SECTION 09 9000 PAINTING FOR
ADDITIONAL INFORMATION. COLORS TO BE SELECTED.
NEW WALL TILE OVER EXISTING CMU WALL.
PROVIDE STEEL C-CHANNEL DETAILS AT BOOTH ENDS. WITH
IN CHANNEL WELD 2 CUSTOM HOOKS BENT FROM 8"
BOLTS. 1@30" AFF AND 1@60" AFF.
PAINT COLUMNS WITHIN STEEL FRAME AN ACCENT COLOR
TO BE SELECTED. PAINT COLUMNS ABOVE STEEL TO MATCH
CEILING COLOR.
GWB CEILING CLOUD. PAINT I-OP. COLORS TO BE
SELECTED.
EXISTING DOOR AND FRAME TO REMAIN. BUTT SCHLUTER
STRIP SNUGLY AGAINST FRAME AND PROVIDE CLEAN
GROUT EDGE.
PAINT EXISTING DOOR AND FRAME I-OP-MD-DT, COLORS
TO BE SELECTED.
PROVIDE SOLID SURFACE SILL/WALL CAP.
SEALED:
E
NEW
OF O J
S
TE
C N
RK
N
2
HOST DESK
REFER TO WALL FINISH PLAN.
THE PREFIX "W" INDICATES WALL FINISH NOTE.
I
1
L.
WALL FINISH KEYED NOTES
R EG
K.
G.
SEY
ER OR
J.
F.
No.
16419
R E D A RC H
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
INTERIOR PAINT INFORMATION
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING FOR ADDITIONAL INFORMATION.
> TYPE I-OP ALL INTERIOR SURFACES INDICATED TO BE PAINTED.
EGGSHELL FINISH.
COLORS TO BE SELECTED.
> TYPE I-OP-MD-DT MEDIUM DUTY DOOR/TRIM.
SEMI-GLOSS.
COLORS TO BE SELECTED.
DRAWN BY:
AGK
CHECKED BY:
AGK
> TYPE I-OP-HD HEAVY DUTY VERTICAL AND OVERHEAD
EPOXY GLOSS.
COLORS TO BE SELECTED.
> TYPE I-OP-DF DRY FALL.
FLAT.
COLORS TO BE SELECTED.
> TYPE I-TR -W TRANSPARENT FINISH ON WOOD.
WALL FINISH INFORMATION
>WF-1: RECLAIMED THIN WOOD
MANUFACTURER: STIKWOOD
STYLE: RECLAIMED
COLOR: MULTIPLE COLORS, TO BE SELECTED
FINISH WITH 3 COATS I-TR-W
PRODUCT MUST BE ORDERED WITH CLASS A FIRE RATED
TREATMENT OR TREATED AS SUCH ON SITE
SPECIFICATION SECTION: 06 4216 WOOD VENEER PANELING
>WF-2: "LIVE EDGE" WOOD
MANUFACTURER: MILLWORK
STYLE: TO MATCH EXISTING TREATMENT IN RETAIL SEATING AREA
COLOR: OAK VENEER OVER FIRE RATED PLYWOOD, CLEAR COAT
FINISH WITH 3 COATS I-TR-W
>WF-3: VINYL WALLCOVERING
MANUFACTURER: WOLF GORDON
IMAGE AND SUBSTRATE TO BE SELECTED
WALL TILE INFORMATION
REFER TO SPECIFICATION SECTION 09 3000 TILING
>WT-1:
MANUFACTURER: SENECA BRICK
STYLE: THIN BRICK TILE
SIZE: 2 "x 8", BRICK
COLOR: GLACIER BLEND
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-2:
MANUFACTURER: FIRECLAY TILE
STYLE: KITE
SIZE: 7-1/2" x 5-1/2"
COLOR: SEVERAL COLORS TO BE SELECTED
GROUT: 1/8" GROUT JOINTS IN MAPEI OPTICOLOR OR
SIMILAR. COLOR TO BE SELECTED.
>WT-3:
MANUFACTURER: SUSAN JABLON MOSAICS
STYLE: RECYCLED
SIZE: 3/4" x 3/4"
COLOR: WHITE
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-4:
MANUFACTURER: NEMO TILE
STYLE: RAZOR
SIZE: 3/4" x 4"
COLOR: MATTE STAINLESS
GROUT: MAPEI OPTICOLOR OR SIMILAR. COLOR TO BE
SELECTED.
>WT-5:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: LEAD
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-6:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: MOSS
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-7:
MANUFACTURER: FIRECLAY TILE
STYLE: PICKET
SIZE: 10-1/4" x 3-3/4"
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
>WT-8, WT-9, WT-10:
REFER TO TOILET ROOM SHEET
REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
I-411
PHASE 2: ALTERATIONS & ADDITIONS
I.
E.
RCNJ No. 2014-37-01C
H.
C.
D.
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
G.
B.
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL WALL
TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT ALL
WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
PAINT ALL EXPOSED CONDUIT ON WALLS. COLOR TO BE
SELECTED.
FOR SIGNAGE INFORMATION REFER TO SHEET I-460.
RAMAPO COLLEGE
OF NEW JERSEY
F.
A.
CT
E.
REFER TO SPECIFICATIONS 06 4100 ARCHITECTURAL
MILLWORK AND 05 7000 ORNAMENTAL METAL FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 12 3600 COUNTERTOPS
FOR ADDITIONAL INFORMATION.
ALL MILLWORK AND CABINETS SCOPE SHALL BE
CONSTRUCTED AND INSTALLED PER AWI CUSTOM GRADE
STANDARDS.
NO MDF OR PARTICLE BOARD SUBSTRATES WILL BE
ACCEPTABLE. 3/4" PLYWOOD ONLY.
ALL EXPOSED SURFACES SHALL BE THE FINISH AS NOTED ON
ELEVATIONS
ALL SEMI-EXPOSED SURFACES SHALL BE BLACK PLASTIC
LAMINATE.
INTERIOR FACE OF DIE WALLS TO BE FACED WITH BLACK
FRP.
SEAL ALL EXPOSED PLYWOOD EDGES AND MAINTAIN
MINIMUM 1/4" GAP FROM FLOOR TO PREVENT WICKING OF
WATER.
ALL SNEEZE GUARDS/ FOOD SHIELDS SHOWN SHOULD BE
INCLUDED WITHIN THE MILLWORK CONTRACTORS SCOPE OF
WORK.
ANY SIGNAGE & MENU FRAMES SHOULD BE INCLUDED
WITHIN THE MILLWORK'S SCOPE OF WORK
CONTRACTOR TO COORDINATE WITH EQUIPMENT
PROVIDER FOR INSTALLATION AND TESTING OF ALL
EQUIPMENT.
CONTRACTOR IS REQUIRED TO SET EQUIPMENT IN PLACE.
THIS INCLUDES, BUT IS NOT LIMITED TO, ALL OWNER SUPPLIED
"EXISTING" EQUIPMENT. CONTRACTOR TO VERIFY
EQUIPMENT DATA AS PROVIDED IN ELECTRICAL &
PLUMBING DRAWINGS TO MINIMIZE SLAB CORING
POSSIBLE. CONTRACTOR IS RESPONSIBLE FOR PLUMBING &
ELECTRICAL FEEDS TO EQUIPMENT.
PROVIDE P-LAM FACED VERTICAL APRON TO CONCEAL ALL
DROP IN EQUIPMENT AND SINKS. MOUNT ALL EQUIPMENT
CONTROLS TO CABINET FRAME AT APRON. SEE DETAILS.
COORDINATE LOCATIONS WITH EQUIPMENT.
INSIDE VERTICAL MILLWORK SURFACES ADJACENT TO
COOKING EQUIPMENT SHALL BE FINISHED w/ 20GA . TYPE
304 #4 MILL FINISH STAINLESS STEEL PANELS FASTENED TO
PLYWOOD BACKER. ALL JOINTS REQUIRE BATTEN STRIPS.
CONTRACTOR TO PROVIDE ENGINEERED SHOP DRAWINGS
INCLUDING PLAN LAYOUT DETAILS & SPECIFICATIONS FOR
ALL STRUCTURAL CONNECTIONS TO EXISTING BASE
BUILDING STRUCTURE FOR ARCHITECT'S REVIEW &
APPROVAL. ITEMS SHALL INCLUDE BUT NOT LIMITED TO WALL
BRACKET MOUNTING DETAILS, PICKPOINT CONNECTIONS
FOR SUSPENDED CEILING ELEMENTS, BEAM CLAMP,
UNISTRUT AND THREADED ROD DETAILS FOR EXHAUST
HOODS & OTHER SUSPENDED DESIGN ELEMENTS.
ALL EXPOSED BOLT & NUT CONNECTIONS ARE BOTH
FUNCTIONAL AND DECORATIVE. PAINT ALL FASTENERS TO
MATCH.
CALCULATE LOAD WEIGHT OF SUSPENDED OBJECTS TO
DETERMINE THE REQUIRED QUANTITY OF PICK POINT
LOCATIONS.
PROVIDE STAINLESS STEEL SUPPORT LEGS EVERY 4'-0" OR AS
REQUIRED TO AVOID DEFLECTION AND CRACKING OF
COUNTER SURFACE. SECURELY PIN LEG TO THE FLOOR AND
SEAL WITH SILICONE TO MAINTAIN WATERPROOFING BELOW
TILE. COORDINATE LOCATIONS SO AS NOT TO INTERFERE
WITH EQUIPMENT.
ALL EQUIPMENT MUST BE REVIEWED FOR HEIGHT SO AS NOT
TO INTERFERE WITH COUNTER HEIGHTS. ARCHITECT
RESERVES THE RIGHT TO CHANGE FOOT OR CASTER
SELECTION DURING SUBMITTAL TO KEEP HEIGHTS FORM
INTERFERING WITH COUNTERTOPS.
ALL CABINET DOOR HINGES TO BE CONTINUOUS PIANO
HINGES.
PROVIDE REINFORCEMENT TO COUNTERTOP EDGE OVER
LONG SPANS WHERE CUT OUTS FOR EQUIPMENT EXIST.
ALL STRUCTURAL HANGING ELEMENTS SHOULD BE RATED
FOR STRENGTH AND REVIEW IN SHOP DRAWINGS BY
STRUCTURAL ENGINEER.
ALL CUT OUTS FOR COUNTER TOP WELLS MUST HAVE
ROUNDED CORNERS PER MANUFACTURER'S INSTRUCTION.
CONTRACTOR TO VERIFY EQUIPMENT DATA AS PROVIDED
IN ELECTRICAL & PLUMBING DRAWINGS TO MINIMIZE SLAB
CORING, IF POSSIBLE.
PROVIDE HEAVY-DUTY REINFORCED CABINETS/ MILLWORK
STRUCTURE LOCATED UNDER BEVERAGE DISPENSER TYP.
THROUGH OUT PROJECT, PROVIDE P-LAM FACED VERTICAL
APRONS TO CONCEAL ALL DROP IN EQUIPMENT, SEE
DETAILS.
MOUNT ALL EQUIPMENT CONTROLS TO CABINET FRAME AT
APRON, SEE DETAILS.
TE
D.
GENERAL NOTES
SCOTT STUDENT CENTER
RESIDENTIAL DINING
C.
GENERAL NOTES
MA
B.
WALL FINISHES
S TAT
A.
INTERIOR|ELEVATIONS
INTERIOR ELEVATIONS
3/23/2016 6:23:15 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
(2) STEEL C-CHANNEL, WELDED
AND BOLTED TO COLUMNS
(2) STEEL C-CHANNEL, WELDED
AND BOLTED TO COLUMNS
MILLWORK OVERHEAD STRUCTURE
MILLWORK OVERHEAD STRUCTURE
INTERIOR|ELEVATIONS
GENERAL NOTES
GENERAL NOTES
I-451
F.
G.
B.
C.
D.
E.
F.
W4
WALL FINISH KEYED NOTES
REFER TO WALL FINISH PLAN.
THE PREFIX "W" INDICATES WALL FINISH NOTE.
I-451
1.
WT-1
NOTE 22
W4
8
I-412
NEW STAIR SYSTEM, FINISH AS SCHEDULED
W14
SOLID SURFACE
COUNTER TOP
NEW STAIR SYSTEM
1
2
TOWARDS STAIRS
1/4" = 1'-0"
GWB WALLS, PAINTED
FURNITURE BY OTHERS
STEEL FLAT STOCK
TRIM AROUND BASE
STEEL FLAT STOCK ON
SIDES AND TOP OF
WALLS
NOTE 22
GWB WALLS, PAINTED
WT-1
STEEL FLAT STOCK
TRIM AROUND BASE
SOLID SURFACE
COUNTER TOP
STEEL FLAT STOCK ON SIDES
AND TOP OF WALLS
3
TOWARDS BOOTH SEATING
TOWARDS BOOTH SEATING 2
1/4" = 1'-0"
SOLID SURFACE
WALL CAP
4.
WALL BASE
5.
6.
EXISTING RAMP,
RESURFACED.
PAINT EXISTING
HANDRAIL
7.
8.
9.
1/4" = 1'-0"
10.
STRUCTURE ABOVE, PAINTED
11.
WALL ABOVE, PAINTED
12.
WINDOW SYSTEM ABOVE
13.
14.
WINDOW SYSTEM ABOVE
15.
16.
WALL ABOVE, PAINTED
STRUCTURE ABOVE,
PAINTED
17.
W4
18.
19.
EXPANDED METAL ROOM
DIVIDER SCREENS MF-5, MF-7
PAINTED GWB COLUMN
PAINTED GWB
PAINTED SURFACE ABOVE
PAINTED SURFACE ABOVE
20.
21.
W4
2
K.
L.
M.
N.
O.
P.
Q.
R.
S.
6' - 2"
6' - 2"
38"
I-451
6' - 2"
F10
F10
5' - 2 1/2"
WT-4
2"
33"
2"
33"
2"
33"
2"
F10
STEEL AND GL-2
FIXTURE SURROUND,
REFER TO DETAILS
MF-5, MF-7
33"
2"
33"
2"
F10
F10
F10
WT-4
4
I-451
33"
2"
33"
2"
33"
2"
2"
INTERIOR PAINT INFORMATION
33"
F10
84"
4
I-451
2"
33"
2"
F10
STEEL AND GL-2 FIXTURE
SURROUND, REFER TO
DETAILS
MF-5, MF-7
33"
2"
33"
2"
33"
F10
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING FOR ADDITIONAL INFORMATION.
WT-4
2"
33"
2"
33"
2"
33"
2"
5
I-451
W7
NOTE 20
W9, MF-5, MF-7
4
1
I-460
RAMP
W4
> TYPE I-OP-DF DRY FALL.
FLAT.
COLORS TO BE SELECTED.
W4
FURNITURE BY OTHERS
FURNITURE BY OTHERS
> TYPE I-TR -W TRANSPARENT FINISH ON WOOD.
