```Week 2 Assignments and Readings (September 15th – 21st)
APSC 100 Mod 1
D2L Homework
Week 3 pre-lecture quiz + pre-studio quiz due Monday Sept 22nd at 11:30 AM.
(Two quizzes!)
Electrical Safety due Oct 4th
APSC 100 Mod 2
APSC 111
APSC 131
WHMIS quiz (on Moodle)
Tutorial Lab #1 report due at start of week 3 lab period.
Complete pre-lab for tutorial lab #2 in time for week 3 lab period
MasteringPhysics
Assignment 2 due September 24th by 11 PM.
• Section 2.4, 2.5 (constant acceleration)
• Section 3.3 (projectile motion), 3.4 (motion in a circle)
MasteringChemistry
1.1 Introduction due September 22nd at 8:30 AM.
1.2 Introduction due September 29th “
Lecture homework
Lecture 1-04:
• Challenge question found at end of lectures slides
• Read Petrucci 111 – 118, 129 – 134
• Handout 1-07. Review of Equations
• Handout 1-08. Limiting Reagents
Lecture 2-01 (Gaseous state in review):
• Article about the working of the widget at the end of the lecture slides
 Read Petrucci 192 – 211
 Examine Petrucci worked examples: 6-4 to 6-9
 Problems Chapter 6: # 3, 13, 15
APSC 171
Lecture 2-02 (Partial pressures and van der Waals equations):
• Read Petrucci 226 – 228
• Problems Chapter 6: 19, 21, 25, 31, 39, 45, 51, 57, 63, 87, 94,
95, 103
Moodle Quiz
Week 2 online quiz due Thursday September 25th 11:55 pm.
Practice Problems from textbook:
7th Ed:
Section 13.2: # 1-2, 3-6, 9-14, 43, 44
Section 13.4: # 1-2, 3-8, 9-14
ASPC 161
6th Ed:
Section 13.2: # 1-2, 3-6, 9-14, 41, 42
Section 13.4: # 1-2, 3-8, 9-14
Required Homework
D.8.A.1 due during week 3 laboratory period (sketched on plain paper or in
workbook)
Lecture 0-3 (Orthographic Projection 2):
(4th ed.) 4.6 – 4.19: Views of Surfaces
(3rd ed.) 5.25: Similar shapes & Surfaces; PT123(127) Parallel planes
Solid Edge Help: User Interface/Basic viewing operations, Drawing 2D elements,
Create a part (Part modelling workflow overview and drawing sketches of parts)
Lecture 0-4 (Orthographic Projection 3):
(4th ed.) 5.5 - 5.7: Fillets, Rounds, Runouts, Conventional Edges
(3rd ed.) 5.36 - 5.38: Fillets, Rounds, Runouts, Conventional Edges
Solid Edge Help: Round command, chamfer command
ASPC 151
Recommended Homework:
D.8.G: Draw third view
Lab 1 Exercise 2 due at start of week 3 laboratory period (pages 37-43).
• Background C (49-68)
• Background B (45-48)
Recommended pre-lab reading for Week 3 lab (pages 69-87 in the lab manual)
Recommended materials for lab #2 (week 3 lab)
• Pocket knife
• Magnet
• Magnifying glass
• Textbook (this one is mandatory)
• Chapter 2: Minerals
Other
•
•
•
•
MOD 3: Project selection available on D2L, selection form to be filled out
by Sept 28th at midnight.
GPAS
Jacket Council: Tuesday September 23rd at Clark Hall 6 pm
Year crest submissions due by September 26th at 4:30
GPA fitting September 27th and 28th at Clark Hall
```