Student Name: ___________________________
CHABOT COLLEGE
CISCO NETWORKING ACADEMY II
e-Labs Checklist
Directions:
 Complete all of the listed e-Labs in each module.
 As you complete each one, mark the checkbox next to it.
 At the close of each chapter, your instructor may hold an e-Lab quiz. During the quiz, you will
be required to demonstrate successful completion of any e-Lab in the current chapter. These
quizzes will count toward your course grade.
Module 1: WANs and Routers Labs:
 1.2.5 Connecting Console Interfaces
 1.2.6 Connecting Router LAN Interfaces
Module 2: Introduction to Routers e-Labs:
 2.1.3a Logging into the Router
 2.1.3b Router User Interface Modes
 2.1.5 Operation of the Cisco IOS
 2.2.6a Keyboard help in the CLI
 2.2.6b IOS Auto-Completion
Module 3: Configuring a Router e-Labs:
 3.1.3a Configuring Router Passwords
 3.1.3b Command-line Interface Command Modes
 3.1.4 On by Default
 3.1.5 Configuring a Serial Interface
 3.1.7 Configuring an Ethernet Interface
 3.2.5 Housekeeping
 3.2.7 Configuring Host Tables
Module 4: Learning about Other Devices e-Labs:
 4.1.3 Implementation, Monitoring and Maintenance of CDP
 4.1.6a Address Resolution Protocol
 4.1.6b CDP Neighbors
 4.2.5 Alternate connectivity Tests – Ping
Module 5: Managing Cisco IOS Software e-Labs:
 5.1.3 Preparing for Boot System Commands
 5.1.4 Configuration Register
 5.1.5 Troubleshooting IOS Boot Failure
Module 6: Routing and Routing Protocols e-Labs:
 6.1.2a Static Route Operation
 6.1.2b Static Routes
 6.1.3 Configuring Static Routes
 6.1.4 Configuring Default Route Forwarding
 6.1.5 Verifying Static Route configuration
 6.1.6 Static Routes
 6.3.2 Routing Configuration
1
Student Name: ___________________________
Module 7: Distance Vector Routing Protocols e-Labs:
 7.2.2 RIP
 7.2.3 Using Classless IP routing
 7.2.5 Verifying RIP Configuration
 7.2.6a Troubleshooting RIP Update Issues
 7.2.6b Troubleshooting RIP
 7.2.7 Preventing Routing Updates Through an Interface
 7.2.9 Load Balancing Across Multiple Paths
 7.2.10 Integrating Static Routes with RIP
 7.3.5 Configuring IGRP
 7.3.6 Configuring Default Routing with RIP and IGRP
 7.3.7a Verifying IGRP Configuration
 7.3.7b IGRP
Module 8: TCP/IP Suite Error and Control Messages (no e-Labs)
Module 9: Basic Router Troubleshooting e-Labs:
 9.1.5 Administrative Distance
 9.2.5 Layer 3 Troubleshooting Using ping
 9.3.1 Troubleshooting Layer 1: Using show interface
 9.3.3 Cisco Discovery Protocol
 9.3.6 Troubleshooting Using show controllers serial

Module 10: Intermediate TCP/IP (no e-Labs)
Module 11: Access Control Lists (ACLs) e-Labs:
 11.1.3 Creating ACLs
 11.1.5 Verifying ACLS
 11.2.1a Configuring a Standard Access List
 11.2.1b Standard ACL
 11.2.1c Standard ACL
 11.2.1d Standard ACL
 11.2.1e Standard ACL
 11.2.2a Configuring an Extended Access List
 11.2.2b Extended ACL
 11.2.2c Extended ACLs
 11.2.2d Extended ACL
 11.2.2e Extended ACL
 11.2.3a Named ACL
 11.2.3b Configuring a Named Access List
 11.2.6 Access Control Lists
2