Summit-ICE Emulator
Hardware and Software
Installation Guide
Edition: Revision 4, December 2002
Part Number
MANSUMICE
Analog Devices, Inc.
Digital Signal Processing Division
One Technology Way
Norwood, MA 02062-9106
a
Notice
Analog Devices, Inc. reserves the right to make changes to or to discontinue any product or
service identified in this publication without notice.
Analog Devices assumes no liability for Analog Devices applications assistance, customer
product design, customer software performance, or infringement of patents or services described
herein. In addition, Analog Devices shall not be held liable for special, collateral, incidental or
consequential damages in connection with or arising out of the furnishing, performance, or use of
this product.
Analog Devices products are not intended for use in life-support applications, devices, or
systems. Use of an Analog Devices product in such applications without the written consent of
the appropriate Analog Devices officer is prohibited.
Users are restricted from copying, modifying, distributing, reverse engineering and reverse
assembling or reverse compiling the Analog Devices Summit-ICE PCI-based emulator
operational software (one copy may be made for back-up purposes only).
No part of this document may be reproduced in any form without permission.
Trademark and Service Mark Notice
The Analog Devices logo, SHARC, the SHARC logo, TigerSHARC, the TigerSHARC logo, and
EZ-ICE are registered trademarks. VisualDSP++, the VisualDSP++ logo, Blackfin, the Blackfin
logo, CROSSCORE, the CROSSCORE logo, EZ-KIT Lite, ICEPAC, and The DSP Collaborative
are trademarks of Analog Devices, Inc. Microsoft and Windows are registered trademarks, and
Windows NT is a trademark of Microsoft Corporation. All other brand and product names are
trademarks or service marks of their respective owners.
Limited Warranty
The Summit-ICE hardware is warranted against defects in materials and workmanship for a
period of one year from the date of purchase from Analog Devices or from an authorized dealer.
The Summit-ICE PCI-based emulator contains ESD (electrostatic
discharge) sensitive devices.
Electrostatic charges readily
accumulate on the human body and equipment and can discharge
without detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD precautions are
recommended to avoid performance degradation or loss of
functionality. Store used Summit-ICE PCI-based emulator in the
protective-shipping package.
ii
Summit-ICE PCI-based Emulator Manual
Table of Contents
1
INTRODUCTION.......................................................................................................................................... 1-1
1.1
1.2
1.3
1.4
1.5
1.6
2
FOR MORE INFORMATION ABOUT ANALOG DEVICES PRODUCTS ................................................................. 1-1
FOR TECHNICAL OR CUSTOMER SUPPORT .................................................................................................... 1-1
PURPOSE OF THIS MANUAL .......................................................................................................................... 1-2
INTENDED AUDIENCE ................................................................................................................................... 1-2
MANUAL CONTENTS .................................................................................................................................... 1-2
ON-LINE HELP .............................................................................................................................................. 1-3
GETTING STARTED ................................................................................................................................... 2-1
2.1 OVERVIEW ................................................................................................................................................... 2-1
2.2 CONTENTS OF YOUR SUMMIT-ICE PACKAGE ............................................................................................... 2-1
2.3 PC CONFIGURATION .................................................................................................................................... 2-1
2.4 INSTALLATION TASKS .................................................................................................................................. 2-2
2.4.1
Install the Summit-ICE Hardware ..................................................................................................... 2-2
2.4.1.1 Unpacking the Emulator ................................................................................................................................2-2
2.4.1.2 Installing the Summit-ICE Board in your Computer......................................................................................2-2
2.4.1.3 Configuring the Summit-ICE Pod..................................................................................................................2-3
2.4.1.3.1
Connecting to a 5V Target...................................................................................................................2-3
2.4.1.3.2
Connecting to a 3V Target...................................................................................................................2-4
2.4.1.3.3
Reducing Noise Issues on the JTAG Signals.......................................................................................2-4
2.5 CONNECTING THE POD TO THE SUMMIT-ICE BOARD ................................................................................ 2-5
2.6 CONNECTING THE POD TO YOUR TARGET SYSTEM ................................................................................... 2-5
2.7 INSTALLING THE SUMMIT-ICE PCI DRIVER ................................................................................................ 2-5
2.7.1
Windows 98 PCI Driver Installation ................................................................................................. 2-5
2.7.2
Windows NT PCI Driver Installation .............................................................................................. 2-10
2.7.3
Windows 2000 PCI Driver Installation ........................................................................................... 2-10
2.7.4
Windows XP PCI Driver Installation .............................................................................................. 2-13
2.7.5
Verifying Driver Installation ........................................................................................................... 2-16
2.7.6
