FINISH
0671 DULUX painting
0671 DULUX PAINTING
1
GENERAL
1.1
RESPONSIBILITIES
General
Requirement: Provide DuluxGroup/Dulux coating systems to substrates, as documented and as
follows:
- Consistent in colour, gloss level, texture and dry film thickness.
- Free of runs, sags, blisters, or other discontinuities.
- Paint systems fully opaque.
- Clear finishes at the level of transparency consistent with the product.
- Fully adhered.
- Resistant to environmental degradation within the manufacturer’s stated life span.
1.2
COMPANY CONTACTS
DuluxGroup/Dulux technical contacts
Architects and Specifiers’ Hotline (Paint, Acratex, Protective Coatings): 13 23 77.
Powder Coatings Technical Advice Hotline: 13 24 99.
Website: www.dulux.com.au/contact-us/architects-and-specifiers
1.3
CROSS REFERENCES
General
Requirement: Conform to the following worksection(s):
- General requirements.
- [complete/delete]
- [complete/delete]
1.4
STANDARDS
Painting
General: To the recommendations of those parts of AS/NZS 2311 which are referenced in this
worksection.
1.5
MANUFACTURER’S DOCUMENTS
Technical manuals
Product Guide: www.dulux.com.au/specifier/product/product-selector
Duspec Product Data Sheets, MSDS, paint system selection: www.dulux.com.au/specifier/duspec
1.6
INTERPRETATION
Abbreviations
General: For the purposes of this worksection the following abbreviations apply:
- ASU: Acrylic sealer undercoat multipurpose combo product.
- DFT: Dry film thickness.
- PDS: Product data sheet.
- PRN: Paint reference number.
- PSU: Primer sealer undercoat multipurpose combo product.
- WFT: Wet film thickness.
Definitions
General: For the purposes of this worksection the definitions given in AS/NZS 2310 and the following
apply:
- Adhesion: The sum total of forces of attachment between a dry film and its substrate.
- Finish coat: The final coat of a coating system.
© NATSPEC (Oct 13)
1
[insert date]
FINISH
0671 DULUX painting
- Gloss: The optical property of a surface, characterised by its ability to reflect light specularly.
- Gloss unit: Numerical value for the amount of specular reflection relative to that of a standard
surface under the same geometric conditions.
- Levels of gloss finish: When the specular direction is 60 degrees, a surface with the following
specular gloss reading are defined by AS 1580 and as follows:
. Full gloss finish between 50 and 85 gloss units.
. Semi gloss between 20 and 50 gloss units.
. Low gloss between 5 and 20 gloss units (also known as low sheen).
. Flat finish less than 5 gloss units (also known as matt).
- Opacity: The ability of a paint to obliterate the colour difference of a substrate.
- Paint: A product in liquid form, which when applied to a surface, forms a dry film having protective,
decorative or other specific technical properties.
- Primer, prime coat: The first coat of a painting system that helps bind subsequent coats to the
substrate and which may inhibit its deterioration.
- Sealer: A product used to seal substrates to prevent:
. Materials from bleeding through to the surface.
. Reaction of the substrate with incompatible top coats.
. Undue absorption of the following coat into the substrate.
- Sheen: Gloss which is observed on an apparently matt surface at glancing angles of incidence.
- Substrate: The surface to which a material or product is applied.
- Undercoat: An intermediate coat formulated to prepare a primed surface or other prepared surface
for the finishing coat.
1.7
INSPECTION
Notice
Inspection: Give notice so that inspection may be made of the following:
- Painting stages:
. Completion of surface preparation.
. After application of prime or seal coats.
. After application of undercoat.
. After application of each subsequent coat.
- Clear finishing stages:
. Before surface preparation of timber.
. Completion of surface preparation.
. After staining.
. After sanding of sealer.
. After application of each clear finishing coat.
1.8
SUBMISSIONS
Clear finish coated samples
General: Submit pieces of timber or timber veneer matching the timber to be used in the works,
prepared, puttied, stained, sealed and coated in conformance with the specified system, of sufficient
size so that, each piece can be cut into 4 segments, marked for identification, and distributed as
directed.
Coated samples schedule
Substrate
Paint system
Colour
Sample size
e.g. Plasterboard
© NATSPEC (Oct 13)
P1
Dulux Vivid White
2
A4
[insert date]
FINISH
0671 DULUX painting
Opaque coated samples
General: Submit, on representative substrates, samples of each coating system showing surface
preparation, colour, gloss level, texture, and physical properties.
Paint
General: Dulux coatings systems have been selected for this project. Submit the manufacturer’s
details at least 3 weeks before the paint is required, as follows:
- Paint brand name and paint line quality statement.
- Material safety data sheets (MSDS) showing the health and safety precautions to be taken during
application.
- The published recommendations for maintenance.
Specialist applicators
General: Submit name and contact details of proposed specialist applicators.
Evidence of experience: [complete/delete]
Substrate acceptance
Applicator: Submit the applicator’s certification of the acceptability of the paint finish substrate.
Timing: Before commencing installation.
Warranty
Material Warranty: Submit the manufacturer’s material warranty as follows:
- Extent: Paintwork generally.
- Terms: Paint systems are suitable for their intended use.
- Warranty period: As defined by the manufacturer.
Material Performance Warranty: Submit an alternative performance warranty as follows:
- Extent: [complete/delete]
- Terms: Submit the performance criteria as defined by the manufacturer.
- Measure: As defined by the manufacturer.
- Warranty period: As defined by the manufacturer.
Timing: Before the application of the paint system.
Wet samples
General: Submit two 500 mL samples, clearly labelled, of each type of paint to be tested.
Wet samples schedule
Paint type
Colour
e.g. Dulux Acratex Acrashield Low Gloss
Garden Picket (P15.F3)
2
PRODUCTS
2.1
GENERAL
Product substitution
Other paint: Conform to PRODUCTS, GENERAL, Substitutions in the General
requirements worksection.
2.2
PAINTS
Combinations
General: Do not combine paints from different manufacturers in a paint system. Dulux paint products
and coating systems have been selected and specified for this project. Any unauthorised product
substitution will void the Warranties.
Clear timber finish systems: Provide only the combinations of putty, stain and sealer recommended by
the manufacturer of the top coats.
© NATSPEC (Oct 13)
3
[insert date]
FINISH
0671 DULUX painting
Delivery
General: Deliver paints to the site in the original manufacturer’s labelled and unopened containers.
Tinting
General: Provide only products which are colour tinted by the manufacturer or supplier.
Toxic ingredients
General: To the requirements of Appendix I Uniform Paint Standard to the Standard for the Uniform
Scheduling of Medicines and Poisons (SUSMP).
Standards
Paint types: Conform to the Australian Standard as referenced in the OCP/Dulux paint type
reference table.
DuluxGroup/Dulux paint type reference table legend
Key:
ASU = Acrylic Sealer/Undercoat.
NE = No Equivalent.
PSU = Primer/Sealer/Undercoat.
Low VOC products are noted in the Table.
^ Use is discouraged in favour of water based paints because of environmental concerns.
# These paints have either limited availability or low requirement in the Building Industry.
DuluxGroup/Dulux paint type reference table
Paint type
DuluxGroup/Dulux Dulux PDS No.
material
description
Semi gloss solvent- Dulux Super
DD0028
borne: interior
Enamel Semi-Gloss
Semi-gloss water- Dulux Aquanamel
DD1281
borne, interior
Semi Gloss
/exterior trim (alt
(low VOC)
B8b)
Gloss solventDulux Spray Pak
DD0009
borne: aerosols
Full gloss solvent- Dulux Super
DD0145
borne: exterior
Enamel Full Gloss
Full gloss solvent- Dulux Super
DD0026
borne: interior
Enamel Full Gloss
Full gloss waterDulux Aquanamel
DD1282
borne
Gloss
interior/exterior trim (low VOC)
(alt B9b)
Flat latex: exterior Dulux
DD1450
Weathershield Matt
Acrylic (low VOC)
Flat latex: interior
Dulux Wash & Wear DD1095
101 Adv Flat Acrylic
(low VOC)
Flat latex: interior
Dulux White Ceiling DD1403
Paint eco
ceilings
choice (low VOC)
Flat latex: interior
Dulux Professional DD1466
ceilings (tinted
EnvirO2 Tintable
colours)
Ceiling Flat (low
VOC)
Low gloss latex:
Dulux
DD0053
exterior
Weathershield Low
Sheen Acrylic (low
© NATSPEC (Oct 13)
4
AS/NZS
2311 PRN (Table
4.2)
B3
Standard
B41
NE
B4#
NE
B5a
AS 3730.6
B5b
AS 3730.6
B42
NE
B6a
AS 3730.7
B6b
AS 3730.1
B6c
AS 3730.1
B6d
AS 3730.1
B7a
AS 3730.8
AS 3730.5
[insert date]
FINISH
Paint type
0671 DULUX painting
DuluxGroup/Dulux Dulux PDS No.
material
description
VOC)
Dulux Wash & Wear
101 Adv Low Sheen
Acrylic (low VOC)
Dulux Wash & Wear
Kitchen & Bathroom
Low Sheen (low
VOC)
(Mouldshield ® +
Anti-Bacterial)
Semi gloss latex:
Dulux
exterior
Weathershield Semi
Gloss Acrylic
Semi gloss latex:
Dulux Wash & Wear
interior
101 Adv Semi
Gloss Acrylic (low
VOC)
Dulux Wash & Wear
Kitchen & Bathroom
Low Sheen (low
VOC)
(Mouldshield ® +
Anti-Bacterial)
Gloss latex:
Dulux
exterior
Weathershield
Gloss Acrylic
Gloss latex: interior Dulux Wash & Wear
101 Adv Gloss
Acrylic (low VOC)
Dulux Aquanamel
Gloss (low VOC)
Gloss water-borne Dulux Aquanamel
interior/exterior trim Gloss (low VOC)
(alt B9a/B9b)
Wood primer,
Dulux 1 Step Oil
solvent-borne
Based Primer
Sealer Undercoat
Wood primer, latex Dulux 1 Step Acrylic
Primer Sealer
Undercoat
Metal primer for
Dulux Quit Rust
steel – solventCold Galv. Primer
borne
Dulux Luxaprime
Zinc Phosphate
Primer
Metal primer, latex Dulux Quit Rust All
Metal (water based,
low VOC)
Metal primer for
Dulux Quit Rust All
zinc-coated
Metal (water based,
surfaces, latex
low VOC)
Metal primer for
Dulux Quit Rust
non ferrous metals All Metal (water
based, low VOC)
Low gloss latex:
interior
© NATSPEC (Oct 13)
AS/NZS
2311 PRN (Table
4.2)
Standard
B7b
AS 3730.3
DD0037
B8a
AS 3730.9
DD1097
B8b
AS 3730.2
DD0054
B9a
AS 3730.10
DD1098
B9b
AS 3730.12
DD1282
B42
NE
DD1227
B10
AS 3730.13
DD1192
B10A
AS 3730.17
DI1051
B11
AS 3730.21
DD1453
B11a#
AS 3730.15
DD1453
B12a
AS 3730.15
DD1453
B13
AS 3730.17
DD1096
DD1516
DD1516
DD1282
DI1136
5
[insert date]
FINISH
0671 DULUX painting
Paint type
DuluxGroup/Dulux Dulux PDS No.
