EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluating the ADF5901 24 GHz Voltage Controlled Oscillator (VCO) and
Programmable Gain Amplifier (PGA) with a 2-Channel Power Amplifier (PA) Output
FEATURES
GENERAL DESCRIPTION
Contains ADF5901 24 GHz VCO and PGA with a 2-channel
PA output
Contains ADF4159 13 GHz fractional-N frequency synthesizer
Accompanying software allows control of the ADF5901 and
the ADF4159 functions from a PC
The EV-ADF5901SD2Z evaluation board allows the user
to evaluate the performance of the ADF5901 24 GHz VCO
and PGA with a 2-channel PA output. Figure 1 shows the
EV-ADF5901SD2Z, which contains the ADF5901, the ADF4159,
three high frequency, K-type SMA connectors for the local
oscillator (LO) output and two transceiver (Tx) outputs, two
high frequency SMA connectors for the AUX and the AUX
outputs, banana connectors for power supply, and a connector
for the serial interface.
EVALUATION KIT CONTENTS
EV-ADF5901SD2Z evaluation board
ADDITIONAL EQUIPMENT
PC running Windows® XP or more recent version
Analog Devices, Inc., EVAL-SDP-CS1Z system demonstration
platform serial (SDP-S) board
Spectrum analyzer
Oscilloscope (optional)
5 V power supply
The EV-ADF5901SD2Z evaluation kit also contains software
that is compatible with Windows XP and later versions to allow
easy programming of the device.
The EV-ADF5901SD2Z evaluation board requires an EVALSDP-CS1Z (SDP-S) controller board, which is not supplied with
the kit. The EVAL-SDP-CS1Z allows software programming of
the ADF5901 device.
DOCUMENTS NEEDED
ADF5901 data sheet
Full specifications on the ADF5901 are available in the ADF5901
data sheet, which should be consulted in conjunction with this
user guide when working with the evaluation board.
REQUIRED SOFTWARE
Analog Devices ADF5901 software
13381-001
EV-ADF5901SD2Z EVALUATION BOARD PICTURE
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1 Input Signals...................................................................................3 Evaluation Kit Contents ................................................................... 1 Output Signals ...............................................................................3 Additional Equipment ..................................................................... 1 Default Operation .........................................................................3 Documents Needed .......................................................................... 1 Evaluation Board Quick Start Procedures .....................................4 Required Software ............................................................................ 1 EV-ADF5901SD2Z Control Software.........................................4 General Description ......................................................................... 1 Evaluation and Testing......................................................................8 EV-ADF5901SD2Z Evaluation Board Picture .............................. 1 Evaluation Board Schematics and Artwork ...................................9 Revision History ............................................................................... 2 Ordering Information .................................................................... 17 Evaluation Board Hardware ............................................................ 3 Bill of Materials ........................................................................... 17 Power Supplies .............................................................................. 3 Related Links ............................................................................... 18 REVISION HISTORY
12/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
EVALUATION BOARD HARDWARE
The EV-ADF5901SD2Z evaluation board requires the use of an
EVAL-SDP-CS1Z (SDP-S) controller board to program the
device. The EVAL-SDP-CS1Z is not included and must be
purchased separately. The EV-ADF5901SD2Z schematics are
shown in Figure 7 to Figure 14. The EV-ADF5901SD2Z
evaluation board layout is shown in Figure 15 and Figure 16.
POWER SUPPLIES
The EV-ADF5901SD2Z board is powered via a 5 V external
supply that must be connected as described in the Evaluation
Board Quick Start Procedures section.
INPUT SIGNALS
Control VTUNE from the ADF4159. Alternatively, control VTUNE
externally via J7 by removing R20 and powering down the
ADF4159.
OUTPUT SIGNALS
The Tx and LO outputs from the ADF5901 contain dc bias
voltage and are available on the J8 (TXOUT1), J9 (TXOUT2)
and J4 (LOOUT) output SMAs.
DEFAULT OPERATION
All the necessary components to operate the ADF5901 are
included on the EV-ADF5901SD2Z.
The 100 MHz temperature controlled crystal oscillator (TCXO)
provides the necessary reference signal. An external REFIN can
be used, if desired.
Rev. 0 | Page 3 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
EVALUATION BOARD QUICK START PROCEDURES
Take the following steps to evaluate the ADF5901:
EV-ADF5901SD2Z CONTROL SOFTWARE
1.
