WOODWORK 6030
GCE O Level
FOR EXAMINATION IN 2008
Exclusions
This syllabus must not be offered in the same session with the following syllabus:
0632 Design and Realisation (Woodwork) (Namibia)
You can find syllabuses and information about CIE teacher training events on the CIE
Website (www.cie.org.uk).
www.XtremePapers.net
www.XtremePapers.net
WOODWORK 6030 O LEVEL 2008
WOODWORK
GCE Ordinary Level/School Certificate
Subject 6030
This syllabus is available for examination in November only.
Copies of syllabuses, past papers and Examiners’ Reports are available on CD ROM and can be
ordered using the Publications Catalogue, which is available at www.cie.org.uk under
‘Qualifications & Diplomas’ – ‘Order Publications’.
INTRODUCTION
The syllabus is concerned with giving the opportunity to develop a range of practical drawing
and woodworking skills and understanding of associated materials, tools and techniques.
1
AIMS
The aims set out the purpose of a course in preparation for the ordinary level GCE
examination in woodwork. The aims are not listed in order of priority.
The aims are to:
1.1
Develop practical skills to manipulate wood and make constructions
1.2
Develop graphical skills including free hand sketching and measured drawing
1.3
Establish a capacity to read and interpret formal technical drawings and diagrammatic
illustrations
1.4
Acquire a body of knowledge to inform practical work and give a broad understanding of
wood based products
1.5
Nurture a safe approach to practical work with materials and tools
1.6
Promote a capacity to solve specified technical design problems
2
ASSESSMENT OBJECTIVES
The objectives, which are not listed in order of priority, describe what a candidate should be
able to do at the culmination of the course.
Candidates should be able to:
2.1
Describe materials, tools and processes associated with the use of a range of common
soft woods, hard woods, manufactured boards and laminates
2.2
Apply knowledge of materials, tools and processes to explain choice of material,
construction, fixings and methods of working
2.3
Read and interpret drawings conforming to standard practice
2.4
Illustrate concepts, processes and technical detail by free hand sketches and projected
measured drawings
2.5
Solve specified technical design problems by completing given but incomplete solutions
2.6
Provide solutions to simple design problems
2.7
Describe and implement appropriate safe working methods
2.8
Make an artefact or part artefact in wood to a working drawing using a range of
processes including marking out, cutting, shaping, joining, fixing and finishing
www.XtremePapers.net
1
WOODWORK 6030 O LEVEL 2008
3
SCHEME OF ASSESSMENT
3.1
Examination components
Title
Duration
Weighting
1
Theory, Drawing and
Design
2 hours 45 minutes
50%
2
Practical test
3 hours
50%
Component
number
3.2
Component 1
Theory, Drawing and Design (2hrs 45 mins,100 marks)
The question paper will have two sections.
Section I Theory
This will have two parts - A and B. Candidates are expected to spend not more than
35 minutes on each part A and B (ie 1 hour 10 minutes total on Section I).
Part A will have short answer questions, all of which are to be answered on the
examination paper.
Part B will have four questions requiring longer answers from which candidates are
required to select and answer two.
Questions in Section I will be drawn from across the syllabus. Sketches will be required
to be included in response to some questions.
Section II Drawing and Design
An incomplete solution to a design situation will be given for the candidate to complete.
There will be two related parts. The first will require the candidate to show design ideas
for completing the design by free hand sketches and added notes. The second will
require formal measured drawings of the complete solution using their preferred choice
of 1st or 3rd angle orthographic projection. Questions will be presented in 1st angle,
isometric, or oblique projection or a combination of these.
Candidates will be informed of the general focus of the questions about three weeks
before the date of the examination.
3.3
Component 2
Practical test (3hrs,100 marks)
Materials will be prepared before the examination. Candidates will be required to mark out,
and make a construction which will normally be based on part of a piece of furniture. The
test will normally include one or more jointing methods listed in section 4.4 and will usually
involve the solving and provision of an unspecified construction within the test piece.
www.XtremePapers.net
2
WOODWORK 6030 O LEVEL 2008
4
SYLLABUS CONTENT
Students should be able to:
4.1
Drawing and Design
Read and interpret working drawings complying with standard practice*.
Make measured projected drawings using either 1st angle or 3rd angle projection and
construct simple scales for making drawings to scale. Use centre lines, hidden detail and
make sections parallel to horizontal or vertical planes.
Make freehand sketches to communicate design ideas, construction methods, and help
describe processes.
Design components and detail parts to complete a specified but incomplete design.
Typically this might be a small cabinet for which a door or drawer must be added.
Show an ability to make decisions regarding general proportions, choice of construction,
contour and surface finish and decoration.
4.2
Materials
Describe:
4.3
•
basic characteristics of soft and hard wood, plywood, laminated boards, hardboard,
and plastic faced boards in common use and their suitability for particular purposes.
•
the growth, conversion and seasoning of timber and its behaviour during seasoning.
•
common defects such as shakes, splits, and those created by pests.
•
simple methods for testing:
moisture content by comparative and experimental methods but excluding
chemical and electrical techniques
mechanical strength along and across the grain, resistance to bending of
simple supported beams (e.g. shelf)
comparative density.
Preparation and marking.
Prepare timber to size.
Use face side and edge as datums.
4.4
Construction
Describe and cut appropriate joints from the following for box, frame, carcass
(including drawer) constructions:
•
halvings
- simple and dovetail
•
mortise and tenon
- through, stopped, haunched (with and without
groove),
long and short shouldered (without mouldings)
•
housings
- through, stopped and simple dovetail
•
bridle
- simple, dovetailed
•
dovetail
- common, lapped
www.XtremePapers.net
3
WOODWORK 6030 O LEVEL 2008
4.5
Fitting, fixing and adhesives
Describe the use of:
4.6
•
adhesives for wet and dry conditions.
•
screws, nails, common furniture hardware and fittings including magnetic and
nylon door catches and hinges.
Surface finish
Describe and use:
4.7
•
veneer on flat surfaces.
•
abrasive paper/cloth for smoothing.
•
wood preservative, paint, stains and polish including water repellent and heat
resistant finishes.
Tools
Identify and describe common woodworking tools and explain their use, care and
maintenance.
4.8
Supplementary
Show awareness of woodworking in a broader context than cabinet making, e.g. free
form and sculpture work, lathe turning, and simple boat building.
4.9
Safety
Use and explain safe working methods and precautions applicable to processes
identified in the syllabus.
*
Engineering Drawing Practice for Schools and Colleges. British Standards Institution
(PP 7308.)
Notes
1
Recent past examination question papers may be used as specimen papers
2
Metric units will be used in examination questions
3
Reports on the work of candidates are published after each examination
4
Instructions about materials and equipment requirements for an examination are issued
before each examination
www.XtremePapers.net
4