Creating a New Platform................................................................................................................. 2-20
2.7.6.1
2.7.6.2
3
SUPPORT....................................................................................................................................................... 3-1
3.1
3.2
4
Creating a new platform based on an Analog Devices Evaluation Kit......................................................... 2-20
Creating a New Platform from Scratch ........................................................................................................ 2-23
TECHNICAL SUPPORT ................................................................................................................................... 3-1
QUALITY ASSURANCE .................................................................................................................................. 3-1
REFERENCES............................................................................................................................................... 4-1
INDEX .......................................................................................................................................................................... I
iii
Summit-ICE PCI-based Emulator Manual
List of Tables
TABLE 2-1: MINIMUM PC CONFIGURATION ............................................................................................................... 2-2
List of Figures
FIGURE 2-1 JUMPERS .................................................................................................................................................. 2-3
FIGURE 2-2 LEDS ...................................................................................................................................................... 2-3
FIGURE 2-3 TERMINATORS CONNECTED TO THE JTAG SIGNALS ................................................................................ 2-4
FIGURE 2-4: ADD NEW HARDWARE WIZARD DIALOG BOX ....................................................................................... 2-6
FIGURE 2-5: SEARCH FOR THE DRIVER ....................................................................................................................... 2-6
FIGURE 2-6: SEARCH THE CD-ROM .......................................................................................................................... 2-7
FIGURE 2-7: THE DRIVER IS LOCATED ....................................................................................................................... 2-7
FIGURE 2-8: SEARCH FOR .SYS FILE DIALOG BOX ...................................................................................................... 2-8
FIGURE 2-9: OPEN THE .SYS FILE................................................................................................................................ 2-8
FIGURE 2-10: COPYING FILES..................................................................................................................................... 2-9
FIGURE 2-11: FINISH THE SOFTWARE INSTALLATION ................................................................................................. 2-9
FIGURE 2-12: FOUND NEW HARDWARE WIZARD ..................................................................................................... 2-10
FIGURE 2-13: SEARCH FOR A SUITABLE DRIVER ...................................................................................................... 2-11
FIGURE 2-14: LOCATE DRIVER FILES ....................................................................................................................... 2-11
FIGURE 2-15: DRIVER FILE SEARCH RESULTS .......................................................................................................... 2-12
FIGURE 2-16: COMPLETING DRIVER INSTALLATION DIALOG BOX ........................................................................... 2-13
FIGURE 2-17: FOUND NEW HARDWARE WIZARD ..................................................................................................... 2-14
FIGURE 2-18: SEARCH FOR A SUITABLE DRIVER ...................................................................................................... 2-15
FIGURE 2-19: COMPLETING DRIVER INSTALLATION DIALOG BOX ........................................................................... 2-16
FIGURE 2-20: VERIFIYING DRIVER INSTALLATION ................................................................................................... 2-17
FIGURE 2-21: ICETEST UTILITY................................................................................................................................ 2-17
FIGURE 2-22: DETECTED EMULATORS ..................................................................................................................... 2-18
FIGURE 2-23: ICETEST PASS..................................................................................................................................... 2-19
FIGURE 2-24 ICETEST FAILURE ................................................................................................................................ 2-20
FIGURE 2-25: VISUALDSP++ CONFIGURATOR (FROM TEMPLATE)........................................................................... 2-21
FIGURE 2-26: PLATFORM PROPERTIES (FROM TEMPLATE) ........................................................................................ 2-21
FIGURE 2-27: VISUALDSP++ CONFIGURATOR (FROM TEMPLATE) PLATFORM ADDED ............................................ 2-22
FIGURE 2-28: PLATFORM PROPERTIES (FROM SCRATCH).......................................................................................... 2-23
FIGURE 2-29: DETECTED EMULATORS ..................................................................................................................... 2-24
FIGURE 2-30: DEVICE PROPERTIES ........................................................................................................................... 2-24
FIGURE 2-31: PLATFORM PROPERTIES (FROM SCRATCH) DEVICE ADDED ................................................................ 2-25
FIGURE 2-32: VISUALDSP++ CONFIGURATOR (FROM SCRATCH) PLATFORM ADDED .............................................. 2-25
iv
Summit-ICE PCI-based Emulator Manual
1 Introduction
Thank you for purchasing Analog Devices Summit-ICE PCI-based JTAG emulator. The SummitICE is used in conjunction with the VisualDSP++ development environment to create, test and
debug advanced DSP application software on all of Analog devices fixed and floating-point
JTAG based DSPs.