The control software for the EV-ADF5901SD2Z accompanies
the EV-ADF5901SD2Z on a CD. For software installation
procedures, follow the on-screen instructions.
To run the EV-ADF5901SD2Z control software, take the
following steps:
1.
Choose the ADF5901 and ADF4159 file on the desktop or
in the Start menu.
2.
Within the Select Device and Connection tab, choose
your device and your connection method, and click
Connect.
3.
Confirm that Analog Devices Eval Board connected
displays at the bottom left of the window. Otherwise, the
software has no connection to the EV-ADF5901SD2Z
evaluation board.
Note that when connecting the EV-ADF5901SD2Z, it takes
approximately 5 sec to 10 sec for the status label to change.
13381-002
Connect the power supply to the EV-ADF5901SD2Z:
a. 5 V to the Banana Connector P3
b. GND to the Banana Connector P2.
2. Install the ADF5901 software by following the on-screen
instructions.
3. Connect the EVAL-SDP-CS1Z controller board to the PC
and to the EV-ADF5901SD2Z.
4. Install the hardware driver; follow the on-screen instructions.
5. Run the ADF5901 software.
6. Choose ADF5901 and ADF4159 and SDP board (black)
in the Select Device and Connection tab of the software
front panel window (see Figure 2).
7. Ensure that a SDP board connected message appears on
the front panel (see Figure 2).
8. Connect an ac-coupled signal source analyzer to the TX2
output SMA, J9.
9. Click the ADF5901 Controls tab and click Write All
Registers (see Figure 4).
10. Click the ADF5901 Controls tab and click Initialize
ADF5901 (see Figure 3).
11. Measure the result on TXOUT2 (J9).
Figure 2. Software Front Panel Display—Select Device and Connection
Rev. 0 | Page 4 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
To control the ADF5901 settings (see Figure 3), select the
ADF5901 Controls tab.
Use the register section within the ADF5901 Controls tab to
select from the general options available for the ADF5901,
including calibration control and register read back.
At initial power-up of the device, click Initialize ADF5901 to
perform the initialization sequence as described in the ADF5901
data sheet.
Following the sequence, the ADF5901 powers up, and all the
ADF5901 blocks calibrate.
13381-003
To set the calibration frequency for the ADF5901, go to the RF
Settings section shown in Figure 3 under the ADF5901 Controls
tab. Set the frequency to the center of the frequency band. Type
the desired output frequency in the VCO Frequency text box
(in MHz).
UG-864
Figure 3. Software Front Panel Display—ADF5901 Controls
Rev. 0 | Page 5 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
To control the ADF4159 settings (see Figure 4), select the
ADF4159 Controls tab.
Use the Muxout drop-down box within the Main Controls tab
to choose the signal connected to the output of the MUXOUT pin.
Click the button under each register value within the Main
Controls tab to write that value to the device. The register values
are shown in Figure 4 at the bottom of the window. When the
background of a register value is green, this indicates that the
value was changed and needs to be written to the device.
13381-004
Within the ADF4159 Controls tab, select the Main Controls tab
to set the RF Settings and PLL Settings. In the RF Settings
area, set the RF VCO Output Frequency to half the ADF5901
VCO output. In addition, set the Reference Frequency the
same as the applied reference signal. Calculate the PFD
frequency from the reference frequency, the R counter, the
reference doubler, and the reference divide by 2. Ensure that the
value in the PFD Frequency box matches the value specified in
the loop filter design.
In the PLL Settings area, program the Charge Pump Setting to
the value for which the loop filter was designed. Program the
Phase Detector Polarity to negative when using an inverting
active loop filter configuration. (Note that a passive loop filter
was used on this evaluation board).
Figure 4. Software Front Panel Display—ADF4159 Controls
Rev. 0 | Page 6 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
To configure the ramp functionality of the ADF4159, select the
Ramps and Shift Keying tab.
To select the ramp type, go to the Ramp mode drop-down box
within the Ramps and Shift Keying tab, and set the various
ramp parameters in the CLK1 box and Up Ramp boxes.
Example
ADF5901 Tx output with a ramp time of 5 ms. For 200 MHz,
the PLL is programmed for a 100 MHz ramp because the
EV-ADF5901SD2Z uses the ADF5901 auxilary output with a
12 GHz output signal. After each parameter is set in the
software, it must be written to the device.
