8464
846410
846420
846490
machine tools for working stone, etc & glass
Sawing Machines for Working Mineral Materials
Grinding or Polishing Machines for Working Mineral Materials
Machine-tools for Working Mineral Materials or for Cold Working
Glass
American Standards
ASME B107.51-2001, Star Drills - Safety
Requirements
Provides safety requirements for the design,
construction, testing and use of hand-held star
drills. These hand-held star drills are intended
for use in drilling holes in brick, tile, concrete, or
stone.
Single copy price: $10.00
Order from: Silvana Rodriguez-Bhatti, ASME
Send comments (with copy to BSR) to: James
Bird, M/S 20S2, ASME
ANSI B11.10-2003, Metal Sawing
Machines, Safety Requirements for
Construction, Care, and Use of
Covers the safety requirements as they relate
to the design, installation, safeguarding,
operation and maintenance of powered
machines used to saw metals.
ASME B107.4M-2005, Driving and Spindle
Ends for Portable Hand, Air, and Electric
Tools
Applies to portable power tools for drilling,
grinding, polishing, sawing, and driving
threaded fasteners and hand tools for driving
threaded fasteners. Other tools not classified
as percussion tools belong in this category and
may be added by revision or addition through
the usual procedure. This Standard includes
dimensions and tolerances for both driving and
driven elements where such coordination is
important and not established by reference to
the pertinent American National Standards. All
dimensions are in inches and millimeters.
ANSI B212.9-1994 (R2005), Cutting Tools Carbide Blanks for Tipping Circular Saws
Covers dimensional specifications and
designation for carbide blanks for tipping
circular saws. The values stated in US
customary units are to be regarded as the
standard.
ANSI B175.1-2000, Gasoline Powered
Chain Saws, Safety Requirements for
Establishes safety requirements for the
manufacture and use of portable, hand-held,
gasoline-powered chain saws. It contains
definitions of terms relevant to chain saws and
their use, and guidelines for certain chain saw
features. The standard also contains test
procedures and specific performance
requirements concerning vibration, sound
levels and bar nose kickback.
UL 60745-2-11-2004, Standard for Safety
for Hand-Held Motor-Operated Electric
Tools - Safety - Part 2-11: Particular
Requirements for Reciprocating Saws
This International Standard deals with the
safety of hand-held motor-operated or
magnetically driven electric tools, the rated
voltage of the tools being not more than 250 V
for single-phase a.c. or d.c. tools, and 440 V for
three-phase a.c. tools. This standard applies to
reciprocating saws (jig and sabre saws).
UL 60745-2-20-2005, Standard for Safety
for Hand-held Motor-operated Electric
Tools - Safety - Part 2-20: Particular
Requirements for Band Saws
This bulletin proposes the following changes in
requirements: Proposed First Edition of the
Standard for Hand-Held Motor-Operated
Electric Tools – Safety – Part
2-20: Particular Requirements for Band Saws,
UL/CSA 60745-2-20.
UL 60745-2-5-2004, Standard for handheld
Motor-Operated Electric Tools - Safety Part 2: Particular Requirements for
Circular Saws
Editorial Changes to the Third Edition of UL
60745-1 and UL 60745-2-5; and the Second
Edition
of UL 60745-2-1, UL 60745-2-6, UL
60745-2-14, and UL 60745-2-17. These
changes modify
proposed requirements from the following
bulletins:
July 31, 2002
September 6, 2002
January 3, 2003
April 7, 2003
ASME B107.4M-2005, Driving and Spindle
Ends for Portable Hand, Air, and Electric
Tools
Applies to portable power tools for drilling,
grinding, polishing, sawing, and driving
threaded fasteners and hand tools for driving
threaded fasteners. Other tools not classified
as percussion tools belong in this category and
may be added by revision or addition through
the usual procedure. This Standard includes
dimensions and tolerances for both driving and
driven elements where such coordination is
important and not established by reference to
the pertinent American National Standards. All
dimensions are in inches and millimeters.
ANSI B11.9-1975 (R2005), Safety
Requirements for the Construction, Care,
and Use of Grinding Machines
This standard applies only to grinding
machines, designed primarily for metal
removal, that present grinding tools against
workpieces, producing change in shape, size,
and surface finish by grinding. This standard
also applies to these machines when they are
grinding materials other than metals such as
glass, ceramics, plastics, and rubber.
UL 745-2-3-2006, Standard For Safety For
Particular Requirements for Grinders,
Polishers and Disk-Type Sanders
First Edition of the Standard for Particular
Requirements for Grinders, Polishers and
Disk-Type Sanders, UL 745-2-3, as an
American National Standard.
