Hale Trailer Brake & Wheel, Inc.
HYUNDAI
SPECIFICATIONS
2016
HT Composite Plate Van
9001-9025
GVWR
GVWR:
VIN Plate:
Product Type:
Trailer to meet 68,000 pound GVWR
US- VIN plate to read in English (standard)
HT Composite
DIMENSIONS
LENGTH:
WIDTH:
HEIGHT:
Exterior
Inside
Exterior
Inside
Exterior
Inside
DECK HEIGHT:
5th WHEEL HEIGHT:
KINGPIN LOCATION:
LANDING GEAR LOCATION:
53’
52’-1.5” Nominal lining to lining
102.36”
101.5” Nominal lining to lining
13’6”
110” Nominal
Standard Application
47”
36”
107” from king pin (+1”/-0”)
TIRES & WHEELS
TIRE FURNISHED:
TIRE MANUFACTURER:
TIRE SIZE:
WHEEL FURNISH:
WHEEL MATERIAL:
WHEEL MANUFACTURER:
WHEEL SIZE:
WHEEL FINISH FOR STEEL:
WHEEL FINISH FOR ALUMINUM:
VALVE STEM & CAP:
Factory Furnished
Hankook TL01 (G), Low rolling resistance tire
295/75R 22.5
Factory Furnished
All steel wheel
HT Standard (TCC 361)
8.25 x 22.5, 5-hand hole (Steel, Inner & Outer)
Powder coated white steel disc
None (Due to all steel wheel application)
Valve stem and metal dome cap
UPPER COUPLER
APPROACH PLATE:
KING PIN (BTM MAIN) PLATE:
KINP PIN & MANUFACTURER:
FRONT BOTTOM RAIL:
UPPER COUPLER TUBE Q’TY:
¼” thick 80,000# yield – 6 support channels
¼” thick 80,000# yield
Standard (Jost) AAR Cruciform king pin
Stainless steel, with pick-up plate Striker Angle
(1) Tubing Application - joggled
BODY/BASE
FORWARD CROSSMEMBER:
LANDING GEAR CROSSMEMBER:
BAY AREA CROSSMEMBER:
RUNNING GEAR C/M SIZE:
RUNNING GEAR CROSSMEMBER:
SLIDER BODY RAIL (VT):
Steel hat shaped upper coupler to landing gear: 12” C/L
4” steel I-beams (80,000 PSI): 12” C/L (5ea)
4” steel I-beams (80,000 PSI): 12” C/L
4” High
4” steel I-beams (80,000 PSI): 12” C/L with 8” C/L last 3.4”
208” Rail length
DISCLAIMER
SPECIFICATIONS ARE BELIEVED TO BE CORRECT, BUT MAY CONTAIN ERRORS AND/OR OMISSIONS.
PHOTOGRAPHS ARE REPRESENTATIVE OF THE SUBJECT EQUIPMENT, BUT MAY NOT BE IDENTICAL.
EQUIPMENT AVAILABILITY, PRICES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Hale Trailer Brake & Wheel, Inc.
FLOOR
UPPER COUPLER TYPE:
FLOOR SPECIFICATION:
FLOOR RATINGS VT:
FLOOR – ASSEMBLY METHOD:
FLOOR SCREWS:
THRESHOLD – FINISH:
THRESHOLD PLATE:
THRESHOLD APPLICATION:
3.40” joggled with exposed coupler top plate (New STD)
1.38” (1 3/8”) Nominal domestic laminated oak hardwood
18,000 lbs. Rated Floor per TTMA-STD HT Dry Van Floor Rating
Wood floor assembly
(3) 0.31” diameter screws per board on I beams
Hot Dip Galvanized
0.13” x 12” deep steel diamond plate with screws and nuts
Standard Application
FRONT CORNER RADIUS:
FRONT PANEL & COLOR – DRY:
FRONT CORNER MATERIAL – DRY:
FRONT POSTS:
GLADHANDS:
FRONT RECEPTACLE (7-WAY):
OPTIONS:
GLADHAND/7-WAY LOCATION:
CORNER RADIUS PROTECTOR:
4” extruded aluminum
0.05” aluminum pre-painted white with natural color rivets
Extruded aluminum
(4) 2.5” deep (16GA) steel hats welded to upper coupler – Non AAR
Phillips Qwik-E with filters control line only. Overlaid
Phillips 7-way without circuit breakers, split pins with QCS plug
QCS plug connector
Overlaid on lower roadside front
(2) 0.125” x 12” alum diamond plate each side at top
SIDE MATERIAL:
FASTENERS TO BOTTOM RAIL:
6.5mm thick Composite Panel, 80K PPW Galvanized Steel, both sides
with natural color rivets
14 gauge galvanized steel “A” slotted logistic insets with Composite
panel color matching outer closure (for composite)
48” C/L Stiffener (Side Closure) – For Composite
Side top rail for composite trailer
Side bottom rail for composite
Cluster Sky Light Lens on side wall for 24” or bigger post pitch (Single
lens on two panels, next to each other, for 16” or less post pitches.)
