ADV3224-EVALZ/ADV3225-EVALZ/ADV3228EVALZ/ADV3229-EVALZ User Guide UG-766 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluation Board for the ADV3224/ADV3225/ADV3228/ADV3229 Analog Crosspoint Switch FEATURES GENERAL DESCRIPTION Full featured evaluation board for the ADV3224/ADV3225/ADV3228/ADV3229 On-board USB port for inputs and outputs control ±5 V operation The ADV3224/ADV3225 are high speed, 16 × 8 analog crosspoint switch matrices, and the ADV3228/ADV3229 are 8 × 8, analog crosspoint switch matrices. These devices offer a −3 dB signal bandwidth of greater than 750 MHz and a high slew rate of greater than 2500 V/µs. EVALUATION KIT CONTENTS ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ ADV3229-EVALZ evaluation board Instruction guide for software download EQUIPMENT NEEDED Signal source or video pattern generator and signal analyzer Power supplies (5 V/1 A and ±5 V/1 A) PC running Windows XP only Type A to Type B USB 2.0 connector (recommended) BNC-to-BNC connector for inputs and outputs SOFTWARE NEEDED ADV3224/ADV3225 Control Software for 16 × 8 switch array ADV3228/ADV3229 Control Software for 8 × 8 switch array The ADV3224/ADV3225/ADV3228/ADV3229 include eight independent output buffers that can be placed into a high impedance state for paralleling crosspoint outputs to prevent off channels from loading the output bus. The ADV3224 and ADV3228 have a gain of 1, and the ADV3225 and ADV3229 have a gain of 2, and all of the devices operate on voltage supplies of ±5 V. Channel switching is performed via a serial digital control that accommodates the daisy chaining of several devices, or via a parallel control to allow updating of an individual output without reprogramming the entire array. The ADV3224/ADV3225/ADV3228/ADV3229 are available in a 72-lead LFCSP package over the extended industrial temperature range of −40°C to +85°C. Applications of these analog crosspoint switches include routing high speed video signals (NTSC, PAL, SECAM, YUV, RGB, MPEG, and wavelet), data communications, and telecommunications. This user guide provides all of the supporting documents and software for the evaluation of the ADV3224/ADV3225/ADV3228/ ADV3229. Full specifications on these products are available in the ADV3224/ADV3225 and ADV3228/ADV3229 data sheets, which should be consulted in conjunction with this user guide when working with the evaluation board. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 11 UG-766 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Analog Inputs.................................................................................4 Evaluation Kit Contents ................................................................... 1 Analog Outputs .............................................................................4 Equipment Needed ........................................................................... 1 Thru Cal .........................................................................................4 Software Needed ............................................................................... 1 Evaluation Board Control Software ................................................5 General Description ......................................................................... 