GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
PART 1 GENERAL
1.01
SUMMARY
A. Section Includes
1. Asphaltic modified bituminous roofing
2. Insulation
B. Related Sections
1. Section 06100: Rough Carpentry
2. Section 07620: Sheet Metal Flashing and Trim
3. Section 15430: Plumbing Specialties
C. References
1. Factory Mutual (FM Global) - Approval Guide
2. Underwriters Laboratories (UL) - Roofing Systems and Materials Guide (TGFU R1306
3. American Society for Testing and Materials (ASTM) - Annual Book of ASTM Standards
4. Sheet Metal and Air Conditioning Contractors National Association, Inc. (SMACNA) Architectural Sheet Metal Manual
5. Asphalt Roofing Manufacturers Association (ARMA)
6. National Roofing Contractors Association (NRCA)
7. American Society of Civil Engineers (ASCE)
1.02
PERFORMANCE REQUIREMENTS
A. Provide an installed roofing membrane and base flashing system that does not permit the
passage of water, and will withstand the design pressures calculated in accordance with the
most current revision of ASCE 7.
B. GAF® shall provide all primary roofing materials that are physically and chemically
compatible when installed in accordance with manufacturers current application
requirements.
1.03
SUBMITTALS
A. Product Data: Provide product data sheets for each type of product indicated in this section.
B. Shop Drawings: Provide manufacturers standard details and approved shop drawings for
the roof system specified.
C. Samples: Provide samples of insulation(s), fasteners and roll goods for verification of
quality.
D. Certificates: Installer shall provide written documentation from the manufacturer of their
authorization to install the roof system, and eligibility to obtain the warranty specified in this
section.
1.04
QUALITY ASSURANCE
07550-0
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
A. Manufacturer’s Qualifications: GAF® shall provide a roofing system that meets or exceeds
all criteria listed in this section.
B. Installer’s Qualifications:
1. Installer shall be classified as a Master Select contractor as defined and certified by
GAF®.
2. Installer shall be classified as a Master contractor as defined and certified by GAF®.
3. Installer shall be classified as an Authorized contractor as defined and certified by
GAF®.
C. Source Limitations: All components listed in this section shall be provided by a single
manufacturer or approved by the primary roofing manufacturer.
D. Final Inspection
1. Manufacturers representative shall provide a comprehensive final inspection after
completion of the roof system. All application errors must be addressed and final punch
list completed.
1.05
PRE-INSTALLATION CONFERENCE
A. Prior to scheduled commencement of the roofing installation and associated work, conduct a
meeting at the project site with the installer, architect, owner, GAF® representative and any
other persons directly involved with the performance of the work. The installer shall record
conference discussions to include decisions and agreements reached (or disagreements),
and furnish copies of recorded discussions to each attending party. The main purpose of
this meeting is to review foreseeable methods and procedures related to roofing work.
1.06
REGULATORY REQUIREMENTS
A. All work shall be performed in a safe, professional manner, conforming to all federal, state
and local codes.Exterior Fire Test Exposure: Provide a roofing system that will achieve an
Underwriters Laboratories rating for roof slopes indicated.UL Class A
2. UL Class B
3. UL Class C
4. Roof Slope:_______________
C. Windstorm Classification: Provide a roofing system which will achieve a Factory Mutual
wind uplift rating, as listed in the current FM Approval Guide.
1. FM 1-60
2. FM 1-75
3. FM 1-90
1.07
DELIVERY, STORAGE AND HANDLING
A. Deliver all roofing materials to the site in original containers, with factory seals intact. All
products are to carry either a GAF® or BMCA® label.
B. Store all pail goods in their original undamaged containers in a clean, dry location within
their specified temperature range.
07550-1
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
C. Store roll goods on end on pallets in a clean, dry, protected area. Take care to prevent
damage to roll ends or edges. Do not double stack modified bitumen products.
D. Do not expose materials to moisture in any form before, during, or after delivery to the site.
Reject delivery of materials that show evidence of contact with moisture.
E. Remove manufacturer supplied plastic covers from materials provided with such. Use
“breathable” type covers such as canvas tarpaulins to allow venting and protection from
weather and moisture. Cover and protect materials at the end of each work day. Do not
remove any protective tarpaulins until immediately before the material is to be installed.