Total 5. Both Side Wall Panel. (3) on Roadside and (2) on Curbside.
Composite Both Side Wall Panel Location from Front Specifically on
panels #5, #9 on C/S & #3, #7, #11 on R/S.
Standard rivets to attach C/Members to the side bottom rail
*REAR FRAME:
REAR DOOR OPENING SPEC.:
FLOOR LEVEL:
*DRY VAN- WHITING RU:
OPTION – DOOR INSTALL INSTRUCT:
REAR UNDER RIDE GUARD:
OPTION – HORIZ MEMBER/OTHER:
UNDERIDE BOLT SPEC.:
DOCK BUMPER:
RUBBER BUMPER LOCATION:
*TRACK PROTECTOR:
Roll-up Door, 6” Roll-up Header (New Design)
Standard application
Door to be flush with floor (STD)
Whiting Roll-up Door. Premium Plate.
Standard door installation per Manufacturer’s Recommendation
4” tube bolt on assembly with welded perforated (pooched) horizontal
Construction of two pieces standard stitch welding
Zinc plated bolts & nuts – standard
Pair 2” x 4” mold bolted bumper
Inboard of light protector bars (Standard)
12Ga x 36” High Galvanized Steel Roll-up Door Track Protector
ROOF PANEL:
ROOF BOW:
ROOF BOW CENTERS:
0.040” aluminum
16 Gauge Galvanized Steel Anti-Snag
24” centers full length
FRONT
SIDE
SIDE POSTS:
SIDE POST CENTERS:
SIDE TOP RAIL:
SIDE BOTTOM RAIL:
*SKYLIGHT-GENERAL SPEC.:
*SKYLIGHT QUANTITY:
*SKYLIGHT LOCATION:
REAR
ROOF
DISCLAIMER
SPECIFICATIONS ARE BELIEVED TO BE CORRECT, BUT MAY CONTAIN ERRORS AND/OR OMISSIONS.
PHOTOGRAPHS ARE REPRESENTATIVE OF THE SUBJECT EQUIPMENT, BUT MAY NOT BE IDENTICAL.
EQUIPMENT AVAILABILITY, PRICES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Hale Trailer Brake & Wheel, Inc.
LINING/SCUFF
FRONT LINING:
*BASE SIDE SCUFF:
*ADDITIONAL SIDE SCUFF:
*FRONT SCUFF:
CORNER FINISH/TREATMENT:
.25” top and .5” bottom plywood mounted to front posts full height
6.5” high integral alum (Composite STD) additional Scuff
W/18Ga x 6.5” Corrugated Steel Butted to Integral Aluminum
0.63” x 12” High White Recycled Plastic Mounted Over Lining to
Front Posts (Overlaid)
Standard Application
LANDING GEAR
L/GEAR SPEC.:
L/GEAR MOUTING METHOD:
L/GEAR SHOES:
L/GEAR GROUND CLEARANCE:
L/GEAR MOUNTING BRACKET:
L/GEAR CRANK HANDLE:
L/GEAR OPTIONS:
L/GEAR CROSS BRACE DESIGN:
Jost HT421.G3.17.157 5 Year Warranty Full HDG
Inboard mounting (Standard)
10” x 10” cushion foot low profile (Removable)
Nominal 12” ground clearance
Hot Dip Galvanized Large Wing Plate
Roadside
None (HT STD)
HT Standard Cross Brace attachment design
RUNNING GEAR
BOGIE TYPE:
AXLE SPACING:
AXLE ABS SYSTEM:
BOGIE & AXLE LOCATION:
SUSPENSION MANUFACTURER:
SUSPENSION CAPACITY:
SUSPENSION SPECIFICATION:
SURELOK (ANTI-DOCK):
LOCKING PIN MECHANISM:
SUSPENSION SUB-FRAME:
TYPE OF SUSPENSION SPRING:
SPRING SPECIFICAITON:
AXLE SUPPLIER:
AXLE – GENERAL SPEC.:
AXLE – TRACK LENGTH:
AXLE SPINDLE TYPE:
BRAKE LINING SIZE:
BRAKE LINING SPEC.:
BRAKE CONTROL SYSTEM:
