14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS
STYLE 99
Style 99 Roust-A-Bout couplings are designed with heavy housings and grips to provide
a strong component for joining plain and beveled end, including Schedule 80 steel pipe
and Victaulic plain end fittings. Roust-A-Bout couplings are not designed for use on plastic
pipe, pipe with brittle linings, cast or ductile iron pipe nor any pipe with a surface hardness
greater than 150 Brinell.
Pipe is secured together by heavy jaws, which are set into the housing. All sizes are
supplied with painted housings and plated nuts and bolts. Galvanized housings are
available.
1 ½ – 12'' SIZES
14 – 18'' SIZES
WARNING
Style 99 Roust-A-Bout couplings must be assembled with nuts tightened to full torque
specifications.
Lenntech bv Rotterdamseweg 402m
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
2629HH Delft
MATERIAL SPECIFICATIONS
Exaggerated for clarity
Exaggerated for clarity
1 ½ – 18'' SIZES
1''; 76.1 & 139.7 MM SIZES
Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM
A-395, grade 65-45-15, is available upon special request.
Housing Coating: Orange enamel.
• Optional: Hot dipped galvanized and others.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
Jaws: Carbon steel, case hardened, electroplated, except sizes 1''; 76.1 mm and 139.7 mm, which
utilize stainless steel, Type 416, hardened.
Gasket: (specify choice*)
• Grade “E” EPDM
EPDM (Green color code). Temperature range –30°F to +230°F/–34°C to +110°C. Recommended for cold and hot water service within the specified temperature range plus a
variety of dilute acids, oil-free air and many chemical services. UL classified in accordance
with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C potable water service. NOT
RECOMMENDED FOR PETROLEUM SERVICES.
• Grade “T” nitrile
Nitrile (Orange color code). Temperature range –20°F to +180°F/–29°C to +82°C. Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified
temperature range. Not recommended for hot water services over +150°F/+66°C or for hot dry
air over +140°F/+60°C.
* Services listed are General Service Recommendations only. It should be noted that there are
services for which these gaskets are not recommended. Reference should always be made to the
latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a
listing of services which are not recommended.
Bolts/Nuts/Washers: Heat-treated plated carbon steel, trackhead meeting the physical and chemical
requirements of ASTM A-449 and physical requirements of ASTM A-183. The 6"/150 mm and
larger sizes are supplied with hardened steel washers meeting ASTM F-436 Type 3 (weathering
steel).
JOB/OWNER
CONTRACTOR
ENGINEER
System No. __________________________
Submitted By ________________________
Spec Sect ____________ Para __________
Location ____________________________ Date ________________________________
Approved ___________________________
Date ________________________________
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
14.02_1
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
DIMENSIONS
Size
Y
Z
X
1 – 6"/25 – 150 MM SIZES
Y
Z
X
8 – 12"/200 – 300 MM SIZES
Y
X
14 – 18"/350 – 450 MM SIZES
Lenntech bv
Rotterdamseweg 402m
2629HH Delft
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
Z
Max
Work
Press.
Max.
End
Load
Required
Bolt
Torque
‡
Bolt/Nut
No. – Size
Inches
X
Y
Z
Lbs.
kg
Dimensions
Inches/mm
Aprx.