F. Materials shall be stored above 55°F (12.6°C) a minimum of 24 hours prior to application.
1.08
PROJECT CONDITIONS
A. Weather
1. Proceed with roofing only when existing and forecasted weather conditions permit.
2. Ambient temperatures must be above 45°F (7.2°C) when applying hot asphalt or water
based adhesives.
1.09
WARRANTY
A. Provide Manufacturers standard Diamond Pledge Guarantee with single source
coverage* and no monetary limitation, where the manufacturer agrees to repair or replace
components in the roofing system, which cause a leak due to a failure in materials or
workmanship.
1. Duration: Five (5), Ten (10) years from the date of completion.
B. Provide Manufacturers standard System Pledge Guarantee with single source coverage*
and a monetary limitation of one (1) dollar per square foot, where the manufacturer agrees
to repair or replace components in the roof system, which cause a leak due to failure in
materials or workmanship.
1. Duration: Five (5), Ten (10) years from the date of completion.
C. Provide Manufacturers standard Labor and Material Guarantee where the manufacturer
agrees to repair or replace the portion of the roofing materials, which have resulted in a leak
due to a manufacturing defect or defects caused by ordinary wear and tear.
1. Duration: Five (5), Ten (10) years from the date of completion.
D. Provide Manufacturers standard prorated Limited Material Warranty where the
manufacturer agrees to repair or replace to portion of the roofing materials that have
resulted in a leak due to a manufacturing defect or defects caused by ordinary wear and tear
1. Ply Sheets: Ten (10) years
2. Coated Membranes: Twelve (12) years
*Materials and workmanship of listed products within this section when installed in
accordance with current GAF® application and specification requirements. Contact GAF®
Contractor Services for the full terms and conditions of the guarantee.
07550-2
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
PART 2 PRODUCTS
2.01
ACCEPTABLE MANUFACTURER
A. GAF - 1361 Alps Road, Wayne, NJ 07470 http://www.gaf.com
2.02
INSULATION ACCESSORIES
A. Cant Strip: Factory fabricated rigid perlite strip cut at angles to provide a true 45 Angle
between horizontal and vertical surfaces, EnergyGuard Perlite Cant Strip, by BMCA®
B. Tapered Edge Strip: Factory fabricated rigid perlite strip cut at angles to provide a smooth
transition between differences in elevation. EnergyGuard Tapered Edge Strip, by
BMCA®
2.03
MEMBRANE MATERIALS
A. Asphalt coated glass fiber reinforced base sheet: Conforms to or exceeds requirements of
ASTM D 4601, Type II, UL Type G2 BUR. Each roll contains three (3) squares (320 sf) of
material, approximately 39.4 inches by 97.5 feet (1000 mm by 29700 mm); 75 lb (34.1 kg),
GAFGLAS #75 base sheet.
B. Heavy duty, asphalt coated, glass fiberreinforced base sheet: Conforms to or exceeds
requirements of ASTM D 4601, Type II, UL Type G2 BUR. Each roll contains two (2)
squares (214 sf) of material, approximately 39.4 inches by 65.2 feet (1000 mm by 19900
mm); 75 lbs. (34.1 kg), GAFGLAS #80 ULTIMA base sheet.
C. Asphalt coated, glass fiber reinforced, mechanically fastened venting base sheet: Conforms
to or exceeds requirements of ASTM D 3672 Type II and ASTM D 4897, Type II and UL
Type G2 BUR. Each roll contains one square of material, approximately 39.4 inches by
32.6 feet (1000 mm by 9900 mm); 69 lb (31 kg), GAFGLAS STRATAVENT Eliminator
Nailable base sheet.
D. ENERGY STAR listed, fire retarding, coated extra fine mineral granule surfaced modified
bitumen membrane containing a core of non-woven polyester mat coated with fire retardant
APP polymer modified asphalt designed for heat weld application. Conforms to or exceeds
requirements of ASTM D6222 Type II Grade G. Each roll contains one square of material,
approximately 39.6” x 32.4’ (1 m x 10.3 m), Ruberoid EnergyCap Torch Plus FR
2.04
FLASHING MATERIALS
A. Asphalt coated glass fiber reinforced base sheet: Conforms to or exceeds requirements of
ASTM D 4601, Type II, UL Type G2 BUR. Each roll contains three (3) squares (320 sf) of
material, approximately 39.4 inches by 97.5 feet (1000 mm by 29700 mm); 75 lb (34.1 kg),
GAFGLAS #75 base sheet.