SPRING BRAKE CONTROL:
BRAKE CONT-HOSE & ETC.:
SLACK ADJUSTER SPEC.:
BRAKE CHAMBER SPEC.:
STROKE LENGTH:
HUB SPECIFICATION:
DRUM SPECIFICATION:
HUB/DRUM-OPT (NUT & OTHER):
BEARING SPECIFICATION:
*LUBRICATION SPEC.:
*WHEEL SEALS SPEC.:
*HUBODOMETER:
*HUBODOMETER LOCATION:
Sliding Tandem (2) axle bogie
49” axle spacing
Tandem axle with 2S1M ABS system
Location to be sliding tandem axle for specified slider length w/ stop
bars @ front & rear
Hendrickson
Standard duty
Hendrickson Vantraxx HKANT40K Air Ride
Installed
Air-Assist Pin Puller or Quick Draw
Hendrickson K-2 STD Duty
Air Bag
Air Bag
Hendrickson
Axle – Tandem (2) Axle included in Slider (For 2S1M or 2S2M
System)
77 ½”
Tapered Spindle
16.5” X 7”
Hendrickson Extended Service (Abex-3030-197)
2S1M Wabco ABS
Sealco 110500 Springbrake Priority
Standard Air Line & Hose Application (US & Canada)
Gunite Auto-5.5”, 28 spline
MGM/Mirae 3030 Temper Resist w/ Standard Stroke Length
MFG’s Standard Stroke Length
HT Standard (KIC) 10 Stud Hub Piloted Outboard Iron Hub
HT Standard (KIC) Cast Drum
Standard
General
Chev delo (syn) grease
Stemco Platinum Performance, Discover Seals, Sentinel Hub Cap, Pro
Torq Nut
Stemco Hubodometer, Bracket Mounted, Reading in Miles
Roadside (LH) Front Axle
DISCLAIMER
SPECIFICATIONS ARE BELIEVED TO BE CORRECT, BUT MAY CONTAIN ERRORS AND/OR OMISSIONS.
PHOTOGRAPHS ARE REPRESENTATIVE OF THE SUBJECT EQUIPMENT, BUT MAY NOT BE IDENTICAL.
EQUIPMENT AVAILABILITY, PRICES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Hale Trailer Brake & Wheel, Inc.
*TIRE INFLATION SPEC.:
*TIRE INFLATION PRESSURE PRE SET:
Hendrickson Tire Maax Inflation system for undressed axle (this kit
include Hendrickson Hub cap for Tiremaax)
100 PSI Pre-Set
ELECTRICAL
HARNESS – GENERAL SPEC.:
HARNESS – SPECIAL FEATURE:
*FRONT LIGHT:
*REAR ID HEADER LIGHT:
*REAR ID SPECIAL FEATURE:
REAR SIDE MARKER TYPE (SHAPE):
*REAR SIDE MARKER DETAIL SPEC.:
REAR SIDE MARKER MT’G LOCATION:
S/T/TAIL LIGHT – QT’Y & TYPE:
*S/T/TAIL LIGHT – DETAIL SPEC.:
MAIN MID-TURN LIGHT:
*MAIN MID-TURN LIGHT – DETAIL SPEC.:
ABS LIGHT TYPE (SHAPE):
ABS LIGHT DETAIL SPEC:
ABS LIGHT MT’G LOCATION:
*LICENSE LIGHT:
OPTION RELATED HARNESS/WIRING:
ELECTRICAL RELATED REGULATION:
Molded Color Code Phillips Harness with QCS plug
Manufacturer’s Standard Feature
(2) Truck Lite 33275Y LED PC Rated Mounted with Grommet
(5) Vision LED [Cluster of 3ea CL11120R3 at center & 2ea CL11120R
on outboard]
Dual Function Rear Header Lights – 3 Lamps at center with Marker &
Stop functionality, 2 Lamps outboard with Marker & Turn functionality
Mini button style lamp
(2) Truck Lite 33275R LED PC RATED flush w/ grommet 33725
Anti-Theft hardware
Mounted on Standard Location on Rear Corner Post – HT STD
(4) Truck Lite 40 or 44 series (round style) or Equivalent
