EVAL-ADG2128EBZ User Guide
UG-341
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board—I2C, CMOS, 8 × 12 Analog Switch Array with Dual/Single Supplies
The ADG2128 has a maximum difference of 15 V between its
inputs, VDD and VSS; take care not to exceed this parameter
when connecting the power supplies.
FEATURES
Full featured evaluation board for ADG2128
Various link options
Direct hookup to USB port of PC
PC software for control of switches
Can be used with or without PC
The evaluation board interfaces to the USB port of a PC.
Software is available with the evaluation board that allows the
user to easily program the ADG2128.
GENERAL DESCRIPTION
This user guide describes the evaluation board for the ADG2128
I2C, CMOS, 8 × 12 analog switch array with dual/single supplies.
The array is bidirectional; therefore, the rows and columns can
be configured as either inputs or outputs, and any number of
combinations can be active at one time.
Full data on the ADG2128 can be found in the data sheet, which
should be consulted in conjunction with this document when
using the evaluation board.
EVALUATION BOARD SETUP
POWER SUPPLY INPUTS
USB
CONNECTOR
DGND
VBUS
CONTROLLER
3.3V
LINEAR
REGULATOR
VL
VSS
GND
VDD
CY7C68013
SDA
SCL
SDA
Y0
ADG2128
I/O
CMOS ANALOG
SWITCH ARRAY
RESET
X0
Y7
X11
I/O
Figure 1. Evaluation Board Setup
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. C | Page 1 of 13
05769-001
SCL
UG-341
EVAL-ADG2128EBZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1 Link Options ..................................................................................4 General Description ......................................................................... 1 Evaluation Board Software Quick Start Procedures .....................6 Evaluation Board Setup ................................................................... 1 Software Installation .....................................................................6 Revision History ............................................................................... 2 Software Operation .......................................................................6 Evaluation Board Photograph......................................................... 3 Evaluation Board Schematics and Artwork ...................................8 Evaluation Board Hardware ............................................................ 4 Ordering Information .................................................................... 12 Power Supplies .............................................................................. 4 Bill of Materials ........................................................................... 12
REVISION HISTORY
10/15—Rev. B to Rev. C
Added Evaluation Board Photograph Section and Figure 2;
Renumbered Sequentially................................................................ 3
Changes to Evaluation Board Software Quick Start Procedures
Section, Software Installation Section, Software Operation
Section, Setting the I2C Address Section, and Figure 2 to
Figure 4 .............................................................................................. 5
Added Reinitialize the Software Section ....................................... 5
Changes to LDSW (Load Switch) Section, Switch Status Section,
Figure 5, and RESET Function Section ......................................... 6
Added All On Function Section ..................................................... 6
11/11—Rev. A to Rev. B
Changes to Evaluation Board Schematics Section ........................7
8/07—Rev. 0 to Rev. A
Changes to Figure 1...........................................................................1
Changes to Table 4.......................................................................... 11
Changes to Ordering Guide .......................................................... 12
7/06—Revision 0: Initial Version
Rev. C | Page 2 of 13
EVAL-ADG2128EBZ User Guide
UG-341
05769-100
EVALUATION BOARD PHOTOGRAPH
Figure 2. EVAL-ADG2128EBZ Evaluation Board
Rev. C | Page 3 of 13
UG-341
EVAL-ADG2128EBZ User Guide
EVALUATION BOARD HARDWARE
POWER SUPPLIES
The EVAL-ADG2128EBZ can be operated with both single and
dual supplies. The device is specified to operate in single-supply
mode at 12 V ± 10% and 8 V ± 10% operation. It is also
specified to operate at ±5 V dual supply. The following details
how these supplies are applied to the evaluation board:



VL provides the digital supply for the ADG2128 and all
digital circuitry on the board. This supply can be applied
externally, or the USB port can be used to power the digital
circuitry (with Link 5 inserted). In this case, the logic
supply power is 3.3 V.
Connect 8 V or 12 V between the AVDD and AGND inputs
for the positive analog supply (VDD) of the ADG2128. Note
that the maximum single supply that the chip can handle is
15 V. In this case, AVSS must equal 0 V. In the case of an 8 V
or 12 V supply, negative voltage can be applied to AVSS if
VDD to VSS is a maximum of 15 V.
Connect −5 V between the AVSS and AGND inputs for the
negative supply (VSS) of the ADG2128.