To configure the other options in the Ramps and Shift Keying
tab, set the various Ramp and Shift Keying controls of the
ADF4159.
13381-005
Figure 5 shows the ramping settings for an example of a continuous
triangular ramp of 1000 up ramp steps over 200 MHz at the
UG-864
Figure 5. Software Front Panel Display—ADF4159 Ramps and Shift Keying
Rev. 0 | Page 7 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
EVALUATION AND TESTING
To evaluate and test the performance of the ADF5901, take the
following steps:
2.
1.
3.
Follow the on-screen instructions to install the ADF5901
evaluation software.
Connect the EVAL-SDP-CS1Z controller board to the
EV-ADF5901SD2Z.
Connect dc blocked J9 (TXOUT2) to the spectrum
analyzer.
Click the ADF5901 icon to run the ADF5901 software.
5.
6.
7.
Select the USB board and the ADF5901 device in the
Select Device and Connection tab of the software front
panel window (see Figure 2).
In the ADF4159 Main Controls tab, click Write All Registers
to power up the ADF4159.
In the ADF5901 Controls tab, click Initialize ADF5901 to
power up and calibrate the ADF5901. See Figure 6 for the
suggested setup.
Measure the TXOUT2 output signal on the J9 SMA.
+5V
POWER
SUPPLY
SDP-S
ADAPTOR
BOARD
SPECTRUM
ANALYZER
PC
13381-006
1.
4.
BLOCKING CAPACITOR
Figure 6. Typical EV-ADF5901SD2Z Evaluation Board Setup
Rev. 0 | Page 8 of 18
Figure 7. EV-ADF5901SD2Z Schematic (Page 1)
Rev. 0 | Page 9 of 18
GPIO0
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
AUXB
AUX
SDP
SPI_CLK
SPI_MISO
SPI_MOSI
SDP
REFIN
R4 0
TP16
1
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_CLK
SPI_MOSI
SPI_MISO
RFINA
RFINB
REFIN
CE
CLK
DATA
LE
TXDATA
DVDD
R7 0
VP
AVDD
R5 0
CP
AGND
TP17
1
AGND
SPI SIGNALS
CLK_PLL
DATA_PLL
LE_PLL
CE_PLL
TX_DATA
MUXOUT_PLL
CLK_TX
DATA_TX
LE_TX
DOUT_TX
CE_TX
CPOUT
MUXOUT_PLL
CLK_TX
SPI_CLK
DATA_TX
SPI_MOSI
LE_TX
SPI_MISO
DOUT_TX
GPIO0
CE_TX
GPIO1
GPIO2
SPI_CON
CLK_PLL
GPIO3
DATA_PLL
GPIO4
LE_PLL
GPIO5
CE_PLL
GPIO6
TX_DATA
GPIO7
MUXOUT_PLL
ADF4159
ADF4159_PLL
MUXOUT
AVDD_TX
CE_PLL
CLK_PLL
DATA_PLL
LE_PLL
TX_DATA
DVDD_PLL
TP3
CPOUT
571-0500
571-0100
P3
P2
142-0701-851
AGND
1
REF_IN
VSUPPLY
AGND
LOOP FILTER
CPOUT LFP VTUNE
J1
AGND
142-0701-851
TP18
DNI
AGND
AVDD_TX
AVDD_PLL
DVDD_PLL
AGND
VTUNE
REFIN
CE_TX
CLK_TX
DATA_TX
LE_TX
REFERENCE
REFIN
AVDD
REF_CLK REF
POWER MANAGEMENT
POWER
VSUPPLY
AVDD_PLL
VTUNE
TBD0603
TBD0603
C42
DNI
C37
TBD1206
C33
DNI
TP20
REFIN
AVDD_TX
AVDD_PLL
DVDD_PLL
VTUNE
REFIN
CE
CLK
DATA
LE
AVDD_TX
0
J7
0
R8
LO_OUT
AUX
AUXB
ADF5901
ATEST
MUXOUT
DOUT
ADF5901_TXTX_OUT1
TX_OUT2
AHI
R9
TX_AHI
DVDD_PLL
TP4
AVDD_TX
TP5
DVDD_PLL