The Summit-ICE system provides state-of-the-art support for JTAG-compliant Analog Devices
DSPs. Key features of the Summit-ICE include:
•
•
•
•
1.1
Plug-n-Play PCI card
Windows 98, Windows NT, Windows 2000, or Windows XP operation
Emulation for the industry standard Analog Devices JTAG families of DSPs
Rugged high-speed JTAG emulation pod
For More Information About Analog Devices Products
Analog Devices can be accessed on the Internet at http://www.analog.com. You can directly
access the DSP Web pages at http://www.analog.com/dsp. This page provides access to DSP
specific technical information and documentation, product overviews, and product
announcements.
For
specific
information
about
DSP
tools,
go
to
http://www.analog.com/dsp/tools.
You may also obtain additional information about Analog Devices and its products in any of the
following ways:
1.2
•
FAX questions or requests for information to (781) 461-3010.
•
Access the Computer Products Division File Transfer Protocol (FTP) site at
ftp://ftp.analogdevices.com/ or ftp://137.71.25.69 or ftp://ftp.analog.com.
For Technical or Customer Support
You can reach our Customer Support group in the following ways:
•
•
E-mail DSP Tools questions to: dsptools.support@analog.com
DSP Tools Tech Support Form:
http://www.analog.com/industry/dsp/tools/form_techsupport.html
•
E-mail general DSP questions to:
dsp.support@analog.com
1-1
Summit-ICE PCI-based Emulator Manual
dsp.europe@analog.com (European customer support)
•
•
1.3
Call: (800) ANALOGD
Contact your local Analog Devices sales office or an authorized Analog Devices
distributor.
Purpose of This Manual
The Summit-ICE Hardware and Software Installation Guide provides directions for installing the
hardware and software for the Summit-ICE on your PC. This manual also provides a description
of the use and configuration of the components on the Summit-ICE PCI-based emulator.
1.4
Intended Audience
This manual is an installation guide for the Summit-ICE PCI-based emulator. This manual is
intended to help the customer quickly install the Summit-ICE so that they can begin using
VisualDSP++.
1.5
Manual Contents
This manual contains the following information:
•
Chapter 1 — Introduction
Provides manual information and Analog Devices contact information.
•
Chapter 2— Getting Started
Provides software and hardware installation procedures, PC system requirements,
and basic board information.
•
Chapter 3 — Support
Provides Technical Support Contact information.
•
Chapter 4 — References
Provides information on different resources available in developing an ADI DSP
application.
1-2
Summit-ICE PCI-based Emulator Manual
1.6
On-line Help
Your software installation kit includes online Help as part of the Windows interface. These
Help files provide information about VisualDSP++ and the Summit-ICE.
To view the VisualDSP++’s Help, click on the Help menu item or go to the Windows task bar
and select Start\Programs\VisualDSP\VisualDSP++ Help.
The documents in the following two tables can be found through online help or in the Docs folder
of your VisualDSP++ installation.
For more documentation, please go to http://www.analog.com/dsp/tech_doc.