Both AGND and DGND inputs are provided on the board. The
AGND and DGND planes are connected at one location close to
the ADG2128. To avoid ground loop problems, it is recommended
not to connect AGND and DGND elsewhere in the system.
Each supply is decoupled to the relevant ground plane with
10 μF and 0.1 μF capacitors. Each device supply pin is also
decoupled with a 10 μF and a 0.1 μF capacitor pair to the
relevant ground plane.
LINK OPTIONS
Prior to using the board, a number of link and switch options
must be set for the required operating setup. These link option
functions are described in Table 1.
Table 1. Link Options
Link No.
LK1
LK2
LK3
LK4
LK5
Function
This link is for choosing the LSB bit of the address of the chip on the USB I2C interface. Note that the I2C address must be set before
the evaluation software is launched.
When this link is inserted, the address bit is set to 0.
When this link is removed, the address bit is set to 1.
This link is for choosing the second LSB bit of the address of the chip on the USB I2C interface. Note that the I2C address must be
set before the evaluation software is launched.
When this link is inserted, the address bit is set to 0.
When this link is removed, the address bit is set to 1.
This link is for choosing the third LSB bit of the address of the chip on the USB I2C interface. Note that the I2C address must be set
before the evaluation software is launched.
When this link is inserted, the address bit is set to 0.
When this link is removed, the address bit is set to 1.
This link selects whether the supply at VSS is sourced from ground or from the input AVSS. If it is sourced from ground, it is a
single-supply system.
Position A: VSS sourced from AVSS.
Position B: VSS sourced from ground.
This link selects whether the logic supply power is from the USB power (when connected to a PC) or from the user-supplied VL
(when used as a standalone unit).
When this link is inserted, the logic power supply is from the USB power.
When this link is removed, the logic power supply is from the user-supplied VL.
Rev. C | Page 4 of 13
EVAL-ADG2128EBZ User Guide
UG-341
Link Setup Options for PC Control
The default setup for the EVAL-ADG2128EBZ is to be controlled
by the PC via the USB port. The default link options are listed
in Table 2.
Table 2. Default Link Options
Link No.
LK1
LK2
LK3
LK4
LK5
Option
Inserted—the LSB is 0.
Inserted—the second LSB is 0.
Inserted—the third LSB is 0.
Position A—AVSS is supplying the power to VSS.
Inserted—the logic power supply is from USB power.
Table 3 lists the link options that must be set to operate the
evaluation board without a PC.
Table 3. Link Setup Options for Control Without a PC
Link No.
LK1
LK2
LK3
LK4
LK5
Option
User configurable—does not affect whether the
board is connected to a PC or not.
User configurable—does not affect whether the
board is connected to a PC or not.
User configurable—does not affect whether the
board is connected to a PC or not.
User configurable—does not affect whether the
board is connected to a PC or not.
Removed.
Link Setup Options for Control Without a PC
The EVAL-ADG2128EBZ can also be used as a standalone board.
This option is for PC users who do not have a USB port or for
users who want to connect the board to their entire system.
Switches are turned on and off via the I2C bus. The read/write
procedures are provided in the ADG2128 data sheet and should be
consulted when using this evaluation board in its standalone mode.
Rev. C | Page 5 of 13
UG-341
EVAL-ADG2128EBZ User Guide
EVALUATION BOARD SOFTWARE QUICK START PROCEDURES
The ADG2128 evaluation kit includes self-installing software
on the CD-ROM. The evaluation software must be installed
before connecting the evaluation board to the USB port of the
PC to ensure that the evaluation board is correctly recognized
when connected to the PC.
SOFTWARE INSTALLATION
If the ADG2128 evaluation board is not connected to the USB
port when the software is launched, a Hardware Select dialog
box displays (shown in Figure 4). Connect the evaluation board
to the USB port of the PC, wait for a few seconds, click Rescan,
and then click Select. The Configuration tab of the evaluation
software then displays as shown in Figure 3.
To install the software
1.
2.
3.
4.
Start Windows® and insert the CD. The installation
software should launch automatically. If it does not, use
Windows Explorer to locate the file setup.exe on the CD.
Double-click this file to start the installation procedure.
At the prompt, select a destination directory. By default,
it is C:\Program Files\Analog Devices\ADG2128.