1 Installing the Evaluation Software ..............................................5 Revision History ............................................................................... 2 Evaluation Board Schematics and Artwork ...................................6 Evaluation Board Photograph and Functional Block Diagram ........ 3 Ordering Information .................................................................... 10 Evaluation Board Hardware.............................................................. 4 Bill of Materials ........................................................................... 10 Power Supply ................................................................................. 4 REVISION HISTORY 11/14—Revision 0: Initial Version Rev. 0 | Page 2 of 11 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide UG-766 EVALUATION BOARD PHOTOGRAPH AND FUNCTIONAL BLOCK DIAGRAM SER/PAR D0 D1 D2 D3 D4 A0 A1 A2 CLK 40-BIT SHIFT REGISTER WITH 4-BIT PARALLEL LOADING DATAIN UPDATE 40 PARALLEL LATCH 40 DECODE 8 × 5:16 DECODERS 128 12707-001 SWITCH MATRIX OUTPUT BUFFER G = +1, G = +2 8 OUTPUTS ADV3224/ ADV3225 SET INDIVIDUAL OR RESET ALL OUTPUTS TO OFF 8 ENABLE/DISABLE CE RESET 16 INPUTS DATAOUT Figure 1. Rev. 0 | Page 3 of 11 UG-766 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide EVALUATION BOARD HARDWARE The ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ ADV3229-EVALZ evaluation boards allow the user to easily evaluate the ADV3224/ADV3225/ADV3228/ADV3229 in their various modes and configurations. Figure 2 shows the typical bench setup used to evaluate the four analog crosspoint switches. POWER SUPPLY These evaluation boards require a typical ±5 V power supply for the analog circuitry and a 5 V single supply for the digital circuitry. Connect the supplies as shown in Figure 2. ANALOG OUTPUTS The eight outputs of each evaluation board are terminated with 75 Ω. All eight outputs can be disabled simultaneously using the RESET button. The waveform signal from each or from all of the outputs can be checked using a signal analyzer such as an oscilloscope or television. THRU CAL ANALOG INPUTS Drive any or all of the inputs, IN00 to IN07, with a waveform generator, video pattern generator, or any signal source that can provide an input voltage between −3 V and +3 V for the ADV3224/ADV3228, and between −1.5 V and +1.5 V for the ADV3225/ADV3229. All the inputs are terminated with 75 Ω. Printed circuit board (PCB) traces contribute certain errors in the system such as crosstalk, impedance mismatch, and reflection. To remove these errors, these evaluation boards use a response calibration method that uses a thru. This thru cal method is used primarily in network analyzers to compare the trace between J25 and J26, which is the reference and is shown in Figure 2, to the PCB traces from and to the device under test (DUT). If errors or mismatch are measured, they are corrected by the network analyzer. ANALOG INPUTS WAVEFORM/SIGNAL GENERATOR OSCILLOSCOPE ANALOG OUTPUTS ANALOG INPUTS TELEVISION VIDEO PATTERN GENERATOR DC POWER SUPPLY DC POWER SUPPLY –5V GND GND +5V +5V PC CONTROL THRU CAL 12707-002 TYPE A TO TYPE B USB Figure 2. Typical Evaluation Setup Rev. 0 | Page 4 of 11 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide UG-766 EVALUATION BOARD CONTROL SOFTWARE These evaluation boards are configured with a USB friendly interface to allow programmability of the ADV3224/ADV3225/ ADV3228/ADV3229 registers. Parallel and serial programming, using the P1 and P3 connectors on the evaluation board, can also be achieved. For information on these two programming modes, refer to the ADV3224/ADV3225 and ADV3228/ADV3229 data sheets. Note that the software can be installed in other operating systems, such as Windows 7 or Windows 8; however, any commands by the user in the GUI are not read and a dialog box appears as shown in Figure 3. The same dialog box appears when the software is activated but the USB connector is not connected to the evaluation board. INSTALLING THE EVALUATION SOFTWARE 2. Download the appropriate control software, the ADV3224/ADV3225 Control Software or the ADV3228/ADV3229 Control Software. Extract the .zip file and open or run the .exe file. The graphic user interface (GUI) for the ADV3224/ADV3225 and ADV3228/ADV3229 appear as shown in Figure 4. By default, all inputs and outputs are disabled, although an input signal is present in the input port of the evaluation board. Figure 3. Error Message 12707-004 1. 12707-003 The following instructions describe the procedure to install evaluation the software onto a PC running the Windows® XP operating system only. Figure 4. GUI Window for ADV3224/ADV3225 (Left) and GUI Window for ADV3228/ADV3229 (Right) Rev. 0 | Page 5 of 11 R1 Rev. 0 | Page 6 of 11 DOUT C1 0.1µF AGND 2kΩ VUSB 0Ω R7 0Ω R6 0Ω R5 0Ω R4 0Ω R3 0Ω R2 AGND C2 AGND AGND .01µF BERG69157-102 1 2 P2 RESETB CEB CLK UPDATEB A0 A1 A2 A3 D0 D1 D2 D3 D4 OSC1 ICRST NC NC NC NC NC NC NC NC NC 1000pF 7 28 1000pF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 3M3314-2002 AGND R8 A3 AGND 2kΩ A C CMD67-21VGC/TR8 (GREEN) CR1 R9 0.47µF C7 Figure 5. Serial, Parallel, and USB Interface Circuitry on the Evaluation Board AGND Y1 22pF 20.000MHZ 22pF 2 3 OSC2 C9 1 4 1MΩ AGND C8 OSC1 R10 NC CR2 2kΩ NC A C D+ CMD67-21VGC/TR8 (GREEN) DNC NC NC OSC2 ICPGD ICPGC A0 A1 A2 A3 D0 D1 D2 D3 D4 PIC18F4550-I/PT 37 27 26 25 5 4 3 2 41 40 39 38 1 44 43 42 36 35 32 31 13 12 U1 AGND 18 MCLR/VPP/RE3 VDD1 VDD2 VUSB 17 RE2/AN7/OESPP RB7/KBI3/PGD 16 RE1/AN6/CK2SPP RB6/KBI2/PGC 15 RE0/AN5/CK1SPP RB5/KBI1/PGM 14 RD7/SPP7/P1D RB4/AN11/KBI0/CSSPP 11 RD6/SPP6/P1C RB3/AN9/CCP2/VPO 10 RD5/SPP5/P1B RB2/AN8/INT2/VMO 9 RD4/SPP4 RB1/AN10/INT1/SCK/SCL 8 RD3/SPP3 RB0/AN12/INT0/FLT0/SDI/SDA 24 RD2/SPP2 RA5/AN4/SS/HLVDIN/C2OUT 23 RD1/SPP1 RA4/T0CKI/C1OUT/RCV 22 RD0/SPP0 RA3/AN3/VREF+ 21 RC7/RX/DT/SDO RA2/AN2/VREF-/CVREF 20 RC6/TX/CK RA1/AN1 19 RC5/D+/VP RA0/AN0 30 RC4/D-/VM OSC1/CLKI 33 RC2/CCP1/P1A NC/ICRST/ICVPP 34 RC1/T1OSI/CCP2/UOE NC/ICPORTS RC0/T1OSO/T13CKI OSC2/CLKO/RA6 NC/ICDT/ICPGD NC/ICCK/ICPGC VSS1 VSS2 6 29 AGND1 1 P1 AGND C6 C4 C5 0.1µF VUSB 0.1µF C3 VUSB RED ICPGD ICPGC ICRST VUSB AGND AGND PLACE NEAR USB CONNECTOR C10 10µF VUSB AGND 1 4 5 P4 4-1734376-8 AGND 1 2 3 4 5 6 2 3 6 DD+ AGND P3 PIN1 DESIGNATOR SAMTECTSW10608GS6PIN VUSB CMD67-21VGC/TR8 (GREEN) PLACE NEAR OTHER LEDS 2kΩ VUSB AGND C DIN UPDATEB CEB CLK RESETB TP11SH9CBE RESET 1 3 1 R11 A P 1 CR3 N PLACE BETWEEN ADJACENT VDD/VSS PINS 12707-005 UG-766 