material
description
AS/NZS
2311 PRN (Table
4.2)
Standard
Zinc-rich organic
binder/primer for
steel
Concrete and
masonry sealer
Dulux Zinc Rich 1P DI0541
Primer
B14
AS 3730.9
DD0074
DA0442
DD0217
B15
AS 3730.22
DD1187
B15a
NE
DD1449
B15b
NE
DD1402
B16
Dulux Sealer Binder
Dulux Acratex
Acraprime 501/2
Berger Gold Label
Acrylic Block Filler
Clear low viscosity Dulux AquaTread
paint for concrete Concrete Sealer
(low VOC)
Dulux DureSeal
Acrylic Dust Sealer
Moisture resistant Dulux EnvirO2
plasterboard sealer Water Based Sealer
binder
Binder (low VOC)
Concrete and
Dulux Acrylic Sealer
Undercoat eco
masonry, latex
choice (low VOC)
wallboard sealer,
sealer/undercoat, Dulux 1 Step Acrylic
Primer Sealer
Undercoat (low
VOC)
Undercoat, solvent- Dulux 1 Step Oil
borne
Based Primer
Sealer Undercoat
Undercoat, latex:
Dulux 1 Step Acrylic
exterior
Primer Sealer
Undercoat (low
VOC)
Dulux Acratex
Water Based 501/1
Undercoat, latex:
Dulux 1 Step Acrylic
interior
Primer Sealer
Undercoat (low
VOC)
Dulux Acrylic Sealer
Undercoat eco
choice (low VOC)
Wood Stain - spirit Feast Watson
Prooftint
Wood Stain - oil
Cabot’s Interior
Stain
Feast Watson
Woodshield (int/ext)
Wood Stain - latex Cabot’s Woodcraft
Stain (interior) (low
VOC)
Intergrain Natural
Stain (exterior) (low
VOC)
Interior clear
Cabot’s Cabothane
varnish, solventGloss
based, one-pack
Cabot’s Cabothane
© NATSPEC (Oct 13)
DI1118
DD1192
DD1227
B17
AS 3730.14
DD1192
B17a
AS 3730.18
B17a
AS 3730.18
DW0729
B18a
NE
DW0661
DW1248
B18b
DW0662
B18c
NE
B19
AS 3730.25 or
AS 3730.27 (for
floors)
DD0441
DD1192
DD1402
DW0758
DW0669
DW0668
DW1292
6
[insert date]
FINISH
Paint type
0671 DULUX painting
DuluxGroup/Dulux Dulux PDS No.
material
description
Satin
Cabot’s Stain &
Varnish (Satin)
Cabot’s Stain &
Varnish (Gloss)
Feast Watson
Floorclear (Satin)
Feast Watson
Floorclear (Gloss)
Feast Watson Stain
& Varnish (Satin)
Feast Watson Stain
& Varnish (Gloss)
Feast Watson
Weatherproof
Feast Watson
Satinproof
Feast Watson
Flatproof
Intergrain Ultraclear
Interior Satin (low
VOC)
Intergrain Ultraclear
Interior Gloss (low
VOC)
Cabot’s Cabothane
Water Based (gloss
or satin) (low VOC)
Feast Watson
Floorproof
DW1291
Intergrain Enviropro
Endure 1 Pack
(matt, satin or
gloss) (low VOC)
Floor varnish, clear Feast Watson
or tinted, two-pack EnviroMax (gloss,
semi gloss or low
sheen) (low VOC)
DW1420
DW1419
DW1418
Interior clear latex
varnish, waterbased, one-pack
Floor varnish,
solvent based,
clear (moisture
cure)
Floor Varnish,
water-based, onepack
Standard
B19a
AS 3730.27
B20a
AS 3730.27
B20b
AS 3730.27
B22
AS 3730.16
B22a
AS 3730.16
B23#
AS 3730.28
DW0737
DW0736
DW1295
DW1294
DW0726
DW0727
DW0730
DW0762
DW0761
DW1491
DW1490
DW0732
DW1312
DW1190
DW1038
DW1421
DW1422
Intergrain Enviropro DW1423
Endure
2 Pack (gloss, satin
or matt)
Exterior latex stain, Intergrain
DW0758
semi-transparent
NaturalStain (low
VOC)
Fence stain, latex Dulux
DD0055
paints, opaque
Weathershield
DW0660
Garden Shades
Cabot’s
Timbercolour
Exterior stain,
Cabot’s Deck &
DW1579
solvent-borne,
Exterior Stain
© NATSPEC (Oct 13)
AS/NZS
2311 PRN (Table
4.2)
7
[insert date]
FINISH
Paint type
opaque
Exterior stain,
solvent-borne,
semi-transparent
Paving paint for
concrete, solvent
Paving paint for
concrete, latex
Roofing paint, latex
(Solar reflectance)
Intumescent paints
Epoxy paint, twopack, solvent-borne
topcoats, interior
only
Epoxy paint, twopack, solvent-borne
topcoats, exterior &
pools
Epoxy paint, twopack, water based,
interior only
High Build
Recoatable twopack, solvent-borne
gloss polyurethane
Stain sealer,
solvent-borne for
water soluble stains
0671 DULUX painting
DuluxGroup/Dulux Dulux PDS No.
material
description
AS/NZS
2311 PRN (Table
4.2)
Standard
Feast Watson
Woodshield (Int/Ext)
Feast Watson
Decking Stain
Cabot’s Deck &
Exterior Stain
Berger Jet Dry
Paving Paint range
Berger Jet Dry
Aqua Tread Satin
Dulux AcraTex 962
COOLROOF with
InfraCOOL
Technology™
Refer to 0346
DULUX
Intumescent
coatings in
structural fire
protection coatings
Dulux Luxepoxy T
Enamel Finish
Dulux Durebild STE
2 Pak Epoxy (high
build & surface
tolerant)
Dulux Duremax
GPE Zinc
Phosphate
Dulux Duremax
GPE
Pool paints not
available from
Dulux
DW1248
DW1247
DW1579
B23a
NE
DD0081
B24
AS 3730.29
DD1163
B24a
NE
DA1471
B25
N/A
B28#
NE
DI1142
DI1109
B29
AS/NZS 3750.1
N/A
B29
AS/NZS 3750.1
Dulux Luxafloor
ECO2 (low VOC)
PC296
B29a
NE
Dulux Weathermax DI1156
HBR
B29c
NE
B30a
NE
Dulux PrepLock Oil
Based Stain Blocker
(low VOC)
Dulux Preplock
Shellac Stain
Blocker
Stain sealer, water Dulux PrepLock
based for oil stains Water Based Stain
Blocker (low VOC)
Chalk sealer,
Dulux Sealer Binder
surface conditioner Dulux Acraprime
© NATSPEC (Oct 13)
DI1116
DI1115
DD1308
DD1309
DD1310
B30b
DD0074
DA0442
B31
8
NE
[insert date]
FINISH
Paint type
Anti-mould
(treatment or wash
for timber)
Water-repellent for
masonry
Creosote stain
Paint remover,
solvent-borne
Paint remover,
chemical
Bituminous paints
High build
membrane or
texture coatings for
masonry and
concrete: exterior
Texture finish latex
coatings for
masonry and
plasterboard:
interior only
Clear or colourless
coatings
(waterborne) for
timber, exterior
0671 DULUX painting
DuluxGroup/Dulux Dulux PDS No.
material
description
AS/NZS
2311 PRN (Table
4.2)
Standard
Solvent Based
Primer
Intergrain TSS
DW0768
B32
NE
Dulux AquaBan
DD0002
B33
NE
No longer used
Selleys Pollystrippa
Paint Stripper
Selleys Polystrippa
Renovators’ Choice
No longer used
Dulux Acratex
Range
N/A
Poly
B35
B36a
NE
NE
Poly
B36b
NE
N/A
Acratex
B37
B38a
NE
AS/NZS 4548.1
AS/NZS 4548.2
AS/NZS 4548.3
AS/NZS 4548.4
B38b
NE
DW1401
DW1400
B39a
NE
DW0762
DW0761
DW0677
DW0678
B39b
NE
DW1420
DW1419
DW1418
DW1421
DW1422
DW1423
DW1312
DW1190
DW1038
B39c
AS 3730.27
DW0688
DW0744
B40
NE
Dulux Effects
Range (interior)
Intergrain UltraClear
Exterior
(gloss or satin)
Note: not suitable
for decking.