B. Heavy duty, asphalt coated, glass fiberreinforced base sheet: Conforms to or exceeds
requirements of ASTM D 4601, Type II, UL Type G2 BUR. Each roll contains two (2)
squares (214 sf) of material, approximately 39.4 inches by 65.2 feet (1000 mm by 19900
mm); 75 lbs. (34.1 kg), GAFGLAS #80 ULTIMA base sheet.
07550-3
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
C. Asphalt coated glass fiber ply sheet, strong and lightweight. Conforms to or exceeds
requirements of ASTM D 2178 Type IV and UL Type G1 BUR Each roll contains five (5)
squares (530 sf) of material, approximately 39.4 inches by 161.8 feet (1000 mm by 49300
mm), 40 lb (18.2 kg), GAFGLAS Ply 4 ply sheet.
D. Premium asphalt coated glass fiber ply sheet with flexible Design: Conforms to or exceeds
requirements of ASTM D 2178 Type VI and UL Type G1 BUR. Each roll contains five (5)
squares (530 sf) of material, approximately 39.4 inches by 161.8 feet (1m by 49.3 m), 44 lb
(20 kg), GAFGLAS FlexPly 6 ply sheet.
E. Smooth surfaced modified bitumen membrane with a non-woven polyester reinforcing mat
coated with APP polymer-modified asphalt. Conforms to or exceeds requirements of ASTM
D 6222 Type I Grade S. Each roll contains one square of material, approximately 39.4
inches by 32.9 feet (1 m by 10 m), 87 lb (39.5 kg) Ruberoid Torch Smooth flashing
membrane.
F. Granule surfaced modified bitumen membrane with a non-woven polyester reinforcing mat
coated with APP polymer-modified asphalt. Conforms to or exceeds requirements of ASTM
D 6222 Type I Grade G. Each roll contains one square of material, approximately 39.4
inches by 32.9 feet (1 m by 10 m), 102 lb (46.4 kg) Ruberoid Torch Granule flashing
membrane.
G. Fire retardant, granule surfaced modified bitumen membrane with a non-woven polyester
reinforcing mat coated with APP polymer-modified asphalt. Conforms to or exceeds the
requirements of ASTM D 6222 Type II Grade G. Each roll contains 3/4 square of material,
approximately 39.4 inches by 24.6 feet (1 m by 7m), 90 lb (40.9 kg) Ruberoid Torch FR
flashing membrane.
H. ENERGY STAR listed, fire retarding, coated extra fine mineral granule surfaced modified
bitumen membrane containing a core of non-woven polyester mat coated with fire retardant
APP polymer modified asphalt designed for heat weld application. Conforms to or exceeds
requirements of ASTM D6222 Type II Grade G. Each roll contains one square of material,
approximately 39.6” x 32.4’ (1 m x 10.3 m), Ruberoid EnergyCap Torch Plus FR
I.
2.05
ENERGY STAR listed, fire retarding, coated extra fine mineral granule surfaced modified
bitumen membrane containing a core of non-woven polyester mat coated with fire retardant
APP polymer modified asphalt designed for heat weld application. Conforms to or exceeds
requirements of ASTM D6222 Type I Grade G. Each roll contains one square of material,
approximately 39.6” x 32.4’ (1 m x 10.3 m), Ruberoid EnergyCap Torch Granule FR
BITUMEN / ADHESIVES
A. Asphalt Bitumen: ASTM D 312 Type III, IV
B. Asphalt Primer: ASTM D 41, Leak Buster Matrix 307 Premium Asphalt Primer, by BMCA.
C. Insulation Adhesive: Matrix 157 Monster Grip, by BMCA.
D. Insulation Adhesive: Oly-Bond 500 distributed by BMCA.
07550-4
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
E. Insulation Adhesive: Insta-Stik by Dow Chemical.
*It is the responsibility of those involved with the design of the building to attain
indemnification for the attachment and integrity of the Insta-Stik Product. GAF® assumes
no responsibility for the Insta-Stik product or its performance within the system.