After the directory is selected, the installation procedure
copies the files into the relevant directories on the hard
drive. The installation program creates a program group
called Analog Devices with a subgroup called ADG2128
in the Start menu of the taskbar.
After the installation of the evaluation software is complete,
a welcome window displays for the installation of the ADI
PAD Drivers. Click Install to install the drivers.
After the installation of the drivers, power up the ADG2128
evaluation board as described in the Evaluation Board
Hardware section. Then, connect it to the USB port of the
PC using the supplied cable.
SOFTWARE OPERATION
Figure 4. Hardware Select Dialog Box
Reinitialize Software
In the Configuration tab, click Reinitialize Software to reset
the software to its default state. Reinitialize the software
whenever the evaluation board is reconnected to the PC or a
new evaluation board is to be used.
Setting the I2C Address
The device address can be set in the Device Address tab (shown
in Figure 5).
To launch the software, click Start > All Programs > Analog
Devices > ADG2128 > ADG2128 Evaluation Software. The
Configuration tab of the evaluation software then displays as
shown in Figure 3.
Figure 5. Device Address Tab
Figure 3. Configuration Tab
Set the device address by clicking the relevant bit. Click Set
Device Address to update the device address in the software.
Note that the address set in the software must correspond to
the address set with the jumpers on the evaluation board. The
address must be set for the evaluation board software to work.
Rev. C | Page 6 of 13
EVAL-ADG2128EBZ User Guide
UG-341
LDSW (Load Switch)
If the load switch function in the Configuration tab is on, the
switches can be updated simultaneously (as an example, for the
RGB colors in video switching). Otherwise, if the load switch
is off, the switch condition updates upon completion of each
I2C write, that is, immediately upon clicking an LED in Analog
Crosspoint Switch Control in the Configuration tab. The
LED is green if the switch is on and black if the switch is off.
If the load switch is on, clicking an LED in Analog Crosspoint
Switch Control stores the switch status temporarily until
Update Switches is clicked. When clicked, a black LED becomes
red, which indicates that the switch is to be turned on, and a
green LED becomes dark green, which indicates that the switch
is to be turned off. All switches are then updated simultaneously
upon clicking Update Switches. The red LEDs then become
green, and the dark green LEDs become black, indicating that
the switches are now on and off, respectively.
Figure 6. Switch Status Tab
Switch Status
RESET Function
To see what the status of the switch array is at any given time,
click the Switch Status tab (shown in Figure 6). The green LED
in the Analog Crosspoint Switch Status indicates that the switch
is on, and the black LED indicates that the switch is off.
There is a RESET button on the board (see RESET on the Figure 8