Weight
Nominal
Size
Inches
mm
Actual
Outside
Diameter
Inches
mm
psi
kPa
Lbs. *
N
Lb. Ft. **
N•m
1
25
1.315
33.7
600
4130
800
3560
35
47.5
2 – 3⁄8 x 2
2.56
65
4.25
108
2.25
57
1.7
0.8
1½
40
1.900
48.3
750
5175
2100
9345
60
81.4
2 – ½ x 2½
3.25
83
5.50
140
2.88
73
3.6
1.6
2
50
2.375
60.3
750
5175
3300
14685
150
203.4
2 – 5⁄8 x 3 ¼
3.75
95
6.75
171
3.38
86
5.3
2.4
2½
65
2.875
73.0
600
4130
3890
17310
150
203.4
2 – 5⁄8 x 3 ¼
4.25
108
7.13
181
3.38
86
5.7
2.5
76.1 mm
3.000
76.1
400
2700
2825
12500
95
128.8
2 – ½ x 2¾
4.69
119
6.25
159
2.75
70
4.4
2.0
3
80
3.500
88.9
600
4130
5770
25676
200
271.2
2 – ¾ x 4¼
5.00
127
8.50
216
3.38
86
8.7
3.9
3½
90
4.000
101.6
500
3450
6280
27946
200
271.2
2 – ¾ x 4¼
5.50
140
9.25
235
3.63
92
10.6
4.8
4
100
4.500
114.3
450
3100
7155
31840
200
271.2
2 – ¾ x 4¼
6.13
156
10.00
254
4.00
102
12.8
5.8
139.7 mm
5.500
139.7
250
1700
5940
26440
160
217.0
2–¾x5
7.80
200
10.75
260
3.19
81
9.0
4.1
5
125
5.563
141.3
350
2400
8500
37825
250
339.0
2 – 7⁄8 x 5
7.25
184
11.38
289
4.38
111
17.3
7.8
6
150
6.625
168.3
300
2065
10340
46013
250
339.0
2–1x6#
8.50
216
13.38
340
4.38
111
23.2
10.5
165.1 mm
6.500
165.1
300
2065
9955
44300
250
339.0
2–1x6#
8.38
213
13.25
337
4.38
111
22.2
10.1
8
200
8.625
219.1
250
1700
14600
64970
250
339.0
4 – 7⁄8 x 5 #
10.88
276
14.38
365
5.00
127
37.2
16.9
10
250
10.750
273.0
250
1700
22700
101015
300
406.8
4 – 7⁄8 x 5 #
13.38
340
16.38
416
5.00
127
48.2
21.9
12
300
12.750
323.9
250
1700
31900
141955
350
474.6
4 – 1 x 6½ #
15.50
394
19.63
499
5.13
130
60.0
27.2
14
350
14.000
355.6
200
1400
30800
137060
350
474.6
8 – 1 x 6½ #
16.75
425
20.75
527
5.38
137
89.0
40.4
16
400
16.000
406.4
150
1000
30200
134390
350
474.6
8 – 1 x 6½ #
19.00
483
22.63
575
5.38
137
105.0
47.6
18
450
18.000
457.0
150
1000
38200
169990
350
474.6
8 – 1 x 6½ #
21.00
533
23.50
597
5.38
137
125.0
56.7
* Working Pressure and End Load are total, from all internal and external loads, based on coupling properly
assembled, with bolts fully torqued to listed specifications, on plain end or beveled end standard weight
(ANSI) steel pipe and Victaulic plain end fittings. Couplings are designed to be used with plain end pipe
and Victaulic plain end fittings only.
** Bolt torque ratings shown must be applied at installation.
‡ Metric thread size bolts (plated) are available (color coded) for all coupling sizes upon request. Contact
Victaulic for details.
WARNING: Depressurize and drain the piping system before attempting to install, remove, or adjust any
Victaulic piping products.
# Supplied with flat washers.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
14.02_2
REV_H
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Carbon Steel Pipe
2
Size
Nominal
Outside Size
Inches
mm
Pipe
Actual
Outside
Diameter
Inches
mm
Wall
Thickness
Inches
mm
0.179
4.55
1
25
1½
40
2
50
2½
65
3
80
3
1.315
33.7
1.900
48.3
2.375
60.3
2.875
73.0
3.500
88.9
Sched.
4
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Lb.Ft.
N•m
psi
kPa
Lbs.