2.06
ACCESSORIES
A. FLASHING ACCESSORIES
1. Two piece fascia system with continuous ancor cleat and exterior fascia cover available
in 10 foot lengths, M-Weld Gravel Stop MB Fascia by GAF®
a)
Color:
2. Three piece fascia system with continuous galvanized steel spring clip, exterior fascia
and continuos compression flashing bar available in 10 foot lengths, M-Weld Gravel
Guard MB Fascia by GAF®.
a)
Color:
3. Three piece fasia assembly with rigid extruded termination base plate, galvanized or
aluminum extension cleat and decorative snap-on fascia cover available in ten foot
lengths, M-Weld EZ Fascia EX by GAF®.
a)
Color:
4. Metal coping cap with galvanized steel anchor cleats and gutter support chairs available
in 10 foor lengths, M-Weld Snap-On Coping by GAF®.
a)
Color:
B. PENETRATION ACCESSORIES
1. One part moisture curing polyether sealant liquid flashing paired with TOPCOAT
Flashing Fabric at flashing areas over granule surfaced membrane. Conforming to
ASTM D2369, EPA method 24 and meeting the California VOC requirements,
TOPCOAT® Matrix™ MajorSeal™ Liquid Flashing by GAF®.
2. Non-woven, 100% fully spun-bonded polyester fabric used in conjunction with
TOPCOAT® Flashing Grade, Matrix™ MajorSeal™, SB-900 and FlexSeal at all
penetrations, joints or other high shear or stress areas. TOPCOAT® Flashing Fabric by
GAF®.
07550-5
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
3. A spun aluminum vent, pre-flashed with SBS or APP modified bitumen membrane
designed to waterproof soil pipes and roofing protrusions. The M-Vent Standard, by
GAF®.
NOTE: Not for use over active pipes that emit steam or excessive moisture vapor,
condensation may occur. Not for use over boiler or heater/furnace vent pipes.
4. A two-piece roof-flashing unit consisting of a pre-flashed SBS or APP modified bitumen
membrane spun aluminum base and a flexible upper boot, allowing for waterproofing of
tall or awkward roof protrusions. The M-Vent Adjustable, by GAF®.
5. Pressure relief device consisting of a one-piece spun aluminum vent pre-flashed with
SBS or APP modified bitumen membrane. Internally, the vent contains a neoprene
valve that allows air pressure and moisture vapor to escape out of the system without
allowing additional air and moisture vapor to return. The M-Vent One Way, by GAF®.
6. A spun aluminum (or copper) roof drain with gravel guard, strainer cap, and
waterproofing plumbing seal attached. Pre-flashed with SBS or APP modified bitumen
membrane and available in full and insert sizes to accommodate new construction and
retrofit applications. The M-Drain, by GAF®.
7. A Pre-flashed metal through-wall roof drain designed for easy installation to aid in quick
lateral removal of water. The M-Scupper, by GAF®.
8. A structural urethane outer shell, bonded to the roof surface, filled with a urethane
rubber sealant. The urethane sealant conforms to the shape of any roof penetration
through a roof surface to protect the roof system from moisture. The M-Curb and MThane, by GAF®.
C. FIELD OF ROOF ACCESSORIES
1. Low VOC, water based coating system that provides outstanding flame spread and
penetration protection to combustible roof decks in the event of fire. Using patent
pending FireShield® technology, provides UL Class A performance with torch applied or
self adhering modified bitumen roof systems. FireOut™ Fire Barrier Coating, by
GAF®.
2. Elastic non-solvent mastic that cures to a durable rubber bond with exposure to
atmosphere moisture. Meets Federal Specification TT-S 00230-C type II, M-Bond
Adhesive/Sealant, by GAF®.
3. Commercial grade roofing sealant that provides a 100% watertight seal that keeps water
out at the most vulnerable areas of your roof (roof protrusions, step flashings, skylights,
chimneys, vents, gutters, etc) and comes with a 20 yr ltd warranty against leaks caused
07550-6
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
by manufacturing defects. Meets the performance criteria of ASTM D412, ASTM D2196,
ASTM D1475 and ASTM D1644, TOPCOAT® FlexSeal™ Roofing Sealant by GAF®.