5
1/4" = 1'-0"
6
BOOTH SEATING 1
1/4" = 1'-0"
W.
X.
> TYPE I-OP-MD-DT MEDIUM DUTY DOOR/TRIM.
SEMI-GLOSS.
COLORS TO BE SELECTED.
> TYPE I-OP-HD HEAVY DUTY VERTICAL AND OVERHEAD
EPOXY GLOSS.
COLORS TO BE SELECTED.
EXISTING BRICK
6" STEEL FLAT STOCK FRAME
AROUND VINYL WALL MURAL.
IMAGE TO BE SELECTED BY
ARCHITECT
NOTE 20
W7
U.
V.
> TYPE I-OP ALL INTERIOR SURFACES INDICATED TO BE PAINTED.
EGGSHELL FINISH.
COLORS TO BE SELECTED.
VINYL MURAL
NEW WALL TILE BASE
T.
BOOTH SEATING 2
Y.
Z.
WALL FINISH INFORMATION
1.
2.
3.
5.
1' - 0"
>WF-1: RECLAIMED THIN WOOD
MANUFACTURER: STIKWOOD
STYLE: RECLAIMED
COLOR: MULTIPLE COLORS, TO BE SELECTED
FINISH WITH 3 COATS I-TR-W
PRODUCT MUST BE ORDERED WITH CLASS A FIRE RATED
TREATMENT OR TREATED AS SUCH ON SITE
SPECIFICATION SECTION: 06 4216 WOOD VENEER PANELING
NEW GWB, PAINTED
NOTE 1
NEW WINDOW SYSTEM BEYOND
2"
STEEL OVERHEAD STRUCTURE, PAINTED
6.
7.
8.
9.
1 1/2"
1"
1' - 0"
10.
>WF-2: "LIVE EDGE" WOOD
MANUFACTURER: MILLWORK
STYLE: TO MATCH EXISTING TREATMENT IN RETAIL SEATING AREA
COLOR: OAK VENEER OVER FIRE RATED PLYWOOD, CLEAR COAT
FINISH WITH 3 COATS I-TR-W
11.
F8
F8
F8
F8
13.
14.
F8
3' - 0"
F8
2' - 3"
6' - 8"
12.
>WF-3: VINYL WALLCOVERING
MANUFACTURER: WOLF GORDON
IMAGE AND SUBSTRATE TO BE SELECTED
15.
16.
17.
WALL TILE INFORMATION
18.
W16 AT BOOTH ENDS, TYP.
BOOTHS BY OTHERS
W16 AT BOOTH ENDS, TYP.
PAINTED 2"x2" TUBE STEEL
FRAME, GRIND ALL EDGES
SMOOTH TO TOUCH.
TOWARD PIPELINE
1/4" = 1'-0"
1"
TYP
3 5/8" 1"
7
W16 AT BOOTH ENDS, TYP.
REFER TO SPECIFICATION SECTION 09 3000 TILING
PAINTED 1"x1" TUBE STEEL
FRAME, GRIND ALL EDGES
SMOOTH TO TOUCH.
TABS WELDED TO TUBE STEEL
FRAME TO CONNECT PANEL
PAINTED MESH PANEL BOLTED TO TABS,
GRIND ALL EDGES SMOOTH TO TOUCH.
MESH PANEL TO BE SPECIFIED &
APPROVED BY ARCHITECT
CORE DRILL & SET ALL STEEL
TUBES IN EPOXY GROUT
2"
8
6"
2"
10 3/8"
1"
1' - 11 3/4"
1"
7 1/8"
>WT-1:
MANUFACTURER: SENECA BRICK
STYLE: THIN BRICK TILE
SIZE: 2 "x 8", BRICK
COLOR: GLACIER BLEND
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-2:
MANUFACTURER: FIRECLAY TILE
STYLE: KITE
SIZE: 7-1/2" x 5-1/2"
COLOR: SEVERAL COLORS TO BE SELECTED
GROUT: 1/8" GROUT JOINTS IN MAPEI OPTICOLOR OR
SIMILAR. COLOR TO BE SELECTED.
>WT-3:
MANUFACTURER: SUSAN JABLON MOSAICS
STYLE: RECYCLED
SIZE: 3/4" x 3/4"
COLOR: WHITE
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-4:
MANUFACTURER: NEMO TILE
STYLE: RAZOR
SIZE: 3/4" x 4"
COLOR: MATTE STAINLESS
GROUT: MAPEI OPTICOLOR OR SIMILAR. COLOR TO BE
SELECTED.
2"
TYPICAL STAIR HANDRAIL DETAIL
>WT-5:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: LEAD
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
1 1/2" = 1'-0"
METAL CHANNEL AND BOLT SIZES
1/4" - 20 HEX BOLT
3/16" - WASHER
4" BAR STOCK
5" BAR STOCK
}
}
}
6"+ BAR STOCK
5" & 6" CHANNEL
}
1/2" - 13 HEX BOLT
7/16" - WASHER
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
2" BAR STOCK
2" x 2" ANGLE
5/16" - 18 HEX BOLT
1/4" - WASHER
3/8" - 16 HEX BOLT
5/16" - WASHER
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
>WT-6:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: MOSS
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-7:
MANUFACTURER: FIRECLAY TILE
STYLE: PICKET
SIZE: 10-1/4" x 3-3/4"
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
>WT-8, WT-9, WT-10:
REFER TO TOILET ROOM SHEET
REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.
NEW
OF O J
S
TE
C N
RK
No.
16419
R E D A RC H
19.
20.
21.
22.
23.
24.
25.
GWB SOFFIT, REFER TO RCP FOR INFORMATION.
LINE OF CEILING, REFER TO RCP FOR INFORMATION.
HEAT LAMP TO BE HUNG CENTERED TO EQUIPMENT
BELOW, VERIFY WITH PLACEMENT OF EQUIPMENT PRIOR
TO INSTALLATION.
EXISTING SNEEZE GUARDS, REPAINT AND REPLACE
HARDWARE AS REQUIRED.
SOLID SURFACE COUNTERTOP WITH MINIMUM 2 LAYERS
OF 3/4" PLYWOOD SUBSTRATE ON ALL COUNTERS. REFER
TO SECTION FOR EDGE THICKNESS.
PROVIDE ADEQUATE BLOCKING AS REQUIRED.
SEAL & WATERPROOF ALL COUNTERTOP PENETRATIONS.
SILICONE @ ALL COUNTER TO VERTICAL SURFACE
JOINTS
PROVIDE COUNTER TOP CORE CUT OUT & GROMMET
COVER FOR ALL REQUIRED COUNTERTOP KITCHEN
EQUIPMENT POWER CORDS (TYPICAL).
PROVIDE HEAT PROOFING AT ALL HOT & COLD
EQUIPMENT WITHIN COUNTER SURFACE. REFER TO
DETAIL.
3/4" PLYWOOD DIEWALL CONSTRUCTION (NO
PARTICLEBOARD OR MDF), TYPICAL UNLESS OTHERWISE
NOTED.
UTILITY CHASE IN MILLWORK WITH REMOVABLE PANEL
FOR ACCESS.
TILE BASE, REFER TO FLOOR FINISH PLAN FOR TILE TYPE.
PROVIDE 1/4" GAP BETWEEN FLOOR FINISH AND
VERTICAL PLYWOOD CONSTRUCTION, FILL WITH
CONTINUOUS SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4" PLYWOOD SHOE
SECURED TO FLOOR (TYPICAL).
PROVIDE 4" HIGH SOLID SURFACE BACKSPLASH.
BLACK PLASTIC LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL UNLESS OTHERWISE
NOTED).
2x SOLID WOOD SHELF. SPECIES & FINISH TO BE SELECTED
BY ARCHITECT.
1/8" THICK STEEL FLAT STOCK TRIM SECURED WITH BOLT
AND WASHER DETAIL. FINISH TO BE SELECTED BY
ARCHITECT.
STEEL ANGLE CORNER GUARD SECURED WITH BOLT AND
WASHER DETAIL. FINISH TO BE SELECTED BY ARCHITECT.
POS, PROVIDED BY OTHERS.
VERTICAL STEEL TUBE SUPPORT. FINISH AS INDICATED.
PROVIDE 1/4" THICK SMOOTH MASONITE BACKER
BOARD FOR VINYL GRAPHIC.
2x2 STEEL FRAME WITH CLIPS TO HOLD BACKER BOARD,
WELDED AND GROUND CORNERS, FINISH AS INDICATED
AND SECURE TO WALL WITH Z CLIPS. PROVIDE BLOCKING
WITHIN WALL WHERE POSSIBLE.
SCRIBE ALL COUNTERS TIGHT TO FIT AND SILICONE GAPS
CLEANLY.
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
DRAWN BY:
AGK
CHECKED BY:
AGK
KEYED NOTES
4.
1/4" = 1'-0"
E
I
W14
J.
R EG
3.
I.
SEALED:
N
2.
TERMINATE WT-1 BRICK TILE WITH SCHLUTER STRIP AT THE
JOINT WHERE EXISTING TILE STOPS.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP
TO 12".
PROVIDE APPROPRIATE SCHLUTER EXTRUDED METAL TILE
EDGE DETAILS. CLEAR ALUMINUM.
EXISTING BRICK TO REMAIN - NO PAINT OR ADDITIONAL
WALL FINISH.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP CAP.
CONTINUE WT-1 TILE FROM EXISTING WALL INTO WORK
AREA. REMOVE CUT TILES AND REPLACE WITH NEW FULL
TILES AS REQUIRED TO BLEND IN PATTERN.
PROVIDE 2" STEEL ANGLE AS CORNER GUARD WITH 2" STEEL
FLAT STOCK AS BASE AND 2" STEEL FLAT STOCK @ 8'-0"
SECURED WITH BOLTS AND WASHERS TO STUDS.
EXISTING WALL TILE TO REMAIN.
WOOD PLANTER BOX TO REMAIN AND BE RECOVERED
WITH STEEL PLATE. REFER TO DETAILS.
PROVIDE FULL HEIGHT STEEL FLAT STOCK EDGE, REFER TO
DETAIL.
PROVIDE NEW GWB WALLS, PREP AND PAINT. COLOR TO
BE DETERMINED.
EXISTING WALLS, PREP AND PAINT, COLOR TO BE
DETERMINED.
PAINT WALLS ABOVE TO EXISTING CEILING.
PAINT NEW STAIR RAILING I-OP-HD. REFER TO
SPECIFICATION SECTION 09 9000 PAINTING FOR
ADDITIONAL INFORMATION. COLORS TO BE SELECTED.
NEW WALL TILE OVER EXISTING CMU WALL.
PROVIDE STEEL C-CHANNEL DETAILS AT BOOTH ENDS. WITH
IN CHANNEL WELD 2 CUSTOM HOOKS BENT FROM 8"
BOLTS. 1@30" AFF AND 1@60" AFF.
PAINT COLUMNS WITHIN STEEL FRAME AN ACCENT COLOR
TO BE SELECTED. PAINT COLUMNS ABOVE STEEL TO MATCH
CEILING COLOR.
GWB CEILING CLOUD. PAINT I-OP. COLORS TO BE
SELECTED.
EXISTING DOOR AND FRAME TO REMAIN. BUTT SCHLUTER
STRIP SNUGLY AGAINST FRAME AND PROVIDE CLEAN
GROUT EDGE.
PAINT EXISTING DOOR AND FRAME I-OP-MD-DT, COLORS
TO BE SELECTED.
PROVIDE SOLID SURFACE SILL/WALL CAP.
H.
SEY
ER OR
3' - 6 1/2"
7' - 8"
9' - 0"
5
WT-4
G.
MILLWORK FINISH INFORMATION
>MF-1: VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
COLOR: 3 COATS OF I-TR-W - COLOR TO BE SELECTED
>MF-2: PLASTIC LAMINATE
COLORS: TO BE SELECTED
>MF-3: SOLID SURFACE COUNTER TOP COLOR 1
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-4: SOLID SURFACE COUNTER TOP COLOR 2
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-5: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: PAINTED WITH CLEAR COAT SEALANT
>MF-6: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: BLACK
>MF-7: ORNAMENTAL METAL
EXPANDED METAL MESH
MANUFACTURER: BY MILLWORK SHOP
COLOR: TO BE SELECTED
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
GLAZING KEY
>GL-1:
STYLE: 1/4" FULLY TEMPERED GLASS
COLOR: CLEAR
>GL-2:
STYLE: CORRUGATED PLEXI GLASS
COLOR: OPAQUE
SHEET:
I-412
PHASE 2: ALTERATIONS & ADDITIONS
3' - 6"
E.
REFER TO SPECIFICATIONS 06 4100 ARCHITECTURAL
MILLWORK AND 05 7000 ORNAMENTAL METAL FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 12 3600 COUNTERTOPS
FOR ADDITIONAL INFORMATION.
ALL MILLWORK AND CABINETS SCOPE SHALL BE
CONSTRUCTED AND INSTALLED PER AWI CUSTOM GRADE
STANDARDS.
NO MDF OR PARTICLE BOARD SUBSTRATES WILL BE
ACCEPTABLE. 3/4" PLYWOOD ONLY.
ALL EXPOSED SURFACES SHALL BE THE FINISH AS NOTED ON
ELEVATIONS
ALL SEMI-EXPOSED SURFACES SHALL BE BLACK PLASTIC
LAMINATE.
INTERIOR FACE OF DIE WALLS TO BE FACED WITH BLACK
FRP.
SEAL ALL EXPOSED PLYWOOD EDGES AND MAINTAIN
MINIMUM 1/4" GAP FROM FLOOR TO PREVENT WICKING OF
WATER.
ALL SNEEZE GUARDS/ FOOD SHIELDS SHOWN SHOULD BE
INCLUDED WITHIN THE MILLWORK CONTRACTORS SCOPE OF
WORK.
ANY SIGNAGE & MENU FRAMES SHOULD BE INCLUDED
WITHIN THE MILLWORK'S SCOPE OF WORK
CONTRACTOR TO COORDINATE WITH EQUIPMENT
PROVIDER FOR INSTALLATION AND TESTING OF ALL
EQUIPMENT.
CONTRACTOR IS REQUIRED TO SET EQUIPMENT IN PLACE.
THIS INCLUDES, BUT IS NOT LIMITED TO, ALL OWNER SUPPLIED
"EXISTING" EQUIPMENT. CONTRACTOR TO VERIFY
EQUIPMENT DATA AS PROVIDED IN ELECTRICAL &
PLUMBING DRAWINGS TO MINIMIZE SLAB CORING
POSSIBLE. CONTRACTOR IS RESPONSIBLE FOR PLUMBING &
ELECTRICAL FEEDS TO EQUIPMENT.