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide EVALUATION BOARD SCHEMATICS AND ARTWORK 1 1 1 1 1 1 1 J8 1 2 1 AVEE_B 108-0740-001 1 AVCC_B 108-0740-001 AGND 2 3 4 5 1 AGND 2 3 4 5 J7 AGND 2 3 4 5 J6 AGND 2 3 4 5 2 J5 BERG69157-102 P5 AGND 2 3 4 5 J4 AGND 2 3 4 5 J3 AGND 2 3 4 5 J2 AGND 3 4 5 J1 1 1 1 AVEE AVCC AVEE DVCC AVCC DVCC AGND R14 75Ω J9 1 1 AGND J11 1 RN3 3 6 22Ω AGND R18 75Ω AGND 1 1 AGND 2 3 4 5 J14 1 R22 75Ω 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PAD RN3 8 1 22Ω AGND R21 75Ω AGND AVCC IN08 AVEE IN09 AVCC IN10 AVEE IN11 AVCC IN12 AVEE IN13 AVCC IN14 AVEE IN15 AGND AVEE AGND R20 75Ω RN3 7 2 22Ω AGND R19 75Ω AGND 2 3 4 5 J16 AGND 2 3 4 5 J15 AGND 2 3 4 5 RN3 4 5 22Ω AGND R17 75Ω 2 3 4 5 J10 AGND R16 75Ω 2 3 4 5 AGND R15 75Ω JUMPER P5 - TIES AVCC AND DVCC 1 DVCC_B 108-0740-001 AGND R13 75Ω AGND 2 3 4 5 J13 1 AGND 2 3 4 5 J12 1 AGND AGND R25 75Ω AGND AGND IN07 AVEE IN06 AVCC IN05 AVEE IN04 AVCC IN03 AVEE IN02 AVCC IN01 AVEE IN00 AGND DVCC GEN_QFN72_10X10_PAD7_7X7_7 DUT PAD 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 AVCC OUT07 AVEE OUT06 AVCC OUT05 AVEE OUT04 AVCC OUT03 AVEE OUT02 AVCC OUT01 AVEE OUT00 AVCC AVEE J18 J17 R28 75Ω 1 AGND 5 4 3 2 1 AGND 5 4 3 2 AGND AGND 1 D1 D2 AGND 5 4 3 2 1 22Ω 1 J24 AGND 1 1 P6 1 2 AGND BERG69157-102 UPDATB SERB D3 D4 1 DIN J23 5 4 3 2 D0 1 RN2 8 A2 1 5 4 3 2 RN2 2 7 22Ω 1 J22 A1 1 A0 1 RESETB CEB DOUT CLK AGND 5 4 3 2 1 J20 5 4 3 2 1 AGND J21 RN2 3 6 22Ω 1 J19 5 4 3 2 54 AGND 53 RESETB 52 CEB 51 DOUT 50 CLK 49 DIN 48 UPDATEB 47 SERB 46 A0 45 A1 44 A2 43 D0 42 D1 41 D2 40 D3 39 D4 38 AGND 37 DVCC U2 RN2 5 4 22Ω R26 75Ω R27 75Ω 1 R23 75Ω 1 AGND 1 AGND 1 R24 75Ω 1 AGND 1 Rev. 0 | Page 7 of 11 AGND_B 108-0740-001 1 1 Figure 6. DUT Schematic on the Evaluation Board C11 .01UF AGND AGND R12 10kΩ DVCC RESETB CEB DOUT CLK DIN UPDATEB SERB A0 A1 A2 D0 D1 D2 D3 D4 JUMPER P6 - FOR SETTING SERIAL OR PARALLEL MODE 1 1 AGND ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide UG-766 12707-006 C14 Rev. 0 | Page 8 of 11 Figure 7. Decoupling Network on the Evaluation Board C13 AVCC AVCC 0.01µF C16 1000pF C17 C12 10 X 1000pF CAPS BETWEEN AVCC AND AGND 10 X 00.01µF CAPS BETWEEN AVCC AND AGND 10 X 0.1µF CAPS BETWEEN AVCCC AND AGND 0.1µF C21 0.1µF C24 0.1µF C27 0.1µF C30 0.1µF C33 0.1µF C36 AGND AGND AGND 0.1µF C39 0.1µF AVEE AVEE AVEE 0.1µF C45 0.1µF C48 10 X 00.01µF CAPS BETWEEN AVEE AND AGND 0.1µF C51 0.1µF C54 0.1µF C57 0.1µF C60 0.1µF C63 10 X 0.1µF CAPS BETWEEN AVEE AND AGND 10 X 1000pF CAPS BETWEEN AVEE AND AGND DECOUPLING NETWORK 0.1µF C66 AGND AGND AGND 0.1µF C69 0.1µF AVCC 4 X 00.01µF CAPS BETWEEN DVCC AND AGND DVCC 3 X 1000pF CAPS BETWEEN AVCC AND AVEE AVCC C72 0.01µF C75 0.01µF C78 AVEE 0.01µF 3 X 00.01µF CAPS BETWEEN AVCC AND AVEE 1000pF 0.1µF C15 0.1µF C18 0.01µF C22 0.01µF C25 0.01µF C28 0.01µF C31 0.01µF C34 0.01µF C37 0.01µF C40 0.01µF C42 C43 0.01µF C46 1000pF C47 0.01µF C52 0.01µF C55 0.01µF C58 0.01µF C61 0.01µF C64 0.01µF C67 0.01µF C70 0.01µF C73 1000pF C76 1000pF C79 AVEE AVCC 0.01µF C19 1000pF C20 1000pF C23 1000pF C26 1000pF C29 1000pF C32 1000pF C35 1000pF C38 1000pF C41 1000pF C44 0.01µF C49 1000pF C50 1000pF C53 1000pF C56 1000pF C59 1000pF C62 1000pF C65 1000pF C68 1000pF C71 1000pF C74 0.01µF C77 0.01µF C80 0.01µF C81 AGND 0.01µF 3 X 1000pF