Clear coatings
Intergrain Ultraclear
(waterborne) for
Interior (gloss or
timber, interior
satin) (low VOC)
Cabot’s Crystal
Clear (gloss or
satin)
Clear or colourless Intergrain Enviropro
coatings
Endure
(waterborne) for
1 Pack (matt, satin
timber, interior
or gloss)
floors
(low VOC)
Intergrain Enviropro
Endure
2 Pack (gloss, satin
or matt)
Feast Watson
EnviroMax 2 Pack
(gloss, semi-gloss
or low sheen)
Sanding sealer
© NATSPEC (Oct 13)
Cabot’s Universal
Sanding Sealer
Feast Watson
Sanding Sealer
9
[insert date]
FINISH
0671 DULUX painting
Paint type
DuluxGroup/Dulux Dulux PDS No.
material
description
AS/NZS
2311 PRN (Table
4.2)
Standard
Semi-gloss latex,
interior trim (alt
B8b)
Gloss or full gloss
latex, interior trim
Penetrating Tung
Oil type varnish for
timber floors:
interior
Penetrating Tung
Oil type varnish for
timber floors:
exterior
Dulux Aquanamel
Semi-Gloss (low
VOC)
Dulux Aquanamel
Gloss (low VOC)
Feast Watson
Floorseal
Feast Watson
China Wood Oil
Intergrain Nature’s
Timber Oil
Feast Watson
Decking Oil
Intergrain
ULTRADECK (low
VOC)
Dulux Luxathane R
Dulux Weathermax
HBR
Dulux Powdercoat
Range
DD1281
B41
NE
DD1282
B42
NE
DW0734
DW0733
B43a
NE
DW0769
DW1577
DW1285
B43b
NE
DD1137
DI1156
B44
AS/NZS 3750.6
B45a
AS 3715
B45b
AS 4506
Gloss pigmented
polyurethane
Powder coatings
for non-ferrous
metals
Powder coatings
for ferrous metals
Dulux Powdercoat
Range
(www.duluxpowders
.com.au)
Low VOC Compliance Reference table
Green Star Office v3
Product Type
VOC Limits MAX g/litre DULUX Products
compared to the GBCA
Specification
COMPLIANCE CRITERIA – GBCA Specifications (obtain latest figures)
Walls and ceilings 16
Dulux Professional
Interior Semi-Gloss
Enviro2 Interior SemiGloss
Walls and ceilings 16
Dulux Wash & Wear 101
Interior Semi-Gloss
Advanced Semi Gloss
Dulux Wash & Wear
Kitchen & Bathroom
Semi Gloss
Walls and ceilings 16
Dulux Professional
Interior Low Sheen
Enviro2 Interior Low
Sheen
Walls and ceilings 16
Dulux Wash & Wear 101
Interior Low Sheen
Advanced Low Sheen
Dulux Wash & Wear
Kitchen & Bathroom Low
Sheen
Walls and ceilings
16
Dulux Professional
Interior Flat-Washable
Enviro2 Interior Flat
Walls and ceilings
16
Dulux Wash & Wear 101
Interior Flat-Washable
Advanced Flat
© NATSPEC (Oct 13)
10
VOC g/litre Untinted
<1
<5
<5
<1
<5
<5
<1
<5
[insert date]
FINISH
0671 DULUX painting
Green Star Office v3
Product Type
VOC Limits MAX g/litre DULUX Products
VOC g/litre Untinted
compared to the GBCA
Specification
Ceilings - Interior Flat
14
Ceilings - Interior Flat
14
Trim - Interior Gloss
Trim - Exterior Gloss
75
75
Trim - Interior Semigloss
Trim - Exterior Semi
Gloss
Trim - Exterior Low
Sheen
Timber Primer
75
Timber Primer
30
Binding Primer
75
75
30
30
Latex primer for
60
galvanised iron and
zincalume
Latex primer for
60
galvanised iron and
zincalume
Interior Latex Undercoat 65
Interior Latex Undercoat 65
Exterior Latex Undercoat 65
Interior Sealer
65
Interior Sealer
65
One and two pack
140
performance coatings for
floors
© NATSPEC (Oct 13)
Dulux Professional
Enviro2 Interior Flat
Dulux White Ceiling
Paint eco choice
Dulux Aquanamel Gloss
Dulux Weathershield
Gloss Acrylic
Dulux Aquanamel Semi
Gloss
Dulux Weathershield
Semi Gloss Acrylic
Dulux Weathershield
Low Sheen Acrylic
Dulux Professional
Enviro2 Acrylic Sealer
Undercoat (ASU)
Dulux Acrylic Sealer
Undercoat eco choice
Dulux Professional
Enviro2 Acrylic Sealer
Undercoat (ASU)
Dulux Professional
EnvirO2 Water Based
Sealer Binder
Dulux Galvanised Iron
Primer
<1
Dulux Quit Rust
Galvanised Iron Primer
< 60
Dulux Professional
Enviro2 Acrylic Sealer
Undercoat (ASU)
Dulux Acrylic Sealer
Undercoat eco choice
<1
Dulux One Step Acrylic
Primer Sealer Undercoat
(PSU)
Dulux Professional
Enviro2 Acrylic Sealer
Undercoat (ASU)
Dulux Luxafloor Eco2
(clear)
Dulux Luxafloor Eco2
Feast Watson
EnviroMax Clear timber
finish
< 60
11
<5
< 74
< 65
< 74
< 60
< 55
<1
<5
<1
<5
< 40
<5
<1
< 10
< 10
< 100
[insert date]
FINISH
3
EXECUTION
3.1
PREPARATION
0671 DULUX painting
Standards
General: To AS/NZS 2311 Sections 3.
Order of work
Other trades: Before painting, complete the work of other trades as far as practicable within the area to
be painted, except for installation of fittings, floor sanding and laying flooring materials.
Clear finishes: Complete clear timber finishes before commencing opaque paint finishes in the same
area.
Protection
General: Before painting, clean the area and protect it against dust entry. Use drop sheets and
masking to protect finished surfaces or other surfaces at risk of damage during painting.
Fixtures: Remove door furniture, switch plates, light fittings and other fixtures before starting to paint,
and refix in position undamaged on completion of the painting.
Adjacent surfaces: Protect adjacent finished surfaces liable to damage from painting operations.
Wet paint warning
General: Place notices conspicuously and do not remove them until the paint is dry.
Repair
General: Clean off marks, paint spots and stains progressively and restore damaged surfaces to their
original condition. Touch up new damaged decorative paintwork or misses only with the paint batch
used in the original application.
Substrate preparation
General: Prepare all substrates to receive the painting systems in accordance with AS/NZS 2311 and
the paint manufacturer’s recommendations.
Cleaning: Clean down the substrate surface. Do not cause undue damage to the substrate or damage
to, or contamination of, the surroundings.
Filling: Fill cracks and holes with fillers, sealants, putties or grouting cements as appropriate for the
finishing system and substrate, and sand smooth.
Clear finish: Provide filler tinted to match the substrate.
Clear timber finish systems: Prepare the surface so that its attributes will show through the clear finish
without blemishes, by methods which may involve the following:
- Removal of bruises.
- Removal of discolourations, including staining by oil, grease and nailheads.
- Bleaching where necessary to match the timber colour sample.
- Puttying.
- Fine sanding (last abrasive no coarser than 220 grit) to show no scratches across the grain.
Iron and steel: Remove weld spatter, slag, burrs, or any other objectionable surface irregularities and
radius all edges to a minimum of 2 mm. Degrease by solvent or alkaline cleaning.
Iron and steel blast cleaning: To AS 1627.9 and to the class specified in the specified protective
treatment. Provide a surface roughness or profile appropriate for the specified treatment. Where
steelwork to be abrasive cleaned includes irregular shapes allow for special equipment to achieve
required abrasive cleaning.
Structural steel: All exposed fixings including bolts, screws and the like, are to be painted to match
adjacent steelwork paint system.
Concrete and masonry: Before application to very smooth concrete, brick or masonry, either acid etch,
mechanically grind or abrasive track blast the surface as appropriate to provide a suitable key for the
subsequently applied coating and to remove laitance. Remove loose friable matter before filling
surface discontinuities.
Set plaster surfaces: Do not apply solvent borne paint or other impervious coatings if the moisture
content at the surface, tested with a moisture meter, exceeds 12%.
Particular requirements
General: Prepare substrates as documented in the Preparation schedule.
© NATSPEC (Oct 13)
12
[insert date]
FINISH
0671 DULUX painting
Preparation schedule
Substrate
e.g. Plasterboard
Preparation method
Dulux Duspec PPL008
Surface preparation info table
Duspec Info Sheet
Substrate group
Substrate title
PCB031
PCF010
PCF033
Aluminium for powdercoat
Asbestos
Autoclaved aerated concrete
Brick and blockwork
Cement render/premixed render
Ceramic tiles
Compressed fibre cement
sheeting
Chip board
Concrete floors/paths
Concrete floors/paths
PCK032
PTL017
Cork
Decorative tiles
PTI022
PFM056
Timber
Ferrous metals (mild steel, cast
iron)
Ferrous metals (mild steel, cast
iron)
Ferrous metals (mild Steel, cast
iron)
Fibre cement sheet (7.5 mm,
9 mm primed, 6 – 9 mm
Villaboard)
Fibreglass
Fibrous plaster, set plaster
Bituminous coatings
Glass reinforced concrete
Hardboard, masonite
Ferrous metals (mild steel, cast
iron)
Aluminium for powdercoat
Asbestos
Autoclaved aerated concrete
Brick/blockwork masonry
Cement render/premixed render
Ceramic tiles un-glazed
CFC sheet (Hardiflex, Hardiplank,
CFC, Express wall, Villaboard)
Chip board
Concrete floors/paths – acid etch
Concrete floors/paths –
commercial and industrial
Cork floor tiles
Concrete tiles, slate tiles,
terracotta tiles, ceramic tiles,
terrazzo tiles
Dressed timber
External mild steel –
commercial/industrial preparation
Ferrous metals – minor domestic
PAL047
PAS028
PAC002
PBK019
PCE007
PCT040
PCC050
PFM005
PFM009
PFC013
PFG016
PFP021
PBC030
PGC015
PHB045
PFM069
PFE071
PLX034
PMD020
PFO036
PNF004
© NATSPEC (Oct 13)
Applicable standard
Ferrous metals industrial – power
tool cleaning
Fibre cement sheet
Fibreglass surface
Fibrous plaster
Flintkote Bituminous coatings
Glass reinforced concrete
Hardboard, masonite
Internal mild steel –
commercial/industrial prep Class2
Abrasive Blast Clean
James Hardie Preprimed Fibre
James Hardie Preprimed Fibre
Cement Eave and Soffit Lining
Cement Eave & Soffit Lining
Laminates
Laminates
Medium density fibreboard
Medium density fibreboard
Expanded polystyrene system
Meshclad E.I.F.S (External
Insulated Finishing System)
Non ferrous metals
Non Ferrous Metal Surfaces
(aluminiums/alloys/brass/bronze/c Preparation
13
[insert date]
FINISH
Duspec Info Sheet
PCO018
PPL008
PCS063
PTO058
PPP043
PEA072
PPC011
PTI026
PPM068
PPF073
PRT038
PRT037
PRT039
PTI023
PSB067
PSL035
PTI003
PTI024
PTI025
PFC027
PVR061
PWP041
PZC012
PZS070
3.2
0671 DULUX painting
Substrate group
opper)
Concrete (off form, tilt up, precast)
Plaster products
Pre-coated sheet steel
(Colorbond®, etc)
Timber – previously oiled/stained
Substrate title
Off form, tilt up, pre-cast
Plaster products
Pre-coated sheet steel
(Colorbond®, etc)
Previously oiled/stained exterior
timber
Previously painted masonry
Previously painted masonry
surface
surface
Pebblecrete (exposed aggregate) Pebblecrete (exposed aggregate)
masonry
masonry
Plastics
Acrylic/polycarbonate/polystyrene
/polyurethane/PVC
Timber
Plyboard marine
Powder coated metals
Powder coated metals for painting
Polyurethane foam (Spray
Previously painted spray
Polyurethane Foam – SPF)
polyurethane foam
Roof tiles
Roof tiles clay
Roof tiles
Roof tiles concrete
Roof tiles
Roof tiles metal
Timber
Rough sawn timber
Sandstone and blockwork
Sandstone/brick/blockwork
Slate flooring
Slate flooring
Timber
Timber
Timber
Timber flooring
Timber
Timber joinery/furniture
Fibre cement sheet (7.5 mm,
Fibre cement sheet (7.5 mm, 9
9 mm Primed, 6 – 9 mm with
mm with recessed edges)
recessed edges)
Vermiculite
Vermiculate
Wallpaper
Wallpaper
Zinc coated steel (galvanized
Zinc coated steel galvanized steel
iron, galvanized steel)
Zinc coated steel (zincalume,
Zincanneal
zincanneal, zincseal)
PAINTING
Standard
General: To AS/NZS 2311 Section 6.
