DRAINAGE GUTTERS FOR
DRAIN ASPHALT
2012
TECHNICAL CATALOGUE
TABLE OF CONTENTS
Drainage gutters and drain bodies
Chapter 01
Page
- Installation diagram
- Installation diagram
- Drainage gutter (cast iron) with centrical nozzle
- Drainage gutter (cast iron) with centrical nozzle
- Drainage gutter (cast iron) with front side nozzle
- Drainage gutter (cast iron) with front side nozzle
- Drainage gutter (stainless steel), width 170 mm
- Drainage gutter (stainless steel), width 170 mm
- Drainage gutter (stainless steel), width 300 mm
- Drainage gutter (stainless steel), width 300 mm
- Base parts
- Figures of stainless steel gutters
02
04
05
06
07
08
09
10
11
12
13
14
15
Subject to technical changes - © with Höllko®
DRAINAGE GUTTERS
INSTALLATION DIAGRAM
SYSTEM DESCRIPTION
03
drainage gutters installation diagram
FIGURE 1
Höllko offers two different systems of
drainage gutters. The variant made of
stainless steel (see figure 1) is basically
produced without slope. Therefore, it must be
installed by the customer at a slope angle
of at least 2%.
FIGURE 2
In order to position the gutter,
an installation and adjustment
aid is required, for example
the wooden structure shown
on the left. Figure 2 shows an
adjusted cast iron gutter.
04
Subject to technical changes - © with Höllko®
drainage gutters installation diagram
STAINLESS STEEL
GUTTER
5
1
2
4
3
6
1
2
3
4
5
6
ROAD SURFACE MADE OF DRAIN ASPHALT
INTERMEDIATE LAYER MADE OF MASTIC ASPHALT
PROTECTIVE LAYER MADE OF MASTIC ASPHALT
WATER-PERMEABLE REACTION RESIN CONCRETE
WITH EPOXY RESIN BINDER
SEALED JOINTS
SEALING LAYER
CAST IRON GUTTER
5
1
2
3
4
Subject to technical changes - © with Höllko®
6
05
Product description/tender specification
Drainage gutter made of cast iron with 130 drainage holes laterally on the
roadway side (ø 20mm)
Gutter length 3950mm, width 330mm, height 138mm with 2 fix and 3 hinged
grids (L = 800mm), slot width 30mm, with hinge and friction lock
(square 14mm made of stainless steel)
DIN EN 124/1229, test load class D 400, material GGG (spheroidal cast iron)
slope (2 %) towards the centre on both sides
Outer pipe diameter nozzle = 150mm (200mm)
Inlet cross section grid 5160cm²
Inlet cross section drainage openings 408cm²
Installation option:
- As gutter system individually or connected to each other
TOP VIEW
3950
290
138
SECTION
2%
ND 150
VIEW
06
Subject to technical changes - © with Höllko®
drainage gutters made of cast iron
Drainage gutter made of cast iron
ND
Length mm
kg
Item no.
150
3950
480
ER1100DN150SM
200
3950
480
ER1100DN200SM
71710
Ordering notes:
330
Base parts on page 14
Sludge traps and adapters upon request
CROSS-SECTION
100
330
2%
Subject to technical changes - © with Höllko®
50
Ø2
50
0
47
DETAIL
07
Product description/tender specification
Drainage gutter made of cast iron with 130 drainage holes laterally on the
roadway side (ø 20mm)
Gutter length 3950mm, width 330mm, height 138mm with 2 fix and 3 hinged
grids (L = 800mm), slot width 30mm, with hinge and friction lock
(square 14mm made of stainless steel)
DIN EN 124/1229, test load class D 400, material GGG (spheroidal cast iron)
Outer pipe diameter nozzle = 150mm (200mm)
Inlet cross section grid 5160cm²
Inlet cross section drainage openings 408cm²
Installation option:
- As gutter system individually or connected to each other
TOP VIEW
3950
SECTION
VIEW
08
Subject to technical changes - © with Höllko®
drainage gutters made of cast iron
Drainage gutter made of cast iron
ND
Length mm
kg
Item no.