PROVIDE P-LAM FACED VERTICAL APRON TO CONCEAL ALL
DROP IN EQUIPMENT AND SINKS. MOUNT ALL EQUIPMENT
CONTROLS TO CABINET FRAME AT APRON. SEE DETAILS.
COORDINATE LOCATIONS WITH EQUIPMENT.
INSIDE VERTICAL MILLWORK SURFACES ADJACENT TO
COOKING EQUIPMENT SHALL BE FINISHED w/ 20GA . TYPE
304 #4 MILL FINISH STAINLESS STEEL PANELS FASTENED TO
PLYWOOD BACKER. ALL JOINTS REQUIRE BATTEN STRIPS.
CONTRACTOR TO PROVIDE ENGINEERED SHOP DRAWINGS
INCLUDING PLAN LAYOUT DETAILS & SPECIFICATIONS FOR
ALL STRUCTURAL CONNECTIONS TO EXISTING BASE
BUILDING STRUCTURE FOR ARCHITECT'S REVIEW &
APPROVAL. ITEMS SHALL INCLUDE BUT NOT LIMITED TO WALL
BRACKET MOUNTING DETAILS, PICKPOINT CONNECTIONS
FOR SUSPENDED CEILING ELEMENTS, BEAM CLAMP,
UNISTRUT AND THREADED ROD DETAILS FOR EXHAUST
HOODS & OTHER SUSPENDED DESIGN ELEMENTS.
ALL EXPOSED BOLT & NUT CONNECTIONS ARE BOTH
FUNCTIONAL AND DECORATIVE. PAINT ALL FASTENERS TO
MATCH.
CALCULATE LOAD WEIGHT OF SUSPENDED OBJECTS TO
DETERMINE THE REQUIRED QUANTITY OF PICK POINT
LOCATIONS.
PROVIDE STAINLESS STEEL SUPPORT LEGS EVERY 4'-0" OR AS
REQUIRED TO AVOID DEFLECTION AND CRACKING OF
COUNTER SURFACE. SECURELY PIN LEG TO THE FLOOR AND
SEAL WITH SILICONE TO MAINTAIN WATERPROOFING BELOW
TILE. COORDINATE LOCATIONS SO AS NOT TO INTERFERE
WITH EQUIPMENT.
ALL EQUIPMENT MUST BE REVIEWED FOR HEIGHT SO AS NOT
TO INTERFERE WITH COUNTER HEIGHTS. ARCHITECT
RESERVES THE RIGHT TO CHANGE FOOT OR CASTER
SELECTION DURING SUBMITTAL TO KEEP HEIGHTS FORM
INTERFERING WITH COUNTERTOPS.
ALL CABINET DOOR HINGES TO BE CONTINUOUS PIANO
HINGES.
PROVIDE REINFORCEMENT TO COUNTERTOP EDGE OVER
LONG SPANS WHERE CUT OUTS FOR EQUIPMENT EXIST.
ALL STRUCTURAL HANGING ELEMENTS SHOULD BE RATED
FOR STRENGTH AND REVIEW IN SHOP DRAWINGS BY
STRUCTURAL ENGINEER.
ALL CUT OUTS FOR COUNTER TOP WELLS MUST HAVE
ROUNDED CORNERS PER MANUFACTURER'S INSTRUCTION.
CONTRACTOR TO VERIFY EQUIPMENT DATA AS PROVIDED
IN ELECTRICAL & PLUMBING DRAWINGS TO MINIMIZE SLAB
CORING, IF POSSIBLE.
PROVIDE HEAVY-DUTY REINFORCED CABINETS/ MILLWORK
STRUCTURE LOCATED UNDER BEVERAGE DISPENSER TYP.
THROUGH OUT PROJECT, PROVIDE P-LAM FACED VERTICAL
APRONS TO CONCEAL ALL DROP IN EQUIPMENT, SEE
DETAILS.
MOUNT ALL EQUIPMENT CONTROLS TO CABINET FRAME AT
APRON, SEE DETAILS.
RCNJ No. 2014-37-01C
5
I-202
A.
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
C.
D.
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL WALL
TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT ALL
WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
PAINT ALL EXPOSED CONDUIT ON WALLS. COLOR TO BE
SELECTED.
FOR SIGNAGE INFORMATION REFER TO SHEET I-460.
RAMAPO COLLEGE
OF NEW JERSEY
A.
CT
STEEL AND GL-2 FIXTURE
SURROUND, REFER TO DETAILS
B.
WT-4
WALL FINISHES
TE
NOTE 22
NOTE 22
SCOTT STUDENT CENTER
RESIDENTIAL DINING
STEEL AND GL-2
FIXTURE SURROUND,
REFER TO DETAILS
PENDANT LIGHTING
3
MA
6
I-202
PAINTED STRUCTURE ABOVE
S TAT
PAINT STRUCTURE
ABOVE, COLOR TO BE
SELECTED
PAINTED STRUCTURE ABOVE
INTERIOR ELEVATIONS
3/23/2016 6:23:49 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
3/23/2016 6:23:57 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
SEALED:
3
I
TE
No.
16419
CT
R EG
S
C N
RK
TE
MA
S TAT
E
N
I-422
SEY
ER OR
4
NEW
OF O J
R E D A RC H
I
5
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
I-422
I-422
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
7
6
I-422
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
4
RETAIL SEATING COUNTER VIEW 1
RETAIL SEATING COUNTER VIEW 2
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
I-451
7
9
I-421
'
10
-6
"
1'
-6
2
3
I-450
I-450
"
8
STOREFRONT WINDOW SYSTEM
1
1'
I-450
-6
"
6
2
1' - 6"
1/2" SOLID SURFACE ON (2)
LAYERS OF 3/4" PLYWOOD
I-420
2"
I-421
3 4
I-450
1
0'
6"
2"x2" PAINTED STEEL ANGLE (GRIND ALL
EDGES SMOOTH TO TOUCH) WELDED
CONNECTION TO VERTICAL CHANNELS.
1 5/8"
F
1"
4
I-421
8'
2
6"
5"
2' - 8"
1
1 5/8"
8 3/4"
6"
5
"
4" PAINTED STEEL CHANNEL (GRIND ALL
EDGES SMOOTH TO TOUCH) WELDED
TO PAINTED STEEL BASE PLATE &
MOUNTED TO FLOOR w/ (4)
EXPANSION BOLT SET IN EPOXY GROUT.
1'
-0
"
2"x2" PAINTED STEEL ANGLE (GRIND ALL
EDGES SMOOTH TO TOUCH) WELDED
CONNECTION TO VERTICAL CHANNELS.
FIN TUBE HEATING, REFER TO
MECHANICAL DRAWINGS.
8"
8
6
'-
EXISTING CARPET & CONCRETE
SLAB TO REMAIN
MAIN LEVEL
0' - 0"
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
1
RETAIL SEATING AREA PLAN
3/16" = 1'-0"
2
RETAIL DINING WINDOW COUNTERTOP
1 1/2" = 1'-0"
SHEET:
I-420
PHASE 2: ALTERATIONS & ADDITIONS
"
RCNJ No. 2014-37-01C
I-452
-6
AGK/JNC
RAMAPO COLLEGE
OF NEW JERSEY
1
8'
CHECKED BY:
SCOTT STUDENT CENTER
RESIDENTIAL DINING
6"
6"
2
AGK/JNC
RETAIL SEATING AREA PLAN
8'
DRAWN BY:
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
1
I-422
3' - 6"
3
6"+ BAR STOCK
5" & 6" CHANNEL
}
3/8" - 16 HEX BOLT
5/16" - WASHER
1/2" - 13 HEX BOLT
7/16" - WASHER
B.
C.
D.
E.
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
F.
G.
GENERAL NOTES
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL WALL
TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT ALL
WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
PAINT ALL EXPOSED CONDUIT ON WALLS. COLOR TO BE
SELECTED.
FOR SIGNAGE INFORMATION REFER TO SHEET I-460.
A.
B.
C.
D.
E.
F.
WALL FINISH KEYED NOTES
REFER TO WALL FINISH PLAN.
THE PREFIX "W" INDICATES WALL FINISH NOTE.
1.
WALL BASE
W4
NEW STAIR AND METAL RAIL
W14
3.
NEW CONCRETE STAIR
FINISH AS SPECIFIED
4.
5.
6.
1
2
LOWER LOUNGE 1
3
LOWER LOUNGE 2
LOWER LOUNGE DINING FEATURE WALL
7.
1/4" = 1'-0"
1/4" = 1'-0"
1/4" = 1'-0"
8.
9.
GWB SOFFIT BEYOND, PAINTED
2
3
I-450
I-450
MF-2
MF-5, MF-7
W4
OVERHEAD CLOUD
STRUCTURE, REFER TO RCP
10.
MF-5, MF-7
11.
12.
PAINT NEW GWB WALL
13.
14.
15.
16.
W7, MF-5
F11
F11
F11
F11
F11
F11
1
WT-4 ON
EXISTING
COLUMN
I-450
17.
MF-5, W9
MF-5, W9
18.
19.
W4
NEW STAIR AND METAL RAIL
NEW GLASS INFILL
WALL BASE
W4
NEW GAS FIRE PLACE
FROM SUPERIOR
FIREPLACES
AGES SILVER FINISH WITH
AMBER GLASS ROCKS
VRL4543
NEW WINDOW SYSTEM BEYOND
W14
MF-5
WALL BASE
20.
21.
INTERIOR PAINT INFORMATION
4
5
LOWER LOUNGE 3
1/4" = 1'-0"
6
LOWER LOUNGE BOOTH
1/4" = 1'-0"
5' - 6 1/2"
1
I-452
OVERHEAD
CLOUD
STRUCTURE,
REFER TO RCP
MF-2
5' - 6 1/2"
3' - 4 1/2"
2
I-451
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING FOR ADDITIONAL INFORMATION.
1/4" = 1'-0"
> TYPE I-OP ALL INTERIOR SURFACES INDICATED TO BE PAINTED.
EGGSHELL FINISH.
COLORS TO BE SELECTED.
I-450
I-450
> TYPE I-OP-MD-DT MEDIUM DUTY DOOR/TRIM.
SEMI-GLOSS.
COLORS TO BE SELECTED.
PAINT STRUCTURE ABOVE
OVERHEAD STRUCTURE, REFER TO RCP
6' - 2"
6' - 2"
PAINT STRUCTURE ABOVE
PAINT STRUCTURE ABOVE
W13
W13
11 1/2"
1
MF-5, MF-7
2"
I-450
MF-5, W9
W11
MF-5, W9
2' - 8"
SOLID SURFACE
MILLWORK
4' - 4"
W21
W11
WALL BASE
NOTE 20
8
UPPER LOUNGE 1
1/4" = 1'-0"
W11
N.
O.
P.
Q.
R.
S.
T.
U.
W.
W4
MF-5, MF-7
EXISTING BRICK LOW WALL
> TYPE I-TR -W TRANSPARENT FINISH ON WOOD.
Y.
Z.
WALL FINISH INFORMATION
>WF-1: RECLAIMED THIN WOOD
MANUFACTURER: STIKWOOD
STYLE: RECLAIMED
COLOR: MULTIPLE COLORS, TO BE SELECTED
FINISH WITH 3 COATS I-TR-W
PRODUCT MUST BE ORDERED WITH CLASS A FIRE RATED
TREATMENT OR TREATED AS SUCH ON SITE
SPECIFICATION SECTION: 06 4216 WOOD VENEER PANELING
1.
2.
3.
5.
6.
7.
8.
9.
10.
9
UPPER LOUNGE 3
1/4" = 1'-0"
UPPER LOUNGE 4
>WF-2: "LIVE EDGE" WOOD
MANUFACTURER: MILLWORK
STYLE: TO MATCH EXISTING TREATMENT IN RETAIL SEATING AREA
COLOR: OAK VENEER OVER FIRE RATED PLYWOOD, CLEAR COAT
FINISH WITH 3 COATS I-TR-W
11.
12.
1/4" = 1'-0"
>WF-3: VINYL WALLCOVERING
MANUFACTURER: WOLF GORDON
IMAGE AND SUBSTRATE TO BE SELECTED
13.
14.
15.
16.
17.
WALL TILE INFORMATION
18.
REFER TO SPECIFICATION SECTION 09 3000 TILING
>WT-1:
MANUFACTURER: SENECA BRICK
STYLE: THIN BRICK TILE
SIZE: 2 "x 8", BRICK
COLOR: GLACIER BLEND
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-2:
MANUFACTURER: FIRECLAY TILE
STYLE: KITE
SIZE: 7-1/2" x 5-1/2"
COLOR: SEVERAL COLORS TO BE SELECTED
GROUT: 1/8" GROUT JOINTS IN MAPEI OPTICOLOR OR
SIMILAR. COLOR TO BE SELECTED.
10
LOWER LOUNGE
11
LOWER LOUNGE 2
12
13
UPPER LOUNGE 1
UPPER LOUNGE 2
>WT-3:
MANUFACTURER: SUSAN JABLON MOSAICS
STYLE: RECYCLED
SIZE: 3/4" x 3/4"
COLOR: WHITE
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-4:
MANUFACTURER: NEMO TILE
STYLE: RAZOR
SIZE: 3/4" x 4"
COLOR: MATTE STAINLESS
GROUT: MAPEI OPTICOLOR OR SIMILAR. COLOR TO BE
SELECTED.
>WT-5:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: LEAD
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-6:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: MOSS
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-7:
MANUFACTURER: FIRECLAY TILE
STYLE: PICKET
SIZE: 10-1/4" x 3-3/4"
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
14
UPPER LOUNGE 3
15
UPPER LOUNGE 4
16
>WT-8, WT-9, WT-10:
REFER TO TOILET ROOM SHEET
UPPER LOUNGE 5
REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.
NEW
OF O J
S
TE
C N
RK
No.
16419
R E D A RC H
19.
20.
21.
22.
23.
24.
25.
GWB SOFFIT, REFER TO RCP FOR INFORMATION.
LINE OF CEILING, REFER TO RCP FOR INFORMATION.
HEAT LAMP TO BE HUNG CENTERED TO EQUIPMENT
BELOW, VERIFY WITH PLACEMENT OF EQUIPMENT PRIOR
TO INSTALLATION.
EXISTING SNEEZE GUARDS, REPAINT AND REPLACE
HARDWARE AS REQUIRED.
SOLID SURFACE COUNTERTOP WITH MINIMUM 2 LAYERS
OF 3/4" PLYWOOD SUBSTRATE ON ALL COUNTERS. REFER
TO SECTION FOR EDGE THICKNESS.
PROVIDE ADEQUATE BLOCKING AS REQUIRED.
SEAL & WATERPROOF ALL COUNTERTOP PENETRATIONS.