4. Factory fabricated assemblies used to accommodate three-dimensional joints in a roof
structure. Heavy reinforced flexible cover with a flexible flame retardant foam bellows for
support. Nailing flanges conform to curb irregularities. Metalastic Expansion Joint
Cover, by GAF®.
5. Coats the exposed asphalt bleed-out at the seams of BUR and Modified Bitumen roofs.
Color matched to help the seams blend in over time with the color of white cap sheets
and special order colors. SeamCote™ Elastomeric Protective Coating, by GAF®.
*****FOR ENERGYCAP SPECS ONLY*****
6. Brilliant white, water based, low VOC, highly reflective elastomeric coating which cures
to form a seamless rubber membrane. Designed to treat seams, laps, flashings and
other edges and details in reflective cap sheet products such as EnergyCap™.
Designed to add reflectivity and protect areas of asphalt bleed-out on white reflective
asphalt roll roofing to give a uniform, brilliant white finish across the whole roof area,
EnergyCote™ Coating by GAF®.
PART 3 EXECUTION
3.01
EXAMINATION
A. Verify that the surfaces and site conditions are ready to receive work.
B. Verify that the deck is supported and secured.
C. Verify that the deck is cleaned and smooth, free of depressions, waves, or projections, and
properly sloped to drains, valleys, eaves, scuppers or gutters.
D. Verify that the deck surfaces are dry and free of ice or snow.
E. Verify that all roof openings, curbs, pipes, sleeves, ducts, vents or other penetrations
through the roof are solidly set, and that all flashings are tapered.
3.02
SUBSTRATE PREPARATION
A. Structural Concrete Deck
1. Minimum deck thickness for structural concrete is 4” (10.2 cm).
2. Only poured in place concrete decks that provide bottom side drying are acceptable.
Decks that are installed over non-vented metal decks or pans that remain in place may
trap moisture in the deck beneath the roof system and are not acceptable.
3. The roof deck shall be properly cured prior to application of the roofing system; twentyeight (28) days is normally required for proper curing. Curing agents must be checked
for compatibility with roofing materials. Prior to the installation of the roof assemblies,
07550-7
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
4.
5.
6.
7.
8.
3.03
GAF® recommends the evaluation of the surface moisture and deck’s dryness through
the use of ASTM D-4263 or hot bitumen test.
The deck must be smooth, level and cannot be wet or frozen. If deck is determined to be
wet, it must be allowed to dry.
Treat cracks greater than 1/8” (3 mm) in width in accordance with the deck
manufacturer’s recommendations.
Sumps for the roof drains shall be provided in the casting of the deck.
When insulation or roofing is to be adhered with hot asphalt, prime the deck with
asphalt/concrete primer, ASTM D 41 at the rate of one gallon per 100 square feet (0.4
L/m2). Allow the primer to dry prior to the application of the roofing system.
In all retrofit roof applications, it is required that deck be inspected for defects. Any
defects are to be corrected per the deck manufacturer’s recommendations prior to the
new roof application.
INSTALLATION - GENERAL
A. Install GAF®’s Ruberoid® roofing system according to all current application requirements in
addition to those listed in this section.
B. GAF® Ruberoid Specification #: NN-1-1-TGPFREC
C. When the slope of the roof is ¾” per foot or greater, install all plies parallel with the slope of
the roof, and install intermediate wood nailers as required for the specific roof slope. Plies
must extend over ridges and nailed on 6” centers.
D. Start the application of membrane plies at the low point of the roof or at the drains, so that
the flow of water is over or parallel to, but never against the laps.
3.04
VAPOR RETARDER
1. Install in accordance with provisions of section 07260
3.05
BASE SHEET
A. Roll the base sheet out over the prepared substrate and allow it to relax. Lap the base
sheet so the flow of water is over or parallel to, but never against the laps.
B. Lap the base sheet 2” (5.1 cm), and 4” (10.2 cm) on the ends, with adjacent laps a minimum
of 18” (45.7 cm) apart.
C. Turn base sheet up and past the top of the cant. Install over
D. At edge terminations, turn the membrane down the face of the wall 2” and fasten every 6”
o.c. with appropriate fasteners.
E. A minimum FMRC 1-60 attachment is recommended. Refer to FMRC Approval Guide for
FM Fastening patterns. Factory Mutual requires fastener density increases in perimeter and
corner zones for FM 1-60 and FM 1-90 or greater. Refer to FM Loss Prevention Data Sheets
1-7, 1-28, 1-29 and 1-49.