150
3950
480
ER1100DN150SS
200
3950
480
ER1100DN200SS
71710
Ordering notes:
330
Base parts on page 14
Sludge traps and adapters upon request
CROSS-SECTION
250
100
330
ND 150
Subject to technical changes - © with Höllko®
50
Ø2
50
0
47
DETAIL
09
drainage gutters made of stainless steel
Product description/tender specification
Drainage gutter made of stainless steel with 20 vertical drainage
openings (per running metre) attached laterally (on the roadway side) (slot 43x8mm)
Suitable for drain asphalt, material thickness 4mm, grid with mesh width 21 x 21mm
Number and size variable, DIN EN 1433, test load class D 400
Material stainless steel 1.4404 / 1.4571
Drain nozzle ND 100 (ND150), position drain nozzle variable
Flange or plug-and-socket connection
Standard lengths 1000mm, 2000mm, 3000mm, 6000mm, as well as adapters as required
Width 170mm, height 74mm
Grids screwed 4 times
Inlet cross section grid (running metre) 1165cm²
Inlet cross section drainage openings 69cm²
- Different materials and dimensions upon request
- Optional with folding grids
TOP VIEW
1000
1000
VIEW
DETAIL PLUG-AND-SOCKET
CONNECTION
TOP VIEW (enlarged)
1000
DETAIL PLUG-AND-SOCKET
CONNECTION
SECTION (enlarged)
1000
170
1000
45
1000
45
174
170
53
12
74
12
DETAIL PLUG-AND-SOCKET
CONNECTION
VIEW (enlarged)
PLUG-AND-SOCKET
CONNECTION
WITH ADHESIVE
CONCRETE ANCHOR
OPTIONAL
10
Subject to technical changes - © with Höllko®
drainage gutters made of stainless steel
Drainage gutter made of stainless steel
71710
ND
Length mm
kg per running
metre
Item no.
100
1000
22
ER1200DN100-L1000
150
1000
22
ER1200DN150-L1000
100
2000
22
ER1200DN100-L2000
150
2000
22
ER1200DN150-L2000
100
3000
22
ER1200DN100-L3000
150
3000
22
ER1200DN150-L3000
100
6000
22
ER1200DN100-L6000
150
6000
22
ER1200DN150-L6000
Ordering notes:
170
Base parts on page 14
Sludge traps and adapters upon request
DETAIL FLANGE CONNECTION
VIEW (enlarged)
1000
POSITION OF THE DRAIN NOZZLE
VARIABEL
DETAIL FLANGE CONNECTION
TOP VIEW (enlarged)
1000
DETAIL FLANGE CONNECTION
SECTION (enlarged)
DETAIL FLANGE CONNECTION
VIEW (enlarged)
210
1000
170
53
174
95
170
1000
74
1000
CONCRETE ANCHOR
OPTIONAL
Subject to technical changes - © with Höllko®
11
drainage gutters made of stainless steel
Product description/tender specification
Drainage gutter made of stainless steel with 20 vertical drainage
openings (per running metre) attached laterally (on the roadway side)
(slot 43x8mm) suitable for drain asphalt, material thickness 4mm, grid with mesh width 21 x 21mm
Number and size variable, DIN EN 1433, test load class D 400
Material stainless steel 1.4404 / 1.4571
Drain nozzle ND 150 (200), position drain nozzle variable
Flange or plug-and-socket connection
Standard lengths 1000mm, 2000mm, 3000mm, 6000mm, as well as adapters as required
Width 300 mm, height 74mm
Grids screwed 4 times
Inlet cross section grid (running metre) 2071 cm²
Inlet cross section drainage openings 69cm²
- Different materials and dimensions upon request
- Optional with folding grids
TOP VIEW
1000
1000
10
VIEW
POSITION OF THE DRAIN NOZZLE
VARIABEL
DETAIL PLUG-AND-SOCKET
CONNECTION
TOP VIEW (enlarged)
1000
DETAIL PLUG-AND-SOCKET
CONNECTION
VIEW (enlarged)
300
1000
45
1000
45
174
53
12
74
1000
12
DETAIL PLUG-AND-SOCKET
CONNECTION
SECTION (enlarged)
300
PLUG-AND-SOCKET
CONNECTION
WITH ADHESIVE
CONCRETE ANCHOR
OPTIONAL
12
Subject to technical changes - © with Höllko®
drainage gutters made of stainless steel
Drainage gutter made of stainless steel
71710
ND
Length mm
kg per running
metre
Item no.