TP22
R3
R10 0
VCO_AHI
AVDD_PLL
TP23
AUX
AUXB
LO
MUX_TX 1
DOUT_TX
TP24
ATEST_TX
TX_OUT1
TX_OUT2
1
AGND
AGND
5 4 3 2
J9
AGND
AGND
J4
1
AGND
3 2
LO OUTPUT
02K243-40M
LO
TX OUTPUTS
02K243-40M
TX_OUT2
1
5 4 3 2
J8
02K243-40M
TX_OUT1
J3
J2
AUX OUTPUTS
142-0761-801
AUXB
142-0761-801
AUX
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
EVALUATION BOARD SCHEMATICS AND ARTWORK
TP21
13381-007
0
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
J5
AGND
OUT GPIO0
GPIO2
OUT
GPIO4
OUT
OUT
GPIO6
AGND
R36
R6
100K
TBD0603
FX8-120S-SV(21)
R35
100K
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
DNI
8
U3
A0 VCC
EEPROM
A1
5
A2
SDA
SCL
WP
VSS
4
24LC32A-I/MS
VIO
1
2
3
6
7
AGND
OUT
OUT
OUT
SPI_MOSI
SPI_MISO
SPI_CLK
GPIO1
OUT
GPIO3
OUT GPIO5
OUT
GPIO7
OUT
FX8-120S-SV(21)
Figure 8. EV-ADF5901SD2Z Schematic (Page 2)
Rev. 0 | Page 10 of 18
13381-008
J5
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
DNI
R19
R20
TBD0805
0
DNI
OUT
TBD0805
C14
TBD0805
C13
VTUNE
13381-009
TBD0805
R18
DNI
C12
TBD0805
DNI
DNI
CPOUT
IN
AGND
Figure 9. EV-ADF5901SD2Z Schematic (Page 3)
0
600OHM
Y1
4
1 E/D VDDOUT 3
GND
2
CWX823-100.0MHZ
1
R43
91
REF
OUT
AGND
TBD0603
DNI
R42
10PF
AGND
IN
REFIN
R45
0
Figure 10. EV-ADF5901SD2Z Schematic (Page 4)
Rev. 0 | Page 11 of 18
13381-010
C41
22UF
C40
10K
TP36
R41
1
E1
2
R40
AVDD
IO
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
TP32
1
OUT
1UF
C36
0
R27
C32
AVDD_TX
0
AGND
TP34
U4
1
0
R29
3
5
1
R2
AVDD_PLL
EN VOUT
0
NC GND
4
2
ADP150AUJZ-3.3-R7
C38
C34
0
VIN
OUT
1UF
R25
AGND
TP35
U5
0
3
1
DVDD_PLL
R32
5
VOUT
EN
0
NC GND
4
2
ADP150AUJZ-3.3-R7
OUT
AGND
Figure 11. EV-ADF5901SD2Z Schematic (Page 5)
Rev. 0 | Page 12 of 18
13381-011
R30
0
VIN
1UF
1
C39
R26
C35
C
D1
1N4001
MBR0540T1G
1
VOUT
2
SENSE
3
GND
4
NC
PAD
PAD
ADP7104
8
VIN
7
PG
6
GND
5
EN
0
1UF
C
R33
1UF
A
R23
1UF
VSUPPLY
A
IN
U6
D2
EV-ADF5901SD2Z Evaluation Board User Guide
AHI
TP30
1
AGND
AGND
10PF
DNI
TBD0402
C30
DNI
VREG
TBD0402
C25
C23
0.22UF
DNI
TBD0402
C20
0.047UF
1
C2
C28
1
TP31
0.22UF
TP29
C31
AGND
AGND
AGND
C1
1000PF
0.1UF
C29
C27
10PF
C26
1000PF
VCO_AHI
0.1UF
C24
C22
10PF
C21
C15
0.1UF
C18
1000PF
TX_AHI
C16
UG-864
AGND
R22
5.1K
AGND
C2
C1
VCO_AHI
IO
VTUNE
IN
AUXB
OUT
AUX
OUT
RSET
MUXOUT
OUT
PAD
32
31
30
29
28
27
26
25
AGND
AGND
OUT
TX_AHI
DOUT
LE
DATA
CLK
CE
AGND
VREG
AHI
OUT
IN
IN
IN
IN
IN
IN
IN
1000PF
IO
C2
C1
1000PF
AGND
Figure 12. EV-ADF5901SD2Z Schematic (Page 6)
Rev. 0 | Page 13 of 18
13381-012
REFIN
R21
IN
OUT
OUT
ATEST
AGND
LO_OUT
AGND
AGND
AHI
9
10
11
12
13
14
15
AHI 16
OUT
24
23
22
21
20
19
18
17
5901
TBD0603
IO
AGND 1
TX_OUT1 2
AGND 3
4
5
AGND 6
TX_OUT2 7
AGND 8
