Respond & Achieve
Hytera Patrol System Tutorial
www.hytera.com
01
03
System
Overview
System
Config
02
04
Network
Structure
Software
Installation
01
System
Overview
System Overview
Receiving Station: A repeater (RD62X/RD96X/RD98X/RD98XS) or a mobile
radio (only MD78X) can work as a patrol data receiving station.
System Components
Item
Power Supply
Working
Temperature
Frequency
Valid
Distance
Patroller ID Card
No extra power
supply
-22~55℃
13.56~14.2Mhz
3 cm
Patrol Checkpoint No extra power
supply
-40~85 ℃
13.56~14.2Mhz
4 cm
UHF: 400-470Mhz
4W(High); 1W(Low)
VHF: 136-174Mhz
5W(High); 1W(Low)
16 Hours (1500mAh); 22 Hours (2000mAh)
U.S.A Military Standard & IP54
Analog & Digital auto detect
PD41X
Patrol Radio
Embedded RFID
Up to 250 pieces of offline data could be stored
02
Network
Structure
Single Site Solution
Multi-sites Solution
03
System
Config
Mobile Receiving Station Config
Forward To PC
Step 1 Go to “Conventional -> General Setting -> Network” from the left
navigation tree of CPS.
Step 2 Select Forward To PC in Radio to PC Network interface.
Mobile Receiving Station Config
Channel Configuration
Step 1 Go to “Conventional -> Channel -> Digital Channel” from the left
navigation tree of CPS,right click Digital Channel and select Add to
add a new digital channel.
Mobile Receiving Station Config
Channel Configuration (Continued)
Step 2 Double-click the new digital channel to enter the configuration
interface. Configure the channel alias per configuration planning
and select a slot (etc. Slot1) in Slot Operation.
Set the Receive Frequency and Transmit Frequency.
Mobile Receiving Station Config
Channel Configuration (with Pseudo Trunk feature)
If Mobile Radio Receiving Station Solution uses only one frequency, the Pseudo
Trunk feature must be enabled; the slot for patrolling services must be different
from the slot for voice communication; RX Group List and TX Contact must be set
to None.
Mobile Receiving Station Config
Radio ID
Go to “Conventional -> DMR Services -> Basic” or “Conventional -> Digital
Common -> Basic” to set the Radio ID of the Mobile Radio Receiving Station.
Mobile Receiving Station Config
TMS Port
Go to “Conventional -> General Setting -> Network -> Radio Services” and set
“TMS Port” to “5016”.
Repeater Configuration
Single site Network
Step 1 Go to “Conventional -> General Setting -> Network” from the left
navigation tree of CPS and configure the following parameters.
Repeater Configuration
Single site Network (Continued)
Step 2 Select “Single Site” for local operation
Step 3 Click “Forward to PC”
Step 4 Enter the client computer IP address into “Third Party Server IP”.
Repeater Configuration
Multi-sites IP Connection (Master)
Step 1 Go to “Conventional -> General Setting -> Network” from the left
navigation tree of CPS and configure the following parameters.”.
Repeater Configuration
Multi-sites IP Connection (Master)
Step 2 Select “Master”. The repeater will operate locally; it will not send data to other
repeaters; patrol data will be uploaded to the client.
Repeater Configuration
Multi-sites IP Connection (Slave)
Step 1 Set repeater IP address into the same LAN of Third Party Server IP.
Repeater Configuration
Multi-sites IP Connection (Slave)
Step 2 Select “Slave”. The repeater will send patrol data to “Master” via Ethernet.
Notice: Unclick “Forward to PC” box of “Slave” repeater.
Repeater Configuration
Channel Configuration
Step 1 Go to “Conventional -> Channel -> Digital Channel” from the left
navigation tree of CPS,right click Digital Channel and select Add to
add a new digital channel.
Repeater Configuration
Channel Configuration (Continued)
Step 2 Double-click the new digital channel to enter the configuration
interface. Configure the channel alias per configuration planning
and select a slot (etc. Slot1) in Slot Operation..
Notice:
If the voice service and patrolling service shares the same frequency, different slots
must be used. For example, the patrolling service uses slot 1 while the voice service
uses slot 2
Repeater Configuration
Channel Configuration (Continued)
Step 3 Go to “Conventional -> Zone” from the left navigation tree of the
CPS, select the “Digital patrol channel” and click “Add” to add it to
the last channel in “Member” list.
Repeater Configuration
Radio ID
Go to “Conventional -> DMR Services -> Basic” or “Conventional -> Digital
Common -> Basic” to set the Radio ID of the Mobile Radio Receiving Station.
Portable Radio Configuration
Radio Contact
Go to “Conventional -> DMR Services -> Contact” from the left navigation tree of
the CPS, add the Alias and ID of the repeater or Mobile Radio Receiving Station
into the list and set the Call Type to Private Call.
Portable Radio Configuration
Channel Configuration
Step 1 The necessary parameters need to configure including: “Slot Operation”,
“Receive Frequency”, “Transmit Frequency” and “Tx Contact Name” . The Tx admit
of patrolling service channel should be set to “Channel Free”; “TDMA Direct Mode”
must be selected.
Portable Radio Configuration
Channel Configuration (Continued)
Step 2 Go to “Zone -> Zone 1” from the left navigation tree of the CPS,
select the Digital patrol channel and click “Add” to add it to the
last channel in Zone 1.
Notice:
For Patrol Management System, the patrolling data of patrol portable radios are
automatically switched and transmitted in the last digital channel of the current
zone by default. Otherwise, the patrolling data cannot be uploaded successfully
Portable Radio Configuration
Patrol Emergency
Go to “General Setting -> Buttons” from the left navigation tree of the
CPS, select Patrol Emergency from the drop down list for SK1 or SK2
In case of emergency during patrolling, the patroller can press the programmed
Patrol Emergency key to trigger the emergency alarm.
Portable Radio Configuration
Patrol Resend
Go to “General Setting -> Buttons” from the left navigation tree of the
CPS, select Patrol Resend from the drop down list for SK1 or SK2.
In case of patrol data uploading failure during patrolling, the patroller can
press the programmed Patrol Resend key to resend the data.
04
Software
Installation
Software Installation
Hardware Devices Requirements
Downloading and Unzipping Installation Package
1. Download “Hytera PD41X Patrol Management System.rar” from www.hytera.com
(Download path: Downloads -> Driver & Software -> PD41X).
2. Unzipping the installation package into a chosen folder.