SILICONE @ ALL COUNTER TO VERTICAL SURFACE
JOINTS
PROVIDE COUNTER TOP CORE CUT OUT & GROMMET
COVER FOR ALL REQUIRED COUNTERTOP KITCHEN
EQUIPMENT POWER CORDS (TYPICAL).
PROVIDE HEAT PROOFING AT ALL HOT & COLD
EQUIPMENT WITHIN COUNTER SURFACE. REFER TO
DETAIL.
3/4" PLYWOOD DIEWALL CONSTRUCTION (NO
PARTICLEBOARD OR MDF), TYPICAL UNLESS OTHERWISE
NOTED.
UTILITY CHASE IN MILLWORK WITH REMOVABLE PANEL
FOR ACCESS.
TILE BASE, REFER TO FLOOR FINISH PLAN FOR TILE TYPE.
PROVIDE 1/4" GAP BETWEEN FLOOR FINISH AND
VERTICAL PLYWOOD CONSTRUCTION, FILL WITH
CONTINUOUS SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4" PLYWOOD SHOE
SECURED TO FLOOR (TYPICAL).
PROVIDE 4" HIGH SOLID SURFACE BACKSPLASH.
BLACK PLASTIC LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL UNLESS OTHERWISE
NOTED).
2x SOLID WOOD SHELF. SPECIES & FINISH TO BE SELECTED
BY ARCHITECT.
1/8" THICK STEEL FLAT STOCK TRIM SECURED WITH BOLT
AND WASHER DETAIL. FINISH TO BE SELECTED BY
ARCHITECT.
STEEL ANGLE CORNER GUARD SECURED WITH BOLT AND
WASHER DETAIL. FINISH TO BE SELECTED BY ARCHITECT.
POS, PROVIDED BY OTHERS.
VERTICAL STEEL TUBE SUPPORT. FINISH AS INDICATED.
PROVIDE 1/4" THICK SMOOTH MASONITE BACKER
BOARD FOR VINYL GRAPHIC.
2x2 STEEL FRAME WITH CLIPS TO HOLD BACKER BOARD,
WELDED AND GROUND CORNERS, FINISH AS INDICATED
AND SECURE TO WALL WITH Z CLIPS. PROVIDE BLOCKING
WITHIN WALL WHERE POSSIBLE.
SCRIBE ALL COUNTERS TIGHT TO FIT AND SILICONE GAPS
CLEANLY.
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
DRAWN BY:
AGK
CHECKED BY:
AGK
KEYED NOTES
4.
MF-5, W9
NEW GAS FIRE PLACE
FROM SUPERIOR
FIREPLACES
AGES SILVER FINISH WITH
AMBER GLASS ROCKS
VRL4543
MF-5
7
1
I-450
W4
W4
WALL BASE
9' - 0"
5' - 2 1/2"
5"
W21
MF-5, MF-7
5' - 2 1/2"
WT-4
MF-5, MF-7
> TYPE I-OP-HD HEAVY DUTY VERTICAL AND OVERHEAD
EPOXY GLOSS.
COLORS TO BE SELECTED.
> TYPE I-OP-DF DRY FALL.
FLAT.
COLORS TO BE SELECTED.
1 3/4"
5' - 9"
11 1/2"
W13
MF-5, MF-7
M.
X.
2
MF-2
L.
V.
3' - 4 1/2"
3
OVERHEAD CLOUD
STRUCTURE, REFER TO
RCP
LOWER LOUNGE FIRE PLACE
K.
E
I
NEW METAL
HANDRAILS, W14
MF-5
J.
R EG
PAINT DOOR FRAME
MF-5
I.
SEALED:
N
2.
H.
SEY
ER OR
106
TERMINATE WT-1 BRICK TILE WITH SCHLUTER STRIP AT THE
JOINT WHERE EXISTING TILE STOPS.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP
TO 12".
PROVIDE APPROPRIATE SCHLUTER EXTRUDED METAL TILE
EDGE DETAILS. CLEAR ALUMINUM.
EXISTING BRICK TO REMAIN - NO PAINT OR ADDITIONAL
WALL FINISH.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP CAP.
CONTINUE WT-1 TILE FROM EXISTING WALL INTO WORK
AREA. REMOVE CUT TILES AND REPLACE WITH NEW FULL
TILES AS REQUIRED TO BLEND IN PATTERN.
PROVIDE 2" STEEL ANGLE AS CORNER GUARD WITH 2" STEEL
FLAT STOCK AS BASE AND 2" STEEL FLAT STOCK @ 8'-0"
SECURED WITH BOLTS AND WASHERS TO STUDS.
EXISTING WALL TILE TO REMAIN.
WOOD PLANTER BOX TO REMAIN AND BE RECOVERED
WITH STEEL PLATE. REFER TO DETAILS.
PROVIDE FULL HEIGHT STEEL FLAT STOCK EDGE, REFER TO
DETAIL.
PROVIDE NEW GWB WALLS, PREP AND PAINT. COLOR TO
BE DETERMINED.
EXISTING WALLS, PREP AND PAINT, COLOR TO BE
DETERMINED.
PAINT WALLS ABOVE TO EXISTING CEILING.
PAINT NEW STAIR RAILING I-OP-HD. REFER TO
SPECIFICATION SECTION 09 9000 PAINTING FOR
ADDITIONAL INFORMATION. COLORS TO BE SELECTED.
NEW WALL TILE OVER EXISTING CMU WALL.
PROVIDE STEEL C-CHANNEL DETAILS AT BOOTH ENDS. WITH
IN CHANNEL WELD 2 CUSTOM HOOKS BENT FROM 8"
BOLTS. 1@30" AFF AND 1@60" AFF.
PAINT COLUMNS WITHIN STEEL FRAME AN ACCENT COLOR
TO BE SELECTED. PAINT COLUMNS ABOVE STEEL TO MATCH
CEILING COLOR.
GWB CEILING CLOUD. PAINT I-OP. COLORS TO BE
SELECTED.
EXISTING DOOR AND FRAME TO REMAIN. BUTT SCHLUTER
STRIP SNUGLY AGAINST FRAME AND PROVIDE CLEAN
GROUT EDGE.
PAINT EXISTING DOOR AND FRAME I-OP-MD-DT, COLORS
TO BE SELECTED.
PROVIDE SOLID SURFACE SILL/WALL CAP.
G.
REFER TO SPECIFICATIONS 06 4100 ARCHITECTURAL
MILLWORK AND 05 7000 ORNAMENTAL METAL FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 12 3600 COUNTERTOPS
FOR ADDITIONAL INFORMATION.
ALL MILLWORK AND CABINETS SCOPE SHALL BE
CONSTRUCTED AND INSTALLED PER AWI CUSTOM GRADE
STANDARDS.
NO MDF OR PARTICLE BOARD SUBSTRATES WILL BE
ACCEPTABLE. 3/4" PLYWOOD ONLY.
ALL EXPOSED SURFACES SHALL BE THE FINISH AS NOTED ON
ELEVATIONS
ALL SEMI-EXPOSED SURFACES SHALL BE BLACK PLASTIC
LAMINATE.
INTERIOR FACE OF DIE WALLS TO BE FACED WITH BLACK
FRP.
SEAL ALL EXPOSED PLYWOOD EDGES AND MAINTAIN
MINIMUM 1/4" GAP FROM FLOOR TO PREVENT WICKING OF
WATER.
ALL SNEEZE GUARDS/ FOOD SHIELDS SHOWN SHOULD BE
INCLUDED WITHIN THE MILLWORK CONTRACTORS SCOPE OF
WORK.
ANY SIGNAGE & MENU FRAMES SHOULD BE INCLUDED
WITHIN THE MILLWORK'S SCOPE OF WORK
CONTRACTOR TO COORDINATE WITH EQUIPMENT
PROVIDER FOR INSTALLATION AND TESTING OF ALL
EQUIPMENT.
CONTRACTOR IS REQUIRED TO SET EQUIPMENT IN PLACE.
THIS INCLUDES, BUT IS NOT LIMITED TO, ALL OWNER SUPPLIED
"EXISTING" EQUIPMENT. CONTRACTOR TO VERIFY
EQUIPMENT DATA AS PROVIDED IN ELECTRICAL &
PLUMBING DRAWINGS TO MINIMIZE SLAB CORING
POSSIBLE. CONTRACTOR IS RESPONSIBLE FOR PLUMBING &
ELECTRICAL FEEDS TO EQUIPMENT.
PROVIDE P-LAM FACED VERTICAL APRON TO CONCEAL ALL
DROP IN EQUIPMENT AND SINKS. MOUNT ALL EQUIPMENT
CONTROLS TO CABINET FRAME AT APRON. SEE DETAILS.
COORDINATE LOCATIONS WITH EQUIPMENT.
INSIDE VERTICAL MILLWORK SURFACES ADJACENT TO
COOKING EQUIPMENT SHALL BE FINISHED w/ 20GA . TYPE
304 #4 MILL FINISH STAINLESS STEEL PANELS FASTENED TO
PLYWOOD BACKER. ALL JOINTS REQUIRE BATTEN STRIPS.
CONTRACTOR TO PROVIDE ENGINEERED SHOP DRAWINGS
INCLUDING PLAN LAYOUT DETAILS & SPECIFICATIONS FOR
ALL STRUCTURAL CONNECTIONS TO EXISTING BASE
BUILDING STRUCTURE FOR ARCHITECT'S REVIEW &
APPROVAL. ITEMS SHALL INCLUDE BUT NOT LIMITED TO WALL
BRACKET MOUNTING DETAILS, PICKPOINT CONNECTIONS
FOR SUSPENDED CEILING ELEMENTS, BEAM CLAMP,
UNISTRUT AND THREADED ROD DETAILS FOR EXHAUST
HOODS & OTHER SUSPENDED DESIGN ELEMENTS.
ALL EXPOSED BOLT & NUT CONNECTIONS ARE BOTH
FUNCTIONAL AND DECORATIVE. PAINT ALL FASTENERS TO
MATCH.
CALCULATE LOAD WEIGHT OF SUSPENDED OBJECTS TO
DETERMINE THE REQUIRED QUANTITY OF PICK POINT
LOCATIONS.
PROVIDE STAINLESS STEEL SUPPORT LEGS EVERY 4'-0" OR AS
REQUIRED TO AVOID DEFLECTION AND CRACKING OF
COUNTER SURFACE. SECURELY PIN LEG TO THE FLOOR AND
SEAL WITH SILICONE TO MAINTAIN WATERPROOFING BELOW
TILE. COORDINATE LOCATIONS SO AS NOT TO INTERFERE
WITH EQUIPMENT.
ALL EQUIPMENT MUST BE REVIEWED FOR HEIGHT SO AS NOT
TO INTERFERE WITH COUNTER HEIGHTS. ARCHITECT
RESERVES THE RIGHT TO CHANGE FOOT OR CASTER
SELECTION DURING SUBMITTAL TO KEEP HEIGHTS FORM
INTERFERING WITH COUNTERTOPS.
ALL CABINET DOOR HINGES TO BE CONTINUOUS PIANO
HINGES.
PROVIDE REINFORCEMENT TO COUNTERTOP EDGE OVER
LONG SPANS WHERE CUT OUTS FOR EQUIPMENT EXIST.
ALL STRUCTURAL HANGING ELEMENTS SHOULD BE RATED
FOR STRENGTH AND REVIEW IN SHOP DRAWINGS BY
STRUCTURAL ENGINEER.
ALL CUT OUTS FOR COUNTER TOP WELLS MUST HAVE
ROUNDED CORNERS PER MANUFACTURER'S INSTRUCTION.
CONTRACTOR TO VERIFY EQUIPMENT DATA AS PROVIDED
IN ELECTRICAL & PLUMBING DRAWINGS TO MINIMIZE SLAB
CORING, IF POSSIBLE.
PROVIDE HEAVY-DUTY REINFORCED CABINETS/ MILLWORK
STRUCTURE LOCATED UNDER BEVERAGE DISPENSER TYP.
THROUGH OUT PROJECT, PROVIDE P-LAM FACED VERTICAL
APRONS TO CONCEAL ALL DROP IN EQUIPMENT, SEE
DETAILS.
MOUNT ALL EQUIPMENT CONTROLS TO CABINET FRAME AT
APRON, SEE DETAILS.
MILLWORK FINISH INFORMATION
>MF-1: VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
COLOR: 3 COATS OF I-TR-W - COLOR TO BE SELECTED
>MF-2: PLASTIC LAMINATE
COLORS: TO BE SELECTED
>MF-3: SOLID SURFACE COUNTER TOP COLOR 1
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-4: SOLID SURFACE COUNTER TOP COLOR 2
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-5: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: PAINTED WITH CLEAR COAT SEALANT
>MF-6: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: BLACK
>MF-7: ORNAMENTAL METAL
EXPANDED METAL MESH
MANUFACTURER: BY MILLWORK SHOP
COLOR: TO BE SELECTED
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
GLAZING KEY
>GL-1:
STYLE: 1/4" FULLY TEMPERED GLASS
COLOR: CLEAR
>GL-2:
STYLE: CORRUGATED PLEXI GLASS
COLOR: OPAQUE
SHEET:
I-421
PHASE 2: ALTERATIONS & ADDITIONS
4" BAR STOCK
5" BAR STOCK
A.
GENERAL NOTES
RCNJ No. 2014-37-01C
WF-2
5/16" - 18 HEX BOLT
1/4" - WASHER
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
2" BAR STOCK
2" x 2" ANGLE
INTERIOR|ELEVATIONS
RAMAPO COLLEGE
OF NEW JERSEY
CEILING CLOUD
ABOVE, REFER TO RCP
WALL FINISHES
CT
MF-5
I-450
1/4" - 20 HEX BOLT
3/16" - WASHER
TE
WF-2
I-450
}
}
}
SCOTT STUDENT CENTER
RESIDENTIAL DINING
MF-5
4
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
4
EXISTING OPENING,
REPLACE CASING
MA
PAINT NEW GWB
OVERHEAD CEILING
CLOUD, REFER TO RCP
S TAT
METAL CHANNEL AND BOLT SIZES
INTERIOR ELEVATIONS
3/23/2016 6:25:12 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
E.
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
F.
G.
B.
C.
D.
E.
F.
WALL FINISH KEYED NOTES
FRAME IN 3" STEEL FLAT STOCK WITH
BOLT AND WASHER DETAIL
REFER TO WALL FINISH PLAN.
THE PREFIX "W" INDICATES WALL FINISH NOTE.
WF-1
FIN TUBE, REFER TO
MECHANICAL DRAWINGS
1.
3.
EXISTING BRICK, PAINTED
5.
6.
4" C-CHANNEL
CONNECTED TO WALL
WITH 1/4" PLATE FINISHED
AS SPECIFIED
7.
8.
9.
10.
11.
WF-1
WT-1
VENEERED WOOD CEILING TREATMENT TO MATCH EXISTING
VENEERED WOOD CEILING TREATMENT TO MATCH EXISTING
12.