Light levels
General: During preparation of surfaces, painting and inspection, maintain light levels such that the
luminance (photometric brightness) of the surface is equal to the specified permanent artificial
illumination conditions or 400 lux, whichever is the greater.
Substrate moisture content
Requirement: Use a moisture meter to demonstrate that the moisture content of the substrate is at or
below the recommended maximum level for the type of paint and the substrate material.
© NATSPEC (Oct 13)
14
[insert date]
FINISH
0671 DULUX painting
Paint application
General: Apply the first coat immediately after substrate preparation and before contamination of the
substrate can occur. Apply subsequent coats after the manufacturer’s recommended drying period has
elapsed.
Painting conditions
General: Do not paint in dusty conditions, or otherwise unsuitable weather as follows unless the paint
is suitable and recommended for such conditions:
- Relative humidity: > 85%.
- Surface temperature: < 10oC or > 35oC.
Priming before fixing
General: Apply one coat of wood primer (2 coats to end grain) to the back of the following before fixing
in position:
- External fascia boards.
- Timber door and window frames.
- Bottoms of external doors.
- Associated trims and glazing beads.
- Timber board cladding.
Spraying
General: If the paint application is by spraying, use conventional or airless equipment which does the
following:
- Satisfactorily atomises the paint being applied.
- Does not require the paint to be thinned beyond the maximum amount recommended by the
manufacturer.
- Does not introduce oil, water or other contaminants into the applied paint.
Paint with known health hazards: Provide personal protection, masking, ventilation and screening
facilities generally to the standards set out for spray booths, AS/NZS 4114.1 and AS/NZS 4114.2.
Sanding
Clear finishes: Sand the sealer using the finest possible abrasive (no coarser than 320 grit) and avoid
cutting through the colour. Take special care with round surfaces and edges.
Repair of galvanizing
General: For galvanized surfaces which have been subsequently welded, power tool grind to remove
all rust and weld splatter. Remove all surface contaminants then immediately prime the affected area.
Primer: Organic zinc rich coating for the protection of steel is Dulux Zincannode 202. (AS/NZS 3750.9
Type 2).
Tinting
General: Tint each coat of an opaque coating system so that each has a noticeably different tint from
the preceding coat where possible, except for top coats in systems with more than one top coat.
Services
General: If not embedded, paint new services and equipment including in plant rooms, except
chromium, anodised aluminium, GRP, UPVC, stainless steel, non-metallic flexible materials and
normally lubricated machined surfaces. Repaint proprietary items only if damaged. Seek advice from
the manufacturer.
Windows
Operation: Ensure that opening windows function correctly before and after painting.
Door Leafs
Drying: Leave doors fixed open to allow drying. Do not allow door hardware, accessories or the like to
damage the door during the drying process.
Exclusions
Exclude the following surfaces from paint systems (unless specifically requested):
- Flexible duct connections, rubber hoses and mountings and other non metallic flexible fittings.
- Wire rope and machined surfaces.
- Metals plated or specially finished for appearance, bronze, brass, copper and stainless steel (except
as specified in the Pipe identification clause of the Services worksections).
© NATSPEC (Oct 13)
15
[insert date]
FINISH
0671 DULUX painting
Aluminium frames.
Prefinished aluminium frames to windows and doors, and trim.
Metal floor duct covers.
Raised access floors.
Floors.
Fair faced brickwork, blockwork, stonework, artificial stone and exposed aggregates.
Sprayed vermiculite.
Floors, paving, roads unless otherwise specified.
Timber roof structure.
Concealed timber roof structure.
Timber ceiling and eaves lining.
Exterior timber sheeting.
Exterior timber stairs and decking.
Plastic finishes generally
Inside of service ducts, heat exchangers, pipes and valves.
Shower seats, store shelving, work benches.
Those parts of timber fixtures, such as insides of cupboards, not visible when doors are closed,
unless otherwise specified. Insides of bathroom cabinets are not excluded and shall be painted.
- Self-finished surface such as glass and plastic laminates.
- Door hardware, including hinges.
-
4
SELECTIONS
4.1
PAINTING SCHEDULES GENERALLY
Paint system schedules
Requirement: Apply paint systems as documented in the Interior painting schedule and the Exterior
painting schedule.
General: Apply the paint system nominated for each substrate to the referenced manufacturer’s
Product Data Sheets (PDS) and Spec Sheets and include:
- The number and order of coats.
- The paint type for each coat.
Additional coats: Apply if necessary to:
- prepare porous or reactive substrates with prime or seal coats consistent with the manufacturer's
recommendations;
- achieve the total film thickness or texture specified; or
- achieve a satisfactory opacity, in the specified or required colour.
Painting systems
Standards: The scheduled DuluxGroup/Dulux paint systems override AS/NZS 2311 as follows:
- New unpainted interior surfaces: To AS/NZS 2311 Table 5.1.
- New unpainted exterior surfaces: To AS/NZS 2311 Table 5.2.
- Specialised painting systems: To AS/NZS 2311 clause 5.2 for the following final coats:
. High build textured or membrane finishes (B38 to AS/NZS 2311).
. 2 pack gloss pigmented polyurethane (B44 to AS/NZS 2311).
. 2 pack epoxy (B29 to AS/NZS 2311).
. 2 pack water based epoxy (B29A to AS/NZS 2311).
Paint Reference Number (PRN): The number in brackets against the individual product refers to the
Paint Ref. No. (PRN) listed in the DuluxGroup/Dulux paint type reference table (See PRODUCTS)
and AS/NZS 2311 Appendix D.