N
80
—
—
0.133
3.38
40
600
4130
800
3560
0.109
2.77
10
600
4130
800
3560
0.065
1.65
5
400
2750
550
2450
0.200
5.08
80
750
5175
2100
9345
0.145
3.68
40
750
5175
2100
9345
0.109
2.77
10
600
4130
1700
7565
0.065
1.65
5
400
2750
1100
4895
0.218
5.54
80
750
5175
3300
14685
0.154
3.91
40
750
5175
3300
14685
0.109
2.77
10
400
2750
1800
8010
0.065
1.65
5
200
1375
900
4005
0.276
7.01
80
600
4130
3890
17310
0.203
5.16
40
600
4130
3890
17310
0.120
3.05
10
300
2065
1900
8455
0.083
2.11
5
150
1035
1000
4450
0.300
7.62
80
600
4130
5770
25675
0.216
5.49
40
600
4130
5770
25675
0.120
3.05
10
225
1550
2160
9610
0.083
2.11
5
125
860
1200
5340
35
47.5
60
81.4
150
203.4
150
203.4
200
271.2
Table continued on page 4.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
14.02_3
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Carbon Steel Pipe
2
Size
Nominal
Outside Size
Inches
mm
3½
90
4
100
5
125
6
150
165.1 mm
8
200
3
Pipe
Actual
Outside
Diameter
Inches
mm
4.000
101.6
4.500
114.3
5.563
141.3
6.625
168.3
6.500
165.1
8.625
219.1
Wall
Thickness
Inches
mm
Sched.
4
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Lb.Ft.
N•m
psi
kPa
Lbs.
N
500
3450
6280
27945
500
3450
6280
27945
200
1375
2500
11125
0.318
8.08
80
0.226
5.74
40
0.120
3.05
10
0.083
2.11
5
100
690
1250
5565
0.337
8.56
80
450
3100
7155
31840
0.237
6.02
40
450
3100
7155
31840
0.120
3.05
10
175
1200
2800
12460
0.083
2.11
5
60
415
950
4230
0.375
9.53
80
350
2410
8500
37825
0.258
6.55
40
350
2410
8500
37825
0.134
3.40
10
150
1035
3600
16020
0.109
2.77
5
75
515
1800
8010
0.432
10.97
80
300
2065
10340
46015
0.280
7.11
40
300
2065
10340
46015
0.134
3.40
10
100
690
3500
15575
0.109
2.77
5
75
515
2600
11570
0.250
6.35
—
300
2065
9955
44300
0.200
5.08
—
175
1200
6000
26700
0.150
3.81
—
100
690
3500
15575
0.322
8.18
40
250
1725
14600
64970
0.277
7.04
30
200
1375
11700
52065
0.148
3.76
10
100
690
6000
26700
0.109
2.77
5
50
345
3000
13350
200
271.2
200
271.2
250
339.0
250
339.0
250
339.0
250
339.0
Table continued on page 5.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
14.02_4
REV_H
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Carbon Steel Pipe
2
Size
Nominal
Outside Size
Inches
mm
10
250
12
300
3
Pipe
Actual
Outside
Diameter
Inches
mm
10.750
273.0
12.750
323.9
Wall
Thickness
Inches
mm
Sched.
4
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Lb.Ft.
N•m
psi
kPa
Lbs.
N
250
1725
22700
101015
175
1200
15900
70755
75
515
6800
30260
0.365
9.27
40
0.307
7.80
30
0.165
4.19
10
0.134
3.40
5
50
345
4500
20025
0.375
9.53
STD
250
1725
31900
141955
0.330
8.38
30
150
1035
19100
84995
0.180
4.57
10
100
690
12700
56515
0.165
4.19
5
75
515
9500
42275
300
406.8
350
474.6
14
350
14.000
355.6
0.375
9.53
STD
350
474.6
200
1375
30800
137060
16
400
16.000
406.4
0.375
9.53
STD
350
474.6
150
1035
30200
134390
COLUMN 1: Victaulic couplings are identified by nominal pipe size.
COLUMN 2: Nominal pipe wall thickness.
COLUMN 3: Pipe wall thickness schedule as established in ANSI Standard B36, 10-70.
COLUMN 4: Bolt torque required for installing Victaulic plain end couplings to achieve pressure ratings
listed in Column 5 and Permissible Maximum End Loads listed in Column 6.
TORQUE RATINGS MUST BE APPLIED AT INSTALLATION.
COLUMN 5: Maximum line pressure, including surge, to which a joint should be subjected, based on
couplings assembled to full torque specifications on plain end or beveled end standard weight
steel pipe and/or Victaulic plain end fittings. Working pressure ratings are based on pipe prepared in
accordance with Victaulic specifications.