13.
14.
1
2
ATRUIUM ADDITION
ENTRY VESTIBULE
1/4" = 1'-0"
15.
16.
17.
18.
19.
WT-5
WT-5
WT-5
WT-6
WT-6
WT-6
WT-5
WT-5
WT-5
WT-6
WT-6
WT-6
WT-5
WT-5
WT-5
WT-6
WT-6
WT-6
WT-5
WT-5
WT-5
WT-6
WT-6
WT-6
WT-5
WT-5
109
110
20.
21.
INTERIOR PAINT INFORMATION
REFER TO SPECIFICATION SECTION 09 9000 PAINTING AND
COATING FOR ADDITIONAL INFORMATION.
108
NEW DRINKING FOUNTAIN
PAINT DOORS AND FRAMES I-OP-MD-DT
NEW STOREFRONT WINDOW SYSTEM
3
4
NEW VESTIBULE 1
5
NEW VESTIBULE 4
1/4" = 1'-0"
TOWARDS TOILET ROOMS
1/4" = 1'-0"
1/4" = 1'-0"
> TYPE I-OP ALL INTERIOR SURFACES INDICATED TO BE PAINTED.
EGGSHELL FINISH.
COLORS TO BE SELECTED.
> TYPE I-OP-HD HEAVY DUTY VERTICAL AND OVERHEAD
EPOXY GLOSS.
COLORS TO BE SELECTED.
> TYPE I-OP-DF DRY FALL.
FLAT.
COLORS TO BE SELECTED.
C-CHANNEL AND WOOD PLANK CEILING
PAINT OVERHEAD STRUCTURE
W7, MF-5
WF-1
WRAP CORNER WITH TILE,
USE SCHLUTER CORNER
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
W.
X.
> TYPE I-OP-MD-DT MEDIUM DUTY DOOR/TRIM.
SEMI-GLOSS.
COLORS TO BE SELECTED.
> TYPE I-TR -W TRANSPARENT FINISH ON WOOD.
W10, MF-5
K.
V.
WT-5
PAINT DOOR AND FRAMES I-OP-MD-DT
J.
Y.
Z.
WALL FINISH INFORMATION
WOOD CEILING AND
C-CHANNEL CLOUD
>WF-1: RECLAIMED THIN WOOD
MANUFACTURER: STIKWOOD
STYLE: RECLAIMED
COLOR: MULTIPLE COLORS, TO BE SELECTED
FINISH WITH 3 COATS I-TR-W
PRODUCT MUST BE ORDERED WITH CLASS A FIRE RATED
TREATMENT OR TREATED AS SUCH ON SITE
SPECIFICATION SECTION: 06 4216 WOOD VENEER PANELING
W10, MF-5
WF-1
WRAP CORNER WITH TILE,
USE SCHLUTER CORNER
WT-6
WT-5
1.
2.
3.
5.
6.
7.
8.
9.
10.
WT-6
>WF-2: "LIVE EDGE" WOOD
MANUFACTURER: MILLWORK
STYLE: TO MATCH EXISTING TREATMENT IN RETAIL SEATING AREA
COLOR: OAK VENEER OVER FIRE RATED PLYWOOD, CLEAR COAT
FINISH WITH 3 COATS I-TR-W
WT-5
WT-6
WT-5
11.
12.
>WF-3: VINYL WALLCOVERING
MANUFACTURER: WOLF GORDON
IMAGE AND SUBSTRATE TO BE SELECTED
WT-6
WT-5
13.
14.
PAINT STEEL COLUMNS I-OP-HD
NEW ATM ENCLOSURE CONSTRUCTED FROM
STUD AND GWB WITH WF-1 FINISH AND
EDGES IN CLEAR COATED STEEL WITH BOLT
AND WASHER DETAILS
WT-1
NEW ATM ENCLOSURE CONSTRUCTED
FROM STUD AND GWB WITH WF-1 FINISH
AND EDGES IN CLEAR COATED STEEL WITH
BOLT AND WASHER DETAILS
15.
16.
17.
CONFIRM DIMENSIONS WITH ATM ON SITE
WALL TILE INFORMATION
18.
REFER TO SPECIFICATION SECTION 09 3000 TILING
6
7
ATRIUM ADDITION 2
1/4" = 1'-0"
8
ATM ENCLOSURE
ATM SURROUND
1/4" = 1'-0"
>WT-1:
MANUFACTURER: SENECA BRICK
STYLE: THIN BRICK TILE
SIZE: 2 "x 8", BRICK
COLOR: GLACIER BLEND
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-2:
MANUFACTURER: FIRECLAY TILE
STYLE: KITE
SIZE: 7-1/2" x 5-1/2"
COLOR: SEVERAL COLORS TO BE SELECTED
GROUT: 1/8" GROUT JOINTS IN MAPEI OPTICOLOR OR
SIMILAR. COLOR TO BE SELECTED.
>WT-3:
MANUFACTURER: SUSAN JABLON MOSAICS
STYLE: RECYCLED
SIZE: 3/4" x 3/4"
COLOR: WHITE
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-4:
MANUFACTURER: NEMO TILE
STYLE: RAZOR
SIZE: 3/4" x 4"
COLOR: MATTE STAINLESS
GROUT: MAPEI OPTICOLOR OR SIMILAR. COLOR TO BE
SELECTED.
>WT-5:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: LEAD
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-6:
MANUFACTURER: CROSSVILLE TILE
STYLE: NOW
SIZE: 3" x 12"
COLOR: MOSS
GROUT: MAPEI OPTICOLOR OR SIMILAR. CHARCOAL.
>WT-7:
MANUFACTURER: FIRECLAY TILE
STYLE: PICKET
SIZE: 10-1/4" x 3-3/4"
COLOR: TO BE SELECTED
GROUT: MAPEI OPTICOLOR OR SIMILAR.
9
ATM
10
BAR SEATING
11
ENTRY VESTIBULE 2
>WT-8, WT-9, WT-10:
REFER TO TOILET ROOM SHEET
REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.
NEW
OF O J
S
TE
C N
RK
No.
16419
R E D A RC H
19.
20.
21.
22.
23.
24.
25.
GWB SOFFIT, REFER TO RCP FOR INFORMATION.
LINE OF CEILING, REFER TO RCP FOR INFORMATION.
HEAT LAMP TO BE HUNG CENTERED TO EQUIPMENT
BELOW, VERIFY WITH PLACEMENT OF EQUIPMENT PRIOR
TO INSTALLATION.
EXISTING SNEEZE GUARDS, REPAINT AND REPLACE
HARDWARE AS REQUIRED.
SOLID SURFACE COUNTERTOP WITH MINIMUM 2 LAYERS
OF 3/4" PLYWOOD SUBSTRATE ON ALL COUNTERS. REFER
TO SECTION FOR EDGE THICKNESS.
PROVIDE ADEQUATE BLOCKING AS REQUIRED.
SEAL & WATERPROOF ALL COUNTERTOP PENETRATIONS.
SILICONE @ ALL COUNTER TO VERTICAL SURFACE
JOINTS
PROVIDE COUNTER TOP CORE CUT OUT & GROMMET
COVER FOR ALL REQUIRED COUNTERTOP KITCHEN
EQUIPMENT POWER CORDS (TYPICAL).
PROVIDE HEAT PROOFING AT ALL HOT & COLD
EQUIPMENT WITHIN COUNTER SURFACE. REFER TO
DETAIL.
3/4" PLYWOOD DIEWALL CONSTRUCTION (NO
PARTICLEBOARD OR MDF), TYPICAL UNLESS OTHERWISE
NOTED.
UTILITY CHASE IN MILLWORK WITH REMOVABLE PANEL
FOR ACCESS.
TILE BASE, REFER TO FLOOR FINISH PLAN FOR TILE TYPE.
PROVIDE 1/4" GAP BETWEEN FLOOR FINISH AND
VERTICAL PLYWOOD CONSTRUCTION, FILL WITH
CONTINUOUS SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4" PLYWOOD SHOE
SECURED TO FLOOR (TYPICAL).
PROVIDE 4" HIGH SOLID SURFACE BACKSPLASH.
BLACK PLASTIC LAMINATE ON ALL EXPOSED INTERIOR
MILLWORK SURFACES (TYPICAL UNLESS OTHERWISE
NOTED).
2x SOLID WOOD SHELF. SPECIES & FINISH TO BE SELECTED
BY ARCHITECT.
1/8" THICK STEEL FLAT STOCK TRIM SECURED WITH BOLT
AND WASHER DETAIL. FINISH TO BE SELECTED BY
ARCHITECT.
STEEL ANGLE CORNER GUARD SECURED WITH BOLT AND
WASHER DETAIL. FINISH TO BE SELECTED BY ARCHITECT.
POS, PROVIDED BY OTHERS.
VERTICAL STEEL TUBE SUPPORT. FINISH AS INDICATED.
PROVIDE 1/4" THICK SMOOTH MASONITE BACKER
BOARD FOR VINYL GRAPHIC.
2x2 STEEL FRAME WITH CLIPS TO HOLD BACKER BOARD,
WELDED AND GROUND CORNERS, FINISH AS INDICATED
AND SECURE TO WALL WITH Z CLIPS. PROVIDE BLOCKING
WITHIN WALL WHERE POSSIBLE.
SCRIBE ALL COUNTERS TIGHT TO FIT AND SILICONE GAPS
CLEANLY.
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
DRAWN BY:
AGK
CHECKED BY:
AGK
KEYED NOTES
4.
W13
E
I
4.
I.
SEALED:
N
4" C-CHANNEL
H.
SEY
ER OR
2.
EXISTING STEEL BEAM,
CLEANED AND PAINTED
TERMINATE WT-1 BRICK TILE WITH SCHLUTER STRIP AT THE
JOINT WHERE EXISTING TILE STOPS.
PROVIDE WATERPROOFING BEHIND WALL FINISH. WRAP
WATERPROOFING MEMBRANE FROM FLOOR TO WALL UP
TO 12".
PROVIDE APPROPRIATE SCHLUTER EXTRUDED METAL TILE
EDGE DETAILS. CLEAR ALUMINUM.
EXISTING BRICK TO REMAIN - NO PAINT OR ADDITIONAL
WALL FINISH.
TERMINATE ALL WALL TILE WITH SCHLUTER METAL TOP CAP.
CONTINUE WT-1 TILE FROM EXISTING WALL INTO WORK
AREA. REMOVE CUT TILES AND REPLACE WITH NEW FULL
TILES AS REQUIRED TO BLEND IN PATTERN.
PROVIDE 2" STEEL ANGLE AS CORNER GUARD WITH 2" STEEL
FLAT STOCK AS BASE AND 2" STEEL FLAT STOCK @ 8'-0"
SECURED WITH BOLTS AND WASHERS TO STUDS.
EXISTING WALL TILE TO REMAIN.
WOOD PLANTER BOX TO REMAIN AND BE RECOVERED
WITH STEEL PLATE. REFER TO DETAILS.
PROVIDE FULL HEIGHT STEEL FLAT STOCK EDGE, REFER TO
DETAIL.
PROVIDE NEW GWB WALLS, PREP AND PAINT. COLOR TO
BE DETERMINED.
EXISTING WALLS, PREP AND PAINT, COLOR TO BE
DETERMINED.
PAINT WALLS ABOVE TO EXISTING CEILING.
PAINT NEW STAIR RAILING I-OP-HD. REFER TO
SPECIFICATION SECTION 09 9000 PAINTING FOR
ADDITIONAL INFORMATION. COLORS TO BE SELECTED.
NEW WALL TILE OVER EXISTING CMU WALL.
PROVIDE STEEL C-CHANNEL DETAILS AT BOOTH ENDS. WITH
IN CHANNEL WELD 2 CUSTOM HOOKS BENT FROM 8"
BOLTS. 1@30" AFF AND 1@60" AFF.
PAINT COLUMNS WITHIN STEEL FRAME AN ACCENT COLOR
TO BE SELECTED. PAINT COLUMNS ABOVE STEEL TO MATCH
CEILING COLOR.
GWB CEILING CLOUD. PAINT I-OP. COLORS TO BE
SELECTED.
EXISTING DOOR AND FRAME TO REMAIN. BUTT SCHLUTER
STRIP SNUGLY AGAINST FRAME AND PROVIDE CLEAN
GROUT EDGE.
PAINT EXISTING DOOR AND FRAME I-OP-MD-DT, COLORS
TO BE SELECTED.
PROVIDE SOLID SURFACE SILL/WALL CAP.
G.
R EG
REFER TO SPECIFICATIONS 06 4100 ARCHITECTURAL
MILLWORK AND 05 7000 ORNAMENTAL METAL FOR
ADDITIONAL INFORMATION.
REFER TO SPECIFICATION SECTION 12 3600 COUNTERTOPS
FOR ADDITIONAL INFORMATION.
ALL MILLWORK AND CABINETS SCOPE SHALL BE
CONSTRUCTED AND INSTALLED PER AWI CUSTOM GRADE
STANDARDS.
NO MDF OR PARTICLE BOARD SUBSTRATES WILL BE
ACCEPTABLE. 3/4" PLYWOOD ONLY.
ALL EXPOSED SURFACES SHALL BE THE FINISH AS NOTED ON
ELEVATIONS
ALL SEMI-EXPOSED SURFACES SHALL BE BLACK PLASTIC
LAMINATE.
INTERIOR FACE OF DIE WALLS TO BE FACED WITH BLACK
FRP.
SEAL ALL EXPOSED PLYWOOD EDGES AND MAINTAIN
MINIMUM 1/4" GAP FROM FLOOR TO PREVENT WICKING OF
WATER.
ALL SNEEZE GUARDS/ FOOD SHIELDS SHOWN SHOULD BE
INCLUDED WITHIN THE MILLWORK CONTRACTORS SCOPE OF
WORK.
ANY SIGNAGE & MENU FRAMES SHOULD BE INCLUDED
WITHIN THE MILLWORK'S SCOPE OF WORK
CONTRACTOR TO COORDINATE WITH EQUIPMENT
PROVIDER FOR INSTALLATION AND TESTING OF ALL
EQUIPMENT.
CONTRACTOR IS REQUIRED TO SET EQUIPMENT IN PLACE.
THIS INCLUDES, BUT IS NOT LIMITED TO, ALL OWNER SUPPLIED
"EXISTING" EQUIPMENT. CONTRACTOR TO VERIFY
EQUIPMENT DATA AS PROVIDED IN ELECTRICAL &
PLUMBING DRAWINGS TO MINIMIZE SLAB CORING
POSSIBLE. CONTRACTOR IS RESPONSIBLE FOR PLUMBING &
ELECTRICAL FEEDS TO EQUIPMENT.