07550-8
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
Note: When fastening base sheets using screws and plates without insulation, the plate
must be of a design that allows it to lie flat on the deck.
3.06
BASE SHEET
A. Roll the base sheet out dry, granule surface down, over the prepared substrate and allow it
to relax. Lap the base sheet so the flow of water is over or parallel to, but never against the
laps.
B. Lap the base sheet 2” (5.1 cm), and 4” (10.2 cm) on the ends, with adjacent laps a minimum
of 18” (45.7 cm) apart.
C. Turn base sheet past the top of the cant and continue up the vertical wall terminating at final
base flashing height.
D. At edge terminations, turn the membrane down the face of the wall 2” and fasten every 6”
o.c. with appropriate fasteners.
3.07
CAP SHEET
A. The surface over which the membrane is to be installed must be clean, smooth, dry and
prepared in accordance with article 3.02 “Substrate Preparation”. Do not apply membrane
directly to a fresh asphalt glaze or flood coat, or over base plies with excessive asphalt
mopping bleed out at laps.
B. For slopes 3/4 “ per foot (6.2 cm per meter) and over, membrane must be run parallel to the
roof slope and back nailed in accordance with GAF® steep slope application requirements.
On slopes less than 3/4” per foot (6.2 cm per meter), install cap sheet perpendicular to the
slope.
C. Never apply membrane by any method except welding with a propane torch or other
equipment specifically designed for application of torchable modified bitumen.
D. The coiled membrane must be unrolled approximately 10 ft. (3 meters), and aligned. The
propane torch flame is then applied uniformly across the exposed back surface of the
membrane and lap areas until the compound reaches the proper application temperature
and exhibits a slight sheen. A complete burn-off of release films where present on the
underside of the rolls, membrane selvage edges or both surfaces is necessary. Avoid
overheating which may result in damage to or improper adhesion of the membrane. (The
flame should be moved from side to side in the shape of an “L”, applying about 75% of the
heat to the membrane and 25% to the substrate or underlying plies including the lap area of
the previously installed courses.) The membrane is slowly unrolled as heat is applied to
ensure proper adhesion. When complete, re-roll the opposite end of the membrane and
install in the same manner.
E. A minimum 3/8” (10 mm) bitumen flow-out must be obtained at all seam areas. Dry laps are
not acceptable. To ensure the proper 3/8” (10mm) flow of bitumen at the seam areas, a
roller may be used. Roller application should follow behind the torch no more than 4 ft. (1.2
m) nor less than 3 ft. (0.91 m) to be sure that the membrane will be at the proper
07550-9
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
temperature to produce proper flow. Hand rollers or “walking-in the seam” methods are also
acceptable. Check all seams for full and uniform adhesion. Un-adhered seams must be
lifted with a heated trowel and resealed by lightly torching the seam area.
F. (Optional) Matching granules may be broadcast into the modified bitumen bleed out at
seams while hot to enhance the finished appearance of the membrane.
G. All end laps must be staggered a minimum of 18” (45.7 cm) so that no adjacent end laps
coincide. If end laps fall in line or are not staggered the proper distance, a full width of
membrane must be installed over the end laps. End laps, flashing sheets and other seams
formed over granule surfaces require pre-heating of the top surface of the underlying
granule surface membrane to a point where the granules just begin to sink into, and the
modified bitumen compound comes up through the granules to ensure proper seam
construction and adhesion.
H. All laps must be parallel or perpendicular to the slope of the roof such that the flow of water
is never against the lap.
I.
3.08
Membranes must not be applied during adverse weather or without precautionary measures
in temperatures below 45ºF (7.2ºC). Contact GAF® Contractor Services for details.
PLY LAYOUT
A. Two-ply application: Install 19 11/16” (50 cm) and 39 3/8” (100.0 cm) width starter plies, and
follow with a second 39 3/8” (100.0 cm) width sheet with a maximum of 17 11/16” (44.9 cm)
exposure, applied shingle fashion. Lap felts 20 11/16” (52.6 cm) with an 18 11/16” (47.5
cm) exposure and 6” (15.2 cm) on end laps. Stagger adjacent end laps a minimum of 18”
(45.7 cm).