1-3
Summit-ICE PCI-based Emulator Manual
2 Getting Started
2.1
Overview
This chapter provides the information you need to begin using the Summit-ICE system. Install
your software and hardware in the order presented in section 2.4 for correct operation. This
chapter has the following sections:
2.2
•
Contents of your Summit-ICE Package (Section 2.2)
Provides a list of the components that are shipped with this Summit-ICE PCIbased Emulator.
•
PC Configuration (Section 2.3)
Describes the minimal requirement for the PC to work with the Summit-ICE
PCI-based Emulator.
•
Installation Tasks (Section 2.4)
Describes the step-by-step procedure for setting up the hardware and software.
Contents of your Summit-ICE Package
Your Summit-ICE PCI-based emulator package contains the following items:
•
•
•
•
Summit-ICE JTAG daughter card
Summit-ICE pod assembly
CD containing emulation driver software
Registration card – please fill out and return
The Summit-ICE PCI-based emulator contains ESD
(electrostatic discharge) sensitive devices. Electrostatic charges
readily accumulate on the human body and equipment and can
discharge without detection. Permanent damage may occur on
devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation
or loss of functionality. Store used Summit-ICE in the
protective-shipping package.
2.3
PC Configuration
For correct operation of the Summit-ICE PCI-based emulator, your computer must have the
minimal configuration shown in Table 2-1.
Summit-ICE PCI-based Emulator Manual
2-1
Table 2-1: Minimum PC Configuration
Windows 98, Windows NT, Windows 2000, or Windows XP
Intel (or compatible) 166 MHz processor
VGA monitor and color video card
2-button mouse
50 MB free on hard drive
32 MB RAM
One available PCI slot
CD-ROM drive
2.4
Installation Tasks
The following tasks are provided for the safe and effective use of the Summit-ICE PCI-based
emulator. Follow these instructions in the order presented to ensure correct operation of your
software and hardware.
1. Install the Summit-ICE hardware
2. Install the Summit-ICE driver
3. Verify driver installation.
2.4.1 Install the Summit-ICE Hardware
This section provides all of the information required to install the Summit-ICE card and pod into
your PC.
The Summit-ICE PCI-based emulator contains ESD
(electrostatic discharge) sensitive devices. Electrostatic charges
readily accumulate on the human body and equipment and can
discharge without detection. Permanent damage may occur on
devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation
or loss of functionality. Store used Summit-ICE in the
protective-shipping package.
2.4.1.1 Unpacking the Emulator
Remove the Summit-ICE board and pod from the package. Care should be taken when
handling these boards to avoid discharge of static electricity, which may damage some
components. Put the pod aside. The Summit-ICE board must first be installed in your
computer.
2.4.1.2 Installing the Summit-ICE Board in your Computer
For specific instructions on installing a PCI card into your computer consult the documentation
that is provided by the manufacturer of your computer.
2-2
Summit-ICE PCI-based Emulator Manual
Upon installing your Summit-ICE you will need to install the driver before you can use it for
the first time. Refer to section 2.7 for instructions on how to install the appropriate driver.
2.4.1.3 Configuring the Summit-ICE Pod
The Summit-ICE pod contains four internal jumpers. These jumpers are accessed by removing
the four screws on the bottom of the plastic enclosure and removing the top of the enclosure. The
jumpers are shown in Figure 2-1. The Summit-ICE pod also contains two status LEDs. The LED
on the left is for voltage status (3V/5V) and the LED on the right is for emulator status. The
LEDs are shown in Figure 2-2. Periodic LED activity on the emulator status LED indicates
communication between the target DSPs and emulator.
Figure 2-1 Jumpers
Figure 2-2 LEDs
2.4.1.3.1 Connecting to a 5V Target
Jumper J1 is used to differentiate between a 3V or 5V target. This is the only jumper that most
users will need to change. When the jumper is installed the JTAG signals are configured to
connect to a 5V target. When the jumper is installed the LED on the left side is not illuminated.
2-3
Summit-ICE PCI-based Emulator Manual
2.4.1.3.2 Connecting to a 3V Target
When the jumper is not installed the JTAG signals are configured to connect to a 3V target.
