USB-IF Product Order Form
Please use the following information to select the test hardware from the USB-IF eStore.
USB 3.1 (10 GT/s) Type-A and Micro-B Electrical Test Fixture Kit
The USB 3.1 (10 GT/s) USB Type-A and Micro-B Electrical Test Fixture Kit provides a worst case, ISI hardware
channel for PHY’s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for
either hosts or peripherals. The kit contains fifteen test fixtures, 1 meter Standard-A to Micro-B cable, one 5 Volt DC
power supply to provide V-Bus to peripherals, and a jumper (for two pin header).
Due to high demand each company is allowed a maximum order of two (2) kits at this time.
Please use product code USB31AET to order.
Member Price: $1800.00
Non-Member Price: $2200.00
Low-speed Functional Compliance Test Device
The LS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators.
Please use product code USBLSTD to order.
Member Price: $90.00
Non-Member Price: $110.00
Full-speed Functional Compliance Test Device
The FS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators.
Please use product code USBFSTD to order.
Member Price: $250.00
Non-Member Price: $300.00
USB 3.0 Electrical Test Fixture Kit
The USB 3.0 Electrical Test Fixture Kit provides a worst case, ISI hardware channel for PHY’s. It is intended to assist
companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals. This kit ships
with the necessary cables to be used in conjunction with the fixtures.
Please use product code USB3ET to order.
Member Price: $700.00
Non-Member Price: $950.00
USB 3.0 Cable Kit
The USB 3.0 Cable Kit provides five (5) SuperSpeed USB (USB 3.0) cables:
- Standard A to Standard B, 3 meter
- Standard A to Micro B, 1 meter
- Standard A to Standard B, 8 inch
- Standard A to Standard B, 4 inch
- Standard A to Micro B, 4 inch
Please use product code USB3CABLES to order.
Member Price: $150.00
Non-Member Price: $200.00
USB 2.0 Hi-Speed Signal Quality Test Fixture Set
The USB 2.0 Hi-Speed Signal Quality Test Fixtures are used for testing signal quality of hi-speed hosts and
peripherals. The fixtures eliminate the need for probes and require quality SMA cables for direct connection to the
scope. The fixtures include USB cables but do not include SMA cables.
Please use product code USB2SIGQUAL to order.
Member Price: $650.00
Non-Member Price: $900.00
Page 1 of 6
Product Order Form
Please PRINT and FAX the completed order form including payment information to the USB-IF at 503-644-6708.
Or mail with payment to:
USB Implementers Forum
3855 SW 153rd Dr.
Beaverton, Oregon 97003
Phone: 503-619-0426
The following table is for use by Members of the USB Implementers Forum only:
Company Name:
Vendor ID:
Product Code:
Description:
USB31AET
USB 3.1 USB (10 GT/s) Type-A and Micro-B
USBLSTD
Low Speed Functional Compliance Test Device
USBFSTD
Full Speed Functional Compliance Test Device
USB3ET
USB3CABLES
USB2SIGQUAL
USB 3.0 Electrical Test Fixture Kit
USB 3.0 Cable Kit
USB 2.0 Hi-Speed Signal Quality Test Fixture Set
Quantity:
Members’
Unit Price:
$1800.00 USD
$90.00 USD
$250.00 USD
Extended
Price:
$700.00 USD
$150.00 USD
$650.00 USD
Total Payment Due: 
Shipping and Handling Fees are included in the prices above.

Duties, customs and other taxes are not included within the above prices. You should
receive an invoice from the carrier and/or customs for any additional expense incurred. It
is your responsibility, and not that of USB-IF, to pay these taxes.
See next page for Non-Member pricing.
(Decimal)
Page 2 of 6
The following table is for use by Non-Members of the USB Implementers Forum:
Company Name:
Product Code:
Description:
USB31AET
USBLSTD
USBFSTD
USB3ET
USB3CABLES
USB2SIGQUAL
USB 3.1 USB (10 GT/s) Type-A and Micro-B
Low Speed Functional Compliance Test Device
Full Speed Functional Compliance Test Device
USB 3.0 Electrical Test Fixture Kit
USB 3.0 Cable Kit
USB 2.0 Hi-Speed Signal Quality Test Fixture Set
Vendor ID:
Quantity:
(Decimal)
Non-Members’
Unit Price:
$2200.00 USD
$110.00 USD
$300.00 USD
$950.00 USD
$200.00 USD
$900.00 USD
Extended
Price:
Total Payment Due: 
Shipping and Handling Fees are included in the prices above.