COLUMN 6: Maximum end load from all internal and/or external forces to which the joint should be
subjected based on couplings assembled to full torque specifications.
NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips
set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼''/6.4 mm.
This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to
provide linear or angular movement.
ROUST-A-BOUT STYLE 99 COUPLINGS ARE DESIGNED FOR USE WITH PLAIN END OR BEVELED END PIPE
AND VICTAULIC PLAIN END FITTINGS ONLY.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
14.02_5
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Stainless Steel Pipe
2
Size
Nominal
Size
Inches
mm
1
33.4
1½
48.3
2
60.3
2½
73.0
Pipe
Actual
Outside
Diameter
Inches
mm
1.315
33.7
1.900
48.3
2.375
60.3
2.875
73.0
Wall
Thickness
Inches
mm
3½
101.6
4
114.3
5
141.3
4.000
101.6
4.500
114.3
5.563
141.3
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Lb.Ft.
N•m
psi
kPa
Lbs.
N
40
35
47.5
600
4130
800
3560
0.109
2.77
10
35
47.5
400
2750
550
2450
0.065
1.65
5
35
47.5
250
1725
350
1555
0.145
3.56
40
60
81.4
500
3450
1.400
6230
0.109
2.77
10
60
81.4
400
2750
1.100
4895
0.065
1.65
5
N/R
N/R
N/R
0.154
3.91
40
150
203.4
500
3450
2.200
9790
0.109
2.77
10
150
203.4
400
2750
1.800
8010
0.065
1.65
5
N/R
N/R
N/R
0.203
5.16
40
150
203.4
400
2750
2.500
11125
0.120
5.16
10
150
203.4
250
1725
1.500
6675
5
N/R
N/R
N/R
40
200
271.2
400
2750
3.800
16910
0.120
3.05
10
200
271.2
200
1375
1.900
8455
0.083
2.11
5
N/R
N/R
N/R
0.226
5.74
40
200
271.2
300
2065
3.700
16465
0.120
3.05
10
200
271.2
150
1035
1.900
8455
0.083
2.11
2.11
0.216
5.49
3.500
88.9
Sched.
4
0.133
3.38
0.083
3
88.9
3
5
N/R
N/R
N/R
0.237
6.02
40
200
271.2
250
1725
3.900
17355
0.120
3.05
10
200
271.2
80
550
1.300
5785
0.083
2.11
5
N/R
N/R
N/R
0.258
6.55
40
250
339.0
200
1375
4.800
21360
0.134
3.40
10
250
339.0
75
510
1.800
8010
0.109
2.77
5
N/R
N/R
N/R
Table continued on page 7.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
14.02_6
REV_H
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Stainless Steel Pipe
2
Size
Nominal
Size
Inches
mm
6
168.3
165.1 mm
8
219.1
10
273.0
12
323.9
3
Pipe
Actual
Outside
Diameter
Inches
mm
6.625
168.3
6.500
165.1
8.625
219.1
10.750
273.0
12.750
323.9
Wall
Thickness
Inches
mm
Sched.
4
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Lb.Ft.
N•m
psi
kPa
Lbs.
N
0.280
7.11
40
250
339.0
200
1375
6.800
30260
0.134
3.40
10
250
339.0
75
515
2.600
11570
0.109
2.77
5
N/R
N/R
N/R
0.280
7.11
40
250
339.0
200
1375
6.800
30260
0.134
3.40
10
250
339.0
75
515
2.600
11570
0.109
2.77
5
N/R
N/R
N/R
0.322
8.18
40
250
339.0
200
1375
11.000
48950
0.148
3.76
10
250
339.0
75
515
4.400
19580
0.109
2.77
5
250
339.0
25
170
1.460
6495
0.365
9.27
40
300
406.8
100
690
9.000
40050
0.165
4.19
10
300
406.8
50
345
4.500
20025
0.134
3.40
5
300
406.8
25
170
2.250
10010
0.406
10.31
40
350
474.6
100
690
12.750
56735
0.180
4.67
10
350
474.6
50
345
6.400
28480
0.156
3.96
5
350
474.6
25
170
3.200
14240
NR = Not recommended
+ Contact Victaulic for details.