When the jumper is not installed the LED on the left is illuminated indicating a 3V target. This is
the default setting.
2.4.1.3.3 Reducing Noise Issues on the JTAG Signals
There are three jumpers provided to help reduce problems that may arise because of ringing and
reflections on the JTAG signals on the target board. The default is that these jumpers are not
installed. The three jumpers are J2, J3, and J4.
Jumpers J2 and J3 are used for adding a parallel terminator on the TDO and CLKIN signals.
When the jumper is installed a parallel terminator of 120Ω and 91Ω is connected to the TDO and
CLKIN signals. Figure 2-3 shows how the terminator is connected to the JTAG signals. It is
important to note that the target MUST be able to drive a 51Ω load before these jumpers are
installed. The DSP cannot drive this load directly; a driver should be inserted between the JTAG
signals on the DSP and the JTAG signals on the header.
Figure 2-3 Terminators connected to the JTAG Signals
Jumper J4 is provided to allow the board level test pins on the JTAG connector (BTMS, BTCK,
BTRST, and BTDI) to be used as ground pins to allow for greater shielding on the JTAG cable
connecting the pod to the target. These pins should only be used as ground pins if they are not
used on your target.
2-4
Summit-ICE PCI-based Emulator Manual
2.5
Connecting the Pod to the Summit-ICE Board
The pod connects to the Summit-ICE board through a shielded flat ribbon cable and a 25-pin
connector. Connect the pod to the Summit-ICE before applying power to the PC. The JTAG
header attached to the pod can be connected/disconnected without damaging the pod system as
long as the target system is powered down.
Important! Connect/disconnect the remote pod to/from the emulator card
only with the power turned off. Failure to follow this precaution may
result in damage to the pod or board.
)
2.6
Connecting the Pod to your Target System
The pod connects to the target processor through the JTAG interface. The target board must be
built with an appropriate JTAG connector. Please note the position of the key pin. The key pin
should be used as a guide to connect the pod to the target. Included with the Summit- ICE system
are two extender connectors. These extenders are used to connect the Summit-ICE system to a
target, which was designed for use with the ADI ICEPAC™. These extenders allow connection
to the JTAG pins on the ICEPAC header.
2.7
Installing the Summit-ICE PCI Driver
The Summit-ICE can be installed on Windows 98, Windows NT, Windows 2000, and Windows
XP and requires one available PCI slot. Section 2.7.1 describes the installation on Windows 98.
Section 2.7.2 describes the installation on Windows NT. Section 2.7.3 describes the installation
on Windows 2000. Section 2.7.4 describes the installation on Windows XP.
2.7.1 Windows 98 PCI Driver Installation
Before using the Summit-ICE for the first time, the Windows 98 PCI driver must be installed.
This is accomplished as follows:
2-5
Summit-ICE PCI-based Emulator Manual
1. Insert the VisualDSP++ Emulator Tools CD-ROM into the CD-ROM drive.
2. Power on the PC and start Windows 98. This will activate the Windows 98 Add New
Hardware Wizard as shown in Figure 2-4.
Figure 2-4: Add New Hardware Wizard Dialog Box
3. Click Next.
4. Select Search for the best driver for your device as shown in Figure 2-5.
Figure 2-5: Search for the Driver
2-6
Summit-ICE PCI-based Emulator Manual
5. Click Next.
6. Select CD-ROM drive as shown in Figure 2-6.
Figure 2-6: Search the CD-ROM
7. Click Next.
Windows 98 will locate the PCIEmul.inf file that is on the CD-ROM as shown in Figure 2-7.
Figure 2-7: The Driver is Located
2-7
Summit-ICE PCI-based Emulator Manual
8. Click Next.
Figure 2-8 will appear.
Figure 2-8: Search for .sys File Dialog Box
9. Click Browse button.
Figure 2-9 will appear.
Figure 2-9: Open the .sys File
10. In Drives select your CD-ROM drive.
11. Click OK.
Figure 2-10 will appear.
2-8
Summit-ICE PCI-based Emulator Manual
Figure 2-10: Copying Files
12. Click OK.
The driver installation is now complete as shown in Figure 2-11.