U101
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
TP6
SPI_CLK
CLK_PLL
R11
OUT
IN
OUT
330
R51
TP7
OUT
SPI_MOSI R47
R52
GPIO0
LE_PLL
0
IN
LE_TX
R48
OUT
390
R53
330
10K
OUT
R37
R56
TP11
AGND
AGND
AVDD_TX
TP1
IO
OUT
390
R38
330
GPIO2
IN
R49
10K
TX_DATA
R14
R54
GPIO3
IN
AGND
330
IN
GPIO5
OUT
TP8
R13
TP15
DATA_TX
330
390
R34
IN
AGND
GPIO6
0
TP13
DATA_PLL
330
IN
R55
10K
SPI_MOSI R12
IN
AGND
AGND
IN
GPIO4
CLK_TX
R46
390
R28
330
10K
SPI_CLK
IN
TP14
TP10
TP12
CE_TX
OUT
330
AGND
TP9
IO
DVDD_PLL
10K
R39
IN
DOUT_TX R50
SPI_MISO
0
OUT
TP2
GPIO7
IN
CE_PLL
R15
OUT
390
R44
330
AGND
IN
MUXOUT_PLLR24
0
13381-013
TP19
GPIO1
OUT
Figure 13. EV-ADF5901SD2Z Schematic (Page 7)
Rev. 0 | Page 14 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
AGND
10PF
C11
1000PF
0.1UF
C9
10PF
C8
9
IO
IO
DVDD
REFIN
21
SW2
20
SW1
C19
24
CP
17
MUXOUT
OUT
IN
IN
IN
IN
IN
IN
IN
RFINA
RFINB
CE
TXDATA
CLK
DATA
LE
5
RFINA
4
RFINB
13
CE
12
TXDATA
14
CLK
15
DATA
16
LE
MUXOUT
AGND
Figure 14. EV-ADF5901SD2Z Schematic (Page 8)
Rev. 0 | Page 15 of 18
OUT
ADF4159CCPZ
13381-014
AGND
CP
1000PF
2
3
1
10
11
PAD
R16
TBD0603
IN
1000PF
RSET
SDVDD
DVDD
VP
23
U2
CPGND
DGND
SDGND
EPAD
C17
R17
5.1K
AGND
REFIN
DNI
AGND
AVDD
8
7
6
18
19
22
AVDD
IO
AGND
VP
1000PF
C7
0.1UF
C6
10PF
C5
AGND
C10
VP
DVDD
1000PF
C4
0.1UF
C3
AVDD
UG-864
13381-015
EV-ADF5901SD2Z Evaluation Board User Guide
Figure 15. EV-ADF5901SD2Z Layer 1 (Component Side)
13381-016
UG-864
Figure 16. EV-ADF5901SD2Z Layer 4 (Bottom Plane)
Rev. 0 | Page 16 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Quantity
4
6
6
6
1
1
1
6
1
1
1
1
1
1
1
1
2
2
3
1
1
1
11
13
Part Description
1 nF, 0603 capacitors
1 nF, 0402 capacitors
10 pF, 0402 capacitors
100 nF, 0603 capacitors
47 nF, 0402 capacitor
220 nF, 0402 capacitor
220 nF, 0603 capacitor
1 µF, 0805 capacitors
22 µF, 0805 capacitor
10 pF, 0603 capacitor
220 pF, 0805 capacitor
3.3 nF, 0805 capacitor
100 pF, 0805 capacitor
Diode, standard, 1 A, 50 V
Diode, Schottky, 0.5 A, 20 V
Ferrite bead
CONN-PCB end launch jack
CONN-PCB high frequency SMA
CONN-PCB SMA RA jack
CONN-PCB vertical type RCPT SMD
CONN-PCB single SKT black
CONN-PCB single SKT red
0 Ω, 0402 resistors
0 Ω, 0603 resistors
Manufacturer
AVX
AVX
AVX
AVX
Kemet
Taiyo Yuden
AVX
AVX
Murata
AVX
Multicomp
Kemet
Multicomp
Multicomp
ON Semiconductor
Wuerth Elektronik
Emerson
Emerson (Johnson)
Rosenberger
Hirose
Deltron
Deltron
Multicomp
Multicomp
Part Number
06035A102JAT2A
04023C102KAT2A
04023A100JAT2A
06033C104JAT2A
C0402C473K3RACTU
JMK105B7224KV-F
06033C224KAT2A
08053C105KAZ2A
GRM21BE70G226ME51L
06035A100JAT2A
MCCA001042
C0805C332J5GACTU
MCCA001040