3.09
BITUMINOUS BASE FLASHINGS
A. Install GAF® base flashing specification ___________ over all cant strips, horizontal to
vertical transitions, roof edges and roof penetrations. Flashings are to be secured in
accordance with current GAF® application guidelines.
B. Nailable curbs and walls must be covered with a layer of approved GAFGLAS Base Sheet
or backer ply fastened 8” (20.3 cm) o.c. in all directions with approved fasteners. All vertical
laps shall be 4” (10.2 cm). Base sheet or backer ply must extend out onto the field of the
roof as shown in the applicable GAF® construction detail.
C. Prime all metal and masonry surfaces with asphalt primer, and allow adequate drying time
prior to adhering flashing plies.
D. Backer plies installed over masonry or other non-nailable substrates must be cut into
manageable lengths to ensure adequate adhesion to the cant strip and vertical surfaces
without excessive voids. All vertical laps shall be 4” (10.2 cm). Backer plies shall extend
onto the field of the roof as shown in the applicable GAF® construction detail.
E. The finished ply of base flashing shall be run vertically to provide a selvage edge that will aid
in achieving proper adhesion at the 3” (7.6 cm) vertical laps. If the sheet is run horizontally,
07550-10
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
the vertical laps must be a minimum of 6” (15.2 cm) and the selvage edge must be removed
form the sheet or fully covered by the counterflashing. The finished flashing ply must extend
out onto the field of the roof as shown in the applicable GAF® construction detail, and must
be extended a minimum of 4” (10.2 cm) beyond the edge of the prior flashing plies. The
flashing must be soundly adhered to the parapet, cant area and roof surface to result in a
minimum void, non-bridging construction.
F. Base flashing heights must be a minimum of 8” (20.3 cm) and a maximum of 24” (61.0 cm)
above the roofline.
G. Corner membrane flashings, such as “bow ties” for outside corners and “footballs” for inside
corners or other membrane reinforcements are required to ensure that base flashing corners
are sealed at cant areas. An alternate method of corner reinforcing is to install a smooth MB
membrane reinforcement piece on the prepared corner substrate prior to final surfacing
membrane. Refer to MB Flashing Details section of the GAF® Application and
Specifications Manual.
3.10
SHEET METAL
A. Metal should not be used as a component of base flashing. Because of the high coefficient
of expansion of sheet metals and the large temperature changes that can be experienced
on a roof, sheet metal or exposed metal components must be isolated from the
waterproofing components of the roofing and flashing system as efficiently as possible to
prevent the metal from splitting the membranes. GAF® assumes no responsibility for
damage to the roofing system caused by the movement of accessory metal.
B. When it is unavoidable to use metal in the roofing system (i.e., lead flange at drains, gravel
stops), treated wood nailers and insulation stops, 1” (25 mm) wider than the metal flange,
should be provided for metal flange attachment. Metal flanges must always be set on top of
the roof membrane with modified trowel grade cold adhesive applied material for SBS roof
systems. The metal flange is then sealed using the applicable construction detail to meet
applicable guarantee requirements. Metal accessories (gravel stops, counter flashing, etc.)
should be 16 oz. (0.56 mm) copper, 24 gauge (0.71 mm) galvanized or stainless steel, 2 1/2
to 4 lb (1.1-1.8 kg) lead, or 0.032” (0.81 mm) aluminum.
C. Fabricate and install all sheet metal materials as shown in applicable construction details.
Refer to SMACNA (Sheet Metal and Air Conditioning Contractors National Association, Inc.)
for guidance on sheet metal treatments not addressed in this specification.
D. Clean metal and apply asphalt primer to all sheet metal surfaces that will come into contact
with asphalt or other bituminous materials; allow the primer adequate time to dry.
E. Use fastener types compatible with the sheet metal type.
1. Copper or lead-coated copper: use copper or bronze fasteners.
2. Lead and galvanized steel: use galvanized or cadmium-plated sheet fasteners.
3. Aluminum: use aluminum fasteners.
4. Stainless steel: use stainless steel fasteners.
F. Metal counter-flashing shall have a minimum 4” (10.2 cm) face with a drip lip. The bottom
edge of the counterflashing shall cover the roofing membrane and/or base flashing by a
07550-11
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
minimum of 4” (10.2 cm). Metal counter flashing used for masonry walls, wooden walls, or
through wall metal flashings should be a two piece design to allow for installation and later
removal. Metal counter-flashings for stucco, EIFS, wood siding or similar materials should
be designed appropriately, such as “Z” type flashing. End joints shall be lapped 3” (7.6 cm)
or more. Adequate fasteners must be provided to secure against wind forces. Skirt fasteners
shall be watertight.