CAPS BETWEEN DVCC AND AVEE DVCC 1000pF C82 0.01µF C84 DVCC 3 X 00.01µF CAPS BETWEEN DVCC AND AVEE C83 1000pF C85 1000pF C87 AVEE 0.01µF C86 AVEE 0.01µF 12707-007 UG-766 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide 12707-008 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide 12707-009 Figure 8. Evaluation Board Top View Figure 9. Evaluation Board Bottom View Rev. 0 | Page 9 of 11 UG-766 UG-766 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide ORDERING INFORMATION BILL OF MATERIALS Table 1. Qty 21 1 2 Location A0 to A3, D0 to D4, CEB, CLK, DIN, AGND, AVCC, AVEE, DOUT, DVCC, SERB, AGND1, RESETB, UPDATB AGND_B, AVCC_B, AVEE_B, DVCC_B C1, C3, C5, C12, C15, C18, C21, C24, C27, C30, C33, C36, C39, C42, C45, C48, C51, C54, C57, C60, C63, C66, C69 C10 C2, C11, C13, C16, C19, C22, C25, C28, C31, C34, C37, C40, C43, C46, C49, C52, C55, C58, C61, C64, C67, C70, C72, C74, C75, C77, C78, C80 to C82, C84, C86 C4, C6, C14, C17, C20, C23, C26, C29, C32, C35, C38, C41, C44, C47, C50, C53, C56, C59, C62, C65, C68, C71, C73, C76, C79, C83, C85, C87 C7 C8, C9 3 CR1 to CR3 Diode, SMD, LED 26 1 J1 to J26 P1 3 1 1 4 1 1 16 6 1 2 P2, P5, P6 P3 P4 R1, R8, R9, R11 R10 R12 R13 to R28 R2 to R7 RESET RN2, RN3 1 U1 1 U2 1 VUSB Connector, PCB, coaxial, BNC, ST Connector, PCB, header, shrouded, ST, 14P, male Connector, PCB, Berg, jumper, ST, male, 2P Connector, PCB, Berg, header, ST, male, 6P Connector, PCB, USB Type B, R/A, thru hole Resistor, precision, thick film chip, R0402 Resistor, precision, thick film chip, R0402 Resistor, precision, thick film chip, R0402 Resistor, precision, thick film chip, R0402 Resistor, film, SMD, 0402 Switch, SPST, ST, push button Resistor, network, 8-pin, 4 resistors, surface mount IC, other, high performance USB microcontrollers Generic QFN72_10X10_PAD7_7X7_7 footprint chip Connector, PCB, test point, red 1 Y1 IC, crystal oscillator 4 23 1 32 28 Description Connector, PCB, pin, Vector Value K24A W. EYELET T15.23 Manufacturer Vector Part Number K24A W. EYELET T15.23 Connector, PCB, banana jack, uninsulated, STD (version 2 footprint) Capacitor, ceramic, X7R, 0402 108-0740-001 Johnson 108-0740-001 0.1 µF Murata GRM155R71C104KA88D Capacitor, tantalum, chip Capacitor, ceramic, X7R, 0402 10 µF 0.01 µF AVX Panasonic TPSD106K035R0125 ECU-E1C103KBQ Capacitor, ceramic, SMD, 0402 1000 pF Panasonic ECU-E1E102KBQ Capacitor, ceramic, X5R, 0402 Capacitor, ceramic 0.47 µF 22 pF LMK105BJ474KV-F 0402CG220J9B200 CMD67-21VGC/TR8 (green) STETCOJ01001A1944 3M3314-2002 Taiyo Phycomp (Yageo) Chicago Miniature Lamp STETCO 3M J01001A1944 3314-2002 BERG69157-102 SAMTECTSW10608GS6PIN 4-1734376-8 2 kΩ 1 MΩ 10 kΩ 75 Ω 0Ω TP11SH9CBE 22 Ω Berg Samtec AMP Panasonic Panasonic Panasonic Panasonic Panasonic C&K CTS 69157-102 TSW-106-08-G-S 4-1734376-8 ERJ-2RKF2001X ERJ-2RKF1004X ERJ-2RKF1002X ERJ-2RKF75R0X ERJ-2GE0R00X TP11SH9CBE 742C083220JCT PIC18F4550-I/PT Microchip Technology Not applicable PIC18F4550-I/PT GEN_QFN72_10X10_ PAD7_7X7_7 Red 20.000 MHz Rev. 0 | Page 10 of 11 Components Corp ECS CMD67-21VGC/TR8 GEN_QFN72_10X10_ PAD7_7X7_7 TP-104-01-02 ECS-200-20-18 ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide UG-766 NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG12707-0-11/14(0) Rev. 0 | Page 11 of 11