schematic) that can be used to reset the switch array. Alternatively,
clicking Reset All (Off) in the software Configuration tab resets
all the switches.
All On Function
Clicking All On in the software Configuration tab turns on all
the switches.
Rev. C | Page 7 of 13
C13
10UF
5VUSB
Figure 7. Schematic of USB Controller Circuitry
0.1UF
C3
SHIELD
ADP3303-3.3
8
OUT1
7 IN1
OUT2
5 IN2
SD ERROR
GND NR
U5
4
J1
USB-MINI-B
1
VBUS
2
D3
D+
4
IO
5
GND
C6
C7
C8
C19
C20
C21
C9
0.1UF
R6
75
1
2
6
3
C16
0.1UF
C14
10UF
+3.3V
+3.3V
IFCLK
RSVD
RDY0/*SLRD
RDY1/*SLWR
PA0/INT0
PA1/INT1
PA2/*SLOE
PA3/*WU2
PA4/FIFOADR0
PA5/FIFOADR1
PA6/*PKTEND
PA7/*FLD/SLCS
D4
3.3V
PB0/FD0
PB1/FD1
PB2/FD2
PB3/FD3
PB4/FD4
PB5/FD5
PB6/FD6
PB7/FD7
PD0/FD8
PD1/FD9
PD2/FD10
PD3/FD11
PD4/FD12
PD5/FD13
PD6/FD14
PD7/FD15
18
19
20
21
22
23
24
25
45
46
47
48
49
50
51
52
+3.3V
XTALIN
XTALOUT
5
4
16
SDA 15
SCL
29
CTL0/*FLAGA 30
CTL1/*FLAGB 31
CTL2/*FLAGC
U3
DD+ CY7C68013-CSP
CLKOUT
RESET
*WAKEUP
R11
1K
R10
10K
13
14
1
2
33
34
35
36
37
38
39
40
9
8
54
42
44
C23
C18
0.1UF
C15
0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF
C5
+3.3V
DGND
C4
10UF
R5
75
0.1UF
R7
0R
2.2UF
+3.3V
AGND
6
+3.3V
3
AVCC
7
11
17
27
32
43
55
VCC
VCC
VCC
VCC
VCC
VCC
VCC
GND
GND
GND
GND
GND
GND
GND
10
12
26
28
41
53
56
Rev. C | Page 8 of 13
C17
22PF
U2
24LC64
1
2 A0
3 A1
4 A2
VSS
24 MHZ
XTAL1
SCL
SDA
8
VCC 7
WP 6
SCL 5
SDA
C22
0.1UF
+3.3V
C10
22PF
T1
T2
T3
05769-005
+3.3V
UG-341
EVAL-ADG2128EBZ User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
AVSS
Rev. C | Page 9 of 13
Figure 8. Schematic of ADG2128 Circuitry
Y6_Y7-B
Y6_Y7-A
Y4_Y5-B
Y4_Y5-A
Y2_Y3-B
Y2_Y3-A
Y0_Y1-B
Y0_Y1-A
X4_X5-B
X4_X5-A
X2_X3-B
X2_X3-A
X0_X1-B
X0_X1-A
A
B
4
3
4
3
4
3
4
3
4
3
4
3
4
3
2
1
2
1
2
1
2
1
2
1
2
1
2
1
DGND
R21
R20
R19
R18
R17
R16
R15
R14
R13
R12
R4
R3
R2
R1
C11
0.1UF
+
VSS
6V3
10UF
C12
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AGND
Y7
Y6
Y5
Y4
Y3
Y2
Y1
Y0
X5
X4
X3
X2
X1
X0
NC
GND
X6
X7
X8
X9
X10
X11
NC
VDD
VL
SDA
SCL
A0
A1
A2
RESET
U1
ADG2128YCP
VSS
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AGND
R27
R26
R25
R24
R23
R22
C28 +
0.1UF
R8
R9
1
2
1
2
1
2
3
4
3
4
3
4
AVDD
X6_X7-A
X6_X7-B
X8_X9-A
X8_X9-B
X10_X11-A
X10_X11-B
C29
10UF
16V
2K2
2K2
K3
K2
K1
RESET
C24 +
0.1UF
R31
C25
10UF
6V3
10K
10K
10K
R29
R30
10K
R28
T5
T4
VL
AVSS
AGND
AVDD
SDA
SCL
DGND
SDA
SCL
5VUSB
+
C1
0.1UF
D1
0.1UF
C30
+
C26 +
0.1UF
C2
16V
10UF
AVDD
C31
6V3
10UF
C27
6V3
10UF
VL
AVSS
AGND
AVDD
+3.3V
K5
K4
J2-4
J2-3
J2-2
J2-1
EVAL-ADG2128EBZ User Guide
UG-341
05769-006
EVAL-ADG2128EBZ User Guide
05769-007
UG-341
05769-008
Figure 9. Component Placement Drawing
Figure 10. Component Side Printed Circuit Board (PCB) Drawing
Rev. C | Page 10 of 13
UG-341
05769-009
EVAL-ADG2128EBZ User Guide
Figure 11. Solder Side PCB Drawing
4
70
69
2
3
2
5
1
4
5
2
3
29
30
31
32
34
33
35
36
37
39
38
40
41
42
30
29
31
32
33
35
34
36
37
38
40
39
41
42
2
1
4
5
1
4
15
17
20
19
21
68
67
16
66
65
18
64
63
23
25
26
62
61
22
60
59
27
16
15
18
58
57
24
70
69
28
68
67
19
21