© NATSPEC (Oct 13)
16
[insert date]
FINISH
4.2
0671 DULUX painting
INTERIOR PAINTING SCHEDULE
Flat and matt latex: Interior
Substrate
1st coat
Plasterboard
(low VOC system)
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
Plasterboard
Dulux Acrylic
(ceilings)
Sealer Undercoat
(low VOC system) eco choice (B16)
Fibrous/set plaster Dulux Sealer
Binder (solvent
based) (B15)
Fibrous/set plaster Dulux Professional
(with glancing light Oil Based
issues)
Undercoat (B15)
Fibre cement
Dulux Acrylic
products
Sealer Undercoat
(low VOC system) eco choice (B16)
Timber and
Dulux 1 Step
veneers
Acrylic Primer
Sealer Undercoat
(B10a)
Concrete
Dulux Acrylic
(low VOC system) Sealer Undercoat
eco choice (B16)
Cement render
Dulux 1 Step
(low VOC system) Acrylic Primer
Sealer Undercoat
(B10a)
Vermiculite
Dulux Sealer
Binder (solvent
based) (B15)
Manufacturer’s
Spec Sheet Ref
SD 0001
2nd coat
3rd coat
Dulux Wash &
Wear 101 Adv Flat
(B6b)
Dulux White Ceiling
Paint eco choice
(B6c)
Dulux Wash &
Wear 101 Adv Flat
(B6b)
Dulux Professional
Matt Acrylic (B6a)
Dulux Wash &
Wear 101 Adv Flat
(B6b)
Dulux White Ceiling SD 0010
Paint eco choice
(B6c)
Dulux Wash &
SD 07468
Wear 101 Adv Flat
(B6b)
Dulux Professional SD 2172
Matt Acrylic (B6a)
Dulux Wash &
Wear 101 Adv Flat
(B6b)
Dulux Wash &
Wear 101 Adv Flat
(B6b)
Dulux Wash &
SD 3174
Wear 101 Adv Flat
(B6b)
Dulux Wash &
SD 3147
Wear 101 Adv Flat
(B6b)
Dulux Wash &
Wear 101 Adv Flat
(B6b)
Dulux Wash &
Wear 101 Adv Flat
(B6b)
Dulux Wash &
SD 1430
Wear 101 Adv Flat
(B6b)
Dulux Wash &
SD 3665
Wear 101 Adv Flat
(B6b)
Dulux White Ceiling Dulux White Ceiling SD 3505
Paint eco choice
Paint eco choice
(B6c)
(B6c)
Low gloss latex - Interior
Substrate
1st coat
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Plasterboard
(low VOC system)
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
SD 0002
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Dulux Wash &
SD 0901
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
SD 1128
Fibrous/set plaster Dulux Sealer
Binder (solvent
based) (B15)
Fibre cement
Dulux Acrylic
products
Sealer Undercoat
(low VOC system) eco choice (B16)
Timber and
veneers
Concrete
(low VOC system)
Cement render
© NATSPEC (Oct 13)
Dulux 1 Step
Acrylic Primer
Sealer Undercoat
(B10a)
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
Dulux 1 Step
17
SD 0813
SD 2971
SD 1528
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
(low VOC system)
Acrylic Primer
Sealer Undercoat
(B16)
MDF
Dulux 1 Step
Acrylic Primer
Sealer Undercoat
(B10a)
Brick and masonry Dulux Acrylic
(low VOC system) Sealer Undercoat
eco choice (B16)
Concrete blockwork Berger Gold Label
(low VOC system) Acrylic Block Filler
(B15)
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Wear 101 Adv Low Wear 101 Adv Low
Sheen (B7b)
Sheen (B7b)
Dulux Wash &
Dulux Wash &
SD 1041
Wear 101 Adv Low Wear 101 Adv Low
Sheen (B7b)
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
SD 3284
Wear 101 Adv Low
Sheen (B7b)
Dulux Wash &
SD 1027
Wear 101 Adv Low
Sheen (B7b)
Low gloss latex (mould resistant) – Interior
Substrate
1st coat
Plasterboard
(low VOC system)
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
2nd coat
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Plasterboard (MR Dulux Professional Dulux Wash &
grade)
EnvirO2 Water
Wear Kitchen &
(low VOC system) Based Sealer
Bathroom Low
Binder (B15)
Sheen (B7b)
Fibrous/set plaster Dulux Sealer
Dulux Wash &
Binder (solvent
Wear Kitchen &
based) (B15)
Bathroom Low
Sheen (B7b)
Fibre cement
Dulux Acrylic
Dulux Wash &
products
Sealer Undercoat Wear Kitchen &
(low VOC system) eco choice (B16)
Bathroom Low
Sheen (B7b)
Concrete
Dulux Sealer
Dulux Wash &
Binder (solvent
Wear Kitchen &
based) (B15)
Bathroom Low
Sheen (B7b)
Cement render
Dulux 1 Step
Dulux Wash &
(low VOC system) Acrylic Primer
Wear Kitchen &
Sealer Undercoat Bathroom Low
(B16)
Sheen (B7b)
MDF
Dulux 1 Step
Dulux Wash &
Acrylic Primer
Wear Kitchen &
Sealer Undercoat Bathroom Low
(B10a)
Sheen (B7b)
Brick and masonry Dulux Acrylic
Dulux Wash &
(low VOC system) Sealer Undercoat Wear Kitchen &
eco choice (B16)
Bathroom Low
Sheen (B7b)
Concrete blockwork Berger Gold Label Dulux Wash &
(low VOC system) Acrylic Block Filler Wear Kitchen &
(B15)
Bathroom Low
Sheen (B7b)
© NATSPEC (Oct 13)
18
3rd coat
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Dulux Wash &
Wear Kitchen &
Bathroom Low
Sheen (B7b)
Manufacturer’s
Spec Sheet Ref
SD 5013
SD 4611
SD 5008
SD 4543
SD 5009
SD 5010
SD 5011
SD 5018
SD1027
[insert date]
FINISH
0671 DULUX painting
Semi gloss latex: Interior
Substrate
1st coat
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Plasterboard
(low VOC system)
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
SD 0003
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
SD 1065
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
SD 3615
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
Dulux Wash &
Wear 101 Adv
Semi Gloss (B8b)
SD 0678
3rd coat
Manufacturer’s
Spec Sheet Ref
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
SD 4848
Fibrous/set plaster Dulux Sealer
Binder (solvent
based) (B15)
Fibre cement
Dulux Acrylic
products
Sealer Undercoat
(low VOC system) eco choice (B16)
Timber and
veneers
Dulux 1 Step
Acrylic Primer
Sealer Undercoat
(B17a)
Concrete
Dulux Acrylic
(low VOC system) Sealer Undercoat
eco choice (B16)
Cement render
Dulux
(low VOC system) Acrylic Sealer
Undercoat eco
choice (B16)
MDF
Dulux 1 Step
(low VOC system) Acrylic Primer
Sealer Undercoat
(B17a)
Brick and masonry Dulux Acrylic
(low VOC system) Sealer Undercoat
eco choice (B16)
Concrete blockwork Berger Gold Label
(low VOC system) Acrylic Block Filler
(B15)
SD 0815
SD 0903
SD 3410
SD 4804
SD 2797
Semi gloss latex (mould resistant): Interior
Substrate
1st coat
Plasterboard
(low VOC system)
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
2nd coat
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Plasterboard (MR Dulux Professional Dulux Wash &
grade)
EnvirO2 Water
Wear Kitchen &
(low VOC system) Based Sealer
Bathroom Semi
Binder (B15b)
Gloss (B8b)
Fibrous/set plaster Dulux Sealer
Dulux Wash &
Binder (solvent
Wear Kitchen &
based) (B15)
Bathroom Semi
Gloss (B8b)
Fibre cement
Dulux Acrylic
Dulux Wash &
products
Sealer Undercoat Wear Kitchen &
(low VOC system) eco choice (B16)
Bathroom Semi
Gloss (B8b)
Concrete
Dulux Acrylic
Dulux Wash &
(low VOC system) Sealer Undercoat Wear Kitchen &
© NATSPEC (Oct 13)
19
SD 4581
SD 5014
SD 4512
SD 4522
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
2nd coat
3rd coat
eco choice (B15)
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Dulux Wash &
Wear Kitchen &
Bathroom Semi
Gloss (B8b)
Cement render
(low VOC system)
Dulux 1 Step
Acrylic Primer
Sealer Undercoat
(B17a)
MDF
Dulux 1 Step
Acrylic Primer
Sealer Undercoat
(B17a)
Brick and masonry Dulux Acrylic
(low VOC system) Sealer Undercoat
eco choice (B16)
Concrete blockwork Berger Gold Label
(low VOC system) Acrylic Block Filler
(B15)
Manufacturer’s
Spec Sheet Ref
SD 5015
SD 5016
SD 5017
SD 5019
Semi gloss water based enamel: Interior
Substrate
1st coat
Plasterboard
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
Plasterboard (MR Dulux Professional
grade)
EnvirO2 Water
Based Sealer
Binder (B15b)
Fibrous/set plaster Dulux Sealer
Binder (solvent
based) (B15)
Fibre cement
Dulux Acrylic
products
Sealer Undercoat
eco choice (B16)
Timber and
Dulux Acrylic
veneers
Sealer Undercoat
(low VOC system) eco choice (B17a)
Concrete
Dulux Acrylic
Sealer Undercoat
eco choice (B17a)
Cement render
MDF
(low VOC system)
Dulux 1 Step
Acrylic Primer
Sealer Undercoat
(B17a)
Dulux Acrylic
Sealer Undercoat
eco choice (B17a)
Brick and masonry Dulux Acrylic
Sealer Undercoat
eco choice (B16)
Concrete blockwork Berger Gold Label
Acrylic Block Filler
© NATSPEC (Oct 13)
Manufacturer’s
Spec Sheet Ref
SD 2591
2nd coat
3rd coat
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel SD 4672
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
Dulux Aquanamel SD 2294
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel SD 5026
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel SD 5045
Semi Gloss Acrylic
20
SD 3058
SW 5020
SD 2295
SD 5021
SD 5022
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
(B15)
Zinc coated metals Dulux Quit Rust All
(incl. HD
Metal Primer (water
galvanized steel,
based) (B12a)
zincalume,
Galvabond,
zincanneal,
zincseal, zincprimed steel)
(low VOC system)
Shop primed or red Dulux Quit Rust All
oxide primed
Metal Primer (water
(ROZP) ferrous
based) (B11a)
metal
(low VOC system)
Non-ferrous metals Dulux Quit Rust
(incl. aluminium,
All Metal Primer
brass, copper, tin
(water based)
plate)
(B17a)
(low VOC system)
Plastics (solvent
Dulux PrepLock
resistant types e.g. Water based Stain
FRP, UPVC)
Blocker (B17a)
(low VOC system)
Manufacturer’s
Spec Sheet Ref
2nd coat
3rd coat
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
(B8b)
Dulux Aquanamel SD 5023
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel Dulux Aquanamel SD 4576
Semi Gloss Acrylic Semi Gloss Acrylic
(B8b)
(B8b)
Dulux Aquanamel Dulux Aquanamel SD 5024
Semi Gloss Acrylic Semi Gloss Acrylic
(B8b)
(B8b)
Dulux Aquanamel Dulux Aquanamel SD 5025
Semi Gloss Acrylic Semi Gloss Acrylic
(B8b)
(B8b)
Semi gloss, solvent-borne - Interior
Substrate
1st coat
Timber and primed Dulux 1 Step Oil
hardboard veneers Based Primer
Sealer Undercoat
(solvent based)
(B17)
MDF
Dulux Professional
Total Prep (B17a)
2nd coat
Dulux Super
Dulux Super
Enamel Semi Gloss Enamel Semi Gloss
(B3)
(B3)
Dulux Super
Enamel Semi Gloss
(B3)
Zinc coated metals Dulux Quit Rust All Dulux Super
(incl. HD
Metal Primer (water Enamel Semi Gloss
galvanized steel,
based) (B12a)
(B3)
zincalume,
Galvabond,
zincanneal,
zincseal, zincprimed steel)
Shop primed or red Spot Prime with
Dulux Super
oxide primed
Dulux Quit Rust All Enamel Semi Gloss
(ROZP) ferrous
Metal Primer (B11) (B3)
metal.
