Data Sheet MEPKPFENa
PhotoKleenTM PF Filter Capsule
Description
The PhotoKleen PF filter is designed for extremely small-volume dispense applications where low hold-up volume and
cleanliness is critical. The PhotoKleen PF filter unit consists
of quick disconnect head manifold and the all fluoropolymer
capsule. This configuration allows for safe, quick and easy
filter change-outs. Cleanliness and compatibility are ensured
by the all fluoropolymer construction.
Features and Benefits
• Capsule-style filter assembly same as the PhotoKleen
EZD-2 filter
• Top in / top out flow direction, with inlet flow stream
down to the bottom
• Easy filter replacement (one step)
• All fluoropolymer construction
• PTFE media 0.1 and 0.2 µm grade available
• Minimized hold-up volume (50 mL)
• Optimized for 60 mm-width footprint
• Reduces chemical waste during filter startup and
change out
PhotoKleen PF Filters are designed to fit into all PhotoKleen
EZD-2 series head manifolds.
Specifications
Materials of Filter Capsule
Components
Materials
Removal Ratings
0.1 µm, 0.2 µm
Filter Media
PTFE
Filter Area
900 cm2
Support and Drainage
PFA
Maximum Operating
Temperature
50 ˚C / 122 ˚F
Core, Cage, and End Caps
PFA
Housing
PFA
Maximum Operating
Pressure
0.29 MPaG @ 30 ˚C / 42 psig @ 86 ˚F
O-ring
Kalrez *1
*1
Kalrez is a trademark of DuPont.
Pressure Drop vs. Liquid Flow Rate (Water, 20℃)*2
Clean Pressure Drop (kPa)
2.5
2
FT
1.5
FR
1
0.5
0
*2
0
50
100
150
Liquid Flow Rate (mL / min), 1 mPa･s Fluid
200
For liquids with viscosity differing from water, multiply the pressure drop by the viscosity in mPa･s.
Filter Capsule Dimensions*3
(73.5)
24
(73.5)
20
24
(63.35)
(63.35)
(∅55)
(∅55)
∅19
VENT
3.5
(∅50.7)
(∅50.7)
PhotoKleen EZD-2 head manifolds are compatible with PhotoKleen PF capsules.
Part Numbers / Ordering Information
PHF12UC
1
E
2
Table 1
Code
FT
FR
Table 2
Filter Media
PTFE
INLET
(72.15)
OUTLET
(72.25)
INLET
Removal Ratings
Code
O-ring Options
0.1 µm
H11
Kalrez
0.2 µm
Dummy Cartridge
Parts Number
O-ring Options
Memo
PHFC11H11C
Kalrez
Dummy cartridge for system start up
3.5
∅19
*3
20
OUTLET
VENT
Microelectronics
25 Harbor Park Drive
Port Washington, NY 11050
+1 800 360 7255
toll free US
+1 516 484 3600
telephone
+1 516 801 9711
fax
microelectronics@pall.com
Nihon Pall Ltd.
6-5-1, Nishishinjuku,
Shinjuku-ku
Tokyo 163-1325 Japan
+81 3 6901 5700
telephone
+81 3 5322 2109
fax
Visit us on the Web at www.pall.com/micro
Pall Corporation has offices and plants throughout the world. For Pall representatives in your
area, please go to www.pall.com/corporate_contact.asp.
Because of technological developments related to the products, systems, and/or services
described herein, the data and procedures are subject to change without notice. Please consult your Pall representative or visit www.pall.com to verify that this information remains valid.
Products in this document may be covered by one or more
of the following patent numbers: US5543047; US5690765; US6113784; US7083564; US7318800;
EP0982061; EP0667800; EP1380331.
© Copyright 2016, Pall Corporation. Pall,
, and PhotoKleen are trademarks of Pall Corporation.
® Indicates a Pall trademark registered in the USA.
is a service mark of Pall
Corporation.
MEPKPFENa
April 2016