PROVIDE P-LAM FACED VERTICAL APRON TO CONCEAL ALL
DROP IN EQUIPMENT AND SINKS. MOUNT ALL EQUIPMENT
CONTROLS TO CABINET FRAME AT APRON. SEE DETAILS.
COORDINATE LOCATIONS WITH EQUIPMENT.
INSIDE VERTICAL MILLWORK SURFACES ADJACENT TO
COOKING EQUIPMENT SHALL BE FINISHED w/ 20GA . TYPE
304 #4 MILL FINISH STAINLESS STEEL PANELS FASTENED TO
PLYWOOD BACKER. ALL JOINTS REQUIRE BATTEN STRIPS.
CONTRACTOR TO PROVIDE ENGINEERED SHOP DRAWINGS
INCLUDING PLAN LAYOUT DETAILS & SPECIFICATIONS FOR
ALL STRUCTURAL CONNECTIONS TO EXISTING BASE
BUILDING STRUCTURE FOR ARCHITECT'S REVIEW &
APPROVAL. ITEMS SHALL INCLUDE BUT NOT LIMITED TO WALL
BRACKET MOUNTING DETAILS, PICKPOINT CONNECTIONS
FOR SUSPENDED CEILING ELEMENTS, BEAM CLAMP,
UNISTRUT AND THREADED ROD DETAILS FOR EXHAUST
HOODS & OTHER SUSPENDED DESIGN ELEMENTS.
ALL EXPOSED BOLT & NUT CONNECTIONS ARE BOTH
FUNCTIONAL AND DECORATIVE. PAINT ALL FASTENERS TO
MATCH.
CALCULATE LOAD WEIGHT OF SUSPENDED OBJECTS TO
DETERMINE THE REQUIRED QUANTITY OF PICK POINT
LOCATIONS.
PROVIDE STAINLESS STEEL SUPPORT LEGS EVERY 4'-0" OR AS
REQUIRED TO AVOID DEFLECTION AND CRACKING OF
COUNTER SURFACE. SECURELY PIN LEG TO THE FLOOR AND
SEAL WITH SILICONE TO MAINTAIN WATERPROOFING BELOW
TILE. COORDINATE LOCATIONS SO AS NOT TO INTERFERE
WITH EQUIPMENT.
ALL EQUIPMENT MUST BE REVIEWED FOR HEIGHT SO AS NOT
TO INTERFERE WITH COUNTER HEIGHTS. ARCHITECT
RESERVES THE RIGHT TO CHANGE FOOT OR CASTER
SELECTION DURING SUBMITTAL TO KEEP HEIGHTS FORM
INTERFERING WITH COUNTERTOPS.
ALL CABINET DOOR HINGES TO BE CONTINUOUS PIANO
HINGES.
PROVIDE REINFORCEMENT TO COUNTERTOP EDGE OVER
LONG SPANS WHERE CUT OUTS FOR EQUIPMENT EXIST.
ALL STRUCTURAL HANGING ELEMENTS SHOULD BE RATED
FOR STRENGTH AND REVIEW IN SHOP DRAWINGS BY
STRUCTURAL ENGINEER.
ALL CUT OUTS FOR COUNTER TOP WELLS MUST HAVE
ROUNDED CORNERS PER MANUFACTURER'S INSTRUCTION.
CONTRACTOR TO VERIFY EQUIPMENT DATA AS PROVIDED
IN ELECTRICAL & PLUMBING DRAWINGS TO MINIMIZE SLAB
CORING, IF POSSIBLE.
PROVIDE HEAVY-DUTY REINFORCED CABINETS/ MILLWORK
STRUCTURE LOCATED UNDER BEVERAGE DISPENSER TYP.
THROUGH OUT PROJECT, PROVIDE P-LAM FACED VERTICAL
APRONS TO CONCEAL ALL DROP IN EQUIPMENT, SEE
DETAILS.
MOUNT ALL EQUIPMENT CONTROLS TO CABINET FRAME AT
APRON, SEE DETAILS.
MILLWORK FINISH INFORMATION
>MF-1: VERTICAL 1x MAPLE BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED PLYWOOD. 1" VERTICAL GAP BETWEEN
BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
COLOR: 3 COATS OF I-TR-W - COLOR TO BE SELECTED
>MF-2: PLASTIC LAMINATE
COLORS: TO BE SELECTED
>MF-3: SOLID SURFACE COUNTER TOP COLOR 1
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-4: SOLID SURFACE COUNTER TOP COLOR 2
MANUFACTURER: LG HI-MACS
COLOR: TO BE SELECTED FROM GRADES 5
>MF-5: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: PAINTED WITH CLEAR COAT SEALANT
>MF-6: ORNAMENTAL METAL
MANUFACTURER: BY MILLWORK SHOP
COLOR: BLACK
>MF-7: ORNAMENTAL METAL
EXPANDED METAL MESH
MANUFACTURER: BY MILLWORK SHOP
COLOR: TO BE SELECTED
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
GLAZING KEY
>GL-1:
STYLE: 1/4" FULLY TEMPERED GLASS
COLOR: CLEAR
>GL-2:
STYLE: CORRUGATED PLEXI GLASS
COLOR: OPAQUE
SHEET:
I-422
PHASE 2: ALTERATIONS & ADDITIONS
1/2" - 13 HEX BOLT
7/16" - WASHER
A.
RCNJ No. 2014-37-01C
C.
D.
PROVIDE APPROPRIATE CONTROL JOINTS TO FOR ALL WALL
TILE.
REFER TO THE TCNA HANDBOOK FOR TILE INSTALLATION
METHODS.
ALL GWB SURFACES TO HAVE PAINTED FINISH, AS SPECIFIED.
PROVIDE SCHLUTER CORNER GUARD PROTECTION AT ALL
WALL TILE CORNERS.
REFER TO INTERIOR ELEVATIONS FOR ADDITIONAL
INFORMATION ON STONE AND TILE.
PAINT ALL EXPOSED CONDUIT ON WALLS. COLOR TO BE
SELECTED.
FOR SIGNAGE INFORMATION REFER TO SHEET I-460.
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
B.
GENERAL NOTES
RAMAPO COLLEGE
OF NEW JERSEY
3/8" - 16 HEX BOLT
5/16" - WASHER
GENERAL NOTES
CT
}
A.
INTERIOR|ELEVATIONS
TE
6"+ BAR STOCK
5" & 6" CHANNEL
5/16" - 18 HEX BOLT
1/4" - WASHER
WALL FINISHES
SCOTT STUDENT CENTER
RESIDENTIAL DINING
4" BAR STOCK
5" BAR STOCK
1/4" - 20 HEX BOLT
3/16" - WASHER
MA
2" BAR STOCK
2" x 2" ANGLE
}
}
}
S TAT
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
INTERIOR ELEVATIONS
METAL CHANNEL AND BOLT SIZES
6' - 8"
3/23/2016 6:25:41 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
3/23/2016 6:25:49 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
5
1/2" LAG BOLT & WASHER,
PAINTED TO MATCH STEEL
METAL CHANNEL AND BOLT SIZES
6"+ BAR STOCK
5" & 6" CHANNEL
}
1/2" - 13 HEX BOLT
7/16" - WASHER
GYPSUM J MOLD FINISH EDGE
ALIGN
PAINTED STEEL PLATE, GRIND ALL
EDGES SMOOTH TO TOUCH.
3/4" PLASTIC LAMINATED
FIRE-RATED MDF
1/2" LAG BOLT & WASHER,
PAINTED TO MATCH STEEL
EXISTING PLANTER TO REMAIN
(BELOW)
TUBE STEEL, PAINTED. REFER
TO SPECIFICATIONS
5
FIREPLACE CORNER PLAN DETAIL
SEALED:
6
FRUIT STAND CORNER PLAN DETAIL
1 1/2" = 1'-0"
E
R EG
REFER TO SECTION & RCP FOR
HEIGHT ABOVE FINISH FLOOR
S
I
SECTION
1
PLANTER WALL @ CORNER
1/2" THROUGH BOLT TO 3"
STEEL TUBE FRAME, PAINTED
TO MATCH TUBE STEEL. REFER
TO SPECIFICATIONS
PAINTED 2"x2"x3/16" STEEL ANGLE,
GRIND ALL EDGES SMOOTH TO TOUCH.
3/4" PLASTIC LAMINATED
FIRE-RATED MDF
1/4" x 6" FLAT STOCK STEEL
LINE OF SOLID SURFACE TOP
TE
SCREEN ABOVE
C N
RK
N
1 1/2" = 1'-0"
NEW
OF O J
SEY
ER OR
3/4" PLASTIC LAMINATED
FIRE-RATED MDF
EXISTING BRICK WALL &
BACKUP TO REMAIN
ALIGN
3/8" - 16 HEX BOLT
5/16" - WASHER
ALL BOLTS ARE 12" O.C. ALONG THE ENTIRE MEMBER TYPICAL UNLESS OTHERWISE NOTED AND/OR WHERE
REQUIRED BY CONNECTIONS.
1/2" THROUGH BOLT TO 3"
STEEL TUBE FRAME
CONTINUOUS FLEXIBLE SEALANT
PAINTED 5/8" GYPSUM WALL BOARD
ON 3 5/8" 20 Ga. METAL STUDS
FRAMING @ 16" O.C.
5/16" - 18 HEX BOLT
1/4" - WASHER
No.
16419
CT
PROVIDE TURN
BUCKLE AS REQUIRED.
CORNER BEAD, TYPICAL
TE
EXISTING SECOND
FLOOR DECK
EXISTING WOOD PLANTER, RIGID
INSULATION, & BLOCKING TO BE
REMOVED
1/2" CEMENT WALL BOARD (BOTH
SIDES) ON 3 5/8" METAL STUDS
FRAMING @ 16" O.C. w/ DOUBLE
STUDS IN CORNERS. REFER TO I-101
FOR WALL TILE FINISH INFORMATION.
MA
2" BAR STOCK
2" x 2" ANGLE
PAINTED 3"x2"x3/16" STEEL ANGLE,
GRIND ALL EDGES SMOOTH TO TOUCH.
2x WOOD BLOCKING
AS REQUIRED
S TAT
PAINTED 5/8" GYPSUM WALL
BOARD ON 3 5/8" 20 Ga. METAL
STUDS FRAMING @ 16" O.C.
ATTACHED TO DECK ABOVE.
ALIGN
1/4" - 20 HEX BOLT
3/16" - WASHER
4" BAR STOCK
5" BAR STOCK
}
}
}
1-1/2" BAR STOCK
1-1/2" x 1-1/2" ANGLE
R E D A RC H
I
1/2" LAG BOLT & WASHER,
PAINTED TO MATCH STEEL
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
1 1/2" = 1'-0"
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
5
5
REFER TO SECTION & RCP FOR
HEIGHT ABOVE FINISH FLOOR
SECTION
3/4" OAK VENEERED FIRERATED MDF
1' - 8"
2x WOOD BLOCKING
AS REQUIRED
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
1/2" LAG BOLT & WASHER,
PAINTED TO MATCH STEEL
9 1/2"
11 1/2"
PAINTED 5/8" GYPSUM WALL
BOARD ON 3 5/8" 20 Ga. METAL
STUDS FRAMING @ 16" O.C.
ATTACHED TO DECK ABOVE.
PAINTED 3"x2"x3/16" STEEL ANGLE,
GRIND ALL EDGES SMOOTH TO TOUCH.
PAINTED 2"x2"x3/16" STEEL ANGLE,
GRIND ALL EDGES SMOOTH TO TOUCH.
PROVIDE WOOD BLOCKING
AS REQUIRED FOR
SCREENING FRAME BELOW
3"x3" ALUMINUM TUBE, PAINTED
SUSPENDED FROM DECK
ABOVE w/ THREADED ROD
3"x3" PAINTED TUBE
STEEL FRAME HUNG
BY THREADED ROD
FROM DECK ABOVE
7
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
HOST CORNER PLAN DETAIL
1 1/2" = 1'-0"
3/4" LAMINATED FIRE-RATED MDF
REVISIONS
LAY-IN CEILING, REFER TO I-200
SCREENING FAME BOLTED TO BLOCKING
3/4" LAMINATED
FIRE-RATED MDF
THROUGH BOLTED ADJUSTMENT SLEEVE
2"
LAY-IN CEILING
3/4" PLASTIC LAMINATED
FIRE-RATED MDF
PAINTED 2"x2" TUBE STEEL FRAME
PAINTED 8" STEEL CHANNEL,
CENTERED ON STUD WALL
2"
6 3/4"
ENGINEER:
DRAWN BY:
JNC
CHECKED BY:
JNC
TABS WELDED TO TUBE STEEL
FRAME TO CONNECT PANEL
3 5/8" METAL
DOUBLE STUD
PAINTED 18 Ga. EQUALLY
RABBETED HOLLOW METAL
FRAME - WRAP AROUND.
5/8" GYPSUM WALL
BOARD ON 3 5/8"
METAL STUDS
FRAMING @ 16" O.C.
CONTINUOUS SEALANT
(ALL SIDES)
STUD ANCHORS w/ WOOD
BLOCKING AS REQUIRED
8"
EXISTING RIGID INSULATION TO
REMAIN. REPLACE DAMAGED PIECES
AS REQUIRED FROM INSTALLATION OF
METAL PANEL SCREENS
4"
4"
1' - 0"
1' - 0"
EXISTING WOOD SURROUND TO REMAIN
PAINTED STEEL FLAT
STOCK SURROUND w/
1/2" HEX BOLT & 7/16"
WASHER (PAINTED TO
MATCH FLAT STOCK)
GRIND ALL EDGES
SMOOTH TO TOUCH
CLEAR
5/8" GYPSUM WALL
BOARD ON 3 5/8"
METAL STUDS
FRAMING @ 16" O.C.
2 1/2"
5/8" GYPSUM WALL
BOARD ON 3 5/8"
METAL STUDS
FRAMING @ 16" O.C.
2 1/2"
BOLT 2" STEEL FRAME TO TOP OF EXISTING
WOOD BLOCKING w/ STEEL PLATE
PAINTED 5/8" GYPSUM WALL
BOARD ON 3 5/8" 20 Ga.
METAL STUDS FRAMING @
16" O.C. ATTACHED TO
DECK ABOVE.
1' - 4"
EXISTING BRICK WALL &
BACKUP TO REMAIN
3' - 0"
MAIN LEVEL
0' - 0"
SIDE FOLDING SECURITY GATE. REFER
TO SPECIFICATIONS. COORDINATE
OPENING SIZE & POCKET LAYOUT w/
MANUFACTURER'S SPECIFICATIONS.