Figure 2-11: Finish the Software Installation
13. Click Finish to exit the wizard.
Verify driver installation by following the instructions in Section 2.7.5.
2-9
Summit-ICE PCI-based Emulator Manual
2.7.2 Windows NT PCI Driver Installation
Before using the Summit-ICE for the first time, run the Emulator Tools installation and be sure to
select Summit/Mountain as the Emulator to install. The install will place the driver in the
appropriate folder so that the driver is installed properly.
2.7.3 Windows 2000 PCI Driver Installation
Before using the Summit-ICE for the first time, the Windows 2000 PCI driver must be installed.
This is accomplished as follows:
1. Insert the VisualDSP++ Emulator Tools CD-ROM into the CD-ROM drive.
2. Power on the PC and start Windows 2000. This will activate the Windows 2000 Found
New Hardware Wizard as shown in Figure 2-12.
Figure 2-12: Found New Hardware Wizard
2-10
Summit-ICE PCI-based Emulator Manual
3. Click Next.
4. Select Search for a suitable driver for my device as shown in Figure 2-13.
Figure 2-13: Search for a Suitable Driver
5. Click Next.
6. Ensure that CD-ROM drive is selected as shown in Figure 2-14.
Figure 2-14: Locate Driver Files
2-11
Summit-ICE PCI-based Emulator Manual
7. Click Next.
Figure 2-15 appears.
Figure 2-15: Driver File Search Results
2-12
Summit-ICE PCI-based Emulator Manual
8. Click Next.
Windows 2000 will automatically install the Summit-ICE JTAG Emulator driver. The driver
installation is now complete as shown in Figure 2-16.
Figure 2-16: Completing Driver Installation Dialog Box
9. Click Finish to exit the wizard.
Verify driver installation by following the instructions in section 2.7.5.
2.7.4 Windows XP PCI Driver Installation
Before using the Summit-ICE for the first time, the Windows XP PCI driver must be installed.
This is accomplished as follows:
2-13
Summit-ICE PCI-based Emulator Manual
1. Insert the VisualDSP++ Emulator Tools CD-ROM into the CD-ROM drive.
2. Power on the PC and start Windows XP. This will activate the Windows XP Found
New Hardware Wizard as shown in Figure 2-17.
Figure 2-17: Found New Hardware Wizard
3. Select Install from a list or specific location.
4. Click Next.
2-14
Summit-ICE PCI-based Emulator Manual
5. Select Search for the best driver in these locations and select Include this location in
the search as shown in Figure 2-18. Enter the path for the drive that contains
VisualDSP++ Emulator Tools CD-ROM.
Figure 2-18: Search for a Suitable Driver
6. Click Next.
2-15
Summit-ICE PCI-based Emulator Manual
7. Windows XP will automatically install the Summit-ICE JTAG Emulator driver. The
driver installation is now complete as shown in Figure 2-19.
Figure 2-19: Completing Driver Installation Dialog Box
8. Click Finish to exit the wizard.
Verify driver installation by following the instructions in Section 2.7.5.
2.7.5 Verifying Driver Installation
Before using your Summit-ICE PCI-based emulator, verify that the PCI driver software is
installed properly.
2-16
Summit-ICE PCI-based Emulator Manual
1. Open Device Manager and verify that Summit-ICE JTAG Emulator shows under DSP
Emulators with no exclamation point as shown in Figure 2-20.
Figure 2-20: Verifiying Driver Installation
2. From Start\Program Files\VisualDSP\ICE Test Utility open IceTest as shown in
Figure 2-21 to verify that the driver is installed correctly and that there is connectivity
with the target board.
Figure 2-21: IceTest Utility
2-17
Summit-ICE PCI-based Emulator Manual
3. If there is more than one emulator installed in the PC click on the browse button (“…”)
to the right of Type as shown in Figure 2-21 to bring up the list of Emulators installed as
shown in Figure 2-22. If there is only one emulator installed in the PC then the address
information will be filled in automatically when launching IceTest and you can skip to
step 5.