COLUMN 1: Victaulic couplings are identified by nominal pipe size.
COLUMN 2: Nominal pipe wall thickness.
COLUMN 3: Pipe wall thickness schedule as established in ANSI Standard B36, 10-70.
COLUMN 4: Bolt torque required for installing Victaulic plain end couplings to achieve pressure ratings
listed in Column 5 and Permissible Maximum End Loads listed in Column 6.
TORQUE RATINGS MUST BE APPLIED AT INSTALLATION.
COLUMN 5: Maximum line pressure, including surge, to which a joint should be subjected, based on
couplings assembled to full torque specifications on plain end or beveled end standard weight
steel pipe and/or Victaulic plain end fittings. Working pressure ratings are based on pipe prepared in
accordance with Victaulic specifications.
COLUMN 6: Maximum end load from all internal and/or external forces to which the joint should be
subjected based on couplings assembled to full torque specifications.
NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as
grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed
¼''/6.4 mm). This should be considered for installations in tightly confined areas. Style 99 couplings are not
designed to provide linear or angular movement.
ROUST-A-BOUT STYLE 99 COUPLINGS ARE DESIGNED FOR USE WITH PLAIN END OR BEVELED END PIPE
AND VICTAULIC PLAIN END FITTINGS ONLY.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
14.02_7
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Aluminum Pipe*
2
4
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Sched.
Lb.Ft.
N•m
psi
kPa
Lbs.
N
0.179
4.55
80
N/R
N/R
N/R
0.133
3.38
40
35
47.5
600
4130
800
3560
0.109
2.77
10
35
47.5
300
2065
400
1780
0.065
1.65
5
35
47.5
100
690
135
601
0.200
5.08
80
60
81.4
500
3450
1400
6230
0.145
3.56
40
60
81.4
400
2760
1100
4895
0.109
2.77
10
60
81.4
300
2065
825
3671
0.065
1.65
Size
Nominal
Size
Inches
mm
1
25
1½
40
2
50
2½
65
3
80
3
Pipe
Actual
Outside
Diameter
Inches
mm
1.315
33.7
1.900
48.3
2.375
60.3
2.875
73.0
3.500
88.9
Wall
Thickness
Inches
mm
5
N/R
N/R
N/R
0.218
5.54
80
150
203.4
400
2760
1800
8010
0.154
3.91
40
150
203.4
300
2065
1300
5785
0.109
2.77
10
150
203.4
200
1380
900
4005
0.065
1.65
5
N/R
N/R
N/R
0.276
7.01
80
150
203.4
350
2415
2200
9790
0.203
5.16
40
150
203.4
275
1895
1725
7676
0.120
5.16
10
150
203.4
150
1035
1000
4450
0.083
2.11
5
N/R
N/R
N/R
0.300
7.62
80
200
271.2
300
2065
2880
12816
0.216
5.49
40
200
271.2
200
1380
1920
8544
0.120
3.05
10
200
271.2
100
690
960
4272
0.083
2.11
5
N/R
N/R
N/R
Table continued on page 9.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
14.02_8
REV_H
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Aluminum Pipe*
2
Size
Nominal
Size
Inches
mm
3½
90
4
100
5
125
6
150
8
200
3
Pipe
Actual
Outside
Diameter
Inches
mm
4.000
101.6
4.500
114.3
5.563
141.3
6.625
168.3
8.625
219.1
Wall
Thickness
Inches
mm
Sched.
4
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Lb.Ft.
N•m
psi
kPa
Lbs.