1N4001
MBR0520LT1G
7427-92642
142-0701-851
142-0761-801
02K243-40M
FX8-120S-SV(21)
571-0100
571-0500
MC 0.0625W 0402 1% 0R
MC 0.063W 0603 0R
9
2
1
5
2
Reference Designator
C1, C2, C17, C19
C4, C7, C10, C18, C24, C29
C5, C8, C11, C21, C26, C31
C3, C6, C9, C15, C22, C27
C16
C23
C28
C32, C34 to C36, C38, C39
C40
C41
C12
C13
C14
D1
D2
E1
J1, J7
J2, J3
J4, J8, J9
J5
P2
P3
R1, R2, R23, R25 to R27, R29 to R33
R3 to R5, R7 to R10, R24, R40, R45,
R50, R55, R56
R11 to R15, R46 to R49
R17, R22
R20
R28, R34, R37, R38, R44
R35, R36
330 Ω, 0603 resistors
5.1 kΩ, 0603 resistors
0 Ω, 0805 resistor
390 Ω, 0603 resistors
100 kΩ ,0603 resistor
Multicomp
Multicomp
Multicomp
Multicomp
Multicomp
1
1
1
1
1
R41
R43
R18
R19
U2
Multicomp
Multicomp
Multicomp
Multicomp
Analog Devices, Inc.
1
2
2
1
1
1
2
1
U3
U4
U5
U6
Y1
U101
TP16, TP17
TP23
10 kΩ, 0603 resistor
91 Ω, 0603 resistor
510 Ω, 0805 resistor
1 kΩ, 0805 resistor
ADF4159 13 GHz Fractional-N
frequency synthesizer
IC 32 Kbit serial EEPROM
3.0 V CMOS linear regulator
1.8 V CMOS linear regulator
3.3 V CMOS linear regulator
100 MHz crystal clock oscillator
ADF5901 24 GHz TX MMIC
Black test point
Red test point
MC 0.063W 0603 330R
MC 0.063W 0603 5k1
MC 0.1W 0805 0R
MC 0.063W 0603 390R
MC 0.063W 0603 5%
100K
MC 0.063W 0603 10K
MC 0.063W 0603 1% 91R
MC 0.1W 0805 1% 510R
MC 0.1W 0805 1% 1K
ADF4159CCPZ
Microchip
Analog Devices
Analog Devices
Analog Devices
Connor-Winfield
Analog Devices
Vero
Vero
24LC32A-I/MS
ADP150AUJZ-3.0
ADP150AUJZ-1.8
ADP7104ARDZ-3.3
CWX113-100.0M
ADF5901WCCPZ-U6
20-2137
20-313137
Rev. 0 | Page 17 of 18
UG-864
Quantity
3
1
2
4
5
28
EV-ADF5901SD2Z Evaluation Board User Guide
4
2
Reference Designator
C20, C25, C30
C33
C37, C42
R6, R16, R21, R42
R39, R51 to R54
TP1 to TP15, TP18 to TP22, TP24, TP29
to TP32, TP34 to TP36
C1, C2, C17, C19
SCREW1, SCREW2
2
NUT1, NUT2
Part Description
Do not install
Do not install
Do not install
Do not install
Do not install
Do not install
Manufacturer
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Part Number
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
1 nF, 0603 capacitors
Screw, cheese, nylon, M3X10,
PK100
Nut/washer, nylon, M3, PK100
AVX
ALLTHREAD Plastics
Limited
DURATOOL
06035A102JAT2A
119030010
1140030
RELATED LINKS
Resource
ADF5901
ADF4159
ADP7104
Description
Product Page, 24 GHz VCO and PGA with 2-Channel PA Output
Product Page, Direct Modulation/Fast Waveform Generating, 13 GHz, Fractional-N Frequency Synthesizer
Product Page, 20 V, 500 mA, Low Noise, CMOS LDO
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG13381-0-12/15(0)
Rev. 0 | Page 18 of 18