Figure 2-22: Detected Emulators
2-18
Summit-ICE PCI-based Emulator Manual
4. Choose Summit-ICE as shown in Figure 2-22 and click OK. This will fill in Base
Address with the appropriate address as shown in Figure 2-21.
5. Ensure that the JTAG header is connected to a target board and click Start.
6. If all the tests pass, green check marks appear next to the entries in the Status group as
shown in Figure 2-23.
Figure 2-23: IceTest Pass
The driver is installed correctly and communication with the target board has been
established.
If they do not pass you will see a note at the bottom of the dialog box explaining the failure in
more detail as show in Figure 2-24.
2-19
Summit-ICE PCI-based Emulator Manual
Figure 2-24 IceTest Failure
2.7.6 Creating a New Platform
When creating a new platform, use an existing template or create a new template from scratch.
Base your platform on one of the existing platforms (Analog Devices evaluation kits) listed in the
VisualDSP++ Configurator window’s Platform Templates box. To launch the VisualDSP++
Configurator go to Start\Program Files\VisualDSP\VisualDSP++ Configurator.
2.7.6.1 Creating a new platform based on an Analog Devices Evaluation Kit
To create a platform that is based on an Analog Devices, Inc. evaluation kit follow theses
instructions:
¾ NOTE: The Addresses shown are for example purposes only. Actual addresses will
depend on the PC and operating system.
2-20
Summit-ICE PCI-based Emulator Manual
1. Bring up the VisualDSP++ Configurator from the Windows Start menu.
2. In the Platform Templates box, highlight the template on which to base your new platform
as shown in Figure 2-25.
Figure 2-25: VisualDSP++ Configurator (from template)
3. Click Copy and Figure 2-26 will appear.
Figure 2-26: Platform Properties (from template)
2-21
Summit-ICE PCI-based Emulator Manual
4. If required, you can add a new device by following steps 9 and 10 in section 2.7.6.2 or click
OK to add your new platform as shown in Figure 2-27.
Figure 2-27: VisualDSP++ Configurator (from template) Platform Added
2-22
Summit-ICE PCI-based Emulator Manual
5. Click OK to finish the VisualDSP++ Configurator
2.7.6.2 Creating a New Platform from Scratch
Follow the instructions below to create a platform that is not based on an Analog Devices
evaluation kit.
1. Bring up the VisualDSP++ Configurator from the Windows Start menu.
2. Click New in the VisualDSP++ Configurator to open the Platform Properties dialog box as
shown in Figure 2-28 to create a new platform.
Figure 2-28: Platform Properties (from scratch)
2-23
Summit-ICE PCI-based Emulator Manual
3. In the name field, type an appropriate name for the platform that is being created.
The Type field indicates the type of emulator that you would like to use.
4. If there is more than one emulator installed in the PC click on the browse button (“…”) to the
right of Type as shown in Figure 2-28 to bring up the list of Emulators installed shown in
Figure 2-29. If there is only one emulator installed in the PC then the address information
will be filled in automatically when launching IceTest and you can skip to step 6.
Figure 2-29: Detected Emulators
5. Highlight the emulator to be used for your platform and click OK.
Notice that the Emulator Settings group shown in Figure 2-28 gets filled in with the correct
information based on the emulator you chose.
6. Highlight Device 0 in the Devices list and click Modify to display the Device Properties
dialog box shown in Figure 2-30.
Figure 2-30: Device Properties
2-24
Summit-ICE PCI-based Emulator Manual
7. Select an appropriate name for your device and then select the type of device to which you
will be connecting.
8. Click OK and you will see that your device shows up under the Devices list with the
appropriate type as shown in Figure 2-31.