5' - 0"
VERIFY EXISTING WOOD BLOCKING
@ TOP OF WALL, REPLACE IF
STRUCTURALLY UNSOUND
10
MAIN LEVEL
0' - 0"
EXISTING FOOTING WALL
TO REMAIN
RES-LOWERLEVEL
-1' - 8"
RES-LOWERLEVEL
-1' - 8"
RES-LOWERLEVEL
-1' - 8"
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
2
PLANTER WALL
1 1/2" = 1'-0"
3
FIREPLACE WALL
1 1/2" = 1'-0"
4
BOARD WALL
1 1/2" = 1'-0"
9
SIDE FOLDING SECURITY GATE PLAN DETAIL
1 1/2" = 1'-0"
I-450
PHASE 2: ALTERATIONS & ADDITIONS
10"x8'-4"x1 3/4" 18 Ga. PAINTED
HOLLOW METAL DOOR w/
KEYED DEAD BOLT & THUMB
TURN LATCH ON INSIDE
RAMAPO COLLEGE
OF NEW JERSEY
1/8" PAINTED FLAT STOCK STEEL. HEIGHT TO
MATCH THAT OF EXISTING WOOD PLANTER.
GRIND ALL EDGES SMOOTH TO TOUCH.
MOUNT TO EXISTING WOOD PLANTER
SURROUND w/ 1/2" HEX BOLT & 7/16" WASHER
(PAINTED TO MATCH FLAT STOCK & ANGLE)
G
CONTINUOUS SEALANT
(ALL SIDES)
10' - 7 3/4"
2 1/2"
VENTLESS GAS FIREPLACE.
REFER TO SPECIFICATIONS
FULL HEIGHT CONTINUOUS
GEARED CONCEALED LEAF HINGE.
1' - 0"
3"x3" PAINTED STEEL ANGLE (GRIND ALL
EDGES SMOOTH TO TOUCH) MOUNTED TO
EXISTING WOOD PLANTER SURROUND w/
1/2" HEX BOLT & 7/16" WASHER (PAINTED TO
MATCH FLAT STOCK & ANGLE)
COORDINATE ELECTRICAL & DATA
CONNECTIONS FROM CEILING
ABOVE DOWN INSIDE EDGE OF
CHANNEL IN CONDUIT PAINTED
TO MATCH CHANNEL
2' - 5"
2"
1 1/2"
8 7/8"
1 1/2"
6 3/4"
PLANTER POT/ TRAY FOR INTERIOR PLANT/VINE
TO BE SPECIFIED & APPROVED BY ARCHITECT
PLAN DETAIL
1 1/2" = 1'-0"
10' - 7 3/4"
2"
9' - 0"
8' - 11 3/4"
8
REFER TO FIRE PLACE
MANUFACTURER'S INSTALLATION
GUIDE FOR SPECIFIC FRAMING
INSTRUCTIONS
SCOTT STUDENT CENTER
RESIDENTIAL DINING
3/4" PLASTIC LAMINATED
FIRE-RATED MDF
3/4" LAMINATED FIRE-RATED MDF
INTERIOR DETAILS
CONTINUOUS SEALANT
(BOTH SIDES)
PAINTED 5/8" GYPSUM WALL
BOARD (BOTH SIDES) ON 3 5/8" 20
Ga. METAL STUDS FRAMING @ 16"
O.C. ATTACHED TO DECK ABOVE.
PAINTED 5/8" GYPSUM WALL
BOARD ON 3 5/8" 20 Ga. METAL
STUDS FRAMING @ 16" O.C.
ATTACHED TO DECK ABOVE.
RIVER ROCK TO BE SPECIFIED &
APPROVED BY ARCHITECT
PAINTED 5/8" GYPSUM WALL BOARD
(BOTH SIDES) ON 3 5/8" 20 Ga. METAL
STUDS FRAMING @ 16" O.C. w/
DOUBLE STUDS @ CORNERS
RCNJ No. 2014-37-01C
WOOD BLOCKING
AS REQUIRED
3' - 4 7/8"
5' - 2 1/2"
VERIFY
7' - 3 1/2"
MESH PANEL BOLTED TO TABS, GRIND
ALL EDGES SMOOTH TO TOUCH.
MESH PANEL TO BE SPECIFIED &
APPROVED BY ARCHITECT
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
1/2" LAG BOLT & WASHER,
PAINTED TO MATCH STEEL
5
PAINTED 2"x2" TUBE STEEL
FRAME, BEYOND
EQ
EQ
3"x3" PAINTED STEEL ANGLE (GRIND ALL
EDGES SMOOTH TO TOUCH) MOUNTED TO
EXISTING WOOD PLANTER SURROUND w/ 1/2"
HEX BOLT & 7/16" WASHER (PAINTED TO
MATCH FLAT STOCK & ANGLE)
1/2"
OVHG
1/8" PAINTED FLAT STOCK STEEL. HEIGHT TO
MATCH THAT OF EXISTING WOOD PLANTER.
GRIND ALL EDGES SMOOTH TO TOUCH.
MOUNT TO EXISTING WOOD PLANTER
SURROUND w/ 1/2" HEX BOLT & 7/16" WASHER
(PAINTED TO MATCH FLAT STOCK & ANGLE)
3' - 6"
MA
R EG
EXISTING RIGID INSULATION TO
REMAIN. REPLACE DAMAGED PIECES
AS REQUIRED FROM INSTALLATION OF
METAL PANEL SCREENS
S
I
3' - 6"
E
TE
BOLT 2" STEEL FRAME TO TOP OF EXISTING
WOOD BLOCKING w/ STEEL PLATE
C N
RK
N
EXISTING WOOD SURROUND TO REMAIN
BANQUETTE, REFER TO I-500
FOR MORE INFORMATION
NEW
OF O J
SEY
ER OR
S TAT
SEALED:
No.
16419
CT
1 1/2"
RIVER ROCK TO BE SPECIFIED &
APPROVED BY ARCHITECT
PLANTER POT/ TRAY FOR INTERIOR PLANT/VINE
TO BE SPECIFIED & APPROVED BY ARCHITECT
8 3/4"
SOLID SURFACE TOP ON
3/4" PLYWOOD SUBSTRATE
TE
MESH PANEL w/ 1/2"x1/2" STEEL ANGLE
STOPS ON 1 1/2"x1 1/2" STEEL TUBE,
GRIND ALL EDGES SMOOTH TO
TOUCH. PAINTED FINISH ON ALL STEEL.
MESH PANEL TO BE SPECIFIED &
APPROVED BY ARCHITECT
1/2"
3/23/2016 6:25:52 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
R E D A RC H
I
VERIFY EXISTING WOOD BLOCKING
@ TOP OF WALL, REPLACE IF
STRUCTURALLY UNSOUND
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
EXISTING BRICK WALL &
BACKUP TO REMAIN
PAINTED 5/8" GYPSUM WALL
BOARD (BOTH SIDES) ON 3 5/8"
METAL STUDS FRAMING @ 16" O.C.
ALIGN CENTER OF WALL w/
CENTER OF COLUMN
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
MAIN LEVEL
0' - 0"
RES-LOWERLEVEL
-1' - 8"
5
4
KNEE WALL @ BANQUETTE
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
PLANTER RAILING
ENGINEER:
1 1/2" = 1'-0"
1 1/2" = 1'-0"
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
PAINTED STEEL CHANNEL
LIGHT FIXTURE, REFER TO I-201
& ELECTRICAL DRAWINGS.
3/4" LAMINATED FIRE-RATED MDF
WITH OAK VENEER
LAY-IN CEILING
5' - 5 3/4"
SOLID SURFACE (ALL SIDES) ON
3/4" PLYWOOD SUBSTRATE
5' - 2"
1/2" PLYWOOD
BLOCKING AS REQUIRED
2"x2" ALUMINUM TUBE FRAME
3/4" PLYWOOD TALL CABINET (NO
PARTICLEBOARD OR MDF) w/ PLASTIC
LAMINATE FINISH, BEYOND.
3"
SUSPENDED LIGHT FIXTURE, REFER
TO I-201 & ELECTRICAL DRAWINGS
2"
1 1/4"
1' - 11 1/2"
2' - 6"
2"x2" STEEL FRAME, CLEAR COATED.
BEYOND.
2"
1 1/4"
SECTION
SOLID SURFACE TOP w/
MINIMUM (2) LAYERS OF
3/4" PLYWOOD SUBSTRATE
4' - 0"
1/2" SOLID SURFACE ON (2)
LAYERS OF 3/4" PLYWOOD
7' - 8"
6"
1' - 4"
2' - 6"
CONTINUOUS SEALANT
2"
3 1/4"
SOLID SURFACE
COUNTERTOP w/ MINIMUM
(2) LAYERS OF 3/4"
PLYWOOD SUBSTRATE
1/2"
OVHG
SOLID SURFACE
COUNTERTOP ON (1)
LAYER OF 3/4"
PLYWOOD SUBSTRATE
2"
CONTINUOUS SEALANT
8"
2"
POS, PROVIDED BY OTHERS.
1/2"
OVHG
WALL TILE (BOTH SIDES) ON 1/2"
CEMENT BOARD & 3 5/8" METAL
STUDS FRAMING @ 16" O.C. REFER
TO I-102 FOR MORE INFORMATION
1' - 6"
2"
2"x2" ALUMINUM TUBE
FRAME, PAINTED. GRIND ALL
EDGES SMOOTH TO TOUCH
RAMAPO COLLEGE
OF NEW JERSEY
INTERIOR DETAILS
SUSPENDED LIGHT FIXTURE, REFER
TO I-201 & ELECTRICAL DRAWINGS
PROVIDE COUNTER TOP CORE CUT
OUT & GROMMET COVER FOR ALL
REQUIRED COUNTERTOP EQUIPMENT
POWER CORDS (TYPICAL).
2' - 10"
3' - 6"
SOLID SURFACE COUNTERTOP w/
MINIMUM (2) LAYERS OF 3/4" PLYWOOD
SUBSTRATE. SILICONE AT ALL COUNTER
TO VERTICAL SURFACE JOINTS.
3' - 2 3/4"
3' - 6"
3' - 6"
FIXED STOOL, REFER
TO I-500 FOR MORE
INFORMATION
PROVIDE ANGLE SUPPORT &
BLOCKING AS REQUIRED.
LOCATION FOR RECESSED
ELECTRICAL BOX & OUTLET.
3/4" PLYWOOD DIEWALL
CONSTRUCTION (NO PARTICLEBOARD
OR MDF) w/ PLASTIC LAMINATE FINISH
2' - 8"
FIXED STOOL, REFER TO I-500 FOR
MORE INFORMATION
7"
TILE BASE, TYP.
6"
5"
RES-LOWERLEVEL
-1' - 8"
MAIN LEVEL
0' - 0"
PROVIDE 1/4" GAP BETWEEN FLOOR
FINISH & VERTICAL PLYWOOD
CONSTRUCTION, FILL w/ CONTINUOUS
SILICONE BEAD TO SEAL JOINT AT
PLYWOOD TO FLOOR (TYPICAL).
PROVIDE PRESSURE TREATED 3/4"
PLYWOOD SHOE SECURED TO FLOOR
(TYPICAL).
3
HIGH COUNTER SECTION
1 1/2" = 1'-0"
2
LOUNGE TABLE SECTION
1 1/2" = 1'-0"
1
HOST STATION SECTION
1 1/2" = 1'-0"
MAIN LEVEL
0' - 0"
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
I-451
PHASE 2: ALTERATIONS & ADDITIONS
2' - 6"
JNC
STAINED SOLID WOOD PLANKING w/ VARIABLE
WIDTHS & LENGTHS. COORDINATE w/
ARCHITECT FOR SIZES & FINISH. ATTACHED TO
C-CHANNEL ABOVE w/ THREADED ROD,
PAINTED.
LINE OF CEILING BEYOND,
REFER TO I-200.
3"x3" PAINTED TUBE
STEEL FRAME HUNG
BY THREADED ROD
FROM DECK ABOVE
CHECKED BY:
SCOTT STUDENT CENTER
RESIDENTIAL DINING
3/4" LAMINATED FIRE-RATED MDF
JNC
RCNJ No. 2014-37-01C
1' - 4"
2"x2" ALUMINUM TUBE, PAINTED.
SUSPENDED FROM STEEL CHANNELS
ABOVE w/ THREADED ROD, EYE
SOCKETS, & BEAM CLAMPS
DRAWN BY:
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
8"
CURVED STEEL C-CHANNEL
3/23/2016 6:25:55 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
I
TE
CT
No.
16419
TE
R EG
S
C N
RK
N
MA
E
NEW
OF O J
SEY
ER OR
S TAT
SEALED:
R E D A RC H
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
PAINTED 5/8" GYPSUM
WALL BOARD ON 3 5/8" 20
Ga. METAL STUDS FRAMING
@ 16" O.C. ATTACHED TO
DECK ABOVE.
1' - 6"
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
CORNER BEAD, TYPICAL
ENGINEER:
6"
PROVIDE WOOD BLOCKING
AS REQUIRED FOR
SCREENING FRAME BELOW
3' - 10"
SCREENING FAME BOLTED
TO BLOCKING
1" 2"
4"
3' - 6"
7"
THROUGH BOLTED
ADJUSTMENT SLEEVE
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
REVISIONS
1' - 0"
2"
6"
PAINTED 2"x2" TUBE
STEEL FRAME
1' - 9 1/2"
SUSPENDED LIGHT FIXTURE, REFER
TO I-201 & ELECTRICAL DRAWINGS
TRANSLUCENT CORRUGATED PANEL
w/ 1/4"x3/4" STEEL STOPS ON
CURVED 2"x2" STEEL TUBE, GRIND
ALL EDGES SMOOTH TO TOUCH.
PAINTED FINISH ON ALL STEEL.
DRAWN BY:
JNC
CHECKED BY:
JNC
2"
7"
GLASS PANEL w/ 1/2"x1/2"
PAINTED STEEL ANGLE STOPS
PAINTED STEEL PANEL w/ 1/2"x1/2"
PAINTED STEEL ANGLE STOPS
2" 1"
2x STEEL SQUARE TUBING
ATTACHED TO WALL BELOW
WITH ANGLE AND BOLT
CONNECTION
11' - 0"
2"
2"
2"x2" STEEL FRAME,
CLEAR COATED.
5"
STEEL FLAT STOCK TOP
WITH BOLT AND WASHER
DETAIL. PROVIDE
BLOCKING AS REQUIRED
BOLT 2" STEEL FRAME TO TOP
OF EXISTING WOOD
BLOCKING w/ STEEL PLATE
2"x2" CLEAR COATED STEEL
FRAMED CABINET w/ GLASS
DOORS (FULL HEIGHT PIANO
HINGE & MAGNETIC HOLDS) &
ANGLED MAPLE SHELVING WITHIN
EQ
WALL TILE (BOTH SIDES) ON
1/2" CEMENT BOARD & 3 5/8"
METAL STUDS FRAMING @ 16"
O.C. REFER TO I-102 FOR
MORE INFORMATION
2"
SOLID SURFACE COUNTERTOP
w/ MINIMUM (2) LAYERS OF
3/4" PLYWOOD SUBSTRATE
PAINTED 5/8" GYPSUM
WALL BOARD ON 3 5/8"
20 Ga. METAL STUDS
FRAMING @ 16" O.C.