150
1000
43
ER1300DN150-L1000
200
1000
43
ER1300DN200-L1000
150
2000
43
ER1300DN150-L2000
200
2000
43
ER1300DN200-L2000
150
3000
43
ER1300DN150-L3000
200
3000
43
ER1300DN200-L3000
150
6000
43
ER1300DN150-L6000
200
6000
43
ER1300DN200-L6000
Ordering notes:
300
Base parts on page 14
Sludge traps and adapters upon request
DETAIL FLANGE CONNECTION
VIEW (enlarged)
1000
DETAIL FLANGE CONNECTION
TOP VIEW (enlarged)
1000
DETAIL FLANGE CONNECTION
VIEW (enlarged)
340
300
1000
300
174
95
53
1000
74
1000
DETAIL FLANGE CONNECTION
SECTION (enlarged)
CONCRETE ANCHOR
OPTIONAL
Subject to technical changes - © with Höllko®
13
BASE PARTS
Product description/tender specification
Base part made of stainless steel 1.4404 / 1.4571 for drainage gutter
with insulating flange, with concrete ring ND 100 (ND 150, ND 200)
length 500mm, wall thickness 2mm
with clamping flange and soak slots, 4-fold screw connection M10
with metal plate cover
TOP VIEW (drain body)
71710
TOP VIEW (clamping flange)
DIM. F
TOP VIEW (cover metal plate)
53
50
0
DIM. B
DIM. J
R16
T=2
32
DIM. G
DIM. B
0
DIM. G
60
Ø1
DIM. E
20
53
R1
31
151
DIM. H
DIM. A
31
53
DIM. J
SECTION (drain body)
SECTION (clamping flange)
DIM. A
80
2
DIM. B
2
SOAK SLOT
5
10
DIM. H
3
DIM. C
L
5
67 6 72
6
5
80
TOP VIEW (cover metal plate on flange)
The opening of the drain nozzle
towards the base part must be
closed by using the supplied
cover metal plate.
2
DIM. D
2
Base parts made of stainless steel
ND
Length mm
Dimension A
Dim. B Dim. C Dim. D Dim. E Dim. F Dim. G Dim. H Dim. J
Item no.
100
500
149
149
153
108
104
309
204
254
211
ERUT100
150
500
200
200
204
159
155
360
255
305
262
ERUT150
200
500
247
247
251
206
202
407
302
352
309
ERUT200
14
Subject to technical changes - © with Höllko®
FIGURES OF stainless steel gutterS
Special designs according to the customer's
specifications are possible.
The gutter bodies made of stainless steel
can be extended at the constuction site.
The type with folding grid and sludge
trap is shown here.
A connecting tunnel between the gutter pieces
may also assume a height compensation function.
Subject to technical changes - © with Höllko®
15
93183 Kallmünz, Germany
Phone +49 (0) 9473 9407 - 0
Fax +49 (0) 9473 9407 - 49
email info@hoellko.com
Internet www.hoellko.com
A branch of the Höllein group of companies.
www.hoellein-gruppe.de
THIS CATALOGUE MAY NOT BE REPRODUCED WITHOUT THE PERMISSION OF R. HÖLLEIN CAROLINENHÜTTE GMBH & CO. KG. ALL
FIGURES, DRAWINGS, AND LOGOS SHOWN ARE PROTECTED BY COPYRIGHT. THE TECHNICAL DATA IN THIS CATALOGUE IS SUBJECT
TO CHANGES. WE RESERVE ERRORS. OUR INFORMATION IS PROVIDED WITHOUT COMMITMENT AND MUST BE CHECKED IN EACH
INDIVIDUAL CASE.
DRAINAGE GUTTERS FOR DRAIN ASPHALT 2012 - DATING FROM NOVEMBER 2011.