N
0.318
8.08
80
200
271.2
250
1725
3100
13795
0.226
5.74
40
200
271.2
200
1380
2500
11125
0.120
3.05
10
200
271.2
100
690
1250
5563
0.083
2.11
5
N/R
N/R
N/R
0.337
8.56
80
200
271.2
200
1380
3200
14240
0.237
6.02
40
200
271.2
150
1035
2400
10680
0.120
3.05
10
200
271.2
50
345
800
3560
0.083
2.11
5
N/R
N/R
N/R
0.375
9.53
80
250
339.0
150
1035
3600
16020
0.258
6.55
40
250
339.0
100
690
2400
10680
0.134
3.40
10
250
339.0
50
345
1200
5340
0.109
2.77
5
N/R
N/R
N/R
0.432
10.97
80
250
339.0
150
1035
5200
23140
0.280
7.11
40
250
339.0
100
690
3500
15575
0.134
3.40
10
250
339.0
50
345
1750
7788
0.109
2.77
5
250
339.0
35
240
1225
5451
0.322
8.18
40
250
339.0
150
1035
9000
40050
0.277
7.04
30
250
339.0
100
690
6000
26700
0.250
6.35
20
250
339.0
75
515
4500
20025
0.148
3.76
10
250
339.0
50
345
3000
13350
Table continued on page 10.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
14.02_9
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
PRESSURE RATINGS AND END LOADS
1
Aluminum Pipe*
2
Size
Nominal
Size
Inches
mm
10
250
12
300
3
Pipe
Actual
Outside
Diameter
Inches
mm
10.750
273.0
12.750
323.9
Wall
Thickness
Inches
mm
Sched.
4
5
6
Req’d
Bolt
Torque
Max.
Joint
Working
Pressure
Max.
Permiss.
End Load
Lb.Ft.
N•m
psi
kPa
Lbs.
N
0.356
9.27
40
300
406.8
100
690
9000
40050
0.307
7.80
30
300
406.8
75
515
6300
28035
0.250
6.35
20
300
406.8
50
345
4500
20025
0.165
4.19
10
300
406.8
25
172
2250
10013
0.406
10.31
40
300
406.8
100
690
12800
56960
0.330
8.38
30
300
406.8
75
515
9500
42275
0.250
6.35
20
300
406.8
50
345
6000
26700
0.180
4.67
10
300
406.8
25
172
3150
14018
* Aluminum Pipe – Alloy 6063-T6 or 6061-T6 in Schedule 80 and 40; Alloy 6063-T6 in Schedule 30, 20, 10
and 5.
NR = Not recommended
COLUMN 1: Victaulic couplings are identified by nominal pipe size.
COLUMN 2: Nominal pipe wall thickness.
COLUMN 3: Pipe wall thickness schedule as established in ANSI Standard B36, 10-70.
COLUMN 4: Bolt torque required for installing Victaulic plain end couplings to achieve pressure ratings
listed in Column 5 and Permissible Maximum End Loads listed in Column 6.
TORQUE RATINGS MUST BE APPLIED AT INSTALLATION.
COLUMN 5: Maximum line pressure, including surge, to which a joint should be subjected, based on
couplings assembled to full torque specifications on plain end or beveled end standard weight
steel pipe and/or Victaulic plain end fittings. Working pressure ratings are based on pipe prepared in
accordance with Victaulic specifications.
COLUMN 6: Maximum end load from all internal and/or external forces to which the joint should be
subjected based on couplings assembled to full torque specifications.
NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips
set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼''/6.4 mm.
This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to
provide linear or angular movement.
ROUST-A-BOUT STYLE 99 COUPLINGS ARE DESIGNED FOR USE WITH PLAIN END OR BEVELED END PIPE
AND VICTAULIC PLAIN END FITTINGS ONLY.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
14.02_10
REV_H
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
INSTALLATION
Reference should always be made to the I-100 Victaulic Field Installation Handbook for the product
you are installing. Handbooks are included with each shipment of Victaulic products for complete
installation and assembly data, and are available in PDF format on our website at www.victaulic.com.
WARRANTY
Refer to the Warranty section of the current Price List or contact Victaulic for details.
NOTE
This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be
installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the
right to change product specifications, designs and standard equipment without notice and without
incurring obligations.
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
14.02_11
14.02
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
Roust-A-Bout® Couplings
STYLE 99
Lenntech
info@lenntech.com
www.lenntech.com
Tel. +31-15-261.09.00
Fax. +31-15-261.62.89
WCAS-6UPKCK
For complete contact information, visit www.victaulic.com
14.02
1671 REV H
UPDATED 3/2007
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
14.02