Non-ferrous metals Dulux Quit Rust
Dulux Super
(incl. aluminium,
Metal-Etch Primer Enamel Semi Gloss
brass, copper, tin
(B13)
(B3)
plate)
Plastics (solvent
Dulux PrepLock
Dulux Super
resistant types e.g. Water based Stain Enamel Semi Gloss
© NATSPEC (Oct 13)
3rd coat
21
Manufacturer’s
Spec Sheet Ref
SD 0041
Dulux Super
SD 4855
Enamel Semi Gloss
(B3)
Dulux Super
SD 1764
Enamel Semi Gloss
(B3)
Dulux Super
SD 2171
Enamel Semi Gloss
(B3)
Dulux Super
SD 3337
Enamel Semi Gloss
(B3)
Dulux Super
SD 3340
Enamel Semi Gloss
[insert date]
FINISH
0671 DULUX painting
Manufacturer’s
Spec Sheet Ref
Substrate
1st coat
2nd coat
3rd coat
FRP, UPVC)
Plastics (solvent
sensitive types e.g.
polystyrene)
Blocker (B17a)
Dulux PrepLock
Water based Stain
Blocker (B17a)
(B3)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
(B3)
Dulux Aquanamel SD 3356
Semi Gloss Acrylic
(B8b)
Full gloss water based enamel: Interior
Substrate
1st coat
Manufacturer’s
Spec Sheet Ref
SD 0990
2nd coat
3rd coat
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel SD 4853
Gloss Acrylic (B42)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
SD 2548
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Brick and masonry Berger Gold Label Dulux Aquanamel
Acrylic Block Filler Gloss Acrylic (B42)
(B15)
& (B9)
Concrete blockwork Berger Gold Label Dulux Aquanamel
Acrylic Block Filler Gloss Acrylic (B42)
(B15)
& (B9)
Zinc coated metals Dulux Quit Rust All Dulux Aquanamel
(incl. HD
Metal Primer (water Gloss Acrylic (B42)
galvanized steel,
based) (B12a)
& (B9)
zincalume,
Galvabond,
zincanneal,
zincseal, zincprimed steel)
(low VOC system)
Shop primed or red Dulux Quit Rust All Dulux Aquanamel
oxide primed
Metal Primer (water Gloss Acrylic (B42)
(ROZP) ferrous
based) (B11a)
& (B9)
metal
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
SD 2290
Plasterboard
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
Plasterboard (MR Dulux Professional
grade)
EnvirO2 Water
Based Sealer
Binder (B15b)
Fibrous/set plaster Dulux Sealer
Binder (solvent
based) (B15)
Fibre cement
Dulux Acrylic
products
Sealer Undercoat
eco choice (B16)
Timber and
veneers
(low VOC system)
Concrete
Dulux Acrylic
Sealer Undercoat
eco choice (B17a)
Cement render
Dulux 1 Step
Acrylic Primer
Sealer Undercoat
(B17a)
Dulux Acrylic
Sealer Undercoat
eco choice (B17a)
MDF
(low VOC system)
© NATSPEC (Oct 13)
Dulux Acrylic
Sealer Undercoat
eco choice (B16)
22
SD 5027
SD 2291
SD 5028
SD 2263
SD 1522
SD 1522
SD 5029
Dulux Aquanamel SD 4603
Gloss Acrylic (B42)
& (B9)
[insert date]
FINISH
Substrate
(low VOC system)
Non-ferrous metals
(incl. aluminium,
brass, copper, tin
plate)
(low VOC system)
Plastics (solvent
resistant types e.g.
FRP, UPVC)
(low VOC system)
0671 DULUX painting
1st coat
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Dulux Quit Rust All Dulux Aquanamel Dulux Aquanamel SD 5030
Metal Primer (water Gloss Acrylic (B42) Gloss Acrylic (B42)
based) (B17a)
& (B9)
& (B9)
Dulux PrepLock
Dulux Aquanamel Dulux Aquanamel SD 5031
Water based Stain Gloss Acrylic (B42) Gloss Acrylic (B42)
Blocker (B17a)
& (B9)
& (B9)
Full gloss, solvent-borne – Interior
Substrate
1st coat
Timber and primed Dulux 1 Step Oil
hardboard veneers Based Primer
Sealer Undercoat
(B17)
MDF (interior only) Dulux 1 Step
Acrylic Primer
Undercoat (B17a)
Zinc coated metals Dulux Quit Rust All
(incl. HD
Metal Primer
galvanized steel,
(B12a) # Apply 2
zincalume,
coats #
Galvabond,
zincanneal,
zincseal, zincprimed steel)
Shop primed or red Spot Prime with
oxide primed
Quit Rust All Metal
(ROZP) ferrous
Primer (B11)
metal.
Non-ferrous metals Dulux PrepLock
(incl. aluminium,
Water based Stain
brass, copper, tin
Blocker (B11)
plate)
Plastics (solvent
Dulux PrepLock
resistant types e.g. Water based Stain
FRP, UPVC)
Blocker (B17a)
Plastics (solvent
Dulux PrepLock
sensitive types e.g. Water based Stain
polystyrene)
Blocker (B17a)
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Dulux Super
Dulux Super
SD 0039
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Dulux Super
Enamel High Gloss
(B5)
Dulux Super
Enamel High Gloss
(B5)
Dulux Super
SD 1168
Enamel High Gloss
(B5)
Dulux Super
SD 0381
Enamel High Gloss
(B5)
Dulux Super
Dulux Super
SD 5069
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Dulux Super
Dulux Super
SD 3451
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Dulux Super
Enamel High Gloss
(B5)
Use water based
paints, not solvent
based.
Dulux Super
SD 0385
Enamel High Gloss
(B5)
Use water based
N/A
paints, not solvent
based.
Full gloss, epoxy primed enamel - Interior
Substrate
1st coat
Zinc coated metals
(incl. HD
Galvanized steel,
zincalume,
Galvabond,
zincanneal,
zincseal, zinc-
Dulux Duremax
Dulux Duraflex 2
GPE Zinc
High Gloss (B5)
Phosphate to 125
microns DFT (B29)
© NATSPEC (Oct 13)
2nd coat
23
3rd coat
Manufacturer’s
Spec Sheet Ref
Dulux Duraflex 2
High Gloss (B5)
SI 5469
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
primed steel)
Full gloss, epoxy primed two pack Polyurethane - Interior
Substrate
1st coat
Zinc coated metals
(incl. HD
Galvanized steel,
zincalume,
Galvabond,
zincanneal,
zincseal, zincprimed steel)
Dulux Duremax
GPE Zinc
Phosphate to 125
microns DFT (B29)
Manufacturer’s
Spec Sheet Ref
Dulux Duremax
Dulux Weathermax SI 3359
GPE to 100
HBR to 75 microns
microns DFT (B29) DFT (B29c)
2nd coat
3rd coat
Clear over stain on timber or veneers - Interior
Substrate
Timber and timber
veneer (solvent
based system)
Timber and timber
veneer (low VOC
water based
system)
1st coat
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Cabot’s Cabothane Cabot’s Cabothane Cabot’s Cabothane SW 1219 (gloss)
(solvent based)
(solvent based)
(solvent based)
-or(B19) Gloss or
(B19) Gloss or
(B19) Gloss or
SW 1202 (satin)
Satin
Satin
Satin
Cabot’s Woodcraft Cabot’s Cabothane Cabot’s Cabothane SW 5000
Stain (B18c)
Water Based
Water Based
(B19a) Gloss or
(B19a) Gloss or
Satin
Satin
Gloss level required: [complete/delete]
Clear coat 2 pack polyurethane - Interior
Substrate
1st coat
2nd coat
Timber
(low VOC water
based system)
Timber
(low VOC water
based system)
Timber
(low VOC water
based system)
Intergrain Enviropro Intergrain Enviropro
Timberseal (B20b) Endure 2 Pack Matt
(B20b)
Intergrain Enviropro Intergrain Enviropro
Timberseal (B20b) Endure 2 Pack
Satin (B20b
Intergrain Enviropro Intergrain Enviropro
Timberseal (B20b) Endure 2 Pack
Gloss (B20b)
Manufacturer’s
Spec Sheet Ref
Intergrain Enviropro SW 4102
Endure 2 Pack Matt SW 4050
(B20b)
Intergrain Enviropro SW 4243
Endure 2 Pack
Satin (B20b)
Intergrain Enviropro SW 3991
Endure 2 Pack
Gloss (B20b)
3rd coat
Clear coat single pack polyurethane - Interior
1st coat
2nd coat
Timber and timber
veneer (low VOC
water based
system)
Timber and timber
veneer (solvent
based system)
Intergrain Ultraclear
(B39b) Gloss or
Satin Apply
10.8 m2/litre
Feast Watson
Satinproof (solvent
based) (B19)
Intergrain Ultraclear
(B39b) Gloss or
Satin Apply
10.8 m2/litre
Feast Watson
(Optional)
SW 1244
Satinproof (solvent Feast Watson
based) (B19)
Satinproof (solvent
based) (B19)
© NATSPEC (Oct 13)
24
3rd coat
Manufacturer’s
Spec Sheet Ref
SW 3925 (gloss)
or
SW 3927 (satin)
Substrate
[insert date]
FINISH
0671 DULUX painting
Two pack gloss pigmented polyurethane- Interior joinery
Substrate
1st coat
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Timber
(all shop applied)
Dulux Luxepoxy 4
White Primer
(B29B) to 50
microns DFT.
Dulux Luxathane R Dulux Luxathane R SD 1751
(B44) to 60 microns (B44) to 60 microns
DFT.
DFT.