22
66
65
17
64
63
23
26
25
27
28
62
61
20
60
59
24
58
57
3
1
43
45
44
47
49
46
48
51
50
53
52
55
54
43
45
56
44
47
46
49
48
51
50
53
52
14
13
12
11
9
10
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
5
4
3
2
1
3
5
55
54
56
4
1
2
2
1
2
2
1
1
2
1
3
4
5
2
2
5
3
2
3
1
1
3
1
4
2
1
2
1
1
2
1
2
5
4
1
2
2
1
1
1
2
1
1
2
2
1
1
1
2
2
1
1
2
2
1
2
2
2
1
1
1
5
4
1
2
1
1
2
2
3
2
1
42
2
71
322
12
01
91
81
2
5
6
6
5
7
2
4
8
3
9
2
2
1
0
3
1133
0
2
3
9
23456781
1
1
2
2
1
2
1
1
1
1
1
1
1
655
5
45
35
25
15
04
94
84
74
64
544
34
1
2
2
1
3
0
4
4
9
5
8
3
6
7
7
6
8
5
3
9
4
0
1
57
2
3
21
1
3
1
0
3
4
9
51
61
71
81
92
02
122
32
42
52
62
72
82
1
2
8 SHIELD
2
1
2
2
2
2
1
1
2
1
2
2
2
2
2
1
4
1
1
2
2
2
2
1
7
2
8
1
1
2
1
1
1
2
1
2
1
2
2
1
1
1
2
2
3
3
2
1
2
5
1
2
1
1
3
2
1
3
2
1
2
1
4
2
5
3
05769-010
2
4
2
3
5
1
2
4
4
3
4
3
1
1
5
2
8
1
2
4
7
1
1
3
3
4
6
1
2
A
5
2
1
2
1
2
K
1
1
1
2
1
2
2
1
3
2
4
1
2
1
2
1
1
6
1
1
2
5
2
2
7
2
1
9
2
5
1
4
2
2
3
Figure 12. Composite Side PCB Drawing
Rev. C | Page 11 of 13
UG-341
EVAL-ADG2128EBZ User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 4.
Qty.
19
2
3
4
2
1
Reference Designator
C1, C3, C5 to C9, C11, C15, C16,
C18 to C22, C24, C26, C28, C30
C2, C29
C4, C13, C14
C12, C25, C27, C31
C10, C17
C23
1
1
1
4
5
20
2
1
2
1
1
4
1
5
1
1
1
1
20
2
1
D1
D4
J1
J2
K1 to K5
R1 to R4, R12 to R27
R5, R6
R7
R8, R9
R10
R11
R28 to R31
RESET
T1 to T5
U1
U2
U3
U5
X0 to X11, Y0 to Y7
SCL, SDA
XTAL1
Description
0.1 μF (0603 package), 50 V, X7R, SMD, ceramic capacitor
Supplier/Number
FEC 4765837
10 μF, TAJ_B, 16 V, SMD, tantalum capacitor
10 μF (0805 package), X5R, ceramic capacitor
10 μF, TAJ_A, 6.3 V, SMD, tantalum capacitor
22 pF (0603 package), 50 V, X7R, SMD, ceramic capacitor
2.2 μF (0603 package), 6.3 V, X5R, SMD, ceramic
capacitor
Diode, SOT-23
LED (0805 package)
USB mini-B connector
4-pin terminal block
SIP-2P, 2-pin header and shorting shunt
SMD, resistor (0603 package)
75 Ω, SMD, resistor (0603 package)
0 Ω, SMD, resistor (0603 package)
2.2 kΩ, SMD, resistor (0603 package)
10 kΩ, SMD, resistor (0603 package)
1 kΩ, SMD, resistor (0603 Package)
10 kΩ, SMD, resistor (0603 package)
Push-button switch (sealed 6 mm × 8 mm)
Test point
8 × 12 analog switch array
64k I2C serial EEPROM
USB microcontroller
3.3 V regulator
Socket, phono, PCB, gold, one pair
50 Ω, straight, SMB jack
24 MHz, CM309S SMD crystal
FEC 498-737
Digi-Key 490-1709-1-ND
FEC 197-130
FEC 722-005
Digi-Key 490-1552-1-ND
Rev. C | Page 12 of 13
FEC 984-3728
FEC 5790852
FEC 9786490 (Digi-Key WM17116CT-ND)
FEC 151-791
FEC 511-705 and FEC 150-411
Not inserted
FEC 933-1549
FEC 933-1662
FEC 933-0810
FEC 933-0399
FEC 933-0380
FEC 933-0399
FEC 177-807
Not inserted
Analog Devices, Inc., ADG2128YCPZ
Digi-Key 24LC64-I/SN-ND
Digi-Key 428-1669-ND
Analog Devices, Inc., ADP3303ARZ-3.3
FEC 382-4834
FEC 1111349
FEC 950-9658
EVAL-ADG2128EBZ User Guide
UG-341
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2006–2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG05769-0-10/15(C)
Rev. C | Page 13 of 13