International standards
IEC 60745-2-3 Ed. 2.0 b:2006
"Hand-held motor-operated electric tools - Safety Part 2-3: Particular requirements for grinders,
polishers and disk-type sanders"
IEC 61029-2-10 Ed. 1.0 en:1998
Safety of transportable motor-operated electric
tools - Part 2-10: Particular requirements for
cutting-off grinders
ISO Standards
ISO 8662-14:1996
Hand-held portable power tools - Measurement of
vibrations at the handle - Part 14: Stone-working tools
and needle scalers
Indian Standards
IS 1249 :
1997
Recommendations for selection of grinding wheels
Active
IS 1991 :
Part 1 :
1987
Safety requirements for the use, care and protection of abrasive
grinding wheels:Part 1 Definitions
Active
IS 1991 :
Part 2 :
1987
Safety Requirements for the Use, Care and Protection of Abrasive
Grinding Wheels Part 2 : Handling and Storage
Active
IS 1991 :
Part 3 :
1987
Safety Requirements for the Use, Care and Protection of Abrasive
Grinding Wheels - Part 3 : General Machine Requirements
Active
IS 1991 :
Part 4 :
1988
Safety requirements for the use, care and protection of abrasive
grinding wheels:Part 4 Safety guards
Active
IS 1991 :
Part 5 :
1987
Safety requirements for the use, care and protection of abrasive
grinding wheels:Part 5 Flanges
Active
IS 1991 :
Part 6 :
1987
Safety Requirements for the use, care and protection of abrasive
grinding wheels:Part 6 Inspection and mounting
Active
IS 1991 :
Part 7 :
1987
Safety requirements for the use, care and protection of abrasive
grinding wheels:Part 7 Standard speeds
Active
IS 1991 :
Part 8 :
1987
Safety requirements for the use, care and protection of abrasive
grinding wheels:Part 8 Special speeds
Active
IS 1991 :
Part 9 :
1987
Safety requirements for the use, care and protection of abrasive
grinding wheels:Part 9 General operating rules
Active
IS 1991 :
Part 10 :
1987
Safety requirements for the use, care and protection of abrasive
grinding wheels:Part 10 Mounted wheels
Active
IS 2324 :
Part 1 :
1985
Bonded abrasive grinding wheels:Part 1 Profiles and types
Active
IS 2324 :
Part 2 :
1985
Bonded Abrasive Grinding Wheels - Part 2 : Dimensions
Active
IS 2368 :
1993
Test Charts for External Cylindrical Grinding Machines with a
Movable Table
Active
IS 2743 :
1992
Test chart for surface grinding machines with horizontal grinding
wheel spindle and reciprocating table
Active
IS 2996 :
1986
Mounting dimensions of plain grinding wheels by means of hub
flanges
Active
IS 3264 :
1985
Specification for Diamond or Cubic Boron Nitride Abrasive Grinding
Active
Wheels
IS 3612 :
1994
Crushing and grinding equipment - Classification and methods for
measuring capacity
Active
IS 7157 :
1987
Specification for Portable Pneumatic Grinding Machines
Active
IS 7301 :
1974
Specification for Grinding Mandrels
Active
IS 9291 :
1979
Dimensions of internal grinding wheels
Active
IS 9809 :
Test chart for crankshaft grinding machines
Active
1981
IS 10352 : Test Charts for Internal Cylindrical Grinding Machines with
1992
Horizontal Spindle
Active
IS 10874 :
Specification for Felsite Grinding Media and Liner Stones
1983
Active
IS 11522 : Recommendations for basic quantities in cutting and grinding Part 1 :
Part 1 :
Geometry of the active part of cutting tools, general terms, reference Active
1986
systems, tools & working angles and chip breakers
IS 12295 : Acceptance Conditions for External Cylindrical Centreless Grinding
Active
2000
Machines - Testing of the Accuracy
IS 13552 : Test charts for surface grinding machines with vertical grinding
1992
wheel spindle and reciprocating table
Active
IS 13934 : Test charts for surface grinding machines with two columns for
1994
grinding slideways
Active
IS 15299 : Machine Tools - Mounting of Plain Grinding Wheels by Means of
2002
Hub Flanges
Active
IS 3656 : 1968
Code of recommended practice for mechanical polishing of
Active
metals for electroplating
IS 7739 : Part 2 Code of Practice for Preparation of Metallographic
: 1975
Specimens - Part 2 Electrolytic polishing
Active
IS 10024 :
1981
Withdarwn
Jewellers polishing rouge