(4) Truck Lite 44322R LED (Super 44 Grey) Flange Mounted w/
Stainless Steel Rivets
Install the mid turn lamp
(2) Truck Lite 60272Y LED Gray Flange Mounted with Stainless Steel
Rivets
Mini button style lamp
(1) Trucklite 33275Y LED PC rated w/ 33725 w/anti-theft hardware
Mounted on standard location on rear corner post – HT STD
(1) Truck Lite 33010C LED
Standard
Standard Application
MARKING/DECALS
HT & PRODUCT TYPE DECAL PACKAGE:
DECAL PACKAGE:
DECAL OPT 2 – DECAL LOCATION:
DECAL OPT 3 – DECAL INSTALLATION:
CONSPICUITY MARKINGS:
LICENSE PLATE:
LICENSE PLATE BRK’T INSTALL:
*REGISTRATION/MANIFEST BOX:
REGISTRATION/MANIFEST BOX:
Hyundai Logo & Product Type Decals Application (For not having prepainted white panels for side/door/front, Apply White HT Corporate
decals)
Factory furnished Hyundai Information & Regulatory Decal Package
with FMCSA Specified in Notes
Standard Application
Standard Application
Hyundai standard conspicuity with logo applied to side bottom rail
Temporary for delivery. Fasten on HDG mounting plate
Standard install location – roadside below sill pane
(1) Factory Choice – Truck Lite 97960 or Phillips 16-802
Overlaid on lower R/S front
PAINT/FINISH
*UPPER COUPLER FINISH:
*CROSSMEMBER FINISH:
*AXLE & COMPONENTS FINISH:
*SUSP SUB-FRAME FINISH:
L/GEAR (K-BRACING) FINISH:
*L/GEAR (UPPER LEG) FINISH:
REAR FRAME – FINISH:
REAR FRAME – PAINT COLOR:
REAR UNDER RIDE – FINISH & SPEC.:
Stainless steel – forward section with Black undercoating inside of
upper coupler
HDG: Slider (Bogie) crossmembers w/slider rail, Others-Prime & black
undercoating for all steel crossmembers
Gray undercoating
Gray undercoating
Hot Dip Galvanized
Hot Dip Galvanized
Hot Dip Galvanized
None (For Galvanized or Stainless Steel)
Hot Dip Galvanized & Welded Horizontal Member
DISCLAIMER
SPECIFICATIONS ARE BELIEVED TO BE CORRECT, BUT MAY CONTAIN ERRORS AND/OR OMISSIONS.
PHOTOGRAPHS ARE REPRESENTATIVE OF THE SUBJECT EQUIPMENT, BUT MAY NOT BE IDENTICAL.
EQUIPMENT AVAILABILITY, PRICES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Hale Trailer Brake & Wheel, Inc.
REAR UNDER RIDE – PAINT COLOR:
None (For Galvanized or Stainless Steel)
MISCELLANEOUS
MUD FLAP PROVIDER:
MUD FLAP SPECIFICATION:
MUD FLAP MOUNTING:
*Lift Pad Spec.:
Factory furnished mud flaps
24” x 30” white plain plastic with Hyundai logo
Mounted to rear of slider frame (bogie) or STD location w/ HD washer
retainer
(8) Temporary For Delivery Only. Wood Approx. 7/8” x 6-3/8” x 48”
(*) Non-Standard Option
DISCLAIMER
SPECIFICATIONS ARE BELIEVED TO BE CORRECT, BUT MAY CONTAIN ERRORS AND/OR OMISSIONS.
PHOTOGRAPHS ARE REPRESENTATIVE OF THE SUBJECT EQUIPMENT, BUT MAY NOT BE IDENTICAL.
EQUIPMENT AVAILABILITY, PRICES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.