G. Metal termination bars shall be a minimum of 1/10” (3 mm) thick x 1” (25 mm) wide with
preformed sealant edge lap. Bar should have 1/4” (6 mm) x 3/8” (10 mm) slotted holes on 4”
(10.2 cm) centers to facilitate mechanical anchorage.
Note: Termination bars are not suitable in all base flashing and wall flashing conditions.
Termination bars may only be used in conjunction with an appropriate counter-flashing
extending a minimum of 4” (10.2 cm) below the termination bar.
H. Metal flanges for gravel stops, eave strips, and pitch pockets to be used in conjunction with
roofing shall be primed (both sides), set in modified trowel grade cold adhesive applied
material for SBS roof systems. Flanges shall be a minimum of 3 1/2” (8.9 cm) wide for
gravel stops or eave strips and 4” (10.2 cm) wide for projections and extensions through the
roof. The gravel stop lip should be at least 3/4” (19 mm) high. Eave strip lips shall be at least
3/8” (10 mm) high. Provisions must be made for securing the skirt to the face of the wall.
This may be a wood nailer strip for masonry and metal construction. In all cases, gravel stop
and eave strip nailer should be fastened to the deck or deck system with adequate
resistance against wind forces.
I.
Stacks shall have metal sleeve flashing a minimum of 8” (20.3 cm) high. Pitch pockets for
brackets, supports, pad-eyes, etc., shall have a 4” (10.2 cm) minimum height metal sleeve.
J. On re-roofing projects, provisions shall be made for reinstallation of existing sheet metal
duct work, equipment, coping metal and counter-flashing removed in conjunction with the
new work. Also, provide for cleaning and repairing of existing defective sheet metal, and
replacement of missing and irreparable sheet metal to match existing types. Light gauge
sheet metal flashings which are incorporated into the Ruberoid® roof system are not
suitable for re-use and must be replaced with new material.
K. Conduits and piping such as electrical and gas lines must be set on wood blocking or some
other form of support. Wood blocking/supports must be set on pads constructed of an
additional layer of roof membrane material.
3.11
WALKWAYS
A. Walkways for normal rooftop traffic may be constructed from two plies of modified
bituminous membrane of the same type as the field of the roof. This type of walkway is not
for sidewalk or patio-type use.
B. Construct walkways by solidly adhering a first ply of smooth surfaced membrane to the field
of the roof followed by a granule surfaced membrane to the surface of the first ply.
C. Walkway sections should be no longer than 10’ (3 m), with a 6” (15.2 cm) minimum gap
between each section to allow for drainage.
07550-12
Rev 06/13
GAF® RUBEROID® GUIDE SPECIFICATION
NN-1-1-TGPFREC
3.12
ROOF PROTECTION
A. Protect all partially and fully completed roofing work from other trades until completion.
B. Whenever possible, stage materials in such a manner that foot traffic is minimized over
completed roof areas.
C. When it is not possible to stage materials away from locations where partial or complete
installation has taken place, temporary walkways and platforms shall be installed in order to
protect all completed roof areas from traffic and point loading during the application process.
D. Temporary tie-ins shall be installed at the end of each workday and removed prior to
commencement of work the following day.
3.13
CLEAN-UP
A. All work areas are to be kept clean, clear and free of debris at all times.
B. Do not allow trash, waste, or debris to collect on the roof. These items shall be removed
from the roof on a daily basis.
C. All tools and unused materials must be collected at the end of each workday and stored
properly off of the finished roof surface and protected from exposure to the elements.
D. Dispose of or recycle all trash and excess material in a manner conforming to current EPA
regulations and local laws.
E. Properly clean the finished roof surface after completion, and make sure the drains and
gutters are not clogged.
F. Clean and restore all damaged surfaces to their original condition.
END OF SECTION
07550-13
Rev 06/13