Clear finishing oils for timber - Interior
Substrate
1st coat
2nd coat
Timber
Feast Watson
Scandinavian Oil
Apply at 16 m2/litre
Feast Watson Tung
Oil (B43a) Apply
12-14 m2/litre
Feast Watson
Scandinavian Oil
Apply at 16 m2/litre
Feast Watson Tung
Oil (B43a) Apply
12-14 m2/litre
Timber
3rd coat
Manufacturer’s
Spec Sheet Ref
SW 1257
SW 1258
Tung oil (Semi gloss finish) - Interior (Timber floors)
Substrate
1st coat
Manufacturer’s
Spec Sheet Ref
Feast Watson Tung Feast Watson Tung SW 1313
Oil (Commercial)
Oil (Commercial)
2nd coat
3rd coat
Timber (soft wood) Feast Watson
Maxiprime
Apply 8-9 m2/litre
Timber (hardwood) Feast Watson
Feast Watson Tung Feast Watson Tung SW 1313
Maxiprime
Oil (Commercial)
Oil (Commercial)
Apply 10-11 m2/litre
Clear single pack polyurethane - Interior (Timber floors)
1st coat
Timber (floors)
(low VOC water
based system)
Intergrain Enviropro Intergrain Enviropro Intergrain Enviropro SW4012 (gloss)
Endure 1 (B39c)
Endure 1 (B39c)
Endure 1 (B39c)
or
Gloss, Satin or Matt Gloss, Satin or Matt Gloss, Satin or Matt SW4014 (satin)
or
SW4016 (matt)
Feast Watson
Feast Watson
Feast Watson
SW 1332
Floorproof (solvent Floorproof (solvent Floorproof (solvent
based) (B20a)
based) (B20a)
based) (B20a)
Gloss or Satin
Gloss or Satin
Gloss or Satin
Timber (floors)
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Substrate
Paving paint for concrete – Interior or exterior
Substrate
1st coat
2nd coat
3rd coat
Concrete
(solvent based
system)
Concrete
(low VOC, water
based system)
Berger Jet Dry
Non-Slip Paving
Paint (B24)
Berger Jet Dry
Aqua Tread Satin
(B24A)
Berger Jet Dry
Non-Slip Paving
Paint (B24)
Berger Jet Dry
Aqua Tread Satin
(B24A)
Berger Jet Dry
Non-Slip Paving
Paint (B24)
Manufacturer’s
Spec Sheet Ref
SD 0643
SD 1145
Clear sealer for concrete – Interior or Exterior
© NATSPEC (Oct 13)
25
[insert date]
FINISH
0671 DULUX painting
Substrate
1st coat
2nd coat
3rd coat
Concrete
(domestic)
(low VOC, water
based system)
Concrete
(commercial) (low
VOC, water based
system)
Concrete
(commercial)
(water based
system)
Concrete
(commercial)
(solvent based
system)
Berger Jet Dry
Aqua Tread Satin
(B15a)
Berger Jet Dry
Aqua Tread Satin
(B15a)
Berger Jet Dry
Aqua Tread Satin
(B15a)
Dulux Luxafloor
ECO2 (B29a)
Dulux Luxafloor
ECO2 (B29a)
Dulux 956/1
Acraglaze (B15a)
(Interior only)
Dulux 956/1
Acraglaze (B15a)
(Interior only)
Dulux Dureseal
ACS (B15a)
Dulux Dureseal
ACS (B15a)
Manufacturer’s
Spec Sheet Ref
SD 1145
SI 3030
(Optional)
Dulux 956/1
Acraglaze (B15a)
(Interior only)
SA 2589
SI 1574
Previously painted surfaces - Interior
- Primer: [complete/delete]
- Sealer: [complete/delete]
- Undercoat: [complete/delete]
Substrate
1st coat
2nd coat
e.g. Painted
Plasterboard
Dulux ASU (B16)
Dulux Wash &
Dulux Wash &
Wear 101 Adv Low Wear 101 Adv Low
Sheen (B7b)
Sheen (B7b)
4.3
3rd coat
Manufacturer’s
Spec Sheet Ref
SD 07451
EXTERIOR PAINTING SCHEDULES
Low gloss latex – Exterior
Substrate
1st coat
Weatherboard Dulux
hardboard cladding Weathershield Low
(Weathertex)
Sheen Acrylic
(B7a)
Weatherboard Dulux
fibre cement board Weathershield Low
cladding
Sheen Acrylic
(Hardiboard)
(B7a)
Fibre cement
Dulux
products
Weathershield Low
Sheen Acrylic
(B7a)
Timber and
Dulux
veneers
Weathershield Low
Sheen Acrylic
(B7a)
Concrete (OFC, tilt Dulux
slab or pre-cast)
Weathershield Low
Sheen Acrylic
(B7a)
Concrete (OFC, tilt Dulux AcraPrime
© NATSPEC (Oct 13)
2nd coat
3rd coat
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux AcraTex
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
(Optional) Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux AcraTex
26
Manufacturer’s
Spec Sheet Ref
SD 0035
SD 2539
SD 1333
SD 0035
SD 0994
SA 0770
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
2nd coat
slab or pre-cast)
(High-build
performance
coating system)
Cement render
(High-build
performance
coating system)
Clay brick and
masonry
501/1 Water Based AcraShield 955
Primer (B15)
Low Gloss
RollerRoller Finish
(B38a)
Dulux AcraPrime
Dulux AcraTex
501/1 Water Based AcraShield 955
Primer (B15)
Low Gloss Roller
Finish (B38a)
Dulux
Dulux
Weathershield Low Weathershield Low
Sheen Acrylic
Sheen Acrylic
(B7a)
(B7a)
Concrete blockwork Berger Gold Label Dulux
Acrylic Blockfiller
Weathershield Low
(B15)
Sheen Acrylic
(B7a)
Concrete blockwork Dulux AcraPrime
Dulux AcraTex
(High-build
501/1 Water Based AcraShield 955
performance
Primer (B15)
Low Gloss Roller
coating system)
Finish (B38a)
Zinc coated metals Dulux
Dulux
(incl. Zincalume,
Weathershield Low Weathershield Low
Galvabond,
Sheen Acrylic
Sheen Acrylic
Zincanneal,
(B7a)
(B7a)
zincseal, zincprimed steel)
HD Galvanized
Dulux Professional Dulux
steel or zinc-primed Galvanised Iron
Weathershield Low
steel
Primer (B12A)
Sheen Acrylic
(B7a)
Shop primed or red Dulux Quit Rust All Dulux
oxide primed
Metal Primer (B11) Weathershield Low
(ROZP) ferrous
Sheen Acrylic
metal.
(B7a)
Plastics (solvent
Dulux PrepLock
Dulux
resistant types e.g. Water Based Stain Weathershield Low
FRP, UPVC)
Blocker (B17A)
Sheen Acrylic
(low VOC)
(B7a)
3rd coat
AcraShield 955
Low Gloss
RollerRoller Finish
(B38a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Manufacturer’s
Spec Sheet Ref
SA 4029
SD 0312
SD 1555
SA 2957
SD 3275
Dulux
SD 5444
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
SD 2915
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
SD 5047
Weathershield Low
Sheen Acrylic
(B7a)
Semi gloss latex – Exterior
Substrate
1st coat
2nd coat
Weatherboard
Dulux Professional Dulux
hardboard cladding Acrylic Primer
Weathershield
Undercoat (B10A) Semi Gloss Acrylic
(B8a)
Fibre cement
Dulux
Dulux
products
Weathershield
Weathershield
Semi Gloss Acrylic Semi Gloss Acrylic
(B8a)
(B8a)
Timber and
Dulux Professional Dulux
veneers
Acrylic Primer
Weathershield
Undercoat (B10A) Semi Gloss Acrylic
(B8a)
© NATSPEC (Oct 13)
27
3rd coat
Manufacturer’s
Spec Sheet Ref
Dulux
SD 07488
Weathershield
Semi Gloss Acrylic
(B8a)
(Optional) Dulux
SD 5504
Weathershield
Semi Gloss Acrylic
(B8a)
Dulux
SD 07488
Weathershield
Semi Gloss Acrylic
(B8a)
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
2nd coat
Concrete (OFC, tilt Dulux AcraTex
slab or pre-cast)
Acraprime Water
Based (B8a)
Dulux
Weathershield
Semi Gloss Acrylic
(B8a)
Concrete (OFC, tilt Dulux AcraPrime
Dulux AcraTex
slab or pre-cast)
501/1 Water Based AcraShield 955
(High-build
Primer (B15)
Low Gloss Roller
performance
Finish (B38a)
coating system)
Cement render
Dulux AcraPrime
Dulux AcraTex
(High-build
501/1 Water Based AcraShield 955
performance
Primer (B15)
Low Gloss Roller
coating system)
Finish (B38a)
Clay brick and
Berger Gold Label Dulux
masonry
Acrylic Blockfiller
Weathershield
(B8a)
Semi Gloss Acrylic
(B8a)
Concrete blockwork Berger Gold Label Dulux
Acrylic Blockfiller
Weathershield
(B15)
Semi Gloss Acrylic
(B8a)
Concrete blockwork Dulux AcraPrime
Dulux AcraTex
(High-build
501/1 Water Based AcraShield 955
performance
Primer (B15)
Low Gloss Roller
coating system)
Finish (B38a)
Zinc coated metals Dulux Quit Rust All Dulux
(incl. Zincalume,
Metal Primer (B11) Weathershield
Galvabond,
Semi Gloss Acrylic
Zincanneal,
(B8a)
zincseal, zincprimed steel)
HD Galvanized
Dulux Quit Rust All Dulux
steel or zinc-primed Metal Primer (B11) Weathershield
steel
Semi Gloss Acrylic
(B8a)
Shop primed or red Dulux Quit Rust All Dulux
oxide primed
Metal Primer (B11) Weathershield
(ROZP) ferrous
Semi Gloss Acrylic
metal.
(B8a)
Plastics (solvent
Dulux PrepLock
Dulux
resistant types e.g. Water Based Stain Weathershield
FRP, UPVC)
Blocker (B17A)
Semi Gloss Acrylic
(low VOC system)
(B8a)
3rd coat
Manufacturer’s
Spec Sheet Ref
SD 4114
Dulux (Optional)
Weathershield
Semi Gloss Acrylic
(B8a)
Dulux AcraTex
SA 0770
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux (Optional)
Weathershield
Semi Gloss Acrylic
(B8a)
Dulux
Weathershield
Semi Gloss Acrylic
(B8a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux
Weathershield
Semi Gloss Acrylic
(B8a)
SA 4029
SD 3423
SD 3423
SA 2957
SD 4116
Dulux
SD 4116
Weathershield
Semi Gloss Acrylic
(B8a)
Dulux
SD 2158
Weathershield
Semi Gloss Acrylic
(B8a)
Dulux
SD 5048
Weathershield
Semi Gloss Acrylic
(B8a)
Gloss latex – exterior
Substrate
Fibre cement
products
1st coat
Dulux
Weathershield
Gloss Acrylic (B9a)
Timber and
Dulux
veneers
Weathershield
Gloss Acrylic (B9a)
Concrete (OFC, tilt Dulux
© NATSPEC (Oct 13)
Manufacturer’s
Spec Sheet Ref
SD 2938
2nd coat
3rd coat
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux
Dulux (Optional)
Weathershield
Gloss Acrylic (B9a)
Dulux
SD 0037
Weathershield
Gloss Acrylic (B9a)
Dulux (Optional)
SD 3096
28
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
slab or pre-cast)
Weathershield
Gloss Acrylic (B9a)
Concrete (OFC, tilt Dulux AcraPrime
slab or pre-cast)
501/1 Water Based
(High-build
Primer (B15)
performance
coating system)
Cement render
Dulux AcraPrime
(High-build
501/1 Water Based
performance
Primer (B15)
coating system)
Clay brick and
Dulux
masonry
Weathershield
Gloss Acrylic (B9a)
Concrete blockwork Berger Gold Label
Acrylic Blockfiller
(B15) (Optional)
Concrete blockwork Dulux AcraPrime
(High-build
501/1 Water Based
performance
Primer (B15)
coating system)
Zinc coated metals Dulux Quit Rust All
(incl. Zincalume,
Metal Primer
Galvabond,
(B12A)
Zincanneal,
zincseal, zincprimed steel)
HD galvanised
Dulux Quit Rust All
steel or zinc-primed Metal Primer
steel
(B12A)
Shop primed or red Dulux Luxaprime
oxide primed
Zinc Phosphate
(ROZP) ferrous
Primer (solvent
metal.