2' - 0"
VERTICAL 1x MAPLE
BOARDS ON 3/4" PLASTIC
LAMINATED FINISHED
PLYWOOD. 1" VERTICAL
GAP BETWEEN BOARDS.
(3) SIZES: 1x2, 1x4, 1x6.
CARPET TILE, REFER TO I-102
1' - 4"
2"
4' - 2"
5' - 0"
EQ
1' - 6"
PAINTED STEEL PANEL w/
1/2"x1/2" PAINTED STEEL
ANGLE STOPS
PAINTED 5/8" GYPSUM
WALL BOARD (BOTH SIDES)
ON 3 5/8" METAL STUDS
FRAMING @ 16" O.C.
CONTINUOUS SEALANT,
ALL SIDES
10°
FURNITURE BY OTHERS
1/2"
OVHG
2' - 0"
4' - 4"
SOLID SURFACE COUNTERTOP
w/ MINIMUM (2) LAYERS OF
3/4" PLYWOOD SUBSTRATE,
BEYOND.
3' - 8"
4' - 0"
8' - 0"
2"
1/2" SOLID SURFACE ON (2)
LAYERS OF 3/4" PLYWOOD
PROVIDE ADEQUATE
BLOCKING WHERE REQUIRED
3/4" PLYWOOD BOX
BASE CABINET
3/4" PLYWOOD ON 6" METAL
STUDS FRAMING @ 16" O.C.
6"
6 3/4"
TILE BASE, TYP.
8' - 8 1/2"
RES-LOWERLEVEL
-1' - 8"
MAIN LEVEL
0' - 0"
MAIN LEVEL
0' - 0"
DIAMETER
ISSUED:
03.24.2016
3
CIRCLE BOOTH SECTION
1 1/2" = 1'-0"
2
FRUIT STAND SECTION
1 1/2" = 1'-0"
1
HOST WALL SCREEN SECTION
DESCRIPTION:
BID DOCUMENTS
1 1/2" = 1'-0"
SHEET:
I-452
PHASE 2: ALTERATIONS & ADDITIONS
1' - 11 1/2"
RCNJ No. 2014-37-01C
2"
RAMAPO COLLEGE
OF NEW JERSEY
1' - 9 1/2"
2' - 3 1/2"
10"
STEEL FLAT STOCK SECURED
TO WALL WITH BOLT &
WASHER CONNECTION,
TYP. BEYOND.
MESH PANEL BOLTED TO
TABS, GRIND ALL EDGES
SMOOTH TO TOUCH.
MESH PANEL TO BE SPECIFIED
& APPROVED BY ARCHITECT
INTERIOR DETAILS
TABS WELDED TO TUBE STEEL
FRAME TO CONNECT PANEL
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
DIMENSIONAL 8" STEEL
LETTERS, CLEAR COATED.
MOUNTED ON WOOD BOARD
SECURED TO WALL WITH BOLT
AND WASHER CONNECTIONS
6' - 8"
PAINTED 5/8" GYPSUM WALL
BOARD ON 3 5/8" 20 Ga. METAL
STUDS FRAMING @ 16" O.C.
1' - 2"
2x STEEL SQUARE TUBING
ATTACHED TO STRUCTURE
ABOVE WITH WELDED AND
BOLTED CONNECTION
2' - 0"
DIAMETER
SCOTT STUDENT CENTER
RESIDENTIAL DINING
8' - 7"
2"
8' - 6"
3/23/2016 6:26:00 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
13' - 7 1/4"
12' - 7 1/4"
5' - 1 3/8"
4' - 9 3/8"
2
3' - 0"
I-452
2' - 8"
6' - 0"
SEALED:
I
S
TE
No.
16419
CT
R EG
2" x 2" STEEL FRAME
C N
RK
TE
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
2" x 2" STEEL FRAME
E
NEW
OF O J
MA
S TAT
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
3' - 8"
4' - 0"
4' - 8"
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
4' - 4"
7' - 0"
7' - 4"
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
N
10' - 0 1/2"
5' - 8"
SEY
ER OR
11' - 0 1/2"
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
R E D A RC H
I
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
2" x 2" STEEL FRAME
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
2
3
HOST DESK - FRAMED GRAPHIC
VINYL GRAPHIC ADHERED TO GWB WALL
IMAGE TO BE SELECTED BY ARCHITECT
FRUIT STAND FRONT - FRAMED GRAPHIC
1/2" = 1'-0"
4
FRUIT STAND BACK - FRAMED GRAPHIC
1/2" = 1'-0"
ARCHITECT:
1/2" = 1'-0"
1/4" x 6" STEEL FLAT STOCK FRAME
SECURED WITH BOLT AND WASHER DETAIL
1
RAMP - FRAMED GRAPHIC
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
1/2" = 1'-0"
ENGINEER:
3' - 4"
3' - 4"
3' - 4"
3' - 0"
3' - 0"
3' - 0"
3' - 4"
3' - 4"
3' - 4"
3' - 4"
3' - 4"
3' - 0"
3' - 0"
3' - 0"
3' - 0"
3' - 0"
1' - 6"
3' - 4"
5' - 0"
11
SIGN WING VINYLS
1/2" = 1'-0"
WF-3 IN MAPLE FRAME
WF-3 IN MAPLE FRAME
WF-3 IN MAPLE FRAME
WF-3 IN MAPLE FRAME
72"
MEDITERRANEAN
17"
17"
HOMETOWN
72"
WIRE CONNECTION TO METALC-CHANNEL ABOVE
WIRE CONNECTION TO METALC-CHANNEL ABOVE
WIRE CONNECTION TO METALC-CHANNEL ABOVE
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
72"
81"
SALAD
72"
WF-3 IN MAPLE FRAME
69"
17"
SANDWICHES
WF-3 IN MAPLE FRAME
BIRCH TREE INN SIGN
1/2" = 1'-0"
72"
WIRE CONNECTION TO METALC-CHANNEL ABOVE
81"
12
24"
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
24"
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
24"
FRUIT STAND SIGN
1/2" = 1'-0"
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
GRILL
4' - 4"
4' - 0"
4' - 0"
BIRCH TREE INN
108"
8" METAL LETTERING APPLIED TO WF-3.
LETTERS AND FONT TO BE SELECTED
17"
4' - 4"
4 DIFFERENT VINYL
GRAPHICS. IMAGE TO BE
SELECTED BY ARCHITECT
WIRE CONNECTION TO METAL PIPE ABOVE
24"
4' - 4"
4' - 0"
1' - 2"
3' - 4"
5' - 4"
60"
2" STEEL FRAME
I-452
WIRE CONNECTION TO METAL PIPE ABOVE
WF-3 IN MAPLE FRAME
8" METAL LETTERING APPLIED TO
WOOD SIGN BOARD
WF-1 ON PLYWOOD
SUBSTRATE
2
WIRE CONNECTION TO METAL PIPE ABOVE
17"
WOK
DIMENSIONAL 8" STEEL LETTERS, CLEAR
COATED. FONT AND LETTERS TO BE SELECTED
BY ARCHITECT
WIRE CONNECTION TO METAL PIPE ABOVE
17"
69"
Z-CLIP FRAME TO WALL ABOVE NEW GATE ENTRY
TO RESIDENTIAL DINING
WF-3 IN MAPLE FRAME
DESSERT
60"
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
13
ADD/ALT 1
STATION SIGNAGE
1/2" = 1'-0"
SHEET:
I-460
PHASE 2: ALTERATIONS & ADDITIONS
1' - 6"
RCNJ No. 2014-37-01C
1' - 6"
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
1' - 6"
RAMAPO COLLEGE
OF NEW JERSEY
1' - 10"
1/2" = 1'-0"
MAPLE BACK BOARD, CLEAR
COATED. SECURED TO WALL
WITH BOLT AND WASHER
CONNECTIONS
ADD/ALT 1
PIZZA
4' - 0"
4' - 4"
1' - 10"
ADD/ALT 1
2" x 2" STEEL FRAME
10
AGK
MY ZONE 5 - FRAMED GRAPHICS
6' - 8"
72"
17"
1' - 10"
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
1/2" = 1'-0"
17"
ADD/ALT 1
1' - 10"
8
1/2" = 1'-0"
FRAME ASSEMBLY TO BE
ZCLIPPED TO MILLWORK
BEHIND. PROVIDE
APPROPRIATE FASTENERS
AND BLOCKING IF
ACCESSIBLE
WOK 6 - FRAMED GRAPHICS
CHECKED BY:
2" x 2" STEEL FRAME
MY ZONE 2 - FRAMED GRAPHICS
ADD/ALT 1
1/2" = 1'-0"
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
3' - 0"
9
7
BACK LINE - FRAMED GRAPHIC
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
2" x 2" STEEL FRAME
AGK
SCOTT STUDENT CENTER
RESIDENTIAL DINING
ADD/ALT 1
1/2" = 1'-0"
3' - 0"
ADD/ALT 1
DRAWN BY:
SIGNAGE & GRAPHICS
6
BACK LINE - FRAMED GRAPHICS
REVISIONS
2" x 2" STEEL FRAME
2" x 2" STEEL FRAME
2" x 2" STEEL FRAME
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
16"
VINYL GRAPHIC. IMAGE TO
BE SELECTED BY ARCHITECT
5
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
4' - 0"
4' - 4"
4' - 0"
4' - 0"
4' - 0"
4' - 4"
FRAME ASSEMBLY TO BE
ZCLIPPED TO WALL.
PROVIDE APPROPRIATE
FASTENERS AND BLOCKING
IF ACCESSIBLE
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
3/23/2016 6:27:30 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
FURNITURE NOTES
SEATING COUNTS
RESIDENTIAL:
DINING SEATS: 280
ACCESSIBLE: 4
RETAIL:
DINING SEATS: 384
ACCESSIBLE: 6
BARRIER FREE
NEW JERSEY ADMINISTRATIVE CODE
TITLE 5. COMMUNITY AFFAIRS
CHAPTER 23. UNIFORM CONSTRUCTION CODE
SUBCHAPTER 7. BARRIER FREE SUBCODE
N.J.A.C. 5:23-7.11 (2015)
SEALED:
I
S
TE
2. In dining areas of occupancies of Use Groups A-2 and A-3,
the total floor area allotted for seating and tables shall be
accessible, except as follows:
i. Where fixed or built-in seats and tables are provided, at
least five percent, but not fewer than one, of the seats and
tables shall be accessible. Where more than one accessible
seat and table is provided, they shall be dispersed.
AREA OF ALTERATIONS
ii. In buildings without elevators, an accessible route to a
raised or lowered dining area of less than 3,000 square feet is
not required provided that the raised or lowered dining area
contains less than 25 percent of the total dining area and the
same services are available on the accessible level.
EXISTING TO REMAIN
No.
16419
CT
MA
R EG
1. Where services and facilities are provided in areas that are
not required to be accessible, the same services and
facilities shall be provided in an accessible area and shall be
accessible.
C N
RK
N
S TAT
E
SEY
ER OR
(A) Occupancies of Group A shall be accessible as follows:
NEW
OF O J
TE
5:23-7.11 Requirements applicable to specific nonresidential
Groups and Group R-1
R E D A RC H
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
3. Accessible spaces for wheelchairs shall be provided in
each assembly area in accordance with the following table.
0
0
Capacity of Seating
4-25
26-50
51-300
301-500 over 500
Accessible Seating
1
2
4
6
6 PLUS 1 FOR
EACH100 OVER 500
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
GENERAL NOTES
4.
5.
6.
7.
D
8.
REVISIONS
DRAWN BY:
AGK.
CHECKED BY:
AGK.
ND BATTER
01050F
NA
A
KR
BREAD
F
AREA OF ALTERATIONS
EXISTING TO REMAIN
EXISTING TO REMAIN
AREA OF ALTERATIONS
EXISTING FURNITURE
F
AREA OF ALTERATIONS
1
FURNITURE PLAN
EXISTING TO REMAIN
RAMAPO COLLEGE
OF NEW JERSEY
BIN ET,
FLOOR PLAN - FURNITURE
CA
SCOTT STUDENT CENTER
RESIDENTIAL DINING
00
N
ISSUED:
03.24.2016
1/8" = 1'-0"
DESCRIPTION:
BID DOCUMENTS
SHEET:
I-500
PHASE 2: ALTERATIONS & ADDITIONS
3.
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
RCNJ No. 2014-37-01C
2.
UPHOLSTERED FURNITURE MUST MEET CAL 117 STANDARDS
FOR FLAME SPREAD.
FURNITURE INSTALLER TO WORK WITH CONTRACTOR AND
PROJECT MANAGER TO SET UP DELIVERY AND INSTALL TO
BE WITH IN THE CONSTRUCTION SCHEDULE.
INSTALLER TO REMOVE ALL CARDBOARD, PACKING
MATERIALS, AND OTHER RELATED DEBRIS FROM PROJECT
SITE AND RECYCLE AS MUCH AS IS POSSIBLE.
PROVIDE FURNITURE GLIDES WHICH ARE MECHANICALLY
FASTENED TO CHAIR AND TABLE BASE BOTTOMS.
FURNITURE GLIDES MUST BE DURABLE AND REPLACEABLE.
FURNITURE GLIDES MUST OF A MATERIAL THAT CAN BE USED
ON RESILIENT FLOORING.
PROVIDE A LABELED BOX OF 100 ADDITIONAL CHAIR
GLIDES.
PROVIDE A LABELED BOX OF 20 ADDITIONAL TABLE BASE
GLIDES.
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
1.
3/23/2016 6:27:57 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
I
TE
CT
No.
16419
TE
R EG
S
C N
RK
N
MA
E
NEW
OF O J
SEY
ER OR
S TAT
SEALED:
R E D A RC H
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED REPRODUCTION OR
UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS SHALL BE SCALED OFF DRAWINGS.
ALL MEASUREMENTS SHALL BE VERIFIED IN FIELD.
ARCHITECT:
1656 Massachusetts Ave. | Lexington, MA 02420
Tel: 781-652-0114 | connorarchitecture.com
ENGINEER:
49 Court Street | P.O. Box 1980 | Binghamton, NY 13902
Tel: 607-723-9421 | mjinc.com
AGK
RAMAPO COLLEGE
OF NEW JERSEY
3 DIMENSIONAL VIEW
ISSUED:
03.24.2016
DESCRIPTION:
BID DOCUMENTS
SHEET:
I-800
PHASE 2: ALTERATIONS & ADDITIONS
CHECKED BY:
RCNJ No. 2014-37-01C
AGK
SCOTT STUDENT CENTER
RESIDENTIAL DINING
DRAWN BY:
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
REVISIONS