Figure 2-31: Platform Properties (from scratch) Device Added
9. Click OK to add your new platform as shown in Figure 2-32.
Figure 2-32: VisualDSP++ Configurator (from scratch) Platform Added
10. Click OK to finish the VisualDSP++ Configurator.
2-25
Summit-ICE PCI-based Emulator Manual
3 Support
3.1
Technical Support
For technical support, you may contact the Analog Devices DSP Tools Technical Support group
in any of the following ways:
•
•
•
Fill out the DSP Tools Technical Support Web site form at:
http://forms.analog.com/Form_Pages/DSP/tools/contactDSP.asp
Send a description of the problem by e-mail to:
dsptools.support@analog.com
Call the customer support hotline at 1-800-ANALOG-D (1-800-262-5643 U.S.A. only)
For direct support of the Analog Devices’ DSPs, call the Analog Devices’ DSP Applications
Engineering group at 1-800-ANALOG-D or email dsp.support@analog.com.
3.2
Quality Assurance
Analog Devices is committed to providing quality products and services. To continually provide
this quality, please contact our Quality Assurance Department directly if you have any concerns
(603) 883-2430, Monday through Friday during normal business hours or via e-mail at
dsptools@analog.com. Our Quality Assurance Manager will listen to your concerns and provide
a timely and effective solution.
3-1
Summit-ICE PCI-based Emulator Manual
4 References
This section describes other documentation resources you may find helpful in developing your
application.
•
•
•
•
•
•
For information on designing the interface between an Analog Devices JTAG DSP and
the emulation header on your custom DSP target board, refer to the latest version of
Analog Devices EE-68.
For information on the architecture and system interface of the ADSP processor, refer to
the appropriate Analog Devices DSP Hardware Reference.
For ADSP timing specification and other hardware design information, refer to the
appropriate DSP Data Sheet.
For complete information on software development tools (assembler, compiler, linker,
and so on), refer to the documentation included with VisualDSP++. This information is
available in printed manuals, online help, and online in PDF format.
For information about your development platform, refer to your operating system
manuals and hardware system manuals.
For information about digital signal processing theory and applications, you may wish to
consult:
• Higgins. Digital Signal Processing In VLSI. Prentice-Hall, 1990.
• Oppenheim and Schafer. Digital Signal Processing. Prentice-Hall, 1975.
Summit-ICE PCI-based Emulator Manual
4-1
Index
3
L
3V ..............................................................iii, 2-3, 2-4
LED ................................................................ 2-3, 2-4
5
N
5V ..................................................................... iii, 2-3
New platform.................. 2-20, 2-21, 2-22, 2-23, 2-25
C
P
Configurator ..........2-17, 2-20, 2-21, 2-22, 2-23, 2-25
Customer Support.................................................. 1-1
PC Configuration................................................... 2-1
PCI.... ii, 1-1, 1-2, 2-1, 2-2, 2-3, 2-5, 2-10, 2-13, 2-16
Pod.................................................................. 2-1, 2-4
Properties................................. 2-21, 2-23, 2-24, 2-25
D
Daughter Card ....................................................... 2-1
Documents............................................................. 1-3
Driver….2-1, 2-2, 2-3, 2-5, 2-6, 2-7, 2-9, 2-10, 2-11,
2-13, 2-15, 2-16, 2-17, 2-19
Q
Quality Assurance ................................................. 3-1
Questions ............................................................... 1-1
E
R
Electrostatic ................................................ii, 2-1, 2-2
References ............................................................. 4-1
Registration Card................................................... 2-1
H
Hardware ....................i, 1-2, 2-2, 2-6, 2-10, 2-14, 4-1
Help, On-line ......................................................... 1-3
I
IceTest Utility...................................................... 2-17
Installation…..i, 1-2, 2-1, 2-2, 2-5, 2-10, 2-13, 2-16,
2-17
S
Software.................................. 1-2, 2-1, 2-2, 2-16, 4-1
Status ................................................................... 2-19
T
Technical Support........................................... 1-2, 3-1
Test ...................................................................... 2-17
J
V
JTAG .........................1-1, 2-1, 2-13, 2-16, 2-17, 2-19
Jumpers........................................................... 2-3, 2-4
VisualDSP++…ii, 1-1, 1-2, 1-3, 2-6, 2-10, 2-14, 215, 2-20, 2-21, 2-22, 2-23, 2-25, 4-1
Help .................................................................. 1-3
I
Summit-ICE PCI-based Emulator Manual