based) (B11)
Plastics (solvent
Dulux PrepLock
resistant types e.g. Water Based Stain
FRP, UPVC)
Blocker (B17A)
(low VOC system)
Manufacturer’s
Spec Sheet Ref
2nd coat
3rd coat
Weathershield
Gloss Acrylic (B9a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Weathershield
Gloss Acrylic (B9a)
Dulux AcraTex
SA 0770
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux AcraTex
AcraShield 955
Low Gloss Roller
Finish (B38a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux
Weathershield
Gloss Acrylic (B9a)
Dulux
SD 3774
Weathershield
Gloss Acrylic (B9a)
Dulux
SI 1992
Weathershield
Gloss Acrylic (B9a)
SA 4029
SD 5505
SD 5050
SA 2957
SD 3774
Dulux
Dulux
SD 5051
Weathershield
Weathershield
Gloss Acrylic (B9a) Gloss Acrylic (B9a)
Acrylic paint system for bagged masonry – Exterior
Substrate
1st coat
2nd coat
3rd coat
Brickwork and
concrete – flush
finish (bagged or
sponged) – no
texture
Brickwork and
concrete – flush
finish (bagged or
sponged) – slight
texture
Brickwork and
concrete – flush
Dulux Sealer
Binder (solvent
based) (B15)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
Dulux
Weathershield Low
Sheen Acrylic
(B7a)
© NATSPEC (Oct 13)
Manufacturer’s
Spec Sheet Ref
SD 1021
Dulux AcraPrime
Dulux Acratex
Dulux Acratex
501/1 Water Based AcraSand Acrylic
Acrashield (B7a)
Primer (B17A)
(2nd coat Optional)
SA 0754
Dulux AcraPrime
Dulux Acratex
501/1 Water Based Mediteranean Bag
SA 2266
29
Dulux Acratex
AcraShield
[insert date]
FINISH
0671 DULUX painting
Substrate
1st coat
2nd coat
finish – medium
texture
Primer (B17A)
Finish (2 coats)
3rd coat
Manufacturer’s
Spec Sheet Ref
3rd coat
Manufacturer’s
Spec Sheet Ref
SA 1868
Textured acrylic paint system – Exterior
Substrate
1st coat
2nd coat
Concrete,
blockwork and
cement render
Dulux Acraprime
Dulux Acratex
501/1 Water Based Contempo 959
Primer (B15)
Advance Base
Coat(B38a)
Concrete,
Dulux Acraprime
Dulux Acratex Roll
blockwork and
501/1 Water Based On 950-00 Low
cement render
Primer (B15)
Profile Texture
(B38a)
Concrete, masonry, Dulux Acraprime
Dulux Acratex
blockwork and
501/1 Water Based Acrashield 955 Low
cement render
Primer (B15)
Gloss Rolana
Finish (B38a)
Dulux Acratex
Contempo 959
Advance Finish
Coat (B38a)
Dulux Acratex
Acrashield 955
Finish (B38a)
SA 0696
Dulux Acratex
SA 0770
Acrashield 955 Low
Gloss Rolana
Finish (B38a)
Semi gloss, water-based enamel – Exterior
Substrate
Fibre cement
products
1st coat
Dulux Professional
Acrylic Sealer
Undercoat (B17A)
Timber and
Dulux Professional
veneers
Acrylic Sealer
Undercoat (B17A)
Concrete
Dulux Professional
Acrylic Sealer
Undercoat (B17A)
Cement render
Dulux Professional
Acrylic Sealer
Undercoat (B17A)
Brick and masonry Berger Gold Label
Acrylic Block Filler
(B15)
Concrete blockwork Berger Gold Label
Acrylic Block Filler
(B15)
Zinc coated metals Dulux Quit Rust All
(incl. HD
Metal Primer
galvanized steel,
(B12A)
Zincalume,
Galvabond,
Zincanneal,
zincseal, zincprimed steel)
(low VOC system)
Shop primed or red Dulux Quit Rust All
oxide primed
Metal Primer (B11)
(ROZP) ferrous
metal
© NATSPEC (Oct 13)
2nd coat
3rd coat
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Dulux Aquanamel
Semi Gloss Acrylic
(B8b)
Manufacturer’s
Spec Sheet Ref
SD 5020
SD 07476
SD 5021
SD 07495
SD 5041
SD 5041
SD 5023
Dulux Aquanamel Dulux Aquanamel SD 3556
Semi Gloss Acrylic Semi Gloss Acrylic
(B8b)
(B8b)
30
[insert date]
FINISH
Substrate
(low VOC system)
Non-ferrous metals
(incl. aluminium,
brass, copper, tin
plate)
(low VOC system)
Plastics (solvent
resistant types e.g.
FRP, UPVC)
(low VOC system)
0671 DULUX painting
1st coat
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Dulux Quit Rust All Dulux Aquanamel Dulux Aquanamel SD 5024
Metal Primer (B11) Semi Gloss Acrylic Semi Gloss Acrylic
(B8b)
(B8b)
Dulux PrepLock
Dulux Aquanamel Dulux Aquanamel
Water Based Stain Semi Gloss Acrylic Semi Gloss Acrylic
Blocker (B17A)
(B8b)
(B8b)
SD 5025
Gloss, water based enamel – Exterior
Substrate
1st coat
Fibre cement
products
Dulux Professional
Acrylic Sealer
Undercoat (B16)
Timber and
Dulux Professional
veneers
Acrylic Sealer
Undercoat (B16)
Concrete
Dulux Prepcoat
Acrylic Sealer
Undercoat (B16)
Cement render
Dulux Professional
Acrylic Sealer
Undercoat (B16)
Brick and masonry Berger Gold Label
Acrylic Blockfiller
(B15)
Concrete blockwork Berger Gold Label
Acrylic Blockfiller
(B15)
Zinc coated metals Dulux Quit Rust All
(incl. HD
Metal Primer (B11)
Galvanized steel,
Zincalume,
Galvabond,
Zincanneal,
zincseal, & zincprimed steel)
Shop primed or red Dulux Quit Rust All
oxide primed
Metal Primer (B11)
(ROZP) ferrous
metal.
Non-ferrous metals Dulux Quit Rust
(incl. aluminium,
Etch Primer (B17A)
brass, copper, tin
plate)
Plastics (solvent
Dulux PrepLock
resistant types e.g. Water Based Stain
FRP, UPVC)
Blocker (B17A)
2nd coat
3rd coat
Manufacturer’s
Spec Sheet Ref
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel
Gloss Acrylic (B42)
& (B9)
SD 5515
SD 07484
SD 5028
SD 07496
SD 1522
SD 1522
SD 2645
Dulux Aquanamel Dulux Aquanamel SD 2987
Gloss Acrylic (B42) Gloss Acrylic (B42)
& (B9)
& (B9)
Dulux Aquanamel
Gloss Acrylic
(B42) & (B9)
Dulux Aquanamel SD 5043
Gloss Acrylic (B42)
& (B9)
Dulux Aquanamel Dulux Aquanamel SD 5044
Gloss Acrylic (B42) Gloss Acrylic (B42)
& (B9)
& (B9)
Full gloss, solvent borne – Exterior
© NATSPEC (Oct 13)
31
[insert date]
FINISH
Substrate
0671 DULUX painting
1st coat
2nd coat
Timber and primed Dulux 1 Step Oil
hardboard veneers Based PSU
(solvent based)
(B17)
Zinc coated metals Dulux Quit Rust All
(incl. HD
Metal Primer (B11)
Galvanized steel,
(B12A) # Apply 2
zincalume,
coats #
Galvabond,
zincanneal,
zincseal, zincprimed steel)
Shop primed or red Spot Prime with
oxide primed
Dulux Quit Rust All
(ROZP) ferrous
Metal Primer (B11)
metal.
Non-ferrous metals Dulux PrepLock
(incl. aluminium,
Water Based Stain
brass, copper, tin
Blocker (B17A)
plate)
Plastics (solvent
Dulux Dulux
resistant types e.g. PrepLock Water
FRP, UPVC)
Based Stain
Blocker (B17A)
Plastics (solvent
Dulux Dulux
sensitive types e.g. PrepLock Water
polystyrene)
Based Stain
Blocker (B17A)
3rd coat
Dulux Super
Dulux Super
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Manufacturer’s
Spec Sheet Ref
SD 0039
Dulux Super
Dulux Super
SD 0381
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Dulux Super
Dulux Super
SD 5069
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Dulux Super
Dulux Super
SD 3451
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Dulux Super
Dulux Super
SD 0385
Enamel High Gloss Enamel High Gloss
(B5)
(B5)
Don’t use Solvent
Based, Use Water
Based Paints
Don’t use Solvent
Based, Use Water
Based Paints
N/A
Car parking line marking
Requirement:
- Apply nominally 70 mm wide line marking for car parking spaces nominated on drawings.
Materials:
- Paint System: Dulux Roadmaster WB2, spray applied to manufacturers written recommendations.
- Colour shall be white and shall not be subject to discolouration by the bitumen from the road
surface.
Application: Unless approved all paint shall be applied by a mechanical line marking sprayer. The road
surface shall be clean and dry at the time of painting. Paint shall be applied at wet thickness in the
range of 0.35 to 0.40 mm. Bitumen shall be at least 30 days old before coating.
Standard: To AS/NZS 2890.1.
4.4
ADDITIONAL DATA
Paint system characteristics schedule
Paint code
© NATSPEC (Oct 13)
Characteristic
Requirements
32
[insert date]