Duties, customs and other taxes are not included within the above prices. You should
receive an invoice from the carrier and/or customs for any additional expense incurred. It
is your responsibility, and not that of USB-IF, to pay these taxes.
Page 3 of 6
Payment information:
Please indicate the form of payment to be used. Orders will be processed upon receipt of properly completed
order form and payment in full.
Check enclosed in U.S. Funds drawn on U.S. bank, payable to: USB Implementers Forum
Wire transfer (contact admin@usb.org to request bank details)
Credit Card (complete the information below)
Card Holder Information:
Card Holder Name:
Email:
Telephone:
Fax:
Billing Address:
Mail
Stop:
City:
State/Province:
Zip / Postal Code:
Country:
Credit Card Information:
Card Type: (Please select one)

VISA

MASTERCARD
Card Number:

AMERICAN EXPRESS
Expiration:
CVV code:
(for Visa & MasterCard: 3-digit code on back of card; for American Express: 4-digit code on front of card)
Card Holder Name (As is appears on the card):
I hereby authorize the USB Implementers Forum to charge the amount of $
to the credit card listed above for this purchase.
Card Holder Signature:
Date:
Shipping Information:
Orders must contain a complete shipping address and phone numbers for items to be fulfilled. No P.O. Boxes.
Recipient's Contact Information:
Ship Attention to:
Company Name:
Address:
Mail Stop:
City:
State/Province:
Zip / Postal Code:
Country:
Email:
Telephone:
ALL PRODUCTS AND DOCUMENTS OFFERED FOR SALE BY USB-IF ARE PROVIDED "AS IS" AND WITHOUT ANY
WARRANTY OF ANY KIND, EXPRESS OF IMPLIED. WITHOUT LIMITATION, THERE IS NO WARRANTY OF NONINFRINGEMENT, NO WARRANTY OF MERCHANTABILITY, AND NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
ALL WARRANTIES ARE EXPRESSLY DISCLAIMED.
USER ASSUMES THE FULL RISK OF USING SUCH PRODUCTS AND DOCUMENTS. IN NO EVENT SHALL USB-IF BE LIABLE
FOR ANY ACTUAL, DIRECT, INDIRECT, PUNITIVE, OR CONSEQUENTIAL DAMAGES ARISING FROM SUCH USE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THE SALE OF PRODUCTS AND TESTING COMPONENTS THROUGH THIS ORDER FORM DOES NOT IMPLY SUCH
PRODUCTS AND TESTING COMPONENTS ARE CERTIFIED AND/OR ENDORSED BY USB-IF. THESE PRODUCTS ARE FOR
TESTING PURPOSES ONLY AND NOT FOR RESALE.
Page 4 of 6
Purchasing/Return Policy
If you wish to purchase products described on the usb.org web site, you will be asked to supply
certain information, including but not limited to credit card or other payment information. You agree
all information you provide to the USB-IF will be accurate, complete and current. You agree to pay all
charges incurred by authorized users of your account and credit card or other payment mechanism
at the prices in effect when such charges are incurred. You will also be responsible for paying any
applicable taxes, and shipping and handling charges relating to your purchases.
Non-Defective Products
We will not accept returns on non-defective products.
Defective Products
Defective products may be returned for either exchange or repair (at the discretion of the USB-IF)
within 30 days from the shipment date.
No defective product will be accepted without a return authorization (RA) number. To request a RA
number, please contact a USB-IF Customer Service Specialist; please see the contact information
below. RA numbers are valid for ten business days after issue. Your RA number(s) must appear
clearly on the shipping label of the return shipment. Affix a label to the box: PLEASE DO NOT
MARK THE BOX ITSELF IN ANY WAY.
If you have questions, please contact us at:
USB Implementers Forum
3855 SW 153rd Dr.
Beaverton, OR 97003
Phone: 1-503-619-0426
Fax: 1-503-644-6708
Email: admin@usb.org
Page 5 of 6